How it Works
Panasonic
Loading...
TX-P50C10B
Service manual
127 pgs10.11 Mb0
User Manual
72 pgs4.28 Mb0
Table of contents
Loading...

Panasonic TX-P50C10B, TX-P50C10E Service manual

ORDER NO. PCZ0904056CE

Plasma Television

Model No. TX-P50C10B
TX-P50C10E
GPH12DE Chassis
© Panasonic Corporation 2009. Unauthorized copying and distribution is a violation of law.

1 Safety Precautions

1.1. General Guidelines

1. When servicing, observe the original lead dress. If a short circuit is found, re place all parts which have been overheated or damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
4. When servicing, observe the original lead dress. If a short circuit is found, re place all parts which have been overheated or damaged by the short circuit.
5. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
6. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

1.2. Touch-Current Check

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure 1.
3. Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reserve the AC plug in the AC outlet and repeat each of the above measure.
6. The potential at any point (TOUGH CURRENT) expressed as voltage U For a. c.: U1 = 35 V (peak) and U2 = 0.35 V (peak); For d. c.: U
Note:
The limit value of U mA d. c.
The limit value U
7. In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.
= 1.0 V,
1
= 0.35 V (peak) for a. c. and U1 = 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and 2.0
2
= 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100 kHz.
1
and U2, does not exceed the following values:
1
Figure 1
3

2Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec­trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor [chip] components. The following techniques should be used to help reduce the incid ence of component damage caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface su ch as alumi­num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder rem oval devices not classified as [anti-static (ESD protected)] can generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara­ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the brush­ing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
4

2.2. About lead free solder (PbF)

Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing proc ess and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.
Caution
• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher. Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).
• Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C). If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb sol ­der. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. How­ever, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
5

3 Service Navigation

3.1. Service Hint

Board Name Function Board Name Function
P Power Supply C1 Data Driver (Lower Right)
C2 Data Driver (Lower Center)
A DC-DC Converter, Tuner
Speaker out, AV Terminal, AV Switch Digital Signal Processor, SYSTEM MPU, HDMI Switch Peaks lite 2p Format Converter, Plasma AI, Sub-Field Processor
K Remote receiver, Power LED S Power Switch
GK Key Switch
C3 Data Driver (Lower Left) SC Scan Drive SS Sustain Drive
SS2 Sustain out (Lower)
SU Scan out (Upper)
Non-serviceable. SU-Board should be exchanged for service.
SD Scan out (Lower)
Non-serviceable. SD-Board should be exchanged for service.
6

3.2. Applicable signals

COMPONENT (Y, PB, PR), HDMI
* Mark: Applicable input signal
Signal name COMPONENT HDMI 525 (480) / 60i * * 525 (480) / 60p * * 625 (576) / 50i * * 625 (576) / 50p * * 750 (720) / 60p * * 750 (720) / 50p * * 1,125 (1,080) / 60i * * 1,125 (1,080) / 50i * * 1,125 (1,080) / 60p * 1,125 (1,080) / 50p * 1,125 (1,080) / 24p *
PC (from HDMI terminal)
Applicable input signal for PC is basically compatible to HDMI standard timing.
Signal name Horizontal frequency (kHz) Vertical frequency (Hz) 640 × 480 @60 Hz 31.47 60.00 750 (720) / 60p 45.00 60.00 1,125 (1,080) / 60p 67.50 60.00
Note
• Signals other than above may not be displayed properly.
• The above signals are reformatted for optimal viewing on your display.
• PC signal is magnified or compressed for display, so that it may not be possible to show fine detail with sufficient clarity.
7

4 Specifications

Power Source AC 220-240 V, 50 / 60 Hz Power Consumption 350 W Power Consumption in Standby mode 0.5 W (Without monitor out recording)
15 W (With monitor out recording)
Display panel
Aspect Ratio 16:9 Visible screen size 127 cm (diagonal) 1,106 mm (W) × 622 mm (H) Number of pixels 1,049,088 (1,366 (W) × 768 (H)) [4,098 × 768 dots]
Sound
Speaker 160 mm × 40 mm × 2 pcs, 6 Ω Audio Output 20 W ( 10 W + 10 W ), 10 % THD Headphones M3 (3.5 mm) stereo mini Jack × 1
Receiving Systems / Band name (B only)
PAL I : UHF E21-68 PAL 525/60 : Playback of NTSC tape from some PAL Video recorders (VCR)
or NTSC disc playback from DVD player and recorder.
DVB-T : Digital terrestrial services via UHF aerial input. M.NTSC : Playback from M.NTSC Video recorders (VCR). NTSC (AV input only) : Playback from NTSC Video recorders (VCR).
Receiving Systems / Band name (E only)
PAL B, G, H, I, SECAM B, G, SECAM L, L’
VHF E2 - E12 VHF H1 - H2 (ITALY) VHF A - H (ITALY) UHF E21 - E69 CATV (S01 - S05) CATV S1 - S10 (M1 - M10) CATV S11 - S20 (U1 - U10) CATV S21 - S41 (Hyperband)
PAL D, K, SECAM D, K
VHF R1 - R2 VHF R3 - R5 VHF R6 - R12 UHF E21 - E69
PAL 525/60 Playback of NTSC tape from some PAL Video recorders (VCR) DVB-T Digital terrestrial services M.NTSC Playback from M. NTSC Video recorders (VCR) NTSC (AV input only) Playback from NTSC Video recorders (VCR)
O TV signals may not be received in some areas.
Aerial - Rear UHF (B), VHF / UHF (E) Operating Conditions
Temperature: 0 °C - 35 °C Humidity: 20 % - 80 % RH (non-condensing)
Connection Terminals
AV1 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, Q-Link) AV2 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link) AV3
VIDEO RCA PIN Type × 1 1.0 V [p-p] (75 Ω) S-VIDEO Mini DIN 4-pin Y:1.0 V [p-p] (75 Ω) C:0.286 V [p-p] (75 Ω) AUDIO L - R RCA PIN Type × 2 0.5 V [rms]
COMPONENT
VIDEO Y 1.0 V [p-p] (including synchronization)
P
, P
B
R
AUDIO L - R RCA PIN Type × 2 0.5 V [rms]
Others
HDMI1 / 2 TYPE A Connectors HDMI™ (Version 1.3a with x.v.Colour™)
O This TV supports [HDAVI Control 4] function.
Card slot SD Card slot × 1
Output
AUDIO L - R RCA PIN Type × 2 0.5 V [rms] (high impedance)
Dimensions (W × H × D) 1,218 mm × 822 mm × 387 mm (With Pedestal)
1,218 mm × 769 mm × 100 mm (TV only)
Mass 36.0 kg Net (With Pedestal)
34.0 kg Net (TV only)
± 0.35 V [p-p]
Note
• Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
• This equipment complies with the EMC standards listed below. EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024.
• Pedestal: ST-42RF1WG / ST-50RF1WG (For safety approval)
8

5 Service Mode

5.1. How to enter into Service Mode

While pressing [VOLUME ( - )] button of the main unit, press [0] button of the remote control three times within 2 seconds.

5.1.1. Key command

[1] button...Main items Selection in forward direction [2] button...Main items Selection in reverse direction [3] button...Sub items Selection in forward dire cti o n [4] button...Sub items Selection in reverse direction [RED] button...All Sub items Selection in forward direction [GREEN] button...All Sub items Selection in reverse direction [VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )
9

5.1.2. Contents of adjustment mode

• Value is shown as a hexadecimal number.
• Preset value differs depending on models.
• After entering the adjustment mode, take note of the value in each item before starting adjustment.

5.1.3. How to exit

Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
10

5.2. Service tool mode

5.2.1. How to access

1. Select [SRV-TOOL] in Service Mode.
2. Press [OK] button on the remote control.

5.2.2. Display of SOS History

SOS History (Number of LED blinking) indication. From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment. This indication will be cleared by [Self-check indication and forced to factory shipment setting].

5.2.3. POWER ON Time, On/Off

Note : To display Time, On/Off menu, highlight position, then press MUTE for 3sec. Time : Cumulative power on time, indicated hour : minute by decimal On/Off : Number of On/Off switching by decimal Note : This indication will not be cleared by either of the self-checks or any other command.

5.2.4. Exit

1. Disconnect the AC cord from wall outlet or switch off the power with [ Power ] button on the main unit.
11

5.3. Hotel mode

1. Purpose Restrict a function for hotels.
2. Access command to the Hotel mode setup menu In order to display the Hotel mode setup menu, please enter the following command (within 2 second). [TV] : Vol. [Down] + [REMOTE] : AV (3 times)
Then, the Hotel mode setup menu is displayed.
3. To exit the Hotel mode setup menu Disconnect AC power cord from wall outlet.
4. Explain the Hotel mode setup menu
item Function Hotel Mode Select hotel mode ON/OFF Initial INPUT Select input signal modes.
Set the input, when each time power is switched on. Selection : Off/Analogue/DVB-T/AV1/AV2/AV2S/AV3/AV3S/ COMPONENT/HDMI1/HDMI2
• Off: give priority to a last memory. However, Euro model is compulsorily set to TV.
• AVnS/AVnC: only Euro model selectable
• PC: selectable with VGA option
Initial POS Select programme number.
Selection : Off/0 to 99
• Off: give priority to a last memory
Initial VOL level Adjust the volume when each time power is
switched on. Selection/Range : Off/0 to 63
• Off: give priority to a last memory
Maximum VOL level
Button lock Select local key conditions.
Remote lock Select remote control key conditions.
Adjust maximum volume. Range : 0 to 63
Selection : Off/SETUP/MENU/ALL
• Off: altogether valid
• SETUP: only F-key is invalid (Tuning guide(menu) can not be selected.)
• MENU: only F-key is invalid (only Volume/Mute can be selected.)
• ALL: altogether invalid.
Selection : Off/SETUP/MENU
• Off: altogether valid
• SETUP: only Setup menu is invalid
• MENU: Picture/Sound/Setup menu are invalid
12

6 Troubleshooting Guide

Use the self-check function to test the unit.
1. Checking the IIC bus lines
2. Power LED Blinking timing

6.1. Check of the IIC bus lines

6.1.1. How to access

Self-check indication only: Produce TV reception screen, and while pressing [VOLUME ( - )] bu tton on the ma in unit, press [OK] button on the remote control for more than 3 seconds. Self-check indication and forced to factory shipment setting: Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, p r ess [MENU] button on the remote con-
trol for more than 3 seconds.

6.1.2. Screen display

6.1.3. Check Point

Confirm the following parts if NG was displayed.

6.1.4. Exit

Disconnect the AC cord from wall outlet or switch off the power with [ Power ] button on the main unit.
13

6.2. Power LED Blinking timing chart

1. Subject Information of LED Flashing timing chart.
2. Contents When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
14

6.3. No Power

First check point There are following 2 states of No Power indication by power LED.
1. No lit
2. Red is lit then turns red blinking a few seconds later. (See 6.2.)
15

6.4. No Picture

16

6.5. Local screen failure

Plasma display may have local area failure on the screen. Fig-1 is the possible defect P.C.B. for each local area.
Fig-1
17

7 Service Fixture & Tools

7.1. SC jig

Purpose:
To find the failure board (SC or SU/SD) when the power LED is blinking 7 times.
SC jig:
Jumper connector to connect to SC50 connector on SC board
Part number:
TZSC09187
How to use: Caution: Remove SC jig from SC board after inspection.
1. Remove all connector between SC board and SU/SD board to isolate SC board from both SU and SD board electrically. Note: The board will be damaged if al l connector is n ot removed (for example; remove conn ector only for SU board and stay connecting with SD board. The board will be damaged.)
2. Connect SC jig to connector SC50 at left bottom side of SC board
3. Turn of the TV/Display Unit and confirm the power LED blinking. LED blinking: Possible cause of failure is in SC board No LED blinking (Lighting or no lighting): Possible cause of failure is in SU or SD board
4. After inspection, turn off the TV/Display Unit and wait a few minutes to discharge.
5. Remove SC jig from SC board.
Remark: This SC jig can be used for all 2009 Plasma TV and Plasma Display.
18

8 Disassembly and Assembly Instructions

8.1. Remove the Rear cover

1. See Service Hint (Section 3)

8.2. Remove the P-Board

Caution:
To remove P.C.B. wait 1 minute after power was off for dis­charge from electrolysis capacitors.
1. Unlock the cable clampers to free the cable
2. Disconnect the connectors (P2, P6, P7, P9, P11, P25, P34 and P35).
3. Remove the screws (×9 ) and remove the P-Board.

8.4. Remove the Tuner unit

1. Unlock the cable clampers to free the cable.
2. Disconnect the connectors (A1, A7, A11, A12 and A25).
3. Disconnect the flexible cables (A20, A31 and A32).
4. Remove the screws (×2 , ×1 ) and remove the Tuner unit.

8.3. Remove the Side terminal cover and Rear terminal cover

1. Remove the claw (×1 ).
2. Remove the Side terminal cover.
3. Remove the screws (×4 , ×3 ).
4. Remove the Rear terminal cover.
19

8.5. Remove the A-Board

1. Remove the Tuner unit. (See section 8.4.)
2. Remove the screws (×4 ) and remove the A-Board.

8.6. Remove the Speakers

1. Unlock the cable clampers to free the cable.
2. Disconnect the relay connector.
3. Remove the screws (×2 ) and remove the Speaker R.
4. Disconnect the connector (A12). (See section 8.4.)
5. Remove the screws (×2 ) and remove the Speaker L.

8.7. Remove the Control button unit

1. Disconnect the connector (C14).
2. Remove the screws (×1 , ×1 ).
3. Remove the Control button unit.

8.8. Remove the GK-Board

1. Remove the Control button unit. (See Section 8.7.)
2. Remove the screws (×2 ).
3. Remove the GK-Board MTG. metal.
4. Remove the claw (×3 ).
5. Disconnect the connector (GK1).
6. Remove the GK-Board from Control button.
20

8.9. Remove the SU-Board

1. Remove the flexible cables (SU1B, SU2B, SU3B and SU4B) connected to the SU-Board.
2. Remove the flexible cable (SU11-SD11) and the bridge connector (SC41-SU41).
3. Remove the molding prop (×1 ).
4. Remove the screws (×2 , ×2 ) and remove the SU- Board.

8.11. Remove the SC-Board

1. Remove the SU-Board and SD-Board. (See section 8.9. and 8.10.)
2. Unlock the cable clampers to free the cable.
3. Disconnect the connectors (SC2 and SC3).
4. Disconnect the flexible cable (SC20).
5. Remove the screws (×6 ) and remove the SC-Board.

8.10. Remove the SD-Board

1. Remove the Control button unit. (See section 8.7.)
2. Remove the flexible cables (SD1B, SD2B, SD3B and SD4B) connected to the SD-Board.
3. Remove the flexible cable (SU11-SD11) and the bridge connectors (SC42-SD42 and SC46-SD46).
4. Remove the molding prop (×1 ).
5. Remove the screws (×2 , ×2 ) and remove the SD- Board.

8.12. Remove the SS2-Board

1. Remove the Tuner unit. (See section 8.4.)
2. Disconnect the bridge connector (SS22-SS24) and dis­connect the flexible cable (SS58).
3. Remove the screws (×2 ) and remove the SS2-Board.
21

8.13. Remove the SS-Board

1. Remove the Tuner unit. (See section 8.4.)
2. Unlock the cable clampers to free the cable.
3. Disconnect the connectors (SS3, SS11 and SS23).
4. Disconnect the flexible cables (SS52 and SS55).
5. Disconnect the bridge connector (SS22-SS24).
6. Remove the screws (×5 ) and remove the SS-Board.

8.14. Remove the Hanger metals and the Stand brackets

1. Remove the Plasma panel section from the servicing stand and lay on a flat surface such as a table (covered by a soft cloth) with the Plasma panel surface facing downward.
2. Remove the Hanger metals (L, R) fastening screws (×4
each) and remove the Hanger metals (L, R).
3. Remove the Stand brackets (L, R) fastening screws (×4 each) and remove the Stand bracket metals (L, R)
and the Stand brackets (L, R).

8.15. Remove the C1-Board

1. Remove the Control button unit. (See section 8.7.)
2. Remove the flexible cables holder fastening screws (×6 ).
3. Disconnect the flexible cables (CB1, CB2 and CB3).
4. Disconnect the flexible cable (C10).
5. Disconnect the connector (C14).
6. Remove the screws (×3 ) and remove the C1-Board.

8.16. Remove the C2-Board

1. Remove the Hanger metal R and the Stand bracket R.
(See section 8.14.)
2. Remove the flexible cables holder fastening screws (×8 ).
3. Disconnect the flexible cables (CB4, CB5, CB6 and CB7).
4. Disconnect the flexible cables (C20, C21 and C22).
5. Remove the screws (×4 ) and remove the C2-Board.
22

8.17. Remove the C3-Board

1. Remove the Tuner unit. (See section 8.4.)
2. Remove the Hanger metal L and the Stand bracket L. (See section 8.14.)
3. Remove the flexible cables holder fastening screws (×8
).
4. Disconnect the flexible cables (CB8, CB9, CB10 and CB11).
5. Disconnect the flexible cables (C31 and C32).
6. Disconnect the connectors (C33 and C35).
7. Remove the screws (×4 ) and remove the C3-Board.
2. For leaving the plasma panel from the front frame, pull the bottom of the cabinet assy forward, lift, and remove.
8.18. Remove the Plasma panel sec­tion from the Cabinet assy (glass)
1. Remove the cabinet assy and the plasma panel fastening screws (×2 ).
3. Remove the Rear cover hooks (L, R).

8.19. Remove the S-Board

1. Remove the Cabinet assy. (See section 8.18.)
2. Remove the S-Board shield case.
23
3. Remove the screws (×2 ) and remove the S-Board unit.
4. Disconnect the connector (S1).
5. Remove the Power button.
6. Remove the screw (×1 ) and remove the S-Board.
10. Remove the Glass holder bottom front and the Glass holder top front.

8.21. Remove the K-Board

1. Remove the Front glass. (see section 8.20)
2. Remove the claw (×1 ).
3. Disconnect the connector (K1) and Remove the K-Board from LED Panel.

8.20. Remove the Front glass

1. Remove the Cabinet assy. (See section 8.18.)
2. Remove the S-Board. (See section 8.19.)
3. Remove the screws (×7 ).
4. Remove the Glass holder bottom rear.
5. Remove the screws (×4 ).
6. Remove the Glass holder side (L, R).
7. Remove the screws (×9 ).
8. Remove the Glass holder top rear.
9. Remove the Front glass.
24

8.22. Replace the plasma panel

Caution:
A new plasma panel itself without Hanger metals is fragile. To avoid the damage to new plasma panel, carry a new plasma panel taking hold of the Hanger metals after assembling the Hanger metals and the Stand brackets.
1. Place a carton box packed a new plasma panel on the flat surface of the work bench.
2. Open a box and without taking a new plasma panel; Attach the C1-Board, C2-Board and the C3-Board, con­nect the flexible cables from the plasma panel to the C1­Board, C2-Board and the C3-Board, and fit the flexible cable holders.
3. Attach the Hanger metals and the Stand brackets to the new plasma panel.
4. Place the plasma panel on the servicing stand taking hold of the Hanger metals.
5. Attach the cabinet assy and each P.C.Board and so on, to the new plasma panel.
*When fitting the cabinet assy, be careful not to allow any debris, dust or handling residue to remain between the front glass and plasma panel.
25

9 Measurements and Adjustments

9.1. Adjustment Procedure

9.1.1. Driver Set-up

9.1.1.1. Item / Preparation
1. Input a white signal to plasma video input.
2. Set the picture controls as follows. Picture menu: Dynamic PNR: Min Aspect: 16:9
Caution
1. First perform Vsus adjustment.
2. The Vscn voltages are measured from the Vad (Vad_base), but may be measured from the GND (GND_base) in an unavoidable case.
9.1.1.2. Adjustments
Adjust driver section voltages referring the panel data on the panel data label. Check or adjust the following voltages with the multimeter.
Name Test Point Voltage Volume Remarks Vsus TPVSUS (SS) Vsus ± 2V R737 (P) * Ve TPVE (SS) Ve ± 2.5V Fixed * Vset TPVSET (SC) 290V ± 9V Fixed Vad TPVAD (SC) -180V ± 2V VR16600 (SC) Vscn TPVSCN (SC) Vad_base : + 145V ± 4V
GND_base : - 35V ± 6V
Vda TPVDA (P) 60V + 1V, - 2V Fixed
Fixed
*See the Panel label.
26

9.1.2. Initialization Pulse Adjust

1. Input the White signal to plasma video input.
2. Set the picture controls as follow s. Picture menu : Dynamic PNR : Min Aspect : 16:9
3. Connect Oscilloscope to TPSC1 (SC). Check the voltage (T2) at 100μs period on the down slop.
Test point Volume Level
T2 TPSC1 (SC) VR16601 (SC) 210 V ± 10 V

9.1.3. P.C.B. (Printed Circuit Board) exchange

9.1.3.1. Caution
1. To remove P.C.B., wait 1 minute after power was off for discharge from electrolysis capacitors.
9.1.3.2. Quick adjustment after P.C.B. exchange
Adjust the following voltages with the multimeter.
P.C.B. Name Test Point Voltage Volume Remarks P Board Vsus TPVSUS (SS) Vsus ± 2V R737 (P) * SC Board Vad TPVAD (SC) -180V ± 2V VR16600 (SC) A Board White balance and Sub brightness for RF and 1080i signals
*See the Panel label.
Caution:
Absolutely do not reduce Vsus below Ve not to damage the P.C.B.
27

9.1.4. Adjustment Volume Location

9.1.5. Test Point Location

28

9.2. Adjustment

9.2.1. Sub-Contrast adjustment

Name of measuring instrument Connection Remarks RF generator Base Band signal generator HD signal generator
Steps Remarks
Adjustment of TV (RF system)
Note:
In adjustment, you must setting to modulation of signal at 85%.
Ref.:
RF signal modulation spec. UK models: 80% Other models: 90%
1. Receive a RF PAL 100% Full White or Split Colour bar shown as below.
2. Goes into service adjustment mode.
3. Push a [ 1 ] or [ 2 ] key, and goes into adjustment mode for [ CONTRAST ].
Adjustment
1. The colour key yellow button of remote control is pushed.
2. The OSD character of sub-contrast becomes red. (Inside under automatic adjustment)
3. The OSD character of sub-contrast returns to black.
4. End.
Note:
Sub-contrast adjustment is unadjusted for AV/ HD input. But, when needing the adjustment cho­sen manually, please refer to [ alterna­tive method ].
29
Steps Remarks
Another procedure
Adjustment of AV system
1. PAL 100% Full White or Split Colour bar receive AV1(or AV2), shown as below.
2. Goes into service adjustment mode.
3. Push [ 1 ] or [ 2 ] key, and goes into adjustment mode for [ Contrast ].
Adjustment
1. The colour key yellow button of remote control is pushed.
2. The OSD character of sub-contrast becomes red. (Inside under automatic adjustment)
3. The OSD character of sub-contrast returns to black.
4. End.
Steps Remarks
Another procedure
Adjustment of HD system
1. At 1080i 100% Full White or Split colour bar receive component signal, as shown below.
2. Goes into service adjustment mode.
3. Push [ 1 ] or [ 2 ] key, and goes into adjustment mode for [ Contrast ].
Adjustment
1. The colour key yellow button of remote control is pushed.
2. The OSD character of sub-contrast becomes red. (Inside under automatic adjustment)
3. The OSD character of sub-contrast returns to black.
4. End.
30
Loading...
+ 97 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use