Panasonic TH-85PF12U User Manual

Operating Instructions

High Deﬁ nition Plasma Display

Model No.

TH-85PF12U

English

The illustration shown is an image.

Before connecting, operating or adjusting this product, please read these instructions completely.

Please keep this manual for future reference.

TQBC2502

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: To reduce the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualiﬁ ed service personnel.

The lightning flash with arrow-head within a triangle is in tend ed to tell the user that parts inside the product are a risk of electric shock to per sons.

The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the ap pli ance.

WARNING : To prevent damage which may result in ﬁ re or shock hazard, do not expose this apparatus to rain

or mois ture. Do not place containers with water (ﬂ ower vase, cups, cosmetics, etc.) above the set. (including on shelves above, etc.)

WARNING : 1) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to

qualiﬁ ed service personnel.

2) Do not remove the grounding pin on the power plug. This apparatus is equipped with a three pin grounding-type power plug. This plug will only ﬁ t a grounding-type power outlet. This is a safety fea ture. If you are unable to insert the plug into the outlet, contact an electrician.

Do not defeat the purpose of the grounding plug.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁ ers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments / accessories speciﬁ ed by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table speciﬁ ed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.

Dear Panasonic Customer

Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment

from your new Plasma Display.

To obtain maximum benefit from your set, please read these Instructions before making any adjustments,

and retain them for future reference.

Retain your purchase receipt as well, and record the model number and serial number of your set in the

space provided on the rear cover of these instructions.

Visit our Panasonic Web Site http://panasonic.net

Table of Contents

Important Safety Instructions .................................. 3

FCC STATEMENT ...................................................... 5

Safety Precautions ................................................... 6

Maintenance .............................................................. 7

Accessories .............................................................. 8

Accessories Supplied .............................................. 8

Remote Control Batteries ........................................ 8

Connections .............................................................. 9

AUDIO OUT Terminals connection .......................... 9

PC Input Terminals connection .............................. 10

SERIAL Terminals connection ................................11

HDMI connection .................................................... 12

COMPONENT / RGB connection .......................... 12

Power ON / OFF ..................................................... 13

Selecting the input signal ...................................... 15

Basic Controls ........................................................ 16

ASPECT Controls ................................................... 18

MULTI PIP ................................................................ 19

Digital Zoom ............................................................ 22

On-Screen Menu Displays ..................................... 23

Adjusting POS. /SIZE ............................................. 25

PICTURE Adjustments ........................................... 28

ADVANCED SETTINGS ........................................ 29

Picture Proﬁ les ....................................................... 30

Saving proﬁ les ....................................................... 31

Loading proﬁ les ..................................................... 32

Editing proﬁ les ....................................................... 32

Locking proﬁ les ..................................................... 33

SOUND Adjustment ................................................ 35

SDI SOUND OUTPUT ........................................... 35

PRESENT TIME SETUP / SET UP TIMER .............. 36

PRESENT TIME SETUP ....................................... 36

SET UP TIMER ..................................................... 36

SCREENSAVER (For preventing image retention)

Setup of SCREENSAVER Time ............................ 38

Reduces screen image retention ...............................39

EXTENDED LIFE SETTINGS ............................... 39

.. 37

Reduces power consumption ............................... 42

Customizing the Input labels ................................. 43

Selecting the On-Screen Menu Language ............ 43

DISPLAY ORIENTATION ......................................... 44

SET UP for MULTI DISPLAY ................................... 45

How to setup MULTI DISPLAY .............................. 45

ID Remote Control Function .................................. 46

MULTI PIP SETUP ................................................... 47

SET UP for PORTRAIT ........................................... 48

How to setup PORTRAIT ...................................... 48

SET UP for Input Signals ....................................... 50

COMPONENT / RGB IN SELECT ......................... 50

YUV / RGB IN SELECT ......................................... 50

SIGNAL menu ....................................................... 51

3D Y/C FILTER ...................................................... 51

COLOR SYSTEM / Panasonic AUTO ................... 52

3:2 PULLDOWN .................................................... 52

XGA MODE ........................................................... 52

REFRESH RATE ................................................... 53

NOISE REDUCTION ............................................. 53

SYNC .................................................................... 54

SDI THROUGH ..................................................... 54

Input signal display ................................................ 54

Options Adjustments ............................................. 55

Weekly Command Timer ....................................... 58

Shipping condition ................................................. 59

Troubleshooting ..................................................... 60

List of Aspect Modes ............................................. 61

Applicable input signals ........................................ 62

Command list of Weekly Command Timer ........... 64

Speciﬁ cations ......................................................... 65

Panasonic Professional Flat Panel Display

Limited Warranty .................................................... 66

LIMITED WARRANTY STATEMENT ....................... 67

Customer Service ................................................... 68

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced technician for help.

This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC CAUTION: To assure continued compliance, follow the attached installation instructions and use only shielded interface cables when connecting to computer or peripheral devices. Any changes or modiﬁ cations not expressly approved by Panasonic Corp. of North America could void the user's authority to operate this device.

FCC Declaration of Conformity

Model No. TH-85PF12U

Responsible Party: Panasonic Corporation of North America One Panasonic Way 1F-10, Secaucus, NJ 07094 Contact Source: Panasonic Professional Display Company Panasonic Plasma Concierge 1-800-973-4390

CANADIAN NOTICE:

This Class B digital apparatus complies with Canadian ICES-003.

Note:

Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.

Trademark Credits

• VGA is a trademark of International Business Machines Corporation.

• Macintosh is a registered trademark of Apple Inc. USA.

• SVGA, XGA, SXGA and UXGA are registered trademarks of the Video Electronics Standard Association. Even if no special notation has been made of company or product trademarks, these trademarks have been fully

respected.

• HDMI, the HDMI logo and High-Deﬁ nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Safety Precautions

CAUTION

This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury.

• Pedestal .................................................................. TY-ST85P12

• Floor stand .............................................................. TY-ST85PF12

• Wall-hanging bracket (vertical) ................................ TY-WK85PV12

• Ceiling-haging bracket ............................................ TY-CE85PS12

• BNC Component Video Terminal Board .................. TY-42TM6A

• BNC Composite Video Terminal Board ................... TY-42TM6B

• BNC Dual Video Terminal Board ............................. TY-FB9BD

• RCA Component Video Terminal Board .................. TY-42TM6Z

• RCA Composite Video Terminal Board ................... TY-42TM6V

• RGB Active Through Terminal Board ...................... TY-42TM6G

• PC Input Terminal Board ......................................... TY-42TM6P

•

Composite / Component Video Terminal Board

• BNC SDI Terminal Board ........................................ TY-FB7SD

• HD-SDI Terminal Board .......................................... TY-FB9HD

• HD-SDI Terminal Board with audio ......................... TY-FB10HD

• Dual Link HD-SDI Terminal Board ........................... TY-FB11DHD

• HDMI Terminal Board .............................................. TY-FB8HM

• Dual HDMI Terminal Board ..................................... TY-FB10HMD

• DVI-D Terminal Board ............................................. TY-FB11DD

• Ir Through Terminal Board ...................................... TY-FB9RT

• Wireless Presentation Board .................................. TY-FB10WPU

• AV Terminal Box ...................................................... TY-TB10AV

• LAN Control Board .................................................. TY-FB12LC

(All of the following accessories are manufactured by Panasonic Corporation.)

................ TY-42TM6Y

Always be sure to ask a qualiﬁ ed technician to carry out set-up.

Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from being played with by young children, creating the potential risk of suffocation.

When using the Plasma Display

Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.

•

Top of the Plasma Display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries can happen if any body parts are brought too close. Placing any object near the top of the display could also result in heat damages to the object as well as to the Display if its ventilation holes are blocked.

Be sure to disconnect all cables before moving the Plasma Display.

•

Moving the Display with its cables attached might damage the cables which, in turn, can cause ﬁ re or electric shock.

Disconnect the power plug from the wall outlet as a safety precaution before carrying out any cleaning.

• Electric shocks can result if this is not done.

Clean the power cable regularly to prevent it from becoming dusty.

• Built-up dust on the power cord plug can increase humidity which might damage the insulation and cause ﬁ re. Unplug the cord from the wall outlet and clean it with a dry cloth.

This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment. Install your infrared sensor in a place away from direct or reﬂ ected light from your Plasma Display.

Note:

Safety Precautions / Maintenance

WARNING

Setup

Do not place the Plasma Display on sloped or unstable surfaces.

• The Plasma Display may fall off or tip over.

Do not place any objects on top of the Plasma Display.

•

If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in ﬁ re or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center.

Do not cover the ventilation holes.

• Doing so may cause the Plasma Display to overheat, which can cause ﬁ re or damage to the Plasma Display.

Transport only in upright position!

• Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry.

If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, and

6.0” (15 cm) or more at the rear, and also keep the space between the bottom of the display and the ﬂ oor surface. If using some other setting-up method, follow the manual of it. (If there is no speciﬁ c indication of installation dimension in the installation manual, leave a space of 3 15/16” (10 cm) or more at the top, bottom, left and right, and 6.0” (15 cm) or more at the rear.)

An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing connection.

AC Power Supply Cord

The Plasma Display is designed to operate on 120 V AC, 50/60 Hz.

Ensure that the mains plug is easily accessible.

Securely insert the power cord plug as far as it will go.

• If the plug is not fully inserted, heat may be generated which could cause ﬁ re. If the plug is damaged or the wall socket plate is loose, they should not be used.

Do not handle the power cord plug with wet hands.

• Doing so may cause electric shocks.

Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable.

• Do not make any modiﬁ cations, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the power cable. Doing so may cause damage to the power cable which can cause ﬁ re or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center.

If the Plasma Display will not be used for a long period of time, unplug the power cord from the wall outlet.

If problems occur during use

If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately.

• Continuous use of the Display under these conditions might cause ﬁ re or permanent damage to the unit. Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature.

If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately.

• A short may occur, which could cause ﬁ re. Contact an Authorized Service Center for any repairs that need to be made.

Maintenance

The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.

• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry.

• Do not scratch or hit the surface of the panel with ﬁ ngernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.

If the cabinet becomes dirty, wipe it with a soft, dry cloth.

• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.

• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result.

• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

Accessories

Accessories Supplied

Check that you have the Accessories and items shown

Operating Instruction book

Allen wrench

Remote Control Transmitter EUR7636070R

Eyebolt cap × 1 Eyebolt × 1 Blind sheet × 1 Clamper × 1

Remote Control Batteries

Requires two AA batteries.

1. Pull and hold the hook, then open the battery cover.

2. Insert batteries - note correct polarity ( + and -).

Batteries for the Remote Control Transmitter (AA Size × 2)

3. Replace the cover.

Fixing bands × 2

Used to attach the optional LAN Control Board (TY-FB12LC). For details, refer to the operating instructions for the board.

“AA” size

Helpful Hint:

For frequent remote control users, replace old batteries with Alkaline batteries for longer life.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Disposal of batteries should be in an environment-friendly manner.

Observe the following precautions:

1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.

2. Do not combine a used battery with a new one.

3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

5. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display.

6. Do not burn or breakup batteries. Batteries must not be exposed to excessive heat such as sunshine, ﬁ re or the like.

Connections

AUDIO OUT Terminals connection

AC cord connection (see page 13)

– How to Unfasten the AC cord

Loosen the ﬁ xing band securing the AC cord.

To loosen: Push the catch

R L

AUDIO OUT

Stereophonic sound code

audio equipment

line-in

Pull

– Cable ﬁ xing bands

Secure any excess cables with bands as required.

Note:

Two ﬁ xing bands are supplied with this unit. In case of securing cables at three positions, please purchase it separately.

Pass the attached cable ﬁ xing band through the clip as shown in the ﬁ gure.

SLOT1 SLOT3

To secure cables connected to Terminals, wrap the cable ﬁ xing band around them then pass the pointed end through the locking block, as shown in the ﬁ gure.

While ensuring there is sufﬁ cient slack in cables to minimize stress (especially in the power cord), ﬁ rmly bind all cables with the supplied ﬁ xing band.

To loosen: Push the catch

AUDIO

Pull

SERIAL PC IN

R L

AUDIO OUT

SLOT2

To tighten:

Pull

AUDIO

R L

P R /C R /R P B /C B /B

COMPONENT/RGB IN

Y/G

Optional Terminal Board Insert Slot (covered)

Dual HDMI Terminals (equivalent of Dual HDMI Terminal Board (TY-FB10HMD)) (see page 12)

COMPONENT/RGB IN and Audio IN Terminals (equivalent of BNC Component Video Terminal Board (TY-42TM6A)) (see page 12)

From EXTERNAL monitor terminal on Computer (see page 10)

Note: At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3.

From SERIAL Terminal on Computer (see page 11)

From input on audio ampliﬁ er (see page 9)

Connections

PC Input Terminals connection

COMPUTER

Conversion adapter (if necessary)

RGB

PC cable

(Female)

AUDIO

PC IN

Mini D-sub 15p

(Male)

Audio

Connect a cable which matches the audio output terminal on the computer.

Stereo plug

Notes:

• With regard to the typical PC input signals that are described in the applicable input signals list (see page 62), adjustment values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight PC input signal types that are not included in the list.

• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

• The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080 dots when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show ﬁ ne detail with sufﬁ cient clarity.

• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

• Some PC models cannot be connected to the set.

• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

• The computer shown in the illustration is for example purposes only.

• Additional equipment and cables shown are not supplied with this set.

• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speciﬁ ed frequency range.

• Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.

• Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT”

(when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 50)

Signal Names for Mini D-sub 15P Connector

Pin No.

4 5

15 14 13 12 11

6 7 8

Pin Layout for PC Input Terminal

NC (not connected)

Signal Name

R (PR/CR)

G (Y)

B (PB/CB)

GND (Ground)

Pin No.

Signal Name

GND (Ground) GND (Ground) GND (Ground)

+5 V DC

GND (Ground)

Pin No.

Signal Name

NC (not connected)

SDA

HD/SYNC

SCL

SERIAL Terminals connection

The SERIAL terminal is used when the Plasma Display is controlled by a computer.

COMPUTER

(Male)

Connections

1 3 4 5 2

6 7 8 9

RS-232C Straight cable

D-sub 9p

Notes:

• Use the RS-232C straight cable to connect the computer to the Plasma Display.

• The computer shown is for example purposes only.

• Additional equipment and cables shown are not supplied with this set.

The SERIAL terminal conforms to the RS-232C interface speciﬁ cation, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisﬁ es the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details.

Communication parameters

Signal level RS-232C compliant

Synchronization method Asynchronous

Baud rate 9600 bps

Parity None

Character length 8 bits

Stop bit 1 bit

Flow control -

Basic format for control data

The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent.

STX C1 C2 C3 P1 P2 P3 P4: P5 ETX

Start (02h)

Colon Parameter(s) 3-character command (3 bytes)

(1 - 5 bytes)

End (03h)

Notes:

• If multiple commands are transmitted, be sure to wait for the response for the ﬁ rst command to come from this unit before sending the next command.

• If an incorrect command is sent by mistake, this unit will send an “ER401” command back to the computer.

• SL1A, SL1B, SL2A and SL2B of Command IMS are available only when a dual input terminal board is attached.

SERIAL

Pin layout for SERIAL Terminal

(Female)

Signal names for D-sub 9P connector

Pin No.

2 3 5

•

7 8

•

Details

R X D T X D

GND

Non use

(Shorted in this set)

These signal names are those of computer speciﬁ cations.

Command

Command Parameter Control details PON None Power ON POF None Power OFF AVL ** Volume 00 - 63 AMT 0 Audio MUTE OFF

1 Audio MUTE ON

IMS None

SL1 SL2 SL3 PC1 SL1A SL1B SL2A SL2B

DAM None

ZOOM FULL JUST NORM SELF SJST SNOM SFUL ZOM2

Input select (toggle) Slot1 input Slot2 input Slot3 input PC input Slot1 input (INPUT1A) Slot1 input (INPUT1B) Slot2 input (INPUT2A) Slot2 input (INPUT2B)

Screen mode select (toggle) ZOOM (For Video/SD/PC signal) FULL JUST (For Video/SD signal) 4:3 (For Video/SD/PC signal) Panasonic Auto (For Video signal) JUST (For HD signal) 4:3 (For HD signal) H-FILL (For HD signal)

ZOOM (For HD signal)

With the power off, this display responds to PON command only.

COMPO

Connections

HDMI connection

This unit has terminal boards equivalent to Dual HDMI Terminal Board (TY-FB10HMD) and BNC Component Video Terminal Board (TY-42TM6A) as standard equipment.

[Pin assignments and signal names]

Pin No.

3 4

6 7

Signal

T.M.D.S Data2+

T.M.D.S Data2 Shield

T.M.D.S Data2T.M.D.S Data1+ T.M.D.S Data1

Shield T.M.D.S Data1T.M.D.S Data0+ T.M.D.S Data0

Shield T.M.D.S Data0T.M.D.S Clock+

Pin No.

15 16

18 19

Signal

T.M.D.S Clock Shield

T.M.D.S Clock-

CEC

Reserved (N.C. on device)

SCL SDA DDC/CEC

Ground +5V Power Hot Plug Detect

AUDIO

SLOT1 SLOT2 SLOT3

PR/CR/R PB/CB/B

COMPONENT/RGB IN

HDMI cables

Y/G

3 1

Note:

Additional equipment and HDMI cables shown are not supplied with this set.

COMPONENT / RGB connection

NEN T VIDEO OUT

B , P R ,

OUT

P B

Example of input signal source

DVD

Digital TV-SET-TOP-BOX (DTV-STB)

Y , P

OUT

AUDIO

HDMI

AV OUT

HDMI

AV OUT

DVD player DVD player

RCA-BNC adapter plug

AUDIO

PR/CR/R PB/CB/B

COMPONENT/RGB IN

SLOT3

Computer RGB Camcorder

Notes:

• Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” (when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 50)

• Additional equipment, cables and adapter plugs shown are not supplied with this set.

• SYNC ON G signal is needed. (see page 54)

Y/G

Power ON / OFF

Connecting the plug to the Wall Outlet.

Press the Power switch on the Plasma Display to turn the set on: Power-On.

Power Indicator: Green

Right side surface

Main Power On / Off Switch

Remote Control Sensor

Press the button on the remote control to turn the Plasma Display off.

Power Indicator: Red (standby)

Press the button on the remote control to turn the Plasma Display on.

Power Indicator: Green

Turn the power to the Plasma Display off by pressing the switch on the unit, when the Plasma Display is on or in standby mode.

Note:

During operation of the power management function, the power indicator turns orange in the power off state.

Power Indicator

Power ON / OFF

When ﬁ rst switching on the unit

Following screen will be displayed when the unit is turned on for the ﬁ rst time. Select the items with the remote control. Unit buttons are invalid.

OSD LANGUAGE

Select the language.

Set.

OSD LANGUAGE

English (UK)

Deutsch

Français

Italiano

Español

ENGLISH (US)

Русский

PRESENT TIME SETUP

Select “DAY” or “PRESENT TIME OF DAY”.

Setup “DAY” or “PRESENT TIME OF DAY”.

Select “SET”.

Set.

PRESENT TIME SETUP

PRESENT TIME OF DAY MON 99:99

SET DAY PRESENT TIME OF DAY

PRESENT TIME SETUP

PRESENT TIME OF DAY MON 99:99

SET DAY PRESENT TIME OF DAY

DISPLAY ORIENTATION

For vertical installation, select “PORTRAIT”.

Set.

DISPLAY ORIENTATION

LANDSCAPE

PORTRAIT

Notes:

• Once the items are set, the screens won't be displayed when switching on the unit next time.

• After the setting, the items can be changed in the following menus. OSD LANGUAGE (see page 43) PRESENT TIME SETUP (see page 36) DISPLAY ORIENTATION (see page 44)

SET SELECT

MON 99:99

TUE

10:00

From the second time on, the below screen is displayed for a while (setting condition is an example).

NANODRIFT HIGH MID

FULL

Selecting the input signal

Select the input signals to be connected by installing the optional Terminal Boards.

Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display.

Input signals will change as follows:

INPUT1

SLOT2 is for dual input so that you can select INPUT2A or INPUT2B for INPUT2. INPUT2A : HDMI signal terminal in SLOT2 INPUT2B : HDMI signal terminal in SLOT2

INPUT2A

INPUT2B

PCINPUT3

Press the INPUT “1”, “2”, “3” or “PC” input mode selection button to select the INPUT mode. Press to switch the input mode between INPUT2A and INPUT2B.

Notes:

• Selecting is also possible by pressing the INPUT button on the unit.

• Input terminal will not be selected if the terminal board is not installed into the SLOT.

• Select to match the signals from the source connected to the component/RGB input terminals. (see page 50)

• In 2 screen display, the same input mode cannot be selected for the main picture and sub picture.

• Image retention (image lag) may occur on the plasma display panel when a still picture is kept on the panel for an extended period. The function that darkens the screen slightly is activated to prevent image retention (see page 60), but this function is not the perfect solution to image retention.

ENTER /

VOL

INPUT

Basic Controls

Main Unit

Remote control sensor

Power Indicator

The Power Indicator will light.

• Power-OFF ...... Indicator not illuminated

(The unit will still consume some power as long as the power cord is still inserted into the wall outlet.)

• Standby ........... Red

Orange (When “Slot power” is set to “On”. See page 57) Orange (Depending on the type of the function board installed, when the power is supplied to the slot)

• Power-ON ........ Green

• DPMS (POWER MANAGEMENT)

................... Orange (With PC input signal.

See page 42)

Right side

surface

ENTER/

+ /

VOL

INPUT

Enter / Aspect button

(see page 18, 23)

Volume Adjustment

Volume Up “+” Down “–” When the menu screen is displayed: “+” :

press to move the cursor up

“–” :

press to move the cursor down

(see page 23)

MENU Screen ON / OFF

Each time the MENU button is pressed, the menu screen will switch. (see page 23)

Normal Viewing PICTURE SETUP

SOUND POS. /SIZE

INPUT button (INPUT signal selection)

(see page 15)

Main Power On / Off Switch

Remote Control Transmitter

R button (see page 23)

Press the R button to return to previous menu screen.

Standby (ON / OFF) button

The Plasma Display must ﬁ rst be plugged into the wall outlet and turned on at the power switch (see page 13). Press ON to turn the Plasma Display On, from Standby mode. Press OFF to turn the Plasma Display Off to Standby mode.

N button (see page 27, 28, 29, 35)

POSITION buttons

ACTION button

Press to make selections.

POS. /SIZE button

(see page 25)

PICTURE button (see page 28)

INPUT button

Press to select INPUT1, INPUT2, INPUT3 and PC input SLOTS sequentially. (see page 15) When a dual input terminal board is attached, A or B is displayed depending on the selected input signal. (Ex. INPUT1A, INPUT1B)

Sound mute On / Off Press this button to mute the sound. Press again to reactivate sound. Sound is also reactivated when power is turned off or volume level is changed.

Numeric buttons (see page 46)

ASPECT button

Press to adjust the aspect. (see page 18)

SURROUND button

The surround setting switches on and off each time the SURROUND button is pressed. The beneﬁ ts of surround sound are enormous. You can be completely enveloped in sound; just as if you were at a concert hall or cinema.

ON OFF

SURROUND

Basic Controls

Status button

Press the “Status” button to display the current system status.

Input label

NANODRIFT setting value (see page 40)

Aspect mode (see page 18)

Off timer

The off timer indicator is displayed only when the off timer has been set.

Clock display (see page 57)

NANODRIFT HIGH MID

4:3

10:00

OFF TIMER 90

SET UP button (see page 23)

SOUND button (see page 35)

DIRECT INPUT buttons

Press the INPUT “1”, “2”, “3” or “PC” input mode selection button to select the INPUT mode. (see page 15) This button is used to switch directly to INPUT mode.

Channel Adjustment

This button cannot be used for this model.

Volume Adjustment

Press the Volume Up “+” or Down “–” button to increase or decrease the sound volume level.

OFF TIMER button

The Plasma Display can be preset to switch to stand-by after a ﬁ xed period. The setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed.

30 60

When three minutes remain, “OFF TIMER 3” will ﬂ ash. The off timer is cancelled if a power interruption occurs.

Remote ID lock (see page 46)

Digital Zoom (see page 22)

MULTI Window buttons

(see page 19)

ASPECT Controls

The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture.

Note:

Be aware that if you put the display in a public place for commercial purposes or a public showing and then use the aspect mode select function to shrink or expand the picture, you may be violating the copyright under copyright law. It is prohibited to show or alter the copyrighted materials of other people for commercial purposes without the prior permission of the copyright holder.

Press repeatedly to move through the aspect options: For details about the aspect mode, please see “List of Aspect Modes” (page 61).

For VIDEO (S VIDEO) signal input:

[from the unit]

Right side surface

ENTER/

VOL

For PC signal input:

4:3 ZOOM FULL 4:3 ZOOM JUSTFULL

4:3 ZOOM Panasonic AUTO

JUST FULL

Note:

When selecting an input slot that attaches BNC Dual Video Terminal Board (TY-FB9BD), Panasonic AUTO cannot be selected.

The aspect mode changes each time the ENTER button is pressed.

For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p):

For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]:

4:3 H-FILL ZOOM

[During MULTI PIP Operations]

• Picture and Picture, Picture in Picture :

FULL JUST

4:3 FULL

• Others : Aspect switching is not possible.

Notes:

• Panasonic AUTO can be selected only during Video signal input.

• The aspect mode is memorized separately for each input terminal.

• Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent image retention to remain on the Plasma Display Panel.

Panasonic AUTO

The display will automatically become enlarged (depending on the picture source), allowing you to view the picture at its maximum size.

4 16

3 9

Panasonic AUTO

Notes:

• Panasonic AUTO mode is designed to automatically adjust the aspect ratio to handle a mix of 16:9 and 4:3 program material. Certain 4:3 program material, such as stock market data screens,

For letter box image Image is expanded

Changes in accordance with the Panasonic AUTO mode

setting (see page 52).

For a 4:3 image

may occasionally cause the image size to change unexpectedly. When viewing such programs, it is recommended that the ASPECT be set to 4:3.

• If adjusting the PICTURE V-POS/V-SIZE in Panasonic AUTO with FULL mode, the adjustment is not memorized. When exiting the mode, the screen will return to a former adjustment.

All Aspect mode

Set “All Aspect” to “On” in Options menu to enable the extended aspect mode (page 57). When All Aspect mode, the aspect mode of pictures is switched as follows. For details about the aspect mode, please see “List of Aspect Modes” (page 61).

For VIDEO (S VIDEO) signal input:

4:3 Zoom1 16:9 JustZoom2 Zoom3 Panasonic Auto 14:9

Notes:

When selecting an input slot that attaches BNC Dual Video Terminal Board (TY-FB9BD), Panasonic Auto cannot be selected.

•

• In All Aspect mode, “Panasonic AUTO” is displayed as “Panasonic Auto”.

For PC signal input:

4:3 Zoom 16:9

ASPECT Controls

For SD signal input (525 (480) / 60i

•

60p, 625 (575) / 50i

•

50p):

4:3 Zoom1 16:9 JustZoom2 Zoom3 14:9

For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]:

4:3 Full Zoom1 16:9 Just1Zoom2 Zoom3 14:9 Just2 4:3 (1) 4:3 (2)

MULTI PIP

You can display two pictures, such as a video image and computer image, in a two-screen display. (Use the remote control for this operation. It cannot be performed with the buttons on the main unit.)

MULTI PIP SETUP

Set the functions and mode for two-screen display in “MULTI PIP SETUP” in the SET UP menu. (see page 47)

Selecting the Display Mode

Note:

The screen changes in the same way when “DISPLAY MODE” in “MULTI PIP SETUP” is changed. (see page 47)

During PIP: During Advanced PIP:

Each time this button is pressed, the screen changes.

One screen Two screens (P AND P)

INPUT1

Main screen Sub screen

Two screens (P OUT P)Two screens (P IN P)

INPUT1

Main screen input mode

Sub screen input mode

One screen

Advanced PIP

Sub screen

1–

Main screen

Note:

and button operations are not available during

advanced PIP.

MULTI PIPMULTI PIP

During Blend PIP (Composite Screen Function) :

A composite picture is displayed with the sub screen positioned over the main screen. For example, text data such as a computer image can be displayed as a caption over a movie or still image.

One screen FULL P IN P

Transparent Function and Insertion Function

Two functions are available for blend PIP: the transparent function and the insertion function. Set these functions with “TRANSPARENCY” or “INSERT” in “MULTI PIP SETUP”. (see page 47)

Transparent Function

Data such as text are displayed transparently on the background image.

Note:

Be aware that if you put the display in a public place for commercial purposes or a public showing and then use the blend PIP function to make a composite screen display, you may be violating the copyright under copyright law. It is prohibited to show or alter the copyrighted materials of other people for commercial purposes without the prior permission of the copyright holder.

Insertion Function

The sub screen image is divided into transparent and nontransparent areas, and only the non-transparent areas are inserted and displayed on the background image.

Swapping Screens

Each time this button is pressed, the main screen and sub screen are swapped.

Two screens

(P AND P)

Two screens

(P OUT P)

Two screens

(P IN P)

Main screen Sub screen

Selecting the Target Screen for Operations

Each time this button is pressed, the target screen for operations changes.

MULTI PIP

Operations on

the main screen

INPUT1

Main screen Sub screen

Main screen input mode Sub screen input mode

Operations on the sub screen

INPUT1

Notes:

• When operations are performed for the sub screen, the sub screen audio is played.

• If no operations are performed, the operation target returns to the main screen after about 5 seconds*. You can also return to main screen operations by operating the remote control buttons (except for ). * It takes more than 5 seconds if a slot mounted with a Dual HDMI Terminal Board (TY-FB10HMD) is selected.

Selecting the Sub Screen Position (During P IN P Display)

Each time this button is pressed, the sub screen position changes.

Note:

Some sub screen positions may hide the display of the menu screen.

Notes:

• Do not use the two-screen display for a long time. It will cause a permanent image retention to remain on the screen.

• If “INPUT lock” in Options menu is set to other than “Off”, MULTI PIP function isn’t available.

• Sound output is from the picture which is selected in AUDIO OUT (PIP) (see page 35).

• In two-screen display, the same input mode cannot be selected for the main picture and sub picture.

• The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of the pictures. There may also be a difference in the picture quality of the sub picture depending on the type of signals displayed on the main picture and depending on the two-screen display mode.

• Due to the small dimensions of the sub pictures, these sub pictures cannot be shown in detail.

•

Computer screen picture is displayed in a simpliﬁ ed format, and it may not be possible to discern details on them satisfactorily.

•

Following combinations of two analog signals cannot be displayed simultaneously;

Component - Component, Component - PC (RGB), PC (RGB) - Component, PC (RGB) - PC (RGB)

•

2k1k signals that are received with the Dual Link HD-SDI Terminal Board (TY-FB11DHD) cannot be displayed in two-screen display.

Digital Zoom

This displays an enlargement of the designated part of the displayed image.

Display the operation guide.

Press to access Digital Zoom. The operation guide will be displayed.

During Digital Zoom, only the following buttons can be operated.

[Remote control]

POSITION / ACTION button

VOL button

MUTE button

SURROUND button OFF TIMER button

Select the area of the image to be enlarged.

Press on the enlargement location to select.

The cursor will move.

[Unit]

Right side surface

ENTER/

VOL

INPUT

VOL button

EXIT

Notes:

• When power goes OFF (including “Off Timer” operation), Digital Zoom terminates.

• The Digital Zoom function cannot be selected while in the following operation state: “Multi-viewer” (P AND P, P OUT P, P IN P) operation. (see page 19) When MULTI DISPLAY SETUP is ON (see page 45). When PORTRAIT SETUP is ON (see page 48). When SCREENSAVER (except for NEGATIVE IMAGE) is running. (see page 37)

• While Digital Zoom is in operation, “Adjusting POS. /SIZE” cannot be used.

Select the magniﬁ cation required for the enlarged display.

Each time this is pressed, the magniﬁ cation factor changes. This is shown in the image being displayed.

Return to normal display (quit Digital Zoom).

Press to exit from the Digital Zoom.

s1

s2

s3

s4

EXIT

+ 50 hidden pages