This manual is common to all the models regardless of suffixes of the
*
model number.
U : for US, Canada and Mexico
W : for EU, CIS, South East Asia and Middle East Asia
English
Please read these instructions before operating your set
and retain them for future reference.
DPQP1100ZA
Dear Panasonic Customer
Welcome to the Panasonic family of customers. We hope that
you will have many years of enjoyment from your new LCD
Display.
To obtain maximum benefit from your set, please read these
Instructions before making any adjustments, and retain them
for future reference.
Retain your purchase receipt also, and note down the model
number and serial number of your set in the space provided
on the rear cover of these instructions.
Visit our Panasonic Web Site http://panasonic.com
English
2
Table of Contents
Before use
●
Illustrations and screens in this Operating Instructions
are images for illustration purposes, and may be
different from the actual ones.
Important Safety Instructions ..........................4
WARNING: To reduce the risk of electric shock,
do not remove cover or back.
No user-serviceable parts inside. Refer servicing
to qualified service personnel.
The lightning flash with arrow-head within a
triangle is intended to tell the user that parts
inside the product are a risk of electric shock
to persons.
The exclamation point within a triangle
is intended to tell the user that important
operating and servicing instructions are in the
papers with the appliance.
WARNING :
To prevent damage which may result in fire or
shock hazard, do not expose this apparatus to
rain or moisture.
Do not place containers with water (flower vase,
cups, cosmetics, etc.) above the set.
(including on shelves above, etc.)
WARNING :
1) To prevent electric shock, do not remove cover. No
user serviceable parts inside. Refer servicing to
qualified service personnel.
2) Do not remove the grounding pin on the power
plug. This apparatus is equipped with a three pin
grounding-type power plug. This plug will only fit
a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the
outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.
Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The
wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments / accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart / apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15) To prevent electric shock, ensure the grounding pin
on the AC cord power plug is securely connected.
English
4
FCC STATEMENT
This equipment has been tested and found to comply
with the limits for a class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
FCC CAUTION:
To assure continued compliance, follow the attached
installation instructions and use only the provided
power supply cord and DVI interface cable. Any
changes or modifications not expressly approved
by Panasonic Corp. of North America could void the
user’s authority to operate this device.
Declaration of Verification
Model No.
TH-55VF1HU
Responsible Party:
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, New Jersey
07102-5490
Contact Source:
Panasonic System Communications Company of
North America
1-877-655-2357
General Contact:
http://shop.panasonic.com/support
This device complies with Part 15 of the FCC Rules and
all applicable IC RSS standards. Operation is subject
to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must
accept any interference received, including interference
that may cause undesired operation.
CANADIAN NOTICE:
This Class A digital apparatus complies with
Canadian ICES-003.
WARNING:
Not for use in a computer room as defined in the
•
Standard for the Protection of Electronic Computer/
Data Processing Equipment, ANSI/NFPA 75.
For permanently connected equipment, a readily
•
accessible disconnect device shall be incorporated
in the building installation wiring.
For pluggable equipment, the socket-outlet shall
•
be installed near the equipment and shall be easily
accessible.
Note:
Image retention may occur. If you display a still
picture for an extended period, the image might
remain on the screen. However, it will disappear when
a general moving picture is displayed for a while.
Trademark Credits
Microsoft, Windows and Internet Explorer are the
•
registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other
countries.
Macintosh, Mac, Mac OS, OS X and Safari are the
•
trademarks of Apple Inc. registered in the United
States and other countries.
PJLink is a registered or pending trademark in Japan,
•
the United States, and other countries and regions.
HDMI, the HDMI Logo, and High-Definition
•
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United
States and other countries.
JavaScript is a registered trademark or a trademark of
•
Oracle Corporation and its subsidiary and associated
companies in the United States and/or other
countries.
RoomView, Crestron RoomView and Fusion RV are
•
registered trademarks of Crestron Electronics, Inc.
Crestron Connected is the trademark of Crestron
Electronics, Inc.
Even if no special notation has been made of company
or product trademarks, these trademarks have been fully
respected.
English
5
Important Safety
Notice
WARNING
1) To prevent damage which may result in fire or
shock hazard, do not expose this appliance to
dripping or splashing.
Do not place containers with water (flower vase,
cups, cosmetics, etc.) above the set. (including on
shelves above, etc.)
No naked flame sources, such as lighted candles,
should be placed on / above the set.
2) To prevent electric shock, do not remove cover. No
user serviceable parts inside. Refer servicing to
qualified service personnel.
3) Do not remove the earthing pin on the power
plug. This apparatus is equipped with a three pin
earthing-type power plug. This plug will only fit an
earthing-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet,
contact an electrician.
Do not defeat the purpose of the earthing plug.
4) To prevent electric shock, ensure the earthing pin
on the AC cord power plug is securely connected.
CAUTION
This appliance is intended for use in environments
which are relatively free of electromagnetic fields.
Using this appliance near sources of strong
electromagnetic fields or where electrical noise may
overlap with the input signals could cause the picture
and sound to wobble or cause interference such as
noise to appear.
To avoid the possibility of harm to this appliance, keep
it away from sources of strong electromagnetic fields.
IMPORTANT INFORMATION
If a display is not positioned in a sufficiently stable
location, it can be potentially hazardous due to falling.
Many injuries, particularly to children, can be avoided
by taking simple precautions such as:
Using cabinets or stands recommended by the
•
manufacturer of the display.
Only using furniture that can safely support the
•
display.
Ensuring the display is not overhanging the edge
•
of the supporting furniture.
Not placing the display on tall furniture (for
•
example, cupboards or bookcases) without
anchoring both the furniture and the display to a
suitable support.
Not standing the displays on cloth or other
•
materials placed between the display and
supporting furniture.
Educating children about the dangers of climbing
•
on furniture to reach the display or its controls.
WARNING:
This equipment is compliant with Class A of CISPR32.
In a residential environment this equipment may
cause radio interference.
English
6
IMPORTANT: THE MOULDED PLUG
FOR YOUR SAFETY, PLEASE READ THE
FOLLOWING TEXT CAREFULLY.
This display is supplied with a moulded three pin
mains plug for your safety and convenience. A 10
amp fuse is fitted in this plug. Shall the fuse need to
be replaced, please ensure that the replacement fuse
has a rating of 10 amps and that it is approved by
ASTA or BSI to BS1362.
Check for the ASTA mark
the body of the fuse.
If the plug contains a removable fuse cover, you must
ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used
until a replacement cover is obtained.
A replacement fuse cover can be purchased from
your local Panasonic dealer.
Do not cut off the mains plug.
Do not use any other type of mains lead except the
one supplied with this display.
The supplied mains lead and moulded plug are
designed to be used with this display to avoid
interference and for your safety.
If the socket outlet in your home is not suitable, get it
changed by a qualified electrician.
If the plug or mains lead becomes damaged,
purchase a replacement from an authorized dealer.
WARNING : — THIS DISPLAY MUST BE EARTHED.
How to replace the fuse.
Open the fuse compartment with a screwdriver and
replace the fuse.
or the BSI mark on
Safety Precautions
WARNING
■ Setup
This LCD Display is for use only with the following
optional accessories.
Use with any other type of optional accessories may
cause instability which could result in the possibility
of injury.
(All of the following accessories are manufactured by
Panasonic Corporation.)
Installation Mount
•
TY-VK55LV1
Cover-frame Kit
•
TY-CF55VW1
Early Warning Software
•
ET-SWA100 series
Video Wall Manager
•
TY-VUK10
1: Suffix of the part number may differ depending on
*
the license type.
2: Supports Ver1.4 or later.
*
Note
●
The part number of the optional accessories are
subject to change without notice.
We are not responsible for any product damage, etc.
caused by failures in the installation environment even
during the warranty period.
Always be sure to ask a qualified technician to carry out
set-up.
Small parts can present choking hazard if accidentally
swallowed. Keep small parts away from young children.
Discard unneeded small parts and other objects,
including packaging materials and plastic bags/sheets to
prevent them from being played with by young children,
creating the potential risk of suffocation.
Do not place the Display on sloped or unstable
surfaces, and ensure that the Display does not hang
over the edge of the base.
The Display may fall off or tip over.
•
Install this unit at a location with minimal vibration
and which can support the weight of the unit.
Dropping or falling of the unit may cause injury or
•
malfunction.
Do not place any objects on top of the Display.
If foreign objects or water get inside the Display, a
•
short-circuit may occur which could result in fire or
electric shock. If any foreign objects get inside the
Display, please consult your local Panasonic dealer.
Transport only in upright position!
Transporting the unit with its liquid crystal panel
•
facing upright or downward may cause damage to the
internal circuitry.
1
*
2
*
English
7
Ventilation should not be impeded by covering
the ventilation openings with items such as
newspapers, table cloths and curtains.
For sufficient ventilation, see page 10.
Caution - For use only with UL Listed Wall Mount
Bracket with minimum weight/load 25.0 kg (56.0 lbs).
When installing the Display vertically, rotate
clockwise and be sure that the Power Indicator
comes to the downside.
(The Power Indicator is situated at the back.)
90
Heat is generated and it may cause fire or damage to
the Display.
Installation should be performed by installation
professionals.
Installing the Display incorrectly may lead to an accident
that results in death or serious injury.
Specified Installation Mount (Optional) or a mounting
•
bracket that conform to VESA standards (VESA 400 ×
400) must be used. (see page 10)
Before installation, be sure to check if the mounting
•
location has enough strength to support the weight
of the LCD display and the wall hanging bracket for
anti drop.
If you terminate the use of the Display, ask
•
professionals to remove the Display as soon as
possible.
When mounting the Display on the wall, prevent the
mounting screws and power cable from contacting
metal objects inside the wall.
An electric shock may occur if they contact metal objects
inside the wall.
Do not place the display where it may be affected by
salt or corrosive gas.
Doing so may cause the display to fall due to
•
corrosion. Also, the unit may malfunction.
Do not install the product to a place where the
product is exposed to direct sunlight.
If the screen is exposed to direct sunlight, the liquid
•
crystal panel may have adverse effect.
■ When using the LCD Display
The Display is designed to operate on 110 ‒ 127 or
220 ‒ 240 V AC, 50/60 Hz.
Do not cover the ventilation holes.
Doing so may cause the Display to overheat, which
•
can cause fire or damage to the Display.
Do not stick any foreign objects into the Display.
Do not insert any metal or flammable objects into the
•
ventilations holes or drop them onto the Display, as
doing so can cause fire or electric shock.
Do not remove the cover or modify it in any way.
High voltages which can cause severe electric shocks
•
are present inside the Display. For any inspection,
adjustment and repair work, please contact your local
Panasonic dealer.
Ensure that the mains plug is easily accessible.
The mains plug shall be connected to a mains
socket outlet with a protective earthing connection.
Do not use any power supply cord other than that
provided with this unit.
Doing so may cause short-circuit, generates heat,
•
etc., which could cause electric shock or fire.
Do not use the supplied power supply cord with any
other devices.
Doing so could cause electric shock or fire.
•
Securely insert the power supply plug as far as it
will go.
If the plug is not fully inserted, heat may be generated
•
which could cause fire. If the plug is damaged or the
wall socket is loose, they shall not be used.
Do not handle the power supply plug with wet
hands.
Doing so may cause electric shocks.
•
Do not do anything that may damage the power
cable. When disconnecting the power cable, pull on
the plug body, not the cable.
Do not damage the cable, make any modifications
•
to it, place heavy objects on top of it, heat it, place it
near any hot objects, twist it, bend it excessively or
pull it. To do so may cause fire and electric shock. If
the power cable is damaged, have it repaired at your
local Panasonic dealer.
Do not touch the power supply cord or the plug
directly by hand when they are damaged.
Electric shock could occur.
•
Do not remove covers and NEVER modify the
Display yourself
Do not remove the rear cover as live parts are
•
accessible when it is removed. There are no user
serviceable parts inside. (High-voltage components
may cause serious electrical shock.)
Have the Display checked, adjusted, or repaired at
•
your local Panasonic dealer.
Keep the supplied AAA/R03/UM4 batteries out of
reach of children. If accidentally swallowed, it will be
harmful to the body.
Please contact a doctor immediately in case you
•
doubt that the child may have swallowed it.
English
8
If the Display is not going to be used for any
prolonged length of time:
Unplug the power supply plug from the wall outlet.
•
The power consumption is 0 W when the power
•
is turned off with the <Main power switch> on the
display. However, the power consumption is 0.5 W
when the power is turned off with the remote control
or <Power button (Unit)>. (see page 30)
Picture noise may occur if you connect / disconnect
the connection cables of the input terminals you
are currently not watching, or if you turn the power
of the video equipment on / off, but it is not a
malfunction.
To prevent the spread of fire, keep
candles or other open flames away from
this product at all times.
CAUTION
If problems or malfunction occur, stop using
immediately.
■ If problems occur, unplug the power supply
plug.
Smoke or an abnormal odour come out from the unit.
•
No picture appears or no sound is heard,
•
occasionally.
Liquid such as water or foreign objects got inside the
•
unit.
The unit has deformed or broken parts.
•
If you continue to use the unit in this condition, it
could result in fire or electric shock.
Turn the power off immediately, unplug the power
•
supply plug from the wall outlet, and then contact the
dealer for repairs.
To cut off the power supply to this Display completely,
•
you need to unplug the power supply plug from the
wall outlet.
Repairing the unit yourself is dangerous, and shall
•
never be done.
To enable to unplug the power supply plug
•
immediately, use the wall outlet which you can reach
easily.
■ Do not touch the unit directly by hand when
it is damaged.
Electric shock could occur.
■ When using the LCD Display
Do not bring your hands, face or objects close to the
ventilation holes of the Display.
Heated air comes out from the ventilation holes at the
•
top of Display will be hot. Do not bring your hands or
face, or objects which cannot withstand heat, close to
this port, otherwise burns or deformation could result.
At least 2 people are required to carry or unpack
this unit.
If this is not observed, the unit may drop, resulting in
•
injury.
Be sure to disconnect all cables before moving the
Display.
If the Display is moved while some of the cables are
•
still connected, the cables may become damaged,
and fire or electric shock could result.
Disconnect the power supply plug from the wall
socket as a safety precaution before carrying out
any cleaning.
Electric shocks can result if this is not done.
•
Clean the power cable regularly to prevent it
becoming dusty.
If dust built up on the power cord plug, the resultant
•
humidity can damage the insulation, which could
result in fire. Pull the power cord plug out from the
wall outlet and wipe the mains lead with a dry cloth.
English
9
Do not step on, or hang from the display.
They might tip over, or might be broken and it may
•
result in injury. Pay special attention to the children.
Do not reverse the polarity (+ and -) of the battery
when inserting.
Mishandling the battery may cause its explosion
•
or leakage, resulting in fire, injury or damage to
surrounding properties.
Insert the battery correctly as instructed. (see
•
page 13)
Remove the batteries from the remote control
transmitter when not using for a long period of time.
The battery may leak, heat, ignite or burst, resulting in
•
fire or damage to surrounding properties.
Do not burn or breakup batteries.
Batteries must not be exposed to excessive heat such
•
as sunshine, fire or the like.
Do not turn the Display upside down.
Do not position the unit with its liquid crystal panel
facing upright.
Precautions for use
Cautions when installing
Do not set up the Display outdoors.
The Display is designed for indoor use.
•
Environmental temperature to use this unit
When using the unit where it is below 1 400 m
•
(4 593 ft) above sea level: 0 °C to 40 °C (32 °F to
104 °F)
When using the unit at high altitudes (1 400 m
•
(4 593 ft) and higher and below 2 800 m (9 186 ft)
above sea level): 0 °C to 35 °C (32 °F to 95 °F)
Do not install the unit where it is 2 800 m (9 186 ft)
and higher above sea level.
Failure to do so may shorten the life of the internal
•
parts and result in malfunctions.
We are not responsible for any product damage, etc.
caused by failures in the installation environment
even during the warranty period.
Do not place the display where it may be affected by
salt or corrosive gas.
Failure to do so may shorten the life of the internal
•
parts and result in malfunctions due to corrosion.
Required space for ventilation
For the outermost periphery of the display, leave a
•
space of 10 cm (3.94”) or more at the top, bottom, left
and right.
At the rear, leave a space of 5 cm (1.97”) or more.
About the screws used for the mounting bracket that
conforms to VESA standards
Screw pitch for
installation
400 mm × 400 mm16.3 mmM6 (4)
Do not grab the liquid crystal panel.
Do not forcibly press the liquid crystal panel, or push
•
it with a pointed object. Applying a strong force to
the liquid crystal panel will cause unevenness of the
screen display, resulting in malfunction.
Depending on the temperature or humidity
conditions, uneven brightness may be observed.
This is not a malfunction.
This unevenness will disappear while applying current
•
continuously. If not, consult the distributor.
■ Note regarding security
When using this product, take safety measures
against the following incidents.
Personal information being leaked via this product
•
Unauthorized operation of this product by a malicious
•
third party
Interfering or stopping of this product by a malicious
•
third party
Depth of
screw hole
Screw
(quantity)
10
English
Take sufficient security measures. (see page 92, 94)
Set a password for the LAN control and restrict the
•
users who can log in.
Make your password difficult to guess as much as
•
possible.
Change your password periodically.
•
Panasonic Corporation or its affiliate companies will
•
never ask for your password directly. Do not divulge
your password in case you receive such inquiries.
The connecting network must be secured by a
•
firewall, etc.
When disposing the product, initialize the data before
•
disposing.
[Shipping] (see page 114 )
Cleaning and maintenance
The front of the liquid crystal panel has been
specially treated. Wipe the surface of the liquid
crystal panel gently using only a cleaning cloth or a
soft, lint-free cloth.
If the surface is particularly dirty, wipe with a soft,
•
lint-free cloth which has been soaked in pure water or
water in which neutral detergent has been diluted 100
times, and then wipe it evenly with a dry cloth of the
same type until the surface is dry.
Do not scratch or hit the surface of the panel with
•
fingernails or other hard objects, otherwise the
surface may become damaged. Furthermore, avoid
contact with volatile substances such as insect
sprays, solvents and thinner, otherwise the quality of
the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry
cloth.
If the cabinet is particularly dirty, soak the cloth in
•
water to which a small amount of neutral detergent
has been added and then wring the cloth dry. Use this
cloth to wipe the cabinet, and then wipe it dry with a
dry cloth.
Do not allow any detergent to come into direct contact
•
with the surface of the Display. If water droplets get
inside the unit, operating problems may result.
Avoid contact with volatile substances such as insect
•
sprays, solvents and thinner, otherwise the quality of
the cabinet surface may be adversely affected or the
coating may peel off. Furthermore, do not leave it for
long periods in contact with articles made from rubber
or PVC.
Usage of a chemical cloth
Do not use a chemical cloth for the panel surface.
•
Follow the instructions for the chemical cloth to use it
•
for the cabinet.
Wired LAN
When setting up the Display at a place, where
electric statistic occurs often, take a sufficient antistatic measure before start using.
When the Display is used at a location, where static
•
electricity occurs often, such as on a carpet, a wired
LAN communication is disconnected more often.
In that case, remove static electricity and the noise
source that may cause problems with an antistatic
mat, and re-connect the wired LAN.
In rare cases, the LAN connection is disabled due
•
to static electricity or noise. In that case, turn off the
power of the Display and the connected devices once
and then re-turn on the power.
The Display may not work properly due to strong
radio wave from the broadcast station or the radio.
If there is any facility or equipment, which outputs
•
strong radio wave, near the installation location, set
up the Display at a location sufficiently far from the
source of the radio wave. Or, wrap the LAN cable
connected to the LAN terminal by using a piece of
metal foil or a metal pipe, of which is grounded at
both ends.
Disposal
When disposing the product, ask your local
authority or dealer about the correct methods of
disposal.
English
11
Accessories
Accessories Supply
Check that you have the accessories and items shown
Operating Instructions
(CD-ROM × 1)
Power supply cord
(Approx. 2 m)
TH-55VF1HU
●
1JP155AF1U
TH-55VF1HW
●
1JP155AF1W
Remote Control Transmitter
× 1
●
N2QAYA000093
LAN cable (CAT5e) × 1
(Approx. 2 m)
●
TZZ00001774A
External IR Receiver × 1
(Approx. 1.8 m)
●
DPVF1180ZA
Batteries for the Remote
Control Transmitter
(AAA/R03/UM4 type × 2)
Clamper × 3
●
2JP155AF1W
●
3JP155AF1W
Attention
●
Store small parts in an appropriate manner, and keep
them away from young children.
●
In case you lost accessories, please consult your
dealer.
●
Dispose the packaging materials appropriately after
taking out the items.
12
English
Remote Control Batteries
1. Pull and hold the hook, then open the battery cover.
2. Insert batteries - note correct polarity (+ and -).
AAA/R03/UM4 type
VESA Mounting
To mount this Display using a VESA mounting bracket
(commercially available):
Protective Sheet
Table
3. Replace the cover.
Helpful Hint
●
For frequent remote control users, replace old
batteries with Alkaline batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage
and corrosion that will damage the remote control
transmitter.
Disposal of batteries should be in an environmentfriendly manner.
Observe the following precaution:
1. Batteries shall always be replaced as a pair. Always
use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with
“Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble,
heat or burn used batteries.
5. Battery replacement is necessary when remote
control acts sporadically or stops operating the
Display set.
6. Do not burn or breakup batteries.
7. Batteries must not be exposed to excessive heat such
as sunshine, fire or the like.
VESA Grid
1. Lay a protective sheet on a flat table, which was
wrapped around this Display when it was packaged,
beneath the screen surface so as not to scratch the
screen face.
2. Ensure you have all accessories for mounting this
Display.
3. Follow the instructions that came with the mounting
kit. Failing to follow the correct mounting procedures
could result in damage to the equipment, or injury to
the user or install personnel. The product warranty
does not cover the damage caused by improper
installation even during the warranty period.
English
13
Cautions when
LCD panel
moving
The display has handles for carrying. Hold them when
moving.
Handle
Note
●
Do not hold parts other than the handles.
●
At least 2 people are required to carry this unit.
If this is not observed, the unit may drop, resulting in
injury.
●
When carrying the unit, keep the liquid crystal panel
upright.
Carrying the unit with the surface of the liquid crystal
panel facing up or down may cause deformation of
the panel, or internal damage.
●
Do not hold the upper, lower, right and left frames or
the corners of the unit. Do not hold the front surface
of the liquid crystal panel. Also, do not hit such parts.
Doing so may damage the liquid crystal panel.
Also, the panel may crack, resulting in injury.
protection
Protection materials for the LCD panel have been
attached on this unit.
Remove one on the bottom surface before installation
and the other four on the front surface (left, right, top
and bottom) after installation.
Protection material (front surface)
Protection material (bottom surface)
14
English
Eyebolt
Kensington security
The display has holes for attaching eyebolts (M10).
When installing, use them to suspend the display.
Use the eyebolt only for temporary hanging or
movement.
Suspension and installation should be performed by
an installation professional.
●
Do not install the Display using only 1 eyebolt.
●
Use the eyebolt of size M10, which fulfils the load
condition of the mass of the product.
●
After installation, remove the eyebolts, and close the
holes using the eyebolt caps removed when attaching
the eyebolts.
The security slot of this unit is compatible with the
Kensington security cables.
English
15
Connections
AC cord connection and fixing
Back of the unit
AC cord fixing
AC cord (supplied)
Cable fixing
Note
●
3 clampers are supplied with this unit. Fix the cables
at 3 locations using the holes for clampers as shown
below.
If you need more clampers, purchase them from your
dealer. (Available from the customer service)
1. Attach the clamper
hole
Insert the clamper in a
hole.
Plug the connector into the display unit.
Plug the connector until it clicks.
Note
●
Make sure that the connector is locked on both the
left and right sides.
Unplug the AC cord
Unplug the connector pressing the two knobs.
Note
●
When disconnecting the AC cord, be absolutely sure
to disconnect the AC cord plug at the socket outlet
first.
●
The supplied AC cord set is for this unit exclusive use.
Do not use this for other purposes.
To remove from
the unit:
2. Bundle the cables
hooks
To loosen:
knob
snaps
Keep pushing both side
snaps and pull out the
clamper.
Set the tip in the hooks
and tighten.
Keep pushing the knob
and pull out the tip.
16
English
Video equipment connection
R/PR/CR
B/CB
B/P
COMPONENT/RGB/VIDEOIN
13
12
11
G/Y/VIDEO
1 SERIAL IN,
SERIAL OUT:
213 45678910
SERIAL Input / Output Terminal
Control the Display by connecting
to PC.
(see page 25)
2 IR IN,
IR OUT:
Infrared Signal Input / Output
Terminal
Use this when operating more
than one display with one remote
control.
It is possible to receive signal
from the remote control by
connecting the supplied external
IR receiver to the IR IN terminal.
(see page 28)
3 USB:USB Memory Terminal
Connect USB memory to use
[USB media player] function or
to read files. Also, this can be
used to supply power of up to
5V/500mA to an external device
when the picture is displayed.
(see page 29, 98)
4 AV IN
(HDMI):
HDMI Input Terminal
Connect to video equipment such
as VCR or DVD player, etc.
(see page 19)
5 AV IN
(DisplayPort):
DisplayPort Input Terminal
Connect to PC or video
equipment with DisplayPort
output terminal.
(see page 20)
6 DVI-D IN 1,
DVI-D IN 2:
DVI-D Input Terminal
Connect to PC or video
equipment with DVI-D output.
(see page 21)
7 DIGITAL LINK /
LAN IN/OUT:
DIGITAL LINK / LAN Input /
Output Terminal
Connect to a device that sends
video and audio signals via the
DIGITAL LINK terminal.
Alternatively, control the display
by connecting to Network.
Also, when displaying the picture
by daisy chaining multiple
displays, connect to the other
display.
(see page 23, 83)
8 PC IN:PC Input Terminal
Connect to video terminal of PC,
video equipment with “YP
BPR /
YCBCR” or “RGB” output.
(see page 22)
9 AUDIO1 IN:Audio input terminal shared
with DVI-D IN 1 / 2 and PC IN
(see page 21, 22)
English
17
10 COMPONENT /
RGB /
VIDEO IN:
COMPONENT / RGB Video
Input Terminal (R/PR/CR, B/PB/
CB, G/Y)
Connect to video equipment
BPR / YCBCR” or “RGB”
with “YP
output.
(see page 25)
Composite Video Input
Terminal (VIDEO)
Connect to video equipment with
Composite signal output.
(see page 24)
11 AUDIO2 IN:Audio Input Terminal shared
with COMPONENT/RGB IN and
VIDEO IN
(see page 24, 25)
12 AUDIO OUT:Analogue Audio Output
Terminal
Connect to audio equipment with
analogue audio input terminal.
(see page 28)
13 EXT SP:Speaker Terminal
Connect to external speaker.
(see page 29)
Before connecting
●
Before connecting cables, carefully read the operating
instructions for the external device to be connected.
●
Turn off the power of all devices before connecting
cables.
●
Take note of the following points before connecting
the cables. Failure to do so may result in
malfunctions.
When connecting a cable to the unit or a device
•
connected to the unit itself, touch any nearby
metallic objects to eliminate static electricity from
your body before performing work.
Do not use unnecessarily long cables to connect
•
a device to the unit or to the unit body. The
longer the cable, the more susceptible to noise it
becomes. Since using a cable while it is wound
makes it act like an antenna, it is more susceptible
to noise.
When connecting cables, connect GND first, then
•
insert the connecting terminal of the connecting
device in a straight manner.
●
Acquire any connection cable necessary to connect
the external device to the system that is neither
supplied with the device nor available as an option.
●
If the outer shape of the plug of a connection cable
is large, it may come in contact with the plug of an
adjacent connection cable. Use a connection cable
with the suitable plug size for the terminal alignment.
●
If video signals from video equipment contain too
much jitter, the images on the screen may wobble.
In this case, a time base corrector (TBC) must be
connected.
●
When the sync signals output from PC or video
equipment are disturbed, for example, when changing
settings of video output, the colour of the video may
be disturbed temporarily.
●
The unit accepts Composite video signals, YC
BPR signals, analogue RGB signals and digital
YP
signals.
●
Some PC models are not compatible with the unit.
●
Use cable compensator when you connect devices to
the unit using long cables. Otherwise the image may
not display properly.
●
Refer to “Preset Signals” (see page 112 ) for the types
of video signals that can be displayed with the unit.
BCR/
18
English
HDMI terminal connection
Note
●
Video equipment and HDMI cable shown are not
supplied with this unit.
●
Some HDMI equipment may not be able to display
picture.
●
For audio, it is also possible to use AUDIO1 IN or
AUDIO2 IN terminal input. (For [Audio input select]
function, see page 78.)
●
This Display does not support HDMI-CEC (HDMI
Consumer Electronics Control) (VIERA LINK).
HDMI cable (commercially available)
Video Cassette Recorder
DVD Player
PC
Pin assignments and signal names for HDMI
Terminal
Pin No.Signal name
T.M.D.S Data2+
T.M.D.S Data2 Shield
T.M.D.S Data2-
T.M.D.S Data1+
T.M.D.S Data1 Shield
T.M.D.S Data1-
T.M.D.S Data0+
T.M.D.S Data0 Shield
T.M.D.S Data0-
T.M.D.S Clock+
T.M.D.S Clock Shield
T.M.D.S Clock-
SCL
SDA
DDC/CEC Ground
+5V DC
Hot Plug Detect
English
19
DisplayPort terminal connection
Note
●
Additional computer and cables shown are not
supplied with this set.
●
Only Dual Mode (DP++) is compatible with
DisplayPort terminal.
DisplayPort cable (commercially available)
PC with DisplayPort output
Note
●
In connecting with PC which uses early chipsets
or graphic cards compatible with DisplayPort, if the
DisplayPort output of the PC is connected to this unit,
malfunction of this unit or the PC may occur. In that
case, turn the power of the unit or the PC off, and
then turn it on again.
When inputting DisplayPort output to this unit, it
is recommended to use the PC which the newest
Chipset and Graphics Cards are used.
Video equipment, DVI-D cable and audio cable
shown are not supplied with this unit.
●
DVI-D IN terminal is for Single Link only.
●
For audio, it is also possible to use AUDIO2 IN
terminal input. (For [Audio input select] function, see
page 78.)
Shared with PC IN.
DVI-D cable (commercially available)
Stereo mini plug (M3) cable (commercially available)
PC with DVI-D video out
Pin assignments and signal names for DVI-D
Input
Pin No.Signal Name
T.M.D.S. data 2-
T.M.D.S. data 2+
T.M.D.S. data 2 shield
DDC clock
DDC data
T.M.D.S. data 1-
T.M.D.S. data 1+
T.M.D.S. data 1 shield
+5 V DC
GND (Ground)
Hot plug detect
T.M.D.S. data 0-
T.M.D.S. data 0+
T.M.D.S. data 0 shield
T.M.D.S. clock shield
T.M.D.S. clock+
T.M.D.S. clock-
English
21
PC IN terminal connection
Shared with DVI-D IN 1 / DVI-D IN 2.
(Female)
(Male)
Mini D-sub 15p cable (commercially available)
Conversion adapter (if necessary) (commercially
available)
Stereo mini plug (M3) cable (commercially available)
PC
The type of computer signal that can be connected
●
With regard to the typical PC input signals that
are described in “Preset Signals” (see page 112 ),
adjustment values such as for the standard picture
positions and sizes have already been stored in this
unit.
(Computer signals which can be input are those with
a horizontal scanning frequency of 30 to 110 kHz and
vertical scanning frequency of 48 to 120 Hz.)
●
The display resolution is a maximum of 1 440 × 1 080
dots when the aspect mode is set to [4:3], and 1 920
× 1 080 dots when the aspect mode is set to [16:9].
If the display resolution exceeds these maximums, it
may not be possible to show fine detail with sufficient
clarity.
●
In [ENGLISH(US)] OSD language, [16:9] is displayed
as [FULL].
Note
●
Additional computer, cables and conversion adapter
shown are not supplied with this set.
Stereo mini plug
(M3)
Connect a cable
which matches
the audio output
terminal on the
computer.
(commercially
available)
●
Component Input is possible with the pin 1, 2, 3 of the
Mini D-sub 15P Connector.
Change the [Component/RGB-in select] setting in
the [Signal] menu to [Component] (when Component
signal connection) or [RGB] (when RGB signal
connection). (see page 51)
●
The PC IN terminal is DDC2B-compatible. If the
computer being connected is not DDC2B-compatible,
you will need to make setting changes to the
computer at the time of connection.
●
There is no need to use an adapter for computers
with DOS/V compatible Mini D-sub 15P terminal.
●
Do not set the horizontal and vertical scanning
frequencies for PC signals which are above or below
the specified frequency range.
●
For audio, it is also possible to use AUDIO2 IN
terminal input. (For [Audio input select] function, see
page 78.)
Pin assignments and signal names for PC Input
Terminal (Mini D-sub 15P)
45
10
15 14 13 12 11
Pin No.Signal Name
R (PR/CR)
G (Y)
B (PB/CB)
NC (not connected)
GND (Ground)
GND (Ground)
GND (Ground)
GND (Ground)
+5 V DC
GND (Ground)
NC (not connected)
SDA
HD/SYNC
VD
SCL
1
2
67839
22
English
DIGITAL LINK IN / OUT terminal
connection
Twisted pair cable transmitters such as the Panasonic
Digital Interface Box (ET-YFB100G) or the DIGITAL
LINK Switcher (ET-YFB200G) use twisted pair cables
to transmit inputted video and audio signals, and
these digital signals can be input to the Display via the
DIGITAL LINK terminal.
Analogue signal is output as
Digital signal.
Note
●
Video equipment and connection cables are not
supplied with this unit.
●
When connecting with DIGITAL LINK, be sure to
configure each of the [Network settings] settings. (see
page 69)
For the cautions for DIGITAL LINK setting and
connection, see page 84.
●
Corresponding signal for DIGITAL LINK input is the
same as that of HDMI input. (see page 112 )
PC to control the unit
Example: Panasonic ET-YFB100G
PC
Video Cassette Recorder
DVD Player
English
23
Daisy chain connection
COMPONENT/RGB/VIDEOIN
G/Y/VIDEO
B/P
B/CB
R/PR/CR
It is possible to daisy chain multiple displays when
displaying the picture on multi screen, etc.
Note
●
The cable for daisy chain connection is supplied with
this unit. To connect the displays, use the supplied
cable.
●
Up to 10 displays can be connected with a daisy
chain. However, the number of connectable displays
may be limited depending on the cables, signals, the
devices used, etc.
●
When daisy chaining, it may take time for images to
appear on all the displays.
●
HDCP can be supported for up to 8 displays for a
daisy chain.
●
Even if the DIGITAL LINK OUT terminal of this unit
is connected to the DIGITAL LINK input terminal of
another device, audio and video are not output.
VIDEO IN terminal connection
Note
●
Video equipment, connection cables and conversion
plugs are not supplied with this unit.
●
For audio, it is also possible to use AUDIO1 IN
terminal input. (For [Audio input select] function, see
page 78.)
LAN cable (CAT5e) (supplied)
First display
Second display
Third display
24
English
Shared with
COMPONENT/RGB
IN.
Video pin cable (commercially available)
Pin-BNC conversion plug (commercially available)
Stereo audio cable (commercially available)
Video Cassette Recorder
DVD Player
COMPONENT/RGB IN terminal
COMPONENT/RGB/VIDEOIN
G/Y/VIDEO
B/P
B/CB
R/PR/CR
connection
Note
●
Video equipment, cables and conversion adapter
shown are not supplied with this unit.
Shared with VIDEO IN.
SERIAL terminal connection
The SERIAL terminal conforms to the RS-232C interface
specification, so that the Display can be controlled by a
computer which is connected to this terminal.
Note
●
Additional computer and cables shown are not
supplied with this set.
RLPRPBY
Video pin cable (commercially available)
Pin-BNC conversion plug (commercially available)
Stereo audio cable (commercially available)
DVD Player
RGB camera
Note
●
In accordance with the input signal connected to
COMPONENT/RGB IN terminal, select the input
[Component] or [RGB] in [Signal] - [Component/RGBin select]. (see page 51)
●
The RGB signal input to COMPONENT/RGB IN
terminal corresponds to “SYNC ON G” only.
●
For audio, it is also possible to use AUDIO1 IN
terminal input. (For [Audio input select] function, see
page 78.)
(Female)
(Male)
D-sub 9p
RS-232C Straight cable (commercially available)
PC
Note
●
Use the RS-232C straight cable to connect the
computer to the Display.
English
25
It is possible to daisy chain multiple displays, and
then control the specific display with PC.
Pin assignments and signal names for SERIAL
Terminal
13 452
6 789
Pin No.Signal Name
NC (not connected)
RXD
TXD
Non use
GND (Ground)
Non use
RTS
CTS
NC (not connected)
These signal names are those of computer
specifications.
Communication parameters
Signal level: RS-232C compliant
Synchronization method: Asynchronous
Baud rate: 9600 bps
Parity: None
Character length: 8 bits
Stop bit: 1 bit
Flow control: None
Shorted in this set
First display
Second display
Third display
Note
●
When daisy chaining, set [Serial daisy chain position].
(see page 55)
●
When daisy chaining, use a straight cable which pin
to are hard wired.
No.
English
26
Basic format for control data
The transmission of control data from the computer
starts with a STX signal, followed by the command,
the parameters, and lastly an ETX signal in that order.
Add the parameter as required, in accordance with the
control detail.
STX C1 C2 C3P1 P2 P3 P4:P5ETX
Start
(02h)
3-character command
(3 bytes)
Command
CommandParameterControl details
PONNonePower ON
POFNonePower OFF
AVL***Volume 000 - 100
AMT
IMSNoneInput select (toggle)
DAM
Colon
Parameter(s)
0Audio MUTE OFF
1Audio MUTE ON
HM1HDMI input (HDMI)
DP1
DL1
DV1
DV2
PC1PC IN input (PC)
VD1
YP1
UD1USB input (USB)
None
ZOOMZoom1
FULL16:9
NORM4:3
ZOM2Zoom2
DisplayPort input
(DisplayPort)
DIGITAL LINK input
(DIGITAL LINK)
DVI-D IN 1 input
(DVI-D1)
DVI-D IN 2 input
(DVI-D2)
VIDEO input
(VIDEO)
COMPONENT input
(COMPONENT/
RGB IN)
Screen mode select
(toggle)
End
(03h)
Note
●
If multiple commands are transmitted, be sure to
wait for the response for the first command to come
from this unit before sending the next command.
When sending a command which does not require
parameter, a colon (:) is not needed.
●
If an incorrect command is sent by mistake, this
unit will send an “ER401” command back to the
computer.
●
In Standby condition (power OFF with remote control
or <Power button (Unit)>), the unit responds to PON
command only.
●
When [Serial ID function] (see page 54) is set to
[On], only the command that matches the display ID
can be operated.
As the format, add the following header.
AD94;RAD=<XXX>;
For display ID, insert 001 to 100 or 000 for <XXX>.
For group ID, insert AAA (for A) to GGG (for G) for
<XXX>.
●
Consult your local Panasonic dealer for detail
instructions on command usage.
For more details, visit the following web site.
http://panasonic.net/prodisplays/
English
27
IR IN/IR OUT terminal connection
Connect the IR cable (supplied) from the IR OUT
terminal of the first display to the IR IN terminal of the
second display.
The infrared signal of the first display is sent to the
second display.
In this case, the IR (infrared ray reception on the remote
control sensor) on the second display does not operate.
Repeating the above connections enables the daisy
chain connection.
It is possible to receive signal from the remote control
by connecting the supplied external IR receiver to the IR
IN terminal.
Note
●
IR cable is supplied with this unit.
●
While controlling this display, if the external IR
receiver or the IR cable is connected to the IR IN
terminal, the control is performed only with this
terminal.
●
However, [Control settings] - [IR control] can be
selected. (see page 54)
AUDIO OUT terminal connection
Note
●
Audio equipment and the cable shown are not
supplied with this set.
line-in
Stereo audio cable (commercially available)
Audio equipment
Note
●
To output sound from AUDIO OUT terminal of the
unit, be sure to set [Output select] in the [Sound]
menu to [AUDIO OUT]. (see page 43)
External IR Receiver (supplied)
IR cable (supplied)
First display
Second display
Third display
English
28
USB terminal connection
Connect the USB memory to use [USB media player].
(see page 98)
Speaker terminal connection
Please use 8 Ω/10 W speaker.
USB memory device
Pin assignments and signal names for USB Terminal
1342
Pin No.Signal name
+5 V DC
DATA -
DATA +
GND (Ground)
Power of up to 5V/500mA can be supplied to an external
device when the picture is displayed.
●
If the electric current exceeding the power supplying
capability is applied, the output is blocked, and the
following message is displayed.
[USB DC5V OUT overload. Please remove cable or
equipment, then turn the display off/on.]
In this case, remove the equipment and then turn the
power off/on using the remote control, etc.
Note
●
Depending on the type of a USB memory device,
it may come in contact with the periphery such
as a back cover, and cannot be attached. Use a
commercially sold extension cable, or use a small
type of a USB memory device connectable to this
unit.
●
Depending on the USB memory, the access lamp
may remain blinking even when it is not being
accessed. In this case, remove the device after
switching to the input other than USB.
Also, when reading the user image, remove the
device after the menu screen display finishes (see
page 50). When performing the data cloning, remove
the device after the completion screen is displayed.
(see page 105)
Black
Red
While pressing the
lever, insert the core
wire.
Return the lever.
English
29
Identifying Controls
Main Unit
1
2
1 Main power switch ( / )
Switches the main power ON (
●
Turning ON/OFF the <Main power switch> is the
same as plugging or unplugging the power plug.
Switch the <Main power switch> ON (
turn the power ON / OFF with the remote control or
<Power button (Unit)>.
2 Power Indicator / Remote control sensor (Back of
the unit)
The Power Indicator will light.
When the power of the unit is ON (Main power
switch: ON (
●
Picture is displayed: Green
●
Power OFF (Standby) with remote control or
<Power button (Unit)>: Red
•
●
Power OFF with “Power management” function :
Orange
About “Power management” function, see page 66.
When the power of the unit is OFF (Main power
switch: OFF (
Note
●
When the power indicator is orange, power
consumption during standby is generally larger than
that of when the power indicator is red.
))
When [Network control] is set to [On] : Orange
About [Network control] settings, see page 69.
)): No light
) / OFF ( ).
), and then
MENUENTERINPUT
1 External Input Terminal
●
Connects to video equipment, PC, etc. (see
page 17)
2 <Power button (Unit)> (
●
Turns the power ON (Picture is displayed.) / OFF
(standby) when the <Main power switch> (
ON ( ).
3 <INPUT (Unit)>
●
Selects the connected device. (see page 34)
4 <MENU (Unit)>
●
Displays the menu screen. (see page 39)
5 <+ (Unit)> / <- (Unit)>
●
Adjusts the volume. (see page 35)
●
On the main screen, switches settings or adjusts
settings level. (see page 39)
(Unit)> / < (Unit)>
6 <
●
Selects the setting item on menu screen. (see
page 39)
7 <ENTER (Unit)>
●
Configures the item on menu screen. (see
page 39)
●
Switches aspect mode. (see page 37)
-
+
)
/ ) is
30
English
Loading...
+ 91 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.