Panasonic PT-AE500U Owner’s Manual

Panasoni(

LCD Projector /

_ Operating Instructions

Model No. PT-AE500U

Before operating this product, please read the instructionscarefully and save this
manual for future use.

For assistance, please call : 1-888-View-PTV(843-9788)

or send e-mail to : [e-mail]
or visit us at www.panasonic.com (U.S.A)

For assistance, please call : 787-750-4300

or visit us at www.panasonic.co.jp/global/ (Puerto Rico)

TQBJ 0133

Dear Panasonic Customer:

This instruction booklet provides all the necessary operating information that
you might require. We hope it wilt help you to get the most out of your new
product, and that you will be pleased with your Panasonic LCD projector.
The serial number of your product may be found on its back. You should
note it in the space provided below and retain this booklet in case service is
required.

CAUTION: This equipment is equipped with a three-

pin grounding-type power plug. Do not
remove the grounding pin on the power
plug. This plug wilt only fit a grounding-
type power outlet. This is a safety feature.
If you are unable to insert the plug into
the outlet, contact an electrician. Do not
defeat the purpose of the grounding plug.

Do not remove

/

Model number: PT-AE500U
Serial number:

IMPORTANT SAFETY NOTICE

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

PowerSupply:This LCDProjectoris designedto operateon 100V - 240 V,50 Hz/60

HzAC,housecurrentonly.

CAUTION:TheAC powercordwhich issuppliedwith theprojectorasan accessorycan

onlybeused forpowersupplies upto 125V,7 A. Ifyouneedto usehigher
voltagesorcurrentsthanthis,youwillneedto obtainaseparate250V
powercord. Ifyouuse theaccessorycordin suchsituations,firemayresult.

WARNING:

Thisequipmenthasbeentestedandfoundtocomplywiththe limitsfora ClassBdigital
device,pursuantto Part15ofthe FCCRules.Theselimitsaredesignedto provide
reasonableprotectionagainstharmfulinterferenceina residentialinstallation.This
equipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledand
usedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradio
communications.However,thereis noguaranteethatinterferencewillnotoccurina

_articularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioor
televisionreception,whichcanbe determinedbyturningtheequipmentoffandon,theuser
_sencouragedtotryto correctthe interferencebyoneor moreofthe followingmeasures:

- Reorientor relocatethereceivingantenna.

- Increasetheseparationbetweentheequipmentand receiver.

- Connecttheequipmentintoanoutleton acircuitdifferentfromthatto whichthe

receiverisconnected.

- Consultthedealeror anexperiencedradio/TVtechnicianfor help.
FOGCAUTION:To assurecontinuedcompliance,useonlyshieldedinterfacecableswhen

connectingto computersor peripheraldevices.
Anyunauthorizedchangesormodificationstothisequipmentwill voidthe
usersauthoritytooperate.

WARNING:

Not for use in a computer room as defined in the Standard for the Protection
of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the
literature accompanying the product.

2-ENGLISH ENGLISH-3

Model Number: PT-AE500U
Trade Name: Panasonic
Responsible party: Matsushita Electric Corporation of America.

Address: One Panasonic Way Secaucus New Jersey 07094
Telephone number: 1-888-View-PTV(843-9788)
This device complies with Part 15 of the FCC Rules, Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Declaration of Conformity

Contents

Precautions with regard to safety

Preparation

IMPORTANT SAFETY NOTICE ...2
Precautions with regard to

safety ......................................... 5

Accessories ................................. 9

Before use .................................... 9

Location and function of each

part ........................................... 11

Getting started

Setting-up ................................... 16

Projection methods, Projector
position, Projection distances

Connections ............................... 18

Connecting to video equipment,
Connecting to equipment
compatible with YPBPR (CsCR)
signals,
Connecting to computer

Preparation for the remote

control unit .............................. 21

Basic operation

Turning on the power ................ 22

Turning off the power ................ 24

Useful functions

Correcting keystone distortion ...26

Selecting the picture mode .......27

Setting the aspect ratio ............. 28

Turning on the button lights.....30

Pausing a picture ....................... 30

Retrieving the saved picture

settings .................................... 31

Adjustments and settings

On-screen menus ...................... 32

Menu screens, Menu operation
guide, Returning a setting to the
factory default

Adjusting the picture ................. 36

PICTURE MODE, CONTRAST,
BRIGHT, COLOR, TINT,
SHARPNESS, COLOR TEMP.,
AI, ADVANCE MENU,
MEMORY SAVE, MEMORY LOAD,

TV-SYSTEM, SIGNAL MODE,
Projecting sRGB-compatible pictures

Adjusting the position ............... 40

Horizontal position, Vertical position,
DOT CLOCK, CLOCK PHASE,

ASPECT,AUTO SETUP
Turning off the picture

momentarily (SHUTTER) ........ 41

Changing the display language...41

Option settings .......................... 42

OSD, Noise Reduction (NR),
PC PRIORITY, BACK COLOR,

EDID, FRONT/REAR,
DESK/CEILING, FAN CONTROL,
LAMP POWER, LAMP RUNTIME

Care and maintenance

Whenthe TEMP indicator and the

LAMPindicator are illuminated...44
Cleaning and replacing

the air filter .............................. 46

Replacing the lamp unit ............ 47

Before calling for service .......... 50

Cleaning and maintenance .......51

Others

Specifications ............................ 52

Appendix .................................... 54

List of compatible signals,
Connector pin wiring, Projection

dimensions calculation methods

Dimensions ................................ 57

Trademark acknowledgements...58

WARNING

If a problem occurs (such as no image or no sound) or if you notice
smoke or a strange smell coming from the projector, turn off the power
and disconnect the power cord from the wall outlet.

• Do not continue to use the projector in such cases, otherwise fire or

electric shocks could result.

• Check that no more smoke is coming out, and then contact an Authorized
Service Center for repairs.

• Do not attempt to repair the projector yourself, as this can be dangerous.

Do not install this projector in a place which is not strong enough to

take the full weight of the projector.

• Ifthe installation location is not strong enough, it may fall down or tip over,
and severe injury or damage could result.

Installation work (such as ceiling suspension) should only be carried
out by a qualified technician.

• If installation is not carried out correctly, there is the danger that injury or
electric shocks may occur.

If foreign objects or water get inside the projector, or if the projector is
dropped or the cabinet is broken, turn off the power and disconnect the
power cord from the wall outlet.

• Continued use of the projector in this condition may result in fire or electric
shocks.

• Contact an Authorized Service Center for repairs.

Do not overload the wall outlet.

• Ifthe power supply is overloaded (for example, by using too many
adapters), overheating may occur and fire may result.

Do not remove the cover or modify it in any way.

• High voltages which can cause fire or electric shocks are present inside
the projector.

• For any inspection, adjustment and repair work, please contact an
Authorized Service Center.

Clean the power cord plug regularly to prevent it from becoming

covered in dust.

• If dust builds up on the power cord plug, the resulting humidity can
damage the insulation, which could result in fire. Pull the power cord out

from the wall outlet and wipe itwith a dry cloth.

• If not using the projector for an extended period of time, pull the mains
plug out from the wall outlet.

4-ENGL/SH ENGL/SH-5

Do not do anything that might damage the power cord or the power
cord plug.

• Do not damage the power cord, make any modifications to it, place it near
any hot objects, bend itexcessively, twist it, pull it, place heavy objects on

top of it or wrap it into a bundle.

• If the power cord is used while damaged, electric shocks, short-circuits or

fire may result.

• Ask an Authorized Service Center to carry out any repairs to the power
cord that might be necessary.

Do not handle the power cord plug with wet hands.

• Failure to observe this may result in electric shocks.

Insert the power cord plug securely into the wall outlet.

• If the plug is not inserted correctly, electric shocks or overheating could
result.

• Do not use plugs which are damaged or watt outlets which are coming
loose from the watt.

Do not place the projector on top of surfaces which are unstable.

• If the projector is placed on top of a surface which is sloped or unstable, it
may fall down or tip over, and injury or damage could result.

Do not place the projector into water or let it become wet.

• Failure to observe this may result in fire or electric shocks.

Do not place liquid containers on top of the projector.

• If water spills onto the projector or gets inside it, fire or electric shocks
could result.

• If any water gets inside the projector, contact an Authorized Service
Center.

Do not insert any foreign objects into the projector.

• Do not insert any metal objects or flammable objects into the projector or
drop them onto the projector, as doing so can result in fire or electric shocks.

Keep the batteries out of the reach of infants.

• If the batteries are swallowed, death by suffocation may result. If you
believe that the batteries may have been swallowed, seek medical advice
immediately.

Do not allow the + and - terminals of the batteries to come into contact
with metallic objects such as necklaces or hairpins.

• Failure to observe this may cause the batteries to leak, overheat, explode
or catch fire.

• Store the batteries in a plastic bag and keep them away from metallic objects.

During a thunderstorm, do not touch the projector or the cable.

• Electric shocks can result.

Do not use the projector in a bath or shower.

• Fire or electric shocks can result.

6-ENGLISH

Do not look into the lens while the projector is being used.

• Strong light is emitted from the projector's lens. If you look directly into this
light, it can hurt and damage your eyes.

• Be especially careful not to let young children look into the lens. In
addition, turn off the power when you are away from the projector.

Do not place your hands or other objects close to the air outlet port.

• Heated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.

Replacement of the lamp unit should only be carried out by a qualified

technician.

• The lamp unit has high internal pressure. If improperly handled, explosion
might result.

• The lamp unit can easily become damaged if struck against hard objects
or dropped, and injury or malfunctions may result.

When replacing the lamp, allow it to cool for at least one hour before
handling it.

• The lamp cover gets very hot, and contact with it can cause burns.

Before replacing the lamp, be sure to unplug the power cord from the
wall outlet.

• Electric shocks or explosions can result if this is not done.

Caution

Do not cover the air inlet or the air outlet.

• Doing so may cause the projector to overheat, which can cause fire or
damage to the projector.

• Do not place the projector in narrow, badly ventilated places such as
closets or bookshelves.

Do not set up the projector in humid or dusty places or in places where

the projector may come into contact with smoke or steam.

• Using the projectorunder such conditions may result infire or electric shocks.

When disconnecting the power cord, hold the plug, not the cord.

• If the power cord itself is pulled, the cord will become damaged, and fire,
short-circuits or serious electric shocks may result.

Always disconnect all cables before moving the projector.

• Moving the projector with cables still attached can damage the cables,
which could cause fire or electric shocks to occur.

Do not place any heavy objects on top of the projector.

• Failure to observe this may cause the projector to become unbalanced
and fall, which could result in damage or injury.

Do not short-circuit, heat or disassemble the batteries or place them
into water or fire.

• Failure to observe this may cause the batteries to overheat, leak, explode
or catch fire, and burns or other injury may result.

ENGLISH-7

When inserting the batteries, make sure the polarities (+ and -) are
correct.

• If the batteries are inserted incorrectly, they may explode or leak, and fire,

injury or contamination of the battery compartment and surrounding area
may result.

Use only the specified batteries.

• If incorrect batteries are used, they may explode or leak, and fire, injury or
contamination of the battery compartment and surrounding area may

result.

Do not mix old and new batteries.

• If the batteries are inserted incorrectly, they may explode or leak, and fire,
injury or contamination of the battery compartment and surrounding area
may result.

Do not put your weight on this projector.

• You could fall or the projector could break, and injury may result.

• Be especially careful not to let young children climb onto the projector.

Disconnect the power cord plug from the wall outlet as a safety
precaution before carrying out any cleaning.

• Electric shocks can result if this is not done.

Ask an Authorized Service Center to clean inside the projector at least

once a year.

• If dust is leftto build up inside the projector without being cleaned out, it
can result in fire or problems with operation.

• It is a good idea to clean the inside of the projector before the season for
humid weather arrives. Ask your nearest Authorized Service Center to

clean the projector when required. Please discuss with the Authorized
Service Center regarding cleaning costs.

We are constantly making efforts to preserve and maintain a clean
environment. Please take non repairable units back to your dealer or a
recycling company.

Accessories

Check that all of the accessories shown below have been included with your
projector.

Remote control unit

N2QAEA000019 xl )

Video cable
[3.0 m (9"10"),

K2KA2FA00003 xl ]

Power cord
(K2CG3FR00001 x 1)

AAA batteries for
remote control unit (x2)

Carrying bag
(TPEP008 xl )

-1

Before use

Cautions when moving the projector

Be sure to attach the lens cover before moving the projector.

The projection lens is extremely susceptible to vibration and shocks. When

moving the projector, use the accessory carrying bag. When placing the
projector inside the carrying bag, position it so that the lens is facing upward.

NOTICE:

• This product has a High Intensity Discharge (HID) lamp that contains a
small amount of mercury. It also contains lead in some components.
Disposal of these materials may be regulated in your community due to
environmental considerations. For disposal or recycling information
please contact your local authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>

8-ENGL/SH

Cautions regarding setting-up

Avoid setting up in places which are subject to vibration or shocks.

The internal parts can be damaged, which may cause malfunctions or

accidents.

Do not set up the projector near high-voltage power lines or near
motors.

The projector may be subject to electromagnetic interference.

If installing the projector to the ceiling, ask a qualified technician to
carry out all installation work.

You will need to purchase the separate installation kit (Model No.ET-PKE300).

Furthermore, all installation work should only be carried out by a qualified
technician.

ENGLISH-9

If using this projector at high elevations (above 1 400 m),
set the "FAN CONTROL" to "HIGH". (Refer to page 43.)

Failure to observe this may result in malfunctions.

Notes on use

In order to get the best picture quality

Draw curtains or blinds over any windows and turn off any fluorescent lights
near the screen to prevent outside light or light from indoor lamps from
shining onto the screen.

Do not touch the surfaces of the lens with your bare hands.

Ifthe surface of the lens becomes dirty from fingerprints or anything else, this

will be magnified and projected onto the screen. Moreover, when not using
the projector, retract the lens and then cover it with the accessory lens cover.

Screen

Do not apply any volatile substances which may cause discoloration to the
screen, and do not let it become dirty or damaged.

Lamp

The lamp may need to be replaced earlier due to variables such as individual
lamp characteristics, usage conditions and the installation environment,

especially when the projector is subjected to continuous use for more than

10 hours or the power is frequently turned on and off.

Liquid crystal panel

• Do not project the same image for long periods of time, as this may remain

as an afterimage on the liquid crystal panel.

• The liquid crystal panel of the projector is built with very high precision
technology to provide fine picture details. Occasionally, a few non-active

pixets may appear on the screen as fixed points of blue, green or red.
Please note that this does not affect the performance of your LCD.

Location and function of each part

Projector <Top, right and front>

®
®

Projector control panel (page 14)

_Zoom ring (page 23)

Focus ring (page 23)
Projection lens

_Air inlet ports

Do not cover these ports.

® Front adjustable legs(L/R) (page 23)

Lens cover

® Leg adjuster buttons(L/R) (page 23)

These buttons are used to unlock the front adjustable legs. Press to adjust
the angle of tilt of the projector.

_Air filter (page 46)
_ Remote control signal receptor (page 21)
_MAIN POWER switch (pages 22 and 24)

IO-ENGLISH ENGL_H-11

Projector <Back and bottom> Connector panel

,. .a

YC

: ! PB_CB

:_ PR_R

(_Air outlet port

Do not cover this port.
Connector panel (page 13)

(_ Power input socket (AC IN) (page 22)

The accessory power cord is connected here. Do not use any power cord

other than the accessory power cord.

(_ Lamp unit holder (page 47)
(_ Security lock

This can be used to connect a commercially-available theft-prevention

cable (manufactured by Kensington). This security lock is compatible with

the Microsaver Security System from Kensington.

WARNING

Do not place your hands or other objects close to the air outlet port.

• Heated air comes out of the air outlet port. Do not place your hands or

face, or objects which cannot withstand heat close to this port, otherwise

burns or damage could result.

(_TRIGGER output jack (pages 18, 19 and 20)

This jack outputs 12 V when the power is turned on. Connect this jack to
equipment such as an electric screen.

(_ S-VIDEO input connector (page 18)

This connector is used to input signals from an S-VIDEO-compatible
equipment such as a video deck.

(_ DVI-D IN connector (page 20)

This connector is used to input DVI-D signals.

(_ RGB input connector (page 20)

This connector is used to input RGB signals from a PC.

(_ YPBPR(CBCR) input jacks(page 19)

These jacks are used to input YPBPR signals from compatible equipment
such as a DVD player.

®VIDEO input jack (page 18)

This jack is used to input video signals from a video equipment such as a
video deck.

12-ENGLISH ENGLISH-13

Projector control panel

®
®

®

o%o

Remote control unit

MENU EN_:R

LCDPROJECI_OR

®
®

_TEMP indicator (page 44)

This indicator illuminates ifan abnormally high temperature is detected
inside the projector. If the temperature rises above a certain level, the
power supply will be turned off automatically and the indicator will flash.

(_ LAMP indicator (page 45)

This indicator illuminates when it is time to replace the lamp unit. It flashes
if a circuit abnormality is detected.

(_ Power indicator (pages 22, 24 and 25)

This indicator illuminates red when the main power is switched on (standby
mode), and it illuminates green when projection of an image begins.

(_ POWER button (pages 22 and 24)
(_MENU button (page 32)

This button is used to display the "MAIN MENU". When a menu screen is
being displayed, it can be used to return to a previous screen or to clear the

screen.

®Arrow (&, V, • and II_) buttons (page 34)

These buttons are used to select and adjust items in the on-screen menus.

(_ ENTER button (page 34)

This button is used to accept and to activate items selected in the
on-screen menus.

(_INPUT select button (page 23)

These buttons are used to switch the input signals from the connected
equipment.

(_ KEYSTONE button (page 26)

This button is used to correct keystone distortion of the projected image
when the projector position is tilted upward or downward.

(_NORMAL button (page 35)

This button is used to reset the projector adjustment values to the factory
default settings.

@ASPECT button (page 28)

This button is used for aspect adjustment (vertical and horizontal
proportions).

@ LIGHT button (page 30)

This button is used to illuminate the buttons on the remote control unit.

@ FREEZE button (page 30)

This button is used to momentarily freeze projection so that a still picture is
displayed.

1(_PICTURE MODE button (page 27)

This button is used to display the "PICTURE MODE" menu.

(_ USER MEMORY button (page 31)

This button is used to display the "MEMORY LOAD" menu.

14-ENGLISH ENGLISH-15

Setting-up

Projection methods

In way of installing projector, any one of the following four projection methods
are used. Select whichever projection method matches the setting-up
method. (The projection method can be set from the "OPTION" menu. Refer
to page 43 for details.)

• Front-desk projection

FRONT/REAR FRONT

DESK/CEILING DESK

• Rear-desk projection
(Using a translucent screen)

• Front-ceiling projection

FRONT/REAR FRONT

DESK/CEILING CEILING

• Rear-ceiling projection
(Using a translucent screen)

Projector position

-r _Top edge of screen
o_ Screen -_"----.

Bottom edge of screen _

_\\\\\\\\\\\\\\\\\\_

Projection distances

<Units: mm (inch)>

L: Projection distance
SH: Image height
SW: Image width

HI: Distance from center

of lens to bottom edge
of projected image

Te_

1.01 m(40") 0.50 m(1 "T`) 0,89 m(2"11"`) 1.2 m(3"11") 1.4 m(4"7") 0.03m(1-5/32")

1.27 m(50") 0.62 m(2") 1,11 m(3"7") 1.6 m(5"2"`) 1.8 m(5"10") 0.04 m(1-9/16")

1.52 m(60") 0.75 m(2"5"`) 1,33 m(4"4") 1.9 m(6"2"`) 2.2 m(T2") 0.04 m(1-9/16")

FRONT/REAR REAR

DESK/CEILING DESK

FRONT/REAR REAR

DESK/CEILING CEILING

1.77 m(70") 0.87 m(2"10') 1,55 m(5"1") 2.2 re(T2') 2.5 m(8"2") 0.05m(1-15/16'_

2,03 m(80") 1.00 m(3"3"`) 1,77 m(5"9") 2.5 m(8"2"`) 2.9 m(9"6") 0.06m(2-11/32"_
2,28 m(90") 1.12 m(3"8"`) 1,99 m(6"6') 2.6 m(9"2"`) 3.3 m(10"9") 0.06m(2-11/32'_

2,54m(100") 1,24m(4") 2,21 m(7"3") 3.1 m(10"2') 3.7m(12"1") 0.07m(2-3/4")

3,81 m(150") 1.87m(6"1"`) 3,32m(10"10") 4.7m(15"5') 5.6m(18"4") 0.10m(3-29/32"_

5.08 m(200") 2.49 m(8"2"`) 4,43 m(14"6"`) 6.2 m(20"4') 7.4 m(24"3") 0.14 m(5-1/2")

16-ENGLISH ENGLISH-17