Panasonic Pcf1, Pcv1 Operating Instructions
Manufactured by:
81-IN3046-9922
Before attempting to connect or operate this product, please read these instructions completely.
for
MODEL: Miniature Camera
PCF1, PCV1
DESCRIPTION: Outdoor Pedestal Mount Housing,
Color Camera
STANDARD INSTALLATION PROCEDURE
INCLUDES MODELS: PCF1, PCV1
CONTENTS INCLUDE:
(1) Housing
(1) Weather hood
(1) Cover plate
(1) Cover plate gasket
(1) Allen wrench security head tool
(2) Stainless steel 6-32x1/2" captive Security head screws
(1) Camera mount bracket
(1) Camera bracket arm
(1) Bottom mount bracket with PC Board
(1) Top mount bracket with camera and lens
(2) 4-40 x 1/4" screws
(2) Star washers
(4) 2-56 x 3/16" screws
1. Remove the cover plate by loosening the 2 security head
screws with the security tool.
2. If mounting the unit to a wall:
A. Remove the 2 Phillips head screws that secure the
bottom mount bracket and PC Board to the housing,
then remove the bracket. Repeat for the top mount
bracket and camera.
B. Place the housing face down on a flat surface and use
a hammer to remove the knockout located at the
center of the back of the housing.
C. Use the 2 mounting holes and the appropriate
hardware (not included)to secure the housing to the
wall.
PRODUCT INSTRUCTIONS
3. If mounting the unit on a pedestal:
NOTE: 3/4" conduit with a threaded end is required for this
method of installation.
A. Install the conduit in the desired location; run the
wiring through the conduit.
B. Place the PFC1/PCV1 housing onto the conduit, feed
the wires through the bottom hole and thread the
housing onto the conduit until tight.
N NOTE: Apply silicone sealant to the conduit threads and
the hole plug to ensure a water tight seal.
4. Make the necessary connections to the PC Board and
reattach the bottom bracket to the housing.
USE CLASS 2 POWER ONLY
!
5. Hand place the top bracket and camera into the unit.
Check the angle of the camera, remove the bracket/
camera and make any necessary adjustments. Once
you have achieved the desired camera angle, reattach
the top bracket and camera to the housing.
6. Fine focusing (see diagram below):
Fixed Lens: Manually rotate the lens until a clear picture is
achieved.
Vari-Focal Lens: First, adjust the Magnification Lock Screw
to the desired magnification (telephoto
to wide angle). Tighten the Lock Screw.
Next, adjust the Focus Lock Screw until a
clear picture is achieved. Tighten the
Lock Screw.
Camera Fine Focus
Fixed Lens Camera
(PCF1)
Manual focus
Top mount bracket and camera
Bottom mount bracket and PC Board
Vari-focal Lens Camera
(PCV1)
Focus Lock Screw
Magnification
Lock Screw
6. Replace the cover on the housing and reattach using the
2 security screws.
Specification
Lens Type
Model Number
Scanning Area
Scanning
Horizontal
Vertical
Synchronization
Video Output
Horizontal Resolution
Signal-to-Noise Ratio
Minimum Illumination
Angular Field of View
Horizontal
Vertical
AGC
ELC
White Balance
Ambient Operating
Temperature
Ambient Operating
Humidity
Power Source
at AC Source
at DC Source
Dimensions
Weight
Connections
2.82"
W
4.6"
H
2.82"
D
0.68
kg
1.5
lbs
Video
BNC Connectors
3 - 8mm Fixed Focal Lens Series 4 - 8mm Vari- -Focal Lens Series
PCF1
PCF3PCF2
PCF4
PCF5
361 mm (H) x 272 mm (V) (Equivalent to scanning area of 1/4" pick-up tube)
525 lines / 60 fields / 30 frames
Internal Synchronization
1.0 V (p-p) NTSC Composite 75 ohms / BNC Connector
330 lines (at center area)
46 dB (with AGC OFF)
0.5 Footcandle (5 Lux) at F2.0 0.5 Footcandle (5 Lux) at F2.0 - 1.0 Footcandle
Horizontal 53.4˚
Vertical 40.0˚ Vertical 38.4 - 20.0˚
3.15"
5.25"
6.0"
6.0"
6.0"
0.45
1
4.9"
3.2"
0.45
1
3.0"
3.625"
0.45
1
15.9"
11.2"
15.9"
1.8
4
Dimensions for the PCF1/PCV1 (not to scale)
PCF6W
PCF6
15.734 kHz
59.94 kHz
(10 Lux) at F2.8
On (Preset)
On (Preset)
ATW (Preset)
-10˚C - +50˚C (14˚F - 122˚F)
Less than 90%
24 VAC, 40 ma
12 VDC, 80 ma
6.0"
6.0"
6.0"
0.68
1.5
6.0"
10.8"
7.0"
0.91
2
2.82"
4.6"
2.82"
0.68
1.5
CAUTION: To prevent fire or shock hazard, the UL-Listed
wire VW-1, style 1007, should be used for the
cable for 24 VAC input terminals.
PCV2PCV1
PCV3
Horizontal 51.7 - 26.7˚
6.0"
3.15"
6.0"
4.9"
6.0"
3.2"
0.45
0.45
1
1
PCV4
5.25"
3.0"
3.625"
0.45
1
PCV5
15.9"
11.2"
15.9"
1.8
4
PCV6
6.0"
6.0"
6.0"
0.68
1.5
PCV6W
6.0"
10.8"
7.0"
0.91
2
Power Connections
NOTE: Splice wiring according to
standard electrical guidlines.
Positive and Negative connections are
interchangeable with this PC Board.
Wiring Chart-Cable Distance
This Chart is based on a 12VDC power supply with the
maximum Amp draw at .500 amps.
WIRE 20 18 16
FT. 180' 300' 480'
- 2 -
Loading...