Panasonic kx-tga200 Operation Manual

– 1 –

Operating Instructions

PLEASE READ BEFORE USE AND
SAVE.

KX-TGA200B is the optional cordless
handset for the KX-TG2000B. These
operating instructions cover most of the
features of this cordless handset.
Please read the KX-TG2000B operating
instructions for further details.

2.4GHz Cordless Handset

Model No. KX-TGA200B

Accessories (included)

For extra orders,
call 1-800-332-5368

Charger .................one

AC Adaptor............one

Order No. KX-TCA1-G

Belt Clip.................one

Order No. PQKE10101Z1

Power Outlet
(AC 120 V, 60 Hz)

AC Adaptor

Fasten the AC adaptor
cord to prevent it from
being disconnected.

Bottom
of the
charger

• USE ONLY WITH Panasonic AC ADAPTOR KX-TCA1 (Order No. KX-TCA1-G).

• The AC adaptor must remain connected at all times. (It is normal for the adaptor to

feel warm during use.)

Printed in Japan

PQQX12632ZA SS0300NA0

Installation ................................... 1

Location of Controls..................... 2

Registering Cordless Handsets ... 3

Making Calls ................................ 3

Answering Calls........................... 4

Intercom....................................... 4

Transferring a Call ....................... 4

Storing Names and Numbers

in the Directory ......................... 5

Dialing from the Directory ............ 6

Erasing an Item in the Directory .. 6

Caller ID Service.......................... 6

Viewing the Caller List ................. 7

Calling Back from the Caller List

.. 7

Voice Mail System ....................... 7

Automated Attendant System...... 8

Listening to Messages................. 9

Delivering Your Own Message ....10

Remote Operation from a Touch

Tone Phone ..............................10

Wall Mounting..............................11

Using an Optional Headset..........11

Canceling Handset Registration ..11

Using the Belt Clip .......................12

Battery Replacement ...................12

Installation

Connecting the AC adaptor to the charger

Contents

(ENTER)

/

(Voice Mail)

(CLEAR)

Navigator Key
( , , I, H)

Display

(REDIAL/EDIT)

Charge Contacts

(TALK)

(FUNCTION/EXIT)

(INTERCOM/HOLD/TRANSFER)

(LINE!2)

(LINE!1)

Headset Jack

CHARGE
Indicator

Charge Contacts

• Clean the charge contacts of the handset and the charger with a soft, dry

cloth once a month. Clean more often if the unit is subject to grease, dust or
high humidity. Otherwise the battery may not charge properly.

Handset battery information

After your Panasonic battery is fully charged:

Approx. battery lifeOperation

While in use (TALK) Up to about 8 hours

While not in use (Standby)

CHARGE Indicator

Charging the battery

Place the cordless handset on the charger and
charge for about 8 hours before initial use.
Make sure the handset faces forward as shown.

• The CHARGE indicator lights.

• Recharge the battery when:

– “

Recharge” is displayed,

– “ ” flashes on the display, or
– the handset beeps intermittently while it

is in use.

Location of Controls

Up to about 4 days

– 2 –

Registering Cordless Handsets

1

Base unit:

Press (FUNCTION).

2

Select “Registration” by
pressing or , and press H.

3

Select “HS registration” by
pressing or , and press H.

4

Cordless handset:

Press (FUNCTION).

5

Select “Registration” by
pressing or , and press H.

6

Select “HS registration” by
pressing or , and press H.

Registration is necessary for cordless handsets. A handset will be assigned
the number at registration. The handset number is used as the extension
number (p. 4, 8). You can register up to 8 cordless handsets at the
KX-TG2000B base unit.
This unit can handle up to 2 external telephone lines or up to 2 internal lines.
Operating more than one cordless handset allows you to have:

– two external calls simultaneously,
– two internal calls simultaneously, or
–

one internal call while simultaneously conducting two external calls.

Make sure that the base unit and cordless handset are in the standby mode.
Registration must be completed within 1 minute.

Base unit/Cordless handset:

7

The base unit and handset
displays show the assigned
handset number. Press (EXIT).

• The handset number ([1]–[8]) will be

displayed in the standby mode.

If a PIN (Personal Identification
Number) has been stored:

Follow steps 1 to 6, and enter the
PIN. Press (ENTER).

Making Calls

Two calls can be handled simultaneously on separate telephone lines by the
base unit and a cordless handset (or by 2 cordless handsets).

Press (TALK).

1

• You can press a line button instead of pressing (TALK).

Dial a phone number.

2

To hang up, press (TALK) or place the handset on the charger.

3

• To adjust the handset volume (3 levels), press or while talking.

To dial after confirming the entered number:

Enter a phone number, and press (TALK).

• To redial a number from the redial list (contains the last 10 numbers dialed), press

(REDIAL) until the desired number is displayed, and press (TALK).

– 3 –

– 4 –

Intercom

Each number assigned to a handset at registration is the extension number
(p. 3). The base unit extension number is 0.

Making intercom calls

1

Press (INTERCOM).

2

To page the base unit, enter (0)

.

To page another handset, enter the extension number (

(1) to (8)).

3

To end the intercom, press (TALK) or place the handset on the charger.

• To answer an intercom call, press (TALK) or lift the handset off the charger.

Transferring a Call

1

During a call, press (TRANSFER).

2

To page the base unit, enter (0).
To page another handset, enter the extension number ((1) to (8)).

3

If required, wait for the paged party to answer, and you can announce
the transfer.
If not required, go to step 4.

4

To complete the transfer, press (TALK) or place the handset on the
charger.

Answering Calls

Two calls can be handled simultaneously by the base unit and a cordless
handset (or by 2 cordless handsets).

Press (TALK).

• You can press the called line button

instead of pressing

(TALK).

• You can also answer a call by pressing

any dialing button (0) to (9),

(*)

or (#).

OR
If the handset is on the charger, just

lift up.

What “ ” on the display mean:

Off (invisible): The line is free.
On: The line is being used.
Flashing:

A call is on hold. The Automated
Attendant System or Answering
System is responding to a call.

Flashing quickly

:

A call is being received.

,

• During a conversation, if two tones sound, an incoming call is being received on the

other line. To answer the second call while holding the first call, press

(HOLD) and

press the other line button. To return to the first call, press the line button.