Panasonic kx-hns102 Operation Manual
Installation Guide
Home Network System
Motion Sensor
Model No. KX-HNS102
Thank you for purchasing a Panasonic product.
This document explains how to install the motion sensor properly.
For details about how to use the system, refer to the User’s Guide
(page 14).
Please read this document before using the unit and save it for future
reference.
For assistance, visit our Web site: www.panasonic.com/support
for customers in the U.S.A. or Puerto Rico.
Please register your product: www.panasonic.com/prodreg
Printed in China
Table of Contents
Introduction
Accessory information ...............3
Important Information
About this system ......................4
For your safety ...........................4
Important safety instructions ......5
For best performance ................5
Other information .......................6
Setup
Part names and functions ..........7
About the LED indicator .............7
Setup overview ..........................7
Inserting the batteries ................8
Registering the motion
sensor ........................................8
Information about sensor
features ......................................9
Confirming the usage area ......11
Wall mounting ..........................12
Appendix
Testing the motion sensor .......14
Adjusting the sensor
sensitivity .................................14
Features available when using the
[Home Network] app ................14
Accessing the User’s Guide ....14
Specifications ..........................15
FCC and other information ......16
Customer services ...................18
Warranty (For United States and
Puerto Rico) .............................19
2
Introduction
Accessory information
Supplied accessories
No. Accessory item/Part number Quantity
A
B
C Wall mounting screws (25 mm (1 inch))/XTB4+25AVW 2
*1 When replacing batteries, see “Power source” of “Specifications”, page 15
for battery information.
*2 The motion sensor can be wall mounted with or without the wall mounting
adaptor (page 12).
A B C
Other information
R Design and specifications are subject to change without notice.
R The illustrations in these instructions may vary slightly from the actual product.
Trademarks
R iPhone and iPad are registered trademarks of Apple Inc.
R Android™ is a trademark of Google Inc.
*1
Batteries
Wall mounting adaptor*2/PNKK1111Z1
2
1
For assistance, please visit www.panasonic.com/support
3
Important Information
About this system
This system is an auxiliary system; it is
not designed to provide complete
protection from property loss.
Panasonic will not be held responsible
in the event that property loss occurs
while this system is in operation.
For your safety
To prevent severe injury and loss of life/
property, read this section carefully
before using the product to ensure
proper and safe operation of your
product.
WARNING
Power connection
R Use only the power source marked
on the product.
R Do not connect non-specified
devices.
Installation
R To prevent the risk of fire or
electrical shock, do not expose the
product to rain or any type of
moisture.
R Do not place or use this product
near automatically controlled
devices such as automatic doors
and fire alarms. Radio waves
emitted from this product may cause
such devices to malfunction
resulting in an accident.
R Keep small parts (screws, etc.) out
of the reach of children. There is a
risk of swallowing. In the event they
are swallowed, seek medical advice
immediately.
Operating safeguards
R Do not disassemble the product.
Medical
R Consult the manufacturer of any
personal medical devices, such as
pacemakers or hearing aids, to
determine if they are adequately
shielded from external RF (radio
frequency) energy. DECT features
operate between 1.92 GHz and
1.93 GHz with a peak transmission
power of 115 mW.
R Do not use the product in health
care facilities if any regulations
posted in the area instruct you not to
do so. Hospitals or health care
facilities may be using equipment
that could be sensitive to external
RF energy.
CAUTION
Battery
R The batteries should be used
correctly, otherwise the product may
be damaged due to battery leakage.
R Do not charge, short-circuit,
disassemble, or heat the batteries.
R Do not dispose of batteries in a fire.
R Remove all the batteries when
replacing.
R Do not mix old, new or different
types of batteries.
R It is recommended that batteries are
replaced annually.
R It is recommended that batteries are
replaced after a power outage.
R Keep out of the reach of small
children. There is a risk of
For assistance, please visit www.panasonic.com/support
4
Important Information
swallowing. If the battery is
swallowed, seek medical attention
immediately.
R Remove the battery if it becomes
unusable. There is a risk of leakage,
overheating, and rupture. Do not
attempt to use a battery if it is
leaking.
R Do not intentionally pour water on
the battery or allow it to get wet.
There is a risk of fire and smoke. If
the battery becomes wet, remove it
immediately and contact an
authorized service center.
Important safety instructions
When using your product, basic safety
precautions should always be followed
to reduce the risk of fire, electric shock,
and injury to persons, including the
following:
1. Do not use this product near water
for example, near a bathtub,
washbowl, kitchen sink, or laundry
tub, in a wet basement or near a
swimming pool.
2. Use only the batteries indicated in
this document. Do not dispose of
batteries in a fire. They may
explode. Check with local codes for
possible special disposal
instructions.
SAVE THESE INSTRUCTIONS
For assistance, please visit www.panasonic.com/support
For best performance
Hub location/avoiding noise
The hub and other compatible
Panasonic devices use radio waves to
communicate with each other.
R For maximum coverage and
noise-free communications, place
your hub:
– at a convenient, high, and central
location with no obstructions
between the product and hub in
an indoor environment.
– away from electronic appliances
such as TVs, radios, personal
computers, wireless devices, or
other phones.
– facing away from radio frequency
transmitters, such as external
antennas of mobile phone cell
stations. (Avoid putting the hub
on a bay window or near a
window.)
R If the reception for a hub location is
not satisfactory, move the hub to
another location for better reception.
Environment
R Keep the product away from
electrical noise generating devices,
such as fluorescent lamps and
motors.
R The product should be kept free
from excessive smoke, dust, high
temperature, and vibration.
R The product should not be exposed
to direct sunlight.
R Do not place heavy objects on top of
the product.
R The product should be kept away
from heat sources such as heaters,
kitchen stoves, etc. It should not be
placed in rooms where the
5
1
2
3
Important Information
temperature is less than 0 °C (32 °F)
or greater than 40 °C (104 °F).
Damp basements should also be
avoided.
R Operating the product near electrical
appliances may cause interference.
Move away from the electrical
appliances.
Other information
CAUTION: Risk of explosion if battery
is replaced by an incorrect type.
Dispose of used batteries according to
the instructions.
Routine care
R Wipe the outer surface of the
product with a soft moist cloth.
R Do not use benzine, thinner, or any
abrasive powder.
Information on Disposal in other
Countries outside the European
Union
Notice
These symbols (A, B, C) are only
valid in the European Union. If you
wish to discard these items, please
contact your local authorities or dealer
and ask for the correct method of
disposal.
For assistance, please visit www.panasonic.com/support
6
A
B
C
D
E
Indicator Status
Part names and functions
Red, lit Motion was detected
Red,
blinking
Green,
blinking
Off No battery power
Note:
R The LED indicator does not indicate
sensor status if the sensor has not
been registered (page 8).
Setup overview
1 Initial setup
Make sure you can access the
system using your mobile device.
For details, refer to the System
Infrared sensor
LED indicator
MHIGHN/MLOWN
Used to change the sensor
sensitivity (page 14).
Rear cover
M N
Used to confirm the status of the
sensor or register the sensor to
the hub.
About the LED indicator
You can press M
LED indicator to confirm the sensor’s
status.
Indicator Status
Green, lit No motion detected
For assistance, please visit www.panasonic.com/support
N and check the
Setup Guide included with your
hub.
2 Insert the batteries
The motion sensor is battery
powered.
3 Registration
Required only if the motion sensor
was purchased separately (i.e.,
not as part of a bundle).
4 Confirm the installation area
Read the information in this
document to confirm that the
desired installation area is suitable
to proper operation.
5 Installation
Install the motion sensor in the
desired location.
Setup
Sensor is out of range
of the hub
Registration mode
(You pressed and held
M N)
7
Loading...