Panasonic KX-FT982LS-B, KX-FT984LS-B, KX-FT988LS-B Service Manual

ORDER NO. KMF0806164CE

Personal Facsimile / Facsimile with Digital Answering System

Model No. KX-FT982LS-B

KX-FT984LS-B KX-FT988LS-B

Black version (for Latin America)

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

TABLE OF CONTENTS

PAG E PAG E

1 Safety Precautions ----------------------------------------------- 4

1.1. For Service Technicians --------------------------------- 4

1.2. AC Caution -------------------------------------------------- 4

1.3. Personal Safety Precautions --------------------------- 5

1.4. Service Precautions--------------------------------------- 6

2 Warning-------------------------------------------------------------- 7

2.1. About Lead Free Solder (PbF: Pb free)-------------- 7

2.2. Insulation Resistance Test ------------------------------ 8

2.3. Battery Caution--------------------------------------------- 8

2.4. Discarding of P. C. Board -------------------------------- 8

3 Specifications ----------------------------------------------------- 9 4 General/Introduction -------------------------------------------10

4.1. Optional Accessories ------------------------------------10

4.2. Translation Lists-------------------------------------------10

5Features------------------------------------------------------------ 11 6 Technical Descriptions ----------------------------------------12

6.1. Connection Diagram -------------------------------------12

6.2. General Block ---------------------------------------------13

6.3. Control Section--------------------------------------------15

6.4. Facsimile Section-----------------------------------------21

6.5. Sensors and Switches-----------------------------------27

6.6. Modem Section -------------------------------------------31

6.7. NCU Section -----------------------------------------------38

6.8. ITS (Integrated Telephone System) and Monitor Section -------------------------------------------42

6.9. TAM Interface Section (KX-FT982/KX-FT984 only)----------------------------------------------------------42

6.10. ATAS (Automatic Telephone Answering System) Section (KX-FT988 only)--------------------43

6.11. Operation Board Section -------------------------------44

6.12. LCD Section -----------------------------------------------45

6.13. Power Supply Board Section --------------------------46

7 Location of Controls and Components ------------------49

7.1. Overview----------------------------------------------------49

7.2. Control Panel ----------------------------------------------49

8 Installation Instructions ---------------------------------------50

8.1. Installation Space-----------------------------------------50

8.2. Connections------------------------------------------------51

8.3. Installing the Recording Paper ------------------------51

8.4. Documents the Unit can Send ------------------------52

9 Operating Instructions-----------------------------------------53

9.1. Setting Logo -----------------------------------------------53

10 Test Mode ----------------------------------------------------------55

10.1. DTMF Single Tone Transmit Selection --------------56

10.2. Button Code Table----------------------------------------57

10.3. Print Test Pattern -----------------------------------------58

11 Se rvice Mode -----------------------------------------------------59

11.1. Programing and Lists ------------------------------------59

11.2. The Example of the Printed List ----------------------63

12 Troubleshooting Guide ----------------------------------------68

12.1. Troubleshooting Summary -----------------------------68

12.2. Error Messages-Display --------------------------------69

12.3. Error Messages-Report ---------------------------------71

12.4. Remote Programming -----------------------------------93

12.5. Troubleshooting Details---------------------------------96

13 Service Fixture & Tools--------------------------------------128 14 Disassembly and Assembly Instructions -------------129

14.1. Upper Cabinet Section -------------------------------- 130

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

14.2. Lower Cabinet Section-------------------------------- 133

14.3. Operation Panel Section ---------------------------- 136

14.4. Installation Position of the Lead Wires------------ 139

15 Maintenance ---------------------------------------------------- 141

15.1. Maintenance Items and Component Locations- 141

15.2. Gear Section -------------------------------------------- 143

15.3. Jams------------------------------------------------------- 149

15.4. Cleaning -------------------------------------------------- 150

16 Miscellaneous -------------------------------------------------- 152

16.1. Terminal Guide of ICs Transistors and Diodes - 152

16.2. How to Replace the Flat Package IC ------------- 154

16.3. Test Chart ------------------------------------------------ 155

17 Schematic Diagram ------------------------------------------ 158

17.1. Digital Board (PCB1): KX-FT982/KX-FT984 ---- 158

17.2. Digital Board (PCB1): KX-FT988------------------- 162

17.3. Analog Board (PCB2) --------------------------------- 166

17.4. Operation Board (PCB3/PCB203) ----------------- 168

17.5. Power Supply Board (PCB4)------------------------ 169

18 Printed Circuit Board ---------------------------------------- 171

18.1. Digital Board (PCB1) ---------------------------------- 171

18.2. Analog Board (PCB2) -------------------------------- 173

18.3. Operation Board (PCB3/PCB203) ----------------- 175

18.4. Power Supply Board (PCB4)------------------------ 177

19 Appendix Information of Schematic Diagram------- 178 20 Exploded View and Replacement Parts List --------- 179

20.1. Cabinet and Mechanical Parts Location---------- 179

20.2. Replacement Parts List------------------------------- 187

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

1 Safety Precautions

1. Before servicing, unplug the AC power cord to prevent an electric shock.

2. When replacing parts, use only the manufacturer's recommended components.

3. Check the condition of the power cord. Replace if wear or damage is evident.

4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.

5. Before returning the serviced equipment to the customer, be sure to perform the following insulation resistance test to prevent the customer from being exposed to shock hazards.

1.1. For Service Technicians

• Repair service shall be provided in accordance with repair technology information such as service manual so as to prevent fires, injury or electric shock, which can be caused by improper repair work.

1. When repair services are provided, neither the products nor their parts or members shall be remodeled.

2. If a lead wire assembly is supplied as a repair part, the lead wire assembly shall be replaced.

3. FASTON terminals shall be plugged straight in and unplugged straight.

• ICs and LSIs are vulnerable to static electricity.

When repairing, the following precautions will help prevent recurring malfunctions.

1. Cover plastic parts boxes with aluminum foil.

2. Ground the soldering irons.

3. Use a conductive mat on worktable.

4. Do not grasp IC or LSI pins with bare fingers.

1.2. AC Caution

For safety, before closing the lower cabinet, please make sure of the following precautions.

1. The earth lead is fixed with the screw.

2. The AC lead is connected properly to power supply unit.

3. Wrap the earth lead around the core 5 times.

4. Wrap the AC lead around the core 5 times.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

1.3. Personal Safety Precautions

1.3.1. Moving Sections of the Unit

Be careful not to let your hair, clothes, fingers, accessories, etc., become caught in any moving sections of the unit. The moving sections of the unit are the rollers and a gear. There is a separation roller and a document feed roller which are rotated by the document feed motor. A gear rotates the two rollers. Be careful not to touch them with your hands, especially when the unit is operating.

1.3.2. Live Electrical Sections

All the electrical sections of the unit supplied with AC power by the AC power cord are live. Never disassemble the unit for service with the AC power supply plugged in.

CAUTION:

AC voltage is supplied to the primary side of the power supply unit. Therefore, always unplug the AC power cord before disassembling for service.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

1.4. Service Precautions

1.4.1. Precautions to Prevent Damage from Static Electricity

Electrical charges accumulate on a person. For instance, clothes rubbing together can damage electric elements or change their electrical characteristics. In order to prevent static electricity, touch a metallic part that is grounded to release the static electricity. Never touch the electrical sections such as the power supply unit, etc.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

2Warning

2.1. About Lead Free Solder (PbF: Pb free)

Note:

In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that contains lead.

We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn), Silver, (Ag), and Copper, (Cu).

This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.

Caution

PbF solder has a melting point that is 50° ~ 70° F, (30 ° ~ 40°C) higher than Pb solder. Please use a soldering iron with temperature

control and adjust it to 700° ± 20° F, ( 370 ° ± 10°C). In case of using high temperature soldering iron, please be careful not to heat

too long. PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100°F, (60 0 °C). If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possible and be

sure that any remaining is melted prior to applying the Pb solder. When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the opposite

side (See figure, below).

2.1.1. Suggested PBF Solder

There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper, (Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the manufacturer’s specific instructions for the melting points of their products and any precautions for using their product with other materials. The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

2.2. Insulation Resistance Test

1. Unplug the power cord and short the two prongs of the plug with a jumper wire.

2. Turn on the power switch.

3. Measure the resistance value with an ohmmeter between the jumpered AC plug and each exposed metal cabinet part (screw heads, control shafts, bottom frame, etc.). Note: Some exposed parts may be isolated from the chassis by design. These will read infinity.

4. If the measurement is outside the specified limits, there is a possibility of a shock hazard.

2.3. Battery Caution

CAUTION

Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s Instructions.

The lithium battery is a critical component (type No. CR2032). Please observe for the proper polarity and the exact location when replacing it and soldering the replacement lithium battery in.

2.4. Discarding of P. C. Board

When discarding P. C. Board, delete all personal information such as telephone directory and caller list or scrap P. C. Board.

3 Specifications

Applicable Lines: Public Switched Telephone Network

Document Size: Max. 216 mm in width

Max. 600 mm in length

Effective Scanning Width: 208 mm

Recording Paper Size: 216 × max. 30 m roll

Effective Printing Width: 208 mm

Transmission Time

: Approx. 15 s/page (Original mode)

Scanning Density: Horizontal: 8 pels/mm

Ver tical:

3.85 lines/mm - in standard resolution,

7.7 lines/mm - in fine/photo resolution,

15.4 lines/mm - in super fine resolution

Photo resolution: 64-level

Scanner Type: Contact Image Sensor

Printer Type: Thermal printing

Data Compression System: Modified Huffman (MH), Modified READ (MR)

Modem Speed: 9,600 / 7,200 / 4,800 / 2,400 bps; Automatic Fallback

Operating Environment: 5°C - 35°C, 20% - 80% RH (Relative Humidity)

Dimensions: Approx. height 121 mm × width 352 mm × depth 224 mm

Mass (Weight): KX-FT982: Approx. 2.7 kg

KX-FT984/KX-FT988: Approx. 2.8 kg

Power Consumption: Standby: Approx. 1.5 W (KX-FT982/KX-FT984)

Standby: Approx. 1.8 W (KX-FT988) Transmission: Approx. 13 W Reception: Approx. 30 W (When receiving a 20% black document) Copy: Approx. 35 W (When copying a 20% black document) Maximum: Approx. 110 W (When copying a 100% black document)

Power Supply: 220 V - 240 V AC, 50/60 Hz

Fax Memory Capacity

Approx. 28 pages of memory reception (Based on the ITU-T No. 1 Test Chart in standard resolution, with original mode.)

Voice Memory Capacity (KX-FT988 only):

Approx. 18 minutes of recording time including greeting message when no documents are in memory.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

Transmission speed depends upon the contents of the pages, resolution, telephone line conditions and capability of the other

party’s machine.

Transmission speed is based upon the ITU-T No. 1 Test Chart with original mode. If the capability of the other party’s machine is

inferior to your unit, the transmission time may be longer.

If an error occurs during fax reception, such as a paper jam or if the recording paper runs out, the fax and subsequent faxes will

be retained in memory.

Recording time may be reduced by the calling party’s background noise.

Note:

Design and specifications are subject to change without notice.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

4 General/Introduction

4.1. Optional Accessories

Model No. Item Specifications/Usage

KX-A106

Use only the included or specified recording paper. Using other recording paper may affect print quality and/or cause exces-

sive wear to the thermal head.

Standard thermal recording paper*

4.2. Translation Lists

4.2.1. Error Messages-Display

216 mm × 30 m roll, with 25 mm core

4.2.2. Error Messages-Report

4.2.3. Other-Display

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

5 Features

General

• LCD (Liquid Crystal Display) readout

• The display and reports will be in the selected language. (Spanish / English)

• Automatic Paper Cutter (KX-FT984/KX-FT988 only)

Facsimile

• Document memory

• Automatic document feeder (10 sheets)

• 64-Level halftone resolution Standard/Fine/Photo/Super Fine

• Broadcast

Integrated Telephone System

• Phonebook function (100 names)

• One-Touch Dial (10 stations)

• Caller ID compatible

• Monitor (KX-FT982/KX-FT984 only)

• Digital SP-Phone (KX-FT988 only)

Digital Answering System (KX-FT988 only)

• Voice Time/Day Stamp

• 18-Minutes recording time

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6 Technical Descriptions

6.1. Connection Diagram

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.2. General Block

The following is an outline of each device IC on the digital board. (Refer to General Block Diagram (P.14).).

1. ASIC (IC1)

Composed mainly of an address decoder and a modem control. Controls the general FAX operations. Controls the operation panel I/F. Controls the thermal head I/F and CIS I/F. Performs the image processing. CPU and Real time clock Provides the reset pulse for each of the major ICs.

2. Flash ROM (IC2)

Contains all of the program instructions on the unit operations. This memory is used mainly for the parameter working in the storage area.

3. Dynamic RAM (IC4)

This memory is used mainly for the parameter working in the storage area.

4. MODEM (IC5)

Performs the modulation and the demodulation for FAX communication.

5. Read Section

CIS image sensor to read transmitted documents.

6. Motor Driver (IC7)

Drives the transmission motor and the reception motor.

7. Thermal Head

Contains heat-emitting elements for dot matrix image printing.

8. Sensor Section

Composed of a cover open, a document set switch, a document top switch, a paper sensor switch, a jam sensor switch, and a hook sensor switch.

9. Power Supply Board Switching Section

Supplies +6V and +24V to the unit.

10. Flash MEMORY (IC6) (KX-FT988 only) Voice Prompt (TAM) D/L (DownLoad) area.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.2.1. General Block Diagram

6.3. Control Section

6.3.1. ASIC (IC1)

This custom IC is used for the general FAX operations.

1. CPU: This model uses a Z80 equivalent to the CPU operating at 24 MHz. Most of the peripheral functions are performed by custom-designed LSIs. Therefore, the CPU only works for processing the results.

2. RTC: Real Time Clock

3. DECODER: Decodes the address.

4. ROM/RAM I/F: Controls the SELECT signal of ROM or RAM and the bank switching.

5. CIS I/F: Controls the document reading.

Note:

This memory is incorporated into the ASIC (IC1) and used for the image processing.

6. IMAGE DATA RAM: This memory is programmed into the ASIC and uses 8 KB for the image processing.

7. THERMAL HEAD I/F: Transmits the recorded data to the thermal head.

8. MOTOR I/F: Controls the transmission motor which feeds the document. Controls the receiving motor which feeds the recording paper.

9. OPERATION PANEL I/F: Serial interface with Operation Panel.

10. I/O PORT: I/O Port Interface.

11. ANALOG UNIT: Electronic volume for the monitor. Sends beep tones, etc.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

Descriptions of Pin Distribution (IC1)

NO. SIGNAL I/O POWER SUPPLIED

1 VSSA1 GND POWER SOURCE (ANALOG GND) 2 VDDA 3.3 3.3V POWER SOURCE (ANALOG +3.3V) 3 AIN1 A 3.3V CIS IMAGE SIGNAL INPUT (ATN1) 4 AIN2 A 3.3V THERMISTOR TEMPERATURE WATCH INPUT 5 AIN3 A 3.3V LINE VOLTAGE DETECTION SIGNAL INPUT (DCIN) 6 AMON A 3.3V ANALOG SIGNAL MONITOR TERMINAL 7 VSS1 GND POWER SOURCE (GND) 8 X32OUT O 3.3V/BATT RTC (32.768KHz) CONNECTION

9 X32IN I 3.3V/BATT RTC (32.768KHz) CONNECTION 10 VDD (3.3V / B) ----- POWER SOURCE (+3.3V/LITHIUM BATTERY) 11 XBACKEN I 3.3V/BATT BACKUP ENABLE 12 XRAMCS O 3.3V/BATT XRAMCS 13 VDD (3.3V / B) ----- POWER SOURCE(+3.3V / LITHIUM BATTERY) 14 VDD (2.5V/B) ----- POWER SOURCE (+2.5V / LITHIUM BATTERY) 15 FTG O 3.3V SH SIGNAL OUTPUT FOR CIS (FTG) 16 F1 O 3.3V 01 SIGNAL OUTPUT FOR CIS (F1) 17 F2/OP O 3.3V OUTPUT PORT (HEADON) 18 FR/OP O 3.3V OUTPUT PORT (MDMRST) 19 CPC I 3.3V INPUT PORT (BELL/CPC) 20 RVN I 3.3V INPUT PORT (PAPER) 21 IRDATXD I 3.3V INPUT PORT (JAM) 22 IRDARXD O 3.3V OUTPUT PORT (HSTX MUTE) 23 TXD/IOP I 3.3V TXD 24 RXD/IOP I/O 3.3V RXD 25 RTS/IOP I 3.3V RTS 26 CTS/IOP I/O 3.3V CTS 27 VDD (2.5V)1 ----- POWER SOURCE (+2.5V) 28 TONE1 A 3.3V TONE OUTPUT 29 TONE2 A 3.3V TONE OUTPUT 30 VOLUREF/VOLU1 A 3.3V ANALOG REF VOLTAGE 31 VOLUOUT/VOLU2 A 3.3V VOLUME OUTPUT 32 VOLUIN/VOLU3 A 3.3V VOLUME INPUT 33 XNMI I 3.3V HIGH FIXED 34 FMEMDO/IOP O 3.3V OUTPUT PORT (LED ON) 35 VDD (3.3V)1 ----- POWER SOURCE (+3.3V) 36 VSS2 GND POWER SOURCE (GND) 37 VSS3 GND POWER SOURCE (GND)

DESCRIPTION

VOLTAGE

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

NO. SIGNAL I/O POWER SUPPLIED

DESCRIPTION

VOLTAGE 38 VDD (3.3V)2 ----- POWER SOURCE (+3.3V) 39 MIDAT/IOP I/O 3.3V PORT (TONE1EN) 40 MICLK/IOP O 3.3V OUTPUT PORT (MDMTXEN) 41 MILAT/IOP I/O 3.3V PORT (HSRXEN) 42 20KOSC/IOP O 3.3V OUTPUT PORT (PSHORT/ACK_EN) 43 XWAIT I 3.3V INPUT PORT (HOOK) 44 XHSTRD/IOP I 3.3V INPUT PORT (TEST) 45 XHSTWR/IOP O 3.3V OUTPUT PORT (DCN) 46 XOPRBE O 3.3V OUTPUT PORT (MFCS) 47 ADR15 O 3.3V CPU ADDRESS BUS 15 (NOT USED) 48 ADR14 O 3.3V CPU ADDRESS BUS 14 (NOT USED) 49 ADR13 O 3.3V CPU ADDRESS BUS 13 (NOT USED) 50 VDD (2.5V)2 ----- POWER SOURCE (+2.5V) 51 XOUT O 3.3V SYSTEM CLOCK (24MHz) 52 XIN I 3.3V SYSTEM CLOCK (24MHz) 53 VSS4 GND POWER SOURCE (GND) 54 VDD (3.3V)3 ----- POWER SOURCE (+3.3V) 55 XTEST O 3.3V 24MHz CLOCK 56 TEST1 I 3.3V HIGH FIXED 57 TEST2 I 3.3V HIGH FIXED 58 TEST3 I 3.3V HIGH FIXED 59 TEST4 I 3.3V HIGH FIXED 60 XMDMINT I 3.3V MODEM INTERRUPT 61 XMDMCS O 3.3V MODEM CHIP SELECT 62 XRAS/IOP O 3.3V DRAM ROW ADDRESS STROBE (RAS) 63 XCAS1/IOP O 3.3V DRAM COLUMN ADDRESS STROBE (CAS) 64 XCAS2/IOP I 3.3V PORT (SPMUTE) 65 XRESCS2 O 3.3V FLASH CHIP SELECT (XRESCS2) 66 DB3 I/O 3.3V CPU DATA BUS 3 67 DB2 I/O 3.3V CPU DATA BUS 2 68 DB4 I/O 3.3V CPU DATA BUS 4 69 DB1 I/O 3.3V CPU DATA BUS 1 70 DB5 I/O 3.3V CPU DATA BUS 5 71 VDD (3.3V)4 ----- POWER SOURCE (+3.3V) 72 VSS5 GND POWER SOURCE (GND) 73 VSS6 GND POWER SOURCE (GND) 74 VDD (3.3V)5 ----- POWER SOURCE (+3.3V) 75 DB0 I/O 3.3V CPU DATA BUS 0 76 DB6 I/O 3.3V CPU DATA BUS 6 77 DB7 I/O 3.3V CPU DATA BUS 7 78 XROMCS O 3.3V FLASH (IC2) CHIP SELECT 79 XRD O 3.3V CPU RD 80 XWR O 3.3V CPU WR 81 ADR0 O 3.3V CPU ADDRESS BUS 0 82 ADR1 O 3.3V CPU ADDRESS BUS 1 83 ADR2 O 3.3V CPU ADDRESS BUS 2 84 ADR3 O 3.3V CPU ADDRESS BUS 3 85 ADR4 O 3.3V CPU ADDRESS BUS 4 86 ADR5 O 3.3V CPU ADDRESS BUS 5 87 VSS7 GND POWER SOURCE (GND) 88 VDD (2.5V)3 ----- POWER SOURCE (+2.5V) 89 ADR6 O 3.3V CPU ADDRESS BUS 6 90 ADR7 O 3.3V CPU ADDRESS BUS 7 91 ADR8 O 3.3V CPU ADDRESS BUS 8 92 ADR9 O 3.3V CPU ADDRESS 9 93 ADR10 O 3.3V CPU ADDRESS 10 94 ADR11 O 3.3V CPU ADDRESS 11 95 ADR12 O 3.3V CPU ADDRESS 12 96 RBA0 O 3.3V ROM/RAM BANK ADDRESS 0 97 RBA1 O 3.3V ROM/RAM BANK ADDRESS 1 98 RBA2 O 3.3V ROM/RAM BANK ADDRESS 2 99 RBA3 O 3.3V ROM/RAM BANK ADDRESS 3

100 RBA4 O 3.3V ROM/RAM BANK ADDRESS 4 101 RBA5 O 3.3V ROM/RAM BANK ADDRESS 5 102 RBA6/IOP O 3.3V OUTPUT PORT (NC) 103 STB1 O 3.3V STROBE SIGNAL OUTPUT TO THERMAL HEAD

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

NO. SIGNAL I/O POWER SUPPLIED

VOLTAGE 104 STB2 O 3.3V STROBE SIGNAL OUTPUT TO THERMAL HEAD 105 STB3 O 3.3V OUTPUT PORT (NC) 106 XRESET I 3.3V RESET INPUT 107 VDD (3.3V)6 ----- POWER SOURCE (+3.3V) 108 VSS8 GND POWER SOURCE (GND) 109 VSS9 GND POWER SOURCE (GND) 110 VDD (3.3V)7 ----- POWER SOURCE (+3.3V) 111 XORESET O 3.3V NOT USED 112 VDD(5V) ----- POWER SOURCE (+5V) 113 VSS10 GND POWER SOURCE (GND) 114 XRESETI I 3.3V RESET INPUT 115 XWDERR O 3.3V WATCHED ERROR OUTPUT SIGNAL 116 THDAT O 3.3V RECORDED IMAGE OUTPUT (THDAT) 117 THCLK O 3.3V CLOCK OUTPUT FOR DATA TRANSFER (THCLK) 118 THLAT O 3.3V PULSE OUTPUT FOR DATA LATCH (THLAT) 119 STBNP I 3.3V INPUT PORT (MOT-POS) 120 RM0/IOP O 3.3V MOTOR A PHASE 121 RM1/IOP O 3.3V MOTOR B PHASE 122 RM2/IOP O 3.3V MOTOR /A PHASE 123 RM3/IOP O 3.3V MOTOR /B PHASE 124 RXE/IOP O 3.3V MOTOR ENABLE 125 TMO O 3.3V OUTPUT PORT (R1) 126 VDD (2.5V)4 ----- POWER SOURCE (+2.5V) 127 VSS11 GND POWER SOURCE (GND) 128 TM1/IOP O 3.3V OUTPUT PORT (R2) 129 TM2/IOP O 3.3V OUTPUT PORT (CISON) 130 TM3/IOP O 3.3V OUTPUT PORT (RLY) 131 TXE/IOP I 3.3V INPUT PORT (CUT_POS) 132 KSTART O 3.3V OPERATION PANEL CONTROL 133 KLATCH O 3.3V OPERATION PANEL CONTROL 134 KSCLK O 3.3V OPERATION PANEL CONTROL 135 KTXD O 3.3V OPERATION PANEL CONTROL 136 KRXD I 3.3V OPERATION PANEL CONTROL 137 FMEMCLK/IOP O 3.3V OUTPUT PORT (OPRESET) 138 FMEMDI/IOP O 3.3V OUTPUT PORT (NC) 139 ADSEL1 O 3.3V CHANNEL SELECT SIGNAL FOR AIN2 140 VDDA (2.5V) 2.5V POWER SOURCE (ANALOG +2.5V) 141 VREFB A 3.3V A/D CONVERTER'S ZERO STANDARD VOLTAGE

OUTPUT 142 VCL A 3.3V ANALOG PART STANDARD VOLTAGE SIGNAL 143 VREFT A 3.3V A/D CONVERTER'S FULL SCALE VOLTAGE OUTPUT 144 VSSA2 GND POWER SOURCE (ANALOG GND)

DESCRIPTION

Connection to operation reset circuit

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.3.2. Flash Memory (IC2)

This 512KB ROM (FLASH MEMORY) carries a common area of 32KB and bank areas which each have 8KB (BK4~BK63). The addresses from 0000H to 7FFFH are for the common area and from 8000H to 9FFFH are for the bank areas.

6.3.3. Dynamic RAM (IC4)

The DRAM serves as CPU and receives memory. The address is F200H~F3FFH (DRAM access window 1) and F600H~F7FFH (DRAM access window 2).

6.3.4. Reset Circuit (Watch dog timer)

The output signal (reset) from pin 4 of the voltage detect IC (IC3) is input to the ASIC (IC1) 114 pin.

1. During a momentary power interruption, a positive reset pulse of 50~70 msec is generated and the system is reset completely.

2. The watch dog timer, built-in the ASIC (IC1), is initialized by the CPU about every 1.5 ms. When a watch dog error occurs, pin 115 of the ASIC (IC1) becomes low level. The terminal of the 'WDERR' signal is connected to the reset line, so the 'WDERR' signal works as the reset signal.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.3.5. RTC Back up Circuit

1. Function This unit has a lithium battery (BAT1) which works for the Real Time Clock (RTC, Integrated into ASIC:IC1). The RTC continues functioning, even when the power switch is OFF, backed up by a lithium battery.

2. Circuit Operation When the power is turned ON, power is supplied to RTC (IC1). At this time, the voltage at pin 14 of RTC (IC1) is +3.3V. When the power is turned OFF, the battery supplies the power to RTC through JS1, R30, D14. At that time, the voltage at pin 14 of IC1 are about +2.5V. When the power is OFF and the +5V and +3.3V voltages decrease, the LOW is input to pin 114 of IC1. Pin 111 of IC1 outputs the reset signals. Pin 11 of IC1 become low, then RTC (IC1) go into the back up mode, when the power consumption is lower.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.3.6. Supervision Circuit for the Thermal Head Temperature

1. Function The thermistor changes the resistor according to the temperature and uses the thermistor's characteristics. The output of pin 139 of IC1 becomes a low level. Then when it becomes a high level, it triggers point A. In point C, according to the voltage output time, the thermal head's temperature is detected. After the thermal head temperature is converted to voltage in B, it is then changed to digital data in the A/D converter inside IC1. The CPU decides the strobe width of the thermal head according to this value. Therefore, this circuit can keep the thermal head at an even temperature in order to stabilize the printing density and prevent the head from being overheated.

REFERENCE:

Thermal Head (P.23)

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.4. Facsimile Section

6.4.1. Image Data Flow During Facsimile Operation

Copy (Fine, Super-Fine, Photo)

1. Line information is read by CIS (to be used as the reference white level) via route (1), and is input to IC1. Refer to Block Diagram (P.22)

2. In IC1, the data is adjusted to a suitable level for A/D conversion in the Analog Signal Processing Section, and via route (2) it is input to A/D conversion (8 bit). After finishing A/D conversion, the data is input to the Image Processing Section via route (3). Then via route (4) and route (5), it is stored in RAM as shading data.

3. The draft’s information that is read by CIS is input to IC1 via route (1). After it is adjusted to a suitable level for A/D conversion via route (2), the draft’s information is converted to A/D (8 bit), and it is input to the Image Processing Section. The other side, the shading data which flows from RAM via route (6) and route (7), is input to the Image Processing Section. After finishing the draft’s information image processing, white is regarded as "0" and black is regarded as "1". Then via routes (4) and (5), they are stored in RAM.

4. The white/black data stored as above via routes (6) and (8) is input to the P/S converter. The white/black data converted to serial data in the P/S converter is input to the Thermal Head via route (9) and is printed out on recording paper.

Note:

Fine: Reads 3.85 lines/mm Super Fine: Reads 7.7 lines/mm Photo: Reads 15.4 lines/mm

Transmission

1. Same processing as Copy items 1 - 3.

2. The data stored in the RAM of IC1 is output from IC1 via routes (6) and (10), and is stored in the system bus. Via route (11), it is stored in the communication buffer inside DRAM (IC4).

3. While retrieving data stored in the communication buffer synchronous with the modem, the CPU (inside IC1) inputs the data to the modem along route (12), where it is converted to serial analogue data and forwarded over the telephone lines via the NCU Section.

Reception

1. The serial analog image data is received over the telephone lines and input to the modem via the NCU section, where it is demodulated to parallel digital data. Then the CPU (IC1) stores the data in the communication buffer DRAM (IC4) along route (11).

2. The data stored in DRAM (IC4) is decoded by the CPU (IC1) via route (12), and is stored in RAM via routes (13) and (5).

3. Same processing as Copy item 4.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.4.2. Block Diagram

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.4.3. Thermal Head

1. Function This unit utilizes state of the art thermal printer technology. The recording paper (roll paper) is chemically processed. When the thermal head contacts this paper it emits heat momentarily, and black dots (appearing like points) are printed on the paper. If this continues, letters and/or diagrams appear, and the original document is reproduced.

2. Circuit Operation There are 27 driver ICs aligned horizontally on the thermal head and each one of these ICs can drive 64 heat emitting registers. This means that one line is at a density of 64×27=1728 dots=(8 dots/mm). White/Black (white=0, black=1) data in one line increments is synchronized at IC1 pin 117 (THCLK), and sent from IC1 pin 116 (THDAT) to the shift register of the ICs. The shift registers of the 27 ICs are connected in series, and upon the shift of dot increment 1728, all the shift registers become filled with data, and a latch pulse is emitted to each IC from IC1 pin 118 (THLAT).With this latch pulse, all the contents of the shift registers are latched to the latch registers. Thereafter, through the addition of strobes from the IC1 pins (103 - 104) only black dot locations (=1) among latched data activates the driver, and the current passes to heat the emitting body causing heat emission. Here, the two line strobes, STB1 and STB2, impress at intervals of 9.216 msec, as required for one-line printout. The sequence is shown on the next page. [Moreover, for the strobe width, the thermistor value inside the thermal head is detected according to IC1 pin 4. Depending on that value, the strobe width is recorded in FLASH (IC2). Accordingly, the strobe width is determined. When the thermal head is not used, the IC1 (17, HEADON) becomes low, Q6 turns OFF, Q7 turns OFF, and the +24 V power supply for the thermal head driver is not impressed to protect the IC.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.4.4. Scanning Block

The scanning block of this device consists of a control circuit and a contact image sensor made up of a celfoc lens array, a light source, and photoelectric conversion elements.

When an original document is inserted and the start button pressed, pin 129 of IC1 goes to a low level and the transistor Q14 turns on.This applies voltage to the light source to light it. The contact image sensor is driven by each of the FTG-F1 signals output from IC1, and the original image illuminated by the light source undergoes photoelectric conversion to output an analogue image signal (AIN). The analogue image signal is input to the system ASIC on AIN1 (pin 3 of IC1) and converted into 8-bit data by the A/D converter inside IC1. Then this signal undergoes digital processing in order to obtain a high-quality image.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.4.5. Stepping Motor Drive Circuit

1. Function One individual stepping motor is used for transmission and reception. It feeds the document or recording paper synchronized for reading or printing.

2. Circuit Operation During motor drive, ASIC IC1 pin 124 becomes a high level, and Q2 and Q1 go ON as a result. +24 V is supplied tothe motor coil. Stepping pulses are output from ASIC IC1, causing driver IC7 to go ON. The motor coil is energized sequentially in 2 phase increments or 1-2 phase increments, which causes a 1-step rotation. A 1-step rotation is 0.13mm of recording paper or document paper. The timing chart is below.

Stepping Motor Phase Pattern

Function Mode Phase Pattern Speed

Copy Fine/Photo 1-2 432 pps

Super Fine 1-2 216 pps

FAX STD 2 432 pps

Fine/Photo 1-2 432 pps

Super Fine 1-2 216 pps

——— Paper Feed 2 432 pps

When the motor is OFF, ASIC IC1 pin 124 becomes a low level and Q2 and Q1 also turns OFF. Instead of +24V, +5V is supplied through D11 so that the motor is held in place.

6.5. Sensors and Switches

All of the sensors and switches are shown below.

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

Sensor Circuit

Location

DIGITAL CN5 Motor Position Sensor [CALL SERVICE]

ANALOG SW101 Cover Open / Paper Sensor [COVER OPEN] and [CHECK PAPER]

Operation Panel SW338 Document Top Sensor [REMOVE DOCUMENT]

Sensor Sensor or Switch Name Error Message (*1)

CN6 Cutter Position Sensor

SW102 Hook Sensor ————

SW103 JAM Sensor [PAPER JAMED]

SW339 Document Set Sensor [CHECK DOCUMENT]

Note:

• SEE Test Mode (P.55) for Sensor Check (#815).

• (*1) Refer to Translation Lists (P.10) for display.

[PAPER JAMED]

(KX-FT984/KX-FT988 only)

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.5.1. Motor Position Sensor

This sensor is a detection switch for recording the position of the CAM.

Signal (IC1-119 pin) Home position Low level Other High level

6.5.2. Cutter Position Sensor (KX-FT984/KX-FT988 only)

Signal (IC1-131 pin) Home position Low level Other High level

6.5.3. Cover Open / Paper Sensor (SW101)

When the recording paper is loaded on the print head and the cover is closed, the paper sensor SW turns ON, and the input signal of IC1-20 pin becomes a low level. Usually, the SW turns OFF, and the input signal of IC1-20 pin becomes a high level.

Sensor Signal (IC1-20 pin) Set recording paper and cover is closed ON Low level No recording paper or cover is open OFF High level

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.5.4. Hook Sensor (SW102)

When the handset is lifted, the switch turns ON, and the signal at pin 43 of IC1 becomes low. When the handset is returned, the switch turns OFF, and the signal at pin 43 of IC1 becomes high.

Sensor SW Signal (IC1-43 pin) ON-Hook OFF High level OFF-Hook ON Low level

6.5.5. Jam Sensor (SW103)

The JAM sensor is a detection switch for determining whether the recording paper edge is in the correct position or not. If the recording paper cannot be detected correctly at the JAM sensor position even when recording paper is present, then JAM is displayed. If the recording paper is at the sensor position, then the switch turns on the IC1-21 pin switches to a high level.

Signal (IC1-21 pin) Paper Low level No paper High level

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B

6.5.6. Document Top Sensor (SW338)

When a document is brought to the read position, the SW becomes ON, and the input signal of IC301-5 pin (Operation Board) becomes a low level. When there is no document at the read position, the SW becomes OFF, and the input signal of IC301-5 pin (Operation Board) becomes a high level.

Sensor SW Signal (IC301-5 pin) Out of the Read Position OFF High level At the Read Position ON Low level

6.5.7. Document Set Sensor (SW339)

When a document is set, the SW becomes ON, and input signal of IC301-6 pin (Operation Board) becomes a low level. When there is no document, the SW becomes OFF, and the input signal of IC301-6 pin (Operation Board) becomes a high level.

Sensor SW Signal (IC301-6 pin) No document OFF High level Set document ON Low level

+ 164 hidden pages