Panasonic KX-FP320E, KX-FM330E Service manual

KX-FP320E/KX-FM330E

ORDER NO. KM79908303A2

Plain Paper FAX with Answering Machine

KX-FP320E

Simplified

Multi-Function Plain Paper Facsimile

KX-FM330E

Please use this manual together with the Service Manual for model No. KX-FP320G/KX-FM330G, order No.KM79908300C2. This Service Manual indicates the main differences between; Original KX-FP320G/KX-FM330G and KX-FP320E/KX-FM330E.

WARNING

This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.

(Model KX-FP320E/KX-FM330E)

KX-FP320E/KX-FM330E

BATTERY CAUTION

SAFETY CAUTIONS FOR LITHIUM BATTERY

(FOR UNITED KINGDOM) THE LITHIUM BATTERY IS A CRITICAL COMPONENT TYPE NUMBER CR2032 (BATT) MANUFACTURED BY MATSUSHITA

CR2032 (BATT) SONY

IT MUST NEVER BE SUBJECTED TO EXCESSIVE HEAT OR DISCHARGE. IT MUST THEREFORE ONLY BE FITTED IN EQUIPMENT DESIGNED SPECIFICALLY FOR ITS USE.

REPLACEMENT BATTERIES MUST BE OF AN APPROVED TYPE AND MANUFACTURER AS INDICATED ABOVE. THEY MUST BE FITTED IN THE SAME MANNER AND LOCATION AS THE ORIGINAL BATTERY, WITH THE CORRECT POLARITY CONNECTIONS OBSERVED.

DO NOT ATTEMPT TO RE-CHARGE THE OLD BATTERY OR RE-USE IT FOR ANY OTHER PURPOSE. IT SHOULD BE DISPOSED OF IN WASTE PRODUCTS DESTINED FOR BURIAL RATHER THAN INCINERATION.

WARNING THE LITHIUM BATTERY IN THIS EQUIPMENT MUST ONLY BE REPLACED BY QUALIFIED PERSONNEL.

WHEN NECESSARY, CONTACT YOUR LOCAL PANASONIC SUPPLIER.

FITTING A PLUG TO THE MAINS LEAD

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A5 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has rating of 5 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover

the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET. If a new plug is to be fitted please observe the wiring code as shown below.

WARNING : THIS APPLIANCE MUST BE EARTHED. IMPORTANT : The wires in this mains leads are coloured in accordance with the following code:

Green-and-yellow: Earth Blue: Neutral

Brown: Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW. The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. How to replace the fuse : Open the-fuse compartment with a screwdriver and replace the fuse and fuse cover.

FUSE

(Model KX-FP320E/KX-FM330E)

1.12.2. CONTROL PANEL (Change from original page 10)

• To erase recorded messages.

• To erase your own greeting messages.

• To turn the AUTO ANSWER mode on/off.

• For the Caller ID service.

• To print a quick reference.

• To adjust volumes.

• To select feature settings during programming.

VOLUME

RINGER / SPEAKER

ABC DEF

JKLGHI MNO

Dial keypad

TUVPQRS

TONE SLOW QUICK

WXYZ

RECALL

REDIAL /PAUSE

MUTE

• To initiate or exit programming.

• To select a resolution.

Display panel

TAD/FAX ON

RESOLUTION

STOP

MEMORY% CALLS

START / SET /

• To play recorded messages.

• To record your own greeting messages.

• To record memo messages or telephone conversations.

• To store or edit names and telephone numbers.

• To choose "Collated" or "Uncollated" in the copy mode.

ERASE

RECORD

PLAY MESSAGES

1 6

HYPHEN

DIRECTORY PROGRAM

2 7 3 8

FWD

SKIP

MESSAGES

BACK

REPEAT

INSERT

SECRET

KX-FP320E/KX-FM330E

• To check the amount of remaining film.

• For transmission to multiple stations.

FILM REMAINING

4 9 5

NAME/TEL NO.

LOWER

MIC

• To insert a hyphen.

• For the One-Touch Dial.

• To insert one character or one space.

• To keep the telephone number secret.

• To confirm a stored telephone number.

• To select stations 6–10 for the One Touch Dial.

• To change from pulse to tone during dialling.

• For slow playback.

• For quick playback.

•

pp p

• Recall button.

• To redial the last number dialled.

• To insert a pause during dialling.

• For voice muting.

• To stop an operation or cancel programming.

• To talk with the other party when using the speakerphone.

• To search for a stored name.

• To select characters during programming.

• To select the basic features during programming.

• To skip and/or repeat recorded messages in the answering device.

• To select an enlargement/reduction rate in the copy mode.

• To initiate fax transmission, reception or copying.

• To store a setting during programming.

(Model KX-FP320E/KX-FM330E)

KX-FP320E/KX-FM330E

1.13. CONNECTIONS (Change from original page 11)

Connect the handset cord.

Connect the telephone line cord.

Connect the mains lead.

• When the power is turned on for the

first time, the unit will print some basic information.

To Household Mains Supply (220-240 V, 50 Hz)

To B.T. socket

Note:

• When you operate this product, the power outlet should be near the product and easily accessible.

• If the following message is displayed when the unit is plugged in, the recording paper set lever will be released.

Mains lead

Handset cord

Telephone line cord

Display:

Move the lever back.

• Telephone line connection is TNV (Telecommunication Network Voltage).

CHECK LEVER

1.14.7. TO SELECT CHARACTERS WITH THE DIAL KEY PAD (Change from original page 19)

Keys

1 2 3 4 5 6 7 8 9

M P

[

]

{

}

+ c

rs7

yz9

Characters

/=, .

;

STOP

0()<>! "#$%

HYPHEN key (To insert a hyphen.) INSERT key (To insert a one character or one space.) Delete key (To delete a character.)

key (To move the cursor to the left.) key (To move the cursor to the right.)

To enter another character using the same number key, move the cursor to the next space.

(Model KX-FP320E/KX-FM330E)

(Change from original page 27)

DISPLAY MESSAGE CAUSE AND REMEDY

KX-FP320E/KX-FM330E

NO FAX REPLY

PAPER JAMMED

PLEASE WAIT

POLLING ERROR

REDIAL TIME OUT

REMOVE DOCUMENT

TRANSMIT ERROR

UNIT OVERHEATED

MASSAGE FULL

The other party’s fax machine is busy or has run out of recording paper. Try again.

A recording paper jam occurred under the film cartridge. Clear the jammed paper.

[If the printout jams, please refer to Fig. a on the next page.]

The unit is checking that there is no slake on the film. Wait a while.

The other party’s fax machine dose not provide the polling function. Check with the

other party.

The other party’s fax machine is busy or has run out of recording paper. Try again.

The document is jammed. Remove the jammed document.

Attempted to transmit a document longer than 600 mm. Press STOP to remove the document. Divide the document into two or more sheets and try again. [Alternatery, turn off service code #559 to enable sending of documents longer than 600 mm.]

A transmission error occurred. Try again.

The unit is too hot. Let the unit cool down. [If many copies are nearly all black, this message will be displayed. When this occurs, open the front cover and let the unit cool down.]

There is no room left in memory to record a voice message. Erase some or all of the message.

KX-FM330 only

PC FAIL OR BUSY

Note:

The explanations given in the [ ] are for servicemen.

The fax function cannot be operated by the PC. The RS232C cable is not connected correctly, or the software is not running on the PC. [If many copies are nearly all black, this message will be displayed. When this occurs, open the front cover and let the unit cool down.]

(Model KX-FP320E/KX-FM330E)

KX-FP320E/KX-FM330E

2. Sometimes there is a transmit problem (Change from original page 46)

TX Problem

Is the document pre-fed?

YES

Does TX start? (Does it start feeding?)

YES

The document goes through.

Confirm if the sent image on the RX side has many errors.

"Transmit Error"

Increase the "596:Transmit level set" from -11 dBm to -5 dBm or same value.

Ask the other party to change the RX equalizer & increase the TX level.

Message on LCD

Is auto dialing used to send?

Did you press the START key immediately after dialing?

Decrease the TX level from -11 dBm to - 15 dBm or same value.

YES

Check the other party's machine. (Out of paper, auto answer off, etc.)

• Increase the "596:Transmit level set" from -11 dBm to -5 dBm or some value. OR

• Decrease the "596:Trans mit level set" from -11 dBm to -13 dBm . Try again.

Change the "717:Transmit speed select " to 7200,4800 or 2400 bps.

Note:

“596: Transmit level set” represents a service code. (Refer to 2.4.4. Service Function Table.) Refer to the Service Function Table.

12000,9600

• Decrease the "596: Trans-

mit level set" from -11 dBm to -15 dBm. Try again.

Ask the RX party to increase the parameter of the RX error line value to more than the current setting.

(Not available)

(Model KX-FP320E/KX-FM330E)

Check the current TX level.

Change the "594: Oversea DIS detection" to "Detect at the 2nd time".

Confirm that "592:CNG TX select" is set to "ALL".

Ask the other party to increase the TX level.

3. Receive problem (Change from original page 47)

Confirm the following before starting troubleshooting. Is the recording paper installed properly? Refer to Remarks.

RX problem

KX-FP320E/KX-FM330E

Can something be RX?

Which mode?

EXT. TAM mode

(When connected to an answering machine during EXT. TAM.)

Can not RX from Ricoh machines which have the G1,G2 and G3 modes.

YES

TEL/FAX mode

FAX mode TEL mode

YES

Are there many errors on the image?

NO: Looks OK.

Increase the "595: RX error limit value" to some value.

YES

Is the EXT TEL off-hook before the ringing stops?

Is the FAX ring count (#07) 2, 3 or 4?

Change the FAX ring count to 1.

YES

Change the "718: Receive speed select" to 12000, 9600, 7200, 4800 or 2400 bps.

Ask the sender to change:

• Increase the "596: Transmit level set".

YES

Can't RX on international call or long distance call?

YES

Re-record the answering machine OGM in a quiet room. (The OGM shouldn?t have back ground noise.)

Ask the sender to change:

• Send manually.

Note:

“596: Transmit level set” represents a service code. (Refer to 2.4.4. Service Function Table.) Refer to the Service Function Table.

Ask the sender to change:

• Send manually using " ".

Change the "718:Receive speed select" to 12000, 9600, 7200, 4800 or 2400 bps.

Ask the sender to change:

• Increase the TX level.

• Change the TX equalizer.

(Model KX-FP320E/KX-FM330E)

Increase the "593: Time between CED & 300 bps" to some value.

Error code No. 68 (Echo)?

NO YES

Decrease the "596:Transmit level set" from -11 dBm to

-13 dBm or some value.

Note: "596: Transmit level set"

represents a service code. (Refer to 2.4.4. Service Function Table.) Refer to the Service Function Table.

KX-FP320E/KX-FM330E

2. Program Mode Table (Change from original pages 65~66)

Code Func ti on Set Value Defau lt Remote Setting

001 Set date and time dd/ mm/yy hh:mm AM/PM (01/Jan /99) NG 002 Your logo --------- --------- NG 003 Your tel epho ne n umber --------- (None) NG 004 Transmission report mode 1:Error / 2:ON / 3:OFF ERROR OK 006 FAX ring co unt 1~4 2 NG

TAD/FAX ring c oun t 1~4/T OLL S AVE R/RINGER O FF 2 NG

Not available in TEL/FAX --------- -------- NG 010 Recor di ng time 1:L ONG / 2:SHORT LONG OK 011 Remote ANS ID --------- ID=111 NG 013 Dialing mode 1:PULSE / 2:TONE TONE OK 014 PC link (KX-FM330 ONLY) 1:O N / 2:OFF O N OK 015 Memory XMT 1:ON / 2:OFF OFF OK 022 Auto journal print 1:ON / 2:OFF O N OK 023 Overseas mode ON / OFF OFF NG 025 Delayed t ransmission ON / OFF OFF NG 026 Auto caller list 1:ON / 2:OFF ON OK 030 Silent FAX recognition ring 3 to 6 rings 3 OK 036 Rx r eduction 1:7 2% / 2:86% / 3:92% / 4: 1 00% 92% OK 039 LCD contrast 1:NORMAL / 2:DARK ER NORMAL OK 041 Remote FAX activation code 1:O N / 2: OF F ON / ID=*9 NG 042 Messa ge a l ert 1:O N / 2: OFF OFF OK 043 REC. time alert 1:ON / 2: OFF OFF OK 044 Receive alert 1:ON / 2:OFF ON OK 045 Recall mode T_BR, E_RE T_BR OK 046 Friendly rcv . 1:ON / 2:OFF ON OK 047 FAX voice guidance 1:ERRO R / 2:ON / 3:OFF ON OK 054 Common gre etin g MSG. REC. time 1:1 6s / 2:60s 16s OK 060 M essage transfer 1:MESSAG E / 2:PAG ER / 3:OFF OFF NG 061 Transfer greeting 1:CHECK / 2:RECORD / 3:E RASE CHECK NG 067 ICM monitor 1:ON / 2:OFF ON OK 068 ECM Communi c ation 1: ON / 2:O FF ON OK 070 FAX pager call ON / OFF OFF NG 076 FAX tone 1:ON / 2:OFF ON OK 077 Auto answer mode 1:TAD/FA X 2: FAX ONLY 3 : TEL/FAX TAD/FAX OK 078 TE L/FAX delay e d ring 1 t o 4 rings 2 OK 079 Film detection 1:ON / 2:OFF ON OK 080 Set default YES / NO NO NG 501 Pause ti me set 001~600 x 100msec 35 OK 502 Fla sh time set 01~99 x 10msec 80 OK 503 Dial speed 1:10pps / 2 :20 pps 10 OK 520 CED frequency select 1:2 100Hz / 2:1100Hz 2100 OK 521 International mode select 1:ON / 2:OFF ON OK 522 Auto standby select 1:ON / 2:OF F O N OK 523 Receive equalizer select 1:0.0km / 2:1.8km / 3 :3.6k m / 4:7.2k m 0km OK 524 Transmission equalizer select 1:0 .0km / 2:1. 8km / 3:3.6km / 4:7.2k m 0km OK 533 Setting the number of t i mes that

message transfer is redialed 534 Setting of the message transfer/pager

call redial i nterv al 550 Memory clear --------- --------- NG 551 ROM check --------- --------- NG 552 DTMF signal tone test 1:ON / 2:OFF OFF NG 553 Monitor on FAX communicati on select 1:OFF / 2:Phase B / 3:ALL OF F OK 554 Modem test --------- --------- NG 555 Scanner t est --------- --------- NG 556 Motor test --------- --------- NG 557 LED test --------- --------- NG

00~99 03 OK

001~999 065 OK

(Model KX-FP320E/KX-FM330E)

KX-FP320E/KX-FM330E

Code Function Set Value Default Remote

Setting 561 Key test --------- --------- NG 570 Break % select 1:61% / 2:67% 67% OK 571 ITS auto redial time set 00~99 03 OK 572 ITS auto redial line disconnection time set 001~999 065 OK 573 Remote turn-on ring number set 01~99 20 OK 576 K Break detect 1:ON / 2:OFF ON OK 57 9 Dete ct b ell type 1:TYPE 1 / 2:TYPE 2 TYPE 1 OK 580 TAM continuous tone detection 1:ON / 2:OFF ON OK 590 FAX auto redial time set 00~99 03 OK 591 FAX auto redial line disconnection time set 001~999 065 OK 59 2 CNG tran s m it s e lect 1:OFF / 2:ALL / 3:AUTO ALL OK 593 Time between CED and 300 bps 1:75ms / 2:500ms / 3:1sec 75ms OK 59 4 Overs ea s DIS detection s elect 1:1s t / 2:2nd 1s t OK 595 Receive error limit value set 001~999 100 OK 596 Transmit level set -15~00dBm -11 OK 598 Receiving Sensitivity -20~48dBm 48 OK 624 AT ring time out (KX-FM330E only) 1: 3sec / 2: 5sec 3sec OK 717 Transmit speed select 1:14400 / 2:1200 0 / 3:9600 / 4:7200 /

5:4800 / 6:2400

718 Receive speed select 1:14400 / 2:12000 / 3:9600 / 4:7200 /

5:4800 / 6:2400 719 Ringer off in TEL/FAX mode 1:ON / 2:OFF ON OK 721 Pouse tone detect 1:ON / 2:OFF ON OK 722 Redial tone detect 1:ON / 2:OFF ON OK 724 PC SND busy tone detect (KX-FM330E

only) 732 Auto disconncect 1: 350ms / 2:1800ms / 3:OFF 35 0m s ec OK 745 Power ON film feed 1:ON / 2:OFF ON OK 76 3 CNG detect tim e for friend ly recep tion 1:10 s / 2:20s / 3:30 s 30 s OK 771 T1 timer 1:35s / 2:60s 35s OK 775 Monitoring of message transfer 1:ON / 2:OFF OFF OK 78 2 Cal ler ID AC trans mit s elect 1:ON / 2:OFF OFF OK 815 Sensor & VOX test --------- --------- NG 852 Print test pattern --------- --------- NG 853 Top m argin 1~9 --------- OK 854 Left margin 1~8 --------- OK 861 A4 size set 1:ON / 2:OFF ON OK 880 Special service journal 1:Start --------- OK 890 TEL/FAX ring back tone 1:ON / 2:OFF ON OK 89 5 TEL /FAX Receive mode 1:TAD/FAX / 2:FAX FAX OK

1:ON / 2:OFF ON OK

14400bps OK

OK means can set. NG means can not set.

Note:

Refer to 2.4.4. SERVICE FUNCTION TABLE for descriptions of the individual codes.

Example:

If you want to set value in the 004 Transmission report mode, press the dial key number 1, 2 or 3 corresponding to the Set Value you want to select. (1:ERROR/2:ON/3:OFF)

(Model KX-FP320E/KX-FM330E)

KX-FP320E/KX-FM330E

2.3.3.5. Analog Board Section (Change from original page 81)

This chapter provides the testing procedures required for the analog parts. A signal route to be tested is determined depending upon purposes. For example, the handset TX route begins at the handset microphone and the signal is output to the telephone line. The signal mainly flowing on this route is analog. You can trace the signal with an oscilloscope. The signal flow on each route is shown in the Check Sheet here. If you find a specific problem in the unit, for example if you cannot communicate with the H/S, trace that signal route locally with the following Check Sheet and locate the faulty point.

CHECK SHEET

(SYMPTOM) ITEMS TO CHECK

SP-PHONE Tx

SP-PHONE Rx

Handset Tx

Handset Rx

Greeting for TEL LINE MSGS for TEL LINE

DTMF monitor

Greeting for TEL LINE

MSGS for TEL LINE DTMF for TEL LINE FAX Tx

(TONE 1)

Dummy Ring

and T AM Beep

(TONE 1)

RINGING

Alarm / Beep / Key tone

Speaker

Handset

Back tone to Line

Signal

I N O U T

MIC-R110-C79-IC5(51-71)-C145-CN7(7)-{CN501(7)-R707-R913-C930-IC505(36-69)-C941C805-R806-IC803(2-1)-C942-CN501(10)}-CN7(10)-C126-R159-IC5(73-63)-C53-R73-IC10(2-1)-C37R58-R57-T1-TEL LINE

TEL LINE-T1-R59-C44-IC10(6-7)-J33-C56-C59-R85-R89-C64-IC2(1-2)-C68- CN7(9)-{CN501(9)-C701-IC801(3-4)-C943-J604-C603-IC505(60-47)-C925-R912-R708-CN501(8)}CN7(8)-C127-R160-IC5(75-41)-C100-R139-IC5(40-38)-C91-R132-IC3(4-5, 8)-SPEAKER

MIC---L35-R135-C94---IC5(52,54-63)-C53-R73-IC10(2-1)-C37--R58---R57-T1-TEL LINE

L38-R134-C93

TEL LINE -T1-R59-C44-IC10(6-7)-

---C84-L37---SPEAKER L36

{IC505(47)-C925-R912-R708-CN501(8)}-CN7(8)-C127-R160-IC5(75-41)-C100-R139-IC5(40-38) C91-R132-IC3(4-5,8)-Speaker

{IC505(69)-C941-C805-R806-IC803(2-1)-C942-CN501(10)}-CN7(10)-C126-R155-IC5(76-45,46) C84-L37 Speaker L36

{IC505(69)-C941-C805-R806-IC803(2-1)-C942-CN501(10)}-CN7(10)-C126-R159-IC5(73-63)-C53-R73IC10(2-1)-C37--R58---R57-T1-TEL LINE

C159

{IC501(38)-R567-R573-C564-CN501(11)}-CN7(11)-R161-C119-IC5(77-63)-C53-R73-IC10(2-1)-C37--R58---R57T1-TEL LINE

{IC501(38)-R567-R573-C564-CN501(11)}-CN7(11)-R161-C119-IC5(77-41)-C100-R139-IC5(40-38)-C91R132-IC3(4-5,8)-SPEAKER

ROUTE

C159

J33-C56-C57-R80-R150-C113-IC5(59-45,56)

C159

FAX Rx ICM Rec

CNG / DTMF (OFF Hook) VO X DETECTION

FAX Rx

Greeting / MEMO Rec

Caller ID DTMF detection

(ON Hook)

Note:

{ }: digital board

TEL LINE-T1-R59-C44-IC10(6-7)-J33-C56-C59-R85-R89-C64-IC2(1-2)-C68CN7(9)-{CN501(9)-C701-IC801(3-4)-C943-J604-IC603-IC505(60)}

TEL LINE-T1-R59-C44-IC10(6-7)-J33-C56-C59-R85-R89-C64-IC2(1-2)-C68-CN7(9){CN501(9)-C701-IC801(3-4)-C943-J604-C603-IC505-(60)}

MIC-R110-C79-IC5(51-71)-C145-CN7(7)-{CN501(7)-R707-R913-C930-IC505(36)

TEL LINE-T2-C115-R154-IC5(61-67)-R167-C134-IC2(10-11)-C68-CN7(9)-{CN501(9)-C701-IC801(1-2)J606-C807-R808-IC803(6-7)-C948-IC801(11-10)-J604-C603-IC505(60)}

(Model KX-FP320E/KX-FM330E)

KX-FP320E/KX-FM330E

2.4.3. USER MODE (The list below is an example of the SYSTEM SETUP LIST the unit

prints out.) (Change from original page 103)

(KX-FM330 Only)

(Model KX-FP320E/KX-FM330E)

KX-FP320E/KX-FM330E

2.4.4. SERVICE FUNCTION TABLE (Change from original pages 104~105)

Code Function Set Value Effective Range Default Remarks

501 Pause time set X 100 ms. 001~600 035 - ------502 Flash time set X 10 ms. 01~99 8 -------503 Dial speed select 1:10 pps 2:20 pps 1, 2 1 -------520 CED f requency selec t 1:2100 Hz 2:1100 Hz 1, 2 1 See the Symptom/ Countermeasure

Table for long distance and inter national c alls in

Defe ctive facsim ile section.

521 International mode select 1:ON 2:OFF 1, 2 1 See the Symptom/ Countermeasure

Table for long distance and inter national c alls in

Defe ctive facsim ile section.

522 Auto standby select 1:ON 2:OFF 1, 2 1 The resolution reverts to the default

w hen trans mission is complete.

523 Receive equalizer select 1:0km 2:1.8km 3:3.6km

4:7.2km

524 Transmission egualizer select 1:0km 2:1.8km 3:3.6km

4:7.2km

533 Setting the number of times that

message transfer is redialed

534 Setting the message transf er /

pager call redial interv al Memory c lear: To reset the value to the def ault one, except the top margin (853) and

550 START input.

left margin (854) .

551 ROM chec k START input. 552 DTMF single tone test 1:ON 2:OFF 1, 2 2 See 553 Monitor on FAX communication

select

554 Modem test See 555 Scan check See 556 Motor test 0 See 557 LED test See 558 LCD test See 559 Document jam detection select 1:ON 2:OFF 1, 2 1 See 561 KEY test See 570 BREAK % select 1:61% 2:67% 1, 2 2 Sets the % break of pulse dialing

571 ITS auto redial time set X number of times 00~99 03 Selects the number of times that ITS is

572 ITS auto r edial line

disconnection time set

573 Remote turn-on ring number set X number of rings 01~99 20 Sets the number of rings before the

576 K Break detect 1:ON 2:OFF 1, 2 1 -------579 Detect bell type 1:TYPE 1 2:TYPE 2 1, 2 1 --- -- --580 TAM continuous tone detection 1:ON 2:OFF 1, 2 1 ON: STOP TAM operation w hen Dial

590 FAX auto redial time set X number of times 00~99 03 Selects the number of redial times

591 FAX auto redial time

disconnection time set

592 CNG transmit select 1:OFF

00~99 00~99 03 Selects the number of times that

001~999 sec 001~999 065 Sets the interval of message transf er /

1: OFF 2:PHASE B 3:ALL phas es

X sec ond 001~999 065 Sets the interv al of ITS redialing.

X second 001~999 065 Sets the FAX redial interval during

2:ALL 3:AUTO

1~4 1 When the telephone station is f ar f rom

the unit or reception cannot be perf ormed correc tly, adjust acc ordingly.

1~4 1 When the telephone station is f ar f rom

the unit or transmission cannot be perf ormed correc tly, adjust acc ordingly.

mess age trans f er is redialed (not including the firs t dialing).

pager call redial.

2. 5. T EST FUNC TI ONS.

1~3 1 --------

2. 5. T EST FUNC TI ONS.

2.2.1. Paper Jam.

2. 5. T EST FUNC TI ONS.

according PBX.

redialed (not including the first dial).

unit starts to rec eive a doc ument in the TEL mode.

tone, etc. are detected.

during FAX communication (not including the firs t dial).

FAX communication.

1~3 2 Lets you select the CNG output during

FAX transmission. ALL: CNG is output at phase A. AUTO: CNG is output only w hen automatic dialing is perf ormed. OFF: CNG is not output at phase A.

(Model KX-FP320E/KX-FM330E)

2.3.3.3.1.

+ 26 hidden pages