Operating Instructions
AC/Rechargeable hair clipper for professional use
Model No. ER1510
Before operating this unit, please read these instructions completely.
English 2
Deutsch 0
Français 00
Italiano 00
Nederlands 00
Español 00
Dansk 00
Português 00
Norsk 00
Svenska 00
Suomi 00
Polski 00
Česky 00
Slovensky 00
Magyar 00
Română 00
Русский 00
Türkçe 000
Українська 000
ER1510_EU.indb 1 2007/10/31 17:34:06
2
Important
Before use
This clipper is designed for professional use to trim hair and
beards. Charge it for 8 hours before use for the fist time in order to
activate the built‑in rechargeable batteries. It can be operated on
either an AC adaptor or rechargeable batteries. Read all
instructions carefully before use.
Charging the clipper
Use the ER1510 hair clipper with the RE5‑95 adaptor only.
Avoid charging the batteries at temperatures below 5 °C or
above 35 °C.
Avoid charging the batteries in direct sunlight or near a radiating
heat source.
The charge status ( ) lamp may blink at an early stage when
it is used for the first time or if it has not been used for 6 or more
months even if it is fully charged. This is not a malfunction.
Even though the clipper may not be used for an extended period,
charge every 6 months to preserve battery life.
The power cord cannot be replaced. If it is damaged, the AC
adaptor should be discarded.
Using the clipper
Warning ‑ Keep the appliance dry.
The clipper may become warm during operation and/or charging.
This is normal.
Check that the blades and the attachments are not damaged
before use. Replace them if they are damaged.
You should not allow permanent wave lotion, hair restorer or hair
spray to come into contact with the main body or the blades.
Doing so may result in cracking, discoloring or corrosion.
You should not drop the clipper on the floor.
You should not knock the blades and the attachments against
hard objects.
You should not trim the hair of a pet.
•
•
•
•
•
•
•
•
•
•
•
•
•
Cleaning the clipper
Clean the housing using only a cloth slightly dampened with
water or a mild soap solution.
Never use a caustic solution.
Never submerge the clipper in water.
Storing the clipper
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
Never tamper with moving parts.
Avoid grabbing the clipper by the power cord, as it may become
detached, causing damage or injury.
If the clipper is not working properly, have it inspected at an
authorized service center.
Specifications
Power source: 230 V AC, 50 Hz
Motor voltage: 2.4 V DC
Charging time: 1 hour
Airborne Acoustical Noise: 000 (dB (A) re 1 pW)
READ ALL INSTRUCTIONS BEFORE USE.
•
•
•
•
•
•
•
ER1510_EU.indb 2 2007/10/31 17:34:06
3
Parts identification
3
mm
0/0"
6
mm
0/0"
9
mm
0/0"
12
mm
0/0"
15
mm
0/0"
4
mm
0/0"
A Main body
1 Trimming height indicator
2 Dial (Height adjustment
control)
3 0·CHARGE/1 switch
4 Battery capacity lamp
5 Charge status ( ) lamp
6 Plug receptance
B Blade
7 Mounting hook
8 Cleaning lever
9 Moving blade
Stationary blade
C 3 mm comb attachment
D 4 mm comb attachment
E 6 mm comb attachment
F 9 mm comb attachment
G 12 mm comb attachment
H 15 mm comb attachment
I AC adaptor (RE5‑95)
; Power cord
Appliance plug
J Cleaning brush
K Oil
L Charging stand
Charging plug
Plug receptance
M Comb attachment shelves
(×2)
Charging the hair clipper
Charge
1
1
Connect the power
cord to the charging
stand.
2
2
Slide the 0·CHARGE/1
switch to “0·CHARGE”.
3
3
Place the clipper on
the charging stand and
plug in the adaptor
into a household
outlet.
Charge status ( ) lamp glows and charging starts.
Charging is completed when Charge status ( ) lamp
blinks. (Max. 1 hour later)
1 full charge will provide approximately 70 minutes of
continuous operation.
•
•
•
ER1510_EU.indb 3 2007/10/31 17:34:07
4
About the LED display
While charging
After charging is
completed
10 minutes after
charging is
completed
HIGH
MID
LOW
HIGH
MID
LOW
HIGH
MID
LOW
glows.
“HIGH”, “MID” or
“LOW” blinks.
•
blinks once
every second.
blinks once
every 2 seconds.
“HIGH/MID/LOW”
go out.
•
While using
HIGH
MID
LOW
“HIGH” blinks ‑ The battery capacity is enough.
“MID” blinks ‑ The battery capacity is approx.
60% or less.
“LOW” blinks ‑ The battery capacity is approx.
10% or less.
Charge the clipper when “LOW” starts to blink.•
Charging without the charging stand
1. Slide the 0·CHARGE/1 switch to “0·CHARGE”,
and insert the appliance plug into the clipper.
2. Plug in the adaptor into a household
outlet.
AC operation
If you connect the AC adaptor to the clipper in the same way as for
charging, and turn on the power, you can use it even if the battery
capacity is low.
If the clipper does not operate, charge the clipper for
approximately 1 minute.
Be careful not to discharge the battery completely with the power
left turned on. It results in shortening the battery life.
Using the hair clipper
Cut
Turn the dial clockwise or counterclockwise to adjust
the moving blade back and forth to get the desired
height. Adjustable in 5 stages from 0.8 mm to 2.0 mm
in 0.3 mm steps without attachments.
Using the comb attachments
1
1
Select the trimming heights
indicated on the insides and sides
of the attachments.
2
2
Set the dial to “0.8” and then
mount the attachment to the
clipper as illustrated.
0.8
•
•
ER1510_EU.indb 4 2007/10/31 17:34:07
5
Removing the attachment from the clipper
Remove the attachment as illustrated.
Blade maintenance
Care
Blade life
Blade life will vary according to the frequency and length of use. It
is expected to be about 3 months when used for 15 haircuts a day.
Removing and mounting the blade
Removing the blade
1. Hold the clipper with the switch
facing upward and push the
blade with your thumb while
catching the blade in your other
hand.
Be sure to turn off the power
before you remove the blade.
•
Mounting the blade
1. Set the dial to “2.0”.
2.0
2. Fit the mounting hook
into the blade mounting
on the clipper and push
in until it clicks.
Cleaning the blade
1. Brush off
any hairs
from the
clipper and
from around
the blade.
2. Remove the
blade and
brush off
the hairs
from the
blade edge.
3. Brush the hairs out from
between the stationary
blade and the moving
blade while pressing
down on the cleaning
lever to raise the moving
blade.
ER1510_EU.indb 5 2007/10/31 17:34:08
6
Lubrication
1. Apply a few drops of the oil to the space between the
stationary blade and moving blade.
Apply the oil to the clipper before and after each use.
2. Set the dial to “2.0” and then remount the blade on the
clipper.
•
Removing the built‑in rechargeable batteries
1. Remove the blades 1 and four screws 2.
2. Remove the spring 3, the under cover 4, and the blade holder
5.
3. Remove the dial 6 and open the housing 7, and then take out
two batteries 8.
Disconnect the clipper from a household outlet.
Fully discharge the batteries.
Be careful not to short‑circuit the batteries.
•
•
•
ER1510_EU.indb 6 2007/10/31 17:34:08
7
Information on Disposal for Users of Waste Electrical &
Electronic Equipment (private households)
This symbol on the products and/or
accompanying documents means that used
electrical and electronic products should not be
mixed with general household waste.
For proper treatment, recovery and recycling,
please take these products to designated
collection points, where they will be accepted on a
free of charge basis.
Alternatively, in some countries you may be able to return your
products to your local retailer upon the purchase of an
equivalent new product.
Disposing of this product correctly will help to save valuable
resources and prevent any potential negative effects on human
health and the environment which could otherwise arise from
inappropriate waste handling. Please contact your local authority
for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste,
in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please
contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the
European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local
authorities or dealer and ask for the correct method of disposal.
WARNING ‑ Do not attempt to replace the batteries for the
purpose of reusing the clipper. This could result in the risk of fire
or electric shock.
Important notice regarding environmental protection
The built‑in rechargeable Nickel‑Metal Hydride batteries contain
substances that may be environmentally harmful. Please remove
the batteries before discarding your clipper.
For environmental protection and recycling materials
This clipper contains Nickel‑Metal Hydride batteries.
Please make sure that the batteries are disposed of at an
officially assigned location, if there is one in your country.
ER1510_EU.indb 7 2007/10/31 17:34:08
No.1 EN, GE, FR, IT, DU, SP, DA, PT, NW, SW, FI, PL, CZ, SK, HU, RO, RU, TK, UA （欧州） Printed in Japan
Matsushita Electric Works, Ltd.
1048, Kadoma, Osaka 571‑8686, Japan
ER1510_EU.indb 8 2007/10/31 17:34:09
Loading...