Panasonic CQ-C1335L, CQ-C1305L User Manual

Download

WMA MP3 CD Player/Receiver

English

Model:

CQ-C1335U/CQ-C1305U

CQ-C1335L/CQ-C1305L

Operating Instructions

(CQ-C1335U)

• Please read these instructions (including “Limited Warranty” and “Customer Services Directory”) carefully before using this product and keep this manual for future reference.

Safety Information

Q Read the operating instructions for the unit and all other

components of your car audio system carefully before using the system. They contain instructions about how to use the system in a safe and effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this manual.

This pictograph intends to alert you to the presence of important operating instructions and installation

Warning

instructions. Failure to heed the instructions may result in severe injury or death.

Warning

Observe the following warnings when using this unit.

R The driver should neither watch the display nor operate

the system while driving.

Watching the display or operating the system will distract the driver from looking ahead of the vehicle and can cause accidents. Always stop the vehicle in a safe location and use the parking brake before watching the display or operating the system.

R Use the proper power supply.

This product is designed for operation with a negative grounded 12 V DC battery system. Never operate this product with other battery systems, especially a 24 V DC battery system.

R Keep batteries and insulation ﬁ lm out of reach of infants.

Batteries and insulation ﬁ lm can be ingested, so keep them out of the reach of infants. If an infant ingests a battery or insulation ﬁ lm, please seek immediate medical attention.

R Protect the Deck Mechanism.

Do not insert any foreign objects into the slot of this unit.

R Do not disassemble or modify the unit.

Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be repaired, consult your dealer or an authorized Panasonic Servicenter.

R Do not use the unit when it is out of order.

If the unit is out of order (no power, no sound) or in an abnormal state (has foreign objects in it, is exposed to water, is smoking, or smells), turn it off immediately and consult your dealer.

R The remote control unit should not lie about in the car.

If the remote control unit lies about, it could fall on the ﬂ oor while driving, get wedged under the brake pedal, and lead to a trafﬁ c accident.

R Refer fuse replacement to qualiﬁ ed service personnel.

When the fuse blows out, eliminate the cause and have it replaced with the fuse prescribed for this unit by a qualiﬁ ed service engineer. Incorrect replacement of the fuse may lead to smoke, ﬁ re, and damage to the product.

Q This manual uses pictographs to show you how to use the product

safely and to alert you to potential dangers resulting from improper connections and operations. The meanings of the pictographs are explained below. It is important that you fully understand the meanings of the pictographs in order to use this manual and the system properly.

This pictograph intends to alert you to the presence of important operating instructions and installation

Caution

instructions. Failure to heed the instructions may result in injury or material damage.

Observe the following warnings when installing.

R Disconnect the lead from the negative (–) battery

terminal before installation.

Wiring and installation with the negative (–) battery terminal connected may cause electrical shock and injury due to a short circuit. Some cars equipped with the electrical safety system have speciﬁ c procedures of battery terminal disconnection.

FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH.

R Never use safety-related components for installation,

grounding, and other such functions.

Do not use safety-related vehicle components (fuel tank, brake, suspension, steering wheel, pedals, airbag, etc.) for wiring or ﬁ xing the product or its accessories.

R Installing the product on the air bag cover or in a

location where it interferes with airbag operation is prohibited.

R Check for piping, gasoline tank, electric wiring, and

other items before installing the product.

If you need to open a hole in the vehicle chassis to attach or wire the product, ﬁ rst check where the wire harness, gasoline tank, and electric wiring are located. Then open the hole from outside if possible.

R Never install the product in a location where it interferes

with your ﬁ eld of vision.

R Never have the power cord branched to supply other

equipment with power.

R After installation and wiring, you should check the

normal operation of other electrical equipment.

The continuation of their using in abnormal conditions may cause ﬁ re, electrical shock or a trafﬁ c accident.

R In the case of installation to an airbag-equipping

car, conﬁ rm warnings and cautions of the vehicle manufacturer before installation.

R Make sure the leads do not interfere with driving or

getting in and out of the vehicle.

R Insulate all exposed wires to prevent short circuiting.

Caution

Observe the following cautions when using this unit.

R Keep the sound volume at an appropriate level.

Keep the volume level low enough to be aware of road and trafﬁ c conditions while driving.

R This unit is designed for use exclusively in automobiles. R Do not operate the unit for a prolonged period with the

engine turned off.

Operating the audio system for a long period of time with the engine turned off will drain the battery.

R Do not expose the unit to direct sunlight or excessive

heat.

Otherwise these will raise the interior temperature of the unit, and it may lead to smoke, ﬁ re, or other damage to the unit.

R Do not use the product where it is exposed to water,

moisture, or dust.

Exposure of the unit to water, moisture, or dust may lead to smoke, ﬁ re, or other damage to the unit. Make especially sure that the unit does not get wet in car washes or on rainy days.

R Set the volume level to low enough before the AUX

connection is completed.

Failure to observe this, the loud noise may come out and damage your speakers and your hearing. Direct connection of the speaker/ headphone output of an external device without any attenuator may distort sound or damage the connected external device.

Observe the following cautions when installing.

R Refer wiring and installation to qualiﬁ ed service

personnel.

Installation of this unit requires special skills and experience. For maximum safety, have it installed by your dealer. Panasonic is not liable for any problems resulting from your own installation of the unit.

R Follow the instructions to install and wire the product.

Not following the instructions to properly install and wire the product could cause an accident or ﬁ re.

R Take care not to damage the leads.

When wiring, take care not to damage the leads. Prevent them from getting caught in the vehicle chassis, screws, and moving parts such as seat rails. Do not scratch, pull, bend or twist the leads. Do not run them near heat sources or place heavy objects on them. If leads must be run over sharp metal edges, protect the leads by winding them with vinyl tape or similar protection.

R Use the designated parts and tools for installation.

Use the supplied or designated parts and appropriate tools to install the product. The use of parts other than those supplied or designated may result in internal damage to the unit. Faulty installation may lead to an accident, a malfunction or ﬁ re.

R Do not block the air vent or the cooling plate of the unit.

Blocking these parts will cause the interior of the unit to overheat and will result in ﬁ re or other damage.

R Do not install the product where it is exposed to strong

vibrations or is unstable.

Avoid slanted or strongly curved surfaces for installation. If the installation is not stable, the unit may fall down while driving and this can lead to an accident or injury.

R Installation Angle

The product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30˚. The user should bear in mind that in some areas there may be restrictions on how and where this unit must be installed. Consult your dealer for further details.

R Wear gloves for safety. Make sure that wiring is

completed before installation.

R To prevent damage to the unit, do not connect the power

connector until the whole wiring is completed.

R Do not connect more than one speaker to one set of

speaker leads. (except for connecting to a tweeter)

Observe the following cautions when handling the battery for the remote control unit.

• Use only speciﬁ ed battery (CR2025).

• Match the polarity of the battery with the (+) and (–) marks in the battery case.

• Replace a dead battery as soon as possible.

• Remove the battery from the remote control unit when not using it for an extended period of time.

• Insulate the battery (by placing them in a plastic bag or covering them with vinyl tape) before disposal or storage.

• Dispose of the battery according to the local regulations.

• Do not disassemble, recharge, heat or short the battery. Do not throw a battery into a ﬁ re or water.

In case of battery leakage

• Thoroughly wipe the battery liquid off the battery case and insert new battery.

• If any part of your body or clothing comes into contact with battery liquid, wash it with plenty of water.

• If battery liquid comes into contact with your eyes, wash them with plenty of water and get immediate medical attention.

CQ-C1335U

CQ-C1335L

Caution

THIS PRODUCT IS A CLASS I LASER PRODUCT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

The following applies only in the U.S.A.

Part 15 of the FCC Rules

FCC Warning:

Any unauthorized changes or modiﬁ cations to this equipment would void the user’s authority to operate this device.

Notice

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.

Before Reading These Instructions

Panasonic welcomes you to our constantly growing family of electronic products owners. We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.

This operating instruction manual is for 4 models CQ-C1335U, CQ-C1305U, CQ-C1335L and CQ-C1305L. All illustrations throughout this manual represent model CQ-C1335U unless otherwise speciﬁ ed. The following table describes the differences among 4 models.

Models

Features

Pre-Out Connector 2 (Front/Rear) 1 (Rear) 2 (Front/Rear) 1 (Rear) Remote Control Unit Supported

4 models

Differences among

Removable Face Plate Case

U.S.A.

Obtain Product Information and Operating Assistance; locate your nearest Dealer or Servicenter; purchase Parts and Accessories; or make Customer Service and Literature requests by visiting our Web Site at:

http://www.panasonic.com/support

or, contact us via the web at:

http://www.panasonic.com/contactinfo

You may also contact us directly at: 1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.

For hearing or speech impaired TTY users, TTY : 1-877-833-

Accessory Purchases:

Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:

http://www.pasc.panasonic.com

or, send your request by E-mail to:

npcparts@panasonic.com

You may also contact us directly at: 1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday-Friday 9 am to 8 pm, EST.) Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032

Customer Services Directory

(We accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)

For hearing or speech impaired TTY users, TTY : 1-866-605-

Service in Puerto Rico

Panasonic Puerto Rico, Inc. Panasonic Sales Company Factory Servicenter: Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Phone (787) 750-4300, Fax (787) 768-2910

CQ-C1335U CQ-C1305U CQ-C1335L CQ-C1305L

(Included)

Not Supported

Not Supported Not Supported

Supported (Included)

Not Supported

Supported (Included)

CANADA

WARRANTY SERVICE

FOR PRODUCT OPERATION ASSISTANCE, please contact:

Our Customer Care Centre:

Telephone #: (905) 624-5505 1-800 #: 1-800-561-5505 Fax #: (905) 238-2360 Email link: “Contact Us” on www.panasonic.ca

8855

1277

FOR PRODUCT REPAIRS, please locate your nearest Authorized Servicentre at www.panasonic.ca:

Link : “Servicentres™ locator” under “Customer support”

IF YOU SHIP THE PRODUCT TO A SERVICENTRE

Carefully pack and send prepaid, adequately insured and preferably in the original carton. Include details of the defect claimed, and proof of date of original purchase.

Limited Warranty

U.S.A.

PANASONIC CONSUMER ELECTRONICS COMPANY, DIVISION OF PANASONIC CORPORATION OF NORTH AMERICA One Panasonic Way, Secaucus, New Jersey 07094

PANASONIC SALES COMPANY, DIVISION OF PANASONIC PUERTO RICO, INC. Ave. 65 de infanteria, Km. 9.5, San Gabriel Industrial Park Carolina, Puerto Rico 00985

PANASONIC AUTO PRODUCTS LIMITED WARRANTY

LIMITED WARRANTY COVERAGE

If your product does not work properly because of defects in materials and workmanship. Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”) will, for the length of the period indicated in the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or refurbished product. The decision to repair or replace will be made by the warrantor.

Audio Components (except items listed below)

MXE Series Audio Components (except items listed below)

Speakers Defective Car Audio Speakers under warranty must be exchanged at the place of purchase. Contact your Dealer for details.

Accessories (in exchange for defective items)

During the “Labor” warranty period, there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. You must carry-in or mail-in your product prepaid during the warranty period. If nonrechargeable batteries are included, they are not warranted. This warranty only applies to products purchased and serviced in the United States or Puerto Rico. This warranty is extended only to the original purchaser of a new product which was not sold “as is”. A purchase receipt or other proof of the original purchase date is required for warranty service.

CARRY-IN OR MAIL-IN SERVICE

For Carry-In or Mail-In Service in the United States, call 1-800-211-PANA (7262) or visit Panasonic Web Site: http://www.panasonic.com For assistance in Puerto Rico, call Panasonic Sales Company (787)-7504300 or fax (787)-768-2910.

LIMITED WARRANTY LIMITS AND EXCLUSIONS

This warranty ONLY COVERS failures due to defects in materials and workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred during shipment, failures which are caused by products not supplied by the warrantor, failures which result from accident, misuse, abuse, neglect, bug infestation, mishandling, misapplication, alteration, faulty installation, set-up adjustment, maladjustment of consumer control, improper maintenance, improper antenna, inadequate signal reception or pickup, power line surge, improper voltage supply, lightning, modiﬁ cation, commercial use (such as use in hotels, ofﬁ ces, restaurants, or other business uses) or rental use of the product, or service by anyone other than the technician from Factory Servicenter or other authorized service centers, or damage that is attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost

time, cost of having someone remove or re-install an installed unit if applicable, travel to and from the sevicer, and loss of media, data or other memory contents. The items listed are not exclusive, but are for illustration only.) ALL EXPRESS AND IMPLIED WARRANTIES,

INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

Categories Parts Labor

One (1) Year One (1) Year

Two (2) Years Two (2) Years

One (1) Year Not Applicable

Ninety (90) Days Not Applicable

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.

This warranty gives you speciﬁ c legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to warrantor’s Consumer Affairs Department at the addresses of the warrantor.

PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY.

Customer’s Record Model No. Serial No. Dealer’s No. Code No. Dealer’s Address Date of Purchase

CANADA

Panasonic Canada Inc. 5770 Ambler Drive, Mississauga Ontario L4W 2T3

PANASONIC PRODUCT LIMITED WARRANTY

Panasonic Canada Inc. warrants this product to be free from defects in materials and workmanship and agrees to remedy any such defect for a period as stated below from the date of original purchase.

CAR AUDIO PRODUCT – ONE (1) YEAR, PARTS AND LABOUR

(The labour to install or remove the product is not warranted) ACCESSORIES - NINETY (90) DAYS, (IN EXCHANGE FOR DEFECTIVE ITEMS)

LIMITATIONS AND EXCLUSIONS

This warranty does not apply to products purchased outside Canada or to any product which has been improperly installed, subjected to usage for which the product was not designed, misused or abused, damaged during shipping, or which has been altered or repaired in any way that affects the reliability or detracts from the performance, nor does it cover any product which is used commercially. Dry cell batteries are also excluded from coverage under this warranty. This warranty is extended to the original end user purchaser only. A purchase receipt or other proof of the original purchase date is required before warranty service is performed.

THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.

In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable.

Accessories

Instruction kit

Operating Instructions

(English: YEFM285905) (Français: YEFM285906) (Español: YEFM285907)

Installation Instructions

(YEFM294287)

Owners Information Card

Instruction kit

Operating Instructions

(English: YEFM285905) (Español: YEFM285907)

Installation Instructions

(YEFM294287)

CQ-C1335U CQ-C1305U

Q’ty: 1 set

Q’ty: 1

CQ-C1335L CQ-C1305L

Q’ty: 1 set

Q’ty: 1

Installation kit (YEP0FZ5698)

Lock Cancel Plate

Mounting Bolt (5 mm )

Rubber Bushing

Q’ty: 1

Mounting Collar

(YEFX0217263A)

Q’ty: 1

Trim Plate

(YEFC051020)

Q’ty: 1

Power Connector

(YGAJ021012)

Q’ty: 1

CQ-C1335U CQ-C1335L

Remote Control Unit (includes a battery)

(EUR7641010) Q’ty: 1

CQ-C1335L CQ-C1305L

Removable Face Plate Case

(YEFA131839A)

Q’ty: 1

Notes:

• The number in parentheses underneath each accessory part name is the part number for maintenance and service.

• Accessories and their part numbers are subject to modiﬁ cation without prior notice due to improvements.

• Mounting Collar and Trim Plate are mounted on the main unit at shipment.

CQ-C1335U CQ-C1305U

Request for use of the Removable Face Plate Case:

• To avoid trouble and ensure safety, use the optional Removable Face Plate Case (YEFA131839A).

Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America

One Panasonic Way, Secaucus, New Jersey 07094 http://www.panasonic.com

Panasonic Sales Company, Division of Panasonic Puerto Rico, Inc. (“PSC”)

Ave. 65 de Infanteria, Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 http://www.panasonic.com

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3 http://www.panasonic.ca

Matsushita Electric Industrial Co., Ltd.

Web Site: http://panasonic.net

YEFM285905A FT1006-1116 Printed in China

Preparation

Set your car’s ignition switch to the ACC or

ON position.

C A

N O

Press [SOURCE] (PWR: Power).

First Time Power OnBattery InstallationClock Setting

CQ-C1335U CQ-C1335L

Pull the insulation ﬁ lm out from the backside of the remote control gently.

The 12-hour system is used for the clock.

Press [DISP].

(clock display)

Hold down [DISP] for more than 2 seconds.

Hour blinks

Adjust the hour.

Hour entered

Note: Battery Information: Battery Type: Panasonic lithium battery (CR2025) (Included in

the remote control)

Battery Life: Approximately 6 months under normal use (at

room temperature)

Press [DISP].

Completed

Notes:

• “ADJUST” is displayed before adjusting the clock.

• Hold down [] or [] to change numbers rapidly.

Clock Display at Power Off

Press [DISP] to change the display.

Display off

[]: sets the hour ahead. []: sets the hour back.

Press [DISP].

Adjust the minute.

[]: sets the minute ahead. []: sets the minute back.

Clock display

Minute blinks

Minute entered

Maintenance/Fuse

Your product is designed and manufactured to ensure the minimum of maintenance. Use a dry, soft cloth for routine exterior cleaning. Never use benzine, thinner, or other solvents.

Unit

Cleaning the

If the fuse blows out, consult your dealer, or your nearest authorized Panasonic Servicenter.

Warning

Fuse

• Use fuses of the same speciﬁ ed rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit directly without a fuse could cause ﬁ re or damage to the unit. If the replaced fuse fails, contact your nearest authorized

Panasonic Servicenter.

Anti-Theft System

This unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.

Caution

• This face plate is not waterproof. Do not expose it to water

or excessive moisture.

• Do not remove the face plate while driving your car.

• Do not place the face plate on the dashboard or nearby

areas where the temperature rises high.

Removing

Turn off the power.

Press []. The face plate will open.

Pull it out toward you.

(Anti-Theft System)

Face Plate Removing/Mounting



• Do not touch the contacts on the face plate and the main unit, since this may result in poor electrical contact.

• If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth.

Mounting

Slide the left side of the face plate in place.

Press the right end of face plate until a

“click” is heard.

[]





Notes on Discs

If you use commercial CDs, they must have either of these labels shown at right. Some copy-protected music CDs are not playable.

How to hold the disc

• Do not touch the underside of the disc.

• Do not scratch on the disc.

• Do not bend the disc.

• When not in use, keep disc in the case.

Do not leave discs in the following places:

• In direct sunlight

• Near car heaters

• Dirty, dusty and damp areas

• On seats and dashboards

Disc cleaning

Use a dry, soft cloth to wipe from the center outward.

otes on CD/CD Media N

(CD-ROM, CD-R, CD-RW)

Do not write on the disc label with a ballpoint pen or other hard-point pens.

• You may have trouble playing back some CD-R/RW discs recorded using CD recorders (CD-R/RW drives), either due to their recording characteristics or dirt, ﬁ ngerprints, scratches, etc. on the disc surface.

• CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving them inside a car for extended periods may damage and make playback impossible.

• Some CD-R/RWs cannot be played back successfully due to incompatibility among writing software, a CD recorder (CDR/RW drive) and the discs.

• This player cannot play the CD-R/RW discs if the session is not closed.

• This player cannot play the CD-R/RW discs which contain other than CD-DA or MP3/WMA data (Video CD, etc.).

• Be sure to observe the instructions of the CD-R/RW disc for handling it.

<Wrong>

Printed side

Labels created by a printer, Protective ﬁ lms or sheets

Disc with adhered stickers or tape

• You may encounter trouble in playing MP3/WMA ﬁ les or displaying the information of MP3/WMA ﬁ les recorded with certain writing software or CD recorders.

• The ﬁ le extension “.mp3” or “.wma” should be assigned to each ﬁ le depending on the ﬁ le format.

• This unit does not have the play list function.

• Although Multi-session recording is supported, the use of Disc-at-Once is recommended.

Irregularly shaped discs

Discs with cracks, scratches or parts missing

Supported ﬁ le systems

ISO 9660 Level 1/Level 2, Apple Extension to ISO 9660, Joliet, Romeo

Note: Apple HFS, UDF 1.50, MIX mode CD, CD Extra is not supported.

Compression formats

(Recommendation: “Points to remember when making MP3/WMA ﬁ les” on the right.)

Recording MP3/WMA ﬁ les on a CD-media

• You are recommended to minimize the chances of making a disc that contains both CD-DA ﬁ les and MP3/WMA ﬁ les.

Notes on CD-Rs/RWs

• If CD-DA ﬁ les are on the same disc as MP3 or WMA ﬁ les, the songs may not play in the intended order, or some songs may not play at all.

• When storing MP3 data and WMA data on the same disc, use different folders for each data.

• Do not record ﬁ les other than MP3/WMA ﬁ les and unnecessary folder on a disc.

• The name of MP3/WMA ﬁ le should be added by rules as shown in the following descriptions and also comply with the rules of each ﬁ le system.

• MPEG 1 audio layer 3 Bit rate: 32 k–320 kbps VBR: Yes Sampling frequency: 32, 44.1, 48 kHz

• Windows Media Audio Ver. 7, 8, 9* Bit rate: 32 k–192 kbps VBR: Yes Sampling frequency: 32, 44.1, 48 kHz

* WMA 9 Professional/LossLess/Voice are not supported.

• MPEG 2 audio layer 3 Bit rate: 8 k–160 kbps VBR: Yes Sampling frequency: 16, 22.05, 24 kHz

Notes on MP3/WMA

Note: MP3/WMA encoding and writing software is not supplied with this unit.

Points to remember when making MP3/WMA ﬁ les

Common

• High bit rate and high sampling frequency are recommended for high quality sounds.

• Selecting VBR (Variable Bit Rate) is not recommended because playing time is not displayed properly and sound may be skipped.

• The playback sound quality differs depending on the encoding circumstances. For details, refer to the user manual of your own encoding software and writing software.

MP3*

• It is recommended to set the bit rate to “128 kbps or more” and “ﬁ xed”.

* MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

WMA

• It is recommended to set the bit rate to “64 kbps or more” and “ﬁ xed”.

• Do not set the copy protect attribute on the WMA ﬁ le to enable this unit to play back.

Caution

• Never assign the “.mp3”, or “.wma” ﬁ le name extension to a ﬁ le that is not in the MP3/WMA format. This may not only produce noise from the speaker damage, but also damage your hearing.

Display Information

Displayed items

Notes on MP3/WMA

• CD-TEXT • MP3 (ID3 tag)

Disc title Album name Track title Title name/Artist name

• MP3/WMA • WMA (WMA tag) Folder name Album name File name Title name/Artist name

Displayable characters

• Displayable length of file name/folder name: within 32 characters. (Unicoded file and folder names are reduced by half in the number of displayable characters.)

• Name ﬁ les and folders in accordance with the standard of each ﬁ le system. Refer to the instructions of writing software for details.

• ASCII character set and special characters in each language can be displayed.

Notes:

• With some software in which MP3/WMA format files have been encoded, the character information may not be displayed properly.

• Undisplayable characters and symbols will be converted into an asterisk (

Folder selection order/ﬁ le playback order

Root folder (Root Directory)

Tree 1 Tree 2 Tree 3 Tree 4 ......................... Tree 8

Maximum number of ﬁ les/folders

• Maximum number of ﬁ les: 999

• Maximum number of ﬁ les in one folder: 255

• Maximum depth of trees: 8 Maximum number of folders: 255 (Root folder is included.)

•

Notes:

• This unit counts the number of folders irrespective of the presence or absence of MP3/WMA ﬁ le. If the selected folder does not contain any MP3/WMA ﬁ les, the

• nearest MP3/WMA ﬁ les in the order of playback will be played.

• Playback order may be different from other MP3/WMA players even if the same disc is used.

• “ROOT” appears when displaying the root folder name.

Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries/regions.

Folder Selection

In the order

File Selection

In the order

(Max.)

It is prohibited by copyright laws to copy, distribute and deliver copyrighted materials such as music without the approval of copyright holder except enjoying yourself personally.

No warranty

Above description complies with our investigations as of September 2006. It has no warranty for reproducibility and displayability of MP3/WMA.

Remote Control Unit

CQ-C1335U CQ-C1335L

Notes:

• This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)

• Aim the remote control at the remote sensor and operate it.

[0] to [9]

selects a preset station (1 to 6), presets the current station (Hold it down for more than 2 seconds.), inputs the number in direct selection.

[#] (NUMBER)

executes the direct selection.

[RANDOM] [SCAN] [REPEAT]

toggles on/off each play mode.

[] []

down/up the frequency (Hold it down for more than

0.5 seconds and release it for seek tuning. [] []

skip to the previous/next folder in player mode.

[] []

skip to the previous/next track/ﬁ le in player mode. Hold it down for fast reverse/fast forward.

[BAND]

selects a band in the tuner source, toggles pause/play in player source, executes the APM (Auto Preset Memory) in tuner source (Hold it down for more than 2 seconds).

[SRC] (SOURCE)

selects a source.

(POWER)

toggles power on/off.

[MENU] (SEL: Select) selects the items in the audio menu.

[VOL] (volume) adjusts the volume, and selects the value in the audio menu, etc.

[MUTE]

toggles mute on/off.

[DISP] (Display) switches the information on display, and exits the audio menu.

Direct Access

A track (CD mode), ﬁ le, folder (MP3/WMA mode) can be directly selected.

Example: Track number 5

1 2 3

Notes:

• To suspend direct selection, press [DISP].

• For folder selection, enter a number after pressing [#] (NUMBER) twice.

Functions only on Main unit

The following functions are not available on remote control unit.

Functions

• SQ selection • Scroll • Disc eject

Battery Replacement



Press [#] (NUMBER).

Press [5].

Press [BAND] (SET).

Remove the battery holder with the remote control unit placed on a ﬂ at surface.

 Stick your thumbnail

into the groove, and push the holder in the direction of the arrow, and at the same time.

 Pull it out in the

direction of the arrow using a tough pointed object.

Tough pointed object

Back side

 Put a battery in the case with (+) side facing up.  Put the case back.





Warning

• Keep batteries away from children to avoid the risk of accidents. If an infant ingests a battery, please seek immediate medical attention.

Caution

• Remove and dispose of an old battery immediately.

• Do not disassemble, heat or short a battery. Do not throw a battery into a ﬁ re or water.

• Follow local regulations when disposing of a battery.

• Improper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a ﬁ re.

Notice

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.

Notes: Battery Information: Battery Type: Panasonic lithium battery (CR2025) (Included

in the remote control)

Battery Life: Approximately 6 months under normal use (at

room temperature)

General

selects a source. [PWR] (Power) toggles power on/off.

[VOL] (Volume)[SOURCE] (Source)

[SQ] (Sound Quality)

selects a sound type (SQ).

[MUTE]

toggles mute on/off.

Power On/Off

Set your car’s ignition switch to the ACC or ON position.

Power on: Press [SOURCE] (PWR). Power off: Hold down [SOURCE] (PWR) for

Source Selection

Press [SOURCE] to change the source.

Volume Adjustment

(Setting Range: 0 to 40, Default: 18) Turn [VOL].

Remote Control Sensor

• Set the volume level to low

enough before the AUX connection is completed.

Failure to observe this, the

loud noise may come out and damage your speakers and your hearing.

more than 1 second.

Radio Disc Player AUX IN

Caution

*[AUX] (AUX IN)

From line output of external sound/audio device (ex. Silicon-audio player, HDD player, etc.)

*AUX IN:

(3.5 mm  stereo)

SQ (Sound Quality)

SQ is a function that can call up various sound types at the touch of button in accordance with your listening music type.

Press [SQ] to select the sound type (SQ) as follows:

(FLAT) ﬂ at frequency response: does not emphasize any part. (Default)

(ROCK) speedy and heavy sound: exaggerates bass and treble.

(POP) wide-ranged and deep sound: slightly emphasizes bass and treble.

Mute

ON: Press [MUTE]. ( lights.)

General Operations

OFF: Press [MUTE] again.

(VOCAL) clear sound: emphasizes middle tone and slightly emphasizes treble.

Notes:

• If no operation takes place for more than 5 seconds in

SQ selection mode, the display returns to the regular mode.

•

Settings of SQ, bass and treble are inﬂ uenced one another. If such an inﬂ uence causes distortion to the audio readjust bass/treble or volume.

• For further information on Bass, Treble, Balance and Fader

settings, refer to Audio Settings.

the

signal,

Radio (AM/FM)

[SOURCE] (Source) selects a source.

[DISP] (Display) switches the information on the display.

[BAND]

selects a band in the radio source. [APM] (Auto Preset Memory) executes APM in the radio source. (Hold it down for more than 2 seconds.)

[TUNE ] [TUNE ] down/up the frequency. (Hold it down for more than 0.5 seconds and release it for seek tuning.)

Preset buttons [1] to [6] selects a preset station in the radio source, and presets the current station. (Hold it down for more than 2 seconds.)

Press [SOURCE] to select the radio source.

Press [BAND] to select a band.

Operation Flow

Select a station.

Frequency adjustment

[TUNE ]: Lower [TUNE ]: Higher

Note: Hold down for 0.5 sec. or more and release for station

search.

Preset station selection

Press the corresponding preset button from [1] to [6] to tune in a preset station.

Band Frequency Preset Number

Radio Source DisplayStation Preset

Display change

Press [DISP] to change the display.

Radio mode display (Default)

lights while receiving an FM stereo signal.

Clock display

Up to 6 stations can be preset in AM, FM1, FM2, and FM3 respectively. Preset stations can be simply called up by pressing [1] to [6].

Auto Preset Memory (APM)

With this operation, stations with good receiving conditions can be automatically stored in the preset memory.

Select a band.

Hold down [BAND] (APM) for more than

2 seconds.

The preset stations under best receiving conditions are received for 5 seconds each after presetting the stations (SCAN). To stop scanning, press one of the buttons from

[1] to [6].

Note: New stations overwrite existing saved stations.

Manual station preset

1 2

Note: New stations overwrite existing saved stations.

Tune into a station.

Hold down one of the preset buttons from

[1] to [6] for more than 2 seconds.

(blinks once)

Audio Settings

[VOL]

selects a value in the audio menu. (PUSH SEL) (Push to select) selects items in the audio menu.

[DISP] (Display) exits from the audio menu.

Press [VOL] (PUSH SEL) to display the audio menu display.

Note: If no operation takes place for more than 5 seconds in the audio menu (2 seconds in Main volume adjustment),

the display returns to the regular mode.

Press [VOL] (PUSH SEL) to select a

mode to be adjusted.

(Setting Range: 0 to 40, Default: 18)

(Setting Range: –12 dB to +12 dB by 2 dB, Default: 0 dB)

Audio menu

(Setting Range: 15 levels each, Default CNT (center))

Volume

Bass

Treble

Balance

Fader

Tur n [VOL] clockwise or counterclockwise

to adjust.

: Up : Down

: Increased : Decreased

: Right enhanced : Left enhanced

(Setting Range: 15 levels each, Default CNT (center))

Notes:

• If the fader is set to front, the pre-amp. output (rear) is decreased.

•

For further information on SQ (Sound Quality) settings, refer to General.

• Settings of SQ, bass and treble are inﬂ uenced one another. If such an inﬂ uence causes distortion to the audio signal, readjust bass/treble or volume.

: Front enhanced : Rear enhanced

Player (Disc Player)

Disc slot

takes a disc in with the printed side facing up.

Notes:

• The power will be turned on automatically when a disc is loaded.

• A disc which has both CD-DA data and MP3/WMA data on it may not be reproduced normally.

[SOURCE] (Source) selects a source.

() (Play/Pause) toggles pause/play in the player source.

Printed side up

[] (Eject) ejects the disc.

[DISP] (Display) switches the information on the display.

[] []

skip to the previous/next track/ﬁ le in the player mode. Hold down either of them for fast reverse/fast forward.

Caution

• Do not insert a disc when the indicator lights.

• Refer to the section of “Notes on Discs” and “Notes on MP3/

WMA”.

• This unit does not support 8 cm {3\} discs.

• If you insert an 8 cm {3S} disc and cannot eject it, turn ACC of your car off once and turn it on again, then press [] (Eject).

Press [SOURCE] to select the Disc Player

source.

Select a desired portion.

Track/ﬁ le selection

Press [] / [].

Note: To perform fast forward/reverse, hold down either of

them.

Disc Player (CD-DA disc):

Previous/next track

Operation Flow

Disc Player (MP3/WMA disc):

Previous/next ﬁ le

[] []

skip to the previous/ next folder.

• Do not insert foreign matter into the disc slot.

[4] (RANDOM)/[5] (SCAN)/[6] (REPEAT)

toggles on/off each play mode.

[3] (SCROLL)

scrolls the information on display.

Pause

Press [BAND] (). Press again to cancel.

Folder selection (MP3/WMA)

Press [] / [].

CD-DA mode display

Track number Play time

Display change

Press [DISP] to change the display.

Disc Player (CD-DA disc):

Normal

Disc Player (MP3/WMA disc):

Normal

Lights when the disc is loaded.

MP3/WMA mode display

Folder number

lights when folder random/ repeat/scan is on.

Player Source DisplayRandom, Repeat, Scan

Random play

All the available songs (tracks/ﬁ les) are played in a random sequence.

Press [4] (RANDOM). Press again to cancel.

File number

Play Mode indicators

Disc title

Track title

Clock

Play time

Folder name/ Album*

File name/ Title, artist*

Clock

*ID3/WMA Tag On/Off

Hold down [3] for more than 2 seconds.

album title and song title/ artist name are displayed.

(Default)

folder name/ﬁ le name are displayed.

Notes:

• For scrolling text, press [3] (SCROLL).

• “NO TEXT” is displayed when there is no information on the disc.

Folder repeat play (MP3/WMA)

The current folder is repeated.

Hold down [6] (REPEAT) for more than 2 seconds. Hold down again to cancel.

Folder random play (MP3/WMA)

All the available ﬁ les in current folder are played in a random sequence.

Hold down [4] (RANDOM) for more than 2 seconds. Hold down again to cancel.

Repeat play

The current song (track/ﬁ le) is repeated.

Press [6] (REPEAT). Press again to cancel.

Scan play

The ﬁ rst 10 seconds of each songs (tracks/ﬁ les) is played in sequence.

Press [5] (SCAN). Press again to cancel.

Folder scan play (MP3/WMA)

From the next folder, the ﬁ rst 10 seconds of the ﬁ rst ﬁ le in each folder is played in sequence.

Hold down [5] (SCAN) for more than 2 seconds. Hold down again to cancel.

Troubleshooting

If You Suspect Something Wrong

Check and take steps as described below. If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic Servicenter. The product should be serviced only by qualiﬁ ed personnel. Please refer the checking and the repair to professionals. Panasonic shall not be liable for any accidents arising out of neglect of checking the unit or your own repair after your checking.

Never take measures especially those other than indicated by italic letters in “Possible Solution” described below because those are too dangerous for users to handle themselves.

Trouble Possible Solution

Common

• Start the engine. (Or turn the ignition

switch to the ACC position.)

• Verify the wiring. (battery lead, power

No power

No sound

Noise

No sound from

left, right, front,

or rear speaker

Left and right

sounds are

reversed

lead, ground lead, etc.)

•

Fuse blown (Contact the nearest Panasonic Servicenter.)

• Ask a professional for fuse replacement.

• Be sure to use the same rated fuse.

• Disable the mute function.

• Verify the wiring.

• Wait until the dew disappears before

turning on the unit.

• Make sure that grounding is established

properly.

• Adjust the balance and fader.

• Verify the wiring.

• Connect the speaker lead correctly.

Warning

• Do not use the unit in an irregular condition, for example, without sound, or with smoke or a foul smell, which can cause ignition or electric shock. Immediately stop using the unit and consult your dealer.

• Never try to repair the unit by yourself because it is dangerous to do so.

Trouble Possible Solution

Radio

• Tune in to another station of high-intensity

Frequent noise

Preset data

deleted

Error Display Messages

waves.

• Make sure that the antenna mounted point

is grounded properly.

• The preset memory is cleared to return to

the original factory setting when the power connector or battery is disconnected.

(The disc is ejected automatically.) The disc is dirty or upside down.

• Check the disc.

(The disc is ejected automatically.) The disc has scratches.

• Check the disc.

No operation by some cause.

• If normal operation is not restored, consult

your dealer or the nearest Servicenter to ask for repairs.

Cannot read the ﬁ le

• Check the disc.

Disc Player

No sound,

or disc is

automatically

ejected

Sound skip,

poor sound

quality

Sound skip due

to vibration

Disc not

ejectable

• Load the disc correctly.

• Clean the disc.

• The maximum permissible tilt angle is

30°.

• Secure the unit.

• Press []. If the disc is still not

ejected, contact the nearest Panasonic Servicenter.

A WMA ﬁ le can be copyrighted.

• The ﬁ le protected by copyright is not

playable.

Speciﬁ cations

General

Power supply : DC 12 V (11 V – 16 V DC), test voltage

14.4 V, negative ground Current consumption : Less than 2.1 A (CD mode; 0.5 W x 4 channels) Maximum power output : 50 W x 4 channels (at 1 kHz), volume

control maximum Tone adjustment range : Bass: ±12 dB at 100 Hz, Treble: ±12 dB at 10 kHz Speaker impedance : 4 – 8 j Pre-amp output voltage : 2.5 V (CD mode, 1 kHz, 0 dB) Pre-amp output impedance : 200 j Dimensions (W x H x D) : 178 x 50 x 160 mm {7\ x 1 15/16\ x 6 2/16\} Weight : 1.3 kg {2 lbs. 14 oz} Front AUX input Input impedance : 10 kj Allowable external input : 2.0 V Connector : 3.5 mm  Stereo mini-pin

Disc Player

Sampling frequency : 8 times oversampling DA converter : 1 bit DAC System Pick-up type : Astigma 3-beam Light source : Semiconductor laser Wave length : 790 nm Frequency response : 20 Hz – 20 kHz (±1 dB) Signal to noise ratio : 96 dB Total harmonic distortion : 0.01 % (1 kHz) Wow and ﬂ utter : Below measurable limits Channel separation : 75 dB

FM Stereo Radio

Frequency range : 87.9 MHz – 107.9 MHz Usable sensitivity : 10.2 dBf. (0.9 μV, 75 j) 50 dB quieting sensitivity : 15.2 dBf. (1.6 μV, 75 j) Frequency response : 30 Hz – 15 kHz (±3 dB) Alternate channel selectivity : 75 dB Stereo separation : 35 dB (1 kHz) Image rejection ratio : 55 dB IF rejection ratio : 100 dB Signal/noise ratio : 62 dB

AM Radio

Frequency range : 530 kHz – 1 710 kHz Usable sensitivity : 27 dB/μV (22

Above speciﬁ cations comply with EIA standards.

Power Output: 18 W RMS x 4 Channels at 4 j and 1% THD+N Signal to Noise Ratio: 85 dBA (reference: 1 W into 4 j)

Notes:

• Speciﬁ cations and design are subject to modiﬁ cation without notice due to improvements.

• Some ﬁ gures and illustrations in this manual may be different from your product.

μV, S/N 20 dB)

Memorandum

EnglishFrançaisEspañol

Installation Instructions

Instructions d’installation

Instrucciones de instalación

WMA MP3 CD Player/Receiver

Reproductor de CD, WMA y MP3/receptor

Récepteur/lecteur CD avec lecture WMA/MP3

Model: CQ-C1335U/C1305U

Lock Cancel Plate

Plaque antiblocage

Placa de cancelación de bloqueo

Installation Instructions

Instructions d’installation

Instrucciones de instalación



CQ-C1335L/C1305L

YEFX0217263A

Mounting Bolt (5 mm )

Boulon de ﬁ xation (5 mm )

Perno de montaje (5 mm )



Rubber Bushing

Bague en caoutchouc

Buje de goma



YGAJ021012

consist of a set. (YEP0FZ5698)

forman un juego. (YEP0FZ5698)



constituent un jeu. (YEP0FZ5698)



and





YEFC051020

L4W 2T3

http://www.panasonic.ca

Ave. 65 de Infanteria, Km. 9.5

San Gabriel Industrial Park,

Carolina, Puerto Rico 00985

http://www.panasonic.com

YEFM294287 FT1006-0 Printed in China

Panasonic Canada Inc.

5770 Ambler Drive,

Mississauga, Ontario

Panasonic Sales Company,

Division of Panasonic Puerto

Rico, Inc. (“PSC”)

Impreso en China

Imprimé en Chine

(CQ-C1335U)

TEXT

Supplied Hardware/Matériel d’installation/Accesorios suministrados

Panasonic Consumer

Electronics Company,

Division of Panasonic

Corporation of North America

One Panasonic Way, Secaucus,

New Jersey 07094

http://www.panasonic.com

Power Connector

Connecteur d’alimentation

Conector de alimentación

Trim Plate

Plaque de garniture

Mounting Collar

Cadre de montage

Collar de montaje

Please refer to the “WARNING” statement above.

Exclusively operated with 12 V battery with negative (–) ground.

Connect the power lead (red) very last.



Connect the battery lead (yellow) to the positive (+) terminal

of the battery or fuse block terminal (BAT).



• Please read these instructions carefully before using this product and keep this manual for future reference.

• Prière de lire ces instructions attentivement avant d’utiliser le produit et garder ce manuel pour l’utilisation ultérieure.

No. Item Diagram Q’ty No. Item Diagram Q’ty

• Lea con atención estas instrucciones antes de utilizar el producto y guarde este manual para poderlo consultar en el futuro.

Before Wiring/Avant le câblage/

Antes de realizar las conexiones

Placa de guarnición



Strip about 5 mm {1/4”} of the lead ends for connection.

Apply insulating tape to bare leads.

Reportez-vous à l’ “AVERTISSEMENT” ci-dessus.

Alimentez l’appareil exclusivement par la batterie de 12 V

Los números que aparecen entre paréntesis debajo del nombre de cada accesorio son los números de pieza para ﬁ nes de mantenimiento y servicio técnico.

• Los accesorios y sus números de pieza están sujetos a modiﬁ caciones sin previo aviso por razones de mejora del producto.

Notes:

• The number in parentheses underneath each accessory part name is the part number for maintenance and service.

• Accessories and their part numbers are subject to modiﬁ cation without prior notice due to improvements.

• Mounting Collar and Trim Plate are mounted on the main unit at shipment.

Remarques:

• Le nombre entre parenthèses au-dessous du nom de chaque accessoire représente la référence de la pièce pour l’entretien et la réparation.

• Les accessoires et leurs références sont sujets à changement sans préavis en vue de l’amélioration.

avec sa polarité négative (–) mise à la masse.

Raccordez le ﬁ l d’alimentation (rouge) en dernier.

Connectez le ﬁ l (jaune) à la borne positive (+) de la batterie

ou à la borne (BAT) de la boîte à fusibles.

Dénudez les extrémités de ﬁ l de 5 mm {1/4 po} environ pour

la connexion.

Recouvrez les ﬁ ls nus d’un ruban isolant.

• El collar de montaje y la placa de guarnición se montan en la unidad principal al salir de fábrica.

• Le cadre de montage et la plaque de garniture sont montés sur l’appareil principal lors de l’expédition.

Notas:

•

Consulte el apartado “ADVERTENCIA” arriba mencionado.

Conecte exclusivamente una alimentación de batería de 12 V

con el negativo (–) a tierra.

Conecte el cable de la alimentación (rojo) en último lugar.

Conecte el cable de la batería (amarillo) al terminal positivo

(+) de la batería o al terminal (BAT) del bloque de fusibles.

Pele unos 5 mm {1/4”} de los extremos

del cable para efectuar la conexión.

Ponga cinta aislante en los cables

Matsushita Electric Industrial Co., Ltd.

Web Site : http://panasonic.net

desnudos.

WARNING/AVERTISSEMENT/ADVERTENCIA

This installation information is designed for professional installers with knowledge of automobile electrical safety systems and is not intended

S

for non-technical, do-it-yourself individuals. It does not contain instructions on the electrical installation and avoidance of potential harm to air

bag, anti-theft and ABS braking or other systems necessary to install this product. Any attempt to install this product in a motor vehicle by anyone

If your car is equipped with air bag and/or anti-theft systems, speciﬁ c procedures may be required for connection and disconnection of

the battery to install this product. Before attempting installation of this electronic component against the manufacturer’s recommendation,

you must contact your car dealer or manufacturer to determine the required procedure and strictly follow their instructions.

S

FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOYMENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT

other than a professional installer could cause damage to the electrical safety system and could result in serious personal injury or death.

SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH.

SLes informations concernant cette installation sont destinées aux techniciens professionnels, compétents dans le domaine des

systèmes de sécurité électrique pour automobiles et ne sont pas destinées aux bricoleurs ou aux personnes non professionnelles.

Elles ne contiennent pas d’instructions sur les installations électriques ni d’avertissements sur les dangers potentiels des coussins

gonﬂ ables, des systèmes antivol et du système de freinage ABS ou autres systèmes, d’avertissement qui sont indispensables pour

installer cet appareil. Toute tentative d’installer cet appareil dans un véhicule par une personne autre qu’un installateur professionnel

pourrait endommager le système de sécurité électrique, et pourrait provoquer des blessures physiques graves, voire la mort.

SSi votre voiture est équipée de coussins gonﬂ ables et/ou d’un système antivol, des procédures spéciﬁ ques sont parfois requises

pour la connexion et la déconnexion de la batterie pour installer cet appareil. Avant de tenter malgré tout l’installation de ce composant

électronique contrairement aux recommandations du fabricant, vous devez prendre contact avec votre revendeur ou votre constructeur

automobile pour déterminer la procédure requise et vous conformer strictement à leurs instructions.

LE FAIT DE NE PAS SUIVRE CETTE PROCÉDURE PEUT PROVOQUER UN DÉPLOIEMENT DES COUSSINS GONFLABLES OU L’ACTIVATION DU

SYSTÈME ANTI-VOL POUVANT ENDOMMAGER LE VÉHICULE OU PROVOQUER DES BLESSURES PHYSIQUES, VOIRE LA MORT.

La información de instalación va dirigida a instaladores profesionales con conocimientos de los sistemas de seguridad eléctricos de los

automóviles y no se ha preparado para individuos sin conocimientos técnicos. No contiene instrucciones sobre la instalación eléctrica ni

advertencias relacionadas con los posibles daños en los airbag, sistema antirrobo y de frenos ABS, ni otros sistemas, que pueden causarse

al intentar instalar este producto. Cualquier intento de instalar este producto en un vehículo motorizado por parte de una persona que no sea

un instalador cualiﬁ cado podrá causar daños en los sistemas eléctricos de seguridad, pudiendo causar heridas graves o incluso la muerte.

SSi su automóvil está provisto de sistemas de airbags y/o antirrobo, pueden resultar necesarios unos procedimientos especíﬁ cos

para conectar y desconectar la batería a ﬁ n de instalar este producto. Antes de intentar instalar este componente electrónico en contra

a las recomendamos del fabricante, deberá ponerse en contacto con el concesionario o fabricante de su automóvil para determinar el

procedimiento requerido y deberá seguir estrictamente sus instrucciones.

Antes de la instalación

Before Installation/Avant l’installation/

SI NO SIGUE EL PROCEDIMIENTO INDICADO PUEDE RESULTAR EN QUE SE INFLEN ACCIDENTALMENTE LOS AIRBAG O SE ACTIVE EL SISTEMA

ANTIRROBO, RESULTANDO EN DAÑOS EN EL VEHÍCULO Y HACIÉNDOLE CORRER EL PELIGRO DE HERIDAS PERSONALES O DE MUERTE.

installation.

Consult a professional for installation.

• Verify the radio using the antenna and speakers before

Prenez contact avec un spécialiste pour le montage.

y los altavoces antes de realizar la instalación.

• Vériﬁ ez l’autoradio avant de procéder au montage.

Para realizar la instalación consulte a un profesional.

• Veriﬁ que el funcionamiento de la radio empleando la antena

: horizontal

: 0 – 30°

: horizontal

front to rear

• Mounting angle right to left

• Angle de montage latéral

0 – 30e

: horizontal

: 0 – 30°

: 0 à 30°

longitudinal

Delante a atrás

Ángulo de montaje Lado a lado

Dashboard/Tableau de bord/Tablero de instrument

•

THICKNESS/ÉPAISSEUR/GROSOR

MIN. 4.75 mm {3/16”}/{3/16 po}/{3/16”}

{2 3/32”}

{2 3/32 po}

{2 3/32”}

53 mm

{7 5/32”}

{7 5/32 po}

{7 5/32”}

182 mm

MAX. 5.56 mm {7/32”}/{7/32 po}/{7/32”}





Remove the face plate.

Retirez le panneau

avant.

Extraiga el panel frontal.



Extracción de la unidad

How to remove the unit/Retrait de l’appareil/







Remove the trim plate

Enlevez la plaque de

garniture

Extraiga la placa de

guarnición



dans l’appareil



into the main unit.



Lock release



en la unidad



until you hear a click.



Pull the main unit.

Insert the lock cancel plate







jusqu’à



antiblocage

entendre un clic.

principal.

Introduisez la plaque

Dégager l’appareil

Libération du verrouillage







cancelación de bloqueo

hasta oír un sonido seco

de conﬁ rmación.

Inserte la placa de

Desbloqueo

Tire de la unidad principal.





Pull out the unit with

both hands.

Retirez l’appareil à deux

mains.

Extraiga la unidad con

ambas manos.

Remove the cable from the battery negative terminal.

Retirez le câble de la borne négative de la batterie.

Extraiga el cable del terminal negativo de la batería.

Bend appropriate tabs to secure the unit

without backlash.

Repliez les languettes de ﬁ xation

appropriées pour

immobiliser l’appareil

sans contrecoup.

Doble las lengüetas

apropiadas para ﬁ jar la

. Repliez les languettes

. Doble las lengüetas de



insertion. Bend mounting tabs.



Mounting collar

Insertion du cadre de montage

de ﬁ xation.

Inserción del collar de montaje

montaje.

principal.

chaque trou.

Screw the mounting bolt



Secure to the ﬁ re wall. Snap the right and left springs into each hole. Visser le boulon de ﬁ xation





Main unit

securing

unidad sin contragolpe.



Fixez au tablier. Engager les ressorts gauche et droit dans



Fixation de

l’appareil

principal

principal.

Enrosque el perno de montaje

Fíjelo a la pantalla cortafuegos. Acople los resortes derecho e izquierdo en





Fijación de la

unidad principal



Connection of power connector

Raccordement du connecteur d’alimentation

Conexión del conector de alimentación

cada oriﬁ cio.

Caution

When this unit is installed in dashboard, ensure



Précaution

that there is sufﬁ cient air ﬂ ow around the unit to

Lorsque cet appareil est installé dans le

tableau de bord, assurez-vous qu’il y a une

prevent damage from overheating, do not block

any ventilation holes on the unit.

circulation d’air sufﬁ sante autour de l’appareil

mounting



Trim plate

Installation de la plaque de

garniture Montaje de la placa de

Clank!

Precaución

aﬁ n d’éviter tout endommagement provoqué

par une surchauffe et qu’aucun trou d’aération

de l’appareil n’est obturé.



guarnición

Raccordement du câble

Battery Cable reconnection

Snapping point

Point d’encliquetage

Punto de

acoplamiento

Cuando instale esta unidad en el tablero

de instrumentos, asegúrese de que haya

suﬁ ciente ventilación de aire en torno a

la unidad para evitar daños debidos al

sobrecalentamiento, y no obstruya ningún

Reconexión de cables

oriﬁ cio de ventilacion de la unidad.

Plaque-support arrière (En option)

Regleta de soporte trasera

Rear support strap (Optional)

Tapping screw (Optional)

Vis taraudeuse (En option)

Tornillo de autoenrosque (opcional)

(opcional)

To the unit

Côté appareil

A la unidad



How to install the unit/Mode de montage de l’appareil/Instalación de la unidad

Caution

Installation/Montage/Instalación

• Wear gloves for safety.

• Make sure that wiring is completed before

installation.

Précaution

Precaución

Assurez-vous que le câblage est terminé avant l’installation.

• Portez des gants à des ﬁ ns de sécurité.

•

eléctricas antes de realizar la instalación.

• Póngase guantes para mayor seguridad.

• Asegúrese de haber completado todas las conexiones

Utilisation de la barrette de support arrière (En option)

Empleo de la correa de soporte trasera (opcional)

Using the rear support strap (Optional)



3 mm







Mounting Bolt

Rubber Bushing

Bague en caoutchouc

Buje de goma



Boulon de ﬁ xation Perno de montaje

Mounting Bolt

Boulon de ﬁ xation Perno de montaje

To the unit

Côté appareil

A la unidad

Hexagonal nut (Optional)

Écrou hexagonal (En option)

Tuerca hexagonal (opcional)



Using the rubber bushing Utilisation de la bague en caoutchouc

Fijación a la pared cortafuegos

Empleo del buje de goma

Securing to ﬁ re wall

Fixation au tablier

Rear support bracket

(supplied with car)

Support arrière

(fourni avec votre voiture)

Ménsula de soporte trasera

(suministrada con el

vehículo)

Front Left + (White)

Avant gauche + (Blanc)

Delantero izquierdo + (Blanco)

Front Left – (White w/black stripe)

Avant gauche – (Blanc rayé noir)

Delantero izquierdo – (Blanco con franja negra)

Front Right – (Gray w/black stripe)

Avant droit – (Gris rayé noir)

Front Right + (Gray)

Avant droit + (Gris)

Delantero derecho – (Gris con franja negra)

Delantero derecho + (Gris)

Caution

Précaution

To prevent damage to the unit, do not connect the power connector

until the whole wiring is completed.

Ne raccordez pas le connecteur d’alimentation sur l’appareil avant

Precaución

d’avoir effectué tous les raccordements pour éviter d’endommager

l’appareil.

Para evitar daños en la unidad, no conecte el conector de

alimentación hasta haber completado todas las conexiones.

Fuse (15 A) Refer fuse replacement to your nearest authorized Panasonic

Servicenter. Do not try fuse replacement by yourself.

Fusible (15 A) Conﬁ ez le remplacement de fusible au centre de service

après-vente Panasonic agréé le plus proche. N’essayez pas de remplacer

le fusible tout(e) seul(e).

Fusible (15 A) Solicite el reemplazo del fusible al centro de servicio

Panasonic autorizado que le quede más cerca. No trate de reemplazar

usted mismo el fusible.

(Red)/(Rouge)/(Rojo)

Power Lead (ACC or IGN) To ACC power, +12 V DC.

Fil d’alimentation (ACC ou IGN) À l’alimentation ACC, +12 V CC.

Cable de la alimentación (ACC o IGN) A la alimentación de ACC, +12 V CC.

(Black)/(Noir)/(Negro)

ACC

Ground Lead To a clean, bare metallic part of the car chassis.

Fil de mise à la masse À une partie métallique propre découverte du châssis de voiture.

Cable de toma de tierra A una parte metálica limpia y desnuda del chasis del vehículo.

(Yellow)/(Jaune)/(Amarillo)

Battery Lead To the car battery, continuous +12 V DC.

Fil de batterie À la batterie de voiture, alimentation continue de +12 V CC.

Cable de la batería A la batería del vehículo, +12 V CC continuos.

(Blue w/white stripe)/(Bleu rayé blanc)/(Azul con franja blanca)

External Ampliﬁ er Control Lead To an external ampliﬁ er. (Max 100 mA) (synchronized with the power on/off of ampliﬁ er)

Motor Antenna Relay Control Lead To Motor Antenna. (Max 100 mA) (This lead is not intended for use with a switch actuated power antenna).

d’alimentation de l’ampliﬁ cateur)

Fil de commandes de l’antenne À l’antenne motorisée. (100 mA maxi.) (Ce ﬁ l n’est pas conçu pour l’usage avec une antenne commandée par interrupteur).

Fil de commandes de l’ampliﬁ cateur externe À l’ampliﬁ cateur de puissance Panasonic. (100 mA maxi.) (synchronisé avec l’application ou la coupure

Cable de control del ampliﬁ cador externo Al ampliﬁ cador de potencia Panasonic. (Máx. 100 mA) (sincronizado con la conexión/desconexión del ampliﬁ cador)

Cable de control de la antena A la antena de motor. (Máx. 100 mA) (Este cable no está diseñado para ser utilizado con una antena de alimentación accionada mediante interruptor.)

Rear Right – (Violet w/black stripe)

Arrière droit – (Violet rayé noir)

Trasero derecho – (Violeta con franja negra)

Trasero derecho + (Violeta)

BATTERY 15A

Rear Left + (Green)

Arrière gauche + (Vert)

Trasero izquierdo + (Verde)

Rear Left – (Green w/black stripe)

Arrière gauche – (Vert rayé noir)

Trasero izquierdo – (Verde con franja negra)

Rear Right + (Violet)

Arrière droit + (Violet)

Wiring/Câblage/Conexiones eléctricas

(L)/(G)/(lzq.)

(White)/(Blanc)/(Blanco)

Antenna

Antenne

(R)/(D)/(Der.)

(Red)/(Rouge)/(Rojo)

Preamp Out Connector (Rear)

Conector de salida de preampliﬁ cador (Posterior)

Connecteur de sortie de préampliﬁ cateur (arrière)

CQ-C1335L

CQ-C1335U

Preamp Out Connector (Front)

Connecteur de sortie de préampliﬁ cateur (Avant)

Conector de salida de preampliﬁ cador (Frontal)

FRONT SP

REAR SP

can cause burning, smoking or damage of the speakers.

• Use ungrounded speakers only.

Allowable input: 50 W or more

Impedance: 4 – 8 j

Use of speakers which do not match the specifications

• Distance between speaker and ampliﬁ er: 30 cm {12”} or more

• Utilisez uniquement des haut-parleurs non reliés à la masse.

pas aux caractéristiques techniques adéquates peut

provoquer un dégagement de fumée, l’inflammation ou

Puissance d’entrée admissible: 50 W ou davantage

l’endommagement des haut-parleurs.

Impédance: 4 – 8 j

L’utilisation de haut-parleurs qui ne correspondent

• Distance entre le haut-parleur et l’ampliﬁ cateur: 30 cm

{12 po} ou davantage

especificaciones indicadas puede hacer que los altavoces

• Emplee solamente altavoces sin toma de tierra.

se quemen, echen humo o sufran daños.

Entrada permisible: 50 W o más

Impedancia: 4 – 8 j

La utilización de altavoces que no cumplan con las

• Distancia entre el altavoz y el ampliﬁ cador: 30 cm {12”} o más

• Do not use a 3-wire type speaker

system having a common earth lead.

• N’utilisez pas de système de haut-

parleur de type à 3 ﬁ ls ayant un ﬁ l de

mise à la masse commun.

• No emplee sistemas de altavoz del

tipo de 3 cables con cable de masa

común.

Speaker Connection/Raccordement avec les haut-parleurs/Conexión de los altavoces

Connect as follows.

Raccordez les haut-parleurs comme suit.

Conecte de la forma siguiente.

Comprobación ﬁ nal

Final Check/Vériﬁ cations ﬁ nales/

1. Make sure that all wires are properly connected and insulated.

2. Make sure that the main unit is securely held in the mounting collar.

3. Turn on the ignition to check the unit for proper operation.

If you have difﬁ culties, consult your nearest authorized professional

montage.

installer for assistance.

1. Assurez-vous que tous les ﬁ ls sont bien raccordés et isolés.

2. Assurez-vous que l’appareil est solidement en place dans son collier de

3. Faites démarrer la voiture et vériﬁ ez le fonctionnement de l’appareil.

En cas de difﬁ culté, consultez un installateur professionnel.

Caution

aislados.

collar de montaje.

1. Asegúrese de que todos los cables estén correctamente conectados y

unidad.

2. Asegúrese de que la unidad principal quede ﬁ jada con seguridad en el

3. Conecte el encendido para comprobar el correcto funcionamiento de la

Si tiene alguna diﬁ cultad, consulte al instalador profesional que le quede

más cerca para que le ayude.

Précaution

set of speaker leads. (except for connecting to a

tweeter)

• Do not connect more than one speaker to one

ensemble de ﬁ ls de haut-parleur. (Sauf lors du

raccordement à un haut-parleur d’aigus)

• Ne raccordez pas plus d’un haut-parleur à un

Precaución

cables de altavoz. (excepto para la conexión a

un altavoz de agudos)

• No conecte más de un altavoz a un juego de

Instalación ﬁ nal

Final Installation/Installation ﬁ nale/

Lead Connections

Connect all wires, making sure that each connection is insulated and

secure. Bundle all loose wires and fasten them with tape so they will not

fall down later. Now insert the unit into the mounting collar.

Congratulations! After making a few ﬁ nal checks, you’re ready to enjoy

your new auto stereo system.

Câblage

Raccordez tous les ﬁ ls en prenant soin qu’ils soient tous bien isolés et

solidement connectés. Enroulez toute longueur excessive de ﬁ l et ﬁ xez-la

en place avec une ruban adhésive. Installez l’appareil dans son collier de

montage.

Félicitations! Après avoir effectué quelques vériﬁ cations ﬁ nales, vous êtes

prêt à proﬁ ter pleinement de votre nouveau système autoradio.

Conexiones de cables

Conecte todos los cables, asegurándose de que cada conexión queda

aislada y segura. Agrupe todos los cables sueltos y fíjelos con cinta

para que no queden colgando. Inserte entonces la unidad en el collar de

montaje.

¡Enhorabuena! Después de realizar algunas comprobaciones ﬁ nales,

estará preparado para disfrutar de su nuevo sistema estéreo para

automóvil.

Panasonic CQ-C1335L, CQ-C1305L User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual