Panasonic CQC-1110-AN, CQC-1110-GN, CQC-1110-VN, CQC-1120-AN, CQC-1120-GN Service manual

Specifications*
ORDER NO. ACED040125C8
AUTOMOTIVE AFTERMARKET
CQ-C1120AN CQ-C1120GN CQ-C1110AN CQ-C1110GN CQ-C1100VN
CD Player/Receiver
General
Power Supply 12V DC(11V-16V),
Test Voltage 14.4V
Negative Ground Tone Control (Bass) ±12dB at 100Hz Tone Control (Treble) ±12dB at 10Hz Current Consumption Less than 2.5A
(CD mode; 0.5W × 4-speaker) Maximum Power Output 45W × 4 (at 4) Power Output 20W × 4 (DIN45 324, at 4) Speaker Impedance 4-8 Pre-amp Output Voltage 2.5V (CD mode) Pre-amp Output Impedance 200
CD Player
Sampling Frequency 8 Times Oversampling Pick-up Type Astigma 3-Beam Light Source Semiconductor Laser Wave Length 780 nm Frequency Response 20 Hz-20kHz (±1dB) Signal to Noise Ratio 96dB Total Harmonic Distortion 0.01% (1kHz) Wow and Flutter Below Measurable Limits Channel Separation 75dB
Radio FM
Frequency Range 87.5MHz - 108MHz Usable Sensitivity 6dB/µV(S/N 30dB) Stereo Separation 35dB (at 1kHz)
MW
Frequency Range 531kHz - 1,602kHz Usable Sensitivity 28dB/µV (S/N 20dB)
LW
Frequency Range 153kHz - 279kHz Usable Sensitivity 32dB/µV (S/N 20dB)
Dimensions (W×H×D)** 178×50×155mm Weight** 1.4 kg
* Specifications and the design are subject to possible modification without notice due to improvements.
** Dimensions and Weight shown are approximate. ** Above specifications comply with EIA standards.
© 2004 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
CQ-C1120AN / CQ-C1120GN / CQ-C1110AN / CQ-C1110GN / CQ-C1100VN
CONTENTS
Page Page
1 ABOUT LEAD FREE SOLDER (PbF) 3 2 FEATURES 3 FUSE 4 MAINTENANCE 5 NOTES 6 DIMENSIONS 7 LASER PRODUCTS 8 WIRING CONNECTION 9 BLOCK DIAGRAM
10 TERMINALS DESCRIPTION 11 PACKAGE AND IC BLOCK DIAGRAM
3 3
12 REPLACEM ENT PARTS LIST 13 EXPLODED VIEW (Unit)
3 3
14 C D PLAYER MECHANISM PART
3
15 EXPLODED VIEW (CD Deck) 16 WIRING DIAGRAM
3 4
17 SCHEMATIC DIAGRAM-1 18 SCHEMATIC DIAGRAM-2
5
7
9 12 18 19 20 21 25 27
2
CQ-C1120AN / CQ-C1120GN / CQ-C1110AN / CQ-C1110GN / CQ-C1100VN
1 ABOUT LEAD FREE
SOLDER (PbF)
Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF
stamp on the PCB.
Caution :
Pb free solder has a higher melting point than standard
• •
solder; Typically the melting point is 50 - 70°F (30 ­40°C) higher. Please use a soldering iron with temperature control and adjust it to 700 ± 20°F (370 ± 10°C). In case of using high temperature soldering iron, please be careful not to heat too long.
Pb free solder will tend to splash when heated too high
• •
(about 1100°F/600°C)
This lead free solder will be used for the products after
• •
serial No. 1,000,001.
2 FEATURES
Sound System with Spurting Realism
• •
(2-channel or 4-channel Power Amplifier)
Powerful Heavy Bass
• •
(Stereo/Mono Power Amplifier) : CY-M7052EN/CY­M9054EN
Radio Data System (RDS)
• •
Not support 8 cm discs
• •
Not compatible with MP3/WMA
• •
5 NOTES
[RADIO BLOCK]
Do not align the AM/FM package block. When the package block is necessary, it will be supplied already aligned at the factory.
[CD DECK BLOCK]
This model has no servo alignment points because microcomputer controls the servo circuit
6 DIMENSIONS
7 LASER PRODUCTS
3 FUSE
Use fuses of the same specified rating (15A).
• •
Using different substitutes or fuses with higher rating, or
• •
connecting the unit directly without a fuse, could cause fire or damage to the unit.
4 MAINTENANCE
Wipe the unit with a soft dry cloth.
• •
Never apply volatile liquids such as benzine and thinner to
• •
prevent damage.
3
CQ-C1120AN / CQ-C1120GN / CQ-C1110AN / CQ-C1110GN / CQ-C1100VN
8 WIRING CONNECTION
4
9 BLOCK DIAGRAM
9.1. Main/Display Block
CQ-C1120AN / CQ-C1120GN / CQ-C1110AN / CQ-C1110GN / CQ-C1100VN
5
CQ-C1120AN / CQ-C1120GN / CQ-C1110AN / CQ-C1110GN / CQ-C1100VN
9.2. CD Servo Block
6
10 TERMINALS DESCRIPTION
CQ-C1120AN / CQ-C1120GN / CQ-C1110AN / CQ-C1110GN / CQ-C1100VN
10.1. Main Block
Pin No.
1 NC (Ground pull down) I 0 0 0 2 NC (Ground pull down) I 0 0 0 3 NC (Ground pull down) I 0 0 0 4 AVSS Ground - 0 0 0 5 AF_MUTE AF mute O/I 5 5 5.1 6 AMP_CNT Amp control O 5 5 5.1 7 AVREF1 (Conecting to +5V) - 5 5 5.1 8 CD_S0 CD data I 0 0 0
9 CD_SI CD data O 0 0 2.8 10 CD_SCK CD clock O 0 0 5 11 CDC_DATA(NC) No connection - - - ­12 BATT BATT detection I 5 5 5 13 CDC_CLK(NC) No connection - - - ­14 REW_OUT(NC) No connection - - - ­15 BZ_OUT Buzzer signal output O 0 0 0 16 PLL_D0 PLL data I 5.1 5.1 5.1 17 PLL_DI PLL data O 0 0 0 18 PLL_CLK PLL clock O 5 5 5.1 19 PLL_CE PLL chip enable O 0 0 0 20 NC No connection - - - ­21 NC No connection - - - ­22 MUTE Mute control output O 5 5 5.1 23 NC No connection - - - ­24 CD_STB CD strobe - 0 0 5 25 CD_AO CD AO - 0 0 4.4 26 CD_RST(NC) No connection - - - ­27 CD_RFOK CD RFOK I 0 0 4.9 28 CD_LOCK CD lock I 0.5 0.3 4.9 29 CD_LIMIT CD limit I 0 0 5 30 CD_SW2 CD SW2 I 5 5 0 31 NC No connection - - - ­32 NC No connection - - - ­33 VSS1 Ground - 0 0 0 34 NC No connection - - - ­35 ST FM stereo signal input I 5 5.1 5 36 SCL Audio control clock O 5 5 5.1 37 SDA Audio control data I/O 5 5 5.1 38 S_LED(NC) No connection - - - ­39 NC No connection - - - ­40 NC No connection - - - ­41 LCD_DI LCD driver data O 0 0 0 42 LCD_DO LCD driver data I 5 5 5 43 LCD_CLK LCD driver clock O 0 0 0 44 LCD_CE LCD driver chip enable O 0 0 0 45 POW_LED Power LED O/I 0 0 0 46 ANT_CNT(NC) No connection - - - ­47 ILL_CNT(NC) No connection - - - ­48 NC No connection - - - ­49 REM.IN_SUB Remote control sub data I 5 5 5 50 NC No connection - - - ­51 NC No connection - - - ­52 NC No connection - - - ­53 NC No connection - - - ­54 TEL MUTE TEL mute I 5 5 5 55 PANEL PANEL in detection I 4.8 4.8 4.8 56 CD_CNT CD power control O 0 0 5 57 PWR_CNT Main power control O 5 5 5.1 58 NC No connection - - - ­59 RDS_DATA RDS data input I 2.8 0 2.8 60 RESET System reset I 5 5 5.1 61 REM_DATA Remote control data I 5 5 5
Port Description I/O (V)
IC601 : C2CBHF000322
FM AM CD
Pin No.
62 CD_SW1 CD SW1 signal input I 0 0 0 63 RDS_CLK RDS clock input I 2.6 2.5 2.6 64 CDC_STB Changer strobe signal I 0 0 0 65 ROT.1 Rotary encoder signal 1 I 5 5 5.1 66 ROT.2 Rotary encoder signal 2 I 5 5 5.1 67 VSS0 Ground - 0 0 0 68 VDD1 +5V power supply - 5 5 5.1 69 X2 Crystal oscillator - 2.8 2.8 2.8 70 X1 Crystal oscillator I 2.6 2.6 2.6 71 VPP Vpp - 0 0 0 72 XT2 SUB Crystal oscillator - 2.8 2.8 2.8 73 XT1 SUB Crystal oscillator I 2.5 2.5 2.5 74 VDD0 +5V power supply - 5 5 5.1 75 AVREF +5V power supply - 5 5 5.1 76 VSM FM/AM SD input I 0.5 0.8 0 77 ACC ACC detection I 5.2 5.2 5.2 78 INIT_A (+5V pull up) I 5 5 5.1 79 NC (Ground pull down) I 0 0 0 80 NC (Ground pull down) I 0 0 0
Port Description I/O (V)
FM AM CD
10.2. Display Block
Pin No. Port Description I/O (V)
1-35 S1-35 LCD segment data O 2.5 36-39 NC No connection - ­40-43 COM1-4 LCD common O 2.5
44 KS1 Not used - ­45-49 KS2-6 Key scan O 5 50-54 Kl1-5 Key data I 0
55 TEST (Connecting to ground) - 0
56 VDD +5V power supply - 5
57 VDD1 VDD1 filter terminal - 3.3
58 VDD2 VDD2 filter terminal - 1.7
59 VSS Ground - 0
60 OSC Oscillator terminal - 3.9
61 DO Key data output O 5
62 CE LCD driver chip enable I 0
63 CLK LCD clock I 4.9
64 DI LCD data I 4.9
IC901 : YEAMLC75854T
7
CQ-C1120AN / CQ-C1120GN / CQ-C1110AN / CQ-C1110GN / CQ-C1100VN
10.3. CD Servo Block
Pin No.
10 D.VDD Digital Power Supply - 4.9 11 DA.VDD D/A Converter Power Supply - 4.7 12 ROUT R-channel Audio Signal Output O 3.3 13 DA.GND D/A Converter Ground - 0 14 REGC Capacitor Connection for Regulator - 3.4 15 DA.GND D/A Converter Ground - 0 16 LOUT L-channel Audio Signal Output O 3.3 17 DA.VDD D/A Converter Power Supply - 4.6 18 R+(NC) No connection - ­19 R-(NC) No connection - ­20 L-(NC) No connection - ­21 L+(NC) No connection - ­22 X.VDD Crystal Oscillator Power Supply - 4.8 23 XTAL Crystal Connection O 2.3 24 /XTAL Crystal Connection I 2.1 25 X.GND Crystal Oscillator Ground - 0 26 D.VDD Digital Power Supply - 4.7 27 EMPH(NC) No connection - ­28 FLAG(NC) No connection - ­29 DIN Data Input I 2.5 30 DOUT Data Output O 2.5 31 SCKIN Serial Clock Input I 2.7 32 SCKO Serial Clock Output O 2.7 33 LRCKIN LR Clock Input I 2.5 34 LRCK LR Clock O 2.5 35 HOLD/WDC
36 TX(NC) No connection - ­37 D.GND Digital Ground - 0 38 C16M(NC) No connection - ­39 LIMIT(NC) No connection - ­40 D.VDD Digital Power Supply - 4.9 41 LOCK Lock O 4.9 42 RFCK(NC) No connection - ­43 MIRR/WFC
44 PLCK(NC) No connection - ­45 D.GND Digital Ground - 0 46 C1D1(NC) No connection - ­47 C1D2(NC) No connection - ­48 C2D1(NC) No connection - ­49 C2D2(NC) No connection - ­50 C2D3(NC) No connection - ­51 D.VDD Digital Power Supply - 4.9 52 PACK(NC) No connection - ­53 TSO(NC) No connection - ­54 TSI Parameter Input for Text Data I 0 55 /TSCK Serial Clock for Text Data I 0 56 TSTB Text Parameter Strobe I 0 57 D.GND Digital Ground - 0 58 TEST0 Test I 0 59 TEST1 Test I 0 60 ATEST Analog Test O 2.0 61 A.GND Analog Ground - 0 62 FD Focus Drive O 2.5
Port Description I/O (V)
1 D.GND Digital Ground - 0 2 RFOK RFOK Signal O 4.9 3 /RESET Reset I 4.9 4 A0 Address 0 I 4.0 5 /STB Strobe I 4.9 6 /SCK Serial Clock I 4.9 7 SO Serial Data Output O 0 8 SI Serial Data Input I 3.0 9 /XTALEN Crystal Oscillaton Enable I 0
K(NC)
K(NC)
IC1 : C1BB00000665
No connection - -
No connection - -
Pin No.
63 TD Tracking Drive O 2.5 64 SD Sled Drive O 2.6 65 MD Motor Drive O 2.5 66 DAC0(NC) No connection - ­67 DAC1(NC) No connection - ­68 DAC2(NC) No connection - ­69 DAC3(NC) No connection - ­70 A.VDD Digital Power Supply - 4.9 71 EFM EFM Signal O 2.7 72 ASY Slice Level I 2.4 73 C3T Capacitance Connection for 3T Signal
74 RFI RF Signal Input I 2.4 75 AGCO AGC Amp Output O 2.4 76 AGCI AGC Amp Input I 2.4 77 RFO RF Amp Output O 2.7 78 EQ2 Equalizer Parts Connection for RF
79 EQ1 Equalizer Parts Connection for RF
80 RF- Impedance Connection to RF Amp for
81 A.GND Analog Ground - 0 82 A Error Signal Input I 2.7 83 C(NC) No connection - ­84 B Error Signal Input I 2.7 85 D(NC) No connection - ­86 F Error Signal Input I 2.9 87 E Error Signal Input I 2.9 88 A.VDD Analog Power Supply - 4.9 89 REFOUT Reference Output O 2.5 90 FE- Impedance Connection to Focus Error
91 FEO Focus Error Amp Output O 2.5 92 TE- Impedance Connection to Ttacking
93 TEO Tracking Error Amp Output O 2.5 94 TE2 Tracking Error Amp Output Multiplied
95 TEC Tracking Error Comparator I 2.5 96 A.GND Analog Ground - 0 97 PD Photo Diode Signal (for Detecting
98 LD Laser Diode Control Current Output O 3.6 99 PN APC Circuit Polarity Control I 0
100 A.VDD Analog Power Supply - 4.9
Port Description I/O (V)
- 2.7
Detecting Circuit
- 2.5
Amp
- 0.3
Amp
I 2.3
Negative Feedback
I 2.5
Amp for Negative Feedback
I 2.5
Error Amp for Negative Feedback
O 2.6
by Two
I 0.2
Laser Power) Input
8
CQ-C1120AN / CQ-C1120GN / CQ-C1110AN / CQ-C1110GN / CQ-C1100VN
11 PACKAGE AND IC BLOCK DIAGRAM
11.1. Main Block
IC201 : C1BB00000543
IC401 : C1BB00000644
9
CQ-C1120AN / CQ-C1120GN / CQ-C1110AN / CQ-C1110GN / CQ-C1100VN
IC271 : C1EA00000036
IC701 : C0DAZHH00007
IC702 : MN1382QTX
10
IC901 : YEAMDA7479D
Loading...
+ 22 hidden pages