Panasonic awhr140pj Operation Manual

Operating Instruction

HD Integrated Camera

Model No.

AW-HR140PJ AW-HR140EJ

Before operating this product, please read the instructions carefully and save this manual for future use. Please carefully read the “Read this first!” (pages 2 to 4) of this Manual before use.

ENGLISH

W0617TY0 -FJ

DVQP1343ZA

Read this first! (For AW-HR140PJ)

WARNING:

• To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.

• To reduce the risk of fire or electric shock, keep this equipment away from all liquids. Use and store only in locations which are not exposed to the risk of dripping or splashing liquids, and do not place any liquid containers on top of the equipment.

CAUTION:

In order to maintain adequate ventilation, do not install or place this unit in a bookcase, built-in cabinet or any other confined space. To prevent risk of electric shock or fire hazard due to overheating, ensure that curtains and any other materials do not obstruct the ventilation.

CAUTION:

WARNING:

Always keep the mounting bolt, washer, spring washer and drop-prevention wire mounting screw out of the reach of infants and small children.

To reduce the risk of fire or electric shock and annoying interference, use the recommended accessories only.

CAUTION:

Check the installation at least once a year.

CAUTION:

Do not remove panel covers by unscrewing. To reduce the risk of electric shock, do not remove the covers. No user serviceable parts inside. Refer servicing to qualified service personnel.

An improper installation could cause the unit to fall off resulting in personal injury.

FCC NOTICE (USA)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION:

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Warning:

To assure continued FCC emission limit compliance, follow the attached installation instructions and the user must use only shielded interface cables when connecting to host computer or peripheral devices. Also, any unauthorized changes or modifications to this equipment could void the user’s authority to operate this device.

NOTIFICATION (Canada)

CAN ICES-3 (A)/NMB-3(A)

indicates safety information.

Read this first! (For AW-HR140EJ)

WARNING:

• To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.

WARNING:

Always keep the mounting bolt, washer, spring washer and drop-prevention wire mounting screw out of the reach of infants and small children.

WARNING:

This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.

CAUTION:

Do not remove panel covers by unscrewing. To reduce the risk of electric shock, do not remove the covers. No user serviceable parts inside. Refer servicing to qualified service personnel.

CAUTION:

To reduce the risk of fire or electric shock and annoying interference, use the recommended accessories only.

CAUTION:

Check the installation at least once a year. An improper installation could cause the unit to fall off resulting in personal injury.

indicates safety information.

AEEE Yönetmeliğine Uygundur. AEEE Complies with Directive of Turkey.

Read this first! (For AW-HR140EJ) (continued)

Вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в електричному та електронному обладнанні

(затвердженого Постановою №1057 Кабінету Міністрів України)

Виріб відповідає вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в електричному та електронному обладнанні (ТР ОВНР).

Вміст небезпечних речовин у випадках, не обумовлених в Додатку №2 ТР ОВНР, :

1. свинець(Pb) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;

2. кадмій (Cd)– не перевищує 0,01 % ваги речовини або в концентрації до 100 частин на мільйон;

3. ртуть(Hg) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;

4. шестивалентний хром (Cr6+ ) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;

5. полібромбіфеноли (PBB) – не перевищує 0,1% ваги речовини або в концентрації до 1000 частин на мільйон;

6. полібромдефенілові ефіри (PBDE) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон.

Read this first <END>

Декларація про Відповідність

Manufactured by: Panasonic Corporation, Osaka, Japan Importer’s name and address of pursuant to EU rules:

Panasonic Marketing Europe GmbH Panasonic Testing Centre Winsbergring 15, 22525 Hamburg, Germany

Read this first! (continued)

EXT

MODE

SDI OUT

1/PM 2G/L IN

POWER/

STANDBY

Note on grounding

• Ground the unit via the <SIGNAL GND> ground connector.

POWER/

SDI OUT

10BASE-T/

STANDBY

1/PM 2G/L IN

100BASE-TX

RS-422

12V IN

Ground connector

ACT LINK

12V IN

SIGNAL GND

PUSH

AUDIO IN(1/2)

PUSH

MODE

EXT

SIGNAL GND

to ground

connector on wall

outlet, ground bar, etc.

Trademarks and registered trademarks



• Microsoft®, Windows®, Windows® 7, Windows® 8, Windows® 8.1, Windows

10, Internet Explorer®, ActiveX® and DirectX® are either

registered trademarks or trademarks of Microsoft Corporation in the United States and other countries.

• Apple, Mac, OS X, iPhone, iPod Touch, iPad, and Safari are registered trademarks of Apple Inc., in the United States and other countries.

• Android™ is a trademark of Google Inc.

• Intel

and Intel® CoreTM are trademarks or registered trademarks

of Intel Corporation in the United States and other countries.

• Adobe

and Reader® are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.

• Other names of companies and products contained in these Operating Instructions may be trademarks or registered trademarks of their respective owners.

About copyright and licence



Distributing, copying, disassembling, reverse compiling, reverse engineering, and also exporting in violation of export laws of the software provided with this unit are expressly prohibited.

Abbreviations



The following abbreviations are used in this manual.

• Microsoft

to “Windows 7”.

• Microsoft

“Windows 8”.

• Microsoft

“Windows 8.1”.

• Microsoft

“Windows 10”.

• Windows Explorer Internet Explorer

Windows® 7 Professional SP1 32/64-bit is abbreviated

Windows® 8 Pro 32/64-bit is abbreviated to

Windows® 8.1 Pro 32/64-bit is abbreviated to

Windows® 10 Pro 32/64-bit is abbreviated to

Internet Explorer® 8.0, Windows® Internet

9.0, Windows® Internet Explorer® 10.0 and Windows®

11.0 are abbreviated to “Internet Explorer”.

For the purposes of this manual, the model numbers of the units are given as listed in the table below.

Model number of unit

AW-HR140PJ

AW-HR140EJ

AW-HS50N

AW-HS50E

AW-RP50N

AW-RP50E

Model number given in

manual

AW-HR140

AW-HS50

AW-RP50

AW-RP120G AW-RP120

AK-HRP200G AK-HRP200

Illustrations and screen displays featured



in the manual

• What is shown in the manual’s illustrations and screen displays may differ from how it is actually appears.

• Functions which can be used by Windows only are indicated using the

• The screenshots are used in accordance with the guidelines of Microsoft Corporation.

mark.

Contents

Read this first! (For AW-HR140PJ) ......................................................2

Read this first! (For AW-HR140EJ) ......................................................3

Note on grounding ............................................................................... 5

Before use ..............................................................................................7

Overview .............................................................................................. 7

Computer requirements ....................................................................... 7

Disclaimer of warranty ......................................................................... 8

Network security .................................................................................. 8

Features.................................................................................................. 9

Controller supported ........................................................................... 10

Accessories .........................................................................................11

Operating precautions ........................................................................ 12

Parts and their functions .................................................................... 14

AW-RP50 (not supplied) ......................................................................16

Network settings.................................................................................. 21

Use the Easy IP Setup Software to establish the unit’s settings........ 21

Installing the plug-in viewer software ................................................. 22

Enable the user authentication function ............................................. 22

Basic shooting operations .................................................................23

How to turn the power on and off ...................................................... 23

Turning the power on ......................................................................... 23

Turning the power off ......................................................................... 23

Selecting the units ...............................................................................23

Selecting the shooting modes (scene files)...................................... 24

Types of shooting modes ................................................................... 24

How to select the shooting mode ....................................................... 24

Shooting ............................................................................................... 25

What to do when encountering problems in the basic shooting

operations ........................................................................................ 26

More advanced operations ................................................................. 26

Manual shooting .................................................................................. 27

Manually adjusting the focus.............................................................. 27

Manually adjusting the iris.................................................................. 27

Manually adjusting the shutter speed ................................................ 27

Manually adjusting the gain ............................................................... 27

Preset memories.................................................................................. 27

White balance adjustment .................................................................. 28

Automatic adjustment (AWB: AWB A or AWB B) .............................. 28

Auto tracking white adjustment (ATW)............................................... 28

3200K and 5600K presets ................................................................. 28

VAR.................................................................................................... 28

Black balance adjustment ..................................................................29

Automatic adjustment ........................................................................ 29

Black level (master pedestal) adjustment ......................................... 29

Genlock adjustment ............................................................................ 29

Horizontal phase adjustment ............................................................. 29

Basic setup operations ....................................................................... 30

Operations on the AW-RP50 Remote Camera Controller ................. 31

Operations on the AW-RP120 Remote Camera Controller ............... 33

Operations on the AK-HRP200 Remote Operation Panel ................. 35

Camera menu items ............................................................................38

Setting the camera menu items ......................................................... 38

Top menu (Top Menu) screen ........................................................... 38

Camera screen .................................................................................. 39

Brightness 1/2 screen ........................................................................ 39

Brightness 2/2 screen ........................................................................ 40

Picture 1/4 screen .............................................................................. 41

Picture 2/4 screen .............................................................................. 41

Picture 3/4 screen .............................................................................. 42

Picture 4/4 screen .............................................................................. 42

Matrix 1/5 screen ............................................................................... 43

Matrix 2/5 screen ............................................................................... 43

Matrix 3/5 screen ............................................................................... 44

Matrix 4/5 screen ............................................................................... 44

Matrix 5/5 screen ............................................................................... 45

Intelligent screen ................................................................................ 45

System screen ................................................................................... 46

Genlock screen .................................................................................. 46

Output screen .................................................................................... 47

Others 1/5 screen .............................................................................. 48

Others 2/5 screen .............................................................................. 49

Others 3/5 screen .............................................................................. 49

Others 4/5 screen .............................................................................. 50

Others 5/5 screen .............................................................................. 50

Maintenance screen........................................................................... 51

Firmware VER 1/2 screen .................................................................. 51

Firmware VER 2/2 screen .................................................................. 51

IP Network screen.............................................................................. 52

Hour Meter screen ............................................................................. 53

Camera menu item table ..................................................................... 54

Displaying the web screen .................................................................58

Displaying the web screen using a personal computer...................... 58

Switching between the Live screen [Live] and Web setup screen

[Setup] ........................................................................................... 59

Web screen operations ....................................................................... 60

Live screen [Live] : Single display mode ............................................ 60

Live screen [Live] : Multi display mode .............................................. 64

Web screen configurations ................................................................65

Logging into the Web setup screen [Setup] ....................................... 65

Web setup screen [Setup].................................................................. 65

Basic screen [Basic]........................................................................... 66

Image screen [Image] ........................................................................ 67

Multi screen setup screen [Multi-screen setup].................................. 83

User management screen [User mng.] .............................................. 84

Network setup screen [Network] ........................................................ 86

Maintenance screen [Maintenance] ................................................... 99

Displaying the web screen using a mobile terminal ...................... 102

System log displays .......................................................................... 106

Limiters............................................................................................... 107

Safe mode ..........................................................................................108

Concerning the safe mode ............................................................... 108

Detection of equipment trouble ........................................................ 108

Troubleshooting ................................................................................ 109

Specifications .................................................................................... 118

Index ................................................................................................... 121

Before use

Overview

• This unit is an outdoor compatible full HD camera with an integrated pan-tilt head that features the newly developed 1/2.86-type full HD

3MOS sensor and digital signal processor (DSP).

• In addition to its optical 20× zoom lens, the unit is equipped with

10× digital zoom to achieve vibrant high-quality images that have a horizontal resolution of 1000 lines.

With its high sensitivity and built-in image-shake correction and nightmode functions, the unit can record in a wide range of environments.

• When a controller is connected, camera operations can be performed smoothly via IP control or serial control.

• The unit features a night mode that exposes subjects to infrared rays, making it possible to shoot even under low-light conditions.

• When the unit is connected to a personal computer via an IP network, it can be operated via a web browser.

• Equipped with a newly developed codec engine, the unit can output

Full HD images at up to 60 fps via a network.

• The unit supports standard serial communication formats, allowing connection to commercially available controllers.

• Connection with a Panasonic camera controller is also possible via

Panasonicʼs proprietary serial communication format.

• The unit comes standard with various functions essential for an outdoor shooting environment.

• Intelligent functions (auto adjustment)

• Wiper

• Heater

• Defroster

• Vibration correction function

• Haze reduction function

• Washer control

Computer requirements

CPU Intel

Memory For Windows:

Network function 10BASE-T or 100BASE-TX port × 1

Image display Resolution: 1024 × 768 pixels or more

Supported operating systems and

web browsers

Core™ 2 DUO 2.4 GHz or more

recommended

1 GB or more

(2 GB or more for 64-bit editions of Microsoft®

Windows Microsoft Windows

For Mac:

2 GB or more

Color generation: True Color 24-bit or more

For Windows:

For Mac:

10, Microsoft® Windows® 8.1,

Windows® 8, and Microsoft®

Microsoft Windows® Internet Explorer® 11.0

Microsoft® Windows® 8.1 Pro 64-bit / 32-bit Windows® Internet Explorer® 11.0

Microsoft® Windows® 8 Pro 64-bit / 32-bit Windows® Internet Explorer® 10.0

Microsoft® Windows® 7 Professional SP1

64-bit / 32-bit

Windows® Internet Explorer® 11.0 / 10.0 / 9.0 /

8.0

OS X 10.11 Safari 9.0

OS X 10.10 Safari 8.0.4

OS X 10.9 Safari 7.0.2

OS X 10.8 Safari 6.1.2

Windows® 10 Pro 64-bit / 32-bit

For iPhone, iPad, iPod touch:

iOS Standard web browsers

For Android:

Android OS Standard web browsers

Other Adobe

Use the desktop version of Internet Explorer. (Internet Explorer for

Reader® (for viewing the operating instructions available on the website)

Modern UI is not supported.) Windows® XP compatibility mode is not supported.

The 64-bit version of Internet Explorer® is not supported.

Before use (continued)

IMPORTANT

• Failure to provide the required personal computer

environment may slow down the delineation of the images on the screen, make it impossible for the web browser to work and cause other kinds of problems.

<NOTE>

• Depending on the software version of the unit, an update may be necessary.

• Use the desktop version of Internet Explorer. (Internet Explorer for Modern UI is not supported.)

• For the latest information on compatible operating systems and web browsers, visit the support desk at the following website.

http://pro-av.panasonic.net/

Disclaimer of warranty

IN NO EVENT SHALL Panasonic Corporation BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE

CASES, INCLUDING BUT NOT LIMITED TO BELOW:

A ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION,

DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR

EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;

B PERSONAL INJURY OR ANY DAMAGE CAUSED BY

INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER;

C UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION

OF THE PRODUCT BY THE USER;

D INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES

ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;

E ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE,

OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;

F ANY DEMANDS FOR COMPENSATION, CLAIMS, ETC.

OCCASIONED BY THE INFRINGEMENT OF PRIVACY BY INDIVIDUALS OR ORGANIZATIONS WHOSE IMAGES WERE SHOT BY THE USER BECAUSE THESE IMAGES (INCLUDING THE RECORDINGS MADE) WERE MADE AVAILABLE BY THE USER BECAUSE IN THE PUBLIC DOMAIN FOR SOME REASON OR OTHER OR BECAUSE THE IMAGES ENDED UP BEING USED FOR PURPOSES OTHER THAN THE ONE DESCRIBED ABOVE;

G LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.

Network security

As the unit intended to be used while connected to a network, the following security risks exist.

A Leakage or theft of information through the unit B Unauthorized operation of the unit by persons with malicious intent C Interference with or stoppage of the unit by persons with malicious

intent

It is your responsibility to take precautions, such as those described below, to protect yourself against the above network security risks.

• Use the unit in a network secured by a firewall, etc.

• If the unit is connected to a network that includes personal computers, make sure that the system is not infected by computer viruses or other malicious programs (using a regularly updated antivirus program, antispyware program, etc.).

• Protect your network against unauthorized access by restricting users to those who log in with an authorized user name and password.

• After accessing the unit as an administrator, be sure to close all web browsers.

• Change the administrator password periodically.

• Restrict access to the unit by authenticating the users, for example, to prevent setting information stored on the unit from leaking over the network.

• Do not install the unit in locations where the unit, cables, and other parts can be easily damaged or destroyed by persons with malicious intent.

• Avoid connections that use public lines.

<NOTE>

Notes on user authentication

• User authentication on the unit can performed via digest authentication or basic authentication. If basic authentication is used without the use of a dedicated authentication device, password leaks may occur. We recommend using digest authentication or host authentication.

Usage restrictions

• We recommend connecting the unit, controller, and any computers to the same network segment. Events based on settings inherent to the network devices, for example, may occur in connections that include different segments, so be sure to perform checks prior to operation.

Features

Multi-format support



• You can switch between the following formats via the camera

menus or a web browser.

Supported formats:

1080/59.94p, 1080/29.97p 1080/29.97PsF 1080/25p

Native output

Over 59.94i output

For 1080/25PsF, 50i may be displayed on the monitor screen.

Furthermore, for 1080/23.98PsF and 29.97PsF, 59.94i may be

displayed on the monitor screen.

1/2.86-type MOS sensor and high-performance



, 1080/23.98PsF

, 1080/50i, 1080/25PsF

, 1080/23.98p

, 1080/59.94i,

, 720/59.94p, 1080/50p,

, 720/50p

20x zoom lens featured

• A newly developed 1/2.86-type full HD 3MOS sensor and DSP (digital signal processor) are incorporated. High-quality pictures

are obtained by video processing in many different kinds of ways.

• In addition to its optical 20x zoom lens, the unit comes with a 10x digital zoom to achieve high-quality images that overflow with ambiance.

• A dynamic range stretcher (DRS) function that compensates for overexposure and loss of dark detail and a digital noise reduction (DNR) function for minimizing image lag even in dark locations and shooting scenes clearly are incorporated to reproduce clean and clear images in a wide range of applications.

Easy operation of unit enabled by its



integration with a high-performance pan-tilt

head unit

• Operations at the high speed of 60°/s

• Wide rotational angles with a panning range of ±175° and a tilting

range from –30° to 210°

• Storage of up to 100 positions in the preset memory (The number of preset memories that can be used varies from one controller to another.)

Built-in night mode



• The unit supports infrared shooting. By exposing subjects to infrared rays, shooting under ordinarily difficult low-light conditions is possible. (Image output will be in black and white.)

• The iris will be fixed at open.

IP image output functions



• The unit is equipped with image compression and IP transmission

LSI capabilities. Output in Full HD quality at up to 60 fps.

• Operation with IP control allows for a wide range of applications, such as controlling the camera from remote locations.

Standard serial communication support



• Connect to a commercially available controller via RS-422 interface.

<NOTE>

• With the standard serial communication formats, control related to outdoor functions cannot be performed directly with the controller. Perform the control by setting the camera menu.

High degree of compatibility with Panasonic’s



currently available controllers, enabling a flexible system to be put together

• A maximum of five units can be operated by serial control from

one of Panasonic’s currently available controllers (AW-RP50, AW-RP120 and AK-HRP200).

The unit can also be used together with the cameras and pan-tilt head unit systems currently available from Panasonic Corporation so that an existing system can be used to advantage to put together a system that is even more flexible.

<NOTE>

• It may be necessary to upgrade the version of the controller in order to support the unit. For details on upgrading, visit the support page on the following website. http://pro-av.panasonic.net/ The maximum distances between the units and controller is 1000 meters (3280 ft). (when serial control is exercised) Use of an external device or some other means must be provided separately in order to extend the video signal connections.

Easy construction of systems thanks to



integrated design used for outdoor housing, pan-tilt head, camera, and lens

• The construction of systems has been made easier by integrating the outdoor compatible housing, camera, lens, and pan-tilt head into a single unit.

Flexible camera layout enabled by simple



connection

• IP control allows outstanding connectivity.

<NOTE>

• This unit is a stand-alone (desktop) device with support for

outdoor use. Please note that it cannot be used in a vehicle.

More functionality than the indoor-only model



• The functions required for shooting outdoors have been included

in addition to the functions of the indoor-only model (AW-HE130)

which have a proven track record.

Easy connections and settings courtesy of IP



control

• Up to a hundred units can be operated by IP connection from a

Panasonic controller (AW-RP50, AW-RP120, AK-HRP200). (The maximum length of the LAN cables is 100 meters (328 ft).)

PoE++



eliminates need for camera power

configurations

• Configurations for camera’s power supply are not necessary when

the unit is connected to a network device that supports the PoE++ standard (IEEE802.3bt Draft ver.2.0 compliant)

<NOTE>

• When using a PoE++ device that requires software authentication, it may take a few minutes after power supply starts before the unit is operational.

• If the external DC power supply and a PoE++ power supply are connected simultaneously, the external DC power supply will have priority. If the external DC power supply is disconnected while both power supplies are connected, the unit will restart automatically, and the image will be interrupted.

• Use a Category 5e cable or higher when using a PoE++ power supply. The maximum length of the cable between the power

supply unit and the unit is 100 meters (328 ft). Using a cable that

is lower than Category 5 may result in reduced power supply capabilities.

• When a PoE++ injector is connected to a personal computer that supports Gigabit Ethernet using a straight LAN cable, the personal computer may not recognize the injector in rare cases. In such cases, connect the personal computer to the unit using a cross LAN cable (via cross connection).

Power over Ethernet Plus Plus. Referred to as “PoE++ˮ in this

manual.

For details on PoE++ devices for which operation has been

verified, consult your local dealer or Panasonic representative.

Controller supported

 AW-RP50  AW-RP120  AK-HRP200

• It may be necessary to upgrade the version of the controller in order to support the unit. For details on upgrading, visit the support page on the following website. http://pro-av.panasonic.net/

<NOTE>

• The following operations can not be performed via the following controllers.

Camera OSD menu operation Supported Supported

Scene

Iris Mode Supported Supported

Shutter Mode

Gain Supported ND Filter Not supported Not supported Day/Night Supported with some restrictions

White Balance Mode

AWB/ABB Supported Supported Color Temperature Not supported Not supported R Gain / B Gain Not supported Supported Pedestal Not supported Supported R Pedestal / B Pedestal Not supported Supported with some restrictions Detail Not supported Not supported V Detail Level Not supported Not supported CAM/BAR Supported Pan Supported Supported Tilt Supported Supported Preset Supported Supported Preset Speed Not supported Not supported Preset Speed Table Not supported Not supported Preset Scope Not supported Not supported Freeze During Preset Not supported Not supported Focus Mode Supported with some restrictions Zoom Supported Supported Digital Extender Not supported Not supported OIS/D.I.S.S. Not supported Not supported Tally Supported with some restrictions

If the setting value is changed on another device, it may take some time for the setting value to be applied.

If the Shutter Mode is not turned off/on after configuration, the value will not be changed.

Improper operation will occur when Gain is set to 19 dB or higher.

If the setting value is changed on another device, the setting value will not be applied. (If the value is configured locally on the device, the value will

be applied.)

The value range display will be incorrect (–150 to +150).

Although the unit is not equipped with a tally lamp, the “OSD Off With Tally” function can be used.

Item AW-RP555 AW-RP655

Supported (1/2/3/USER)

Supported with some restrictions

(Step only)

Supported

(AWB A/AWB B/ATW only)

(HALOGEN/FLUORESCENT/OUTDOOR/USER)

Supported with some restrictions

Supported

Not supported

Supported

(AWB A/AWB B/ATW only)

Supported

Functions that cannot be controlled with the standard protocol



Operations for the following items cannot be controlled with the standard protocol.

Heater Control not possible Wiper Control not possible Defroster Control not possible Washer Control not possible OIS/D.I.S.S. Setting not possible Audio Setting not possible DC Out Control not possible Tally Display function not available on unit

Item Standard protocol incompatibility

Accessories

Check that the following accessories are present and accounted for.

• After removing the product from its container, dispose of the packing materials in an appropriate manner.

Hexagonal bolt M8 × 30 mm (4) M8 washer (4) M8 spring washer (4)

Cable cover (1) Washer nozzle mount bracket

(1)

Drop-prevention wire (1) Drop-prevention wire

mounting screw (with hexagonal socket, for unit)

M4 × 10 mm (1)

Operating precautions

Shoot under the proper lighting conditions.



To produce pictures with eye-pleasing colors, shoot under the proper lighting conditions. The pictures may not appear with their proper colors when shooting under fluorescent lights. Select the proper lighting as required.

To ensure a stable performance in the long



term

Using the unit for prolonged periods in locations where the temperature and humidity levels are high will cause its parts to deteriorate, resulting in a reduction of its service life.

(Recommended temperature: Max. 35 °C (95 °F))

Ensure that a cooling unit or heating unit will not blow any air directly toward the installation location.

Do not point the camera at



Bright subject

strong lights.

When parts of the MOS sensor are exposed to spotlights or other strong lights, blooming (a phenomenon where the edges of strong lights become blurred) may occur.

Blooming

What happens with high-brightness subjects



Flare may occur if an extremely bright light source is pointed at the lens. In a case like this, change the angle or take some other remedial action.

When using the automatic functions



• The initial settings have been set to auto for some of the items of the scenes on the camera menus and other menus, making it impossible for these items to be operated manually. To operate them manually, switch from the auto settings to the manual settings as required.

• In some situations, it may be hard to focus at the auto setting. In cases like this, select the manual setting, and focus manually.

Zooming and focusing



When the focus is set manually, out-of-focusing may occur during zooming. After zooming, if necessary, either adjust the focus or set the focus to auto. When using the focus at the manual setting, proceed with zooming after setting the focus position at the Tele end where the focusing

accuracy is higher. (However, if the distance from the unit to the

subject is less than 1.5 meters (4.92 ft), the subject may shift out of focus at the Wide end.) If zooming is performed to the Tele end after having adjusted the focus at the Wide end, out-of-focusing may occur.

About the pan/tilt operation and lens operation



when the power is turned on

When the unit’s power is turned on, the pan/tilt mechanism and the zoom, focus, and iris of the lens are adjusted automatically.

The unit comes with the safe mode.



The safe mode is function designed to protect the unit from damage.

For further details, refer to “Concerning the safe mode” (→ page 108).

Operating temperature range



Avoid using the unit in cold locations where the temperature drops

below –15 °C (5 °F) or hot locations where the temperature rises above 45 °C (113 °F) since these temperatures downgrade the

picture quality and adversely affect the internal parts.

Color bars



Color bars are used to adjust the color phase, and the widths and positions of these bars may differ from other models.

Concerning the IP video frame rates



The IP video frame rate may be slower depending on the network environment, performance of your personal computer or mobile terminal, subject of the video, and access volume.

H.264 patent pool licensing



This product is licensed based on the AVC Patent Portfolio License, and the license does not extend beyond uses by users, who engage in the acts described below, for their own personal and non-profit applications. (i) Recording of image information in compliance with the AVC

standard (hereafter, “AVC videos”)

(ii) Playing of AVC videos recorded by consumers engaging

in personal activities or AVC videos acquired from licensed providers

For details, visit MPEG LA, LLC website (http://www.mpegla.com).

Concerning PoE++ power supply



The unit complies with the IEEE802.3bt Draft ver.2.0 standard. Use a compatible Ethernet hub and PoE++ injector to use a PoE++

power supply.

For details on Ethernet hubs and PoE++ injectors for which

operations have been verified, consult your local dealer.

Turn off the power before connecting or



disconnecting the cables.

This unit is not equipped with a power switch.

Turn off the DC power supply or PoE++ power supply device before

connecting or disconnecting cables.

Handle the unit carefully.



Do not drop the unit or subject it to strong impact or vibration. Failure to obey may cause the unit to malfunction.

When the unit is not in use



Turn off the unit’s power when it is not in use. When the unit is no longer going to be used, do not leave it lying around, but be absolutely sure to dispose of it properly.

Operating precautions (continued)

Do not touch the optical system parts.



The optical system parts are vital to the operation of the camera. Under no circumstances must they be touched. In the unlikely event that they have become dusty, remove the dust by using a camera blower or by wiping them gently with a lens cleaning paper. Do not touch the glass surface or its screws when using the defroster. As the defroster heats the glass surface, it can become very hot.

Do not point the camera directly at the sun or a



laser beam no matter whether it is turned on or not.

Taking images of the sun, laser beams, or other brightly lit subjects for prolonged periods of time may damage the CCD.

Personal computer used



If the same image is displayed for a prolonged period on a personal computer’s monitor, the monitor may be damaged. Use of a screen saver is recommended.

Concerning the IP address setting



Do not run the Easy IP Setup Software on a multiple number of personal computers for a single camera and set the IP address at the same time. Otherwise, you will be unable to complete the proper procedure and set the IP address correctly.

Do not allow foreign matter to make contact



with the rotating parts.

Failure to obey may cause the unit to malfunction.

Do not turn the camera head by hand.



Turning the camera head by hand may cause the unit to malfunction.

Use the unit in an environment with minimal



moisture and dust.

Avoid using the unit in an environment with high concentration of moisture or dust since these conditions will damage the internal parts.

About the dehumidifying element



The unit incorporates a dehumidifying element to maintain a low humidity level inside the camera. Condensation may form and dehumidification may take a while depending on conditions such as the temperature, humidity, and weather.

About cleaning the front glass



If the front glass becomes dirty, remove the dirt with lens cleaning paper (paper used to clean cameras and glasses) or the like. The front glass may be scratched if sand, etc. is adhered to it during cleaning. If the lens is very dirty, we recommend washing it with water. Do not touch the glass surface or its screws when using the defroster. As the defroster heats the glass surface, it can become very hot.

About the lens/pan-tilt head



If the lens, pan-tilt head, and other parts are not operated for a long period of time, the viscosity of the grease applied inside them may increase and operation may become no longer possible. Move the lens and pan/tilt head regularly.

Do not get close to the moving parts of the



camera head.

Do not put your fingers or body close to the unit while it is in operation. Doing so may result in injury or cause the unit to malfunction. Furthermore, if the unit hits a person or obstacle, during the panning or tilting operation, the unit will enter into the safe mode.

For further details, refer to page 108.

About the camera head



Snow, water, dust, etc. may accumulate on the hood of the lens. Move the camera head regularly so that snow, water, dust, etc. do not accumulate on the hood.

Maintenance



Turn off the unit’s power before proceeding with maintenance. Failure to obey may result in injuries. Wipe the surfaces using a soft dry cloth. Avoid all contact with benzine, paint thinners and other volatile substances, and avoid using these substances. Otherwise, the body may become discolored.

About consumables



The following parts are consumables. Replace them using the lifespans as a guide. The lifespans may vary depending on the operating environment and operating conditions.

The lifespans are a guide for when the unit is used at 35 °C (95 °F).

• Cooling fan: Approx. 20000 hours

• Wiper: Operated approx. 120000 times; guide for replacement:

Approx. 2 years

• Wiper rubber: Average of 5000 hours operation; guide for

replacement: Approx. 2 years

Contact your dealer regarding replacements.

Disposal of the unit



When the unit has reached the end of its service life and is to be disposed of, ask a qualified contractor to dispose of the unit properly in order to protect the environment.

Information on software used with this product



This product includes GNU General Public License (GPL) and GNU Lesser General Public License (LGPL) licensed software, and the customer is entitled to obtain, modify, or redistribute the source code for the software. This product includes MIT Licensed software. This product includes BSD Licensed software. For details on obtaining the source codes, visit the following website. http://pro-av.panasonic.net/

However, do not contact Panasonic for questions regarding obtained source codes.

9 9

Parts and their functions

6. RS-422 connector <RS-422>

This RS-422 connector (RJ45) is connected when exercising serial

control over the unit from an external device. Use a cable with the following specifications for the connection to this connector.

LAN cable

(3280 ft)

(category 5 or above, straight cable), max. 1000 m

Use of an STP (shielded twisted pair) cable is recommended.

No.

Signal

1 GND 5 TXD+ 2 TALLY 6 RXD+ 3 RXD– 7 — 4 TXD– 8 —

No.

Signal

<NOTE>

• Although the unit is not equipped with a tally lamp, “OSD Off With

Tally” function can be used when pin 1 (GND) and pin 2 (TALLY

signal) are shorted.

• Do not apply voltage to pin 2 (TALLY signal), as it is a contact input.

7. LAN connector for IP control <LINK/ACT>

This LAN connector (RJ45) is connected when exercising IP control

over the unit from an external device. Use a cable with the following specifications for the connection to this connector.

Rear panel

9 9

816

When using a PoE++ Ethernet hub

LAN cable

max. 100 m (328 ft)

When not using a PoE++ Ethernet hub

LAN cable

max. 100 m (328 ft)

Use of an STP (shielded twisted pair) cable is recommended.

<NOTE>

• When connecting directly to a controller without an Ethernet hub, use a cross cable.

1210

(category 5e or above, straight cable),

(category 5 or above, straight cable),

8. G/L IN connector <G/L IN>

RS-422

12V IN

ACT LINK

POWER/

10BASE-T/

STANDBY

100BASE-TX

6 7

11 13 14 15

AUDIO IN(1/2)

SDI OUT

1/PM 2G/L IN

MODE

EXT

SIGNAL GND

PUSH

1. Drop-prevention wire attachment hole

Use the screw provided to fix the drop-prevention wire.

2. Hole for securing the camera pedestal

Four places in the camera pedestal.

3. Camera head

This rotates in the up and down direction.

4. Pan head

This rotates in the right and left direction.

5. Wiper

Moves left and right to clear the lens.

This is the external sync signal input connector. Supply to this connector the signals that correspond to the video signal format which has been set.

Format

1080/59.94p 1080/29.97p 1080/23.98p 1080/59.94i 1080/29.97PsF 1080/23.98PsF 720/59.94p

1080/50p 1080/25p 1080/50i 1080/25PsF 720/50p

External sync signal input format

BBS Tri-level sync

480/59.94i 480/59.94i 480/59.94i 480/59.94i 480/59.94i ― 480/59.94i

576/50i 576/50i 576/50i 576/50i 576/50i

1080/59.94i

—

1080/59.94i 1080/59.94i 1080/59.94i 1080/23.98PsF 720/59.94p

1080/50i

—

1080/50i 1080/50i 720/50p

<NOTE>

• Locking to a subcarrier is not possible with BBS.

9. Hole used to secure cable cover

Use screws to secure the cable cover.

10. SDI OUT connector <SDI OUT 1/PM, SDI OUT 2>

This is the SDI video signal output connector.

• OSD output from the SDI OUT 1/PM connector is possible, so you can display the camera menu and status on the monitor.

Parts and their functions (continued)

11. DC IN connector <12V IN> (XLR connector)

Input 10.8 V (12 V–10%) to 24 V (21.8 V+10%) DC.

<NOTE>

• Use a DC cable with the following lengths.

For 12 V input: Max. 3 m (9.84 ft) (when using an AWG16 cable) For 21.8 V input: Max. 20 m (65.62 ft) (when using an AWG16

cable)

 External DC power supply

Connect after making sure that the output voltage of the external DC power supply is compatible with the rated voltage of the camera. Select an output amperage for the external DC power supply with a margin above the total amperage of the connected devices. The total amperage of connected devices can be calculated with the following formula.

Total power consumption ÷ voltage

When the power of the camera is turned on, inrush current is generated. Insufficient power supply when turning on the power may cause a malfunction. We recommend that you use an external DC power supply that can assure double the capacity of the total power consumption of the camera and connected devices that are turned on by interlock when the power of the camera is turned on (such as lenses, wireless microphone receivers).

• Make sure of the pin alignment of the DC output terminal of the external DC power supply and the camera DC IN connector, and connect the polarity correctly.

If the +12 V power supply is mistakenly connected to the GND terminal,

it may cause fire or malfunction.

12V IN

1 GND

2 —

3 —

4 +12V

HA16RA-4P (77)

Hirose Electric Co.

12. MODE switches <MODE>

Switch

positions

AW series protocol setting (Factory settings)

Standard protocol setting (baud rate 38400 bps)

Function

16. Status display lamp <POWER/STANDBY>

This lights in the following way depending on the status of the unit.

Orange: When the standby status is established Green: When the power is on Red: When trouble has occurred in the unit

Output conditions for each video format



 SDI output

Format SDI output

HD/SDI 1080/59.94p

1080/50p

1080/59.94i

1080/50i

1080/29.97PsF

1080/25PsF

1080/23.98PsF

1080/29.97p

1080/25p

1080/23.98p

720/59.94p

720/50p

Native output

Over 59.94i output

For 1080/25PsF, 50i may be displayed on the monitor screen.



Furthermore, for 1080/23.98PsF and 29.97PsF, 59.94i may be

displayed on the monitor screen.

 IP video transmission output (1-/multi-channel display)

1-channel display

Resolution 1920×1080/1280×720/640×360/320×180/160×90

Frame

59.94 Hz 1 fps/2 fps/3 fps/5 fps/6 fps/10 fps/15 fps/30 fps/

rate

50 Hz

60 fps only during H.264 transmission and 1920×1080 or 1280×720

resolution

50 fps only during H.264 transmission and 1920×1080 or 1280×720

resolution

(non-dependent on SYS format)

60 fps

1 fps/2 fps/5 fps/10 fps/12.5 fps/25 fps/50 fps

Standard protocol setting (baud rate 9600 bps)

These are the positions for maintenance. Do not use the unit while the switches are in these positions.

13. AUDIO IN connector <AUDIO IN(1/2)>

Inputs external audio (line). When connecting a microphone or other devices with different levels, match the level using an amp, for example.

14. Ground connector <SIGNAL GND>

Connects to the ground connector on a wall outlet, ground bar, etc.

for grounding. (→ page 5)

15. EXT connector <EXT>

This is the washer control and 12 V DC output connector.

<NOTE>

• Keep outputs for pin number 4 [12V-OUT] within 12 V/0.5 A DC.

• The maximum cable length for connections to pin number 4

[12V-OUT] is 0.5 m (1.64 ft) when using an AWG24 cable.

Use a thicker cable when a greater length is required.

Pin No. Signal Pin No. Signal

1 DC GND 3 COLD 2 HOT 4 12V-OUT

Multi-channel display

Setting H.264 CH1 H.264 CH2 H.264

Resolution 1920×1080

Frame

59.94 Hz 60 fps 5 fps

rate

50 Hz 50 fps 5 fps

Different resolutions must be specified for JPEG CH1/CH2/CH3.

1280×720

1920×1080

1280×720

640×360 320×180

160×90

15 fps

30 fps

12.5 fps 25 fps

CH3/CH4

1280×720

640×360 320×180

160×90

5 fps

15 fps

30 fps

5 fps

12.5 fps 25 fps

JPEG

CH1/CH2/

CH3

1920×1080

1280×720

640×360 320×180

160×90

1 fps 2 fps 3 fps 5 fps

6 fps

10 fps

15 fps

30 fps

1 fps 2 fps 5 fps

10 fps

12.5 fps 25 fps

AW-RP50 (not supplied)













For detailed operations, refer to the Operating Instructions of the AW-RP50 — <Operations and Settings>.

Control panel













  

POWER ALARM F1 CAMERA

1 2 3

GAIN/PED

PAGEMENU F2 EXIT

DELETESTORE

R/B GAIN R/B PED

6 7 8 9 10

DETAIL

SCENE/MODE

PRESET MEMORY / MENU

1 2 3 4 5

CAMERA STATUS / SELECTION

AWB/ABB4SHUTTER

SYSTEMSETUPCAMERA



OSD

USER2USER1

PT ACTIVEAUTOIRIS



TELE

ZOOM

WIDE

AUTO

1 POWER indicator [POWER]

This indicator lights when the POWER switch () on the rear panel

is set to ON while power is supplied to the DC IN socket.

2 ALARM indicator [ALARM]

This indicator lights when there is a problem with the power supply

(voltage drop).

It also lights when an alarm (a cooling fan alarm or pan/tilt error) has

been received from a remote camera.

When the alarm indicator has lighted, stop using the unit

immediately, and be absolutely sure to contact your dealer.

Continuing to use the AW-RP50 even after an alarm has occurred may cause the AW-RP50 to malfunction.

The alarm information can be output to an external device from the

unit’s TALLY/GPI connector ().

3 LCD panel

The current setting statuses are displayed on this panel.

4 F1 dial, F2 dial [F1, F2]

These dials are turned to change the menu values, and they are

pressed to enter the changes that have been made.

The F1 dial is used to operate the items displayed at the top of the

LCD panel, and the F2 dial is used to operate the items displayed

underneath.

What appears on the on-screen displays of the remote cameras and

how operations are performed differ depending on the camera type.

5 CAMERA OSD button [CAMERA OSD]

When the CAMERA OSD button is held down, its indicator lights, and

the on-screen menu of the selected remote camera is displayed as

the output image of the remote camera.

When the button is held down again while its indicator is lighted, the

menu is cleared, and the indicator goes off.

6 EXIT button [EXIT]

Press this during menu operations to return to the previous

hierarchical level.

PTZ/FOCUS SPEED PAN/TILTFOCUS/PUSH OTAF

HILOW

7 USER buttons [USER1, USER2]

The functions of some of the setting items on the menus can be

assigned to [USER1] and [USER2] to be recalled later.

 Assignable functions:

Super Gain, Haze Reduction, Fan, Heater, Defroster, Wiper,

Washer

 For the [Wiper] function, press PRESET MEMORY/MENU

buttons 1 to 3 (1: Off, 2: Slow, 3: Fast) after pressing the USER

button.

8 MENU button [MENU]

Press this to recall the menus using the PRESET MEMORY/MENU

buttons ().

When it is pressed again while its indicator is lighted, the menu is

cleared, and the indicator goes off.

Button indicator ON:

The menu operations take effect.

Button indicator OFF:

The menu operations have no effect.

Refer to “Basic operations for the menus”.

9 PAGE button [PAGE]

Press this to specify the preset memory of the remote camera.

When the button is pressed, its indicator lights, and the mode for

selecting the page of the preset memory is established.

In this mode, press one of the PRESET MEMORY/MENU buttons

(), and specify the page number.

Next, specify the number on the page using one of the PRESET

MEMORY/MENU buttons.

 STORE button [STORE]

Press this to register the preset memory data of the currently

selected remote camera.

When it is pressed again while its indicator is lighted, the menu is

cleared, and the indicator goes off.

Button indicator ON:

The preset memory data registration mode is established.

Button indicator OFF:

The preset memory data registration mode is released.

AW-RP50 (not supplied) (continued)

 DELETE button [DELETE]

Press this to delete the preset memory data for the currently selected

remote camera.

When it is pressed again while its indicator is lighted, the menu is

cleared, and the indicator goes off.

Button indicator ON:

The preset memory data deletion mode is established.

Button indicator OFF:

The preset memory data deletion mode is released.

 PRESET MEMORY/MENU buttons

[PRESET MEMORY/MENU]

Use these buttons to recall the preset memory data and recall

menus.

 CAMERA STATUS/SELECTION buttons

[CAMERA STATUS/SELECTION]

Use these buttons to select up to five remote cameras.

Button indicator ON:

The corresponding remote camera is selected.

Button indicator OFF:

The selection of the corresponding remote camera is

released.

Using the menu, up to 100 remote cameras can be divided into 1 to 20 groups, and then registered and controlled.

The statuses of the remote cameras assigned to buttons 1 to 5 can

be identified using the indicators positioned above the buttons.

 ZOOM button [ZOOM]

Use this to adjust the lens zoom.

When the TELE end is pressed:

Telephoto setting

When the WIDE end is pressed:

Wide-angle setting

The zooming speed changes depending on the extent to which the

button is pressed.

 Auto focus button [AUTO]

Press this to control the focus automatically.

Button indicator ON:

Auto focusing

Button indicator OFF:

Manual focusing During auto focusing, operating the FOCUS/PUSH OTAF dial ()

will have no effect.

 This function works when an auto focus function is provided in

the remote cameras.

If the auto focus function is not provided, operate the focus

manually (in which case the button indicator will be OFF).

 When using a lens equipped with an extender function for the

remote camera, the extender function can also be switched

between ON and OFF by pressing the auto focus button.

Button indicator ON:

The extender function is enabled.

Button indicator OFF:

The extender function is disabled.

(For details on how to connect the lens control cables to the pan-

tilt head, refer to the Operating Instructions of the pan-tilt head.)

 FOCUS/PUSH OTAF dial [FOCUS/PUSH OTAF]

Use this to control the focus manually.

When it is turned clockwise:

The focusing moves to the far end.

When it is turned counterclockwise:

The focusing moves to the near end.

When the dial is pressed, auto focusing is initiated temporarily, and

the subject being shot is brought into focus. (OTAF) During auto focusing (while the indicator of the auto focus button ()

is lighted), operating this dial will have no effect.

OTAF: one-touch auto focus

 IRIS dial [IRIS]

Use this dial to control the lens iris manually.

When it is turned clockwise:

The lens iris opens more and more.

When it is turned counterclockwise:

The lens iris closes more and more.

When it is held down:

The lens iris closes.

 Auto iris button [AUTO]

Press this to control the lens iris automatically.

Button indicator ON:

Auto iris

Button indicator OFF:

Manual iris

 PAN/TILT lever [PAN/TILT]

Use this lever to control the direction of the remote cameras.

When it is leaned toward the left or right:

The cameras move to the left or right.

When it is leaned toward you or away from you:

The cameras move up or down.

The movement speed differs depending on the angle to which the

lever is moved.

 PTZ/FOCUS SPEED dial

[PTZ/FOCUS SPEED]

Use this dial to adjust the speed at which the operations (pan, tilt,

zoom, focus) of the remote cameras are controlled.

When it is turned clockwise:

Operation at a higher speed

When it is turned counterclockwise:

Operation at a lower speed

 PT ACTIVE button [PT ACTIVE]

Hold down this to switch between enabling and disabling the PAN/

TILT lever operations.

Button indicator ON or blinking:

The PAN/TILT lever operations take effect.

Button indicator OFF:

The PAN/TILT lever operations have no effect.

 When [P/T/Z/F] has been set by menu operations ([SETUP]

menu > [OPERATE] > [PT ACTIVE] item), operation enabling

and disabling are switched not only for the PAN/TILT lever but for

the ZOOM button, auto focus button and FOCUS/PUSH OTAF

dial as well.

 When the PT ACTIVE button indicator is blinking, the PAN/TILT

lever and ZOOM button can be used to control the parameters of

the switcher.

 When “Button Select” has been selected by menu operations

([SETUP] menu > [SW LINK] > [P/T LEVER] item), the control

applications of the PAN/TILT lever and ZOOM button can be

switched.











AW-RP50 (not supplied) (continued)

Rear panel



 

SIGNAL GND

TO PAN/TILT HEAD

TALLY/GPI

5 4 3 2 1

 POWER switch [POWER]

When the POWER switch is set to the ON position, the POWER indicator (1) lights, and the unit can be operated.

 TO PAN/TILT HEAD 1 to 5 connectors

[TO PAN/TILT HEAD 1 to 5] (RJ-45)

Connect the remote cameras to these connectors using straight

cables (category 5 or above).

 LAN connector [LAN] (RJ-45)

(10BASE-T/100BASE-TX)

Connect the remote camera, switcher or host computer that supports

IP connections to this connector using a LAN cable.

When directly connecting a device to the AW-RP50, use a crossover

cable (category 5 or above).

When making the connection through a hub (switching hub) or other

device, use a straight cable (category 5 or above).

LAN

BOOT

POWER

12V IN

 TALLY/GPI input/output connector [TALLY/GPI]

(D-sub 15-pin, female, inch thread)

 DC IN socket [12V

The AC adaptor provided with the unit is connected to this socket.

IN] (DC 12 V)

 Ground terminal [SIGNAL GND]

Connect this to the system’s ground.

 SERVICE switch [SV/NM]

This switch is used for maintenance purposes.

Normally, it is set at the “NM” position.

 Wire fastening fitting

An anti-theft wire available on the market can be fastened to this

fitting to prevent theft.

AW-RP50 (not supplied) (continued)

Basic operations of the AW-RP50



For detailed operations, refer to the Operating Instructions of the AW-RP50 — <Operations and Settings>.

1, 7

POWER ALARM F1 CAMERA

1 2 3

R/B GAIN R/B PED

GAIN/PED

PAGEMENU F2 EXIT

6 7 8 9 10

DETAIL

DELETESTORE

SCENE/MODE

PRESET MEMORY / MENU

AWB/ABB4SHUTTER

SYSTEMSETUPCAMERA

OSD

USER2USER1

TELE

ZOOM

WIDE

1 2 3 4 5

CAMERA STATUS / SELECTION

AUTO

1. Turn on the AW-RP50’s power.

Set the POWER switch to the ON position.

Power is now supplied to the AW-RP50, and the POWER indicator

lights.

 However, when [CAMERA] > [POWER] > AUTO ON item

have been selected and “On” is selected as the AUTO ON item

setting, power-on is automatically instructed for the remote cameras controlled by the [SYSTEM] > CAM IP ADR item.

2. Select the remote cameras.

Select the remote cameras to be controlled using the CAMERA

STATUS/SELECTION buttons.

3. Adjust the direction in which the remote cameras are to

be pointed.

Use the PAN/TILT lever to adjust the direction in which the remote

cameras are to be pointed.

PT ACTIVEAUTOIRIS

HILOW

PTZ/FOCUS SPEED PAN/TILTFOCUS/PUSH OTAF

6. Adjust the focus.

Turn the FOCUS/PUSH OTAF dial, and adjust the lens focus.

When the dial is pressed during manual focusing, the auto focus

mode is established temporarily, and the subject is brought into

focus automatically.

 The OTAF (one-touch auto focus) takes effect for remote

cameras which are equipped with the OTAF function.

7. Turn off the AW-RP50’s power.

Set the POWER switch to the OFF position.

The AW-RP50’s power is turned off, and the POWER indicator

goes off.

 Even when the AW-RP50’s power is turned off, the power of the

connected remote cameras does not go off.

4. Adjust the zoom.

Use the ZOOM button to adjust the lens zoom.

When the TELE side is pressed, the zoom is set to the telephoto

mode; when the WIDE side is pressed, it is set to the wide-angle

mode.

5. Adjust the lens iris.

Use the IRIS dial to adjust the lens iris.

 While the lens iris is being adjusted, a level meter is displayed

on the LCD panel. (What is displayed by the level meter is an

approximate value.)

IRIS

-----+------

<NOTE>

When performing adjustments for one remote camera from a

multiple number of AW-RP50 remote camera controllers, the

level meter may not show the correct displays.

AW-RP50 (not supplied) (continued)

Basic operations for the menus



For detailed operations, refer to the Operating Instructions of the AW-RP50 — <Operations and Settings>.

POWER ALARM F1 CAMERA

1 2 3

R/B GAIN R/B PED

GAIN/PED

PAGEMENU F2 EXIT

6 7 8 9 10

DETAIL

DELETESTORE

SCENE/MODE

PRESET MEMORY / MENU

AWB/ABB4SHUTTER

SYSTEMSETUPCAMERA

OSD

USER2USER1

1 2 3 4 5

TELE

ZOOM

AUTO

WIDE

1. Set the MENU button to ON.

Press the MENU button and light its indicator.

2. Select the target menu.

Press the corresponding PRESET MEMORY/MENU button, and

light its indicator.

The selected menu is displayed on the LCD panel.

3. Change the settings using the F1 dial and F2 dial.

Use the F1 dial and F2 dial to select the menus and change the

settings.

Use the F1 dial for operations involving the items displayed on the

top line of the LCD panel.

Use the F2 dial for operations involving the items displayed on the

bottom line of the LCD panel.

CAMERA STATUS / SELECTION

PTZ/FOCUS SPEED PAN/TILTFOCUS/PUSH OTAF

PT ACTIVEAUTOIRIS

HILOW

 Press the EXIT button to return the menu to its previous

hierarchical level.

 When the down arrow “” is displayed for a setting item, it means

that the value shown will be entered and the setting reflected when

the F1 dial or F2 dial is pressed.

1.GROUP SELECT 1

 When the down arrow “” is not displayed for a setting item,

it means that the value shown will be entered and the setting

reflected when the F1 dial or F2 dial is turned.

R GAIN : ±0 B GAIN : ±0

F1 dial

F2 dial

Network settings

Use the Easy IP Setup Software to establish the unit’s settings

The settings related to the unit’s network can be established using the Easy IP Setup Software.

You can obtain Easy IP Setup Software (EasyIPSetup.exe) by

downloading it from the following website.

http://pro-av.panasonic.net/

To establish the settings for a multiple number of units, the settings must be selected for each camera involved. If the settings cannot be established using the Easy IP Setup Software, select the settings separately for the unit and personal computer on the

Network setup screen [Network] of the setting menu. (→ page 86)

<NOTE>

• If, after the network settings have been established, another device in the same network has the same IP address, the network operations will not be performed properly. Set the IP address in such a way that it does not duplicate an existing IP address.

• Do not establish network settings from a multiple number of Easy IP Setup Software programs at the same time for a single camera.

Similarly, do not perform the “Auto IP setting” operation of the AW-RP50 remote camera controller at the same time.

The IP address settings may no longer be recognized as a result.

• The Easy IP Setup Software cannot be used from a different subnet via a router.

• The unit cannot be displayed or its settings established using an older version of the Easy IP Setup Software (version older than

Ver 4.25R00).

1. Start the Easy IP Setup Software.

2. Click the [Search] button.

3. Click the MAC address/IPv4 address of the camera to be

set, and click the [Network Settings] button.

<NOTE>

• When a DHCP server is being used, the IP address allocated to the

unit can be checked by clicking the [Search] button of the Easy IP Setup Software.

• If the same IP address is used for any additional cameras, the numbers of the additional cameras will be displayed in the [IPv4 overlap] column of the cameras concerned.

• When the [Access Camera] button is clicked, the Live screen of the selected camera is displayed.

• This unit does not support an IPv4/IPv6 switching function.

4. Input the network items, and click the [Save] button.

<NOTE>

• When a DHCP server is being used, [DNS] of the Easy IP Setup Software can be set to [Auto].

• After the [Save] button is clicked, it takes about 2 minutes for the settings in the unit to be completed. If the external DC power supply or LAN cable is disconnected before the settings are completed, the settings will be canceled. In this case, repeat the steps to establish the settings.

• When a firewall (including software) has been introduced, enable access to all the UDP ports.

Network settings (continued)

Installing the plug-in viewer software

To view IP images from the unit on a web browser, the “Network

Camera View 4S” plug-in viewer software (ActiveX

The plug-in viewer software can be installed directly from the unit.

<NOTE>

• [Automatic installation of viewer software] is set to [On] at the time of purchase, allowing you to install directly from the unit. If a message

appears in the web browser’s information bar, see page 117.

• When you display the Live screen [Live] on the personal computer for the first time, the installation screen for the plug-in viewer software (ActiveX) appears. Follow the instructions on the screen to perform installation.

• If the plug-in viewer software (ActiveX) installation screen continues to appear when switching screens, even after it is installed, restart the personal computer.

• A license is required for the plug-in viewer software for each personal

computer on which it is installed. You can view the number of times

the plug-in viewer software was automatically installed in the [Product

info.] tab of the Maintenance screen [Maintenance] (→ page 99).

For details on licenses, consult your local dealer.

• To uninstall the plug-in viewer software, select [Control Panel] [Programs] - [Uninstall a program] in Windows, and remove “Network

Camera View 4S”.

) must be installed.

To prevent unauthorized access to cameras

Enable the user authentication function

(Not available when the AW-RP50 is connected)

Remote cameras can be configured to allow access from the Internet. To prevent infringement of privacy and personality rights, information leaks, and other issues concerning unauthorized access by third parties, we recommend enabling the user authentication function upon installation.

Configuration example (refer to the operating instructions provided with your camera for further information about the settings used for your camera)

A Turn on user authentication B Set a new user name and password C Delete the default user name

Preparation:

1. Startup the web browser and display the “Live” page on a PC.

2. Click “Setup” button and then click “User mng.” button.

The user authentication window will be displayed.

A Select “On” for “User auth.”

Set to “Off” by default.

Then click “Set” button.

B Register a new user name and password

Select “1. Administrator” for the access level.

Then click “Set” button.

C Delete the default user name.

Click the “Delete” button after selecting the user name to be

deleted (“admin[1]”).

Depending on the model used, the screens shown in the

explanations may differ to the actual camera screens.

User name and password management

• Use a combination of characters and numbers that is difficult to

guess.

Avoid using a string of the same characters, such as “11111”, birth

dates, or telephone numbers. For details on valid characters and lengths, refer to “User

authentication screen” (→ page 84).

• Change user names and passwords periodically.

• Make sure to manage the configured user names and

passwords.

• Delete all user names that do not have an assigned user.

After changing the user name/password

Also change the user names and passwords registered to the following. Refer to the operating instructions provided with your camera for further information about the settings used for your camera.

• Remote camera controller (AW-RP50, AW-RP120)

• Remote operation panel (AK-HRP200)

• Browsers and applications on computers, tablets, and smartphones.

Basic shooting operations

1. Set the subject brightness to the appropriate level.

2. Turn on the power of all the units and devices in the

system.

3. Select the unit to be operated.

Even when using only one unit, it must still be selected from the controller.

4. Select the shooting mode.

One of four shooting modes (Scene1, Scene2, Scene3 or Scene4) — whichever one will best suit the shooting conditions — can be selected. The shooting modes are set by the user.

For details of the factory settings, refer to pages 54 to 57.

Select the mode that satisfies the shooting conditions and suits your preferences. When continuing to shoot in the same circumstances, there is no need to select another mode.

How to turn the power on and off

Turning the power on

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

5. Start shooting.

(After shooting, turn off the power of all the units and devices in the system.)

<NOTE>

• Some of the initial settings are auto settings and cannot be operated manually. To operate them manually, switch from the auto settings to the manual settings as required.

If the settings have already been changed and the original settings are to be restored, refer to the “What to do when encountering problems

in the basic shooting operations” (→ page 26) and “Camera screen” (→ page 39) in “Camera menu items”.

Turning the power off

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

When using a commercially available controller

Refer to the operating instructions for the controller.

Selecting the units

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

When using a commercially available controller

Refer to the operating instructions for the controller.

Selecting the shooting modes (scene files)

Types of shooting modes

One of four shooting modes (Scene1, Scene2, Scene3 or Scene4) — whichever one will best suit the shooting conditions — can be selected. The shooting modes are set by the user.

For details of the factory settings, refer to pages 54 to 57.

Select the mode that satisfies the shooting conditions and suits your preferences. The settings can be changed by menu operations.

• The results of the white balance and other adjustments are stored in the memory separately by shooting mode. Be absolutely sure to select the shooting mode before making any adjustments.

<NOTE>

• Some of the initial settings are auto settings and cannot be operated manually. To operate them manually, switch from the auto settings to the manual settings as required.

Scene1 [Scene1] Scene2 [Scene2] Scene3 [Scene3] Scene4 [Scene4]

The settings of your preferences can be established in line with the shooting scene, lighting and other conditions.

How to select the shooting mode

1. Press and hold the <OSD> button for about 2 seconds.

The Top Menu is displayed.

Top Menu

Camera Scene: Scene1 System Maintenance

2. Turn the <F1> dial to select [CAMERA], then press the

<F1> dial.

The [Camera] sub-menu is displayed on the monitor.

Camera

Scene Scene1 Brightness Picture Matrix Intelligent

Return

3. Turn the <F1> dial or <F2> dial and then confirm the item.

4. Press and hold the <OSD> button for about 2 seconds.

The camera menu display is exited.

For detailed operations, refer to the operating instructions for the controller.

Shooting

Changing the camera’s direction



Moving the camera toward the left or right (panning):

Tilt the <PAN/TILT> lever toward L or R.

Moving the camera up or down (tilting):

Tilt the <PAN/TILT> lever toward UP or DOWN.

Moving the camera diagonally:

Tilt the <PAN/TILT> lever diagonally.

Using the zoom function



Zooming in (the subject becomes magnified in size):

Tilt the <ZOOM> lever toward the TELE direction.

Zooming out (the subject becomes reduced in size):

Tilt the <ZOOM> lever toward the WIDE direction.

Switching the panning/tilting and lens operation



speed

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

What to do when encountering problems in the basic shooting operations

If the trouble is not resolved by taking the action suggested below, refer

to “Troubleshooting” (→ page 109).

The unit does not move.

• Select the unit to be operated by following the procedure below.

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

• If the unit’s status display lamp is off or lights up orange, it means that the unit’s power is not on.

Refer to “How to turn the power on and off” (→ page 23), and turn

on the power.

Multiple color bands (color bars) are displayed.

Switch to the camera image by pressing the <BARS> button.

The menu screen is displayed.

Press the <CAMERA OSD> button to exit the camera menu.

More advanced operations

Manual shooting (→ page 27)

• Manually adjusting the focus

• Manually adjusting the iris

• Manually adjusting the shutter speed

• Manually adjusting the gain

Preset memories (→ page 27)

Up to 100 settings for the camera direction (panning and tilting), zoom,

focus, iris, gain up and white balance can be registered in the preset memories, and called.

The lens focus is not adjusted automatically.

Press the <AUTO> button of <FOCUS> to switch to auto focusing.

The camera picture is too light or too dark.

• Press the <AUTO> button of IRIS to switch the lens iris adjustment to auto.

• Press the <AUTO> button of GAIN to switch the gain adjustment to auto.

Something is wrong with the coloring of the camera

pictures.

Refer to “Auto tracking white adjustment (ATW)” (→ page 28), and switch to “ATW”.

The camera menus are not displayed.

Restart the camera and open any of the camera menus within about a minute to display the menus in the SDI OUT 1/PM connector output and the web screen.

Check [OSD Mix] (→ page 49) on the camera menu [Others 3/5]

screen.

Black balance adjustment (→ page 29)

• This adjustment is performed to express the black accurately. Its setting also has an effect on the color tones of the entire screen.

• It must be performed when using the unit for the first time or when the unit has not been used for a prolonged period.

• It must be performed when the ambient temperature has changed significantly and at the change of the seasons.

• Once the black balance has been attained, no further adjustment is required provided that the unit is going to be used under the same conditions.

White balance adjustment (→ page 28)

• This adjustment is performed to express the white accurately. Its setting also has an effect on the color tones of the entire screen.

• It must be performed when using the unit for the first time or when the unit has not been used for a prolonged period.

• Perform adjustment when the lighting conditions or brightness changes.

• Once the white balance has been attained, no further adjustment is required provided that the unit is going to be used under the same conditions.

• White balance adjustment is not possible in night mode.

• When the white balance adjustment is set to [ATW], automatic white balance adjustment will occur continuously and changes in light sources and color temperature will be corrected automatically to produce natural pictures.

Black level (master pedestal) adjustment (→ page 29)

• This adjustment is performed to align the black level (pedestal level) of a multiple number of cameras.

• Ask your dealer to perform this adjustment.

Genlock adjustment (→ page 29)

• This adjustment is performed to achieve phase alignment by applying external synchronization (genlock) when a multiple number of cameras will be used or when the unit will be used in combination with other devices.

• Ask your dealer to perform this adjustment.

Manual shooting

Manually adjusting the focus

The lens focus can be adjusted manually.

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

<NOTE>

• When the focus is set to manual, the subject may go out of focus during panning, tilting and zooming. Therefore, the unit comes with a

function which compensates for this. (Focus ADJ With PTZ.)

This function was set to [On] at the factory. If the function has been set to [Off], either adjust the focus, as required, after zooming or set the focus to auto.

(→ page 49, page 78, page 81)

Manually adjusting the iris

The lens iris can be adjusted manually.

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

<NOTE>

• In the night mode, the iris is set to open as a measure to prevent video spying. Adjust the brightness at the light source.

Manually adjusting the shutter speed

The shutter speed can be set using two methods. One is a method that

specifies the time (where a time such as 1/250 sec. is designated), and

the other is a method that specifies the frequency (where synchro scan,

60.15 Hz, etc. is designated).

When shooting a TV screen or personal computer's monitor screen, the horizontal noise generated when the screen is shot can be minimized by adjusting the frequency to the screen frequency using synchro scan.

The procedure is the same as for “Basic setup operations” (→ pages 30 to 37).

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

Manually adjusting the gain

There are two ways to adjust the gain. One way involves using the

buttons on the controller; the other way involves using the Camera menu

or Web setup screen [Setup]. The gain can be adjusted more precisely using the Camera menu or Web setup screen [Setup].

For further details, refer to the “Gain” (→ page 40, page 72).

<NOTE>

• When adjusting the gain, the light quantity may change suddenly (causing the image output to be subjected to a shock).

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

Preset memories

This unit enables up to 100 settings for the camera direction (panning

and tilting), zoom, focus, iris, gain, white balance and digital extender to be registered in its preset memories, and called.

However, the number of settings that can be registered and called

depends on the type of controller that is used for operation.

• The focus and iris operating modes (manual and auto settings) are neither registered nor recalled. The current focus and iris values are registered.

• The focus and iris values can be recalled only when the manual settings are applicable.

• For the white balance, the current White Balance Mode adjustment values are registered. If a preset value is recalled when AWB A or AWB B is selected, the adjustment value selected when it was registered as a preset will be recalled. The R Gain and B Gain values

return to 0 in such cases.

<NOTE>

• When there is a large difference in the environmental temperature between the time of registration and the time the setting is called, displacement of the preset position may occur.

• If displacement occurs, perform registration again.

• When a manual operation is performed for pan, tilt, zoom, focus or iris during preset recall, the preset operation for the pan, tilt, zoom, focus or iris operation concerned will be aborted.

• If another preset has been recalled during an ongoing preset recall, the preset being recalled is aborted, and operation for the preset called last is performed instead.

In any case, the maximum gain of the automatic adjustment (AGC) can be set by the camera menu or Web setup screen [Setup].

For further details, refer to the “AGC Max Gain” (→ page 40, page 73).

When using an AW-RP50 or AW-RP120

Up to 100 entries can be registered/recalled.

For details, refer to the operating instructions for the controller.

When using an AK-HRP200

Preset memories cannot be registered or recalled.

White balance adjustment

Adjust the ratio between the three primary colors (RGB) to reproduce white accurately. If the white balance is out of adjustment, not only will white be reproduced poorly, but the color tones of the screen as a whole will also be degraded.

• Perform adjustment when using the unit for the first time or when the unit has not been used for a prolonged period.

• Perform adjustment when the lighting conditions or brightness changes.

Either AWB (automatic white balance adjustment) which initiates automatic adjustment when the <AWB> button on the controller has been pressed or ATW (automatic tracking white balance adjustment) which constantly adjusts the white balance can be selected for adjustment purposes.

The results of the AWB adjustment can be stored in two memories, A and B, when [AWB A] or [AWB B] has been selected for the white balance.

• Once the white balance values have been adjusted, their setup procedure will be completed simply by selecting them using the camera menus or Web setup screen [Setup], or by pressing the buttons on the controller, provided that they are going to be used under the same conditions as the ones established when the values were set. There is no need to set it again.

• Once a new setting is entered, the previous setting will be erased.

• White balance adjustment is not possible in night mode.

Use the two memories to store settings corresponding to different shooting conditions.

Automatic adjustment (AWB: AWB A or AWB B)

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

<NOTE>

• Proper white balance adjustment may not be possible if the object lighting is too weak or a bright light (e.g., fluorescent light) enters the screen.

• Since the unit has a built-in memory, the set white balance will remain in the memory even if power is turned off. Therefore, it is not necessary to reset the white balance if the color temperature of

those objects remains unchanged. However, it must be reset if the

color temperature changes, such as when you move from indoors to outside, or vice versa.

Auto tracking white adjustment (ATW)

When the white balance adjustment is set to [ATW], the white balance continues to be adjusted automatically all the time, and it is automatically corrected even when the light source or color temperature has changed to produce completely natural pictures.

<NOTE>

• ATW might not function properly when high brightness light (ex. fluorescent lamp) beams into a screen.

• White balance may not be accurately set if there is no white object in the scene being shot.

• The white balance may shift out of adjustment when different kinds of light sources such as sunlight and fluorescent lighting are applied.

3200K and 5600K presets

When [3200K] or [5600K] is selected for the white balance, the white balance is set using a color temperature of 3200 K (equivalent to halogen light) or 5600 K (equivalent to daylight), respectively.

VAR

When [VAR] is selected for the white balance, you can select a color

temperature between 2000 K and 15000 K.

<NOTE>

• The displayed [VAR] value does not guarantee an absolute value. Use the value as a reference.

White balance_END

Black balance adjustment

Adjust the zero levels of the three primary colors (RGB) to reproduce black accurately. If the black balance is out of adjustment, not only will black be reproduced poorly, but the color tones of the screen as a whole will also be degraded. Readjustment of the black balance is not required under normal circumstances but is necessary in the following situations.

• Perform adjustment when using the unit for the first time or when the unit has not been used for a prolonged period.

• Perform adjustment when the ambient temperature changes significantly, such as during changes of the season.

Black level (master pedestal) adjustment

The black level can be adjusted when using a multiple number of cameras including the unit. Ask your dealer to perform this adjustment. (Use a waveform monitor for the adjustment.) Adjust the black level in accordance with the units and devices used.

Genlock adjustment

The genlock adjustment is performed to achieve phase alignment by applying external synchronization (genlock) when a multiple number of cameras will be used or when the unit will be used in combination with other devices. This unit supports tri-level sync external synchronization signals. Ask your dealer to perform this adjustment. (Use a dual-trace oscilloscope for the adjustment.)

Automatic adjustment

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

When using an AW-RP50, AW-RP120, or AK-HRP200

Refer to the operating instructions for the controller.

Horizontal phase adjustment

Observe the waveforms of the external sync signal input (tri-level sync signal) and video signal output on the dual-trace oscilloscope, and use the controller to bring the horizontal phase into alignment.

External sync signal input (tri-level sync signal)

Video signal output

Bring the horizontal

phase into alignment.

Example: When the tri-level sync phase is adjusted

These operations can be performed using the camera menus by

following the operation steps in “Basic setup operations” (→ pages 30 to 37).

<NOTE>

• The unit is not equipped with an output connector for analog video signals. Observe and adjust the analog output of an SDI waveform monitor, or use the synchronous phase check function of the SDI waveform monitor.

Basic setup operations

Camera menus are displayed on the monitor when the unit’s settings are to be selected. The monitor is connected to the SDI OUT 1/PM connector.

Described below are the Basic setup operations for changing the

camera menu item settings using the controller (AW-RP50, AW-RP120 or AK-HRP200).

The basic camera menu operations involve displaying sub-menus from the Top Menu items, and selecting settings on the sub-menus. Some sub-menus have menu items for performing more detailed settings.

For detailed operations, refer to the operating instructions for the controller.

The camera menu operations are conducted using the controller.

<NOTE>

• Check that your controller is the following version.

AW-RP50: Ver 4.00.00 or later AW-RP120: Ver 3.00.00 or later AK-HRP200: Ver 6.00-00-0.00 or later

If the version older, an upgrade is required. For details on upgrading, visit the support page on the following website. http://pro-av.panasonic.net/

Controller operations



Camera menu operation

Selecting a camera to operate

Displaying the Top Menu Press and hold the <CAMERA OSD> button for about 2 seconds.

Selecting items Turn the <F1> dial.

Displaying sub-menus Press the <F1> dial.

Returning to the previous menu

Changing settings

Canceling setting changes

Exiting camera menu

operations

Press the <CAMERA STATUS> or <SELECTION> button.

Place the cursor on [Return], and press the <F1> dial. Place the cursor on [Return], and press the <SELECT> dial.

1. Press the <F1> dial to make the setting value blink.

2. Turn the <F1> dial to change the setting value.

3. Press the <F1> dial to confirm the setting value (blinking

Press and hold the <CAMERA OSD> button for about 2 seconds.

AW-RP50 AW-RP120 AK-HRP200

stops).

― ―

Controller

Press and hold the <SELECT> button for about 2 seconds.

→ The camera number in the camera number display area

blinks.

2. Press the lit <UP> and <DOWN> button.

→ Press the lit <UP> and <DOWN> buttons to select the

camera number.

3. Press the <SELECT> button.

→ Control of the selected camera is enabled.

Press and hold the <CHARA/MENU> button for about 2

seconds.

Turn the <SELECT> dial.

Press the <SELECT> dial.

Press the <SELECT> dial to make the setting value blink.

2. Turn the <SELECT> dial to change the setting value.

3. Press the <SELECT> dial to confirm the setting value (blinking stops).

Press and hold the <CHARA/MENU> button for about 2

seconds.

<NOTE>

• Perform the menu operations and exit from the menus using the controller which displayed the Top Menu. If a menu operation has been performed or a menu has been exited using another controller, first display the Top Menu and exit from it using one controller, and then display the Top Menu and exit from it using the other controller.

• The procedures used for this unit’s menu operations may differ from the ones used for the convertible cameras and HD integrated cameras which have already been released on the market. For details, refer to the Operating Instructions of the camera concerned.

• The response speed of the camera differs slightly depending on the controller used.

+ 94 hidden pages