Panasonic AK-HRP900P User Manual

Before attempting to connect, operate or adjust this product,

please read these instructions completely and save this manual for future use.

Model AK-HRP900P

Camera Controller

2

For Your Safety

FCC Note:

This device complies with Part 15 of the
FCC Rules. To assure continued
compliance follow the attached instal­lation instructions and do not make any
unauthorized modifications.

This equipment has been tested and
found to comply with the limits for a Class
A digital device, pursuant to Part 15 of
the FCC Rules. These limits are de­signed to provide reasonable protection
against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instruction manual,
may cause harmful interference to radio
communications. Operation of this equip­ment in a residential area is likely to
cause harmful interference in which case
the user will be required to correct the
interference at his own expense.

1 is the safety information.

CAUTION

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with
arrowhead symbol, within an
equilateral triangle, is intended to
alert the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.

The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and main­tenance (servicing) instructions
in the literature accompanying
the appliance.

CAUTION:

TO REDUCE THE RISK OF FIRE OR
SHOCK HAZARD AND ANNOYING
INTERFERENCE, USE THE RECOM­MENDED ACCESSORIES ONLY.

WARNING:

TO REDUCE THE RISK OF FIRE OR
SHOCK HAZARD, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR
MOISTURE.

The serial number of this product may
be found on the bottom of the unit.

This class A digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la classe A
est conforme à la norme NMB-003 du
Canada.

For CANADA

12 Volt Class II Power Supply Only.
(For Example: AW-PS505P)

For Your Safety

3

Contents

For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Check the Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Precautions for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Controls and their Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

_ Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

_ Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

_ Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

How To Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

_ Lens connection in the case of no swivel stand . . . . . . . . . . . . . . . . . . . . . . .13

Multi-purpose digital camera control system configuration 1 . . . . . . . . . . . . . . .14

Multi-purpose digital camera control system configuration 2 . . . . . . . . . . . . . . .15

Multi-purpose digital camera control system configuration 3 . . . . . . . . . . . . . . .16

Communication speed setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Example of Rack Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

_ How to rack-mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

_ How to change the rear panel position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Appearance and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

4

Outline

Coupling . . . . . . . . . . . . . . . . . . . . . . .1 pc

Multi-cable . . . . . . . . . . . . . . . . . . . . . .1 pc

Seal . . . . . . . . . . . . . . . . . . . . . . . . . . .1 pc

Setscrews . . . . . . . . . . . . . . . . . . . . .8 pcs

M4 x 8 mm . . . . . . . .4 pcs

M5 x 8 mm . . . . . . . .4 pcs

≥ This unit is a camera controller for multi-purpose camera (AK-HC900P). This

unit is connected to a multi-purpose camera with one multi-cable, and capable
of transmitting and receiving various camera and lens control signals, analog
picture signals of cameras, and generator lock signals (3-value SYNC).

≥ The extension distance between this unit and the camera is 33 ft (10m) max.
≥ It is possible to control the swivel stand from the pan-tilt control panel AW-

RP301 by using the swivel stand control input connector.

Check the Accessories

Precautions for Use

≥ We recommend that the AC adapter AW-PS505P is used for power supply.
≥ Handle the unit with care.

If dropped or given a strong shock, it may cause a trouble or accident.

≥ Use the unit in a temperature range of 32oF to 104oF (0oC to + 40oC).

If used at a temperature below 32oF or higher than 104oF, it may cause bad influences to
the component parts.

≥ Turn off the power before connecting or disconnecting the cable.

When connecting or disconnecting the cable, be sure to turn off the power switch of the
unit beforehand.

≥ Avoid using the unit outdoors.
≥ Install the unit 3.3 ft (1 m) away from the monitor.
≥ Maintenance

Pull out the power cord plug and clean the unit with dry cloth. If it is hard to clean,
moisten the cloth with a diluted neutral detergent solution and squeeze it well and lightly
wipe the unit.

≥ Do not use volatile solvents such as benzene or thinner.
≥ When using a chemical mop, carefully read the instructions.

Precautions

5

_Operation panel

POWER

ON OFF

SD CARD

OPERATE

ALARM

SCENE

MODE

PRE

CAM BAR TEST

USER1 USER2

Camera Controller

TALLY

MENU

ON

MENU

SPEED ZOOM

TELE

WIDE

FAR

NEAR

FOCUS

12345

PRESET

CC FLTER

3200

CROSS

63004300

ND FLTER

CLEAR 1/321/161/4

SHUTTER

OFF

SYNCRO

STEP

GAIN

0

S1 S2

S3

9dB 18dB

AUTO

WHITE BLACK

GAIN

BLACK

AUTO

M-PED

IRIS

CHECK

123<=>

?
@
A

B
C

D
E

F
G

: ;HIJ K L

4
5
6

7

8

9

1 Power indication LED [POWER]

It is lighted green when the power control switch 2 is ON. It goes out when the power
control switch 2 is OFF.

2 Power control switch [POWER ON/OFF]

With this switch turned ON, the unit and the camera connected are simultaneously
turned on. With it turned OFF, both of the unit and the camera are turned off.

3 SD card slot [SD CARD]

With an SD card inserted, the camera setting data can be recorded on the SD card.

4 Tally LED [TALLY]

It is lighted red when tally signal is input to the tally signal input terminal Q.

Controls and their Functions

6

5 Menu operation switch [MENU]

Operation switch for camera menu.
Item selection or data change can be done by turning this switch. When this switch
pushed, the item and data are settled.

6 Menu ON switch [MENU ON]

Used to turn the camera menu ON/OFF.

7 Preset memory switch [MEMO]

Preset memory can be done up to 5 points with respect to lens zoom, focus, and iris
position (when iris select switch K is at [MANU]). When using the preset memory, first
set the lens focus, zoom, and iris. Next, push this switch, then the switch is lighted.
Subsequently, push the desired preset position select switch 8. With the data stored in
the memory, the switch is lighted.

8 Preset position select switch [PRESET]

It calls the lens zoom, focus and iris settings previously stored in the memory, and
brings the lens into preset operation.

9 Speed change switch [SPEED]

High speed operation is obtained when the zoom operation lever : and the focus
adjust lever ; are operated while pressing this switch. The switch is lighted while being
pressed.

: Zoom operation lever [ZOOM TELE/WIDE]

Used for zoom operation of the lens. The zoom speed changes with the shifting angles
of the lever. With the zoom operation lever direction change switch T set at [NOR],
when the lever is shifted to [TELE], the zoom operates in a telescopic mode, and when
shifted to [WIDE], it operates in a wide angle mode. With the zoom operation lever
direction change switch T set to [REV], the zoom can be operated in the opposite
direction.

; Focus adjust lever [FOCUS FAR/NEAR]

Used to adjust the lens focus. The focus can be controlled in speed variable fashion by
regulating the shifting angle of this lever.
With the focus adjust direction change switch U set at [NOR], when this lever is shifted
to [FAR], the focus is adjusted to a far distance, and when shifted to [NEAR], the focus
is adjusted to a near distance. With the focus adjust direction change switch U set to
[REV], the focus can be adjusted in the opposite direction.

< Operation panel active switch [OPERATE]

This is an active switch for panel function. It can be operated when the switch is lighted.
It does not work when the switch is not lighted.

Controls and their Functions

7

Controls and their Functions

= Alarm indication LED [ALARM]

It lights up when an alarm is generated (in case of fan stop, wrong communication
speed, etc.).

Note:

In case of wrong communication speed, change the DIP SW position in the unit to
match the camera and communication speed so that the alarm goes out.

> Scene file select switch [SCENE]

Used to select the scene file previously set on the camera.

Note:

With [PRESET] selected, it results in the factory-adjusted setting.

? Mode select switch [MODE]

Used to select the camera color bar signal, test signal and camera picture signal. With
the switch set to [BAR], [TEST], the color bar signal and the test signal are output from
the monitor signal output terminal of this unit. With it set to [CAM], the picture taken by
the camera is output.

@ Auto white start switch [AUTO WHITE]

With this switch pressed, the white balance is automatically adjusted. During the
operation, WHTE LED blinks, and it goes out when the adjustment is normally finished.
In case of NG, it lights up for a while and then goes out.

Note:

It does not operate when the mode is [BAR].

A Auto black start switch [AUTO BLACK]

With this switch pressed, the lens is automatically closed, and the black balance is
adjusted. During the operation, BLACK LED blinks, and it goes out when the
adjustment is normally finished. In case of NG, it lights up for a while and then goes
out.

B R/B gain adjust volume [GAIN]

Used to adjust the R/B signal gain of the camera.

C R/B pedestal adjust volume [BLACK]

Used to adjust the R/B signal pedestal level of the camera.

D ND filter select switch [ND FILTER]

Used to select the optical filter (ND) of the camera.

E CC filter select switch [CC FILTER]

Used to select the optical filter (CC) of the camera.

8

F Gain select switch [GAIN]

Used to select the master gain of the camera. It changes in the order of 0dB )9dB
)18dB )S1 (Super gain 1) )S2 )3dB )0dB.

Note:

For super gain setting, check with the camera menu.

G Shutter select switch [SHUTTER OFF/STEP/SYNCHRO]

Used to select the electronic shutter of STEP and SYNCHRO set on the camera.

Note:

For electronic shutter setting, check with the camera menu.

H Indication change switch [CHECK]

Used to change the indication item.

I Indicator

It indicates the F value of iris.

J Master pedestal adjust volume [M-PED]

Used to adjust the pedestal setting of Y (luminance) signal of the camera.

K Lens iris auto/manual select switch [IRIS AUTO]

Used to select the lens iris adjusting method.
With the switch set to [AUTO], the lens is shifted to auto iris mode, and the iris is
automatically adjusted according to the amount of light coming into the lens.
With the switch set to [MANU], the lens iris can be moved in the range from close to
open by turning the lens iris adjust VR (volume) L.
When storing the lens iris in the preset position select switch 8 by using the preset
memory switch 7, set to [MANU] mode. It does not work in [AUTO] mode.

L Iris adjust volume [IRIS]

When the lens iris auto/manual select switch K is set at [MANU], the lens iris can be
moved in the range from close to open.
When the lens iris auto/manual select switch K is set at [MANU], press the preset
position select switch 8 to call the preset memory, then the lens iris position is set to
the preset memory position irrespective of the VR (volume) position. After that, when
the VR is turned, the lens iris returns to the value of VR.

Controls and their Functions

9

Pin No

8

9
10
11
12
13
14
15

Signal
Y signal output
Pb signal output
Pr signal output
Sync signal input
DC 12V
Frame GND
TXD (H)

Signal
Y signal GND
Pb signal GND
Pr signal output
Sync signal GND
DC GND
TXD (C)
RXD (H)
RXD (C)

Pin No

1
2
3
4
5
6
7

CAMERA I / F

MONITOR OUT G/L IN TALLY IN

BREAKER

DC 12V IN

YPb Pr

P/T CONT

MN O P Q R S

_Rear panel

17

234

56

8

9101112131415

TXD: Data from camera to remote controller.
RXD: Data from remote controller to camera.

N Swivel stand control signal input connector [P/T CONT (RJ-45)]

Connects the swivel stand control signal output of the pan-tilt control panel (AW­RP301).

O Monitor signal output connector [Y/G, Pb/B, Pr/R] (BNCk3)

Outputs the analog signal from the camera.
The output can be changed to R, G, B/Y, Pb, Pr by the camera menu setting.

P Synch signal input connector [G/L IN] (BNCk1)

Inputs the sync signal to the camera. Input 3-value SYNC as the synch signal.

Q Tally signal input connector [TALLY IN] (2-pin connector block)

Connected to the tally connector from the system. When the HOT connector is at GND
level, the tally LED is lighted.

Controls and their Functions

M Camera connector [CAMERA I/F]

Connected to the camera (AK-HC900P) with the attached cable.

10

R Breaker [BREAKER]

DC power breaker. The breaker operates to cut off the power in case of over-current.

S DC12V input connector [DC12V IN] (XLR4-pin)

Connects the AC adapter. We recommend that the AW-PS505P (option) is used.

1

2

3

4

Controls and their Functions

Pin No

1

2, 3

4

Signal

GND

–––

12V

11

ZOOM

REVERSE

FOCUS

REVERSE

NOR REV NOR REV

TU

_Front panel

T Zoom operation lever direction change switch [ZOOM REVERSE]

Used to change the direction of the zoom operation lever.
With this switch set at [NOR], when the zoom operation lever : is shifted to [TELE], the
zoom operates in a telescopic mode, and when shifted to [WIDE], zooming is made in a
wide angle mode.
With this switch set to [REV], it can be operated in the opposite direction. Also, with this
switch set to [REV], the operating direction does not match the indication on the panel.
In that case, use the attached seal for proper indication.

U Focus adjust direction change switch [FOCUS REVERSE]

Used to change the direction of the focus adjust lever.
With this switch at [NOR], when the focus adjust lever ; is shifted to [FAR], the focus is
adjusted to a far distance, and when shifted to [NEAR], the focus is adjusted to a near
distance.
With this switch set to [REV], focusing can be made in the opposite direction. Also, with
this switch set to [REV], the operating direction does not match the indication on the
panel. In that case, use the attached seal for proper indication.

Controls and their Functions

12

Make the connection with power supply to the unit turned off.

≥ Use AW-PS505P (option) as the AC adapter for control panel.
≥ Use a swivel stand, AW-PH300A, AW-PH500, AW-PH600, and an adapter suited for

the swivel stand.

≥ When no swivel stand is used, connect both of the motor-driven zoom lens iris control

cable and remote (zoom/focus) cable to the camera. (see page 13)

≥ When a swivel stand is used, connect the iris control cable to the camera, and the

remote (zoom/focus) cable to the swivel stand. (see the illustration below)

≥ For the connection system of each unit, refer to pages 14 to 16.

BREAKER

ZOOM/
FOCUS

SDI OUT

1

2

1

/

F

G/LI N Pb OUT Pr / SDI

OUT

Y/VIDEO

OUT

1394

CONTROL IN

IP/RP

DC12V

IN

CAMERA I/F

LENSE I/F

ND/EXT

SDI

IN

CSOP

How to Connect

To iris connector

Iris control
cable

Remote
(zoom/focus
control) cable

To lens interface
connector

≥ Connect the motor-driven zoom

lens iris control cable to the
camera, and the remote
(zoom/focus control) cable to the
swivel stand. If the motor-driven
zoom lens remote (zoom/focus
control) cable is connected to
the camera, the lens cannot be
controlled.

13

_Lens connection in the case of no swivel stand

_How to mount the lens

≥ A lens of any maker’s can be used provided that it is a bayonet type (B4 mount) lens

of 2/3 inch standard.*

1 Turn the lens fixing ring knob counterclockwise and remove the lens mount cap.
2 Mount the lens and completely secure it by turning the lens fixing ring knob

clockwise.

3 Connect the iris control cable to the lens connector.
4 Connect the remote (zoom/focus control) cable to the zoom/focus connector on the

rear panel.

*Note that some lenses are uncontrollable with respect to zoom and focus function.

How to Connect

BREAKER

ZOOM/
FOCUS

SDI OUT

1

2

1

/

F

720

PROGRESSIVE

Iris control cable (to
lens connector)

Remote (zoom/focus control)
cable
(Connect the cable to the swivel
stand when used.)

Lens fixing ring knob

14

O I

BREAKER

ZOOM/
FOCUS

SDI OUT

1

2

1

/

F

POWER

ON OFF

SD CARD

OPERATE

ALARM

SCENE

MODE

PRE

CAM BAR TEST

USER1 USER2

Camera Controller

TALLY

MENU

ON

MENU

SPEED ZOOM

TELE

WIDE

FAR

NEAR

FOCUS

12345

PRESET

CC FLTER

3200

CROSS

63004300

ND FLTER

11/321/161/4

SHUTTER

OFF

SYNCRO

STEP

GAIN

0

S1 S2

S3

9dB 18dB

AUTO

WHITE BLACK

GAIN

BLACK

AUTO

M-PED

IRIS

CHECK

Multi-cable (17ft)
AK-HDMLTCA05

Camera controller

AK-HRP900P

D-SUB 15-pin

D-SUB 15-pin

HD monitor

AC adapter

AW-PS505P

Ext. sync signal (3-value SYNC)

DC power
cable

Coaxial cable (5C-FB)HD-SDI

Remote
control
spec. lens

Remote (zoom/focus
control) cable

Multi-purpose digital camera control system configuration 1

Multi-purpose digital

camera

AK-HC900P

15

Multi-purpose digital camera control system configuration 2

Swivel stand

AW-PH300A

Multi-purpose digital camera
AK-HC900P

Multi-cable (17ft)
AK-HDMLTCA05

Camera controller

AK-HRP900P

HD monitor

AC adapter

AW-PS505P

Ext. sync signal (3-value SYNC)

DC
power
cable

Coaxial cable (5C-FB)HD-SDI

Remote
(zoom/focus
control) cable

AC adapter

AW-PS301

AC adapter

AW-PS505P

Swivel stand controller

AW-RP301

Swivel stand control is
possible for AW­PH500/PH600 as well.

Remote
control
spec. lens

Remote
(zoom/focus
control) cable

BREAKER

ZOOM/
FOCUS

1

SDI OUT

2

/

F

1

O I

ND/EXT

IN

SDI

LENSE I/F

CAMERA I/F

DC12V

CONTROL IN

IN

1394

IP/RP

CSOP

G/LI N Pb OUT Pr / SDI

Y/VIDEO

OUT

OUT

O I

ON OFF

POWER

SD CARD

TALLY

MENU

ON

MENU

PRESET

12345

SPEED ZOOM

TELE

FAR

WIDE

NEAR

Camera Controller

SCENE

OPERATE

ALARM

PRE

USER1 USER2

MODE

AUTO

CAM BAR TEST

WHITE BLACK

GAIN

BLACK

CC FLTER

ND FLTER

3200

CROSS

63004300

11/321/161/4

SHUTTER

GAIN

OFF

SYNCRO

STEP

0

9dB 18dB

S1 S2

FOCUS

S3

CHECK

IRIS

M-PED

AUTO

16

Multi-purpose digital camera control system configuration 3

O I

BREAKER

ZOOM/
FOCUS

SDI OUT

1

2

1

/

F

G/LI N Pb OUT Pr / SDI

OUT

Y/VIDEO

OUT

1394

CONTROL IN

IP/RP

DC12V

IN

CAMERA I/F

LENSE I/F

ND/EXT

SDI

IN

CSOP

O I

O I

POWER

ON OFF

SD CARD

OPERATE

ALARM

SCENE

MODE

PRE

CAM BAR TEST

USER1 USER2

Camera Controller

TALLY

MENU

ON

MENU

SPEED ZOOM

TELE

WIDE

FAR

NEAR

FOCUS

12345

PRESET

CC FLTER

3200

CROSS

63004300

ND FLTER

11/321/161/4

SHUTTER

OFF

SYNCRO

STEP

GAIN

0

S1 S2

S3

9dB 18dB

AUTO

WHITE BLACK

GAIN

BLACK

AUTO

M-PED

IRIS

CHECK

Swivel stand

AW-PH300A

Multi-purpose digital camera

AK-HC900P

Multi-cable (17ft)
AK-HDMLTCA05

Camera controller

AK-HRP900P

HD monitor

AC adapter

AW-PS505P

DC
power
cable

Coaxial cable (5C-FB)HD-SDI

Remote
(zoom/focus
control) cable

AC adapter

AW-PS301

AC adapter

AW-PS505P

Swivel stand controller

AW-RP301

Swivel stand control is
possible for AW­PH500/PH600 as well.

AC adapter

AW-PS300

Multi-cable (1.7ft)
AK-HDMLTCA05

Interface adapter

AK-HTF900P

Trans-

mission

Remote
control
spec. lens

17

The communication speed is factory-adjusted to 38.4Kpbs.
In case it does not match the communication speed of multi-purpose camera AK-HC900P,
the alarm LED is lighted. Remove the rear panel and change the DIP SW on the board
and adjust it to the communication speed of the camera.

SW3

ON

1234

ON

1234

ON

1234

ON

1234

5678

Change the
communication report
by the combination of
SW3 No.1 and No.2 on
ROP CPU board.

125Kbit/Sec

38.4Kbit/Sec

9600Kbit/Sec

SW5 SW4SW3

Remove the
screw and open
the bottom
plate, then DIP
SW can be seen
in there.

Communication Speed Setting

18

_How to rack-mount

Install the main body on the rack as shown below.

Remove the rack mount
bracket screw when installing

Rack mount bracket

Attached
screw

Coupler

Coupler
fitting
holes

Example of Rack Mount

CAMERA I / F

MONITOR OUT G/L IN TALLY IN

BREAKER

DC 12V IN

YPb Pr

P/T CONT

CAMERA I / F

MONITOR OUT G/L IN TALLY IN

BREAKER

DC 12V IN

YPb Pr

P/T CONT

19

_How to change the rear panel position

1 Remove the three screws on the

bottom to remove the blank panel.

* When installing, take care so that the internal wires are not caught by the panel.

3 Install the rear panel on the bottom with

the three screws.

ScrewScrew

Screw

Blank panel

Blank panel

Example of Rack Mount

Screw

2 Remove the three screws on the rear

panel to remove the rear panel.

4 Install the blank panel on the rear side

with the three screws.

20

Appearance and Dimensions

( ): mm

ZOOM

REVERSE

FOCUS

REVERSE

NOR REV NOR REV

CAMERA I / F

MONITOR OUT G/L IN TALLY IN

BREAKER

DC 12V IN

YPb Pr

P/T CONT

POWER

ON OFF

SD CARD

OPERATE

ALARM

SCENE

MODE

PRE

CAM BAR TEST

USER1 USER2

Camera Controller

TALLY

MENU

ON

MENU

SPEED ZOOM

TELE

WIDE

FAR

NEAR

FOCUS

12345

PRESET

CC FLTER

3200

CROSS

63004300

ND FLTER

11/321/161/4

SHUTTER

OFF

SYNCRO

STEP

GAIN

0

S1 S2

S3

9dB 18dB

AUTO

WHITE BLACK

GAIN

BLACK

AUTO

M-PED

IRIS

CHECK

8-5/16z (210)

6-15/16z (176) 5/8z

(14.5)

2-1/4z (57)

5/8z

(15)

21

Swivel stand control input:
System tally input:
Switch function:

Adjusting function:

Connection cable:
Cable max. extension distance:
Operating temperature range:
Dimensions:

Weight:
Finish:

Control signal (RJ-45 8P modular jack)
Tally signal (2P connector block)
Power control, preset memory, preset position select,
speed polarity change, menu ON/OFF, menu operation,
operation panel active, scene file select, mode select,
auto white start, auto black start, ND filter select, CC
filter select, gain select, shutter select, lens iris
auto/manual select, indication change, zoom operation
lever direction change, focus adjust direction change.
Iris (lens iris), zoom, focus, R/B gain, master pedestal,
R/B pedestal
Multi-cable 1 pc
33 ft (10m)
32oF to 104oF (0oC to +40oC)
8-5/16(W)k3-1/2(H)k6-15/16(D) inch
(210k88k176 mm)
Approx. 3.3 lbs (1.5kg)
AV ivory coating (Munsell 7.9Y 6.8/0.8 approx. color)

1is the safety information.

Power supply: DC +12V (XLR 4-pin connector)
Power consumption: 5 W (camera controller only)

Specifications

Weight and dimensions shown are approximate.
Specifications are subject to change without notice.

22

Memo

23

Memo

Printed in Japan
VQT0A79

PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY

UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA

Executive Office:

One Panasonic Way 4E-7, Secaucus, NJ 07094 [phone]

EASTERN ZONE

One Panasonic Way 4E-7, Secaucus, NJ 07094 [phone]

Southeast Region:

1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 [phone]

Central Region:

1707 N Randall Road E1-C-1, Elgin, IL 60123 [phone]

WESTERN ZONE:

3330 Cahuenga Blvd W., Los Angeles, CA 90068 [phone]

Government Marketing Department:

52 West Gude Drive, Rockville, MD 20850 [phone]

Broadcast PARTS INFORMATION & ORDERING:

9:00 a.m. – 5:00 p.m. (EST) [phone]/24 Hr. Fax [phone]
Emergency after hour parts orders [phone]

TECHNICAL SUPPORT:

Emergency 24 Hour Service [phone]

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3 [phone]

Panasonic de Mexico S.A. de C.V.

Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127

Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.

San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 [phone]

F0902H

@

3