Page 1
Panasonic Broadcast
AJ-SPC700p
Menu Information
Page 2
Chapter 8 Menu Description Tables (continued)
8-2 SYSTEM SETTING
8-2-1 SYSTEM MODE
Items/
Data Saved
REC SIGNAL CAM
–CUFE
ASPECT 16:9
–CUFE
REC MODE 50M
–CUFE
SET UP 0%
–CUFE
REC TALLY RED
–CUFE
ACCESS LED ON
–CUFE
Adjustable
VIDEO
1394
4:3
25M
DV
7.5%A
GREEN
CHAR
OFF
Range
Remarks
Select video input signals.
Record the signal from the
CAM
camera
VIDEO:
Record the signal from the
GENLOCK IN terminal
1394: Record the signal from the 1394
input terminal (when optional
AJ-YAD800G is attached)
<Notes>
z After the power has been turned
OFF, this setting defaults to CAM
when the power is turned ON again.
z With VIDEO selected, to synchronise
this camera-recorder to the video
signal (VBS) that is input to the
GENLOCK IN terminal, the
GENLOCK item in [8-2-6 GENLOCK]
must be set to EXT.
Select the aspect ratio for recording.
16:9: Record in <16:9> aspect ratio.
4:3: Record in <4:3> aspect ratio.
Select the recording mode.
50M: Record in DVCPRO50 format.
25M: Record in DVCPRO format.
DV: Record in DV format.
Switch the setup.
0%: Setup is switched to 0% for both
the camera output and the
recording.
7.5%A
: Setup is switched to 7.5% for
the camera output and 0% for
the recording.
Selects display of the recording status
of the camera when the AJ-SPC700P is
controlling an external VTR, by setting
the menu option 1394 CONTROL to
“BOTH”.
The menu option 1394 CONTROL is
found in the OPTION MODE screen on
the SYSTEM setting page.
RED: The red tally lamp lights up.
GREEN
:The green tally lamp lights up.
CHAR
: The VF displays [REC] in
characters.
<Note>
1394 control menu options are only
displayed when an IEEE1394 interface
board (AJ-YAD800G, optional
accessory) is attached. For more
information, see the AJ-YAD800G
instruction manual.
Select whether or not to enable
illumination of the P2 card access
LEDs.
ON: Enable the P2 card access
LEDs to light up for card status
indications.
OFF: LEDs remain off.
Items/
Data Saved
USB ON
––UF–
Adjustable
Range
OFF
Remarks
Select the USB drive mode when using
the P2 card as bulk storage by
connecting the AJ-SPC700P with a PC
via USB2.0.
ON: Switches to the USB drive
mode. Recording, playback or
thumbnail operation via the AJSPC700P is not permitted.
OFF: Stops the USB drive mode, and
returns to normal operation.
<Note>
After the power is turned off, this setting
defaults to “OFF” when the power is
next turned on.
8-2-2 OPTION MODE
Items/
Data Saved
SAVE SW (AUD
OUT)
–CUF–
SAVE SW (LCD) ON
–CUF–
<Note>
Menu options for setting 1394 are displayed when an
IEEE1394 interface board (AJ-YAD800G, optional) is
attached. For more information, see the AJ-YAD800G
instruction manual. Note that the AJ-SPC700P incorporates
the following additional items:
Items/
Data Saved
1394
CONTROL
–CUF–
1394 CMD SEL REC_P
–CUF–
Adjustable
Range
ON
OFF
OFF
Adjustabl
e Range
OFF
BOTH
STOP
Remarks
Select whether or not to forcibly disable
the audio output when the SAVE ON/
OFF switch is set to [ON].
ON: Disable audio output.
OFF: Enable audio output.
Select whether or not to automatically
turn off the LCD monitor when the
SAVE ON/OFF switch is set to [ON].
ON: Turn off LCD monitor.
OFF: Do not turn off LCD monitor.
Remarks
Select the control method for recording
when an external device for backup
recording is connected via the DVCPRO/
DV connector:
OFF: The external device is not
controlled.
BOTH:Recording is performed by both
the AJ-SPC700P and the external
device.
Determine the recording operation of the
external backup device when the REC
START/STOP button is pressed:
REC_P
: Record/Pause
STOP:Record/Stop
8
The ____ in the Adjustable Range column indicates the
preset mode.
99
Page 3
Chapter 8 Menu Description Tables (continued)
8-2-3 REC FUNCTION 8-2-4 OUTPUT SEL
Items/
Data Saved
PRE REC
MODE
–CUF–
PRE REC TIME 1SEC
–CUF–
LOOP REC
MODE
–––F–
VOICE MEMO
RESERV
–CUF–
REC START ALL
–CUF–
P.ON REC
SLOT SEL
–CUF–
Adjustable
Range
ON
OFF
:
8SEC
:
15SEC
ON
OFF
ON
OFF
NORMAL
HOLD
SLOT1
Remarks
Select whether or not to enable PRE
RECORDING.
ON: PRE RECORDING enabled.
OFF: PRE RECORDING disabled.
<Note>
Specify the PRE RECORDING time by
using the menu option PRE REC TIME.
Set PRE RECORDING.
1-15SEC:
Set the length of time that can be
retrospectively recorded before the
REC START button is pressed.
<Note>
The maximum selectable range is 8
seconds when the REC MODE in the
<SYSTEM MODE> screen is set to
50M (DVCPRO50).
Select whether or not to enable LOOP
REC.
This setting can be used with PRE
RECORDING features.
ON: Enable LOOP REC.
OFF: Disable LOOP REC.
<Note>
After the power is turned off, this item
will default to OFF the next time the
power is turned on.
Set the available memory space for
voice memos in P2 cards.
ON: Reserve a voice memo area of 10
minutes or longer separately from
the video recording capacity. The
voice memo area can be used
even when FULL is displayed for
the recording capacity of the P2
card.
OFF: Do not reserve any voice memo
space.
<Note>
Even when this item is set to OFF, and
FULL is displayed for the P2 card’s
recording capacity, it may be possible to
record voice memos depending on the
status of the P2 card.
Select operating modes that allow
recording to start.
ALL: Allow recording to start during
stop, recording pause, and
playback.
NORMAL:
Allow recording to start during
stop and recording pause.
Select the recording order of the slot
when the power is turned on.
HOLD:
The recording order starts with the
card previously selected when the
power was turned off.
SLOT1:
The recording order starts with the
card that is inserted in Slot 1 when
the power is turned on.
Items/
Data Saved
VIDEO OUT
SEL
–CUF–
OUTPUT CHAR MENU
–CUF–
LCD MON
CHAR
–CUF–
VF MODE EE/PB
–CUF–
THUMBNAIL
OUT
–CUF–
Adjustable
Range
VBS
VF
Y
ONLY
TC
STATUS
ON
OFF
EE
ON
OFF
Remarks
Select the output signal on the VIDEO
OUT connecter.
VBS:Output a regular composite
signal.
VF: Output a VF Y signal. The status
display is also superimposed.
Y: Output a component Y signal.
Set the character contents
superimposed onto the output signals
for the VIDEO OUT connecter.
MENU ONLY:
Displays only when the menu
characters are superimposed. No
display appears when other
characters are superimposed.
TC:Display the time code. (Displays the
menu when menu characters are
superimposed.)
<Note>
The TC display position moves up and
down depending on the camera ID
position.
STATUS:
Display the same characters
superimposed on the VF signal.
(Displays the menu when menu
characters are superimposed.)
Select whether or not to superimpose
characters on the LCD monitor. (The
character content is the same as the
video output signal.)
ON: Enable superimpose.
(Not interlocked with the VIDEO
OUT CHARACTER switch.)
OFF: Disable superimpose.
(Not interlocked with the VIDEO
OUT CHARACTER switch.)
Select the image to display in the
viewfinder.
EE/PB
: Display the playback image in
the playback mode.
EE: Always display the camera
image.
Select whether or not to output clip
thumbnails displayed on the LCD
monitor to the video output signals.
ON: Enable output.
OFF: Disable output.
The ____ in the Adjustable Range column indicates the
preset mode.
100
Page 4
Chapter 8 Menu Description Tables (continued)
8-2-5 LCD MONITOR 8-2-6 GENLOCK
Items/
Data Saved
BRIGHTNESS –7
–CUF–
COLOR LEVEL –7
–CUF–
CONTRAST –7
–CUF–
BACKLIGHT NORMAL
–CUF–
SELF SHOOT NORMAL
–CUF–
ASPECT CONV. SQUEEZE
–CUF–
Adjustable
Range
:
+0
:
+7
:
+0
:
+7
:
+0
:
+7
HIGH
MIRROR
LT.B OX
Remarks
Adjust the LCD monitor brightness.
Adjust the LCD monitor chroma level.
Adjust the LCD monitor contrast.
Select whether or not to set the LCD
monitor brightness to always high.
NORMAL
: The brightness changes
according to the
HIGH: Set to always high.
Select whether or not to change the
LCD monitor to mirror image.
NORMAL
MIRROR
Select a screen ratio for images
displayed on the LCD monitor.
SQEEZE
LT. BO X
<Note>
This item is enabled only when
ASPECT described in “8-2-1 SYSTEM
MODE” is set to16:9.
BRIGHTNESS setting.
: Do not change to mirror
image.
: Change to mirror image.
: Display images in the squeeze
size.
: Display images in the letter
box size.
Items/
Data Saved
GENLOCK INT
–CUFE
H PHASE
COARSE
–––––
H PHASE FINE –160
–––––
SC PHASE
COARSE
–––––
SC PHASE
FINE
–––––
Adjustable
Range
EXT
–50
:
+00
:
+50
:
+000
:
+160
0
1
:
3
–75
:
+00
:
+75
Remarks
Switch the camera synchronising
signal.
INT: Synchronise with the internal
reference signal regardless of the
reference signal input to the
GENLOCK IN terminal.
EXT: Synchronise with the reference
signal input to the GENLOCK IN
terminal.
Perform coarse phase adjustment for
horizontal hold when configuring a
system.
Perform fine phase adjustment for
horizontal hold when configuring a
system.
<Note>
This adjustment simultaneously shifts
the SC phase.
Perform coarse SC PHASE adjustment
when GENLOCK is set.
Perform fine SC PHASE adjustment
when GENLOCK is set.
<Note>
When adjusting GENLOCK, please
adjust H PHASE first, and then adjust
SC PHASE.
The ____ in the Adjustable Range column indicates the
preset mode.
8
101
Page 5
Chapter 8 Menu Description Tables (continued)
8-3 PAINT
8-3-1 ROP 8-3-2 MATRIX
Items/
Data Saved
Adjustable
Range
MASTER PED –200
:
+005
:
SCUFE
+200
MASTER DTL –31
:
+00
SCUFE
MASTER
GAMMA
SCUFE
:
+31
0.35
:
0.45
:
0.75
KNEE POINT 70.0%
:
85 0%
:
SCUFE
107.0%
KNEE SLOPE 0
:
50
SCUFE
:
99
R GAIN –200
:
+000
:
SCUFE
+200
G GAIN –200
:
+000
SCUFE
:
+200
B GAIN –200
:
+000
:
SCUFE
+200
R PEDESTAL –100
:
+000
:
SCUFE
+100
G PEDESTAL –100
:
+000
SCUFE
:
+100
B PEDESTAL –100
:
+000
:
SCUFE
+100
Remarks
Set the master pedestal level.
Set the H Detail and V Detail levels.
Set MASTER GAMMA in 0.01 steps.
Set the KNEE POINT position in 0.5%
steps.
Set the KNEE slope.
Set the Rch gain.
Set the Gch gain.
Set the Bch gain.
Set the Rch pedestal level.
Set the Gch pedestal level.
Set the Bch pedestal level.
Items/
Data Saved
MATRIX
TA B LE
SCUFE
MATRIX R-G –31
SCUFE
MATRIX R-B –31
SCUFE
MATRIX G-R –31
SCUFE
MATRIX G-B –31
SCUFE
MATRIX B-R –31
SCUFE
MATRIX B-G –31
SCUFE
MATRIX
TA B LE
SCUFE
Adjustable
Range
A
B
:
+06
:
+31
:
+12
:
+31
:
+06
:
+31
:
–01
:
+31
:
+07
:
+31
:
–05
:
+31
OFF
A
B
Remarks
Select the color correction table. 2
types of tables can be stored: type A
and type B.
Adjust the tint.
Adjust the tint.
Adjust the tint.
Adjust the tint.
Adjust the tint.
Adjust the tint.
Select the color correction table to be
applied to the selected GAIN switch (L/
M/H).
<Note>
The items indicated by are the setting items for PAINT
MENU SW() R/W in the <SD CARD R/W SELECT>
screen. The items without are the setting items for PAINT
MENU LEVEL R/W.
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information.
The ____ in the Adjustable Range column indicates the
preset mode.
102
Page 6
Chapter 8 Menu Description Tables (continued)
8-3-3 COLOR CORRECTION 8-3-4 LOW SETTING
Items/
Adjustable
Data Saved
R
(SAT/PHASE)
SCUFE
R-Mg
(SAT/PHASE)
SCUFE
Mg
(SAT/PHASE)
SCUFE
Mg-B
(SAT/PHASE)
SCUFE
B
(SAT/PHASE)
SCUFE
B-Cy
(SAT/PHASE)
SCUFE
Cy
(SAT/PHASE)
SCUFE
Cy-G
(SAT/PHASE)
SCUFE
G
(SAT/PHASE)
SCUFE
G-Yl
(SAT/PHASE)
SCUFE
Yl
(SAT/PHASE)
SCUFE
Yl-R
(SAT/PHASE)
SCUFE
COLOR
–63
:
+00
:
+63
–63
:
+00
:
+63
–63
:
+00
:
+63
–63
:
+00
:
+63
–63
:
+00
:
+63
–63
:
+00
:
+63
–63
:
+00
:
+63
–63
:
+00
:
+63
–63
:
+00
:
+63
–63
:
+00
:
+63
–63
:
+00
:
+63
–63
:
+00
:
+63
CORRECTONOFF
SCUFE
Range
Remarks
Perform red color correction (saturation
and hue).
Perform color correction (saturation and
hue) between red and magenta.
Perform magenta color correction
(saturation and hue).
Perform color correction (saturation and
hue) between magenta and blue.
Perform blue color correction
(saturation and hue).
Perform color correction (saturation and
hue) between blue and cyan.
Perform cyan color correction
(saturation and hue).
Perform color correction (saturation and
hue) between cyan and green.
Perform green color correction
(saturation, hue).
Perform color correction (saturation,
hue) between green and yellow.
Perform yellow color correction
(saturation, hue).
Perform color correction (saturation,
hue) between yellow and red.
Select whether or not to enable color
correction for the selected GAIN switch
(L/M/H).
ON: Enable correction.
OFF: Disable correction.
Items/
Data Saved
MASTER
GAIN
SCUFE
H.DTL LEVEL 00
SCUFE
V.DTL LEVEL 00
SCUFE
DTL CORING 00
SCUFE
H.DTL FREQ. 00
SCUFE
LEVEL
DEPEND.
Adjustable
Range
–3dB
:
0dB
:
30dB
:
17
:
63
:
18
:
31
:
02
:
15
:
20
:
31
0
1
:
5
Remarks
Select the master gain from –3, 0, 3, 6,
9, 12, 15, 18, 21, 24, 27, or 30dB.
Set H.DTL LEVEL.
Set V.DTL LEVEL.
Set DTL CORING.
Set a frequency (DTL width) at which
H.DTL is added. The greater the value,
the higher the frequency (the narrower
the DTL).
Set LEVEL DEPEND.
No DTL is added to the portion whose
brightness is the setting value or less.
When the GAMMA MODE SEL item is
set to STD1, each setting value
represents brightness levels, as follows:
0 = about 0%, 1 = about 4%,
2 = about 8%, 3 = about 12%,
SCUFE
MASTER
GAMMA
SCUFE
BLACK
STRETCH
SCUFE
MATRIX
TA B LE
SCUFE
COLOR
0.35
:
0.45
:
0.75
–3
:
OFF
:
+3
OFF
A
B
4 = about 16%, 5 = about 20%.
Set MASTER GAMMA in 0.01 steps.
Set the gamma curb for dark spots.
Select the color correction table.
Set the color correction to ON or OFF.
CORRECTONOFF
SCUFE
<Note>
The items indicated by are the setting items for PAINT
MENU SW() R/W in the <SD CARD R/W SELECT>
screen. The items without are the setting items for PAINT
MENU LEVEL R/W.
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information.
The ____ in the Adjustable Range column indicates the
preset mode.
8
103
Page 7
Chapter 8 Menu Description Tables (continued)
8-3-5 MID SETTING 8-3-6 HIGH SETTING
Items/
Adjustable
Data Saved
MASTER
GAIN
SCUFE
–3dB
:
9dB
:
30dB
H.DTL LEVEL 00
:
14
SCUFE
:
63
V.DTL LEVEL 00
:
15
SCUFE
:
31
DTL CORING 00
:
03
:
SCUFE
15
H.DTL FREQ. 00
:
20
SCUFE
LEVEL
DEPEND.
:
31
0
1
:
5
SCUFE
MASTER
GAMMA
SCUFE
BLACK
STRETCH
SCUFE
MATRIX
TA B LE
SCUFE
COLOR
0.35
:
0.45
:
0.75
–3
:
OFF
:
+3
OFF
A
B
CORRECTONOFF
SCUFE
Range
Remarks
Select the master gain from –3, 0, 3, 6,
9, 12, 15, 18, 21, 24, 27, or 30dB.
Set H.DTL LEVEL.
Set V.DTL LEVEL.
Set DTL CORING.
Set a frequency (DTL width) at which
H.DTL is added. The greater the value,
the higher the frequency (the narrower
the DTL).
Set LEVEL DEPEND.
No DTL is added to the portion whose
brightness is the setting value or less.
When the GAMMA MODE SEL item is
set to STD1, each setting value
represents brightness levels, as follows:
0 = about 0%, 1 = about 4%,
2 = about 8%, 3 = about 12%,
4 = about 16%, 5 = about 20%.
Set MASTER GAMMA in 0.01 steps.
Set the gamma curb for dark spots.
Select the color correction table.
Set the color correction to ON or OFF.
Items/
Adjustable
Data Saved
MASTER
GAIN
SCUFE
–3dB
:
18dB
:
30dB
H.DTL LEVEL 00
:
12
SCUFE
:
63
V.DTL LEVEL 00
:
14
SCUFE
:
31
DTL CORING 00
:
05
:
SCUFE
15
H.DTL FREQ. 00
:
20
SCUFE
LEVEL
DEPEND.
:
31
0
:
3
:
5
SCUFE
MASTER
GAMMA
SCUFE
BLACK
STRETCH
SCUFE
MATRIX
TA B LE
SCUFE
COLOR
0.35
:
0.55
:
0.75
–3
:
OFF
:
+3
OFF
A
B
CORRECTONOFF
SCUFE
Range
Remarks
Select the master gain from –3, 0, 3, 6,
9, 12, 15, 18, 21, 24, 27, or 30dB.
Set H.DTL.
Set V.DTL LEVEL.
Set DTL CORING.
Set a frequency (DTL width) at which
H.DTL is added. The greater the value,
the higher the frequency (the narrower
the DTL).
Set LEVEL DEPEND.
No DTL is added to the portion whose
brightness is the setting value or less.
When the GAMMA MODE SEL item is
set to STD1, each setting value
represents brightness levels, as follows:
0 = about 0%, 1 = about 4%,
2 = about 8%, 3 = about 12%,
4 = about 16%, 5 = about 20%.
Set MASTER GAMMA in 0.01 steps.
Set the gamma curb for dark spots.
Select the color correction table.
Set the color correction to ON or OFF.
104
<Note>
The items indicated by are the setting items for PAINT
MENU SW() R/W in the <SD CARD R/W SELECT>
screen. The items without are the setting items for PAINT
MENU LEVEL R/W.
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information.
The ____ in the Adjustable Range column indicates the
preset mode.
Page 8
Chapter 8 Menu Description Tables (continued)
8-3-7 ADDITIONAL DTL 8-3-8 SKIN TONE DTL
Items/
Data Saved
Adjustable
Range
KNEE APE LVL OFF
1
2
SCUFE
:
5
CHROMA DTL OFF
1
:
SCUFE
5
DTL GAIN(+) –31
:
+00
SCUFE
:
+31
DTL GAIN(–) –31
:
+00
SCUFE
:
+31
DTL CLIP 00
:
SCUFE
63
DTL SOURCE (R+G)/2
(G+B)/2
2G+R+B /4
(3G+R)/4
R
SCUFE
G
H.DTL LINE MIX 0H
1H
SCUFE
CORNER DTL ON
2H
OFF
SCUFE
Remarks
Set KNEE APE LEVEL.
Set the chroma detail.
Detects the chroma edge and
superimposes it on Y to enhance
H.DTL. A greater value increases the
correction.
Adjust the detail level toward +
(upwards).
Adjust the detail level toward the –
(downwards).
Adjust the detail signal clip towards the
+ direction.
Set the signal source for detail signal
components.
Set the scan line to generate the H.DTL
signal.
ON/OFF switching for CORNER DTL
mode, which enhances the resolution
around the screen perimeter.
Items/
Adjustable
Data Saved
SKIN TONE
DTL
ON
OFF
SCUFE
SKIN TONE
ZEBRA
ON
OFF
SCUFE
SKIN DTL
CORING
SCUFE
0
:
5
:
7
SKIN TONE
GET
–––––
Y MAX 000
:
190
SCUFE
:
255
Y MIN 000
:
010
SCUFE
:
255
I CENTER 000
:
022
:
SCUFE
255
I WIDTH 000
:
010
:
SCUFE
255
Q WIDTH 000
:
005
:
SCUFE
255
Q PHASE –128
:
+000
:
SCUFE
+127
Range
Remarks
Set the skin tone DTL to ON or OFF.
ON/OFF switching for ZEBRA within
the SKIN TONE range.
Adjust the effect of SKIN TONE DTL
CORING.
Used when obtaining the target hue for
SKIN TONE DTL. Align the center
marker and the target object with each
other.
Set the maximum value of the
brightness signal to which SKIN TONE
effect is enabled.
8
Set the minimum value of the
brightness signal to which the SKIN
TONE effect is enabled.
Set the center position on the I axis (the
area where SKIN TONE is enabled).
Set the area width where SKIN TONE
is enabled along the I axis above and
below the I CENTER.
Set the area width where SKIN TONE
is enabled along the Q axis above and
below the I CENTER.
Set the phase in the area where SKIN
TONE is enabled based on the Q axis.
Y
Y-MAX
Y-MIN
0
Q-WIDTH
I-CENTER
– direction
R-Y
I-WIDTH
+ direction
Q-PHASE
B-Y
= SKIN TONE AREA
<Note>
The items indicated by are the setting items for PAINT
MENU SW() R/W in the <SD CARD R/W SELECT>
screen. The items without are the setting items for PAINT
MENU LEVEL R/W.
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information.
The ____ in the Adjustable Range column indicates the
preset mode.
105
Page 9
Chapter 8 Menu Description Tables (continued)
8-3-9 KNEE/LEVEL
Items/
Data Saved
MASTER PED –200
SCUFE
MANUAL
KNEE
SCUFE
KNEE POINT 70.0%
SCUFE
KNEE SLOPE 00
SCUFE
WHITE CLIP ON
SCUFE
WHITE CLIP
LV L
SCUFE
A.KNEE POINT 80%
SCUFE
A.KNEE LVL 100
SCUFE
A.KNEE
RESPONSE
SCUFE
<Note>
The items indicated by are the setting items for PAINT
MENU SW() R/W in the <SD CARD R/W SELECT>
screen. The items without are the setting items for PAINT
MENU LEVEL R/W.
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information.
Adjustable
Range
:
+005
:
+200
ON
OFF
:
85.0%
:
107.0%
:
50
:
99 (98)
OFF
90%
:
105%
:
109%
:
85%
:
107%
:
105
:
109
1
:
4
Remarks
Set the master pedestal.
Set the mode when the AUTO KNEE
switch is OFF. The KNEE POINT/
SLOPE set value is enabled when this
setting is ON.
Set the KNEE POINT position in 0.5%
steps.
Set the KNEE SLOPE.
0 setting is equal to KNEE OFF.
<Note>
The adjustable range when using the
AJ-EC3P is from 00 to 98.
Set the WHITE CLIP feature to ON or
OFF. The WHITE CLIP LVL set value is
enabled when this setting is ON.
Set WHITE CLIP LEVEL.
Set the AUTO KNEE POINT position in
0.5% steps. This setting is enabled
when the OUTPUT/AUTO KNEE
selector switch is set to CAM.AUTO
KNEE ON.
Set the AUTO KNEE LEVEL.
Set the AUTO KNEE response speed.
The smaller the setting value, the faster
the response speed.
8-3-10 GAMMA
Items/
Data Saved
MASTER
GAMMA
SCUFE
R GAMMA –15
SCUFE
B GAMMA –15
SCUFE
GAMMA MODE
SEL
SCUFE
Adjustable
Range
0.35
:
0.45
:
0.75
:
+00
:
+15
:
+00
:
+15
STD1
STD2
NEWS
8-3-11 FLARE
Items/
Data Saved
R FLARE 000
SCUFE
G FLARE 000
SCUFE
B FLARE 000
SCUFE
Adjustable
Range
:
100
:
100
:
100
Remarks
Set the master gamma in 0.01% steps.
Set the Rch gamma.
Set the Bch gamma.
Select the gamma.
STD1: Standard gamma feature.
STD2: Gamma feature that conforms to
the ITU-R.BT709 standards.
NEWS
: This video gamma feature can
effectively reproduce gradations
by reducing whiteouts and
blackouts when shooting an
object with partially highlighted
areas. This gamma is especially
effective in the AUTO KNEE
mode.
<Note>
Selecting NEWS gamma disables
settings under the items KNEE SLOPE,
KNEE POINT, and A.KNEE POINT
outlined in [8-3-9 KNEE/LEVEL]. These
settings are also disabled when NEWS
gamma is selected with the USER
switch.
Remarks
Set the R FLARE.
Set the G FLARE.
Set the B FLARE.
106
The ____ in the Adjustable Range column indicates the
preset mode.
Page 10
Chapter 8 Menu Description Tables (continued)
8-4 VF
8-3-12 CAMERA SETTING
Items/
Data Saved
DETAIL ON
SCUFE
2D LPF ON
SCUFE
HIGH COLOR ON
SCUFE
GAMMA ON
SCUFE
TEST SAW ON
SCUFE
FLARE ON
SCUFE
H-F COMPE. ON
SCUFE
ZEBRA Pattern Display
Video Level
109%
ZEBRA 2
DETECT
ZEBRA 1
DETECT
<Note>
All items in CAMERA SETTING are setting targets of the
item PAINT MENU SW() R/W in the <SD CARD R/W
SELECT> screen.
0%
Adjustable
Range
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Remarks
Set the DTL (H, V) to ON or OFF.
ON/OFF switching for the twodimensional LPF that reduces crosscolor.
ON/OFF switching for the HIGH
COLOR mode, which enhances the
color dynamic range.
Set the gamma circuit to ON or OFF.
Switch the test signal ON or OFF.
Set the flare correction to ON or OFF.
ON/OFF switching for the H-F COMPE
mode, which enhances the DTL in the
high-frequency range.
ZEBRA 2
SPOTOFFON
8-4-1 VF DISPLAY
Items/
Data Saved
DISP
CONDITION
–CUFE
DISP MODE 1
–CUFE
VF OUT Y
–CUFE
VF DTL 0
–CUFE
ZEBRA1
DETECT
–CUFE
ZEBRA2
DETECT
–CUFE
ZEBRA2 OFF
–CUFE
LOW LIGHT LVL OFF
–CUFE
ECU MENU
DISP.
–CUFE
50M
INDICATORONOFF
–CUFE
MARKER/CHAR
LV L
–CUFE
Adjustable
Range
NORMAL
HOLD
2
3
NAM
R
G
B
:
3
:
5
0%
:
70%
:
109%
0%
:
85%
:
109%
SPOT
ON
10%
15%
20%
25%
30%
35%
ON
OFF
50%
60%
70%
80%
90%
100%
Remarks
NORMAL
: Display status constantly.
HOLD: Display status only when the
Set the DISP MODE.
Switch the camera’s Warning/Message
indication. Please refer to [4-7-4
Display Modes and Setting Changes/
adjustment Result Messages] for more
information.
Select the VF output.
Y: Brightness signal
NAM: Output signal with the highest
R: Rch signal
G: Gch signal
B: Bch signal
Select the VF DTL.
Additionally enhance the DTL for the
VF signal. 0 setting is the same DTL as
the primary scan lines.
Set the ZEBRA1 detection level (IRE
value).
Set the ZEBRA2 detection level (IRE
value).
Set the ZEBRA2 to ON, OFF, or SPOT.
Set the camera incoming light volume
at which to display LOW LIGNT.
Set the menu display on the VF to ON
or OFF when the ECU is connected.
Set the 50M recording indication to ON
or OFF.
Adjust the brightness of markers and
characters displayed on the VF.
MODE CHECK switch is
pressed.
level among R, G, and B
signals.
8
The ____ in the Adjustable Range column indicates the
preset mode.
107
Page 11
Chapter 8 Menu Description Tables (continued)
8-4-2 VF MARKER
Items/
Data Saved
TA B LE A
–CUFE
CENTER MARK OFF
–CUFE
SAFETY ZONE OFF
–CUFE
SAFETY AREA 80%
–CUFE
FRAME SIG 4:3
–CUFE
FRAME MARK ON
–CUFE
FRAME LVL 0
–CUFE
Adjustable
Range
B
1
2
3
4
1
2
:
90%
:
100%
13:9
14:9
VISTA
OFF
:
15
Select the VF MARKER setting table.
First, select table A or B, then set the
items below for each table.
Switch the center mark.
OFF: Do not display center mark.
1: + (large)
2: Hollow (large)
3: + (small)
4: Hollow (small)
Select the frame type for the safety
zone.
OFF: Do not display frame.
1: Box
2: Corner frame
Set the position of the safety zone.
Set the frame marker.
Only enabled when REC MODE is set
to 16:9.
The VISTA ratio is 16:8.65.
Set the frame marker to ON or OFF.
Set the level outside the frame marker.
0: Equivalent to signal OFF.
15: Same brightness as center area.
8-4-3 USER BOX
Items/
Data Saved
USER BOX ON
–CUFE
USER BOX
WIDTH
–CUFE
USER BOX
HEIGHT
–CUFE
USER BOX H
POS
–CUFE
USER BOX V
POS
–CUFE
Adjustable
Range
OFF
1
:
13
:
100
1
:
13
:
121
–50
:
+00
:
+50
–121
:
+000
:
+121
Select whether or not to display the
USER BOX.
Set the width of the USER BOX.
Set the height of the USER BOX.
Set the horizontal position of the USER
BOX.
Set the vertical position of the USER
BOX.
Remarks
This setting, however, is disabled if
the FRAME SIG is set to VISTA.
Remarks
8-4-4 VF INDICATOR1
Items/
Data Saved
EXTENDER ON
–CUFE
SHUTTER ON
–CUFE
FILTER ON
–CUFE
WHITE ON
–CUFE
GAIN ON
–CUFE
IRIS OFF
–CUFE
CAMERA ID OFF
–CUFE
ID POSITION UPPER R
–CUFE
DATE/TIME ON
–CUFE
ZOOM LVL ON
–CUFE
COLOR TEMP ON
–CUFE
The ____ in the Adjustable Range column indicates the
preset mode.
Adjustable
Range
OFF
OFF
OFF
OFF
OFF
IRIS
S+IRIS
S
BAR
CAM
ALWAYS
UPPER L
LOWER R
LOWER L
OFF
OFF
OFF
Remarks
Set the extender indication to ON or
OFF.
Set the shutter speed indication to ON
or OFF.
Set the filter No. indication to ON or
OFF.
Set the AWB PRE/A/B indication to ON
or OFF.
Set to ON or OFF the indications for
current gain setting, S.GAIN.
OFF: Disable indications of both the
super iris ON status and the iris
value.
IRIS: Enable only the iris value
indication.
S+IRIS
: Enables indications of the super
iris ON status and the iris value.
S: Enable indication of the super
iris ON status.
(The iris value indication and the iris
override indication/non indication are
interlocked.)
Select when to enable the ID mix during
recording.
OFF: Disable ID mix.
BAR: Enable when recording color
CAM: Enable when recording
ALWAYS
<Note>
ID MIX INH of the “8-9-1 OPTION” is
set to OFF to mix an ID to the camera
image.
ID is not superimposed in the EE mode,
but recorded onto the P2 card.
Set the camera ID recording position.
UPPER R
UPPER L
LOWER R
LOWER L
Select whether or not to simultaneously
mix the year/month/date and hour/
minute/second when recording the
camera ID.
Set the zoom position indication to ON
or OFF.
Set the color temperature indication to
ON or OFF.
bars.
camera image.
: Enable always.
: Upper right.
: Upper left.
: Lower right.
: Lower left.
108
Page 12
Chapter 8 Menu Description Tables (continued)
8-4-5 VF INDICATOR2
Items/
Data Saved
P2CARD
REMAIN
–CUFE
BATTERY ON
–CUFE
AUDIO LVL ON
–CUFE
TC OFF
–CUFE
SYSTEM INFO OFF
–CUFE
SAVE LED P2CARD
–CUFE
DV ON
–CUFE
VOICEMEMO ON
–CUFE
Adjustable
Range
OFF
ONE-CARD
TOTAL
OFF
OFF
TCG
TCR
TCG/TCR
ALWAYS
NORMAL
SAVE
OFF
OFF
Remarks
Select the indication mode for the P2
card’s remaining capacity.
OFF: Disable the remaining capacity
indication.
ONE-CARD:
Display the remaining capacity
of the P2 card currently used for
recording.
TOTAL
: Display the total remaining
capacity of all P2 cards in slots.
Set the battery voltage indication to ON
or OFF.
Set the audio lever meter indication to
ON or OFF.
Select the time code to display.
OFF: Disable the time code display.
TCG: Display the time code generator
value in E-E mode.
TCR: Display the time code reader
value in V-V mode.
TCG/TCR:
Display the time code generator
value in E-E mode, and the time
code reader value in V-V mode.
Select the method of displaying system
information and warnings.
OFF: Display no warnings other than
“TURN POWER OFF” and
“SYSTEM ERROR”.
ALWAYS:
Always display warnings.
NORMAL:
Display warnings for 3 seconds only
when problems occur.
Set the SAVE lamp function.
P2CARD:
The lamp blinks in synch with
the warning message when the
P2 card’s remaining recording
capacity is getting low.
SAVE: The lamp lights up when the
SAVE ON/OFF switch is set to
ON and the output system
assigned in [8-2-2 OPTION
MODE] is in the save mode.
DV Select whether or not to enable DV
indication when the format is set to DV.
ON: Enable DV indication.
OFF: Disable DV indication.
Select whether or not to enable the
indication during voice memo
recording.
ON: Enable indication.
OFF: Disable indication.
V
V
V
Items/
Data Saved
REC STATUS ON
–CUF–
PROXY REC ON
–CUF–
Adjustable
Range
OFF
OFF
Remarks
Select whether or not to enable “REC”
indication in the viewfinder and on the
LCD monitor during recording.
ON: REC indication enabled.
OFF: REC indication not enabled.
<Note>
This option is useful when the AJSPC700P is used independently. When
the 1394 control option is set to BOTH
with an external IEEE 1394 device,
settings are subject to setting of the
menu option REC TALLY in SYSTEM
MODE.
When a video encoder card (AJYAX800G, optional) is attached, proxy
recording information is displayed when
recording starts.
ON: Display indicating whether proxy
recording is to be performed on
the P2 card only, or on both the
P2 card and the SD memory card.
OFF: Proxy recording information is not
displayed.
8-4-6 MODE CHECK IND
Items/
Data Saved
STATUS ON
–CUFE
!LED ON
–CUFE
FUNCTION ON
–CUFE
AUDIO ON
–CUFE
P.ON IND ON
–CUFE
The ____ in the Adjustable Range column indicates the
preset mode.
Adjustable
Range
OFF
OFF
OFF
OFF
OFF
Remarks
Select whether or not to display the
status indication during MODE CHECK.
Select whether or not to display the
cause indication screen when the ! LED
turns on during MODE CHECK
Select whether or not to display the
FUNCTION indication screen during
MODE CHECK.
Select whether or not to display the
AUDIO indication screen during MODE
CHECK.
Select whether or not to display the
status indication screen after the power
is turned ON.
8
109
Page 13
Chapter 8 Menu Description Tables (continued)
8-5 CAM OPERATION
8-4-7 !LED
Items/
Data Saved
GAIN(0dB) ON
–CUFE
GAIN (-3dB) ON
–CUFE
SHUTTER ON
–CUFE
WHITE
PRESET
–CUFE
EXTENDER ON
–CUFE
BLACK STR ON
–CUFE
MATRIX ON
–CUFE
COLOR
CORRECTIONONOFF
–CUFE
FILTER ON
–CUFE
SUPER V ON
–CUFE
50M/25M/DV OFF
–CUFE
AT W
–CUFE
<Note>
If both GAIN (0 dB) and GAIN (–3 dB) are set to ON, the
LED illuminates except when GAIN is adjusted to 0 dB and
–3 dB.
Adjustable
Range
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
W/O 50M
W/O 25M
W/O DV
ON
OFF
Remarks
Select whether or not to illuminate
when GAIN is set to other than 0 dB.
Select whether or not to illuminate
when GAIN is set to other than –3 dB.
Select whether or not to illuminate
when the shutter is set to ON.
Select whether or not to illuminate
when the WHITE BAL switch is set to
PRST.
Select whether or not to illuminate
when the lens is in EXTENDER mode.
Select whether or not to illuminate
when BLACK STRETCH is used.
Select whether or not to illuminate
when MATRIX is set to ON.
Select whether or not to illuminate
when COLOR CORRECTION is set to
ON.
Select whether or not to illuminate the
lamp when filter1 (3200K) is not 3200K.
Select whether or not to illuminate
when SUPER V is set to ON.
Select whether or not to illuminate
according to the recording mode.
OFF: Does not illuminate in any
recording mode.
W/O 50M:
Illuminate except in DVCPRO50
mode.
W/O 25M:
llluminate except in DVCPRO
mode.
W/O DV:
Illuminate except in DV mode.
Select whether or not to illuminate
when auto-tracking white balance is
allocated to the WHITE BAL switch B.
8-5-1 CAMERA ID
Items/
Data Saved
ID1
–CUF–
ID2
–CUF–
ID3
–CUF–
<Note>
This setting is canceled when READ FACTORY DATA is
selected.
Adjustable
Range
Remarks
Setting 1 for the CAMERA ID recorded
on color bars. Up to 10 characters are
allowed for this setting.
Setting 2 for the CAMERA ID recorded
on color bars. Up to 10 characters are
allowed for this setting.
Setting 3 for the CAMERA ID recorded
on color bars. Up to 10 characters are
allowed for this setting.
8-5-2 SHUTTER SPEED
Items/
Data Saved
SYNCHRO
SCAN
–CUFE
SUPER V ON
–CUFE
POSITION1 ON
–CUFE
POSITION2 ON
–CUFE
POSITION3 ON
–CUFE
POSITION4 ON
–CUFE
POSITION5 ON
–CUFE
POSITION6 ON
–CUFE
Adjustable
Range
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Remarks
Allocate SYNCHRO SCAN as a shutter
speed selectable by the shutter switch.
Allocate SUPER V as a shutter speed
selectable by the shutter switch.
Allocate the shutter speed set by
POSITION1 SELECT in the
<SHUTTER SELECT> screen as the
shutter speed selectable by the shutter
switch.
Allocate the shutter speed set by
POSITION2 SELECT in the
<SHUTTER SELECT> screen as the
shutter speed selectable by the shutter
switch.
Allocate the shutter speed set by
POSITION3 SELECT in the
<SHUTTER SELECT> screen as the
shutter speed selectable by the shutter
switch.
Allocate the shutter speed set by
POSITION4 SELECT in the
<SHUTTER SELECT> screen as the
shutter speed selectable by the shutter
switch.
Allocate the shutter speed set by
POSITION5 SELECT in the
<SHUTTER SELECT> screen as the
shutter speed selectable by the shutter
switch.
Allocate the shutter speed set by
POSITION6 SELECT in the
<SHUTTER SELECT> screen as the
shutter speed selectable by the shutter
switch.
110
The ____ in the Adjustable Range column indicates the
preset mode.
Page 14
Chapter 8 Menu Description Tables (continued)
8-5-3 SHUTTER SELECT 8-5-4 USER SW
Items/
Data Saved
SUPER V
MODE
–CUFE
POSITION1
SEL
–CUFE
POSITION2
SEL
–CUFE
POSITION3
SEL
–CUFE
POSITION4
SEL
–CUFE
POSITION5
SEL
–CUFE
POSITION6
SEL
–CUFE
Adjustable
Range
FRM1
FRM2
1/100
1/120
1/250
1/500
1/1000
1/2000
1/100
1/120
1/250
1/500
1/1000
1/2000
1/100
1/120
1/250
1/500
1/1000
1/2000
1/100
1/120
1/250
1/500
1/1000
1/2000
1/100
1/120
1/250
1/500
1/1000
1/2000
1/100
1/120
1/250
1/500
1/1000
1/2000
Remarks
Select the SUPER V switching mode.
FRM1: Normal mode.
FRM2: After-image reduction mode.
<Note>
The SUPER V mode increases vertical
resolution by directly outputting the
photo-diode vertical signal from the
CCD. FRM1 sets the accumulation level
to 1/30th second. FRM sets the level to
1/60th second, reducing sensitivity by
half.
Select the shutter speed to be allocated
to POSITION1.
Select the shutter speed to be allocated
to POSITION2.
Select the shutter speed to be allocated
to POSITION3.
Select the shutter speed to be allocated
to POSITION4.
Select the shutter speed to be allocated
to POSITION5.
Select the shutter speed to be allocated
to POSITION6.
Items/
Data Saved
USER MAIN SW INH
–CUFE
USER1 SW INH
–CUFE
USER2 SW INH
–CUFE
Adjustable
S.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
AT W
Y GET
NEWS-G.
AUDIO CH1
AUDIO CH2
REC SW
RET SW
SLOT SEL
PRE REC
USB
S.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
AT W
Y GET
NEWS-G.
AUDIO CH1
AUDIO CH2
REC SW
RET SW
SLOT SEL
PRE REC
USB
S.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
AT W
Y GET
NEWS-G.
AUDIO CH1
AUDIO CH2
REC SW
RET SW
SLOT SEL
PRE REC
USB
Range
Remarks
Allocate the USER MAIN button.
Allocate the USER1 button.
8
Allocate the USER2 button.
<Note>
For each function of the USER switches, refer to [4-9-4
Assigning Functions to USER MAIN, USER1 and USER2
Buttons].
The ____ in the Adjustable Range column indicates the
preset mode.
111
Page 15
Chapter 8 Menu Description Tables (continued)
8-5-5 SW MODE 8-5-6 WHITE BALANCE MODE
Items/
Data Saved
RET SW REC
–CUFE
S.BLK LVL OFF
–CUFE
AUTO KNEE SWON
SCUFE
SHD,ABB SW
CTL
–CUFE
COLOR BARS SMPTE
–CUFE
S.GAIN OFF L/M/H
–CUFE
ECU DATA
SAVE
–CUF–
ECU REC CHK SWR.REVIEW
–CUFE
Adjustable
Range
CHECK
CAM RET
–10
–20
–30
OFF
ON
OFF
FULL
BARS
SPLIT
ARIB
S.GAIN
ON
OFF
PLAY
Remarks
Select the RET switch function.
REC CHECK:
Perform REC REVIEW.
CAM RET:
Perform return signal output.
Set the super black level.
Select whether or not to use the AUTO
KNEE switch.
Select whether or not to enable the
automatic black shading adjustment if
the ABB switch has been pressed for 5
seconds or more.
Select the color bars to use.
SMPTE: Use the SMPTE color bars.
FULL BARS:
SPLIT: Use SPLIT color bars.
ARIB: Use ARIB multi-format
Select when the SUPER GAIN mode is
disabled.
L/M/H
S.GAIN
ON: Store the values set and adjusted
OFF: Does not store camera-related
Select the camera-recorder operation
to be performed when the ECU REC
CHECK button is pressed.
R.REVIEW
PLAY: Play back the most-recently
Use full color bars.
color bars.
: Disabled when the gain selector
switch is operated.
: Disabled only with the S.GAIN
switch (USER button).
with the ECU when the ECU is
disconnected from the camerarecorder.
set values.
: Perform REC REVIEW.
recorded clip from the
beginning.
Items/
Data Saved
FILTER INH ON
–CUFE
SHOCKLESS
AWB
–CUFE
AWB AREA 25%
–CUFE
AWB & ABB
OFFSET
–CUFE
COLOR TEMP
PRE
–CUFE
AWB A MEM
–CUFE
COLOR TEMP A3200K
–CUFE
AWB B MEM
–CUFE
COLOR TEMP B3200K
–CUFE
ATW SPEED NORMAL
–CUFE
Adjustable
Range
OFF
OFF
FAS T
NORMAL
SLOW1
SLOW2
SLOW3
50%
90%
ON
OFF
3200K
:
5600K
VAR
:
5600K
VAR
AT W
:
5600K
SLOW
FAS T
Remarks
Select whether or not to retain white
balance memory (A/B) data for
individual filters.
ON: Retain data in the A/B memory (2
memory areas) regardless of the
filters.
OFF: Retain data for individual filters.
Set SHOCKLESS AWB to ON (FAST/
NORMAL/SLOW1-3) or OFF.
SHOCKLESS AWB eliminates the
shock caused by switching the WHITE
BAL switch’s PRST/A/B setting. The
switching time can also be selected.
Switch the AWB detection area.
25%:Detect 25% of area around the
screen center.
50%:Detect 50% of area around the
screen center.
90%:Detect 90% of area in the full
screen.
Select whether or not to reset the GAIN
and PED values in the ROP menu
when AWB and ABB are executed.
ON: Do not reset.
OFF: Reset values.
Set the AWB PRE color temperature.
Select the function to be allocated to
WHITE BAL switch A.
MEM: Function to store values set by
executing the auto white
balance.
VAR: Function to apply color
temperature set by COLOR
TEMP A.
Set the color temperature when VAR is
selected under AWB A.
Select the function to be allocated to
WHITE BAL switch B.
MEM: Function to store values set by
executing auto white balance.
VAR: Function to apply color
temperature set by COLOR
TEMP B.
ATW : Function to execute auto-
tracking white balance.
Set the color temperature when VAR is
selected under AWB B.
Select the control speed for the autotracking white balance.
112
The ____ in the Adjustable Range column indicates the
preset mode.
Page 16
Chapter 8 Menu Description Tables (continued)
8-6 MAIN OPERATION
8-5-7 USER SW GAIN
Items/
Data Saved
S.GAIN
30 dB
–CUFE
36 dB
–CUFE
Adjustable
Range
_
•
_
•
Select whether or not to enable 30dB
for SUPER GAIN.
_: Enable.
• : Disable.
Select whether or not to enable 36dB
for SUPER GAIN.
_: Enable.
• : Disable.
8-5-8 IRIS
Items/
Data Saved
A.IRIS LEVEL 000
–CUFE
A.IRIS PEAK/
AVE
–CUFE
A.IRIS MODE NORM1
–CUFE
S.IRIS LEVEL 000
–CUFE
IRIS GAIN CAM
–CUFE
IRIS GAIN
VAL UE
–CUFE
Adjustable
Range
:
050
:
100
000
:
040
:
100
NORM2
CENTR
:
080
:
100
LENS
01
:
08
:
20
Set the target value for auto iris.
Determine the peak-to-standard ratio
for the auto iris.
A larger value sets the auto iris to
respond to the peak in the IRIS
detection window, while a smaller value
sets it to respond to the average value
in the window.
Select the auto iris detection window.
NORM1
NORM2
CENTR
Set the target value for the super iris.
Select which unit controls IRIS GAIN.
<Note>
Lenses with an extender, such asC2,
C0.8 sold before FUJINON DIGI
POWER, perform IRIS compensation
while enabling the extender. Therefore,
if this setting is switched to CAM, the
camera’s iris control will not operate
properly.
Set the adjustable value for IRIS GAIN.
This setting is effective when CAM is
selected for IRIS GAIN.
Remarks
Remarks
:The window closer to the center
of the screen.
:The window closer to bottom of
the screen.
:The spot window in the center of
the screen.
8-6-1 BATTERY/P2CARD
Items/
Data Saved
BATTERY
SELECT
–CUF–
EXT DC IN
SELECT
–CUF–
BATT NEAR
END ALARMONOFF
–CUF–
BATT NEAR
END CANCEL
–CUF–
BATT END
ALARM
–CUF–
BATT REMAIN
FULL
–CUF–
Adjustable
Range
PRO14
TRIM14
HYTRON50
HYTRON100
HYTRON120
DIONIC90
DIONIC160
HP-90L
BP-H120
NP-L50
ENDURA50
ENDURA80
BP-L60/90
NiCd14
NiCd13
NiCd12
TYPE A
TYPE B
AC_ADPT
PRO14
TRIM14
HYTRON50
HYTRON100
HYTRON120
DIONIC90
DIONIC160
HP-90L
BP-H120
NP-L50
ENDURA50
ENDURA80
BP-L60/90
NiCd14
NiCd13
NiCd12
TYPE A
TYPE B
ON
OFF
ON
OFF
70%
100%
Select the battery to use. Remaining
capacity detection is also performed
according to the selected battery.
The selectable battery types change
depending on the settings under [8-6-2
BATTERY SETTING1] and [8-6-3
BATTERY SETTING2].
Set the remaining capacity detection
type when a battery is connected to the
DC IN connector. Remaining capacity
detection is also performed according
to the selected battery type.
The selectable battery types change
depending on the settings under [8-6-2
BATTERY SETTING1] and [8-6-3
BATTERY SETTING2].
<Note>
The % display is disabled even when a
digital battery is connected to the DC IN
connector.
Select whether or not to set the alarm
to beep for BATT NEAR END ALARM.
If set to ON, the warning tone and
indication can be canceled by pressing
the MODE CHECK button when BATT
NEAR END ALARM is triggered.
Select whether or not to set the alarm
to beep for BATT END ALARM.
Set the display content of the remaining
battery capacity indicator bars in the
display window when using a digital
battery.
70%: Indicate FULL at 70% capacity.
100%
: Indicate FULL at 100% capacity.
Remarks
8
The ____ in the Adjustable Range column indicates the
preset mode.
113
Page 17
Chapter 8 Menu Description Tables (continued)
8-6-2 BATTERY SETTING1
Items/
Adjustable
Data Saved
CARD NEAR
END ALARMONOFF
–CUF–
CARD NEAR
END TIME
2min
3min
–CUF–
CARD END
ALARM
ON
OFF
–CUF–
CARD REMAIN/3min/
5min/
–CUF–
Range
Remarks
Select whether or not to set the alarm
to beep for P2 CARD NEAR END
ALARM.
Set the remaining time to indicate the
P2 CARD NEAR END TIME alarm.
Select whether or not to set the alarm
to beep for P2 CARD END ALARM.
Set the length of time for one segment
() of the P2 card’s remaining capacity
indicator bars.
3min/: One segment represents 3
minutes.
5min/: One segment represents 5
minutes.
Items/
Data Saved
PRO14
–CUF–
TRIM14
–CUF–
HYTRON50
–CUF–
HYTRON100
–CUF–
HYTRON120
–CUF–
Adjustable
Range
_
•
MANUAL
AUTO
11.0
:
13.9
:
15.0
_
•
MANUAL
AUTO
11.0
:
13.6
:
15.0
_
•
MANUAL
AUTO
11.0
:
13.1
:
15.0
_
•
MANUAL
AUTO
11.0
:
13.2
:
15.0
_
•
MANUAL
AUTO
11.0
:
13.1
:
15.0
Remarks
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the
above menu, set the NEAR END
voltage in 0.1 V steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
114
The ____ in the Adjustable Range column indicates the
preset mode.
Page 18
Chapter 8 Menu Description Tables (continued)
Items/
Data Saved
DIONIC90
–CUF–
DIONIC160
–CUF–
HP-90L
–CUF–
BP-H120
–CUF–
NP-L50
–CUF–
Adjustable
Range
_
•
MANUAL
AUTO
11.0
:
13.6
:
15.0
_
•
MANUAL
AUTO
11.0
:
13.3
:
15.0
_
•
MANUAL
AUTO
11.0
:
12.8
:
15.0
_
•
MANUAL
AUTO
11.0
:
11.5
:
15.0
_
•
MANUAL
AUTO
11.0
:
13.3
:
15.0
Remarks
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
Items/
Data Saved
ENDURA50
–CUF–
ENDURA80
–CUF–
BP-L60/90
–CUF–
Adjustable
Range
_
•
MANUAL
AUTO
11.0
:
13.1
:
15.0
_
•
MANUAL
AUTO
11.0
:
13.5
:
15.0
_
•
MANUAL
AUTO
11.0
:
11.2
:
15.0
Remarks
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Select auto or manual to set the NEAR
END voltage.
MANUAL
: Set voltage manually.
AUTO: Set voltage automatically.
When MANUAL is selected in the menu
above, set the NEAR END voltage in
0.1 V steps.
<Note>
The remaining battery capacity for digital batteries is
displayed as % inside the viewfinder (PRO14/TRIM14/
HYTRON50/HYTRON100/HYTRON120/DIONIC90/
DIONIC160/NP-L50/ENDURA50/ENDURA80).
The BATT NEAR END alarm, however, is triggered
according to the setting on the <BATTERY SETTING1>
screen, regardless of the % indication.
The ____ in the Adjustable Range column indicates the
preset mode.
8
115
Page 19
Chapter 8 Menu Description Tables (continued)
8-6-3 BATTERY SETTING2 8-6-4 MIC/AUDIO1
Items/
Data Saved
NiCd14
NEAR END 11.0
END 11.0
–CUF–
NiCd13
NEAR END 11.0
END 11.0
–CUF–
NiCd12
NEAR END 11.0
END 11.0
–CUF–
TYPE A
FULL 12.0
NEAR END 11.0
END 11.0
–CUF–
TYPE B
FULL 12.0
NEAR END 11.0
END 11.0
–CUF–
Adjustable
Range
_
•
:
13.6
:
15.0
:
13.2
:
15.0
_
•
:
12.7
:
15.0
:
12.2
:
15.0
_
•
:
11.5
:
15.0
:
11.2
:
15.0
_
•
:
15.0
:
17.0
:
13.6
:
15.0
:
13.2
:
15.0
_
•
:
13.5
:
17.0
:
11.8
:
15.0
:
11.1
:
15.0
Remarks
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Set the NEAR END voltage in 0.1 V
steps.
When MANUAL is selected in the menu
above, set the END voltage in 0.1 V
steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Set the NEAR END voltage in 0.1 V
steps.
When MANUAL is selected in the menu
above, set the END voltage in 0.1 V
steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Set the NEAR END voltage in 0.1 V
steps.
When MANUAL is selected in the menu
above, set the END voltage in 0.1 V
steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Set the voltage to display the FULL
indication in 0.1 V steps.
Set the NEAR END voltage in 0.1 V
steps.
When MANUAL is selected in the menu
above, set the END voltage in 0.1 V
steps.
Enable selection under BATTERY
SELECT.
_:Enable selection.
• :Disable selection.
Set the voltage to display the FULL
indication in 0.1 V steps.
Set the NEAR END voltage in 0.1 V
steps.
When MANUAL is selected in the menu
above, set the END voltage in 0.1 V
steps.
Items/
Data Saved
FRONT VR CH1 OFF
Adjustable
Range
FRONT
W.L .
REAR
ALL
Remarks
Select whether or not to enable the
FRONT AUDIO LEVEL control for the
signal selected as the input signal to
AUDIO CH1.
OFF: Disabled for any input selected.
Recording level does not
change by turning the volume
control.
FRONT
: Only enabled when FRONT is
selected.
W.L .: Only enabled when WIRELESS
is selected.
REAR:Only enabled when REAR is
selected.
ALL: Enabled for any input selected. –CUF–
FRONT VR CH2 OFF
FRONT
W.L .
REAR
ALL
Select whether or not to enable the
FRONT AUDIO LEVEL control for the
signal selected as an input signal to
AUDIO CH2.
OFF: Disabled for any input selected.
Recording level does not
change by turning the volume
control.
FRONT
: Only enabled when FRONT is
selected.
W.L .: Only enabled when WIRELESS
is selected.
REAR:Only enabled when REAR is
selected.
ALL: Enabled for any input selected. –CUF–
MIC LOWCUT
CH1
OFF
FRONT
Select the microphone low-cut filter.
W.L .
–CUF–
MIC LOWCUT
CH2
REAR
OFF
FRONT
Select the microphone low-cut filter.
W.L .
–CUF–
LIMITER CH1 ON
REAR
Select the limiter.
OFF
–CUF–
LIMITER CH2 ON
Select the limiter.
OFF
–CUF–
25M REC CH
SEL
2CH
4CH
Select the audio channels to be
recorded in the DVCPRO and DV
formats.
2CH: Only recorded in CH1 and CH2.
4CH: Recorded in all channels from
–CUF–
TEST TONE OFF
NORMAL
ALWAYS
CHSEL
CH1 to CH4.
Select the test signal.
OFF: Disable test tone output.
NORMAL
: Output test tones to CH1/2
when the OUTPUT/AUTO
KNEE selector switch is set to
BARS and the AUDIO IN
switch CH1 is set to FRONT.
ALWAYS:Output test tones to CH1/2 when
OUTPUT/AUTO KNEE selector
switch is set to BARS.
CHSEL
: Output test tone to the
channels where the AUDIO
IN switch CH1 or CH2 is set
to FRONT when OUTPUT/
AUTO KNEE selector switch
is set to BARS. The test tone
–CUF–
is not output to CH3 and CH4.
The ____ in the Adjustable Range column indicates the
preset mode.
116
Page 20
Chapter 8 Menu Description Tables (continued)
8-6-5 MIC/AUDIO2 8-6-6 TC/UB
Items/
Data Saved
FRONT MIC
POWER
–CUF–
REAR MIC
POWER
–CUF–
AUDIO O UT ON
–CUF–
MONITOR
SELECT
–CUF–
FRONT MIC
LEVEL
–CUF–
REAR MIC CH1
LV L
–CUF–
REAR MIC CH2
LV L
–CUF–
REAR LINE IN
LV L
–CUF–
AUDIO O UT LVL – 3dB
–CUF–
HEADROOM 18dB
–CUF–
WIRELESS
WARN
–CUF–
Adjustable
Range
ON
OFF
ON
OFF
OFF
STEREO
MIX
–40dB
–50dB
–50dB
–60dB
–50dB
–60dB
–3dB
0dB
+4dB
0dB
+4dB
20dB
ON
OFF
Remarks
Select the phantom power supply for
the front microphone.
Select the phantom power supply for
the rear microphone.
Set the audio output circuit.
OFF: Power-down output circuit to
disable output.
ON: Enable output.
Select the signal format for output to
the PHONE (earphones) jack.
Select the front microphone input level.
Select the rear microphone input level.
Select the rear microphone input level.
Select the rear line input level.
Select the audio output level.
Set the headroom (standard level).
Select whether or not to enable the
alarm to trigger for poor wireless
receiver reception.
Items/
Data Saved
TC MODE DF
–CUF–
UB MODE USER
–CUF–
VITC UB MODE USER/EXT
–CUF–
TCG SET HOLD ON
–CUF–
Adjustable
Range
NDF
TIME
DATE
EXT
TCG
FRM RATE
REGEN
TIME
DATE
TCG
FRM RATE
REGEN
OFF
Remarks
Set the time code mode.
DF: Drop frame.
NDF: Non drop frame.
Select the user bits mode.
USER:Select UB value set in the LCD
section.
TIME: Select local time (hours,
minutes, seconds).
DATE: Select local date and time (2 last
digits of year, month, date,
time).
EXT: When “CAM” or “VIDEO” is
selected in the menu option
REC SIGNAL in the SYSTEM
MODE screen, user’s bit input to
the TC IN connector is the
reference.
When “1394” is selected, user’s
bit input to the DVCPRO/DV
connector is the reference.
If reading fails, USER value is
retained.
TCG: TCG value enters UB.
FRM RATE:
Select same camera shoting
information (frame rate, etc.) with
the VAUX UB (VITC UB).
REGEN
:Read out value stored in the
card and record value
continuously.
Select the user bits mode for VAUX TC
(VITC).
USER/EXT:
If UB MODE is set to EXT, the
EXT value is recorded. If not,
USER value set by UB is
recorded.
TIME: Select local time (hours,
minutes, seconds).
DATE: Select local date and time (2 last
digits of year, month, date,
time).
TCG: TCG value enters UB.
FRM RATE:
Select same camera shoting
information (frame rate, etc.) with
the VAUX UB (VITC UB).
REGEN
:Read out value stored in card
and record value continuously.
ON/OFF switching for the feature that
always starts recording (when the
power is turned ON again) the TCG
value that was set before the power is
turned OFF.
8
The ____ in the Adjustable Range column indicates the
preset mode.
117
Page 21
Chapter 8 Menu Description Tables (continued)
8-7 FILE
8-7-1 SD CARD READ/WRITE
Items/
Data Saved
FIRST REC TC PRESET
–CUF–
P.OFF LCD
DISPLAY
–CUF–
TC OUT TCG
–CUF–
Adjustable
Range
REGEN
ON
OFF
TCG/TCR
Remarks
For the first recording after the power is
turned on, a P2 card is inserted and
then switching from this P2 card to
another recording-target P2 card is
performed, select whether or not to
regenerate the time code as the value
on the new P2 card.
PRESET:
Use the camera-recorder’s internal
time code.
REGEN:
For clips recorded on the
recording-target P2 card,
regenerate the time code as the
time code of the clip that has the
most recent date and time.
<Note>
Set the date and time accurately. For
guidance on setting, see [4-5-2 Setting
the Internal Clock’s Date and Time].
Select whether or not to display the
time code setting and counter
indication on the LCD monitor when the
power is turned OFF.
ON: Display setting and indication
while the power is turned OFF.
OFF: Power-down LCD monitor while
camera power is turned OFF.
Setting and indication disabled.
Select the time code to be output to the
time code output connector.
TCG:Always output time code
generator value.
TCG/TCR:
Display time code generator value
in E-E mode, and time code
reader value in V-V mode.
Items/
Data Saved
R.SELECT 1
–––F–
READ
–––––
W.S ELEC T 1
–––F–
WRITE
–––––
CARD CONFIG
–––––
TITLE READ
–––––
TITLE1-8:
–––––
Adjustable
Range
:
8
:
8
Remarks
Select the file number to read out.
Read out the data from the SD memory
card.
Select the file number to write in.
Write the camera-recorder’s menu data
to the SD memory card.
Format the SD memory card.
Read out the title of the data recorded
on the SD memory card.
Up to 8 letters can be set for the title
name.
The ____ in the Adjustable Range column indicates the
preset mode.
8-6-7 UMID SET/INFO
Items/
Data Saved
COUNTRY NO-INFO
–CUF–
ORGANIZATION
–CUF–
USER NO-INFO
–CUF–
DEVICE NODE
–––––
<Note>
Please refer to [4-5-6 Setting UMID Information] for the
UMID information setting.
Adjustable
Range
NO-INFO
Remarks
Input the user’s country. NO-INFO is
displayed until the input completes.
Input the user’s organisation or
company name. NO-INFO is displayed
until the input completes.
Input the user name. NO-INFO is
displayed until the input completes.
Indicate the product ID number.
118
Page 22
Chapter 8 Menu Description Tables (continued)
8-7-2 SD CARD R/W SELECT 8-7-3 LENS FILE
Items/
Data Saved
ID READ/
WRITE
–––F–
USER MENU
SELECT R/W
–––F–
SYSTEM MENU
R/W
–––F–
PA I N T M E N U
LEVEL R/W
–––F–
PA I N T M E N U
) R/WONOFF
SW(
–––F–
PA I N T ( F L A R E)
R/W
–––F–
VF MENU
R/W
–––F–
CAM OPE
MENU R/W
–––F–
MAIN OPE
MENU R/W
–––F–
MAINTE MENU
R/W
–––F–
Adjustable
Range
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Remarks
Select whether or not to include the
CAMERA ID when reading out or
writing to the SD memory card.
Select whether or not to include the
FILE MENU settings when reading out
or writing to the SD memory card.
Select whether or not to include the set
values on the SYSTEM SETTING page
when reading out or writing to the SD
memory card.
Select whether or not to include the
adjusted values on the PAINT page
when reading out or writing to the SD
memory card.
Select whether or not to include the set
values on the PAINT MENU page when
reading out or writing to the SD
memory card.
Select whether or not to include the set
values on the FLARE page when
reading out or writing to the SD
memory card.
Select whether or not to include the set
values on the VF page when reading
out or writing to the SD memory card.
Select whether or not to include the set
values on the CAM OPERATION page
when reading out or writing to the SD
memory card.
Select whether or not to include the set
values on the MAIN OPERATION page
when reading out or writing to the SD
memory card.
Select whether or not to include the set
values on the MAINTENANCE page
when reading out or writing to the SD
memory card.
Items/
Data Saved
FILE NO. 1
–––––
READ
–––––
WRITE
–––––
TITLE1-8
–––––
Adjustable
Range
:
8
8-7-4 SCENE
Items/
Data Saved
READ USER
DATA
–––––
SCENE SEL 1
–––––
READ
–––––
WRITE
–––––
RESET
–––––
TITLE 1-4
–––––
Adjustable
Range
:
4
Remarks
Select the lens file number.
Read the lens file data.
Write the lens file data.
Up to 12 letters can be set for the title
name.
8
Remarks
Read out the data from the user area in
the memory.
Select the scene file.
Read the scene file.
Write the scene file.
Reset the scene file values to the initial
values.
Create the scene file title.
8-7-5 INITIALIZE
Items/
Data Saved
READ
FACTORY DATA
–––––
WRITE USER
DATA
–––––
RESET LENS
FILES
–––––
The ____ in the Adjustable Range column indicates the
preset mode.
Adjustable
Range
Remarks
The menu (USER MENU, MAIN MENU,
OPTION MENU) values are all reset to
factory settings.
Save the user preference menu data in
the camera’s internal memory.
Reset the lens file data to the factory
settings.
119
Page 23
Chapter 8 Menu Description Tables (continued)
8-8 MAINTENANCE
8-8-1 SYSTEM CHECK
Items/
Data Saved
COLOR CHECK ON
–––––
Adjustable
Range
OFF
ON/OFF switching for checking proper
operation of the camera-recorder.
Displays the center Y and RGB levels
on the viewfinder to indicate whether
the signals have been properly
processed and transmitted from the
optical system to the digital system.
8-8-2 LENS ADJ
Items/
Data Saved
F2.8 ADJ ON
–––––
F16 ADJ ON
–––––
Adjustable
Range
OFF
OFF
The iris is only set to F2.8 when this
item set to ON.
The iris is only set to F16 when this
item set to ON.
8-8-3 BLACK SHADING
Remarks
Remarks
8-8-5 DIAGNOSTIC1
Items/
Data Saved
CAMSOFT(IN)
–––––
CAMSOFT
(OUT)
–––––
CAM TABLE
–––––
FONT ROM
–––––
CAM DSP CPLD
–––––
CAM SYS
FPGA
–––––
PULSE FPGA
–––––
Adjustable
Range
Display the software version for the
microprocessor-controlled flash.
Display the software version for the
external flash.
Display the table version.
Display the character font version.
Display the program version for the
CPLD (Complex Programmable Logic
Device) that processes camera block
signals.
Display the program version for the
FPGA (Field Programmable Gate
Array) that processes camera block
signals.
Display the program version for the
FPGA that processes the CCD
scanning.
Remarks
Items/
Data Saved
CORRECT ON
–CUFE
DETECTION
(DIG)
–––––
Adjustable
Range
OFF
–
ON/OFF switching for digital black
shading compensation.
Execute digital black shading
compensation.
8-8-4 WHITE SHADING
Items/
Data Saved
CORRECT ON
–CUFE
DETECTION
(V SAW)
–––––
Adjustable
Range
OFF
–
ON/OFF switching for white shading
compensation.
Execute white shading compensation.
Remarks
Remarks
The ____ in the Adjustable Range column indicates the
preset mode.
120
Page 24
Chapter 8 Menu Description Tables (continued)
8-9 OPTION MENU
8-8-6 DIAGNOSTIC2
Items/
Data Saved
SYSCON SOFT
–––––
LCD SOFT
–––––
P2CS OS
–––––
P2CS AP
–––––
MSC FPGA
–––––
SIF FPGA
–––––
DIF FPGA
–––––
Adjustable
Range
Display the software version for the
system control microprocessor.
Display the software version for the
LCD microprocessor.
Display the OS version for the
streaming controller.
Display the application version for the
streaming controller.
Display the program version for MSC
FPGA streaming control and for
recording/playback signal processing
FPGA.
Display the program version for the
serial interface FPGA.
Display program version for the
IEEE1394 interface FPGA.
(when AJ-YAD800G is attached).
Remarks
8-9-1 OPTION
Items/
Data Saved
ENG
SECURITYONOFF
–C–––
ID MIX INH ON
–C–––
AUDIO O UT
DELAY
–C–––
Adjustable
Range
OFF
DELAYED
THROUGH
Remarks
Select whether or not to prohibit
opening the menu screen.
ON: Menu screen cannot be opened.
Please consult your distributor to
release the setting.
OFF: Menu screen can be opened.
Select whether or not to inhibit mixing
the ID in the camera image.
ON: Inhibit mixing. ID is not mixed in
the camera image.
OFF: Do not inhibit. Camera ID setting
under VF INDCATOR1 is
reflected in the camera image.
Select whether or not to delay audio,
headphone and speaker outputs.
DELAYED:
Delay audio output in
synchronisation with video output.
THROUGH:
Output audio input without delay.
This setting prevents echo effect
between the sound source and
audio output when the sound source
is near the camera-recorder.
8
8-8-7 HOURS METER
Items/
Data Saved
OPERATION
–––––
LCD
BACKLIGHT
–––––
P. O N T I M E S
–––––
Adjustable
Range
Display total hours the camera power
has been turned ON.
Display total hours the LCD monitor
backlight power has been turned ON.
Display total number of times the power
switch has been turned ON.
Remarks
<Note>
Menu options for setting 1394 are displayed when an
IEEE1394 interface board (AJ-YAD800G, optional) is
attached. For more information, see the AJ-YAD800G
instruction manual.
The ____ in the Adjustable Range column indicates the
preset mode.
121
Loading...