Panasonic AJ-SDC615P, AJ-SDC905P User Manual

Operating Instructions
Camera/VTR
Before operating this product, please read the instructions carefully and save this manual for future use.
Printed in Japan VQT0N11
F0904W0 -F
@
P
2
indicates safety information.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
FCC Note:
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Warning:
To assure continued FCC emission limit compliance, the user must use only shielded interface cables when connecting to external units. Also any unauthorized changes or modifications to this equipment could void the user’s authority to operate it.
ATTENTION:
The product you have purchased is powered by a nickel cadmium battery which is recyclable. At the end of it’s useful life, under various state and local laws, it is illegal to dispose of this battery into your municipal waste stream. Please call 1-800-8-BATTERY for information on how to recycle this battery.
Ni-Cd
RBRC
RBRC
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER MOUNTING OF THE OPTIONAL INTERFACE BOARD TO QUALIFIED SERVICE PERSONNEL.
Replace battery with part No. CR2032 only. Use of another battery may present a risk of fire or explosion. Caution—Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire.
WARNING:
OTO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
OTO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS—USE AND STORE ONLY IN LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF DRIPPING OR SPLASHING LIQUIDS, AND DO NOT PLACE ANY LIQUID CONTAINERS ON TOP OF THE EQUIPMENT.
The descriptions contained throughout the text of these instructions apply to both the AJ-SDC615 and AJ-SDC905. However, descriptions which apply solely to the AJ-SDC615 are indicated by ; similarly, descriptions which apply solely to the AJ-SDC905 are indicated by .
SDC905
SDC615
3
Contents
Chapter 1 General .................................... 5
1-1 Features of the camera unit ...................... 5
1-2 Features of the VTR unit ........................... 6
1-3 System configuration ................................ 7
Chapter 2 Parts and their functions ....... 8
2-1 Power supply and accessory
mounting section ....................................... 8
2-2 Audio function section .............................. 9
2-3 Shooting and recording/playback
function section ....................................... 11
2-4 Menu operation section ........................... 14
2-5 Time code related section ....................... 15
2-6 Warning/status display section .............. 16
2-7 Display window and its displays ............ 16
2-8 Viewfinder section ................................... 18
Chapter 3 Recording and playback ...... 19
3-1 Cassette tapes .......................................... 19
3-2 Basic procedures ..................................... 20
3-3 Scene-to-scene continuity ...................... 22
3-4 NEWS REC function .................. 22
3-5 PRE-RECORDING function ........ 23
3-6 INTERVAL REC function .......................... 23
3-7 RETAKE function ..................................... 25
3-8 Rec-review function ................................. 25
3-9 Normal playback and playback
at different speeds ................................... 25
Chapter 4 Adjustments and settings for
recording ............................... 26
4-1 Adjusting the white balance and
black balance ........................................... 26
4-1-1 Adjusting the white balance ......................... 26
4-1-2 Adjusting the black balance ......................... 28
4-2 Setting the electronic shutter ................. 29
4-2-1 Shutter modes ............................................. 29
4-2-2 Setting the shutter mode and speed ........... 29
4-2-3 Setting the synchro scan mode ................... 30
4-3 Selecting the recording signals and
recording system ..................................... 30
4-3-1 Selecting the recording signals ................... 30
4-3-2 Selecting the recording system ................... 31
4-4 Selecting the audio input signals and
adjusting their recording levels .............. 31
4-4-1 Selecting the audio input signals ................. 31
4-4-2 Adjusting the audio signal recording levels . 31
SDC905
SDC615
4-5 Setting the time data ................................ 32
4-5-1 Setting the user bits ..................................... 32
4-5-2 Setting the internal clock’s date and time .... 33
4-5-3 Setting the time code ................................... 34
4-5-4 Externally locking the time code .................. 34
4-5-5 Setting the UMID information ...................... 35
4-6
Menu displays on the viewfinder screen
....... 36
4-6-1 Menu configuration ...................................... 36
4-6-2 Basic menu operations ................................ 36
4-6-3 Selecting the user menus ............................ 37
4-7 Viewfinder screen status displays ......... 38
4-7-1 Viewfinder lamp displays.............................. 38
4-7-2 Viewfinder screen status display
configuration..................................................38
4-7-3 Selecting the viewfinder screen display
items ............................................................ 38
4-7-4 Display modes and setting
changes/adjustment result messages ......... 44
4-7-5 Setting the marker displays ......................... 44
4-7-6 Setting the camera ID .................................. 44
4-7-7 Mode check screen displays
(MODE CHECK button function) ................. 45
4-7-8 Marker check screen displays
(MARKER SELECT button function) ........... 45
4-7-9 Checking the return video signal on the
viewfinder .................................................... 45
4-8 Menu-driven function setup .................... 46
4-8-1 Setting the USER SW GAIN switching ........ 46
4-8-2 Selecting the video output signals ............... 46
4-8-3 Selecting the F.AUDIO LEVEL
control function ............................................ 47
4-8-4 Allocating functions to the USER MAIN,
USER1 and USER2 buttons ........................ 47
4-8-5 Setting the color temperature manually ....... 48
4-9 Data handling ........................................... 48
4-9-1 Handling the setup card .............................. 48
4-9-2 Setup card operations ................................. 49
4-9-3 How to use the user data ............................ 52
4-9-4 How to use the scene file data .................... 53
4-9-5 How to return the menus settings to the
user standard settings ................................. 56
4-9-6 How to return the menus settings to the
factory standard settings ............................. 56
4-9-7 How to use the lens file data ....................... 56
Chapter 5 Preparation ........................... 57
5-1 Supplying the power ................................ 57
5-1-1 Attaching the battery and setting the
battery type .................................................. 57
5-1-2 Using an AC power supply .......................... 60
5-2 Attaching the viewfinder and adjusting its
position ..................................................... 60
5-3 Attaching the lens and performing the
flange back and white shading
adjustments .............................................. 61
4
Contents
5-4 Audio input signal preparations ............. 66
5-4-1 When using the front microphone ............... 66
5-4-2 When using an external microphone ........... 66
5-4-3 When using a wireless receiver ................... 67
5-4-4 When using an audio component ................ 67
5-5 Mounting the unit on a tripod ................. 68
5-6 Attaching the shoulder strap .................. 68
5-7 Adjusting the position
of the shoulder pad .................................. 68
5-8 Attaching the rain cover .......................... 69
5-9 Connecting the extension control unit
(AJ-EC3P) ................................................. 69
5-10 Attacching the FEONT AUDIO LEVEL
control knob ............................................. 69
Chapter 6 Maintenance and
inspections ........................... 70
6-1 Inspections prior to shooting ................. 70
6-1-1 Preparation for inspections .......................... 70
6-1-2 Inspecting the camera unit .......................... 70
6-1-3 Inspecting the VTR unit ............................... 71
6-1-4 Self-diagnosis function ................................ 72
6-2 Maintenance ............................................. 73
6-2-1 Condensation ............................................... 73
6-2-2 Head cleaning .............................................. 73
6-2-3 Cleaning inside the viewfinder ..................... 73
6-2-4 Phenomena inherent to CCD cameras ....... 73
6-2-5 Replacing the backup battery ...................... 73
6-2-6 Connectors and signals ............................... 74
6-3 Warning system ....................................... 75
6-3-1 Warning description tables .......................... 75
6-3-2 Error codes .................................................. 77
6-3-3 Emergency eject .......................................... 78
Chapter 7 Menu description tables ...... 79
7-1 Menu configfation .................................... 79
7-2 SYSTEM SETTING .................................... 80
7-2-1 SYSTEM MODE .......................................... 80
7-2-2 OPTION MODE ........................................... 81
7-2-3 REC FUNCTION ......................................... 82
7-2-4 OUTPUT SEL .............................................. 83
7-2-5 GENLOCK ................................................... 83
7-3 PAINT ........................................................ 84
7-3-1 ROP ............................................................. 84
7-3-2 MATRIX ....................................................... 84
7-3-3 COLOR CORRECTION .............................. 85
7-3-4 LOW SETTING ............................................ 85
7-3-5 MID SETTING ............................................. 86
7-3-6 HIGH SETTING ........................................... 86
7-3-7 ADDTIONAL DTL ........................................ 87
7-3-8 SKIN TONE DTL ......................................... 87
7-3-9 KNEE/LEVEL .............................................. 88
7-3-10 GAMMA ....................................................... 88
7-3-11 FLARE ......................................................... 88
7-3-12 CAMERA SETTING .................................... 89
7-4 VF .............................................................. 89
7-4-1 VF DISPLAYS ............................................. 89
7-4-2 VF MARKER ............................................... 90
7-4-3 USER BOX .................................................. 90
7-4-4 VF INDICATOR1 ......................................... 90
7-4-5 VF INDICATOR2 ......................................... 91
7-4-6 MODE CHECK IND ..................................... 91
7-4-7 !LED ............................................................ 91
7-5 OPERATION .............................................. 92
7-5-1 CAMERA ID ................................................ 92
7-5-2 SHUTTER SPEED ...................................... 92
7-5-3 SHUTTER SELECT .................................... 92
7-5-4 USER SW .................................................... 93
7-5-5 SW MODE ................................................... 93
7-5-6 WHITE BALANCE MODE ........................... 94
7-5-7 USER SW GAIN .......................................... 94
7-5-8 IRIS ............................................................. 95
7-6 FILE ........................................................... 95
7-6-1 CARD READ/WRITE ................................... 95
7-6-2 CARD R/W SELECT ................................... 95
7-6-3 LENS FILE .................................................. 96
7-6-4 SCENE ........................................................ 96
7-6-5 INITIALIZE ................................................... 96
7-7 MAINTENANCE ........................................ 96
7-7-1 SYSTEM CHECK ........................................ 96
7-7-2 DIAGNOSTIC .............................................. 96
7-7-3 LENS ADJ ................................................... 96
7-7-4 BLACK SHADING ....................................... 97
7-7-5 WHITE SHADING ....................................... 97
7-8 VTR MENU ................................................ 97
7-8-1 VTR FUNCTION .......................................... 97
7-8-2 BATTERY/TYPE ......................................... 98
7-8-3 BATTERY SETTING1 ................................. 98
7-8-4 BATTERY SETTING2 ............................... 100
7-8-5 MIC/AUDIO1 ............................................. 101
7-8-6 MIC/AUDIO2 ............................................. 102
7-8-7 TC/UB ........................................................ 102
7-8-8 UMID SET/INFO ........................................ 103
7-8-9 VTR DIAG ................................................. 103
7-9 OPTION MENU......................................... 104
7-9-1 OPTION ..................................................... 104
Chapter 8 Specifications ..................... 105
UniSlot ®is a registered trademark of Ikegami Tsusinki co., Ltd.
Chapter 1 General
1
5
3 CCDs with a 2/3-inch on-chip lens
Aspect ratios of 16:9 and 4:3 are supported.
Storage type high-sensitivity function
The unit comes with a storage type gain increase function. This is a function that makes it possible to achieve a higher sensitivity of up to 20 dB above the regular gain increase.
<Note>
Due to the properties inherent to the unit’s CCD image sensors, the top left part of the screen may become slightly brighter when the cumulative gain is increased.
Digital zoom function
The unit is equipped with a digital zoom employing function. This function is particularly useful when zooming further in on a subject.
12-bit A/D conversion digital signal processing
circuitry
The analog images are processed into digital data by a 12­bit A/D converter with sampling frequencies of 18 MHz, and by operating the signal processor using the 36 MHz frequency, it is possible to reproduce images which are more finely detailed and achieve improvements in stability and reliability.
12-axis independent color correction function
Serving as a paint function, this facility enables the colors for 12 axes to be compensated for independently and is very useful for creating finely detailed images.
Data control function
When the unit is used on its own, one set of user data and four sets of scene file data can be registered. Further, by using an SD card or a Multimedia Card (optional accessory) as the setup card, up to eight sets of setup data can be stored.
<Note>
SD card and MultiMedia card used in this unit do not comply with the SD standard. Do not use cards formatted using this unit with other camera-recorders. Further, NTFS and FAT32 formatted cards cannot be used with this unit. The recommended size for SD cards is 8 MB or more and 4 MB or more for MultiMedia cards.
MARKER SELECT button
At the front of the unit is a button for checking the information concerning the markers on the viewfinder screen. This is useful for checking the picture angle, for instance, during shooting.
ECU supported
The unit supports the AJ-EC3P extension control unit.
Single-action shoulder pad slide function
It is now possible to adjust the position where the unit is optimally balanced for operation using a single-touch action. This means that the operator can easily optimize the unit’s balance when the lens, battery and other peripheral camera devices have been installed on the unit.
1-1 Features of the camera unit
The models AJ-SDC615 and AJ-SDC905 are camera recorders featuring three CCD image sensors which each have a 2/3-inch on-chip lens. The AJ-SDC905 supports both the DVCPRO and DVCPRO50 formats. (The AJ-SDC615 supports only the DVCPRO format.) Both camera recorders feature a compact size, light weight, low power consumption, high image quality, high sensitivity, excellent mobility and outstanding dust-proof and moisture-proof characteristics. They are ideally suited not only for news gathering but also for a wide range of production applications. Both their camera and VTR units employ digital signal processing technology to achieve an improved image quality and stability, and they configure a system which enables data management using setup cards. An IEEE 1394 connector is provided as a standard feature for increased mobility.
SDC615SDC905
Chapter 1 General
6
DVCPRO and DVCPRO50 formats supported
The VTR unit compresses the images using a component digital recording system that uses the latest compression technology, and for the sound it employs non-compression PCM recording with an excellent signal-to-noise ratio, frequency band, waveform characteristics and reproduction characteristics of the finely detailed areas. As a result, both the picture quality and sound quality are taken to new heights of excellence. A choice of recording formats tailored to the application at hand is offered: the DVCPRO50 format when priority is required to be given to the picture quality, and the DVCPRO format when economy is to be given precedence.
DVCPRO format supported
The VTR unit compresses the images using a component digital recording system that employs the latest compression technology, and for the sound it uses non­compression PCM recording with an excellent signal-to­noise ratio, frequency band, waveform characteristics and reproduction characteristics of the finely detailed areas. As a result, both the picture quality and sound quality are taken to new heights of excellence.
Power-saving management function
In order to reduce its power consumption efficiently, the unit has a function that shuts down circuitry that is not required for the particular VTR mode established at the time. This enables the user to perform operations while conserving power.
Pre-recording function featured
This function makes it possible to record the pictures and sound up to 6 seconds ahead of the point in time when recording is commenced by pressing the VTR START button or VTR button on the lens. It is effective in preventing shots from being missed.
Interval REC function provided
This unit is capable of interval shooting. The AJ-SDC905 makes it possible to conduct recording in intervals with a minimum recording time in increments of one frame. The AJ-SDC615 makes it possible to conduct recording in intervals with a recording time of 2 seconds or more. This is particularly useful for shooting science and nature programs. Furthermore, when the unit is used for one-shot recording, frame-by-frame shooting is easily accomplished.
SDC615
SDC905
SDC905
SDC615
SDC905
NEWS REC function
This function especially supports shooting in the context of news gathering or documentary filming to ensure that shutter opportunities are not passed up. By controlling the start key acknowledgment time, the unit can continuously record without the user having to interrupt the recording: this safeguards against the failure to record those precious moments—a failure that occurs when recording is resumed after it has been shut down temporarily.
RETAKE function
This function is for not leaving behind superfluous cuts when a cut turns out to be no good during the shooting of news, reports or art programmes. By cutting down on the time taken for copying onto the work tape, for instance, this function is very effective in achieving economical operation. Users should remember to handle this function very carefully.
Input signals of 2 separate audio channels
supported
The unit enables the audio input signals in two channels to be selected separately. Further, the level of the signal in each channel can be monitored on the LCD display window.
Front audio level control
The unit’s front panel is equipped with a control for adjusting the audio recording level. This is useful when the user is filming on his or her own and the audio level needs to be adjusted. It also is possible to cancel the effect of this control.
UniSlot®wireless receiver
The unit’s construction supports a slot-in wireless receiver which is available as an optional accessory.
Built-in DOLBY NR system
The CUE audio recording circuitry contains a Dolby B noise reduction circuit.
Frame-to-frame continuity
Simply by pressing the VTR START button or VTR button on the lens, the continuity from one frame to the next is assured with a precision of +1 frame or less.
Rec-review function
This automatically rewinds the tape for the last 2 to 10 seconds recorded and plays back the recording. This enables the recording to be monitored without delay.
Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol Îare trademarks of Dolby Laboratories Licensing Corporation.
SDC615
1-2 Features of the VTR unit
26-pin camera adapter: AJ-CA905G
26-pin cable: AJ-C26050G (50 m), AJ-C26100G (100 m)
Remote control unit: AJ-RC905
V-mount type battery plate
NP-1 type battery holder
BP-90 type battery holder
PRO14, TRIM14, HYTRON50/100/120, DIONIC90/160
ENDURA50/80, BP-L60/90
NP-L50
BP-H120, HP-90L
Battery
Chapter 1 General
1
7
Microphone kit: AJ-MC700
UniSlot®wireless microphone receiver: Sennheiser EK3041
Microphone holder: AJ-MH700
Lens (Bayonet type): Fujinon, Canon
Rain cover: SHAN-RC700
Soft carry case: AJ-SC900
(Can not purchase in some area.)
Hard carry case: AJ-HT901
AC adapter: AJ-B75
Devices compliant with IEEE 1394 standard
Cassette tapes: AJ-5P23MP AJ-5P33MP AJ-P12MP AJ-P24MP AJ-P33MP AJ-P66MP
Cleaning tape: AJ-CL12MP
Extension control unit: AJ-EC3P
Viewfinders: AJ-VF15B AJ-VF20WB
GPS unit: AJ-GPS900G
Tripod attachment: SHAN-TM700
Video camera-recorder: AJ-SDC615 AJ-SDC905
1-3 System configuration
SD memory cards Multimedia cards
Built-in time code generator/reader
This enables the time code information to be recorded on the dedicated sub-code track and played back.
Metadata supported
The unit allows information from the AJ-GPS900G GPS unit to be recorded on tape as the metadata UMID information. This is useful when it comes to managing on-tape information.
DVCPRO (IEEE 1394 digital input/output)
connector provided
The unit is standard equipped with an input/output connector for signals complying with the IEEE 1394 standard. This connector can be connected with an external unit using an IEEE 1394 cable.
Chapter 2 Parts and their functions
8
1 POWER switch
This switch turns the power ON and OFF.
2 Battery mount
This is for attaching the Anton Bauer battery pack.
3 DC IN (external power input) socket (XLR, 4-pin)
When operating this unit using an AC power source, this socket is connected to the model AJ-B75 AC adapter (optional accessory).
4 BREAKER switch
If an excessively high current flows inside the unit due to some problem or other, the circuit breaker is tripped and the power is automatically turned off to protect the unit. Push this button in after an inspection has been conducted or repairs performed inside the unit by a qualified service person. If there are no problems, the power will come back on.
5 GPS connector
The connector from AJ-GPS900G, a GPS unit available as an optional accessory, is connected here.
6 Shoulder belt fittings
The shoulder belt is attached here.
7 Light shoe
Use this to attach the video light, etc.
8 Lens mount (bayonet type)
The lens is attached to this mount.
9 Lens lever
This lever is tightened to secure the lens after it has been attached to the lens mount.
: Lens mount cap
To remove the cap, push the lens lever 9 up. Keep the cap in place while the lens is not attached.
; Lens cable/microphone cable clamp
This clamp is for anchoring the lens cable or microphone cable.
< Tripod mount
Mount the tripod attachment (SHAN-TM700), available as an optional accessory, when the unit is to be anchored to a tripod.
= LENS jack (12-pin)
The connecting cord of the lens is connected to this jack. For further details on the lenses that can be used, refer to the operating instructions of the lenses concerned.
> Easy-to-adjust shoulder pad
The position of the shoulder pad can be adjusted backward or forward so that the unit is balanced when it is carried on the user’s shoulder.
1
34
6
2
5 7
8
9
:
; <=>
6
2-1 Power supply and accessory mounting section
Chapter 2 Parts and their functions
2
9
2-2 Audio function section (input system)
1
2
569@? ?8
= < > 73; :
4
1 MIC IN (microphone input) jack (XLR, 3-pin)
Connect the microphone (optional accessory) here. The power for the microphone is supplied from this jack.
2 AUDIO LEVEL CH1/CH2 (audio channel 1 & 2 recording
level adjustment) controls
When the AUDIO SELECT CH1/CH2 switch 3 is set to MAN, the recording level of audio channels 1 and 2 can be adjusted using these controls. The controls come with a locking mechanism. Therefore, to adjust the recording level, simultaneously push in and turn the controls.
3 AUDIO SELECT CH1/CH2 (audio channel 1 & 2
automatic/manual level adjustment selector) switch
This is used to select the method for adjusting the recording levels of audio channels 1 and 2.
AUTO : Set here for automatic adjustment. MAN : Set here for manual adjustment.
4 AUDIO IN (audio input selector) switch
These are used to select the input signals to be recorded on audio channels 1 and 2.
FRONT :
The input signals supplied from the microphone which has been connected to the MIC IN jack 1 are recorded.
W.L. (wireless) :
The input signals from the slot-in wireless microphone receiver are recorded.
REAR :
The audio input signals supplied from the audio component which has been connected to the AUDIO IN CH1/CH2 connectors 5 are recorded.
5 AUDIO IN CH1/CH2 (audio input channel 1 & 2)
connectors (XLR, 3-pin)
An audio component or microphones are connected here.
6 LINE/MIC/+48V (line input/mic input/mic input + 48V)
selector switch
This is used to switch the audio input signals from the audio component which has been connected to the AUDIO IN CH1/CH2 connectors 5. LINE : The audio input signals from the audio component
serving as the line input are selected.
MIC : The audio input signals from the internal power
supply type of microphone are selected. (The phantom mic power is not supplied from the unit.)
+48V : The audio input signals from the external power
supply type of microphone are selected. (The phantom mic power is supplied from the unit.)
7 Wireless receiver slot
The UniSlot
®
wireless receiver (optional accessory) can be
attached here.
8 FRONT AUDIO LEVEL (audio recording level
adjustment) control
This enables the recording level of audio channels 1 and 2 to be adjusted. This level can be adjusted regardless of the setting position of the AUDIO SELECT switch. When the <MIC/AUDIO1> screen is opened from the VTR MENU page by performing a menu operation, whether to enable or disable the operation of this level control can be set using the FRONT VR CH1 and FRONT VR CH2 setting items.
O The same signals as for CH1 are recorded on audio track CH3.
Similarly, the same signals as for CH2 are recorded on audio track CH4.
O The signals are recorded on two channels (CH1 and CH2) when the
DVCPRO format (25 Mbps) is set.
SDC905
The mixed signals of audio channels 1 and 2 are output to the remote control unit (AJ-RC905). The signals are output now as is without the adjustment of their level, etc.
Chapter 2 Parts and their functions
10
2-2 Audio function section (output system)
2 Either STEREO or MIX can be selected as the setting for the MONITOR
SELECT item by opening the <MIC/AUDIO2> screen from the VTR MENU page by performing a menu operation.
CH1/3 Audio channel 1 Audio channel 3
MONITOR SELECT CH1/2OCH3/4 selector switch
CH1/2 CH3/4
ST
Stereo2signals of audio channels 1 and 2
Stereo2signals of audio channels 3 and 4
CH2/4 Audio channel 2 Audio channel 4
9 AUDIO OUT connector (XLR, 5-pin)
The audio signals recorded on audio channels 1 and 2 or audio channels 3 and 4 are output from this connector. With the AJ-SDC905 , the signals to be output can be selected using the MONITOR SELECT CH1/2OCH3/4 selector switch.
: MONITOR SELECT (audio channel)
CH1/2OCH3/4 selector switch
This is used to select the audio channels whose signals are to be output to the speaker, earphone and AUDIO OUT connector.
CH1/2 : The signals of audio channels 1 and 2 are output. CH3/4 : The signals of audio channels 3 and 4 are output.
In addition, the channel indications for the audio level meters appearing in the display window and viewfinder change when this switch is operated.
MONITOR SELECT (stereo/mix)
STOMIX selector switch
This is used to select the sound which is to be output to the speaker, earphone and AUDIO OUT connector. ST: The stereo audio signals of channels 1 and 2 are
output.
MIX: The mixed audio signals of channels 1 and 2 are
output.
; MONITOR SELECT (audio selection)
CH1/3OSTOCH2/4 selector switch
This is linked with the MONITOR SELECT CH1/2OCH3/4 selector switch and used to select the sound which is to be output from the speaker, earphone and AUDIO OUT connector.
CH1/3 : The signals of audio channel 1 or 3 are output. ST : The stereo audio signals of either audio channels
1 and 2 or audio channels 3 and 4 are output. Using a menu setting, the stereo signals can be changed to MIX signals.
CH2/4 : The signals of audio channel 2 or 4 are output.
SDC905
SDC615
SDC905
SDC905
CH1 Audio channel 1 Audio channel 1
MONITOR SELECT STOMIX selector switch
ST MIX
1/2
Stereo signals of audio channels 1 and 2
Mixed signals of audio channels 1 and 2
CH2 Audio channel 2 Audio channel 2
< MONITOR (volume) control
This is used to adjust the volume of the monitor speaker or earphone.
= ALARM (warning alarm volume adjustment)
This is used to adjust the volume of the warning alarms from the earphones which have been connected to the speaker > or PHONES jack ?. The warning alarms are not audible when this control is at its lowest setting.
> Speaker
The EE sound during recording or the playback sound during playback can be monitored through this speaker. The warning alarms are output in synchronization with the flashing or lighting of the warning lamps and warning displays. The sound heard from the speaker is automatically cut off when earphones are connected to the PHONES jack ?.
? PHONES (earphones) jack (mini jack)
This is the earphone (stereo) jack which is used to monitor the audio signals. When earphones are connected, the sound from the speaker is automatically cut off. The sound which is output from the two jacks (front and rear) is the same.
@ DC OUT (DC power supply) output socket
This normally serves as the DC 12 V output socket. A current of approximately 1 A can be supplied.
MONITOR SELECT (audio selection)
CH1O1/2OCH2 selector switch
This is linked with the MONITOR SELECT STOMIX selector switch and used to select the sound which is to be output from the speaker, earphone and AUDIO OUT connector.
CH1: The signals of audio channel 1 are output. 1/2: The stereo audio signals of audio channels 1 and 2
are output. The stereo signals can be changed into mixed signals using the MONITOR SELECT STOMIX selector switch.
CH2: The signals of audio channel 2 are output.
SDC615
Chapter 2 Parts and their functions
2
11
1 9 84
@
765< >2 = BAC I
?
;
:
3
ª
6
5
1/;
EJECT
/
REW FF
/
STOP PLAY/PAUSE
D G H
E F
2-3 Shooting and recording/
playback
function section
Shooting and recording (camera unit)
1 FILTER (filter switching) controls
These are used to select the filter in accordance with the subjects brightness and color temperature.
1: 3200 K (transparent) 2: 5600 K+1/8 ND 3: 5600 K 4: 5600 K+1/64 ND
2 AUTO W/B (white/black) BAL switch
AWB : The white balance is automatically adjusted. When
the AWB memory selector switch on the side panel is set to A or B and then the AUTO W/B BAL switch is operated, the adjustment value is recorded in the memory. When VAR has been selected as the setting for AWB A and/or AWB B menus, the value will be the one set in the menu and this switch will not function. Note that this switch will also not function at the PRST position.
ABB : The black balance is automatically adjusted.
If the AUTO W/B BAL switch is held down at the ABB position for 5 or more seconds, the black shading is compensated automatically.
<Note>
When white balance or black balance are being automatically adjusted and the switch is pressed again to either the AWB side or to the ABB side, the automatic adjustment for the side pressed will be stopped. The adjusted value in this case is the value before automatic adjustment was performed.
3 SHUTTER switch
This is the ON/OFF selector switch of the electronic shutter.
OFF : The electronic shutter does not operate. ON : The electronic shutter operates. SEL : This is used when the electronic shutter speed is to
be changed. The switch is a non-locking type. The shutter speed changes each time it is operated. For further details, refer to 4-2 Setting the electronic shutter.
4 Synchro scan adjustment switches
These switches become effective when the shutter switch 3 is set to ON and SYNCHRO SCAN is selected. They are used to adjust the synchro scan speed. When the “–” switch is pressed, the shutter speed is reduced; conversely, when the “+” switch is pressed, it is increased. During personal computer monitor shooting, etc. adjust these switches to the positions where the horizontal bar noise inside the viewfinder is decreased.
5 GAIN selector switch
This is used to select the gain of the video amplifier in accordance with the lighting conditions prevailing at the time of the shooting. The gain values for the L, M and H settings are set ahead of time on the setting menu. Their factory settings are 0 dB, 9 dB and 18 dB, respectively.
$ Examples of filter selection
Shooting conditions Filter
Sunrise, sunset, inside a studio 1 (3200 K)
Outdoors under cloudy or rainy skies 3 (5600 K)
Outdoors under a clear sky 2 (5600 K+1/8 ND)
or 4 (5600 K+1/64 ND)
Snowscapes, high mountains, seashores or other perfectly clear scenery
4 (5600 K+1/64 ND)
Chapter 2 Parts and their functions
12
AUTO KNEE function
When shooting with the level set to people or scenes against a high­brightness background, the background will be whitened out, and the buildings and scene in the background will be blurred. If the AUTO KNEE function is activated at times like this, the background will be reproduced clearly. This function is effective for shooting in the following situations:
When shooting people in the shade under a clear skyWhen simultaneously shooting people in a car or indoors and the
outside scenery through a window
When shooting scenes with a strong contrast
6 OUTPUT/AUTO KNEE selector switch
This switch selects the video signals which are to be output from the camera unit to the VTR unit, viewfinder and/or video monitor.
CAM. AUTO KNEE ON:
The images shot by the camera are output. The AUTO KNEE circuit operates.
CAM. AUTO KNEE OFF:
The images shot by the camera are output. The MANUAL KNEE circuit operates.
BARS:
Color bar signals are output. The AUTO KNEE circuit does not operate.
7 WHITE BAL (white balance memory selector) switch
This is used to select the method used to adjust the white balance.
PRST:
Set the switch to this position at times when, for instance, there is no time to adjust the white balance. The factory setting for the white balance is 3200K, but this can be changed to any other value by a menu setting. For details, refer to 4-8-5 Setting the color temperature manually.
A or B:
When the AUTO W/B BAL switch 2 is set to AWB, the white balance is automatically adjusted, and the adjusted value is stored in memory A or memory B. For details, refer to 4-1-1 Ajusting the white balance. As the factory setting, the settings are to be allocated to the memory. Using a menu setting, it is also possible to allocate the setting for the auto tracking white balance (ATW) performed with the automatic tracking system to memory B or allocate the color temperatures of the user's choice to memory A and memory B. For details, refer to 4-8-5 Setting the color temperature manually.
8 MODE CHECK button
Each time this button is pressed, one of the four screen pages (STATUS screen display, !LED screen display, FUNCTION screen display and AUDIO screen display) is selected and displayed on the viewfinder to indicate the cameras settings. This does not affect the output signals of the camera.
9 MARKER SELECT button
This is used to select the marker information displays on the viewfinder screen. Each time it is pressed, the two marker information display screens set by the menu are switched in the following sequence: A (A marker display) 5 B (B marker display) 5 OFF (no marker display) 5 A, and so on repeatedly. Note that when the power is switched ON, the display on the viewfinder screen immediately before the power was switched OFF will appear. For details, refer to 4-7-8 Marker check screen displays.
: USER MAIN, USER 1 and USER 2 buttons
A user setting can be allocated to each of these buttons using the setting menu. When a button is pressed, the user setting mode allocated to it is selected. When the button is pressed again, the selected mode is released. For details, refer to 4-8-4 Allocating functions to the USER MAIN, USER1 and USER2 buttons.
Shooting and recording (VTR unit)
; VTR START/STOP button
When this is pressed, recording starts; when it is pressed again, recording stops. This button functions in the same way as the lens VTR button.
< VTR SAVE/STBY (tape protection) switch
This is used to select the power supply mode when the VTR has temporarily stopped recording (REC PAUSE mode). SAVE: This is the tape protection mode. The cylinder is
stopped in the half-loading status. Less power is consumed than at the STBY position, and the operating time provided by the battery is prolonged. Compared with the STBY position, it takes longer for recording to commence after the VTR START button ; has been pressed. When the switch is set to this position, the VTR SAVE lamp inside the viewfinder lights.
STBY : At this position, recording is commenced as soon
as the VTR START button is pressed.
<Note>
When the prescribed amount of time has elapsed in the STBY mode, the unit is automatically set to the SAVE mode. To return the unit to the STBY mode, set the VTR SAVE/STBY switch to SAVE, and then again to the STBY position.
Chapter 2 Parts and their functions
2
13
= OUTPUT SEL (output signal selection) switch
This is used to select the signals output from the VIDEO OUT connector and MON OUT connector. VTR : In the recording or other EE mode, the camera
images are output from the connectors; in the playback or other VV mode, it is the VTRs playback signals which are output.
CAM : The camera images are output at all times. OFF : The video output is stopped and the power
reduction mode is established. Furthermore, the audio output signals are synchronized with the video signals as well. For details on the video output, refer to 4-8-2 Selecting the video output signals.
<Notes>
O During recording, the output signals are not switched
even when the position of this switch is changed. They are switched when the recording operation is stopped.
O When the signals input to the GENLOCK IN connector
or DVCPRO connector are selected as the signals to be recorded, the switch setting will be the same as at the VTR position even if the switch is set at the CAM position.
> VIDEO OUT CHARACTER switch
This is used to control the superimposing of the characters onto the images which are output from the VIDEO OUT connector.
ON : The characters are superimposed onto the images. OFF : The characters are not superimposed onto the
images. For details on the character types, refer to 4-8-2 Selecting the video output signals.
? VIDEO OUT (video signal output) connector
This is the video signal output connector. The video signals linked to the setting of the OUTPUT SEL switch are output from here.
@ ECU REMOTE (remote control) connector
The AJ-EC3P extension control unit (optional accessory) is connected here.
A MON OUT (monitor output) connector
This is the connector for outputting the video signal which is used for monitoring. The video signals linked to the setting of the OUTPUT SEL switch are output from here. Whether characters are to be superimposed onto the images output from the VIDEO OUT connector can be selected separately using the internal menu. For details, refer to 4-8-2 Selecting the video output signals.
B GENLOCK IN connector
The reference signal is input to this connector when genlock is to be established with the camera unit or when the time code is to be externally locked. This signal can also be used as the return signal. The connector serves as a video input connector for receiving the video signals from an external unit when the <SYSTEM MODE> screen is opened from the SYSTEM SETTING page by performing menu operations and VIDEO is selected as the REC SIGNAL menu item setting.
<Note>
A standard VBS signal (a composite signal including a burst signal) should be supplied as the input reference signal.
C DVCPRO connector (6-pin)
This is the input/output connector for signals which comply with the IEEE 1394 standard. It can be connected with an external unit using an IEEE 1394 cable.
<Notes>
O Power is not supplied from the unit. O Before proceeding to connect or disconnect the DV
cable (IEEE1394), be absolutely sure to turn off the power of the units that are to be connected or disconnected using this cable.
O Before proceeding to connect
the unit which uses a 6-pin type of DV connector, carefully check the shape of the connectors on the DV cable and unit. Connecting a connector upside down may damage the parts inside the camera-recorder and cause malfunctioning. Always connect the DV cable to the unit with the 6-pin type DV connector first.
O When recording signals from an external unit, first check
that video signals are supplied.
O While signals from an external unit are being recorded,
do not operate the external unit or disconnect any of its cables. This will stop the output, which may result in the signals not being recognized when recording is resumed.
O You can connect a digital video unit equipped with a DV
connector and digitally transfer video and audio signals as well as time codes and other information.
O When a DV cable has been connected to the DV
connector, do not apply any strong external force as this may damage the connector.
D EJECT button
This is pressed to insert or eject the cassette.
E STOP button
This is pressed to stop the tape travel.
6-pin type
4-pin type
Chapter 2 Parts and their functions
14
4 3
2
1
2-4 Menu operation section
1 MENU button
This is used to switch the menu ON and OFF.
2 JOG dial button
This is used to select the menu items and perform settings when the MENU button 1 is at the ON position.
3 Setup card insertion slot
This is where the SD card (optional accessory) or Multimedia card (optional accessory) is inserted into the unit.
4 BUSY (operation mode display) lamp
This lamp shows the operation mode of the setup card. It lights during operation.
<Note>
When this lamp is lighted, refrain from inserting or removing the card.
F PLAY/PAUSE button
This is pressed to view the playback picture on the viewfinder screen or using a color video monitor. The buttons lamp comes on during playback. When it is pressed during playback, the unit is set to pause in the playback mode (PLAY PAUSE), and the button’s lamp flashes. If the unit is left in the pause mode for two minutes, it automatically changes to the stop (STOP) mode.
G REW (rewind) button and lamp
When this button is pressed during stop, the tape is reviewed at high speed. Its lamp lights at this time. When it is pressed during playback or pause, the tape is reviewed at approximately 4 times the normal tape speed. Both the PLAY lamp and REW lamp light at this time.
H FF (fast forward) button and lamp
When this button is pressed during stop, the tape is cued at high speed. Its lamp lights at this time. When it is pressed during playback or pause, the tape is cued at approximately 4 times the normal tape speed. Both the PLAY lamp and FF lamp light at this time.
I EMERGENCY screw (inside rubber cap)
If the cassette does not eject even when the EJECT button is pressed, use a screwdriver or similar implement to push and turn the EMERGENCY screw at the same time: this will cause the cassette to be ejected. For details, refer to 6-3-3 Emergency eject.
Chapter 2 Parts and their functions
2
15
3 21
9
64 5
78
2-5 Time code related section
1 GENLOCK IN connector (BNC)
The reference signal is input to this connector when genlock is to be established with the camera unit or when the time code is to be externally locked.
2 TC IN connector (BNC)
Supply the time code which will serve as the reference to this connector when externally locking the time code.
3 TC OUT connector (BNC)
To lock the time code of an external VTR to the units time code, connect this connector to the time code input (TC IN) connector on the external VTR.
4 HOLD button
The time data display of the counter display section which was on the screen at the moment when this button is pressed is held. (However, the time code generator keeps running.) When the button is pressed again, the hold status is released. It is used, for instance, to find out the time code or CTL counter value at which a particular scene was shot.
5 RESET button
This is used to reset the time data on the counter display section to 00:00:00:00. If it is pressed while the TCG switch 9 is at the SET position, the time code data and user bits data are respectively reset to 00:00:00:00.
6 DISPLAY switch
This is used to display the time code, CTL or user bits on the counter display section depending on the setting positions of this switch and the TCG switch 9.
UB : The user bits are displayed. TC : The time code is displayed. CTL : CTL is displayed.
7 “+ button, “–” button
These are used to increment or decrement by 1 the figure in the digit which was made to flash by the SHIFT button 8 when the time code or user bits are to be set.
8 SHIFT button
This causes the digit to be set to flash when the time code or user bits are to be set.
9 TCG (time code selector) switch
This is used to set the running mode of the built-in time code generator. F-RUN : Set here to have the time code run all the time
regardless of the VTRs operation. This position is used to align the time code with the time or externally lock the time code.
SET : Set here when the time code or user bits are to be
set.
R-RUN : Set here to have the time code run only during
recording. The time code on the tape with scene­to-scene continuity is recorded continuously.
Chapter 2 Parts and their functions
16
5
1
2
4
3
6
2-6 Warning/status display section 2-7 Display window and its displays
Remaining tape and remaining battery charge and audio channel level displays
Displays relating to the VTR units operations and modes
CTL
RF
SERVO
HUMID
SLACK
h
TAPE
EB
Y minM
s
frm
13 24
0
D
VTCG
TIME DATE
P-iREC
SLAVE HOLD W GPS
BATT
EF
OVER OVER
10
OO
40
-dB
30
20
NDF
Remaining tape display
The remaining tape time is displayed using 7 segments. The remaining tape time indicated by each segment is set to 3 minutes or 5 minutes using TAPE REMAIN/on the VTR MENU BATTERY/TAPE screen. Each time the number of minutes set for the segments elapses, one segment is cleared.
Remaining battery charge display
If a battery with a digital display (% display) is used, all 7 segments up to the “F” position light when the 70% or more of the battery charge remains. When there is less than 70% of the battery charge remaining, the segments go out one by one in sequence every time the remaining charge drops by 10%. It is also possible to set all 7 segments to light at a 100% battery charge by selecting 100% as the setting for BATT REMAIN FULL on the <BATTERY/TAPE> screen of the VTR menu.
Audio channel level meter
When the MONITOR SELECT CH1/2OCH3/4 switch is set to CH1/2, numbers 1 and 2 indicating the audio channels appear, and the CH1 and CH2 audio levels are displayed. Conversely, when it is set to CH3/4, numbers 3 and 4 indicating the audio channels appear, and the CH3 and CH4 audio levels are displayed.
SDC905
CTL
RF
SERVO
HUMID
SLACK
h
TAPE
EB
Y minM
s
frm
13 24
0
D
VTCG
TIME DATE
P-iREC
SLAVE HOLD W GPS
BATT
EF
OVER OVER
10
OO
40
-dB
30
20
NDF
Error code display
(for details, refer to 6-3 Warning system”)
Warning displays
RF: Clogged video head SERVO: Servo disturbance HUMID: Formation of condensation on the head drum SLACK: Problem in tape take-up
For details, refer to 6-3 Warning system.
1 Back tally lamp
When the back tally switch 2 is set to ON, this lamp serves the same function as the front tally lamp in the viewfinder.
2 Back tally switch
This is used to control the units back tally lamp 1 and rear tally lamp 6.
ON : The back tally lamp and rear tally lamp operate. OFF : The back tally lamp and rear tally lamp do not
operate.
3 WARNING lamp
When a problem of some form or other occurs within the VTR unit, this lamp flashes or lights.
4 LIGHT switch
This controls the lighting of the display window. Each time it is pressed, the lighting of the display window
5 is set in turn from on to off or vice versa.
5 Display window
This displays the alarms, remaining battery charge, audio levels, time data, etc. relating to the VTR unit.
6 Rear TALLY lamp
When the back tally switch 2 is set to ON, this lamp operates in exactly the same way as the back tally lamp.
Chapter 2 Parts and their functions
2
17
CTL
RF
SERVO
HUMID
SLACK
h
TAPE
EB
Y minM
s
frm
13 24
0
D
VTCG
TIME DATE
P-iREC
SLAVE HOLD W GPS
BATT
EF
OVER OVER
10
OO
40
-dB
30
20
NDF
Mode displays
W: Lights when the 16:9 aspect ratio mode is established. GPS: Lights when signals cannot be received during GPS operation. GPS : Lights when signals are being received during GPS operation. P-REC: Lights in pre-recording mode and flashes during the time set for
pre-recording after the tally lamp for recording has turned off.
iREC:Lights during recording when the interval recording mode is
established; flashes during recording standby.
i: Flashes when the interval recording mode has been selected.
Displays relating to the time code
NDF: Lights when the time code is in the non-drop frame mode. DF: Lights when the time code is in the drop frame mode. SLAVE: Lights when the time code is locked externally. HOLD: Lights when the time generator/reader value is being held. CTL: Lights when CTL is selected by the DISPLAY switch and the
CTL count value is displayed.
TCG: Lights when TC (or UB) is selected by the DISPLAY switch and
the TC (or UB) generator value is displayed.
TC: Lights when TC (or UB) is selected by the DISPLAY switch and
the TC (or UB) reader value is displayed.
VTCG: Lights when UB is selected by the DISPLAY switch and the
VIUB generator value is displayed.
VTC: Lights when UB is selected by the DISPLAY switch and the
VIUB reader value is displayed.
TIME: Lights when UB is selected by the DISPLAY switch and the
values of the hour, minutes and seconds in real time are displayed.
DATE: Lights when UB is selected by the DISPLAY switch and the
values of the year, month and day are displayed in real time.
No display: Remains off when UB is selected by the DISPLAY switch and
the real-time values of the hour and minutes in the time zone are displayed.
Time counter display:
The time code, CTL, user bits and real time are displayed.
<Note>
When UB has been selected by the DISPLAY switch, each time the HOLD button is pressed, the setting is switched in the following sequence: VTCG (VTC) 5 DATE 5 TIME 5 no display (time zone) 5 TCG (TC) and so on repeatedly.
Time code-related switch settings and display items
TCG switch position
DISPLAY switch
position
Display item
SET
TC or CTL Time code
F-RUN or R-RUN
UB User bits
CTL CTL
TC Time code
UB User bits
Chapter 2 Parts and their functions
18
2-8 Viewfinder section
ON
OFF
2
8
7;=
<
1
:
9
3645
>
?
@
1 Viewfinder (optional accessory)
While recording or playback is underway, pictures can be viewed through the viewfinder in black and white. The warning displays concerning the units operation statuses and settings, messages, zebra patterns and markers (safety zone markers and center marker) can also be seen in the viewfinder.
2 ZEBRA (zebra pattern) switch
This is used to display the zebra pattern in the viewfinder.
ON : The zebra pattern is displayed. OFF : The zebra pattern is not displayed.
3 TALLY switch
This is used to control the front tally lamp 7.
HIGH: The brightness of the front tally lamp is increased. OFF : The front tally lamp is turned off. LOW : The brightness of the front tally lamp is reduced.
4 PEAKING control
This is used to adjust the outlines of the images seen inside the viewfinder to make focusing easier. Its adjustment does not affect the output signals of the camera.
5 CONTRAST control
This is used to adjust the contrast of the picture seen inside the viewfinder. Its adjustment does not affect the output signals of the camera.
6 BRIGHT control
This is used to adjust the brightness of the picture seen inside the viewfinder. Its adjustment does not affect the output signals of the camera.
7 Front tally lamp
This lamp is activated when the TALLY switch 3 is set to the HIGH or LOW position, and it lights while the VTR unit is recording. It also flashes to provide a warning display like the REC lamp inside the viewfinder. The lamp’s brightness (HIGH or LOW) when it is lighted can be selected using the TALLY switch.
8 Back tally lamp
This lamp lights while the VTR unit is recording. It also flashes to provide a warning display like the REC lamp inside the viewfinder. When the lever is set to OFF, the back tally lamp is hidden.
9 Eyepiece
: Diopter adjustment ring
This is adjusted in line with the camera operators diopter in such a way that the user can see the image on the viewfinder screen most clearly.
; Connecting plug
< Locking ring
= Microphone holder
> Viewfinder stopper
This is used to attach and remove the viewfinder.
? Viewfinder left-right position anchoring ring
This is used to adjust the left-right position of the viewfinder.
@ Viewfinder front-back position anchoring ring
This is used to adjust the front-back position of the viewfinder.
<Note>
For details, refer to 5-2 Attaching the viewfinder and adjusting its position.
Chapter 3 Recording and playback
3
19
3-1 Cassette tapes
Loading a cassette tape
1
Set the POWER switch to ON.
<Note>
When condensation has formed inside the unit, the HUMID display lights. Wait until this display is cleared before proceeding with the intended operation.
Ejecting the cassette tape
While the power is still on, press the EJECT button to open the cassette holder, and take out the cassette tape. If another cassette is not going to be loaded immediately after this tape is ejected, close the cassette holder.
Ejecting the cassette when the battery has no charge
First, set the POWER switch to OFF to turn off the unit’s power. Then turn the power back on, and immediately hold down the EJECT button. The cassette can be removed when there is still some power left in the battery. However, do not repeat this operation.
To prevent accidental erasure
Set the cassettes tab to SAVE to prevent the recordings on the tape from being erased accidentally.
2
Press the EJECT button. The cassette holder opens.
3
Insert the cassette tape and press the part marked with the arrow to close the cassette holder securely.
<Note>
Check that there is no slack in the tape of the cassette.
REC
SAVE
HUMID display
POWER: ON
EJECT button
Cassette holder
Checking for tape slack
Gently push in the reel using your finger and turn the reel in the direction of the arrow. If the reel fails to turn, it means there is no tape slack.
Chapter 3 Recording and playback
20
3-2 Basic procedures
This section describes the basic steps for shooting and recording. Before actually departing to shoot scenes, carry out inspections to ensure that the system is functioning properly.
* For details on how to perform these inspections, refer to 6-1
Inspections prior to shooting.
From providing the power supply to loading the cassette
Up to performing the switch settings
Provide the power supply, and load the cassette. Next, set each switch as shown in the figure below, and then proceed to operate.
1
Attach a fully charged battery pack.
2
Set the POWER switch to ON. Now check that the HUMID display is not showing and that at least 5 segments of the remaining battery charge display are lighted.
If the HUMID display is showing, wait until it goes off.When five or more segments of the remaining battery
charge display have not lighted, first check the battery setting. If there is nothing wrong with the battery setting, replace the existing battery pack with a fully charged battery pack.
3
Check that there are no cables around the cassette holder or top panel, and then press the EJECT button to open the cassette holder.
4
After checking the following points, insert the cassette tape and close the cassette holder.
Position of the accidental erasure prevent tabTape slack
1
2
2
3
4
Switch settings for shooting and recording
AUDIO SELECT CH 1/CH 2:
AUTO
TCG:
F-RUN or R-RUN
OUTPUT:
CAM/AUTO KNEE ON
GAIN:
Normally set to 0 dB; change to a more suitable value if the picture is too dark.
Aperture:
Automatic
Chapter 3 Recording and playback
3
21
Procedure for shooting
From adjusting the white balance and black balance to stopping the recording
1
Select the filter to match the lighting conditions.
2-1
If the white balance has been stored in the memory ahead of time:
Set the WHITE BAL switch to “A” or B.
2-2
If the white balance and/or black balance have not been stored in the memory and there is no time to adjust the white balance:
Set the WHITE BAL switch to PRST. The white balance for the filter is achieved in accordance with the setting position of the FILTER control (outer).
2
-3
When adjusting the white balance on the spot:
Select the filter to match the lighting conditions, set the WHITE BAL switch to “A” or “B” and adjust the white balance as follows:
1 Press the AUTO W/B BAL switch to the AWB
position and adjust the white balance.
2 Press the AUTO W/B BAL switch to the ABB
position and adjust the black balance.
3 Press the AUTO W/B BAL switch to the AWB
position and adjust the white balance again.
* For details on how to perform the adjustments, refer to 4-1-1
Adjusting the white balance and 4-1-2 Adjusting the black balance.
3
Point the camera at the subject, and adjust the focus and zoom.
4
When the electronic shutter is to be used, set the shutter speed and operating mode.
* For further details, refer to 4-2 Setting the electronic shutter.
5
Press the VTR START button or lens VTR button to start recording. During recording, the REC lamp inside the viewfinder lights.
6
To stop the recording, press the VTR START button again. The REC lamp inside the viewfinder goes off.
From adjusting the white balance and black balance to stopping the recording
132-1, 2, 32-34 5, 6
Tape function buttons
During recording, the tape function buttons (EJECT, REW, FF, PLAY/PAUSE and STOP) will not work.
Chapter 3 Recording and playback
22
3-3
Scene-to-scene continuity
Maintaining continuity from one scene to the next at an accuracy of +1 frame or less can be assured simply by pressing the VTR START button or VTR button on the lens while the unit is in the rec-pause mode. If the unit is in a mode other than rec-pause, the point at which the scene-to-scene continuity is to be maintained must be located before recording is started.
Scene-to-scene continuity during rec-pause
The scene-to-scene continuity timing is located automatically. However, the time taken until the start of recording differs depending on the setting of the VTR SAVE/STBY switch. When the VTR SAVE/STBY switch is set to SAVE,
recording commences about two seconds after the VTR START button is pressed.
When the VTR SAVE/STBY switch is set to STBY,
recording commences as soon as the VTR START button is pressed.
Ensuring scene-to-scene continuity after the power was turned off while the unit was in the rec-pause mode
3-4 NEWS REC function
The NEWS REC function is set using the NEWS REC MODE item after opening the <REC FUNCTION> screen from the SYSTEM SETTING page by performing menu operations. By controlling the VTR START button acknowledgment time during recording (by up to 2 seconds), the time taken for the unit to transfer from the recording mode to the rec-pause mode can be delayed. In other words, by controlling the VTR START button operation acknowledgment time, the unit can continuously record without the user having to interrupt the recording: this safeguards against the failure to record those precious momentsa failure that occurs when recording is resumed immediately after it was shut down temporarily.
SDC615
Ensuring scene-to-scene continuity at other times
Proceed as follows either after the tape has been allowed to run or after the cassette has been ejected or when ensuring continuity on a tape which has been recorded only in part.
1
Switch the power back on.
2
Press the VTR START button or lens VTR button to start the recording.
2
1
1
While monitoring the viewfinder screen, press the PLAY/PAUSE button to play back the tape.
2
At the place on the tape where continuity is to be maintained, press the PLAY/PAUSE (or STOP) button again to stop the tape.
3
Press the lens RET button. It takes about two seconds to complete the preparations for the scene-to-scene continuity.
4
Press the VTR START button or lens VTR button to start the recording.
1,2
3
4
It is also possible for the function of the VTR START button or VTR button on the lens to be allocated to the USER MAIN, USER1 or USER2 button. For details, refer to 4-8-4 Allocating functions to the USER MAIN, USER1 and USER2 buttons.
Real-time video signals Real-time audio signals
Recording on tape
REC start
REC start
REC/
pause
A
A
B
B
C
AC
C
t
When the NEWS REC function is ON
When the NEWS REC function is OFF
t = When this is inside the NEWS REC time setting
Chapter 3 Recording and playback
3
23
3-6 INTERVAL REC function
The AJ-SDC905 enables recording in intervals with a minimum recording time in increments of one frame to be conducted. The AJ-SDC615 enables recording in intervals with a recording time of 2 seconds or more to be conducted. In order for this function to be used, it is necessary by performing menu operations to open the <REC FUNCTION> screen from the SYSTEM SETTING page, select the interval recording mode using the INTERVAL REC MODE item, and set the recording time (REC TIME), interval pause time (PAUSE TIME) and time required for shooting (TOTAL TAKE TIME). Upon completion of the settings, the total shooting time (TOTAL REC TIME) is automatically calculated and displayed. The INTERVAL REC MODE item settings are described below.
OFF: Interval recording is not performed. ON: Interval recording is performed. ONE SHOT:
One-shot interval recording is performed for the time which was selected by the REC TIME setting.
Procedure for shooting in the ON modes of INTERVAL REC
SDC615
SDC905
1
After performing the basic operations for shooting and recording as set forth in 3-2 Basic procedures, secure the unit in such a way that it will not move.
2
Press the units VTR START button or the VTR button on the lens. Interval recording now starts. When the set TOTAL TAKE TIME has elapsed, recording is ended automatically. As mentioned in 2-7 Display window and its displays,” “i” flashes when the INTERVAL REC mode is selected. As soon as recording starts, iREC lights. During rec-pause, iREC flashes. Exactly what mode is established in the unit can be ascertained by observing these displays. The same displays as the ones in the display window also appear inside the viewfinder, and the TALLY lamp lights while recording is underway. Further, when the pause time has been set to 2 minutes or more, the tally lamp blinks at 5 second intervals to inform the operator. Further, when pause time has been set to 2 minutes or more, the tally lamp blinks at 5 second intervals to indicate when recording is paused. Under these conditions, the tally lamp will also flash 3 seconds before recording starts.
A
A
B
B
C
Real-time video signals Real-time audio signals
Real-time video signals Real-time audio signals
What is recorded on the tape
Previous cut
PRE-REC time set
REC start
(recording start)
REC pause
1
122
3
3
N
N
t1
t1
t2 t2
t1
t1
t2
t1
N-1
N-1
What is recorded on the tape
iREC start Time base
REC TIME (recording
time = t1)
TOTAL TAKE TIME
(time required for shooting)
TOTAL REC TIME
(time during which signals are recorded on tape)
PAUSE TIME
(pause time
= t2)
3-5
PRE-RECORDING function
By always storing a few seconds worth (maximum of 6 seconds) of audio and video data shot by the camera, it is possible to record video and audio signals a number of seconds before recording is actually started by pressing the VTR START button or the VTR button on the lens. In order for this function to be used, it is necessary to open the <REC FUNCTION> screen from the SYSTEM SETTING page and set the data storage time in the memory using the PRE REC MODE item by performing menu operations. The PRE REC MODE item settings are described below.
OFF: The PRE-RECORDING function is not activated. 0-6SEC: A value from 1 to 6 seconds is set as the length of
time for which the video and audio signals can be recorded before the VTR START button or VTR button on the lens is pressed.
SDC905
<Notes>
The data contained in the storage memory becomes
unstable immediately after the power is turned on, immediately after the PRE REC MODE item setting is selected or its set time has been changed, and immediately after playback or rec-review has been performed. Immediately after any of these operations, therefore, the video and audio signals will not be pre-recorded for the duration set when recording is started by pressing the VTR START button or VTR button on the lens.
The video data and audio data are not stored in the storage
memory while playback or rec-review is being performed. This means that the pre-recording will not include the video and audio signals supplied during a playback or rec-review operation.
Since it will take a few moments for recording to commence
when the unit is in the tape protection mode, the pictures and sound will not be recorded at the time which has been set.
The pre-recording function will not work when the
<SYSTEM MODE> screen is opened from the SYSTEM SETTING page by performing menu operations and 1394 is selected as the REC SIGNAL menu item setting.
When recording has been started, the time code (TCG)
display may remain in the hold status until it is possible for the time code (TCR) on the tape to be read.
Chapter 3 Recording and playback
24
When recording is to be suspended at any time
Press the STOP button. Recording is now suspended. O With the AJ-SDC905 , the tape may continue to
run since the unit will record the images stored in the memory until the moment when the button is pressed.
When the recording is to be continued
Press the units VTR START button or VTR button on the lens once more. Interval recording is now started again.
When the INTERVAL REC mode is to be exited
There are two ways to do this.
1) Set the units POWER switch to OFF.
2) Perform a menu operation and select OFF as the INTERVAL REC MODE item setting.
Procedure for shooting in the ONE SHOT mode
Follow the procedure below for shooting after the settings for the interval recording mode have been completed.
SDC905
1
After performing the basic operations for shooting and recording as set forth in 3-2 Basic procedures, secure the unit in such a way that it will not move.
2
Press the units VTR START button or the VTR button on the lens. When the set REC TIME has elapsed, the recording is ended automatically. As mentioned in 2-7 Display window and its displays,” “i” flashes when the INTERVAL REC mode is selected. As soon as recording starts, iREC lights. When the recording ends, iREC flashes. The same displays as the ones in the display window also appear inside the viewfinder, and the TALLY lamp lights while recording is underway.
When the recording is to be continued
Press the units VTR START button or VTR button on the lens once more. One-shot recording is now started again.
When the ONE SHOT mode of INTERVAL REC is to be exited
There are two ways to do this.
1) Set the units POWER switch to OFF.
2) Perform a menu operation and select OFF as the INTERVAL REC MODE item setting.
Checkpoints common to all INTERVAL REC modes
The interval recording function will not work when the
<SYSTEM MODE> screen is opened from the SYSTEM SETTING page by performing menu operations and 1394 is selected as the REC SIGNAL menu item setting.
Sound-related
Whether the sound is to be recorded or not during interval recording is set by setting ON or OFF for the AUDIO REC item on the <REC FUNCTION> screen.
Tape function button-related
During interval recording, all the tape function buttons (EJECT, REW, FF and PLAY/STILL) except STOP do not work.
Starting recording quickly when unit is in pause mode
Selecting REC as the setting for one of either USER MAIN or USER1/USER2 buttons in advance enables quick start recording during pause mode when the set button is pressed. Measurement of pause mode time is continued even after quick start recording.
When the units power was turned off during recording
If the units POWER switch was set to the OFF position during interval recording with the use of the memory, the tape will continue to run in order to record the video signals which were stored in the memory until the moment when the POWER switch was set to OFF, and then the power will automatically go off. If the battery was removed, the DC cable was disconnected or the power supplied through the AC adapter was cut off during recording, those shots (up to 6 seconds) taken prior to the moment concerned may not be recorded. Bear this in mind when the battery is to be replaced.
When the tape has run out during recording
Bear in mind that if the tape has run out and stops during interval recording with the use of the memory, those shots (up to 6 seconds) taken prior to the moment when the tape stopped may not be recorded.
With the AJ-SDC905 , if a PLAY, FF or REW
operation is performed after one-shot recording, the operation will be performed after the images remaining in the memory are written on the tape. While the images are being recorded, the LED of the button pressed (for play, FF or REW operation) will flash.
Concerning the time code display
When recording has been started, the time code (TCG) display may remain in the hold status until it is possible for the time code (TCR) on the tape to be read.
SDC905
SDC905
SDC905
SDC905
Real-time video signals
Real-time audio signals
What is recorded on the tape Previous cut
iREC
start
A
t
A
REC TIME
(recording time = t1)
Time base
Chapter 3 Recording and playback
3
25
3-7 RETAKE function
The RETAKE function ensures continuity with the previous cut on the tape when shooting is resumed. It is set by opening the <REC FUNCTION> screen from the SYSTEM SETTING page and selecting ON as the setting for the RETAKE MODE item by performing menu operations.
The RETAKE MODE item settings are described below. ON: The retake operation is performed when the RET button
on the lens is pressed while the MODE CHECK button is held down.
OFF: The RETAKE function does not operate.
If, when the rec-pause mode is established upon completion of the recording or the stop mode is established afterwards, the RET button on the lens is pressed while the MODE CHECK button is held down, the tape will be rewound to the approximate start point (a position advanced by 10 or so frames from the recording start) of the final image that was last recorded, and the rec-pause mode will be established. If there is some leeway in the shooting time and a NG condition has been clearly identified, recording can be started from this point, and the cut in the NG area will be deleted. This function is particularly useful for cutting the amount of time taken for copying onto work tapes and other such economical operations.
3-9 Normal playback and playback at
different speeds
Black-and-white playback images can be viewed in the viewfinder by pressing the PLAY button. At the same time, color playback images can be viewed if a color video monitor is connected to the units VIDEO OUT connector and MON OUT connector. In order to view these images, the OUTPUT SEL switch on
the side panel must be set to the VTR position.
In addition, when the FF and REW buttons are used, the images can be played back at different speeds by establishing the cue mode (PLAY + FF), review mode (PLAY + REW), high-speed fast forward playback mode (FF) or high-speed rewind playback mode (REW).
3-8 Rec-review function
When recording is temporarily stopped and the lens RET button is pressed, the last two seconds of the tape are automatically rewound, and the playback pictures on this part of the tape appear on the viewfinder screen. This makes it possible to check whether recording was performed properly. After the two seconds of the tape have been played back, the unit is again set to the recording start standby mode. If the RET button is held down, a maximum of 10 seconds of the tape is rewound and played back. The RET button function can be allocated by opening the <USER SW> screen from the OPERATION page and selecting settings for the USER MAIN SW, USER1 SW and USER2 SW items by performing menu operations.
<Note>
The rec-review function cannot be used unless recording
lasts for one or more seconds.
If the OUTPUT SEL switch on the side panel is at the VTR
position during the rec-review operation, the rec-review images are output not only to the viewfinder but to the video output connectors (VIDEO OUT connector and MON OUT connector) as well. Bear in mind that if back-up images are being recorded by a backup VTR that has been connected, these rec-review images will end up being recorded.
When the RETAKE function is to be exited
There are two ways to do this.
1) Set the units POWER switch to OFF.
2) Perform a menu operation and select OFF as the RETAKE MODE item setting.
Direction of tape travel
Approx. 10 frames
Cut 1 Cut 2
Cut 1 Cut 2
Cut 3
Cut 3
Cut 4
Direction of tape travel
Playback of recorded section
Recording section
2 to 10 sec.
No recorded or already recorded section
Rec-pause
Rec-pause
Rec-review operation
Chapter 4
Adjustments and settings for recording
26
In order to achieve images with a consistently high picture quality with this unit, it is necessary to adjust the black balance and white balance as the individual conditions demand. To achieve a higher picture quality, it is recommended that the adjustments be performed in the following sequence: AWB (white balance adjustment) > ABB (black balance adjustment) > AWB (white balance adjustment).
4-1
Adjusting the white balance and black balance
4-1-1 Adjusting the white balance
The white balance must always be re-adjusted when the lighting conditions have changed. The white balance is adjusted automatically by following the steps below.
White balance detection area
The white balance detection area setting can be changed to 90%, 50% or 25% by opening the <WHITE BALANCE MODE> screen from the OPERATION page and selecting the desired setting for the AWB AREA item by performing menu operations. The factory setting is 25%.
1
Set the switches as shown in the figure.
2
Select the FILTER control setting in accordance with the lighting conditions.
<Note>
For examples of the FILTER control settings, refer to 2-3 Shooting and recording/playback function section.
3
Erect a white pattern at a place with the same conditions as the source of light illuminating the subject, zoom in, and shoot the white of the pattern on the screen. A white object (such as a white cloth or white wall) near the subject may be used as a substitute for the white pattern. The size of the white object required is shown in the figure below.
<Notes>
Take care to keep high-brightness spots off the screen.Shoot white objects in the center of the screen.
4
Adjust the lens aperture.
5
Set the AUTO W/B BAL switch to AWB, and then release it. The switch returns to the center, and the white balance is automatically adjusted.
<Note>
When the AUTO W/B BAL switch is pressed again to the AWB side when the white balance is being adjusted automatically (AWB ACTIVE), the adjustment operation will stop. The adjusted value in this case is the value before automatic adjustment was performed.
6
While the adjustment is in progress, the following message appears on the viewfinder screen.
At least one-fourth of the screen width
At least one-fourth of the screen height
AWB ACTIVE
7
Adjustment is completed in several seconds. (A message similar to the one shown in the figure below now appears.) The adjustment value is automatically saved in the memory (A or B) which was set in step 1.
AWB A OK 3.2K
8
The message shown in the figure below appears when the color temperature of the subject falls below 2300 K or rises above 9900 K. The downward pointing arrow indicates that the color temperature is lower than the display temperature; conversely, an upward pointing arrow indicates that the it is higher than the display temperature.
AWB A OK 2.3K
m
90%
50%
25%
FILTER control
WHITE BAL: A or B
OUTPUT: CAM
GAIN: Normally 0 dB
Set to a more suitable gain level if it is too dark.
AUTO W/B BAL switch:
Use this to execute AWB.
4
Chapter 4
Adjustments and settings for recording
27
When there is no time to adjust the white balance
Set the WHITE BAL switch to PRST. The white balance for the filter is achieved in accordance with the setting position of the FILTER control (outer).
When the white balance cannot be adjusted automatically
When the white balance adjustment was not completed correctly, one of the following error messages will appear on the viewfinder screen. When an error message is displayed, take the recommended action, and try adjusting the white balance again. If the error message persists even after repeated attempts, the inside of the unit must be inspected. For details, contact your nearest service center or your dealer.
Auto tracking white balance setting
This unit comes with an auto tracking white balance (ATW) function for automatically tracking the white balance of the images in accordance with the lighting conditions. This function can be set in WHITE BAL switch B. Open the <WHITE BALANCE MODE> screen from the OPERATION page and select ATW for the <AWB B> item by performing menu operations. The ATW function can also be allocated to the USER MAIN, USER1 or USER2 button. For details, refer to 4-8-4 Allocating functions to the USER MAIN, USER1 and USER2 buttons.
To release the auto tracking white balance
Either press again the USER button to which ATW has been allocated or select a different position for the WHITE BAL switch.
#
< WHITE BALANCE MODE >
FILTER INH :ON SHOCKLESS AWB :NORMAL AWB AREA :25%
AWB&ABB OFFSET :OFF AWB A :MEM COLOR TEMP A :3200K AWB B :MEM COLOR TEMP B :3200K ATW SPEED :NORMAL
<Note>
This function is not meant to give a 100% guarantee for the accuracy of the white balance. Some leeway has been given to both the functions ability to track changes in the lighting conditions and the accuracy with which the white balance is tracked. For this reason, handle the function carefully.
Viewfinder screen displays relating to the white balance
For details, refer to 4-7 Viewfinder screen status displays.
Messages relating to white balance adjustment
Error
message
Meaning Recommended action
Select a suitable filter.
COLOR TEMP. HIGH
Color temperature is too high.
Select a suitable filter.COLOR TEMP.
LOW
Color temperature is too low.
Increase the amount of light or increase the gain.
LOW LIGHT There is not enough light.
Reduce the amount of light or reduce the gain.
LEVEL OVER There is too much light.
Check the filter selector control.
CHECK FILTER The setting position of the
filter selector control is not correct.
The shooting conditions may be unstable. If flicker occurs, engage the shutter and shoot again under stable conditions.
TIME OVER AWB was not completed
within the allotted time.
White balance memories
The values stored in the memories are retained even after the units power has been turned off until the white balance is next adjusted. There are two sets of white balance memories, A and B. When ON has been selected (initial setting) as the setting for the FILTER INH item on the <WHITE BALANCE MODE> screen opened from the OPERATION page by performing menu operations, the number of memories is limited to one in A and one in B. In this case, the memory contents are not coupled with the CC filter. When FILTER INH is set to OFF, the adjustment values for each CC filter can be automatically saved in the memories corresponding to the WHITE BAL switch settings (A or B). This unit contains four filters so that a total of 8 (4a2) adjustment values are saved. Note that when VAR has been selected for AWB A and AWB B items of the <WHITE BALANCE MODE> screen, the values will be the fixed color temperature settings established with the COLOR TEMP A and COLOR TEMP B settings and they cannot be adjusted using the AWB switch.
Chapter 4
Adjustments and settings for recording
28
<Notes>
Check that the lens connector has been connected and
that the lens aperture is set to CLOSE.
While the black balance is being adjusted, the aperture
is automatically set to the light-shielding status.
While the black balance is being adjusted, the gain
selector circuit is switched automatically. Flicker or noise may appear on the viewfinder screen, but this is not indicative of malfunctioning.
If the black shading is still unsatisfactory although the
ABB OK message is displayed, perform menu operations to open the <BLACK SHADING> screen from the MAINTENANCE page, move the arrow mark (>) to the DETECTION item, press the JOG dial button, and proceed with the black shading adjustment. If the ABB switch is held down for 5 or more seconds, the black shading can be automatically adjusted after the ABB operation. (See the SHD.ABB SW CTL item under 7-5-5 SW MODE.”)
If the AUTO W/B BAL switch is pushed down to the
ABB position again while the black balance is being automatically adjusted (ABB ACTIVE), the adjustment will be aborted. The adjusted value in this case is the value before automatic adjustment was performed.
Black balance memory
The values stored in the memory are retained even after the units power has been turned off.
4-1-2 Adjusting the black balance
The black balance needs to be adjusted in the following cases:
When the unit is used for the first timeWhen the unit is used after it has not been used for a
prolonged period of time
When the unit is used in an ambient temperature which has
fluctuated significantly
When the value selected for the gain switch has been
changed
When the super gain setting has been performed using the
USER MAIN, USER1 or USER2 button
When the gamma ON/OFF setting has been changed
1
Set the switches as shown in the figure.
2
Set the AUTO W/B BAL switch to the ABB position, and then release it. The switch returns to the center, and the adjustment is performed.
3
While the adjustment is in progress, the following message appears on the viewfinder screen.
<Note>
While the adjustment is in progress, the lens aperture is automatically set to CLOSE.
AUTO W/B BAL switch:
Use this to execute ABB.
OUTPUT: CAM
ABB ACTIVE
4
Adjustment is completed in several seconds. (A message similar to the one shown in the figure below now appears.) The adjustment value is automatically saved in the memory.
ABB OK
4
Chapter 4
Adjustments and settings for recording
29
4-2
Setting the electronic shutter
This section describes the units electronic shutter, its settings and operations.
4-2-1 Shutter modes
The table below lists the shutter modes in which the unit’s electronic shutter can be used as well as the shutter speeds which can be selected.
Mode Shutter speed Applications
For shooting fast-moving subjects clearly.
For improving the vertical resolution.
Standard
SUPER V
POSITION1 - 6
For shooting monitor screens with a vertical scanning frequency exceeding 60 Hz in a way that minimizes the pattern of horizontal lines.
SYNCHRO SCAN
Within the
60.3
Hz to
249.7
Hz range
<Notes>
O No matter in which mode the electronic shutter is used, the
higher the shutter speed, the lower the cameras sensitivity.
O When the aperture is in the automatic mode, it will
increasingly open and the depth of focus will become shallower as the shutter speed is increased.
O The electronic shutter will not function when the cumulative
gain-boosting DS. GAIN (digital super gain) mode is in use.
4-2-2 Setting the shutter mode and speed
The shutter speeds used in the shutter mode are set by switching the SHUTTER switch. The shutter speeds in the SYNCHRO SCAN mode can easily be changed using the SYNCHRO SCAN (+ and -) buttons on the side panel. Open the <SHUTTER SPEED> screen and <SHUTTER SELECT> screen from the OPERATION page by performing menu operations. It is now possible to restrict the shutter speed selection range to the required range beforehand and/or select whether to use the SYNCHRO SCAN mode and SUPER V mode beforehand. Once selected, the shutter speed is retained even after the units power has been turned off.
#
< SHUTTER SPEED >
SYNCHRO SCAN :ON SUPER V :OFF POSITION1 :ON POSITION2 :ON POSITION3 :ON POSITION4 :ON POSITION5 :ON POSITION6 :ON
#
< SHUTTER SELECT >
SUPER V MODE :FRM1 POSITION1 SEL :1/100 POSITION2 SEL :1/120 POSITION3 SEL :1/250 POSITION4 SEL :1/500 POSITION5 SEL :1/1000 POSITION6 SEL :1/2000
1
Press the SHUTTER switch from ON to SEL.
SHUTTER switch
2
Press the SHUTTER switch to the SEL position again, and repeat this until the desired mode or speed is displayed. When all the modes and speeds are displayed, the display will change in the sequence shown below.
<Note>
Since the factory setting for the SUPER V mode is OFF, there is no display at this setting. To designate the mode, open the <SHUTTER SPEED> screen from the OPERATION page and select ON for the SUPER V item setting by performing menu operations.
Viewfinder screen displays relating to the shutter
For details, refer to 4-7 Viewfinder screen status displays.
POSITION
1
POSITION2POSITION3POSITION4POSITION5POSITION
6
Standard mode
SUPER V
mode
SYNCHRO SCAN
mode
Chapter 4
Adjustments and settings for recording
30
4-3 Selecting the recording signals
and recording system
With this unit, both the signals to be recorded and the recording format can be selected.
4-3-1
Selecting the recording signals
Open the <SYSTEM MODE> screen from the SYSTEM SETTING page and select the signals to be recorded using the CAMERA MODE item by performing menu operations.
Items to be set and what is set
The signals to be recorded are selected using REC SIGNAL.
CAM: The signals from the camera are recorded. VIDEO: The signals from the GENLOCK IN connector are
recorded. The images may be disrupted when the signals from the GENLOCK IN connector are non-standard signals.
1394: The signals from the DVCPRO connector are
recorded.
Bear the following points in mind when 1394 is selected as the setting.
O Connect the unit to external units on a 1-on-1 basis. O The sound is recorded using the audio signals supplied to
the DVCPRO connector but its input level cannot be adjusted. At a time like this, nothing is recorded on the cue track.
O The cue signals cannot be input or output. O When the TCG switch is at the F-RUN position, the time
code supplied to the DVCPRO connector is recorded.
O When the TCG switch is at the R-RUN position, the
recording is performed using the time code which has been recorded on the tape.
O When EXT is selected as the UB MODE item setting on the
<TC/UB> screen by performing menu operations, the user bits which are supplied to the DVCPRO connector are recorded.
O The user bits which are supplied to the DVCPRO
connector are recorded in the vertical blanking period regardless of the VITC UB MODE item setting.
O It is not possible to record the time code which is supplied
to the TC IN connector.
O The time code which is output from the TC OUT connector
is not synchronized with the video output signals or the output signals from the DVCPRO connector.
O The signals which are output from the VIDEO OUT
connector, MON OUT connector or AUDIO OUT connector differ from the actual signals. Use them for monitoring purposes.
O It is not possible to use the GENLOCK IN connector to
achieve synchronization with the external reference signal.
O The signals may be disrupted when the power of the
connected units is switched from ON to OFF or vice versa or when the interface cable is connected or disconnected.
O It may take several seconds for the system to stabilize
immediately after the input signals are switched or immediately after the operation mode is changed, for instance. Wait until the system has stabilized before proceeding with recording.
O Supply normal playback speed (1k speed) signals. When
playback signals of any other speed are supplied, the images and sound may not be recorded properly.
O The pre-recording function and Interval REC
function do not work.
O Characters other than the ones that are used in the menus
are not displayed on the viewfinder screen and output images. Similarly, the same are not displayed when VIDEO is selected.
SDC905
1
Press the SHUTTER switch from ON to SEL to establish the SYNCHRO SCAN mode.
2
In the SYNCHRO SCAN mode, it is possible to change the shutter speed continuously within a range from 1/60.3 sec. to 1/249.7 sec. by operating the SYNCHRO SCAN (+ and –) buttons.
4-2-3
Setting the synchro scan mode
Proceed with operation by following the steps below.
SYNCHRO SCAN (+ and –) buttons
SHUTTER switch
#
< SYSTEM MODE >
REC SIGNAL :CAM REC MODE :16:9/50M SET UP 50 :7.5%A SET UP 25 :7.5%A PB MODE :AUTO REC TALLY :RED
SDC905
#
< SYSTEM MODE >
REC SIGNAL :CAM ASPECT :16:9 SET UP :7.5%A PB MODE :AUTO REC TALLY :RED
SDC615
Loading...
+ 78 hidden pages