PackardBell M5850 User Manual
I
ixtreme M5850
Service Guide
PRINTED IN TAIWAN
II
Revision History
Please refer to the table below for the updates made on ixtreme M5850 series guide.
Date Chapter Updated
III
Copyright
Copyright © 2010 by Acer Incorporated. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranties of merchantability or fitness for any
particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is".
Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its
distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or
consequential damages resulting from any defect in the software.
IV
Conventions
The following conventions are used in this manual:
SCREEN
MESSAGES
NOTE
Denotes actual messages that appear
on screen.
Gives bits and pieces of additional
information related to the current
topic.
WARNING
CAUTION
IMPORTANT
Alerts your to any damage that might
result from doing or not doing specific
actions.
Gives precautionary measures to
avoid possible hardware or software
problem.
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
V
Preface
Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC
CONFIGURATION decided for Acer's "global" product offering. To better fit local market
requirements and enhance product competitiveness, your regional office MAY have decided to
extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases,
please contact your regional offices or the responsible personnel/channel to provide you with
further technical details.
2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date
information available on your regional web or channel. If, for whatever reason, a part number
change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED
SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those
given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional
Acer office to order FRU parts for repair and service of customer machines.
VI
Introducing the Motherboard................................................錯誤! 尚未定義書籤。
Features...................................................................................................2
Mainboard Components........................................................................4
Block Diagram........................................................錯誤! 尚未定義書籤。
ixtreme M5850 ......................................................................................5
I/O Port Introduction..............................................................................9
Hardware Specifications and Configurations.......錯誤! 尚未定義書籤。
Using BIOS...............................................................................................................16
Setup Utility Menus...............................................錯誤! 尚未定義書籤。
Product Information..............................................錯誤! 尚未定義書籤。
Standard CMOS Features.......................................錯誤! 尚未定義書籤。
Advanced BIOS Features........................................錯誤! 尚未定義書籤。
Advanced Chipset Features...................................錯誤! 尚未定義書籤。
Integrated Peripherals...........................................錯誤! 尚未定義書籤。
Power Management Setup...................................錯誤! 尚未定義書籤。
PC Health Status.....................................................錯誤! 尚未定義書籤。
Frequency/Voltage Control...................................錯誤! 尚未定義書籤。
BIOS Security Features...........................................錯誤! 尚未定義書籤。
Load Default Settings............................................錯誤! 尚未定義書籤。
Machine Disassembly and Replacement................................................................30
General Information.............................................................................31
Standard Assembly Process..................................................................32
Standard Disassembly Process...............................錯誤! 尚未定義書籤。
Troubleshooting.....................................................................................................66
Power-On Self-Test (POST)...................................................................67
POST Error Messages List......................................................................71
Error Symptoms List..............................................................................73
Undetermined Problems......................................................................77
Jumper and Connector Information......................................................................78
FRU (Field Replaceable Unit) List.........................................................................92
Exploded Diagram................................................................................92
FRU List..................................................................................................98
1
Introducing the Motherboard
Introduction
Thank you for choosing the H67 motherboard. This motherboard is a high performance, enhanced
function motherboard designed to support the LGA1155 socket for 2nd Generation IntelR CoreTM
Family/PentiumR/CeleronR processors for high-end business or personal desktop markets.
This motherboard is based on IntelR H67 Chipset for best desktop platform solution. H67 is a single-chip,
highly integrated, high performance Hyper-Threading peripheral controller, unmatched by any other single
chip-device controller. This motherboard supports up to 16 GB of system memory with dual channel DDR3
1333/ 1066 SDRAM. Two PCI are supported, fully compliant with PCI rev 2.2 specification at 33MHz. High
resolution graphics via PCI Express x16 slot, intended for Graphics Interface, is fully compliant to the PCI
Express Base Specification revision 2.0. In addition, one PCI Express slot is supported. It implements an
EHCI (Enhanced Host Controller Interface) compliant interface that provides fourteen USB 2.0 ports (six
USB 2.0 ports at the back panel and four USB 2.0 headers support additional eight USB 2.0 ports).
The motherboard is equipped with advanced full set of I/O ports in the rear panel, including PS/2 mouse
and PS/2 keyboard connectors, one DVI(co-lay HDMI) port, one D_sub (VGA) port, one Lan port, six USB
2.0/3.0 ports, and audio jacks for microphone, line-in and line-out. In addition, this motherboard supports
two SATA 6Gb/s connectors and four SATA 3Gb/s connectors.
Chapter1
2
Features
Operating system
Windows®7 Home Premium x86/x64, Windows® 7 Home Basic x86, Windows®7 Starter x86
Processor
The motherboard uses an LGA1155 type of socket that carries the following
Features:
l Accommodates 2nd Generation IntelR CoreTM Family / PentiumR / CeleronR processors
l Supports “Hyper-Threading” technology CPU
l One PCI Express x16 Gen2 port supporting up to 5 GB/s direction peak bandwidth
“Hyper-Threading” technology enables the operating system into thinking it’s hooked up to two processors,
allowing two threads to be run in parallel, both on separate “logical” processors within the same physical
processor.
Chipset
The Intel H67 Express Chipset is a single-chip with proven reliability and performance.
l Support one PCI Express slot
l Integrated two SATA 6.0 Gb/s Host Controller
l Integrated two SATA 3.0 Gb/s Host Controller
l Fourteen USB 2.0 ports supported
l Serial Peripheral Interface (SPI) support
l Integrated Graphics Support with PAVP 1.5
l • Intel® High Definition Audio Controller
Memory
l Supports DDR3 1333/1066 DDR3 SDRAM with Dual-channel architecture
l Accommodates four unbuffered DIMMs
l Up to 4 GB per DIMM with maximum memory size up to 16 GB
Onboard LAN
The onboard LAN provides the following features:
l Supports PCI ExpressTM 1.1
l Integrated 10/100 /1000 transceiver
l Wake-on-LAN and remote wake-up support
Audio
l 5.1 Channel High Definition Audio Codec
l ADCs support 44.1k/48k/96kHz sample rate
l Meets Microsoft WLP 3.10 Vista premium and mobile PCs audio requirements
l Direct Sound 3DTM compatible
Expansion Options
The motherboard comes with the following expansion options:
l One PCI Express x16 slot for Graphics Interface
l Three PCI Express x1 slot
l Six SATA connectors
3
Integrated I/O
The motherboard comes with the following expansion options:
l Two PS/2 ports for mouse and keyboard
l One VGA port
l One HDMI port
l Six USB ports
l One LAN port
l Audio jacks for microphone, line-in and line-out
BIOS Firmware
The motherboard uses AMI BIOS that enables users to configure many system features including the
following:
l Power management
l Wake-up alarms
l CPU parameters
l CPU and memory timing
l Graphic parameters
The firmware can also be used to set parameters for different processor clock speeds.
1. Some hardware specifications and software items are subject to change
without prior notice.
2. Due to chipset limitation, we recommend that motherboard be operated
in the ambiance between 0 and 50 ° C.
Dimensions and weight
l 355 (H) x 382.5(D) x 180(W) mm (without bezel)
l 11.4Kg
4
Mainboard Components
No Label Component
1 CPU Socket AMD socket
2
ATX_12V Auxiliary 4-pin power connector
3 SYS_FAN System cooling fan connector
4 CPU_FAN CPU cooling fan connector
5 DIMM1~4 240-pin DDR3 SDRAM slots
6
ATX1 Standard 24-pin ATX power connector
7
CLR_CMOS Clear CMOS jumper
8
ME_DISABLE ME disable header
9
LEDH1 Front panel switch/LED header
10
11
12
13
14
15
SATA1~6 Serial ATA connectors
F_USB1~4 Front panel USB headers
SPDIF_OUT SPDIF out header
F_AUDIO1 Front panel audio header
PCIE1Х-1~3 PCI Express x1 slot
PCIE16Х PCI Express x16 slot
This concludes Chapter 1. The next chapter explains how to install the motherboard.
5
Block Diagram
6
ixtreme M5850
The computer’s front panel consists of the following：
Front view
No Icon Component Description
1
2 xD
3 CF Compact flash.
4 MS/MS Pro
5 Micro SD Micro Secure Digital.
6 SD/MMC
7
8
USB ports.
MS: Memory Stick
MS Pro: Memory Stick PRO
SD Plus: Ultra II SD PLUS Memory
Card
MMC Plus: MultiMediaCard PLUS
Headphone/Speaker-out/line-out port.
Microphone-in jack. Accepts input from external microphones.
Connects to USB 2.0 devices
(e.g.,USB mouse, USB camera).
Connects to audio line-in devices
(e.g.,speakers,headphones).
9
USB ports.
Connects to USB 2.0 devices
(e.g.,USB mouse, USB camera).
7
Rear view
No Icon Component Description
1
2
3
4
5
6
7
8
HDMI HDMI Port
PS/2 keyboard connector
High Definition Multimedia Interface
USB 2.0 ports
Microphone jack
PS/2 mouse connector
Network port
Line-in jack
Line-out jack
Connects to USB 2.0 devices
(e.g., USB mouse, USB camera).
Accepts input from external
microphones.
Lights to indicate the status of wireless
LAN communications.
Accepts audio line-out devices
(e.g.,audio CD player,)
Accepts audio line-in devices
(e.g.,audio CD player,)
8
Audio Jack Function Table
Color/Use Headphone 2CH 4CH 5.1CH
Blue Line-in Line-in Rear Speaker Rear Speaker
Green Headphone Front speaker Front speaker Front speaker
Pink Mic-in Mic-in Mic-in Center & bass
9
I/O Port Introduction
The backplane of the motherboard has the following I/O ports:
No Component Description
1 PS2 Mouse
2 USB Ports Use the USB ports to connect USB devices.
Use the upper PS/2 port to connect a PS/2 pointing
device.
3 LAN Port
4 Line-in / Line-out / Microphone
5 PS2Keyboard Use the lower PS/2 port to connect a PS/2 keyboard.
6 HDMI Port Connect the HDMI port to the HDMI devices.
7 VGA Port Connect your monitor to the VGA port.
Connect an RJ-45 jack to the LAN port to connect your
computer to the Network.
Use the three audio ports to connect audio devices. The
first jack is for stereo line-in signal. The second jack is for
stereo line-out signal. The third jack is for microphone.
10
System Peripherals
The IXTREME M5850 series computer consist of the system itself, and system peripherals, like a
mouse, keyboard, card reader and a set of speakers (optional). This section provides a brief description
of the basic system peripherals.
Mouse (PS/2 or USB, manufacturing option)
The included mouse is a standard two-button wheel mouse. Connect the mouse to the PS/2 mouse port
or USB port on the back panel of the system.
Keyboard (PS/2 or USB, manufacturing option)
Connect the keyboard to the PS/2 keyboard port or USB port on the back panel of the system.
Speakers
For systems bundled with speakers, before powering on the system, connect the speaker cable to the
audio out (external speaker) port on the back panel of the system.
For more detailed information about the speakers, please refer to the included operating instructions.
NOTE: speakers are optional and the appearance might be different depending on the actual product.
11
Card Reader (Option)
Memory cards are used in a wide selection of digital cameras, PDAs, MP3 players and mobile phones.
Selected computers include an “all-in-one”memory card reader that allows you read and write the most
common types, such as SD (Secure Digital)™/ MMC (Multi Media Card™), CF (Compact Flash®), xD
(XD-PICTURE CARD), Micro SD and MS/MS Pro (Memory Stick®).
NOTE: Card reader are optional and the appearance might be different depending on the actual product.
12
Hardware Specifications and Configurations
Processor
Item Specification
Type
Socket
Speed
FSB
BIOS
Item Specification
BIOS code programmer Afudos
BIOS version P01-A0 (or newer version)
BIOS ROM type Flash ROM
BIOS ROM size 32MB
BIOS ROM package 32-pin DIP package(SST)
Support protocol
Boot from CD-ROM feature Yes
LGA1155 socket for 2nd Generation IntelR CoreTM
Family/ PentiumR/CeleronR processors
socket LGA1155
Depends on CPU which is configured
Depends on CPU which is configured
ACPI 2.0, APM 1.2, SMBIOS 2.3, WFM support,
ASD
Support to LS-120 FDD drive Yes
NOTE: The BIOS can be overwritten/upgraded by using the flash utility.
BIOS Hotkey List
Item Specification Specification
DEL Enter BIOS Setup Utility
F12 Enter Boot Menu
Press while the system is booting to enter BIOS
setup Utility.
Press while the system is booting to enter Boot
Menu.
Main Board Major Chips
Item Specification
Chipset Intel H67
AGP controller Intel H67
Super I/O controller ITE 8728F
Audio controller Realtek ALC662
LAN controller Intel 82579V
HDD controller Intel H67
Keyboard controller ITE 8728F
13
System Memory
Item Specification
Memory slot number
Support memory size per socket 1GB to 4GB
Support maximum memory size 16 GB
Support memory type DDR3 DRAM
Support memory interface DDR3 1066/1333
Support memory module package 240-pin DIMM
Support parity check feature Yes
Support to Error Correction Code (ECC) feature
Memory module combinations
NOTE: Dual channel should be enabled always when plug-in 2 same memory size DDRII memory module.
4 slots
ECC checking with double-bit detect and single-bit
correct
You can install memory modules in any
combination as long as they match the
specifications.
Cache Memory
Item Specification
First-Level Cache Configurations
Cache function control Always enabled
Second-Level Cache Configurations
L2 Cache RAM size Up to 2MB per core (exclusive)
L2 Cache RAM speed One-half the processor core clock frequency
L2 Cache function control Enable/Disable by BIOS Setup
Video Interface
Item Specification
Video controller Intel H67
Video controller resident bus PCIE
Video Interface X16
Audio Interface
Item Specification
Audio controller Realtek
Audio controller Type ALC662
Audio Channel 5.1ch
Audio function control Enable/disable by BIOS Setup
Mono or stereo 5.1 channel
Sampling rate DACs: 44.1k/48k/96k/192k Hz
MPU-401 UART support Yes
Microphone jack Supported
Headphone jack Supported
14
IDE Interface
Item Specification
IDE controller Intel H67
Number of SATA connector 4
Support bootable CD-ROM Yes
USB Port
Item Specification
Universal HCI USB 2.0/3.0
USB Class Support legacy keyboard for legacy mode
USB Number support up to 12 ports
Power Management
Devices
Power Button Enabled Enabled Enabled Disabled
USB Keyboard Enabled Enabled Enabled N/A
LAN Disabled Disabled Disabled Disabled
RTC Disabled Enabled Disabled Disabled
Modem (Ring) Disabled Disabled Disabled N/A
S1
(Idle)
S3
(Suspend to
RAM)
S4
(Suspend to
DIsk)
(Shut Down)
S5
15
Power Management Function (ACPI support function)
Device Standby Mode
l Independent power management timer for hard disk drive devices
(0-15 minutes, time step=1 minute).
l Hard disk drive goes into Standby mode (for ATA standard interface).
l Disable V-sync to control the VESA DPMS monitor.
l Resume method: device activated (Keyboard for DOS, keyboard & mouse for Windows).
l Resume recovery time: 3-5 sec.
Global Standby Mode
l Global power management timer (2-120 minutes, time step=10 minute).
l Hard disk drive goes into Standby mode (for ATA standard interface).
l Disable H-sync and V-sync signals to control the VESA DPMS monitor.
l Resume method: Return to original state by pushing external switch button, modem ring in,
keyboard and mouse for APM mode.
l Resume recovery time: 7-10 sec.
Suspend Mode
l Independent power management timer (2-120 minutes, time step=10 minutes) or pushing
external
l switch button.
l CPU goes into SMM.
l CPU asserts STPCLK# and goes into the Stop Grant State.
l LED on the panel turns amber colour.
l Hard disk drive goes into SLEEP mode (for ATA standard interface).
l Disable H-sync and V-sync signals to control the VESA DPMS monitor.
l Ultra I/O and VGA chip go into power saving mode.
l Resume method: Return to original state by pushing external switch button, modem ring in,
keyboard and mouse for APM mode.
l Return to original state by pushing external switch button, modem ring in and USB keyboard for
ACPI mode.
ACPI
l ACPI specification 1.0b.
l S0, S1, S3 and S5 sleep state support.
l On board device power management support.
l On board device configuration support.
16
Chapter2
Using BIOS
About the Setup Utility
The computer uses the latest “American Megatrends Inc.” BIOS will support for Windows Plug and Play. The
CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides
you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that
saves this information when the power is turned off. When the system is turned back on, the system is configured
with the values you stored in CMOS.
The BIOS Setup Utility enables you to configure:
l Hard drives, diskette drives and peripherals
l Video display type and display options
l Password protection from unauthorized use
l Power Management features
The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure
that you understand the Setup Utility options.
This chapter provides explanations for Setup Utility options.
The Standard Configuration
A standard configuration has already been set in the Setup Utility. However, we recommend that you read this
chapter in case you need to make any changes in the future.
This Setup Utility should be used:
l when changing the system configuration
l when a configuration error is detected and you are prompted to make changes to the Setup
Utility
l when trying to resolve IRQ conflicts
l When making changes to the Power Management configuration
l when changing the password or making other changes to the Security Setup
Entering the Setup Utility
When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of
built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message
appears:
Press DEL to enter SETUP
17
BIOS Setup Utility(Main)
Pressing the DEL key accesses the BIOS Setup Utility:
The default BIOS setting for this motherboard applies for most conditions with optimum
performance. It is not suggested to change the default values in the BIOS setup and the
manufacture takes no responsibility to any damage caused by changing the BIOS settings.
Date and Time
The Date and Time items show the current date and time on the computer. If you are running a Windows OS,
these items are automatically updated whenever you make changes to the Windows Date and Time
Properties utility.
BIOS Navigation Keys
The BIOS navigation keys are listed below:
Key Function
••’‘ Move
Enter Select
+/- Change Opt
F7 Load User default Settings
F8 Save as User Default Settings
F9 Load Default Settings
F10 Save & Exit Setup
18
Updating the BIOS
You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New
BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install
new BIOS as follows:
1 If your motherboard has a BIOS protection jumper, change the setting to allow BIOS flashing.
2 If your motherboard has an item called Firmware Write Protect in Advanced BIOS features,
disable it. (Firmware Write Protect prevents BIOS from being overwritten.
3 Create a bootable system disk. (Refer to Windows online help for information on creating a
bootable system disk.)
4 Download the Flash Utility and new BIOS file from the manufacturer’s Website. Copy these files
to the system diskette you created in Step 3.
5 Turn off your computer and insert the system diskette in your computer’s diskette drive. (You
might need to run the Setup Utility and change the boot priority items on the Advanced BIOS
Features Setup page, to force your computer to boot from the floppy diskette drive first.)
6 At the A:\ prompt, type the Flash Utility program name and press <Enter>.
7 Type the filename of the new BIOS in the “File Name to Program” text box. Follow the onscreen
directions to update the motherboard BIOS.
8 When the installation is complete, remove the floppy diskette from the diskette drive and restart
your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the
newly installed BIOS from being overwritten.
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of
the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys
to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other
options lead to dialog boxes that prompt you for information.
Some options (marked with a triangle u ) lead to submenus that enable you to change the values for
the option. Use the cursor arrow keys to scroll through the items in the submenu.
In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a triangle u
19
BIOS Setup Utility(Advanced)
This option displays basic information about your system.
Miscellaneous
Scroll to this item and press <Enter> to view the following screen:
AHCI PORT1~4
This motherboard supports four SATA channels and each channel allows one SATA device to be installed.
Use these items to configure each device on the IDE channel.
Clock to All DIMM/PCIE (Disabled)
This item allows you to enable or disable the Clock to all DIMM/PCIE
20
Spread Spectrum (Enabled)
If you enable spread spertrum, it can significantly reduce the EMI (Electro-Magnetic interface) generated by
the system and voltage according to its temperature.
Bootup Num-lock (On)
This item determines if the Num Lock key is active or inactive at system start-up time.
USB Beep Message (Disabled)
This item disables/enables the beep during USB device enumeration.
Press <Esc> to return to the Advanecd BIOS Features page.
Advanced Chipset Configuration
This page sets up more advanced information about your system. Handle this page with caution. Any
changes can affect the operation of your computer.
Intel EIST(Enabled)
This item allows users to enable or disable the EIST(Enhanced Intel SpeedStep technology).
Intel Turbo Boost(Enabled)
This item enables or disables Intel Turbo Boost.
Intel AES-NT(Disabled)
This item allows users to enable or disable the Intel AES-NT.
Intel XD Bit
This item allows users to enable or disable the Intel XD Bit.Intel VT(Enabled)
Intel VT
This item allows you to enable or disable the Intel Virtualizationa Technology(Intel VT) function.
Video Memory Size(32KB)
This item applies to chipset/motherboards capable of the HyperMemory Support.
21
DVMT Mode(DVMT)
DVMT is Dynamic Video Memory Technology. This item helps you select video mode.
DVMT/Fixed Memory Size(256MB)
When set to Fixed Mode, the graphics driver will reserve a fixed portion of the system memory as graphics
memory. When set to DVMT Mode, the graphics chip will dynamically allocate system memory as graphics
memory, according to system anf graphics requirements.
Press <Esc> to return to the Advanecd BIOS Features page.
Integrated Peripherals
This page sets up some parameters for peripheral devices connected to the system.
Onboard SATA Controller (Enabled)
This item allows you to enable or disable the onboard SATA controller.
Onboard SATA Mode (AHCI)
Use this item to select the mode of the Serial ATA.
Onboard USB Controller (Enabled)
Use this item to enable or disable the onboard USB controller. We recommend users keep the default
value.
Legacy USB Support (Enabled)
Use this item to enable or disable support for legacy USB devices. Disabling it might cause the USB
devices not to work properly.
USB Storage Emulation (Auto)
If Auto, USB device equal or less than 2GB will be emulated as Floppy and remaining as hard drive.
Forced FDD option can be used to force a HDD formatted drive to boot as FDD(Ex. ZIP drive).
22
Onboard Graphics Controller (Enabled)
This item allows you to enable or disable the onboard controller.
Onboard Audio Controller (Enabled)
This item enables or disables the onboard audio controller.
Onboard LAN Controller (Enabled)
This option allows you to control the onboard LAN device.
Onboard LAN Option ROM (Disabled)
This item enables or disables the onboard LAN option ROM function
Press <Esc> to return to the Advanecd BIOS Features page.
PC Health Status
On motherboards support hardware monitoring, this item lets you monitor the parameters for critical
voltages, temperatures and fan speeds.
CPU Temperature (PECI Mode)
This item shows the CPU temperature.
System Temperature
This item shows the system temperature.
PCH Temperature
This item shows PCH temperature.
23
System Component Characteristics
These items display the monitoring of the overall inboard hardware health events, such as System & CPU
temperature, CPU voltage, CPU & system fan speed,...etc.
• CPU Fan Speed
• System Fan Speed
• CPU Core
• + 1.05V
• + 3.30V
• + 5.00 V
• + 12.0V
• 5VSB
• VBAT
Smart Fan (Enabled)
This item enables or disables the smart fan function.
Press <Esc> to return to the Advanecd BIOS Features page.
24
BIOS Setup Utility(Power)
This page sets up some parameters for system power management operation.
APCI Suspend Mode(S3(STR))
Use this item to define how your system suspends. In the default, S3(STR), the suspend mode is suspend to
RAM, i.e., the system shuts down with the exception of a refresh current to the system memory.
Deep Power off Mode (Enabled)
This item allows users to enable or disable the Deep Power off Mode.
Power on by RTC Alarm (Disabled)
This system can be turned off with a software commend. If you enable this item, the system can automatically
resume at a fixed time based on the system RTC (realtime clock). Use the items below this one to set the
date and time of the wake-up alarm. You must use an ATX power supply in order to use this feature.
Power on by PCIE Devices (Disabled)
This system can be turned off with a software commend. If you enable this item, the system can
automatically resume if there is an incoming call on the PCIE LAN card. You must use an ATX power supply
in order to use this feature. Use this item to do wake-up action if inserting the PCIE card.
Wake up by PS/2 KB/Mouse(Enabled)
This item enables or disables you to allow keyboard or mouse activity to awaken the system from power
saving mode.
Wake up by USB KB/Mouse(Enabled)
This item enables or disables you to allow keyboard or mouse activity to awaken the system from power
saving mode.
Restore On AC Power Loss (Last State)
This item defines how the system will act after AC power loss during system operation. When you set Off, it
will keep the system in Off state until the power button is pressed.
Loading...