Onkyo TX-SA806, TX-SR806 Instruction Manual

AV Receiver

TX-SR806

AV Amplifier

Contents

Introduction......................................2

Connections...................................17

First Time Setup ............................41

TX-SA806

Instruction Manual

Thank you for purchasing an Onkyo AV Receiver/ AV Amplifier. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver/ AV Amplifier. Please retain this manual for future reference.

Basic Operations ...........................56

Using the Listening Modes...........64

Advanced Setup.............................74

Zone 2 .............................................99

Controlling Other Components..105

Others ...........................................116

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important Safety Instructions

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons. The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS

OUVRIR

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand,

PORTABLE CART WARNING

tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to

S3125A

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A. When the power-supply cord or plug is dam-

aged,

B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or

water,

D. If the apparatus does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry

Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit.

17. Batteries

Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation,

such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides

and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a fluelike gap for warm air to escape.

Precautions

1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

For North American model Pressing the [ON/STANDBY] button to select Standby mode does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Preventing Hearing Loss Caution

Excessive sound pressure from earphones and headphones can cause hearing loss.

6. Batteries and Heat Exposure War nin g

Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like.

7. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit

for a long time, because they may leave marks on the case.

• This unit’s top and rear panels may get warm

after prolonged use. This is normal.

• If you do not use this unit for a long time, it may

not work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

AT TE NT IO N : POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Precautions—Continued

For British models

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral

Brown: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as fol-

lows: The wire which is coloured blue must be connected to

the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IMPORTANT

The plug is fitted with an appropriate fuse. If the fuse needs to be replaced, the replacement fuse must approved by ASTA or BSI to BS1362 and have the same ampere rating as that indicated on the plug. Check for the ASTA mark or the BSI mark on the body of the fuse. If the power cord’s plug is not suitable for your socket outlets, cut it off and fit a suitable plug. Fit a suitable fuse in the plug.

For European Models

Declaration of Conformity

We,

ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY

declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3.

GROEBENZELL, GERMANY

K. MIYAGI

ONKYO EUROPE ELECTRONICS GmbH

Supplied Accessories

Make sure you have the following accessories:

Remote controller & two batteries (AA/R6)

Speaker setup microphone

Indoor FM antenna (TX-SR806 only)

AM loop antenna (TX-SR806 only)

Power c ord

(Plug type varies from country to country.)

Left

Front

Right

Zone 2

Surround

SP-B

Zone 2

Front

Left

Front

Right

SP-B

Left

SP-B

Right

Surround

Front

Left

Front

Right

SP-B

Left

SP-B

Right

Speaker Cable

Left

Right

Surround

Left

Surround

Right

Surround

Left

Surround

Right

Center

Zone 2

Surround Back

Zone 2

Right

Zone 2

Left

Center

Zone 2

Right

Zone 2

Left

Surround Back

Right

Surround Back

Left

Center

Surround Back

Right

Surround Back

Left

Speaker cable labels

Power-plug adapter

Only supplied in certain countries. Use this adapter if your AC outlet does not match with the plug on the AV receiver/AV amplifier’s power cord (adapter varies from country to country).

*How to mount the AC plug:

* In catalogs and on packaging, the letter at the end of the product

name indicates the color. Specifications and operations are the same regardless of color.

Features

Amplifier

• 130 Watts/Channel (2ch Driven) @ 8 ohms (FTC)

• 180 Watts/Channel @ 6 ohms (IEC)

• 180 Watts/Channel @ 6 ohms (JEITA)

• WRAT-Wide Range Amplifier Technology

(5 Hz-100 kHz bandwidth)

• Linear Optimum Gain Volume Circuitry

• Push-Pull Amplifier Design with 3-Step Inverted Dar-

lington Circuitry

• H.C.P.S. (High Current Power Supply) Massive High

Power Transformer

Processing

• THX Ultra2 Plus*1 Certified

• HDMI Video Upscaling (to 1080p Compatible) with

Faroudja DCDi Cinema Enhancement

• HDMI ver.1.3a with Repeater System (Deep Color,

x.v.Color, Lip Sync, DTS DTS-HD High Resolusion Audio, Dolby TrueHD

-HD Master Audio,

Dolby Digital Plus, SA-CD and Multi-CH PCM)

• Component Video Upconversion

• Non-Scaling Configuration

• Direct Mode and Pure Audio Mode

• 192 kHz/24-bit D/A Converters

• Two TI (Aureus) 32-bit DSP Processing

Connections

• 5 HDMI*4 Inputs and 1 Output (ver. 1.3a)

• Onkyo for System Control

• 6 Digital Inputs (3 Optical / 3 Coaxial)

• 5 S-Video Inputs / 2 Outputs

• Component Video Switching (2 Inputs/1 Output)

• Banana Plug-Compatible Speaker Posts

• Powered Zone 2 and Zone 2 Pre Out

• IR Input/Output and 12 V Trigger

• RS232 Port for Interface Control

• Bi-Amp Connectable for FL/FR with SBL/SBR

Miscellaneous

• SIRIUS Ready*6 / XM Ready

round (North American models only)

• 40 SIRIUS/XM/AM/FM Presets (North American

models)

• 40 AM/FM Presets (European and Asian models)

Audyssey

•

MultEQ*8 Room Correction and Speaker

Calibration

• Audyssey Dynamic EQ

• Crossover Adjustment

(40/50/60/70/80/90/100/120/150/200 Hz)

• A/V Sync Control Function (up to 250 ms)

• Music Optimizer

for Compressed Music

• Newly Designed GUI for System Set-up

• Compatible with RI Dock for iPod

• Aluminum Front Panel

• Preprogrammed u-Compatible Remote with 2 Mac-

ros and Mode-Key LEDs

with XMHD Sur-

Loudness Correction

*1.

*2.

Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks of DTS, Inc. ©1996-2007 DTS, Inc. All Rights Reserved.

*3.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

*4.

HDMI, the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

*5. In Europe, using banana plugs to connect speakers to an audio

amplifier is prohibited.

*6.

©2005 SIRIUS Satellite Radio Inc. “SIRIUS”, SiriusConnect, the SIRIUS dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc. Available only in the contiguous United States (excluding Alaska and Hawaii) and Canada.

*7.

*8.

Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending. Audyssey MultEQ® and Dynamic

EQ are trademark of Audyssey Laboratories.

*9. Music Optimizer™ is a trademark of Onkyo Corporation.

THX Ultra2 Plus

Before any home theater component can be THX Ultra2 Plus certified, it must pass a rigorous series of quality and performance tests. Only then can a product feature the THX Ultra2 Plus logo, which is your guarantee that the Home Theater products you purchase will give you superb performance for many years to come. THX Ultra2 Plus requirements define hundreds of parameters, including power amplifier performance, and pre-amplifier performance and operation for both digital and analog domains. THX Ultra2 Plus receivers also feature proprietary THX technologies (e.g., THX Mode) which accurately translate movie soundtracks for home theater playback.

* “Xantech” is a registered trademark of Xantech Corporation. * “Niles” is a registered trademark of Niles Audio Corporation. * Apple and iPod are trademarks of Apple Inc., registered in the

U.S. and other countries.

* “x.v.Color” is a trademark of Sony Corporation.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Contents

Introduction

Important Safety Instructions .................................... 2

Precautions ............................................................... 3

Supplied Accessories................................................ 5

Features .................................................................... 6

Front & Rear Panels.................................................. 8

Front Panel............................................................ 8

Display................................................................. 10

Rear Panel .......................................................... 11

Remote Controller ................................................... 14

Installing the Batteries ......................................... 14

Aiming the Remote Controller ............................. 14

Controlling the AV Receiver/AV Amplifier ........... 15

About Home Theater............................................... 16

Enjoying Home Theater....................................... 16

Connections

Connecting the AV Receiver/AV Amplifier .............. 17

Connecting Your Speakers ................................. 17

Bi-amping the Front Speakers............................. 19

Connecting Antenna (TX-SR806 only) ................ 20

About AV Connections ........................................ 22

Connecting Both Audio & Video .......................... 23

Which Connections Should I Use?...................... 23

Connecting a TV or Projector .............................. 25

Connecting a DVD Player ................................... 26

Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Connecting a Satellite, Cable, Terrestrial

Set-top box, or Other Video Source.................. 30

Connecting a Game Console .............................. 31

Connecting a Camcorder or Other Device .......... 32

Connecting Components with HDMI ................... 33

Connecting a CD Player or Turntable ................. 35

Connecting a Cassette, CDR, MiniDisc,

or DAT Recorder............................................... 36

Connecting a Power Amplifier ............................. 37

Connecting a Tuner (TX-SA806 only) ................. 37

Connecting an RI Dock ....................................... 38

Connecting Onkyo u Components ................... 39

Connecting the Power Cord ................................ 39

Turning On the AV Receiver/AV Amplifier .............. 40

Turning On and Standby ..................................... 40

... 28

.... 29

First Time Setup

First Time Setup...................................................... 41

Monitor Setup...................................................... 41

Selecting the Language used for the onscreen

setup menus ..................................................... 42

Using the Onscreen Setup Menus ...................... 43

Video Input Setup................................................ 44

Digital Input Setup ............................................... 46

Speaker Settings ................................................. 47

TV Format Setup (not North American models)

AM Frequency Step Setup (on some models) .... 49

Changing the Input Display ................................. 50

Automatic Speaker Setup (Audyssey MultEQ®)

... 48

... 51

Basic Operations

Basic Operations..................................................... 56

Selecting the Input Source .................................. 56

Using the Multichannel DVD Input ...................... 57

Adjusting the Bass & Treble................................ 57

Displaying Source Information ............................ 57

Setting the Display Brightness ............................ 57

Muting the AV receiver/AV amplifier ................... 58

Using the Sleep Timer......................................... 58

Using Headphones.............................................. 58

Listening to the Radio (TX-SR806 only).................. 59

Using the Tuner ................................................... 59

Presetting AM/FM Stations.................................. 60

Using RDS (not North American model).............. 61

Recording ................................................................ 63

Using the Listening Modes

Using the Listening Modes ...................................... 64

Selecting Listening Modes................................... 64

Listening Modes Available for Each Source Format

About the Listening Modes .................................. 71

.... 65

Advanced Setup

Advanced Setup ...................................................... 74

Onscreen Setup Menus....................................... 74

Speaker Setup..................................................... 75

Audio Adjust Functions........................................ 83

Adjust Using the AUDIO Button........................... 85

Assigning Listening Modes to Input Sources....... 87

Source Setup....................................................... 88

Miscellaneous (Volume/OSD) Setup ................... 91

Hardware Setup................................................... 93

Lock Setup........................................................... 97

Automatic Audio Input Selection Setup ...............98

Digital Input Signal Formats ................................ 98

Zone 2

Zone 2 ..................................................................... 99

Connecting Zone 2 ..............................................99

Setting the Powered Zone 2 .............................. 100

Setting the Zone2 Out ....................................... 101

Using Zone 2 .....................................................102

Using the Remote Controller in Zone 2 and

Multiroom Control Kits..................................... 104

Controlling Other Components

Controlling Other Components.............................. 105

Preprogrammed Remote Control Codes ........... 105

Entering Remote Control Codes........................ 105

Remote Control Codes for Onkyo Components

Connected via u........................................... 106

Resetting REMOTE MODE Buttons .................. 106

Resetting the Remote Controller .......................106

Controlling a TV................................................. 107

Controlling a DVD Player, or DVD Recorder ..... 108

Controlling a VCR or PVR .................................109

Controlling a Satellite Receiver or Cable Receiver Controlling a CD Player, CD Recorder,

or MD Player ................................................... 111

Controlling an RI Dock....................................... 112

Controlling a Cassette Recorder ....................... 113

Controlling a Tuner (TX-SA806 only) ................ 113

Learning Commands ......................................... 114

Using Macros..................................................... 115

.... 110

Others

Specifications ........................................................ 116

Troubleshooting..................................................... 117

Video Resolution Chart ......................................... 122

* To reset the AV receiver/AV amplifier to its factory

defaults, turn it on and, while holding down the [VCR/DVR] button, press the [ON/STANDBY] button (see page 117).

Front & Rear Panels

5234 6 87

bk bm bnbo bp bqbr bsbtck cl cm cn co cp

bl bs

bl btck cm

Front Panel

TX-SR806 North American model

Front flap Push here to open the flap

cr csctcq

TX-SR806 other than North American model

TX-SA806

The actual front panel has various logos printed on it. They are not shown here for clarity.

Front & Rear Panels—Continued

The page numbers in parentheses show where you can find the main explanation for each item.

a ON/STANDBY button (40)

This button is used to set the AV receiver/AV amplifier to On or Standby.

b STANDBY indicator (40)

This indicator lights up when the AV receiver/AV amplifier is in Standby mode, and it flashes while a signal is being received from the remote controller.

c ZONE 2 indicator (102)

This indicator lights up when Zone 2 is selected.

d Input selector buttons (56)

These buttons are used to select from the following input sources: MULTI CH, DVD, VCR/DVR, CBL/SAT, GAME/TV, AUX, TAPE, TUNER, CD, PHONO. The [MULTI CH] button selects the DVD analog multichannel input.

e Remote control sensor (14)

This sensor receives control signals from the remote controller.

f Display

See “Display” on page 10.

g DISPLAY button (57)

This button is used to display various information about the currently selected input source.

h MASTER VOLUME control (56) and indicator

This control is used to adjust the volume of the AV receiver/AV amplifier to –∞ dB, –81.5 dB through +18.0 dB (relative display). The volume level can also be displayed as an absolute value. See “Volume Setup” on page 91.

i PURE AUDIO button and indicator (64)

Selects the Pure Audio listening mode. The indicator lights up when this mode is selected. Pressing this button again selects the previous listening mode.

j PHONES jack (58)

This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening.

k POWER switch (40)

North American models do not have this switch. This is the main power switch. When set to OFF, the AV receiver/AV amplifier is completely shutdown. It must be set to ON to set the AV receiver/AV amplifier to On or Standby.

l ZONE 2 and OFF buttons (102)

The [ZONE 2] button is used to select the input source for Zone 2. The [OFF] button is used to turn off the output of Zone 2.

m LEVEL button (103)

Used when adjusting the volume level of Zone 2.

n TONE button (57, 103)

Used to adjust the tone (bass and treble).

o HDMI OUT button (41)

Used to set the “Monitor Out” setting.

p MOVIE/TV button (64)

Selects the listening modes intended for use with movies and TV.

q MUSIC button (64)

Selects the listening modes intended for use with music.

r DIMMER or RT/PTY/TP button (57, 62)

This button is used to adjust the display brightness. On the European model, this is the [RT/PTY/TP] button, and it’s for RDS (Radio Data System). See “Using RDS (not North American model)” on page 61.

s MEMORY or Re-EQ button (60, 85)

This button is used when storing or deleting radio presets. On the TX-SA806, this button is used to turn the Re-EQ function on or off.

TUNING MODE or LATE NIGHT button (59, 85)

This button is used to select the Auto or Manual tuning mode. On the TX-SA806, this button is used to turn the Late Night function on or off.

u SETUP button

This button is used to access the onscreen setup menus that appear on the connected TV.

v Arrow, TUNING, PRESET and ENTER

buttons

When the AM or FM input source is selected, the TUNING [q]/[w] buttons are used to tune the tuner, and the PRESET [e]/[r] buttons are used to select radio presets (see page 60) (TX-SR806 only). When the onscreen setup menus are used, they work as arrow buttons and are used to select and set items. The [ENTER] button is also used with the onscreen setup menus.

w RETURN button

This button is used to return to the previously displayed onscreen setup menu.

x SETUP MIC jack (51)

The included speaker setup microphone is connected here for automatic speaker setup.

y AUX INPUT

This input can be used to connect a camcorder, game console, and so on. There are jacks for S-Video, composite video, analog audio, and optical digital audio.

z Up [r] and Down [e] buttons (57, 103)

Used to adjust the tone, and the volume and balance of Zone 2.

cr DIGITAL INPUT button (98)

Selects the options for automatic audio input selection setup.

cs GAME button (64)

Selects the listening modes intended for use with video games.

ct THX button (64)

Selects the THX listening modes.

Front & Rear Panels—Continued

Display

23 4

For detailed information, see the pages in parentheses.

a Speaker/channel indicators (75)

Indicate the speaker configuration and channels used by the current input source.

: A box is displayed for each speaker that’s set in the Speaker Configuration. No box appears for speakers that are set to “No” or “None”. The following abbreviations indicate which audio channels are included in the current input signal.

FL: Front left C: Center FR: Front right SL: Surround left LFE: Subwoofer (Low Frequency Effects) SR: Surround right SBL: Surround back left SB: Surround back SBR: Surround back right

b ZONE 2 indicator (102)

Lights up when Powered Zone 2 is being used.

c Listening mode and format indicators (64)

Show the selected listening mode and audio input signal format.

d Tuning indicators (TX-SR806 only) (59)

RDS (not North American model) (61):

Lights up when tuned to a radio station that supports RDS (Radio Data System).

AUTO (59):

Lights up when Auto Tuning mode is selected for AM or FM radio. Goes off when Manual Tuning mode is selected.

TUNED (59):

Lights up when tuned to a radio station.

FM STEREO (59):

Lights up when tuned to a stereo FM station.

e SLEEP indicator (58)

Lights up when the Sleep function has been set.

f Audyssey indicator (51, 80)

Flashes during automatic speaker setup. Lights up when the “Equalizer Settings” is set to “Audyssey”.

g Headphone indicator (58)

Lights up when a pair of headphones are plugged into the PHONES jack.

h Message area

Displays various information.

i Audio input indicators

Indicate the type of audio input that’s selected as the audio source: HDMI, ANALOG, or DIGITAL.

j Volume level (56)

Displays the volume level.

k MUTING indicator (58)

Flashes while the AV receiver/AV amplifier is muted.

Front & Rear Panels—Continued

12 9 bnbkblbm874

bs bt

12 bn874

bs bt

9b k

12 bnbk74

cpcn

br bt

Rear Panel

TX-SR806 North American model

TX-SR806 other than North American model

TX-SA806

Front & Rear Panels—Continued

a u REMOTE CONTROL

This u (Remote Interactive) jack can be connected to an u jack on another Onkyo AV component. The AV receiver/AV amplifier’s remote controller can then be used to control that component. To use u, you must make an analog audio connection (RCA) between the AV receiver/AV amplifier and the other AV component, even if they are connected digitally.

b PHONO IN

This audio input is for connecting a turntable.

c COMPONENT VIDEO IN 1 and 2

These RCA component video inputs are for connecting components with a component video output, such as a DVD player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Component Video Setup” on page 45.

COMPONENT VIDEO MONITOR OUT

This RCA component video output is for connecting a TV or projector with a component video input.

d HDMI IN 1–5 and OUT

HDMI (High Definition Multimedia Interface) connections carry digital audio and digital video. The HDMI inputs are for connecting components with an HDMI output, such as a DVD player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “HDMI Input Setup” on page 44. The HDMI output is for connecting a TV or projector with an HDMI input.

e MONITOR OUT

The S-Video or composite video jack should be connected to a video input on your TV or projector.

f IR IN/OUT

A commercially available IR receiver can be connected to the IR IN jack, allowing you to control the AV receiver/AV amplifier while you’re in Zone 2, or control it when it’s out of sight, for example, installed in a cabinet. A commercially available IR emitter can be connected to the IR OUT jack to pass IR (infrared) remote control signals through to other components.

g 12V TRIGGER OUT ZONE 2

This output can be connected to the 12-volt trigger input on a component in Zone 2. When Zone 2 is turned on on the AV receiver/AV amplifier, a 12volt trigger signal is output.

h FM ANTENNA (TX-SR806 only)

This jack is for connecting an FM antenna.

i AM ANTENNA (TX-SR806 only)

These push terminals are for connecting an AM antenna.

j RS232

This is the RS232 port.

k XM antenna (North American models only)

This jack is for connecting an XM Mini-Tuner and Home Dock, sold separately (see the separate XM instructions).

l SIRIUS antenna (North American models

only)

This jack is for connecting a SIRIUS Satellite Radio antenna, sold separately (see the separate SIRIUS instructions).

m AC INLET

The supplied power cord is connected here. The other end of the power cord should be connected to a suitable wall outlet.

n DIGITAL COAXIAL IN 1, 2, and 3

These coaxial digital audio inputs are for connecting components with coaxial digital audio outputs, such as CD and DVD players. They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Digital Input Setup” on page 46.

o DIGITAL OPTICAL IN 1 and 2

These optical digital audio inputs are for connecting components with optical digital audio outputs, such as CD and DVD players. They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Digital Input Setup” on page 46.

p GND screw

This screw is for connecting a turntable’s ground wire.

q TUNER IN (TX-SA806 only)

This analog audio input is for connecting a tuner’s analog audio output.

r CD IN

This analog audio input is for connecting a CD player’s analog audio output.

s TAPE IN/OUT

This analog audio input and output are for connecting a recorder with an analog audio input and output (cassette, Mini Disc, etc.).

t GAME/TV IN

Here you can connect a game console, TV, etc. Input jacks include S-Video, composite video, and analog audio.

u CBL/SAT IN

Here you can connect a cable/satellite receiver, settop box, etc. Input jacks include S-Video, composite video, and analog audio.

Front & Rear Panels—Continued

v VCR/DVR IN/OUT

Here you can connect a VCR or DVR (digital video recorder). Input and output jacks include S-Video, composite video, and analog audio.

w DVD V, S, FRONT L/R

Here you can connect a DVD player. Input jacks include S-Video, composite video, and analog audio. You can connect a DVD player’s 2-channel analog audio output.

DVD FRONT L/R, CENTER, SUBWOOFER, SURR L/R, and SURR BACK L/R

This analog multichannel input is for connecting a component with a 5.1/7.1-channel analog audio output, such as a DVD player, DVD-Audio or SACDcapable player, or an MPEG decoder.

x PRE OUT: FRONT L/R, CENTER,

SUBWOOFER, SURR L/R, and SURR BACK L/R

This 5.1/7.1 multichannel analog audio output can be connected to the analog audio input on a multichannel power amplifier for when you want to use the AV receiver/AV amplifier solely as a preamplifier. The SUBWOOFER jack is for connecting a powered subwoofer.

y PRE OUT: ZONE 2 L/R

This analog audio output can be connected to a line input on an integrated amplifier in Zone 2. See “Connecting Zone 2” on page 99.

z FRONT L/R, CENTER, SURR L/R, and SURR

BACK L/R speakers

These terminal posts are for connecting the front L/R, center, surround L/R, and surround back L/R speakers. The FRONT L/R and SURR BACK L/R terminal posts can be used with front speakers and surround back speakers respectively, or used to bi-amp the front speakers. See “Bi-amping the Front Speakers” on page 19”.

cr ZONE 2 L/R speakers

These terminals are for connecting speakers in Zone 2. See “Connecting Zone 2” on page 99.

See pages 16-39 for connection information.

Remote Controller

Installing the Batteries

To open the battery compartment, press

the small lever and remove the cover.

Insert the two supplied batteries (AA/R6)

in accordance with the polarity diagram inside the battery compartment.

Replace the cover and push it shut.

Notes:

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion.

Aiming the Remote Controller

To use the remote controller, point it at the AV receiver/AV amplifier’s remote control sensor, as shown below.

Remote control sensor

STANDBY indicator

Notes:

• The remote controller may not work reliably if the AV receiver/AV amplifier is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing.

• If another remote controller of the same type is used in the same room, or the AV receiver/AV amplifier is installed close to equipment that uses infrared rays, the remote controller may not work reliably.

• Don’t put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries.

• The remote controller may not work reliably if the AV receiver/AV amplifier is installed in a rack behind colored glass doors. Keep this in mind when installing.

• The remote controller will not work if there’s an obstacle between it and the AV receiver/AV amplifier’s remote control sensor.

• When the remote control codes have been registered and you want to operate another component (page 105), or when you want to operate an Onkyo component without u connection, point the remote controller at the other component to use it.

• When you want to operate an Onkyo component with u connection or an -compatible compo- nent connected via HDMI (page 107), point the remote controller at the AV receiver/AV amplifier’s remote control sensor.

AV receiver/AV amplifier

Approx. 16 ft. (5 m)

Remote Controller—Continued

Controlling the AV Receiver/ AV Amplifier

To control the AV receiver/AV amplifier, press the [RECEIVER] button to select Receiver mode. You can also use the remote controller to control your DVD player, CD player, and other components. See page 105 for more details.

3 4

bk bl

5 6

bm bn

For detailed information, see the pages in parentheses.

a ON/STANDBY button (40)

Sets the AV receiver/AV amplifier to On or Standby.

b REMOTE MODE/INPUT SELECTOR buttons

(56, 107–113)

Selects the remote controller modes and the input sources.

c MULTI CH button (57)

Selects the multichannel DVD input.

d MACRO buttons (115)

Used with the Macro function.

e Arrow [q]/[w]/[e]/[r] and ENTER buttons

Used to select and adjust settings.

f SETUP button

Used to change settings.

g LISTENING MODE buttons (64)

Used to select the listening modes.

h DIMMER button (57)

Adjusts the display brightness.

i DISPLAY button (57)

Displays information about the current input source.

j MUTING button (58)

Mutes or unmutes the AV receiver/AV amplifier.

k VOL [q]/[w] button (56)

Adjusts the volume of the AV receiver/AV amplifier regardless of the currently selected remote controller mode.

l RETURN button

Returns to the previous display when changing settings.

m AUDIO button (85)

Used to change audio settings. When the “Audio TV Out” setting is set to “On” (page 95), this button is disabled.

n SLEEP button (58)

Used with the Sleep function.

* SP A/B is not used in this AV receiver/AV amplifier.

■ Controlling the tuner (TX-SR806 only)

To control the AV receiver’s tuner, press the [TUNER] (or [RECEIVER]) button. You can select AM or FM by pressing the [TUNER] button repeatedly.

1 Arrow [q]/[w] buttons

Used to tune into radio stations.

2 Number buttons (59)

Used to select radio stations directly.

3 D.TUN button (59)

Selects the Direct tuning mode.

4 DISPLAY button

Displays information about the band, frequency, preset number, and so on.

5 CH +/– button (60)

Used to select radio presets.

Note:

An Onkyo cassette recorder connected via u can also be controlled in Receiver mode (see page 113).

About Home Theater

Enjoying Home Theater

Thanks to the AV receiver/AV amplifier’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes. You can also enjoy THX Surround EX (THX-certified THX speaker system recommended).

Front left and right speakers

These output the overall sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equidistant from the TV. Angle them inward so as to create a triangle, with the listener at the apex.

Surround back left and right speakers

These speakers are necessary to enjoy Dolby Digital EX, DTS-ES Matrix, DTS-ES Discrete, THX Sur-

Center speaker

This speaker enhances the front left and right speakers, making sound movements distinct and providing a full sound image. In movies it’s used mainly for dialog. Position it close to your TV facing forward at about ear level, or at the same height as the front left and right speakers.

Corner

round EX, etc. They enhance the realism of surround sound and improve sound localization behind the listener. Position them behind the listener about 2–3 feet (60– 100 cm) above ear level.

Subwoofer

The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) channel. The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listening position. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at one-third the width of the wall, as shown. Tip: To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results.

1/3 wall length

Surround left and right speakers

These speakers are used for precise sound positioning and to add realistic ambience. Position them at the sides of the listener, or slightly behind, about 2–3 feet (60–100 cm) above ear level. Ideally they should be equidistant from the listener.

Connecting the AV Receiver/AV Amplifier

Connecting Your Speakers

Speaker Configuration

For 7.1-channel surround-sound playback, you need seven speakers and a powered subwoofer.

The following table indicates the channels you should use depending on the number of speakers that you have.

Number of speakers: 2 3 4 5 6 7

Front left ✓✓✓✓✓✓

Front right ✓✓✓✓✓✓

Center ✓✓✓✓

Surround left ✓✓✓✓

Surround right ✓✓✓✓

Surround back* ✓

Surround back left ✓

Surround back right ✓

* If you’re using only one surround back speaker, connect it to the

SURR BACK L terminals.

No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass.

To get the best from your surround sound system, you need to set the speaker settings. You can do this automatically (see page 51) or manually (see page 75).

Using Dipole Speakers

You can use dipole speakers for the surround left and right and surround back left and right speakers. Dipole speakers output the same sound in two directions.

Dipole speakers typically have an arrow printed on them to indicate how they should be positioned. The surround left and right their arrows point toward the TV/screen, while the surround back left and right dipole speakers should be positioned so that their arrows point toward each other, as shown.

dipole

speakers should be positioned so that

Dipole speakers

TV/screen

Normal speakers

TV/screen

Connecting a Powered Subwoofer

Using a suitable cable, connect the AV receiver/AV amplifier’s PRE OUT: SUBWOOFER to an input on your powered subwoofer, as shown. If your subwoofer is unpowered and you’re using an external amplifier, connect the PRE OUT: SUBWOOFER to an input on the amp.

Powered

subwoofer

LINE INPUT

Attaching the Speaker Labels

The AV receiver/AV amplifier’s positive (+) speaker terminals are all red (the negative (–) speaker terminals are all black).

Speaker Color

Front left, Zone 2 left White

Front right, Zone 2 right Red

Center Green

Surround left Blue

Surround right Gray

Surround back left Brown

Surround back right Tan

The supplied speaker cable labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the above table. Then all you need to do is to match the color of each label to the corresponding speaker terminal.

7 8

1. Subwoofer

2. Front left speaker

3. Center speaker

4. Front right speaker

5. Surround left speaker

6. Surround right speaker

7. Surround back left speaker

8. Surround back right speaker

For North American model

• If you are using banana plugs, tighten the speaker ter-

minal before inserting the banana plug.

• Do not insert the speaker code directly into the center hole of the speaker terminal.

Connecting the AV Receiver/AV Amplifier—Continued

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, be sure to set the minimum speaker impedance to “4ohms” (see page 47). If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+) terminals, and negative (–) terminals only to negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided.

Connecting the Speaker Cables

• If you use 4 or 5 speakers, connect each of the two surround speakers to the SURR L/R terminals. Do not connect them to the SURR BACK L/R terminals.

• Be careful not to short the positive and negative wires. Doing so may damage the AV receiver/AV amplifier.

• Make sure the metal core of the wire does not have contact with the AV receiver/AV amplifier’s rear panel. Doing so may damage the AV receiver/AV amplifier.

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver/AV amplifier.

• Don’t connect one speaker to several terminals.

Strip about 5/8" (15 mm)

of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

Unscrew the terminal.

The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one surround back speaker, connect it to the SURR BACK L terminals.

5/8"(15 mm)

Fully insert the bare

wires.

Screw the terminal tight.

Center speaker Front left speakerFront right speaker

Surround back

right speaker

Surround right

speaker

Surround left

speaker

Surround back

left speaker

Connecting the AV Receiver/AV Amplifier—Continued

Bi-amping the Front Speakers

The FRONT L/R and SURR BACK L/R terminal posts can be used with front speakers and surround back speakers respectively, or bi-amped to provide separate tweeter and woofer feeds for a pair of front speakers that support bi-amping, providing improved bass and treble performance.

• When bi-amping is used, the AV receiver/AV amplifier is able to drive up to 5.1 speakers in the main room.

• For bi-amping, the FRONT L/R terminal posts connect to the front speakers’ woofer terminals. And the SURR BACK L/R terminal posts connect to the front speakers’ tweeter terminals.

• Once you’ve completed the bi-amping connections shown below and turned on the AV receiver/AV amplifier, you must set the “Speakers Type” setting to “Bi-Amp” to enable biamping (see page 47).

Important:

• When making the bi-amping connections, be sure to remove the jumper bars that link the speakers’ tweeter (high) and woofer (low) terminals.

• Bi-amping can only be used with speakers that support bi-amping. Refer to your speaker manual.

Bi-amping Speaker Hookup

Connect the AV receiver/AV amplifier’s FRONT

R positive (+) terminal to the right speaker’s positive (+) Woofer (low) terminal. And connect the AV receiver/AV amplifier’s FRONT R negative (–) terminal to the right speaker’s negative (–) Woofer (low) terminal.

Connect the AV receiver/AV amplifier’s SURR

BACK R positive (+) terminal to the right speaker’s positive (+) Tweeter (high) terminal. And connect the AV receiver/AV amplifier’s SURR BACK R negative (–) terminal to the right speaker’s negative (–) Tweeter (high) terminal.

Connect the AV receiver/AV amplifier’s FRONT

L positive (+) terminal to the left speaker’s positive (+) Woofer (low) terminal. And connect the AV receiver/AV amplifier’s FRONT L negative (–) terminal to the left speaker’s negative (–) Woofer (low) terminal.

Connect the AV receiver/AV amplifier’s SURR

BACK L positive (+) terminal to the left speaker’s positive (+) Tweeter (high) terminal. And connect the AV receiver/AV amplifier’s SURR BACK L negative (–) terminal to the left speaker’s negative (–) Tweeter (high) terminal.

Tweeter (high) Tweeter (high)

Woofer (low)

Right speaker Left speaker

Woofer (low)

Connecting the AV Receiver/AV Amplifier—Continued

Connecting Antenna (TX-SR806 only)

This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.

The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

FM ANTENNA jack

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

Attach the FM antenna, as shown.

■ North American models

AM ANTENNA push terminals

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead (see page 21).

Connecting the AM Loop Antenna

The supplied indoor AM loop antenna is for indoor use only.

Assemble the AM loop antenna, inserting

the tabs into the base, as shown.

Connect both wires of the AM loop

antenna to the AM antenna push terminals, as shown.

(The antenna’s wires are not polarity sensitive, so they can be connected either way around.)

Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.

Insert the plug fully into the jack.

■ Other models

Insert the plug fully into the jack.

Once your AV receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.

Use thumbtacks or something similar to

fix the FM antenna into position.

Thumbtacks, etc.

Push Insert wire Release

Once your AV receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception. Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna (see page 21).

Caution:

Be careful that you don’t injure yourself when using thumbtacks.

Connecting the AV Receiver/AV Amplifier—Continued

Connecting an Outdoor FM Antenna

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

Notes:

• Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft.

• For best results, install the outdoor FM antenna well away from tall buildings, preferably with a clear line of sight to your local FM transmitter.

• Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc.

• For safety reasons, outdoor antenna should be situated well away from power lines and other high-voltage equipment.

• Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

Connecting an Outdoor AM Antenna

If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.

Outdoor antenna

Insulated antenna cable

AM loop antenna

Outdoor AM antennas work best when installed outside horizontally, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected.

Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

■ Using a TV/FM Antenna Splitter

It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown.

TV/FM antenna splitter

To AV receiver To TV (or VCR)

Connecting the AV Receiver/AV Amplifier—Continued

About AV Connections

• Before making any AV connections, read the manuals supplied with your other AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

Optical Digital Jacks

The AV receiver/AV amplifier’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.

Caution:

To prevent shutter damage, hold the optical plug straight when inserting and removing.

AV Cables & Jacks

Video

Cable Jack Description

HDMI

Component video cable

B/CB

PR/CR

B/CB

PR/CR

AV Connection Color Coding

RCA-type AV connections are usually color-coded: red, white, and yellow. Use red plugs to connect right-channel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.

Left (white)

Right (red) Right (red)

(Yellow)

•

Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

HDMI

HDMI connections can carry uncompressed standard- or high-definition digital video and audio and offer the best picture and sound quality.

Component video separates the luminance (Y) and color difference signals (PR, PB), providing the best picture quality (some TV manufacturers label their component video sockets slightly differently).

Analog audio

Composite video

Left (white)

(Yellow)

Right!

Wrong!

S-Video cable

Composite video cable

Audio

Optical digital audio cable

Coaxial digital audio cable

Analog audio cable (RCA)

Multichannel analog audio cable (RCA)

Cable Jack Description

Note:

The AV receiver/AV amplifier does not support SCART plugs.

S-Video separates the luminance and color signals and provides better picture quality than composite video.

Composite video is commonly used on TVs, VCRs, and other video equipment.

Offers the best sound quality and allows you to enjoy surround sound (e.g., Dolby Digital, DTS). The audio quality is the same as for coaxial.

Offers the best sound quality and allows you to enjoy surround sound (e.g., Dolby Digital, DTS). The audio quality is the same as for optical.

This cable carries analog audio. It’s the most common connection format for analog audio, and can be found on virtually all AV components.

This cable carries multichannel analog audio and it’s typically used to connect DVD players with a

7.1-channel analog audio output. Several standard analog audio cables can be used instead of a multichannel cable.

Connecting the AV Receiver/AV Amplifier—Continued

Connecting Both Audio & Video

By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver/AV amplifier, you can select both the audio and video simultaneously simply by selecting the appropriate input source on the AV receiver/AV amplifier.

: Signal Flow

Video

Audio

DVD player, etc.

Speakers

(see page 18 for connection information)

Video

Audio

TV, projector,

etc.

Which Connections Should I Use?

The AV receiver/AV amplifier supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your other components. Use the following sections as a guide.

For video components, you must make two connections—one for audio, one for video.

Video Connection Formats

Video equipment can be connected to the AV receiver/AV amplifier by using any one of the following video connection formats: composite video, S-Video, component video, or HDMI, the latter offering the best picture quality.

The AV receiver/AV amplifier can upconvert and downconvert between video formats, depending on the “Monitor Out” setting, which generally determines whether video signals are upconverted for the component video output or the HDMI output.

For optimal video performance, THX recommends that video signals pass through the system without upconversion (e.g., component video input through to component video output). It is also recommended that you set the “Immediate Display” preference to “Off” (see page 92), the “Picture Adjust” setting to the default (see page 90), and the “Output Resolution” setting to “Through” (see page 94).

■ “Monitor Out” Setting Set to “HDMI”

With the “Monitor Out” setting set to “HDMI” (see page 41), video input signals flow through the AV receiver/AV amplifier as shown, with composite video, S-Video, and component video sources all being upconverted for the HDMI output. Use this setting if you connect the AV

receiver/AV amplifier’s HDMI OUT to your TV.

The composite video, S-Video, and component video outputs pass through their respective input signals as they are.

DVD player, etc.

AV receiver/

AV amplifier

TV, projector, etc.

Video Signal Flow Chart

Composite

S-Video

MONITOR OUT

S-Video

Component

HDMI

Connecting the AV Receiver/AV Amplifier—Continued

■ “Monitor Out” Setting Set to “Analog”

With the “Monitor Out” setting set to “Analog” (see page 41), video input signals flow through the AV receiver/AV amplifier as shown, with composite video and S-Video sources being upconverted for the component video output.

Use this setting if you connect the AV receiver/AV amplifier’s COMPONENT VIDEO MONITOR OUT to your TV.

Composite video is upconverted to S-Video and S-Video is downconverted to composite video. Note that these conversions only apply to the MONITOR OUT V and S outputs, not the VCR/DVR OUT V and S outputs.

The composite video, S-Video, and component video outputs pass through their respective input signals as they are.

This signal flow also applies when the “Output Resolution” setting is set to “Through” (see page 94).

Video Signal Flow and the Resolution Setting

When the “Monitor Out” setting is set to “Analog” (see page 41), if the “Output Resolution” setting is set to anything other than “Through” (see page 94), the video signal flow will be as shown here, with composite video and S-Video sources being upconverted for the component video output.

The composite video, S-Video, and component video outputs pass through their respective analog input signals as they are. HDMI input signals are not output.

DVD player, etc.

AV receiver/ AV amplifier

TV, projector, etc.

DVD player, etc.

AV receiver/ AV amplifier

Video Signal Flow Chart

Composite

Video Signal Flow Chart

Composite

S-Video

MONITOR OUT

S-Video

MONITOR OUT

S-Video

Component

HDMI

TV, projector, etc.

Audio Connection Formats

Audio equipment can be connected to the AV

DVD player, etc.

receiver/AV amplifier by using any of the following audio connection formats: analog, optical, coaxial, analog multichannel, or HDMI. When choosing a connection format, bear in mind that the AV receiver/AV amplifier does not convert digital input signals for analog line outputs and vice versa. For example, audio signals

AV receiver/ AV amplifier

connected to an optical or coaxial digital input are not output by the analog TAPE OUT.

MD recorder, etc.

If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: HDMI, digital, analog (including multichannel). You can specify which audio inputs the AV receiver/AV amplifier checks for the presence of a signal in the “Automatic Audio Input Selection Setup” on page 98.

Audio Signal Flow Chart

Multichannel

*1 Depends on the “Audio TV Out” setting

(see page 95).

*2 Only the front L/R channels are output.

(There will be no down mix.)

Optical

OUT

HDMICoaxial Analog

HDMI Analog

Connecting the AV Receiver/AV Amplifier—Continued

Connecting a TV or Projector

See “Connecting Components with HDMI” on page 33 for HDMI connection information.

Step 1: Video Connection

Choose a video connection that matches your TV ( , , or ), and then make the connection.

Step 2: Audio Connection

Choose an audio connection that matches your TV ( , , or ), and then make the connection.

A B C

a b c

• With connection , you can listen to and record audio from your TV and listen in Zone 2.

• To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2 as well, use and , or and .)

a c

b c a b

Connection AV receiver/AV amplifier Signal flow TV

COMPONENT VIDEO MONITOR OUT ⇒ Component video input

MONITOR OUT S ⇒ S-Video input

MONITOR OUT V ⇒ Composite video input

GAME/TV IN L/R ⇐ Analog audio L/R output

DIGITAL COAXIAL IN 2 (VCR/DVR) ⇐ Digital coaxial output

DIGITAL OPTICAL IN 1 (GAME/TV) ⇐ Digital optical output

BCB

OPTICAL

OUT

Connect one or the other Connection must be assigned (see page 46)

Hint!

If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiver to the AV receiver/AV amplifier and use its tuner to listen to TV programs through the AV receiver/AV

YCOAXIAL

COMPONENT VIDEO IN

amplifier (see pages 28 and 30).

PR S VIDEO

AUDIO

OUT

TV, projector,

etc.

VIDEO

Connecting the AV Receiver/AV Amplifier—Continued

Connecting a DVD Player

See “Connecting Components with HDMI” on page 33 for HDMI connection information.

Step 1: Video Connection

Choose a video connection that matches your DVD player ( , , or ), and then make the connection. If you use connection , you must connect the AV receiver/AV amplifier to your TV via the same type of connec-

tion.

Step 2: Audio Connection

Choose an audio connection that matches your DVD player ( , , or ), and then make the connection.

A B C

a b c

• With connection , you can listen to and record audio from a DVD and listen in Zone 2.

• To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2 as well, use and , or and .)

a c

b c a b

• If your DVD player has main left and right outputs and multichannel left and right outputs, be sure to use the main left and right outputs for connection .

Connection AV receiver/AV amplifier Signal flow DVD player

COMPONENT VIDEO IN 1 (DVD) ⇐ Component video output

DVD S ⇐ S-Video output

DVD V ⇐ Composite video output

DVD FRONT L/R ⇐ Analog audio L/R output

DIGITAL COAXIAL IN 1 (DVD) ⇐ Digital coaxial output

DIGITAL OPTICAL IN 1 (GAME/TV) ⇐ Digital optical output

OUT

Connect one or the other Connection must be assigned (see page 46)

OPTICAL

OUT

YCOAXIAL

COMPONENT VIDEO OUT

R S VIDEO

AUDI O

OUT

VIDEO

OUT

DVD player

To connect a DVD player or DVD-Audio/SACD-capable player with a multichannel analog audio output, see page 27.

Connecting the AV Receiver/AV Amplifier—Continued

Hooking Up the Multichannel DVD Input

If your DVD player supports multichannel audio formats such as DVD-Audio or SACD, and it has a multichannel analog audio output, you can connect it to the AV receiver/AV amplifier’s multichannel DVD input.

Use a multichannel analog audio cable, or several normal audio cables, to connect the AV receiver/AV amplifier’s DVD FRONT L/R, CENTER, SURR L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.1-channel analog audio output on your DVD player. If your DVD player has a 5.1-channel analog audio output, don’t connect anything to the AV receiver/AV amplifier’s SURR BACK L/R jacks.

To select the multichannel input, see “Using the Multichannel DVD Input” on page 57. To adjust the subwoofer sensitivity for the multichannel input, see “Hardware Setup” on page 93.

7.1 ch

5.1 ch

FRONT CENTER

SUBWOOFER

SURR

DVD

SURR BACK

FRONT

CENTER SUB

WOOFER

SURROUND

SURR BACK

DVD playe r

Note:

When a signal from multichannel DVD input is output from HDMI OUT or analog audio output, only the front L/R channels will be output. There will be no down mix.

Connecting the AV Receiver/AV Amplifier—Continued

Connecting a VCR or DVD Recorder for Playback

Hint!

With this hookup, you can use your VCR’s tuner to listen to your favorite TV programs via the AV receiver/AV amplifier, useful if your TV has no audio outputs.

Step 1: Video Connection

Choose a video connection that matches your VCR or DVD recorder ( , , or If you use connection , you must connect the AV receiver/AV amplifier to your TV via the same type of connec-

A B C

), and then make the connection.

tion.

Step 2: Audio Connection

Choose an audio connection that matches your VCR or DVD recorder ( , , or ), and then make the connection.

• With connection , you can listen to the VCR or DVD recorder even in Zone 2.

• To enjoy Dolby Digital and DTS, use connection or . (To listen in Zone 2 as well, use and , or and

Connection AV receiver/AV amplifier Signal flow VCR or DVD recorder

b c a b a

COMPONENT VIDEO IN 2 (CBL/SAT) ⇐ Component video output

VCR/DVR IN S ⇐ S-Video output

VCR/DVR IN V ⇐ Composite video output

VCR/DVR IN L/R ⇐ Analog audio L/R output

DIGITAL COAXIAL IN 2 (VCR/DVR) ⇐ Digital coaxial output

DIGITAL OPTICAL IN 1 (GAME/TV) ⇐ Digital optical output

a b c

Connection

must be

assigned

(see page 45)

Connect one or the other Connection must be assigned (see page 46)

OUT

OPTICAL

OUT

YCOAXIAL

R S VIDEO

COMPONENT VIDEO OUT

DVD record er

AUDI O

OUT

VCR,

OUT

VIDEO

OUT

Connecting the AV Receiver/AV Amplifier—Continued

Connecting a VCR or DVD Recorder for Recording

Step 1: Video Connection

Choose a video connection that matches your VCR or DVD recorder ( or ), and then make the connection. The video source to be recorded must be connected to the AV receiver/AV amplifier via the same type of connection.

Step 2: Audio Connection

Make the audio connection .

Connection AV receiver/AV amplifier Signal flow VCR or DVD recorder

VCR/DVR OUT S

VCR/DVR OUT V

VCR/DVR OUT L/R

A B

⇒

S-Video input

Composite video input

Analog audio L/R input

AUDIO

Notes:

• The AV receiver/AV amplifier must be turned on for recording. Recording is not possible while it’s in Standby mode.

• If you want to record directly from your TV or playback VCR to the recording VCR without going through the AV receiver/AV amplifier, connect the TV/VCR’s audio and video outputs directly to the recording VCR’s audio and video inputs. See the manuals supplied with your TV and VCR for details.

• Video signals connected to composite video inputs can only be recorded via composite video outputs. If your TV/VCR is connected to a composite video input, the recording VCR must be connected to a composite video output. Similarly, video signals connected to S-Video inputs can only be recorded via S-Video outputs. If your TV/VCR is connected to an S-Video input, the recording VCR must be connected to an S-Video output.

S VIDEO

VCR,

DVD recorder

VIDEO

Connecting the AV Receiver/AV Amplifier—Continued

Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source

Hint!

With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV receiver/AV amplifier, useful if your TV has no audio outputs.

Step 1: Video Connection

Choose a video connection that matches the video source ( , , or ), and then make the connection. If you use connection , you must connect the AV receiver/AV amplifier to your TV via the same type of connec-

A B C

tion.

Step 2: Audio Connection

Choose an audio connection that matches the video source ( , , or ), and then make the connection.

• With connection , you can listen to and record audio from the video source and listen in Zone 2.

• To enjoy Dolby Digital and DTS, use connection or . (To listen in Zone 2 as well, use and , or and .)

Connection AV receiver/AV amplifier Signal flow Video source

COMPONENT VIDEO IN 2 (CBL/SAT) ⇐ Component video output

CBL/SAT IN S ⇐ S-Video output

CBL/SAT IN V ⇐ Composite video output

CBL/SAT IN L/R ⇐ Analog audio L/R output

DIGITAL COAXIAL IN 3 (CBL/SAT) ⇐ Digital coaxial output

DIGITAL OPTICAL IN 2 (CD) ⇐ Digital optical output

a b c

b c a b a

OPTICAL

OUT

Connect one or the other Connection must be assigned (see page 46)

OUT

YCOAXIAL

R S VIDEO

COMPONENT VIDEO OUT

BCB

AUDI O

OUT

Satellite, cable, set-top box, etc.

OUT

VIDEO

OUT

+ 94 hidden pages