One Forall URC 8080 User Manual

Download

Page 1

INSTALLING THE BATTERIES

Your

A/V Producer

alkaline batteries. To install the batteries:

requires four (4) new AAA

URC 8080

A/V Producer

User Manual

1 On the back of the

Producer

the tab and slide the battery cover off.

2 Match the + and - marks

on the batteries to the + and - marks in the battery case, then insert the batteries.

, push down on

A/V

3 Slide the battery cover

back into place.

4 Test the unit by pressing

Note:

After inserting the batteries, the LCD screen will enter a test mode which tests each segment of the LCD screen. This process will last for 10 seconds or until any key is pressed, which e ver occurs first.

POWER. If the batteries are inserted correctly, the red light will blink.

Page 2

USING YOUR A/V PRODUCER

Feature Function

Features and Functions

The illustration below and the chart on the next two pages describe the features and the functions of the

A/V Producer’s

keypad. The following keys will always have the same function, regardless of which component you are controlling. For an explanation of what each key does by component type, please use the index at the rear of the manual (pages 45-57).

AMP TUN TV CBL

VCR SAT

HOME THEATER

ENTER

SLOW- SLOW SLOW+

REC

AUD

REW PL FF

EJECT X2

STOP

TV/SAT

VID

AUX1

MENU+

SUR

MENU-

PAU

DISP

EV C

EEZE

PIP

LITE

CBL

AMP

HOME THEATER

The MAGIC key is used to access the menu and program your

VCR

A/V Producer

The TV, VCR, CBL, SAT, AMP, TUN, CD, and AUX1 k eys are used to

select the home entertainment

SAT

component you want to control. If your component does not respond

TUN

when you press a key on the remote control, press either the TV,

AUX1

VCR, CBL, SA T, AMP, TUN, CD,

and AUX1 k ey to tell the remote control which component you would like to operate.

The HOME THEA TER key is used to select the Home Theater mode of the

A/V Producer

The ESC (Escape) key is used to exit the LCD Screen menu.

The LITE key is used to turn ON and OFF the

A/V Producer’s

backlit keypad and LCD screen. Press the LITE key once to turn ON the backlight. The

Producer’s

backlight will stay on for

A/V

10 seconds after the last key press and re-activates with the press of a key. To de-activate the backlight, press the LITE key again.

The POWER key controls power ON and OFF.

The VOL + (Volume Up), VOL- (Volume Down) and MUTE keys control the volume the same as the Volume Up and Down and Mute keys on your original remote .

Page 3

Feature Function (Cont.)

SETTING THE CLOCK

CH- CH+

The CH + (Channel Up) and CH- (Channel Down) keys change channels the same as the Channel Up and Down keys on your original remote.

AUD

The AUD and VID macro keys memorize up to 15 keystrokes that

VID

can be accessed in sequence at the press of a single key. These keys are not mode specific.

The SHIFT key accesses advanced features that are mapped under the following ke ys: CENTER, MENU,

SELECT, MUTE, PREV CH, PIP, REW, PLAY, FF, STOP and PAUSE.

Important:

For a detailed e xplanation of what function each key will perf orm by device type (TV, VCR, CBL, etc.), please refer to pages 45 through 57.

To set up the CLOCK/TIME on the display screen:

1 Press and hold MAGIC until the

display screen changes from [DEVICE and the TIME] to [TIMED SEQ].

2 Press the MENU - key twice, the

MENU-

x 2

display will change to [CONFIGURE]. Press SELECT, the display will

change to [THEATR SEL].

3 Press MENU - one time, the display

MENU-

will change to [TIME SET]. Press

SELECT again.

4 The display will change to [TIME]

0 - 9

and the first digit in the time will blink. Enter either a 0 or a 1, then the next digit in the time will begin to blink, continue entering the time until all four digits of the time have been set.

5 After the time has been set, AM/PM

will then blink. Press MENU - to toggle between AM and PM, once AM or PM is selected, press

MENU-

SELECT.

6 The display will then change to the

MENU-

day of the week (MON, TUES, WED, THURS, FRI, SAT or SUN). Use

MENU - to toggle through the days

until the proper day of the week is displayed on the screen, then press SELECT. The display will return to the [DEVICE and the TIME] screen with the correct time on the display.

NOTE: After changing the batteries, you will have to reprogram the clock.

Page 4

QUICK SET UP

To Quickly Set Up the A/V Producer to Operate Your Home Entertainment Components

1 Turn on all of the components that

you will be setting up.

2 Press and release the TV key. 3 Press and hold MAGIC until the

4 Press the MENU - key one time.

5 Enter the first TV code listed f or your

MENU-

VCR

display screen changes from [TV and the TIME] to [TIMED SEQ].

The display screen will change to [CODE SET UP]. Press SELECT.

The display will change to [DEV SETUP]. Press SELECT. The display will change to [TV}.].

brand in the “Set Up Codes f or TVs”

on pages 10-12, then press

SELECT. Point the remote control at

the TV and press POWER. Your Television should turn OFF. If your TV does not turn OFF, enter the next code in the code list then press SELECT followed b y POWER again. Once your TV turns OFF, press VCR. You will now enter your VCR code.

7 Continue to enter your codes as

illustrated in Steps 5 and 6 until the

A/V Producer

is operating all of your home entertainment components. Once you have finished setting up

your components, press ESC to return to the [DEVICE and TIME] display.

If you would like to setup each of your components individually, or if you purchase a component after you have set up the A/V Producer, see the "SETTING UP INDIVIDUAL HOME ENTERTAINMENT COMPONENTS" section on pages 10 - 22 in this manual.

Set Up Codes for TVs ....................... Pages 10 - 12

Set Up Codes for VCRs .................... Pages 13 - 14

Set Up Codes for Cable Boxes .................. Page 16

Set Up Codes for DSS and

Satellite Receivers............................... Page 17

Set Up Codes for Laser Disc Players......... Page 18

Set Up Codes for CD Players .................... Page 19

Set Up Codes for Tuner Receivers ............ Page 21

Set Up Codes for Amplifiers....................... Page 22

6 Enter the first VCR code listed for

your brand in the “Set Up Codes for

VCRs” on pages 13-14, then press

SELECT. Point the remote control

at the VCR and press POWER. Your VCR should turn OFF. If your VCR does not turn OFF, enter the next code in the code list then press

SELECT followed b y POWER again.

CBL

Once your VCR turns OFF, press CBL. You will now enter your Cable Box code.

Page 5

SETTING UP INDIVIDUAL HOME

ENTERTAINMENT COMPONENTS

To Set Up Your Television 1 Turn on your TV. 2 Press and release the TV key. 3 Press and hold MAGIC until the

4 Press the MENU - key one time.

5 Press SELECT and the display

6 Enter the first TV code listed f or your

For a detailed explanation of what function each key will perform in the TV mode, please refer to page 45 in the index.

Set Up Codes for TVs

A-Mark 003 Abex 032 Admiral 093, 016, 180,

Adventura 046 Aiko 092 Akai 030, 056, 145,

Alleron 179, 183 Ambassador 177 Anam 180

MENU-

display screen changes from [TV and the TIME] to [TIMED SEQ].

The display screen will change to [CODE SET UP]. Press SELECT.

The display will change to [DEV SET UP].

screen will change to [TV].

brand in the “Set Up Codes f or TVs” on pages 10-12, then press SELECT. Point the remote control at the TV

and press POWER. Your Television should turn OFF. If your TV turns OFF, press the ESC key to return the display to [TV and the TIME]. If your TV does not turn OFF, enter the next code in the code list then press SELECT followed b y POWER again. Once the correct code is entered, press the ESC key to return the display to [TV and the TIME].

Anam National 055

165, 179

151

AOC 030, 019, 185,

Archer 003 Audiovox 180, 003 Belcor 019, 030 Bell & Howell 016, 154, 179,

Bradford 180 Brockwood 019

080, 056, 003, 052

180

Set Up Codes for TVs (cont.)

Broksonic 236, 463, 180, Candle 030, 056, 186, Carnivale 030

Carver 054 , 187, 170 CCE 217 Celebrity 000 Citizen 092, 060, 030,

Clairtone 185 Concerto 056 Contec 180, 185, 157,

Craig 180 Crown 180, 039 Curtis Mathes 047, 060, 054,

CXC 180 Daewoo 451, 092, 019,

Daytron 056, 092 Dumont 017, 019 Dynatech 046 Electroband 000, 185 Electrohome 381, 389, 409 Emerson 463, 236, 180,

Envision 030 Fisher 154, 159 Fujitsu 179 Funai 171, 179, 180 Futuretech 180 GE 047, 451, 051,

Gibralter 017, 019, 030 Goldstar 056, 019, 030,

Grunpy 179, 180 Hallmark 178, 179, 236,

Harvard 180, 236, 178, Hitachi 145, 151, 056,

Infinity 054 Janeil 046 JBL 054 JCB 000 JVC 053, 036, 182,

Kawasho 158 Kaypani 052 KEC 180, 060 Kenwood 019, 030 Kloss 030, 046, 024 KMC 106 KTV 030, 039, 180,

Logik 016, 180, 236 Luxman 056 LXI 047, 054, 148,

003 046

056, 280, 186, 046, 039

158

154, 030, 039

039, 091

177, 179, 280, 178, 282, 154, 019, 185, 038, 039, 158, 181, 182, 183, 270

021, 027, 282, 055, 178, 029, 135, 174, 279

178, 001, 002, 032

019 179 032, 038, 279,

409, 413

169, 069, 160

183, 185, 217, 280

154, 156, 178

Magnasonic 054, 156, 179,

Magnavox 054, 096, 186,

Majestic 016, 017 Marantz 030, 054, 096,

Matsushita 250 Megatron 003, 145, 178 MEI 185, 051 Memorex 016, 056, 106,

MGA 150, 155, 178, Midland 017, 032, 039, Minutz 021

Mitsubishi 150, 155, 178,

Motorola 093, 055, 054, MTC 060, 056, 030, Multitech 180, 217, 019

NAD 156, 166, 178, NEC 019, 030, 036, Nikko 030, 092, 178

Noblex 430 Noshi 018 NTC 092 Onwa 180 Optimus 154, 166, 250,

Optonica 093, 165 Orion 236, 463, 180,

Panasonic 250, 051, 055, Penney 047, 051, 060,

Philco 054, 096, 030,

Philips 054, 096, 030,

Pilot 019, 030, 039 Pioneer 166, 038 Portland 092, 019, 039 Prism 051, 055 Proscan 047 Proton 003, 052, 178 Pulsar 092, 017, 019 Quasar 250, 051, 055,

RadioShack 019, 030, 032,

RCA 047, 018, 019,

092, 030, 093, 019, 003

030, 187, 020, 024, 028, 036, 386

187

150, 154, 178 030, 019, 093 047, 051, 135

030, 019, 093, 241

150, 051 019, 185, 091

019 056

463, 180, 179, 150, 165

179 054 019, 018, 030,

156, 021, 027, 178, 003, 135, 039, 002, 032, 149

019, 187, 020, 028

165 039, 047, 056,

154, 165, 178, 180, 409

029, 038, 090, 135, 147, 278, 093

Page 6

Set Up Codes for TVs (cont.)

Realistic 019, 030, 032,

Rhapsody 183, 185 Runco 017, 030 Sampo 030, 032, 039,

Samsung 060, 019, 030,

Samsux 039 Sanyo 154, 159, 146 Scimitsu 019 Scotch 178 Scott 019, 178, 179,

Sears 047, 054, 056,

Sharp 093, 039, 153, Shogun 019

Signature 2000 016, 047, 054, Simpson 186, 187, 030

Sony 000, 080 Soundesign 178, 179, 180,

Spectricon 003, 180, 030, Squareview 171

SSS 019, 180, 236 Starlite 180, 236, 019 Supre-Macy 046, 186 Supreme 000

039, 056, 154, 165, 178, 180

052 032, 056, 178,

427, 482

180, 236 146, 148, 149,

154, 156, 159, 171, 178, 179

157, 165, 386

019

186 019, 056

Sylvania 054, 096, 030,

Symphonic 171, 179, 180 Tandy 093, 165, 054,

Tatung 055, 051, 003 Technics 051, 250, 055 Technol Ace 179 Techwood 003, 051, 056 Teknika 092, 054, 060,

TMK 056, 177, 178, Toshiba 156, 154, 060, Tosonic 185

Totevision 039 Trical 157 Universal 027, 021, 047 Vector Research 030 Victor 053 Vidikron 054, 242 Vidtech 019, 036, 178 Viking 046 Wards 154, 016, 096,

Zenith 017, 092, 016 Zonda 003

187, 186, 020, 028

047, 039

056, 019, 015, 180, 179, 186, 150, 039, 312

236 036, 149

030, 056, 165, 019, 021, 027, 020, 178, 179, 080, 174, 028, 029

To Set Up Your VCR or TV/VCR Combinations

1 Turn on your VCR and insert a tape. 2 Press and release the VCR key.

VCR

3 Press and hold MAGIC until the

display screen changes from [VCR and the TIME] to [TIMED SEQ].

4 Press the MENU - key one time.

The display screen will change to [CODE SET UP]. Press SELECT. The display will change to

MENU-

[DEV SET UP].

5 Press SELECT and the display

screen will change to [VCR].

6 Enter the first VCR code listed for

your brand in the “Set Up Codes for VCRs” on pages 13-14, then press SELECT. Point the remote control at the VCR and press POWER or PLAY.

Your VCR should turn OFF or start to play. If your VCR turns OFF or starts

to play, press the ESC key to return the display to [VCR and the TIME]. If your VCR does not turn OFF or start to play, enter the next code in the code list then press SELECT followed by POWER or PLAY again. Once the correct code is entered, press the ESC key to return the display to [VCR and the TIME].

For a detailed explanation of what function each key will perform in the VCR mode, please refer to page 47 in the index.

Set Up Codes For VCRs

Admiral 048 Adventura 000 Aiko 278 Aiwa 000 Akai 041, 049, 053,

American High 035, 081 Asha 240 Audiovox 037, 038 Beaumark 240 Bell & Howell 104, 048, 046 Broksonic 184, 209, 121,

Calix 037 Candle 037, 038 Canon 035 Capehart 020 Carver 081 CCE 072, 278 Citizen 037, 278, 240,

Colt 072 Craig 037, 047, 072,

Curtis Mathes 035, 041, 060, Cybernex 051, 240

Daewoo 020, 045, 278, Daytron 020, 278

Dynatech 000 Electrohome 037, 240, 043 Electrophonic 037 Emerex 032 Emerson 184, 209, 479,

Fisher 047, 054, 066, Fuji 033, 035, 032, Funai 000, 278, 072, Garrard 000

061, 106

211, 295, 361, 002, 479

035, 000

240, 271 202

046

000, 002, 036, 037, 043, 061, 068, 121, 208, 211, 212, 278, 294, 295, 361

104, 046 034 240

GE 035, 060, 065, Go Video 232, 279, 240, Goldstar 037, 038, 278

Gradiente 000 Harley Davidson 000 Harman/Kardon 038, 075 Harwood 068, 072 Havard 072 Headquarter 046 HI-Q 047 Hitachi 042, 000, 041,

Jensen 041, 008, 067 JVC 008, 041, 067,

KEC 037, 278 Kenwood 038, 041, 067,

KLH 072 Kodak 035, 037 Lloyds 208, 072, 038 Logik 072 LXI 037, 035, 042,

Magnasonic 240, 037, 278, Magnavox 035, 039, 081, Magnin 240

Marantz 035, 081 Marta 037 Matsushita 035, 162, 454,

MEI 035 Memorex 000, 035, 037,

MGA 043, 061 MGN T echnology 240 Minolta 042, 105 Mitsubishi 043, 061, 067,

202, 048 526

065, 105, 166, 396

206

008

046, 047, 054, 066, 104, 105

020, 072 110, 149

081, 110

039, 046, 047, 048, 104, 240

075, 173, 008, 048

Page 7

Set Up Codes For VCRs (Cont.)

Motorola 035, 048 MTC 000, 240 Multitech 000, 072 NAD 104 NEC 038, 040, 041,

Nikko 037 Nikon 034 Noblex 240 Olympus 035 Optimus 037, 048, 104,

Optonica 062 Orion 184, 209, 000,

Panasonic 035, 162, 254, Penney 035, 037, 038,

Pentax 042, 065, 105 Philco 035, 081, 110 Philips 035, 062, 081,

Pilot 037 Pioneer 067, 008 Portland 020 Protec 072 Pulsar 039, 051, 240,

Quarter 046 Quartz 046 Quasar 035, 162, 454 RadioShack 000, 037, 035,

Radix 037 Randex 037 RCA 060, 202, 042,

Realistic 000, 035, 037,

Ricoh 034, 035

067, 104, 008

162, 454

479, 002, 036, 037, 043, 061, 068, 121, 028, 211, 212, 278, 294, 295, 361

378, 454 040, 042, 054,

240

110

278

048

149, 048, 065, 105, 106, 035

046, 047, 048, 062, 066, 104, 240

Runco 039 Salora 075 Samsung 240, 045, 051,

Sanky 039, 048 Sansui 041, 067, 271,

Sanyo 104, 046, 047, Scott 043, 045, 121,

Sears 035, 037, 042,

Sharp 048, 062 Shintom 072, 000, 240 Shogun 051, 240 Singer 072, 037, 240 Sony 032, 033, 034,

STS 042 Sylvania 000, 035, 043,

Symphonic 000 Tatung 041, 067, 000 TEAC 000, 041 Technics 035, 162, 454 Teknika 000, 035, 037 TMK 036, 208, 240 Toshiba 043, 045, 060,

Totevision 037, 240 Unitech 240 Vector 045 Vector Research 038, 040 Video Concepts 040, 045, 061 Videosonic 240, 000, 072 Wards 000, 035, 042,

XR-1000 000, 035, 072, Yamaha 038

Zenith 039, 033, 034,

053

209, 072, 002, 479, 008

054, 240 184, 210, 211,

212 046, 047, 054,

066, 104, 105, 000

035

081, 110

066, 210, 212, 366

047, 048, 060, 062, 072, 149, 212, 240, 202

240

000

Set Up Codes for TV/VCR Combinations

American High 035* Broksonic 002, 294, 479 Colt 072 Curtis Mathes 035* Daewoo 278 Emerson 002, 294, 479 Funai 000 GE 035*, 060*,

Harley Davidson 000 Hitachi 035*, 000 HQ 000 Lloyd's 000 Magnavox 000, 035*, 081* Magnin 240

Note*:

TV/VCRs working on 032 will need TV code 000 for volume control. TV/VCRs working on 035 will need TV code 051 for volume control. TV/VCRs working on 048 will need TV code 093 for volume control. TV/VCRs working on 060 will need TV code 047 for volume control. TV/VCRs working on 081 will need TV code 054 for volume control. TV/VCRs working on 162 will need TV code 250 for volume control. TV/VCRs working on 294 will need TV code 236 for volume control.

048*, 240

Memorex 037, 162* MGA 240 Mitsubishi 048* Orion 002, 294, 479 Panasonic 035*, 162* Penney 035*, 240, 162* Quasar 035*, 162* RCA 060*, 035*,

Sansui 000, 479 Sanyo 240 Sears 000, 037 Sony 032 Symphonic 000 Zenith 000, 037

048*

To Set Up Your Cable Box: 1 Turn on your Cable Box. 2 Press and release the CBL key.

CBL

3 Press and hold MAGIC until the

display screen changes from [CBL and the TIME] to [TIMED SEQ].

4 Press the MENU - key one time.

The display screen will change to [CODE SET UP]. Press SELECT. The display will change to

MENU-

[DEV SET UP].

5 Press SELECT and the display

6 Enter the first Cable Box code listed

screen will change to [CBL].

for your brand in the “Set Up Codes

POW

for Cable Boxes” on page 16, then press SELECT. Point the remote

control at the Cable Box and press POWER. Your Cable Box should turn OFF. If your Cable Box turns OFF, press the ESC key to return the display to [CBL and the TIME]. If your Cable Box does not turn OFF, enter the next code in the code list then press SELECT followed by POWER again. Once the correct code is entered, press the ESC key to return the display to [CBL and the TIME].

Note:

If your original Scientific Atlanta remote control

does not have an “ON” key, press

CH+

or one of the digit keys on the A/V Producer to turn your Cable Box on.

For a detailed explanation of what function each key will perform in the Cable mode, please refer to page 45 in the index.

Page 8

Set Up Codes For Cable Boxes

SAT

ABC 003, 014, 007,

Allegro 153, 000, 315, Antronix 022, 207

Archer 022, 153, 207, Cabletenna 022

Cableview 022 Century 153 Citizen 153, 315 Colour Voice 025, 031 Comband 232, 233 Comtronics Eagle 040, 060, 008 Contec 019 Eastern 002 Everquest 015, 040 Focus 400 Garrard 153 GC Electronics 207 GE 232, 233 Gemini 015, 057, 242 General Instrument 476, 276, 003,

Goldstar 040, 144 Hamlin 009, 020, 034,

Hitachi 011 Hytex 007 Infinity 770 Jasco 153, 315 Jerrold 003, 014, 476,

Macom 033 Magnavox 027, 334 Memorex 000 Movie Time 063, 156 Novaplex 618 Novavision 008, 017, 477 NSC 063, 156 Oak 007, 019 Omega 015 Panasonic 000, 021, 107 Panther 637 Paragon 000

008, 011, 017, 001, 013

191

797

014, 011

259, 273

012, 011, 015, 024, 276

Philips 025, 027, 031,

Pioneer 533, 144, 023, Popular Mechanics 400

Prelude 770 Pulsar 000 RadioShack 797 RCA 021 Realistic 207 Recoton 400 Regal 020, 259, 273,

Regency 002 Rembrandt 011, 153 Runco 000 Samsung 040, 144 Scientific Atlanta 008, 477, 017,

Signal 015, 040 Signature 011 SL Marx 040 Sprucer 021, 307 Starcom 003, 015 Stargate 015, 040, 770 Starquest 015 Starsight 542 Sylvania 001 Tandy 258 TeleCaption 221 Teleview 040, 063 Texscan 001 Timeless 418 Tocom 012, 013 Toshiba 000 Tusa 015 TV86 063, 040 Unika 022, 153, 207 United Artists 007 United Cable 003 Universal 022, 077, 153,

Videoway 250 Viewstar 027, 060, 063,

Zenith 000, 525 Zentek 400

153, 242, 290, 334

260

279

006

191, 207

211, 258

To Set Up Your DSS or Satellite Receiver 1 Turn on your DSS or Satellite

Receiver.

2 Press and release the SAT key. 3 Press and hold MAGIC until the

display screen changes from [SAT and the TIME] to [TIMED SEQ].

4 Press the MENU - key one time.

MENU-

The display screen will change to [CODE SET UP]. Press SELECT.

The display will change to [DEV SET UP].

5 Press SELECT and the display

6 Enter the first Satellite code listed

POW

screen will change to [SAT].

for your brand in the “Set Up Codes for Satellites” on page 17, then press SELECT. Point the remote

control at the Satellite and press POWER. Your Satellite should turn OFF. If your Satellite turns OFF, press the ESC key to return the display to [SAT and the TIME]. If your Satellite does not turn OFF, enter the next code in the code list then press SELECT followed by POWER again. Once the correct code is entered, press the ESC key to return the display to [SAT and the TIME].

For a detailed explanation of what function each key will perform in the Satellite mode, please refer to page 55 in the index.

Set Up Codes for DSS and Satellite Receivers

AlphaStar DSS 772 Amplica 072 Amway 043, 075 Astro Industries 095 BSR 095 Cable Innovations 554, 555 Capetronic 095 Century 538 Channel Master 018, 212 Chaparral 053, 209, 216 Citoh 164 Conifer 004 Curtis Mathes 061, 072 Drake 018, 064, 149,

245 DX Antenna 041 Echostar 148, 159, 269,

280 Echostar DSS 775 General Instrument 050, 361, 554,

555 Hitachi DSS 819, 749 Homecable 238 HTS DSS 775 Hughes DSS 749, 819 Hytek 095 Intersat 043 IQ 210 Janeil 152 Jerrold Primestar 627

Jerrold 361 Legend 269 Macom 018, 050, 061 Magnavox DSS 724, 722 Memorex 269 Norsat 004 Panasonic 152 Panasonic DSS 701 Pansat 647 Philips 200 Philips DSS 724, 722 Pico 075 Primestar DSS 627 Prosat 158 RadioShack 554 Ramsey 075 RCA DSS 566 Realistic 051, 052 Sony DSS 639 Star Trak 180, 421, 547 Strong 421 STS 041, 210 Toshiba 061, 082 T oshiba DSS 790 Uniden 052, 074, 076,

238, 296, 370,

554, 555 Uniden DSS 724, 722 Zenith 061, 064

Page 9

To Set Up Y our Laser Disc Player:

POW

To Set Up Your CD Player:

1 Turn on your Laser Disc Player and

insert a disc.

2 Press and release the AUX 1 key.

AUX1

3 Press and hold MAGIC until the

display screen changes from [LDP and the TIME] to [TIMED SEQ].

4 Press the MENU - key one time.

The display screen will change to [CODE SET UP]. Press SELECT. The display will change to

MENU-

[DEV SET UP].

5 Press SELECT and the display

6 Enter the first Laser Disc code listed

screen will change to [LDP].

for your brand in the “Set Up Codes for Laser Disc Players” on page 16, then press SELECT. Point the

remote control at the Laser Disc Player and press POWER or PLAY. Your Laser Disc Player should turn

OFF or play your disc. If your Laser Disc Player turns OFF or plays your disc, press the ESC key to return the display to [LDP and the TIME]. If your Laser Disc Player does not turn OFF or play your disc, enter the next code in the code list then press

SELECT followed b y POWER or PLAY again. Once the correct code

is entered, press the ESC key to return the display to [LDP and the TIME].

1 Turn on your CD Player and insert a

disc.

2 Press and release the CD key.

3 Press and hold MAGIC until the

display screen changes from [CD and the TIME] to [TIMED SEQ].

4 Press the MENU - key one time.

The display screen will change to [CODE SET UP]. Press SELECT. The display will change to

MENU-

[DEV SET UP].

5 Press SELECT and the display

6 Enter the first CD code listed for

screen will change to [CD].

your brand in the “Set Up Codes for CD Players” on pages 19-20, then press SELECT. Point the remote control at the CD Player and press PLAY. Your CD Player should start to play your disc. If your CD Player plays your disc, press the ESC key to return the display to [CD and the TIME]. If your CD Player does not play your disc, enter the next code in the code list then press SELECT followed by PLAY again. Once the correct code is entered, press the ESC key to return the display to [CD and the TIME].

For a detailed explanation of what function each key will perform in the CD mode, please refer to page 56 in the index.

For a detailed explanation of what function each key will perform in the AUX1 mode , please refer to page 50 in this index.

Set Up Codes for Laser Disc Players

Aiwa 203 Carver 064, 194, 323 Denon 172, 241 Disco Vision 023 Funai 203 Hitachi 023 Magnavox 194, 217, 241 Marantz 064, 194 Mitsubishi 059 NAD 059 NEC 286

Panasonic 204 Philips 064, 194 Pioneer 059, 023 Quasar 204 RCA 128, 351 Realistic 203 Samsung 323 Sega 023 Sony 193, 201, 270 Theta Digital 194 Yamaha 217

Set Up Codes for CD Player

Acoustic Research 123 ADC 018, 033 Adcom 155, 234 Aiwa 012, 124, 157 Akai 156, 676 Alpine 341 Audio Alchemy 194 Audio-Technica 170 BSR 194, 245 Burmester 420 California Audio Lab 029 Capetronic 237 Carrera 194 Carver 157, 179, 299,

365, 437

Craig 615

Crown 122 DAK 245 Denon 003, 034 DKK 000 Emerson 155, 164, 305,

Fisher 048, 088, 174, Garrard 245, 280, 393, GE 009, 334

Genexxa 032, 164, 305 Goldstar 030, 417, 525 Gradiente 558 Harman/Kardon 108, 426 Hitachi 032, 139, 155

469 179, 342 420, 425, 633

Page 10

Set Up Codes for CD Player (Cont.)

Inkel 065 JVC 072, 655, 658 Kenwood 028, 037, 048,

190, 337, 338,

339, 340, 523 Kodak 287 Koss 734 Krell 157 Kyocera 018 Luxman 093, 149, 327 LXI 305 Magnavox 038, 129, 157,

526 Marantz 005, 029, 038,

157, 180, 435 McIntosh 287 MCS 029, 043, 345,

454 MGA 083 Mission 157 Mitsubishi 083, 098 MTC 420 NAD 019, 299 Nakamichi 147 NEC 043, 130, 234 Nikko 164, 169, 170,

174, 525 NSM 157 Onkyo 101, 102, 138,

381 Optimus 000, 032, 037,

087, 175, 179,

194, 196, 280,

305, 342, 420,

426, 437, 468,

536 Panasonic 029, 367, 388,

752 Parasound 194 Philco 603, 734 Philips 157, 274, 287 Pioneer 032, 244, 305,

468, 551

Proton 152, 157 QED 157 Quasar 029 RCA 009, 053, 155,

179, 305, 764

Realistic 155, 164, 175,

179, 180, 237,

420 Rotel 157, 420 SAE 157 Samsung 524 Sansui 157, 202, 216,

305 Sanyo 087, 179 Schneider 560 Scott 155, 164, 305 Sears 305 Sharp 037, 180, 262,

265 Sherwood 065, 114, 180,

196, 426 Shure 043 Signature 108 Signature 2000 108 Sony 000, 185, 490,

604, 605, 727 Soundesign 145, 425 STS 018 Symphonic 183 Tascam 420 TEAC 016, 045, 153,

174, 180, 183,

378, 393, 420 Technics 029, 207, 303 Toshiba 019, 299 Vector Research 033, 194, 417 Victor 072 Wards 108 Yamaha 036, 170, 187,

261 Yorx 461 Zenith 615

T o Set Up Your Tuner/Receiver 1 Turn on your Tuner/Receiver.

2 Press and release the TUN key.

TUN

3 Press and hold MAGIC until the

display screen changes from [TUN and the TIME] to [TIMED SEQ].

4 Press the MENU - key one time.

The display screen will change to [CODE SET UP]. Press SELECT. The display will change to

MENU-

[DEV SET UP].

5 Press SELECT and the display

screen will change to [TUNER].

6 Enter the first Tuner code listed for

POW

your brand in the “Set Up Codes for Tuner/Receivers” on page 21, then press SELECT. Point the remote

control at the Tuner/Receiver and press POWER. Your Tuner/Receiver should turn OFF. If your Tuner/ Receiver turns OFF, press the ESC key to return the display to [TUN and the TIME]. If your Tuner/ Receiver does not turn OFF, enter the next code in the code list then press SELECT followed by POWER again. Once the correct code is entered, press the ESC key to return the display to [TUN and the TIME].

For a detailed explanation of what function each key will perform in the Tuner mode, please refer to page 54 in the index.

Set Up Codes for Tuner/Receivers

ADC 531 Adcom 616 Admiral 182 Aiwa 121, 125, 158,

189, 405 Akai 076, 224 Bose 639 Capetronic 531 Carver 008, 042, 189,

360, 412 Casio 195, 201 Clarinette 195 Curtis Mathes 201 Denon 004, 273, 771,

386 Emerson 255, 424 Fisher 042, 219, 360 Garrard 281, 424, 440,

463 Goldstar 281, 386 Harman/Kardon 110 Hitachi 386 Inkel 062 JVC 074, 464 Kenwood 027, 077, 186,

313, 314 Koss 255, 424 Lloyd 195 Luxman 166 LXI 181 Magnavox 128, 189, 195,

531 Marantz 189, 006, 039,

128, 200, 412 MCS 039, 201, 346 Modulaire 195 NAD 320 Nakamichi 347

NEC 235 Onkyo 135, 100, 119,

380

Optimus 080, 177, 181,

186, 219, 440,

531, 670 Panasonic 039, 518, 309 Penney 195, 201 Philips 189, 412 Pioneer 014, 080, 150,

289, 531, 630 Quasar 039 RCA 054, 346, 360,

530, 531 Realistic 163, 181, 182,

195 Sansui 189, 346 Sanyo 219 Scott 105, 163, 322,

390 Sears 201 Sharp 186 Sherwood 062, 491, 502 Sonic 281 Sony 158, 238 Soundesign 670 Symphonic 182 TEAC 463, 163, 298,

387 Technics 039, 208, 309,

518 Techwood 281 Victor 074 Wards 014, 042, 054,

080, 158, 189 Yamaha 176, 081, 082,

186 Yorx 195 Zenith 281

Page 11

To Set Up Your Amplifier

POW

1 Turn on your amplifier. 2 Press and release the AMP key.

AMP

3 Press and hold MAGIC until the

display screen changes from [AMP and the TIME] to [TIMED SEQ].

4 Press the MENU - key one time.

The display screen will change to [CODE SET UP]. Press SELECT. The display will change to

MENU-

[DEV SET UP].

5 Press SELECT and the display

screen will change to [AMP].

6 Enter the first Amplifier code listed

for your brand in the “Set Up Codes for Amplifiers” on page 22, then press SELECT. P oint the remote

control at the Amplifier and press POWER. Your Amplifier should turn OFF. If your Amplifier turns OFF, press the ESC key to return the display to [AMP and the TIME]. If your Amplifier does not turn OFF, enter the next code in the code list then press SELECT followed by POWER again. Once the correct code is entered, press the ESC key to return the display to [AMP and the TIME].

For a detailed explanation of what function each key will perform in the Amplifier mode, please refer to page 55 in the index.

Set Up Codes for Audio Amplifiers

Accuphase 382 Acurus 765 AudioSource 011 Carver 269 Denon 160 Elan 647 Forte 606 GE 078 Goldstar 031 Harman/Kardon 106 JVC 331 Kenwood 356 Luxman 165 Magnavox 269 Marantz 269, 321 McIntosh 251

Nakamichi 321 NEC 264 Optimus 013, 300, 395 Panasonic 308 Philips 269 Pioneer 013, 300 Realistic 395 Sansui 321 Shure 264 Sony 220, 689 Soundesign 078, 211 Technics 308 Victor 331 Wards 013, 078, 211 Yamaha 133, 143, 354,

504

SETTING UP ADDITIONAL HOME ENTERTAINMENT COMPONENTS

Besides the device keys that are already labeled (TV, VCR, CBL, etc.), the operate the following components: DVD Players, Cassette Decks, Home Automation, Digital Audio Tape, Phonographs, Video Accessories and Miscellaneous Audio Components (Graphic Equalizers and Digital Music Service Boxes).

The Set Up codes for these devices can be accessed under the following device keys:

DVD Players: Use the AUX1 Key Cassette Decks: Use the AUX1 Key Home Automation: Use the CD Key Digital Audio Tape: Use the AUX1 Key Phonographs: Use the CD Key Video Accessories: Use the CBL Key Miscellaneous Audio: Use the AMP Key

Note:

Each device key (TV, only operate one component at a time. If you have already set up a component on a key, then assigning a second component on the same key will erase the code for the first component you set up. For example, if you set up a Laser Disc Player on and then set up a DVD Player on Producer will only operate the DVD Player.

For example, to set up a DVD Player on the AUX1 key: 1 Turn on your DVD Player and insert

a disc.

2 Press and release the AUX1 key.

AUX1

3 Press and hold MAGIC until the

display screen changes from [LDP and the TIME] to [TIMED SEQ].

4 Press the MENU - key one time.

The display screen will change to [CODE SET UP]. Press SELECT. The display will change to

MENU-

[DEV SET UP].

5 Press SELECT and the display

screen will change to [LDP].

A/V Producer

VCR, CBL

AUX1

can also

etc.) can

AUX1

, the A/V

Page 12

6 Press MENU - to toggle between

POW

MENU-

[LDP], [D VD], [TAPE] and [DAT]. Once [DVD] is on the display

screen, enter the first DVD Player code listed for your brand in the “Set Up Codes for DVD Players” on page 25, then press SELECT. Point the remote control at the DVD Player and press POWER or PLAY. Y our DVD Player should turn OFF or play

your disc. If your DVD Player turns OFF or plays your disc, press the ESC key to return the display to [DVD and the TIME]. If your DVD Player does not turn OFF or play your disc, enter the next code in the code list then press SELECT followed b y POWER or PLAY again. Once the correct code is entered, press the ESC key to return the display to [DVD and the TIME].

Re-assigning Device Keys

You can use the

A/V Producer

to operate a second TV or a second VCR or any combination of eight devices. To do this, you must re-assign one of the device keys (TV, VCR/LD, CBL, SAT, AMP, TUN or CD) to operate your second device. For example, to re-assign one of the device keys to support your other components:

1 Press and hold MAGIC until the

display screen changes from [DEVICE and the TIME] to [TIMED SEQ].

2 Press the MENU - key twice. The

MENU-

x 2

display screen will change to

[CONFIGURE]. Press SELECT. The display will change to [THEATER SEL].

3 Press the MENU - key three times.

MENU-

x 3

The display screen will change to [MODE MAP]. Press SELECT. The

display screen will change to [SOURCE].

(Device Key)

4 Press the device key you would like

to move (for DVD Players it would be AUX1 or for a second TV, it would be the TV key). The display screen will change to [COPY TO]. Now press the unused device key you would like to replace. The display will change to [DEVICE2 and the TIME]. Now, proceed with programming the re-assigned device key with the appropriate code.

Note:

Initially, moving

AUX 1

to another key will display [LDP2]. To access [DVD2], you must follow instructions on page 25 to access "Additional Home Entertainment Components."

Set Up Codes for DVD Players

Philips 482 Panasonic 490

Toshiba 503

Set Up Codes for Cassette Decks

ADC 171 Aiwa 029, 197, 200 Akai 283 Carver 029, 261 Denon 076, 421 Fisher 074, 261 Garrard 300, 308, 309,

375, 439, 448 Goldstar 421 JVC 244, 273, 274,

303, 310 Kenwood 070, 071, 092,

233, 234 Kyocera 171 Magnavox 029 Marantz 029 MGA 313 Mitsubishi 283, 313

Nakamichi 147, 151, 218,

247, 248 Onkyo 136, 282 Optimus 027, 220, 300,

337, 439 Philips 029 Pioneer 027, 099, 220 RCA 261 Sansui 029 Sharp 231 Sherwood 337 Sonic 375 Sony 170, 243, 291 TEAC 280, 289, 308,

309 Technics 229, 353 Victor 273, 274 Wards 027 Yamaha 094, 097

Set Up Codes for Home Automation

Audio Access 154 GE 240 LiteTouch 084 Lutron 318 One For All X10 Security System 167

ProPresenter 607, 672 RadioShack 240 Sanyo 336 Universal X10 167 X10 167

Set Up Codes for Digital Audio Tape

Carver 158 Marantz 158 Philips 158

Set Up Codes for Phonographs

Aiwa 188 Carver 188 Magnavox 188

Marantz 188 Philips 188

Page 13

Set Up Codes for Video Accessories

Rabbit 081 Roctec 456

SuperGuide 169 TeleCaption 171

Set Up Codes for Miscellaneous Audio

Adcom 577 Aiwa 010, 159 AudioSource 351 BSR 392 Cambridge Soundworks 351 Carver 351 Fisher 052 Fosgate 259, 447 HarmanKardon 447 JBL 447 Jerrold 459, 520 JVC 073 KLH 351 Magnavox 325

Nikko 376 Paramount Pictures 317, 351

RCA 056 Sansui 325 Schneider 376 Scientific Atlanta 460 Sony 010, 159 Soundesign 376 Soundstream 447 SSI 317 Starcom 459 Yamaha 292 Yorx 376

SEARCHING FOR YOUR CODE

If your components do not respond to the

Producer

after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, after trying all of the codes for your brand of TV, you still cannot get the

1 Press and release the TV key. 2 Press and hold MAGIC until the

A/V Producer

to operate your TV, then:

display screen changes from [TV and the TIME] to [TIMED SEQ].

3 Press the MENU - key one time.

The display screen will change to [CODE SET UP]. Press SELECT. The display will change to

MENU-

[DEV SET UP].

4 Press the MENU - key one time.

The display screen will change to [DEV SEARCH]. Press SELECT. The display will change to

MENU-

[TV and XXX].

A/V

Note:

XXX represents the last 3 digit code that was

entered prior to starting the search.

5 Press POWER. If your TV turns

POW

OFF, press SELECT to lock in your code and return the display to [TV and the TIME]. If your TV does not turn OFF, press MENU -. The next available code will appear on

MENU-

the display screen, then press

POWER again. Continue to press POWER then MENU - until your TV

turns OFF. Once your TV turns OFF, press SELECT to lock in your code and return the display to [TV and the TIME].

Note:

If you are searching for your VCR, CD Player, Laser Disc Player or DVD Player code, you may want to use component plays, press

PLAY

instead of

SELECT

POWER

. Once your

to lock in your

code.

Page 14

Finding Your Code

SETTING UP THE HOME THEATER MODE KEY

After you have set up your components using the search, you may need to find out which three-digit code is operating your components. For example, to find out what three-digit code is operating your TV:

1 Press and release the TV key.

2 Press and hold MAGIC until the

display screen changes from [TV and the TIME] to [TIMED SEQ].

3 Press the MENU - key one time.

The display screen will change to [CODE SET UP]. Press SELECT. The display will change to

MENU-

[DEV SET UP].

4 Press the MENU - key two times .

MENU-

x 2

The display screen will change to [DEV NUMBER]. Press SELECT.

The display screen will then change to [TV and your code]. Once you have written your three-digit code down, press ESC to return the display to [TV and the TIME].

TV code

VCR Code

Cable Code

Satellite Code

Tuner Code

The HOME THEATER mode key brings all of the most commonly used home theater functions into one mode of the

A/V Producer

. When setting up the HOME THEATER mode key, you will choose which components will control your volume, channel changing, Playback, Picture-in-Picture and menu functions.

1 Press and release the HOME

HOME THEATER

2 Press and hold MAGIC until the

THEATER mode key.

display screen changes from [THEATER and the TIME] to [TIMED SEQ].

3 Press the MENU - key twice, the

MENU-

x 2

display will change to [CONFIGURE]. Press SELECT, the

x 2

display will change to [THEATR SEL], press SELECT. The display will change to [AUDIO].

4 Press SELECT. This will change the

display to [AMP]. At this screen you will select the device that will control

(Device Key)

your Volume in the Home Theater Mode. Use the de vice ke ys (AMP,

TUNER, TV, CABLE, SA T or AUX 1)

to choose your AUDIO selection. Once you choose the AUDIO source, press SELECT. For e xample, if your Tuner will control your volume in the Home Theater Mode, press TUN + SELECT. The display will change to [CHANNEL]. This will allow you to choose the device that will control your channel changing.

(continued on next page)

Amplifier Code

CD Player Code

AUX1 Code

Page 15

5 Press SELECT. This will change the

(Device Key)

display to [SAT]. Use the device keys (TV, VCR, SAT, CBL or AUX 1) to choose your CHANNEL source,

then press SELECT. For example, if your Satellite will control your channel changing in the Home Theater Mode, press SAT + SELECT. The display will change to [PLAYBACK]. This will allow you to choose the device that will control the transport keys (PLAY, REW, FF,

PAUSE, ST OP and REC).

6 Press SELECT. This will change the

(Device Key)

display to [VCR]. Use the device keys (CD, VCR or AUX 1 [LD]) to choose your PLAYBACK source,

then press SELECT. For example, if your Laser Disc Player will control your playback in the Home Theater Mode, press A UX 1 + SELECT. The display will change to [PIP]. This will allow you to select the device that will control your Picture-in-Picture features.

7 Press SELECT. This will change the

(Device Key)

display to [TV]. Use the device keys (TV, CBL or VCR) to choose your PICTURE-IN-PICTURE source,

then press SELECT. F or example, if your VCR will control your Picturein-Picture features in the Home Theater Mode, press VCR + SELECT. The display will then return to [MENU]. This will allow you to select the device that will control your Menu features.

8 Press SELECT. This will change the

display to [SAT]. Use the device k e ys (TV, CBL, SAT, VCR, TUNER or

(Device Key)

AUX1) to choose y our MENU source, then press SELECT. For

example, if your DSS will control your Menu features in the Home Theater mode, press SAT + SELECT. The display will then return to the [DEVICE and the TIME] SCREEN.

After you have set up the HOME THEATER mode key, you can then set up a macro sequence on the

POWER key in the Home Theater Mode. The POWER key macro will allow you to power ON all of

your components in the Home Theater mode with the press of one key.

Power Key Macro - Powering ON Your Home Theater Components with One Key Press

1 Press and release the HOME

HOME THEATER

THEATER Mode key, then press

and hold MAGIC until the display screen changes from [THEATER and the TIME] to

x 2

[TIMED SEQ]. Press the MENU -

MENU-

key twice, the display will change to [CONFIGURE]. Press SELECT, the

2 Press MENU - four times until the

MENU-

3 Press the POWER key to assign the

POW

display will change to [THEATR SEL].

x 4

display reads [KEY MACRO]. Press SELECT. The display will read [SEL MACKEY].

macro to POWER. Enter the macro sequence that will power “ON” your home theater, f or example:

(Sequence)

TUN + POWER + TV + POWER + VCR + POWER + Etc. until you hav e

added all of your home theater components.

Page 16

4 When your macro sequence is

POW

concluded, press ESC to save. The display will then return to the [THEATER and the TIME] screen.

To activate the Home Theater Power macro, the LCD screen must read [THEATER], and you must press

POWER.

Note:

The

AUD

VID

macro keys cannot be used

in your Home Theater Power key macro.

SETTING UP TIMED SEQUENCES RECORDING WHEN YOU ARE NOT HOME

The

A/V Producer

that lets the user set up a sequence of key strokes that can be played back at a specified time, up to seven days in advance. This feature can be used to set up sequences that will record from your DSS satellite, turn on your infrared home automation lighting system when you are not home or any other series of keystrokes that you would like to play back at a later time. For example, to set up the remote to record a program off of your DSS Satellite:

is equipped with a special feature

1 Press and hold MAGIC until the

display screen changes from [DEVICE and the TIME] to [TIMED SEQ]. Press SELECT. The

display will change to [ADD MACRO]. Press SELECT again.

0 or 11

2 The display will change to

[START and the TIME], with the first digit of the TIME blinking. Enter either a 0 or a 1, then the next digit in the time will begin to blink,

MENU-

continue entering the time until all four digits of the time have been set. After the time has been set, AM/PM will then blink. Press MENU - to toggle between AM and PM, once AM or PM is selected, press SELECT.

3 The display will then change to

MENU-

[ONCE]. Use the MENU - key to toggle between [ONCE], [DAILY] or

[WEEKLY], depending on when and how often the sequence needs to play. After [ONCE], [DAILY] or [WEEKLY] is chosen, press SELECT.

4 The display will change to the day of

MENU-

the week that you want the sequence to begin. Use MENU - to

toggle through the days of the week until the proper day is on the display screen. Press SELECT. The display will change to [ENTER SEQ].

(continued on next page)

Page 17

For example, enter a sequence that will start your VCR recording your DSS Satellite channel.

SAT + POWER + SAT + 2 + 7 + 5 + VCR + PO WER + VCR + RECORD.

This sequence will turn on the DSS, change the channel to 275, turn on the VCR and start the VCR recording.

Note:

When setting up your sequence, you will need to include any keystrokes that would normally be required during regular usage, such as pressing

ENTER

after entering a channel number when changing channels.

5 Once the sequence has been set

up, press the ESC key to return to the [DEVICE and the TIME] display screen. Below the [TIME], a

CLOCK ( ) symbol will appear to show that there is a timed sequence in the memory.

To Delete a Timed Sequence 1 Press and hold MAGIC until the

display screen changes from [DEVICE and the TIME] to

[TIMED SEQ]. Press SELECT. The display will change to [ADD MA CRO].

MENU-

2 The display will then change to

Press MENU - one time. The display will change to [DEL MACRO]. Press SELECT.

[DEL (the DAY) and (the TIME)]. If this is the timed sequence you would like to delete, press SELECT. The display will change to [DELETED] then return to [DEVICE and the TIME].

Note: If you have more than one timed sequence saved in the memory of the A/V Producer, use the

MENU -

key to scroll through your saved timed sequences until you see the sequence you would like to delete. Once the sequence is displayed on the screen, press

SELECT

. The display will change to [DELETED] then return to the next available sequence to be deleted. If there are no other sequences to be deleted, then the display will return to [DEVICE and the TIME].

Note:

If, at any time during the set up of your timed

sequence, a mistake is made, press the

ESC

key to return to the main display [DEVICE and the TIME] . Now, delete the sequence that was incorrect and restart your timed sequence.

After you have set up a timed sequence, you may want to set up a second sequence that turns everything off after your initial sequence is complete. For the example above, after recording the program from your DSS, you can set up a second sequence to power OFF your DSS and VCR. Repeat Steps 1 - 5 to set up a sequence to power OFF your components.

Page 18

For example, enter a sequence that will start your VCR recording your DSS Satellite channel.

SAT + POWER + SAT + 2 + 7 + 5 + VCR + PO WER + VCR + RECORD.

This sequence will turn on the DSS, change the channel to 275, turn on the VCR and start the VCR recording.

Note:

When setting up your sequence, you will need to include any keystrokes that would normally be required during regular usage, such as pressing

ENTER

after entering a channel number when changing channels.

5 Once the sequence has been set

up, press the ESC key to return to the [DEVICE and the TIME] display screen. Below the [TIME], a

CLOCK ( ) symbol will appear to show that there is a timed sequence in the memory.

To Delete a Timed Sequence 1 Press and hold MAGIC until the

display screen changes from [DEVICE and the TIME] to

[TIMED SEQ]. Press SELECT. The display will change to [ADD MA CRO].

MENU-

Press MENU - one time. The display will change to [DEL MACRO].

2 The display will then change to

Press SELECT.

[DEL (the DAY) and (the TIME)]. If this is the timed sequence you would like to delete, press SELECT. The display will change to [DELETED] then return to [DEVICE and the TIME].

Note: If you have more than one timed sequence saved in the memory of the A/V Producer, use the

MENU -

key to scroll through your saved timed sequences until you see the sequence you would like to delete. Once the sequence is displayed on the screen, press

SELECT

. The display will change to [DELETED] then return to the next available sequence to be deleted. If there are no other sequences to be deleted, then the display will return to [DEVICE and the TIME].

Note:

If, at any time during the set up of your timed

sequence, a mistake is made, press the

ESC

key to return to the main display [DEVICE and the TIME] . Now, delete the sequence that was incorrect and restart your timed sequence.

Page 19

REPEATING SERIES OF KEY PRESSES USING THE AUD AND VID KEYS

The

A/V Producer

VID) that allow the user to play back a series of key strokes at any time with the press of one key. Each sequence can have up to a maximum of 15 keystrokes. These keys are not mode specific and can be accessed in any mode. For example, to set up a sequence that will turn on your devices and turn the devices to the proper inputs:

has two Macro keys (AUD and

3 When your macro sequence is

concluded, press ESC to save.

Whenever the sequence key is pressed, the Tuner will power ON, the TV will power ON and change the input to VIDEO 1 and then the Satellite will power ON.

Repeat these steps to then setup the other sequence key (either AUD or VID) to your needs .

HOW TO USE THE SHIFT KEY

1 Press and hold MAGIC until the

MENU-

display screen changes from

x 2

[DEVICE and the TIME] to [TIMED SEQ]. Press MENU -

twice until the display reads [CONFIGURE], then press SELECT. The display will then read [THEATR SEL].

2 Press MENU - four times until the

MENU-

x 4

display reads [KEY MACRO]. Press

SELECT. The display will read

[SEL MACKEY]. Press either the AUD or VID sequence key. This will be the key that will play back the series of keystrokes assigned to that

AUD

VID

key. The display will then read [SELECT SEQ]. Begin entering the sequence of keystrokes, up to 15, that you wish to be played back when you press either AUD or VID.

Note:

You cannot use either the

AUD

VID

keys in

your macro sequence.

For example:

(Sequence)

TUN + POWER + TV + POWER + TV/SAT (To change the input on the TV to VIDEO 1) + SAT + POWER.

Note:

When setting up your sequence, you will need to include any keystrokes that would normally be required during regular usage, such as pressing ENTER after entering a channel number when changing channels

The

A/V Producer

has features that can be accessed by using the SHIFT key. These features are listed above the key that they are mapped to. For example, on the transport keys (PLAY, REW, FF, STOP and PAUSE) there are the following features: SLOW, SLOW +, SLOW -, X2 and EJECT. These are accessed by pressing SHIFT and the key, for example, to eject a tape from your VCR press:

SHIFT + STOP

This will eject your tape, as long as your original remote supported this feature.

Note:

Once you have pressed the

SHIFT

key, the A/V Producer will remain in the "Shift" mode, indicated by an S on the LCD screen, for 10 seconds after the last key press or until the

SHIFT

key is pressed again.

The following keys have functions that are shifted:

CENTER: SHIFT + CENTER = REAR MENU: SHIFT + MENU = PROGRAM SELECT: SHIFT + SELECT = CLEAR MUTE: SHIFT + MUTE = SLEEP PREV CH: SHIFT + PREV CH = DISPLAY PIP: SHIFT + PIP = FREEZE PIP REW: SHIFT + REW = SLOWPLAY: SHIFT + PLAY = SLOW FF: SHIFT + FF = SLOW + STOP: SHIFT + STOP = EJECT PAUSE: SHIFT + PAUSE = X2

Important:

For a more detailed explanation of what function each shifted key performs by device type (TV, VCR, etc.), please refer to pages 45 through 57

Page 20

HOW TO USE THE SLEEP KEY

The

A/V Producer

operates your component’s sleep timer or, if your component does not have a sleep timer, it activates the

A/V Producer

A/V Producer’s

MUTE). If your component does not have a sleep timer, the

A/V Producer

activate the built-in sleep timer, press SLEEP (SHIFT + MUTE). The display will change to [SLEEP 15]. To add time to the sleep timer, press MENU -. Each press of MENU - will add 15 minutes to the sleep timer, up to a total of 60 minutes. Once the desired time is displayed on the LCD screen, press SELECT. The display screen will change to [SLEEP and the TIME].

has a SLEEP key that either

built-in sleep timer. To use the

SLEEP key, press SLEEP (SHIFT +

will access it’s own built-in timer. To

VOLUME LOCK

With the entertainment component controls your volume in the TV, VCR, CBL and SAT modes. When you originally set up the component operates it’s own volume, provided the component has volume control. You can change this setting so that one component controls the volume whether you are in the TV, VCR, CBL or SAT modes. For example, to set-up the

Producer

Amplifier in the TV, VCR, CBL and SAT modes: 1 Press and hold MAGIC until the

A/V Producer

, you can choose which home

A/V Producer

, each individual

A/V

to always control the volume through your

display screen changes from [DEVICE and the TIME] to [TIMED SEQ].

Sleep lock

If you would like the

A/V Producer

to use it’s built-in sleep timer on all of your components, you can lock the SLEEP mode. To set-up the

A/V Producer

to use

the internal sleep timer on all components:

1 Press and hold MAGIC until the

display screen changes from [DEVICE and the TIME] to [TIMED SEQ].

2 Press the MENU - key twice, the

MENU-

MENU+

x 2

display will change to [ CONFIGURE]. Press SELECT, the display will

change to [THEATR SEL]. Press MENU + two times, the display will read [SLEEP LOCK]. Press

x 2

SELECT, the display will change to

[DISABLE].

3 Press MENU - one time to change

the display to [ENABLE] then press SELECT. The display will return to [DEVICE and the TIME]. Now,

MENU-

whenever you press SLEEP (SHIFT + MUTE), the

A/V Producer

will use

it’s own built-in sleep timer.

Note: When using the built-in sleep timer, pressing POWER will cancel the sleep function.

2 Press the MENU - key twice, the

3 Press MENU - two times, the display

MENU-

x 2

display will change to

[CONFIGURE]. Press SELECT, the display will change to [THEATR SEL].

x 2

will read [VOL LOCK]. Press

SELECT, the display will change to

[UNLOCK].

4 Press MENU - one time to change

MENU-

(Device Key)

the display to [LOCK] then press SELECT. No w press the key for the component that will control your volume. In this example, to control the volume through your amplifier, press AMP. The display will return to [DEVICE and the TIME].

Now, when you use the volume keys on your

A/V Producer

, the volume will be controlled by the

specified component. To return volume control to each individual

component:

1 Press and hold MAGIC until the

display screen changes from [DEVICE and the TIME] to [TIMED SEQ].

Page 21

2 Press the MENU - key twice, the

3 Press MENU - two times, the display

MENU-

x 2

display will change to

[CONFIGURE]. Press SELECT, the display will change to [ THE AT R S EL].

x 2

will read [VOL LOCK]. Press

SELECT, the display will change to

[LOCK].

KEYMOVER

Keymover allows you to map features from one device mode to another. For example, if your VCR does not have volume control, you can map the volume keys in the TV mode to the VCR mode. This will allow you to control the volume of your TV while using your VCR. To Keymover features from one mode to another:

4 Press MENU - one time to change

the display to [UNLOCK] then press SELECT. The display will return to [DEVICE and the TIME].

MENU-

Now, when you use the volume keys on your

A/V Producer

, each component will control it’s own volume, as long as that component originally had volume control.

1 Press and hold MAGIC until the

display screen changes from [DEVICE and the TIME] to [TIMED SEQ].

2 Press the MENU - key twice, the

MENU-

MENU+

x 2

display will change to [ CONFIGURE]. Press SELECT, the display will

change to [THEATR SEL]. Press MENU + three times, the display will read [KEY MOVER]. Press

x 3

SELECT, the display will change to

(Device Key)

3 Press the device ke y (TV, VCR,

[FROM].

CBL, etc.) that contains the feature you want to move. For the example above, to move the TV’s volume, you would press TV. The display will show the device key that was just pressed.

4 Press the key for the feature you

L- VO

L+

want to move. For the example above, press VOL +. The displa y

(Device Key)

will change to [TO]. Press the device ke y (TV, VCR, CBL, etc.) where you would like to place the feature. For the example above, you would press VCR. The display will show the device key that was just pressed.

Page 22

5 Press the key where you want to

L- VO

L+

move the feature. For the example above, press VOL +. The displa y will return to [DEVICE and the TIME] . In the VCR mode, your

A/V Producer

will now operate volume up on your TV. Now, to complete the example above, repeat this sequence to move VOL - and MUTE from the TV mode to the VCR mode.

CLEAR ALL

If you would like to reset the advanced functions, use the CLEAR ALL feature. The CLEAR ALL feature will erase the following functions from the memory of the Macro Sequences, Timed Macro Sequences, Volume Lock and Keymovers. CLEAR ALL will not erase your set-up codes. To clear the memory using the CLEAR ALL feature:

1 Press and hold MAGIC until the

display screen changes from [DEVICE and the TIME] to [TIMED SEQ].

2 Press the MENU - key twice, the

MENU-

MENU+

x 2

display will change to [ CONFIGURE]. Press SELECT, the display will

change to [THEATR SEL]. Press MENU + one time, the display will read [CLEAR ALL]. Press SELECT, the display will change to [ CLR ALL].

3 Press SELECT, the display will

x 2

change to [CONFIRM]. Press SELECT once more and the display will return to [DEVICE and the TIME] . Your

A/V Producer

is now reset.

of all

TROUBLESHOOTING

Problem: Solution

LCD screen begins to fade, does not appear or the red light blinks five times when you press a key?

The

A/V Producer

does not operate your home entertainment component?

The

A/V Producer

not performing commands properly?

You make a mistake when setting up your

A/V Producer

Replace the batteries with four (4) new AAA alkaline batteries.

Try all of the codes listed for your brand of home entertainment component in the “Set-Up Codes” section. If this does not work, try searching for your code. Make sure the home

entertainment component you are setting up is able to be operated with an infrared remote control.

Try all of the codes listed for your brand of home entertainment component in the “Set-Up Codes” section. Many set-up codes may allow some degree of operation. However, only one set-up code will work correctly with your home entertainment component.

During any set up procedure, except for Macros and Timed Sequences, the ESC key will return you to the [DEVICE and the TIME] screen without saving. If you make a mistake when setting up a Timed Sequence, return to the Timed Sequence menu and delete the incorrect sequence. If you make a mistake when saving a Macro, erase the incorrect Macro by re-saving a new Macro on that key.

VCR not recording?

As a safety feature on the

A/V Producer

, you must

press the REC key twice.

Page 23

TROUBLESHOOTING (cont.)

WARRANTY

Problem: Solution

Channel +/- and PREV CH not working for your RCA TV?

Problems changing channels?

The red light blinks when you press a key but you receive no response from your home entertainment component?

Your audio components turn on and off and control the volume but does not change your preset channels?

Your DSS satellite receiver does not respond to the codes listed in the manual?

Due to RCA design (1983-

1987), only the original remote control will operate these functions.

If your original remote control required an ENTER keystroke when changing channels, press the ENTER key on the after you enter the channel number.

Make sure you are aiming your

A/V Producer

home entertainment component and that you are within 15 feet before using your remote.

Some audio components may need both a Tuner/ Receiver code and an Audio Amplifier code to control all of the features of your audio component.

The codes listed in the manual are set up to operate your DSS receiver on the 1st or 2nd addresses only. Make sure the DSS Receiver you are setting up is able to be operated with an infrared remote control and not set up to only receive Radio Frequency.

A/V Producer

at your

One For All PRODUCTS

Limited Warranty

Universal Electronics Inc. (“UEI”) warrants, to the original purchaser only , that this product will be free from def ects in materials and workmanship, under normal use, for ninety (90) days from the date of original purchase.

This warranty does not cover damage or f ailures caused by products or services not supplied by UEI, or which result from accident, misuse, abuse, neglect, mishandling, misapplication, faulty installation, set-up adjustment, improper maintenance, alteration, maladjustment of consumer controls, modifications, commercial use, or that is attributable to acts of God.

There are no express warranties except as listed above. UEI SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This w arranty gives y ou specific legal rights and you may also have other rights which vary from state to state.

To obtain warranty service for a defective product during the warranty period, please return the product, preferably in the original carton, along with your purchase receipt, to the store of original purchase. A note detailing the complaint would be helpful. The store, at its option, will replace or repair this product if found to be defective.

Universal Electronics Inc.

(330)-405-8655

The

A/V Producer

not operating your Bang & Olufsen equipment?

Some Bang & Olufsen

products, as well as some other manufacturer’s equipment operate at a frequency higher than 100 kHz and will not work with the

A/V Producer

Consumer Help Line: 1-330-405-8552 World Wide Web: http://www.oneforall.com

As you add new components to your home entertainment system, One For All has a remote control that will fit your needs. Look for these exciting products at a retailer near you.

One For All® and A/V Producer are trademarks of Universal Electronics Inc.

URC-8080 - 17 - REV - A A/V Producer McK M4057 2/98

One Forall URC 8080 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual