Your manual is divided into two parts: set-up instructions and device codes.
You may need this guide again in the future, so please be sure to
keep it.
Your ONE FOR ALL 2 needs 2 new “AA/LR6” alkaline batteries.
Your ONE FOR ALL 2 can operate two devices: a Television and a Video
Recorder.
About Your ONE FOR ALL 2
English
Televisions 11
Video Recorders 19
Page 3
WWW.ONEFORALL.COM3
1
9
7
4
5
6
10/11
8
3
2
Page 4
Installing the Batteries
Your ONE FOR ALL 2 needs 2 new “AA/LR6” alkaline batteries.
1Remove the battery cover from the back of your ONE FOR ALL 2 by
pressing down on the tab.
2Match the batteries to the + and - marks inside the battery case,
then insert the batteries.
3Press the battery cover back into place.
See picture of ONE FOR ALL 2 remote on page 3
1LED
The LED (Light Emitting Diode) flashes red to show the remote is
working.
2MAGIC Key
The MAGIC key is used to set up your ONE FOR ALL 2.
3MENU Key
The MENU key controls the same function as it did on your original
remote.
4POWER Key
The Power key controls the same function as it did on your original
remote.
5Device Keys
The TV and VCR keys select the device to be controlled. For example pressing the TV key allows the remote to control the functions of your Television and after pressing VCR you can operate
your Video Recorder.
6Number Keys
The Number keys (0-9, 10, 20 (AV)) provide functions just like your
original remote, such as direct access programme selection. If your
original remote uses one/two digit input switching (-/-- symbol), this
function can be obtained by pressing the -/-- key, which is the same
as the 10 key. If your original remote has an 20 key, this function can
also be found under the AV key.
7Programme (Channel) +/- Keys
These keys operate in the same way as the keys on your original
remote. If available on your original remote, these keys will allow
you to navigate through the menu.
The Keypad
Important notes:
- In order to avoid having to reprogram your ONE FOR ALL 2 after
you remove the batteries, you will need to insert new batteries
within 5 minutes. Also it is best that you do not use rechargable
batteries.
- On the inside of the battery compartment door you will find a
label on which to write your Set-Up codes after your ONE FOR
ALL 2 is set up for your device. Please write down your codes for
easy, future reference.
WWW.ONEFORALL.COM4
Page 5
WWW.ONEFORALL.COM5
8MUTE Key
The Mute key operates the same function it did on your orginal
remote control. Also, if your original remote control required that
you press an “OK” or “ENTER” key during Menu operation, the
Mute key can be used for this function.
9Volume +/- Keys
These keys operate in the same way as the keys on your original
remote. If available on your original remote, these keys will allow
you to navigate through the menu.
10Video Recorder Keys
After pressing the VCR key, the Video Recorder keys operate the
functions of your Video Recorder. To prevent accidental recording,
the Record key must be pressed twice to start recording.
11Teletext and Fastext Keys
After pressing the TV key, the top row of the VCR keys is used to
operate the main Teletext functions. The symbols below the keys are
for Teletext. The text keys are used to access the Teletext functions
of your television. Of course, your television must have Teletext
capability.
TEXT ON: Puts the television in the Teletext mode.
TEXT OFF: Switches the television back to regular viewing mode. On
some televisions, this may be done by pressing the TEXT ON key
several times.
HOLD/STOP: Stops changing pages.
EXPAND: Shows the top half of the Teletext page in larger letters.
By pressing again, you can see the bottom half of the Teletext page
enlarged. To return to regular Teletext viewing, press the EXPAND
key again, or press the TEXT ON key, depending on your television.
After pressing the TV key and accessing the text mode, the bottom row of
the Video Recorder keys marked
red, green, yellow and blue, allow you
to access the Fastext functions of your television. If on your original
remote control these keys are used for Menu navigation, the ONE
FOR ALL Fastext keys may operate in the same way.
Important note: For a more detailed explanation of Teletext and Fastext,
please refer to the manual of your television. Remember, different televisions
control Teletext and Fastext features in different ways. Not all of the Teletext
functions may be available for your particular model.
Page 6
6WWW.ONEFORALL.COM
3Press and hold down MAGIC until the red light blinks
twice. (The red light will blink once and then twice.)
4Enter your (four-digit device code) using the number
keys. The red light will blink twice.
5Now, aim the ONE FOR ALL 2 at your device and
press POWER If your device switches off, the ONE
FOR ALL 2 is ready to operate your device.
6
Turn your device back on and try all the remote’s functions to ensure
they are working properly. If the functions do not work properly,
repeat steps 1-5 using another code listed under your brand.
7If your device does not respond, follow steps 1 to 5 with
each code listed for your brand. If none of the codes listed
for your brand operate your device, or if your brand is not
listed at all, try the search method described on page 7.
8Write your code in the four boxes provided in the battery
compartment and on page 10 for easy future reference.
Setting up the ONE FOR ALL 2
Before you start, please read these instructions carefully
Important notes:
- Most TV’s do not switch on pressing the POWER key. Please try pressing a
“number” key or the “TV-text off” key to switch your TV back on.
- Some codes are quite similar. If your device does not respond or is not
functioning properly with one of the codes, try another code listed under
your brand.
- If your device’s original remote control does not have a POWER key, press
PLAY instead of POWER when setting up your device.
- Remember to press the correct device key before operating your device.
Only one device can be assigned to a device key. If your original remote
operates more than one device, you need to set up each device separately.
MAGIC
____
6WWW.ONEFORALL.COM
Devices can be found under the following keys:
Video Recorder
Television
VCRTV
Direct code set up
Example: To set up the ONE FOR ALL 2 for your television:
1
ONE FOR A
Acura
Admiral
Adyson
Agazi
AGB
Agef
Aiko
2Press the TV key
Find the code for your device in the Code list (page 11 - 22).
1
4
, 0
3
6
9
3
0
0
, 0
0
3
9
0
, 0
7
8
0
0
6
1
2
, 0
Codes are listed by device type and brand name.
7
1
2
0
4
6
2
0
6
1
5
0
, 0
7
3
7
0
8
0
, 0
0
9
0
0
, 0
6
1
2
The most popular code is listed first.
0
4
7
2
1
, 0
7
7
3
3
0
, 0
0
8
0
2
, 0
1
6
3
0
device is switched on (not on standby).
TV
on the ONE FOR ALL 2.
Make sure your
Page 7
The Search Method
If your device does not respond to the ONE FOR ALL 2 after you have tried
all the codes listed for your brand, try searching for your code. The Search
Method allows you to find the code for your device by scanning through all
the codes contained in the memory of the ONE FOR ALL 2. The Search
Method may also work if your brand is not listed at all.
Example: To search for your TV code:
1Switch your television on (not on standby).
2Press the TV key on your ONE FOR ALL 2.
3Press and hold down MAGIC until the ONE FOR ALL 2’s
red light blinks twice (The red light will blink once and
then twice).
4Press 9 9 1. The red light will blink twice.
5Next, press POWER.
6Aim the ONE FOR ALL 2 at your Television. Now press CH+
over and over, until your Television turns off (everytime
you press the CH+ key the ONE FOR ALL 2 will send out a
POWER signal from the next code contained in the memory). You may have to press this key many times (up to 150
times) so please be patient. If you skip past a code, you
can go to the previous code(s) by pressing the CH- key.
Remember to keep pointing the ONE FOR ALL 2 at your
Television while pressing this key.
7As soon as your television turns off, press MAGIC to store
the code.
Once you have Set-Up your ONE FOR ALL 2, you can blink back your
SET-UP CODE for future reference.
Example: To blink out your Television code:
1
Press TV once.
2Press and hold MAGIC until the ONE FOR ALL 2’s red
light blinks twice (The red light will blink once and then
twice).
3Press 9 9 0. The red light will blink twice.
4For the first digit of your four-digit code, press 1 and
count all the red blinks. If there are no blinks, the digit is
"0".
5For the second digit, press 2 and count all the red blinks.
If there are no blinks, the digit is "0".
6For the third digit, press 3 and count all the red blinks.
If there are no blinks, the digit is "0".
7For the fourth digit, press 4 and count
all the red blinks. If there are no blinks, the digit is "0".
Now you have your four-digit code.
Important notes:
- Most TV’s do not switch on pressing the POWER key. Please try pressing a
“number” key or the “TV-text off” key to switch your TV back on.
- To search for the code for your Video Recorder follow the instructions
above only press the VCR device key instead of TV during step 2.
- If your Video’s original remote control does not have a POWER key, press
PLAY instead of POWER during step 5.
WWW.ONEFORALL.COM7
MAGIC
MAGIC
MAGIC
9
919
9
0
1
2
3
4
TV
TV
Page 8
____
MAGIC
MAGIC
MAGIC
929
MAGIC
929
929
MAGIC
929
TV
VCR
VCR
TVTVTV
VCR
VCR
VCR
____
MAGIC
TV
8WWW.ONEFORALL.COM
It is possible to change the mode of any device key. This is useful if you
want to set up two of the same devices on the ONE FOR ALL 2. The code
can be set up using “Direct code set up” (p. 6) or “Search method” (p. 7).
To change a device key, see the three examples below.
Example 1) if you would like to program a second TV on the VCR key.
Example 2) if you would like to program a second VCR on the TV key.
Example 1:
To program a second Television on the VCR key (for example), you need
to change the VCR key into a TV key, so press:
(*)(**)
The VCR key has now become a second TV key.
Now enter the Set-Up code for your second TV by pressing:
(*) (TV code) (**)
Example 2:
To program a second Video Recorder on the TV key (for example), you
need to change the TV key into a VCR key, so press:
(*)(**)
The TV key has now become a second VCR key.
Now enter the Set-Up code for your second VCR by pressing:
(*) (VCR code) (**)
Resetting a Device key
Example: To reset the TV key to its original mode, press:
(*)(**)
Example: To reset the VCR key to its original mode, press:
(*)(**)
(*) Press and hold down the MAGIC key until the red light (LED)
blinks twice.
(**) The red light (LED) will blink once then twice.
Extra Features
Mode re-assignment
(Changing a device mode)
Page 9
WWW.ONEFORALL.COM9
Volume Punch Through
You may be able to use some functions of your Television, Video recorder
at the same time. For example: if you are watching a program on your
video recorder, you can adjust the volume (a TV function) without pressing
the TV mode key on your ONE FOR ALL 2. The table below lists some of the
possibilities.
Last Device Mode Key Pressed: You Can Control:
VCR TV volume up and down, mute
To punch through to TV volume while in the VCR mode:
1.
Press and hold MAGIC until the red light blinks
twice.
2.Press 9 9 3.
3.Then press the TV key and the red light will blink
twice.
To cancel the “Volume Punch Through” per mode:
(Example: to cancel the “Volume Punch Through” for the VCR mode)
1.Press VCR once.
2.Press and hold down the MAGIC key until the red
light blinks twice.
3.Press 9 9 3.
4.Then press the Volume (-) key and the red light will
blink four times.
Example: being in VCR mode, you will be able to control VOL+/- or MUTE
functions of your VCR (provided it has volume control).
To cancel the „Volume Punch Through“:
1.
Press and hold MAGIC until the red light blinks
twice.
2.Press 9 9 3.
3.Press the Volume (+) key and the red light will blink
four times.
Extra Features
MAGIC
MAGIC
MAGIC
TV
VCR
9
9
3
9
9
3
9
9
3
Page 10
10WWW.ONEFORALL.COM
Problem & Solution
Problem:
Your brand is not listed
in the code section?
The ONE FOR ALL does
not operate your
device(s)?
The ONE FOR ALL is not
performing commands
properly?
Problems changing
channels?
Video not recording?
The ONE FOR ALL does
not respond after
pressing a key?
The red light does not
blink when you press
a key?
Solution:
Try the search method on page 7.
A) Try all the codes listed for
your brand. B) Try the search
method on page 7.
You may be using the wrong
code. Try repeating the Direct
Set-Up using another code listed
under your brand or start the
search method over again to
locate the proper code.
Enter the programme number
exactly as you would on your
original remote.
As a safety feature on your ONE
FOR ALL, you must press the
Record key twice.
Make sure you are using new
batteries and are aiming the one
for all at your device.
Replace batteries with 2 fresh,
new “AA” alkaline batteries.
Quick Code Reference
Write down the codes for your devices in the boxes below and in
the battery compartment for quick and easy reference.