Your manual is divided into two parts: set-up instructions and device codes.
You may need this guide again in the future, so please be sure to
keep it.
Your ONE FOR ALL needs 2 new “AA/LR6” alkaline batteries.
Your ONE FOR ALL can operate a Television.
About Your ONE FOR ALL
English
Televisions 9
WWW.ONEFORALL.COM3
1
9
7
4
5
6
10
8
3
2
Installing the Batteries
Your ONE FOR ALL needs 2 new “AA/LR6” alkaline batteries.
1Remove the battery cover from the back of your ONE FOR ALL by
pressing down on the tab.
2Match the batteries to the + and - marks inside the battery case,
then insert the batteries.
3Press the battery cover back into place.
See picture of ONE FOR ALL TV remote on page 3
1LED
The LED (Light Emitting Diode) flashes red to show the remote is
working.
2MAGIC Key
The MAGIC key is used to set up your ONE FOR ALL.
3MENU Key
The MENU key controls the same function as it did on your original
remote.
4POWER Key
The Power key controls the same function as it did on your original
remote.
5Device Key
Pressing the TV key allows the remote to control the functions
of your Television.
6Number Keys
The Number keys (0-9, 10, 20 (AV)) provide functions just like your
original remote, such as direct access programme selection. If your
original remote uses one/two digit input switching (-/-- symbol), this
function can be obtained by pressing the -/-- key, which is the same
as the 10 key. If your original remote has an 20 key, this function can
also be found under the AV key.
7Programme (Channel) +/- Keys
These keys operate in the same way as the keys on your original
remote. If available on your original remote, these keys will allow
you to navigate through the menu.
The Keypad
Important notes:
- In order to avoid having to reprogram your ONE FOR ALL after
you remove the batteries, you will need to insert new batteries
within 5 minutes. Also it is best that you do not use rechargable
batteries.
- On the inside of the battery compartment door you will find a
label on which to write your Set-Up code after your ONE FOR ALL
is set up for your device. Please write down your code for easy,
future reference.
WWW.ONEFORALL.COM4
WWW.ONEFORALL.COM5
8MUTE Key
The Mute key operates the same function it did on your orginal
remote control. Also, if your original remote control required that
you press an “OK” or “ENTER” key during Menu operation, the
Mute key can be used for this function.
9Volume +/- Keys
These keys operate in the same way as the keys on your original
remote. If available on your original remote, these keys will allow
you to navigate through the menu.
10Teletext and Fastext Keys
The text keys are used to access the Teletext functions of your
television. Of course, your television must have Teletext capability.
TEXT ON: Puts the television in the Teletext mode.
TEXT OFF: Switches the television back to regular viewing mode. On
some televisions, this may be done by pressing the TEXT ON key
several times.
HOLD/STOP: Stops changing pages.
EXPAND: Shows the top half of the Teletext page in larger letters.
By pressing again, you can see the bottom half of the Teletext page
enlarged. To return to regular Teletext viewing, press the EXPAND
key again, or press the TEXT ON key, depending on your television.
After accessing the text mode, the bottom row of the keys marked
red,
green, yellow and blue, allow you to access the Fastext
functions of your television.
If on your original remote control these
keys are used for Menu navigation, the ONE FOR ALL Fastext keys
may operate in the same way.
Important note: For a more detailed explanation of Teletext and Fastext,
please refer to the manual of your television. Remember, different televisions
control Teletext and Fastext features in different ways. Not all of the Teletext
functions may be available for your particular model.
6WWW.ONEFORALL.COM
3Press and hold down MAGIC until the red light blinks
twice. (The red light will blink once and then twice.)
4Enter your (four-digit device code) using the number
keys. The red light will blink twice.
5Now, aim the ONE FOR ALL at your device and
press POWER. If your device switches off, the ONE
FOR ALL is ready to operate your device.
6
Turn your device back on and try all the remote’s functions to ensure
they are working properly. If the functions do not work properly,
repeat steps 1-5 using another code listed under your brand.
7If your device does not respond, follow steps 1 to 5 with
each code listed for your brand. If none of the codes listed
for your brand operate your device, or if your brand is not
listed at all, try the search method described on page 7.
8Write your code in the four boxes provided in the battery
compartment and on page 8 for easy future reference.
Setting up the ONE FOR ALL
Before you start, please read these instructions carefully
Important notes:
- Most TV’s do not switch on pressing the POWER key. Please try pressing a
“number” key or the “TV-text off” key to switch your TV back on.
- Some codes are quite similar. If your device does not respond or is not
functioning properly with one of the codes, try another code listed under
your brand.
MAGIC
____
6WWW.ONEFORALL.COM
Direct code set up
To set up the ONE FOR ALL for your television:
1
ONE FOR A
Acura
Admiral
Adyson
Agazi
AGB
Agef
Aiko
TV
2Press the TV key
Find the code for your device in the Code list (page 9 - 17).
1
4
, 0
3
6
9
3
0
0
, 0
0
3
9
0
, 0
7
8
0
0
6
1
2
, 0
Codes are listed by brand name.
7
1
2
0
4
6
2
0
6
1
5
0
, 0
7
3
7
0
8
0
, 0
0
9
0
0
, 0
6
1
2
The most popular code is listed first.
0
4
7
2
1
, 0
7
7
3
3
0
, 0
0
8
0
2
, 0
1
6
3
0
device is switched on (not on standby).
Make sure your
on the ONE FOR ALL
WWW.ONEFORALL.COM7
Search Method
If your device does not respond to the ONE FOR ALL after you have tried
all the codes listed for your brand, try searching for your code. The Search
Method allows you to find the code for your device by scanning through all
the codes contained in the memory of the ONE FOR ALL. The Search
Method may also work if your brand is not listed at all.
To search for your TV code:
1
Switch your television on (not on standby).
2Press the TV key on your ONE FOR ALL.
3Press and hold down MAGIC until the red light blinks
twice (The red light will blink once and then twice).
4Press 9 9 1. The red light will blink twice.
5Next, press POWER.
6Aim the ONE FOR ALL at your Television. Now press CH+
over and over, until your Television turns off (everytime
you press the CH+ key the ONE FOR ALL will send out a
POWER signal from the next code contained in the memory). You may have to press this key many times (up to 150
times) so please be patient. If you skip past a code, you
can go to the previous code(s) by pressing the CH- key.
Remember to keep pointing the ONE FOR ALL at your
Television while pressing this key.
7As soon as your television turns off, press MAGIC to store
the code.
Once you have Set-Up your ONE FOR ALL, you can blink back your
SET-UP CODE for future reference.
Example: To blink out your Television code:
1
Press TV once.
2Press and hold MAGIC until the red light blinks twice
(The red light will blink once and then twice).
3Press 9 9 0. The red light will blink twice.
4For the first digit of your four-digit code, press 1 and
count all the red blinks. If there are no blinks, the digit is
"0".
5For the second digit, press 2 and count all the red blinks.
If there are no blinks, the digit is "0".
6For the third digit, press 3 and count all the red blinks.
If there are no blinks, the digit is "0".
7For the fourth digit, press 4 and count
all the red blinks. If there are no blinks, the digit is "0".
Now you have your four-digit code.
MAGIC
MAGIC
MAGIC
TV
9
9
1
9
9
0
1
2
3
4
TV
TV
Important note:
- Most TV’s do not switch on pressing the POWER key. Please try pressing a
“number” key or the “TV-text off” key to switch your TV back on.
Problem & Solution
Problem:
Your brand is not listed
in the code section?
The ONE FOR ALL does
not operate your
device ?
The ONE FOR ALL is not
performing commands
properly?
Problems changing
channels?
The ONE FOR ALL does
not respond after
pressing a key?
The red light does not
blink when you press
a key?
Solution:
Try the search method on page 7.
A) Try all the codes listed for
your brand. B) Try the search
method on page 7.
You may be using the wrong
code. Try repeating the Direct
Set-Up using another code listed
under your brand or start the
search method over again to
locate the proper code.
Enter the programme number
exactly as you would on your
original remote.
Make sure you are using new
batteries and are aiming the one
for all at your device.
Replace batteries with 2 fresh,
new “AA” alkaline batteries.
8WWW.ONEFORALL.COM
Quick Code Reference
Write down the code for your device in the boxes below and in the
battery compartment for quick and easy reference.