One for All URC 3300 User Manual
3 DEVICES
UNIVERSAL REMOTE CONTROL
USER’S GUIDE
INTRODUCTION
The One For All 3 Devices Universal
Remote Control is designed to operate
three home entertainment devices,
depending on the model purchased (see
Key Charts,Mode Keyson the right).
The remote control requires four fresh
AAA alkaline batteries (not included) and
easy programming to co ntrol yo ur d evices.
For best results,please read and perform
all instructions listed here.Also,keep
these instructions for future reference.
FEATURES AND FUNCTIONS
Use the Key Chartsto learn how to use the
universal functions ofthe One For All 3
Devices Universal Remote Control.
Key Charts
Use SET for all
programming
sequences.
The LED (red light)
blinks to show that
the remote control is
working and is
sending signals.
Press POWER once to
turn on or off the
selected device.
Mode Keys for 3 Devices:
Press VCR/DVD,TV,or
CBL/SATonce to sele ct
a home entertainment
device to control.
Use the keypad (0~9)
to directly select
channels (for example,
09 or 31).
Press MUTE once to
turn sound off
or on.
Press PREV CH once to
recall the last-viewed
channel and to page
back one screen on the
main menu.
Press ENTER once
after entering channel
numbers on some TV
models.
Use MENU (or EXIT) to
choose options (or
exit) from your
selected device’s
menu or guide.
Use VOL+(or VOL-)
to raise (or lower) the
sound volume.
Use CH+ (or CH -) to
select the next higher
(or lower) channel.
When co ntrolli ng a
DVD player,use SKIP
FORWARDto next DVD
chapter.,use SKIP
REVERSE to the l ast
DVD chapter.
Press SHIFT and use
the Up/Down/Left
Right cursor keys to
move the cursor in the
program guide and
menu screens.
Press SHIFT and MUTE
to select a m enu item.
Press SLEEP to activate
your device’s sleep
timer (not available
for all devices).
Use the transport keys
to control your VCR,
CD or DVD player,or
VOD. To record a
program, press the
record key (
twice.
use TV/VID to switch
the TV’s input to view
TV or video program.
REC
)
INSTALLING BATTERIES
1. On the remote control’ s back,push the
tab and lift offthe battery cover.
2. Obtain four (4) new AAA al kaline
batteries.Match the + and – marks
on the batteries to the + and –
marks in the battery case,then insert
the new batteries.
3. Press the battery cover back into
place.The tab should click when the
cover is locked.
4. Test the unit by pressing POWER
and any mode key (e.g.,TV).Ifthe
batteries are inserted correctly,the
LED will blink once.
NOTE:When batteries need replacement,
the remote control will stop operating.
Remove the old batteries and insert new
ones within 30 minutes to ensure all of
your programming information is restored.
PROGRAMMING
DEVICE CONTROL
The One For All 3 Devices remote control is preprogrammed at the factory to
operate an RCA TV and VCR,a Motorola
(GI) cable box,and a Toshiba DVD player.To control devices other than the
default brands,p er form the following
steps;otherwise skip this section:
NOTE:For TV/VCR Combo control, see the
next section.
1. Turn on a device (e.g.,VCR) and, if
applicable, insert media, (e.g.,
cassette or disc).
NOTE:Please read step s 2-4 completely
before proceeding.Highlight or write down
the codes and device you wish to program
before moving on to step 2.
2. On the remote control,pres s a device
key once (i.e., VCR/DVD,TV,or
CBL/SAT).Press and hold SETuntil
the LED blinks twice,then release
SET.
3. Use the Manufacturer’s Codes to
locate the type of device and brand
name and then enter the first fourdigit code for your component.If
performed correctly,the LED will
blink twice.
NOTE:Ifthe LED did not blink twice,then
repeat steps 2 through 3 and try entering
the same code again.
4. Aim the remote control at the device
and press POWERonce.The device
should turn off.If it does not respond,
repeat steps 2-3,try i ng each code for
your brand until you find one that
works.Ifit still does not work,tr y
Searching For Your Code.
NOTE:If the dev i ce do es not have a
POWER
key,press the (
5. Repeat steps 1 through 4 for each
device you want to control.
PLAY
) key.
PROGRAMMING
TV/VCR COMBO CONTROL
Perform the following instructions to
control a TV/VCR Combo:
1. Turn on the TV/VCR Combo and
insert a video cassette.
NOTE:Please read steps 2-4 completely
before proceeding.Highlight or write down
the codes and device you wish to program
before moving on to step 2.
2. On the remote control,press VCR/DVD.
Press and hold SETuntil the LED
blinks twice,then release SET.
3. Use the Setup Codes For TV/VCR
Combos (on the back side) to locate
the brand name and then enter the
first four-digit code for your device.
Ifperformed correctly,the LED wil l
blink twice.
NOTE:Ifthe LED did not blink twice,then
repeat steps 2 through 3 and try entering
the same code again.
4. Aim the remote control at the device
and press POWERonce.It should turn
off.Ifthe device does not respond,
repeat steps 2-3,try i ng each code for
your brand until you find one that
works.Ifit still does not work,tr y
Searching For Your Code.
NOTE:If the dev i ce do es not have a
POWER
key,press the (
PLAY
) key.
SEARCHING FOR YOUR CODE
Ifyour device does not respond to the
remote control after trying all codes
listed for your brand,or ifyour brand is
not listed at all,try searching for your
code. For example,to search for a code
for your TV:
1. On the remote control, press TV once.
2. Press and hold SET until the LED
blinks twice,then release SET.
3. Enter9 - 9 - 1.The LED will
blink twice.
4. Aim the remote control at the the
TV and slowly alternate between
pressing POWER and TV.Stop when
the TV turns off.
NOTE:In the search mode,the remote
control will send IR codes from its library
to the selected device,starting with the
most popular code first.
5. To lock in the code,press and hold
SET until the LED blinks twice,then
release SET.
6. To search for the codes ofyour other
devices,repeat steps 1 through 5,but
substitute the appropriate device key
for the device you are searching for.
CHECKING THE CODES
Ifyou have set up the remote control
using the Searching For Your Code
procedure,you may need to find out
which four-digit code is op erating your
equipment:
For example,to find out which code is
operating your TV:
1. On the remote control, press TV once.
2. Press and hold SET until the LED
blinks twice,then release SET.
3. Enter9 - 9 - 0.The LED will
blink twice.
4. To view the code for the first digit,
press 1 once.Wait 3 seconds,count
the LED blinks (e.g.,3 blinks =3)
and write down the number.
NOTE:Ifa code digit is “0”,the LED will
not blink.
5. Repeat step 4 three more times for
remaining digits.Use 2for the
second digit,3for the third digit,
and 4for the fourth digit.
6. To check for codes of other devices,
repeat steps 1 through 5,but substitute the appropriate device key for
each device you are checki ng .
As before,write down each fourdigit code.
RE-ASSIGNING DEVICE KEYS
The One For All 3 Devices can be set to
control a second TV,VCR,or DVD player.
For example,to control two TVs,a VCR,
and a cable box,you will need to reassign the unused VCR/DVDke y to ope rate the second TV as follows:
1. On the remote control,press and
hold SET until the LED blinks twice,
then release SET.
2. Enter 9- 9- 2.The LED will
blink twice.
3. Press TVonce,then press VCR/DVD
once.
4. The VCR/DVDkey is now ready to be
programmed for your second TV.
See Programming Device Cont rol.
To re-assign other device keys, repeat
steps 1 through 4 by substituting the key
sequence from the below chart for the
most popular components:
To Re-Assign Key
Sequence Perform
VCR/DVD as 2nd TV key: SET- 9 - 9- 2-
TV - VCR/DVD
VCR/DVD as 2nd CBL key: SET- 9 - 9 - 2-
CBL/SAT VCR/DVD
VCR/DVD as 2nd SAT k ey: SET - 9 - 9 - 2 -
CBL/SAT VCR/DVD
VCR/DVD back to VCR/DVD:SET - 9 - 9- 2 -
When a re-assignment is done,the LED
will blink twice to confirm your choice.
At that time,you will need to program
the remote control for the new device
(see Programming Device Control).
VCR/DVD VCR/DVD
CHANGING VOLUME LOCK
The One For All 3 Devices is set to
control the volume ofyour TV in the TV,
VCR, CBL/SAT,and DVD modes.If you
want the volume to be controlled by a
mode other than TV (e.g.,CBL/SAT),
change the Volume Lock as follows:
To Change Volume Lock To
Another Mode:
1. On the remote control,press and
hold SET until the LED blinks twice,
then release SET.
2. Enter 9- 9 - 3 and then press any
mode key once (except TV).The LED
will blink twice.
3. Now,whenever you press VOL+,
VOL–,or MUTE,volume will be
controlled by your mode choice.
Unlocking Volume Control:
NOTE:Perform these instructions when you
want independent volume control for each
programmed device (e.g., TV volume control
in TV mode,CBL/SAT volume control in
CBL/SAT mode, etc.)
1. On the remote control,press and
hold SET until the LED blinks twice,
then release SET.
2. Enter 9- 9 - 3 and then press VOL+.
The LED will blink four times.
3. Volume will again be controlled
according to its default states.
TROUBLESHOOTING
For assistance, please contact us in any
ofthe following ways:
• Consumer Help Line:(330) 405-8612
• Internet: http://www.o nef o rall.c o m
PROBLEM: LED does not blink when
SOLUTION: Replace batteries with
PROBLEM: LED blinks when you
SOLUTION: Make sure the remote
you press a key.
AAA
four new
batteries.
press a key,but home
entertainment component
does not respond.
control is aimed at your
home entertainment
device and is not farther
than 15feet away.
alkaline
PROBLEM: The unit does not control
SOLUTION: Try all listed codes for the
PROBLEM: TV/VCR combo does not
SOLUTION: Use the VCR codes for
PROBLEM: Changing channels does
SOLUTION: Iforiginal remote control
PROBLEM: T ried “Searc h Method”
SOLUTION: Clear the device key as
PROBLEM: CH
SOLUTION: Due to RCA design (1983-
PROBLEM: Remote control does not
SOLUTION: For power on,these prod-
home entertainment
devices or commands are
not working properly.
component brands being
set up.Make sure they
can b e operated with an
infrared remote cont rol.
respond properly.
your brand.Some combo
units may require both a
TV code and a VCR code
for full operatio n.
not work properly.
required pressing ENTER
to change channels,press
ENTER on the remote
control after enter ing the
channel number.
and still could not find a
working code.
follows: Press and hold
SET until the LED
blinks twice,then release.
Next enter 9- 9- 2.Then
press the device key to be
cleared twice.Now repeat
the “Search Method. ”
▲and CH▼ do not
work for your RCA TV.
1987),only the original
remote control will operate these functions.
turn on Sony or Sharp
TV/VCR Combo.
ucts require programming
TV codes.For Sony, use
TV code 0000 and VCR
code 0032.For Sharp,use
TV code 0093 and VCR
code 0048.
LIFETIME WARRANTY
One For ALL ("OFA") warrants this
product to be free from defects in materials and workmanship, under normal
use,throughout the period ofthe product’s ownership by the original purchaser.This warranty does not cover damage
or failures caused by products or services not supplied by OFA,or which
result from accident,misuses,abuse,
neglect,mishandling,misapplication,
faulty installation,set-up adjustment,
improper maintenance,alteration,maladjustment of consumer cont rols,modifications,commercial use,or that is
attributable to acts ofGod.
There are no express warranties except
as listed above.OFA SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT
OR ARISING OUT OF ANY BREACH OF
WARRANTY,ALL EXPRESS AND
IMPLIED WARRANTIES,INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE,ARE LIMITED TO THE WARRANTY PERIOD SET
FORTH ABOVE.Some states do not
allow the exclusion or limitation of incidental or consequential damagers,or
limitations on how long an implied warranty lasts,so the above exclusions or
limitations may not apply to you.This
warranty gives you specific legal rights
and you may also have other rights
which vary from state to state.
To obtain warranty service for a defective product,please return the product,
preferably in the original carton,along
with your purchase receipt,to the store
oforiginal purchase for the first 90 days.
A note detailing the complaint would be
helpful.The store,at its option,will
replace or repair this product if found to
be defective.
Ifthe unit has been purchased more
than 90 days ago,pls return it to Impact
Distribution Services,6262 Patterson
Pass Road,Suite C,Livermore,CA 94550
together with the original receipt and
$3.95 to cover postage and handling.It
will be repaired or replaced at the ma n ufacturer’s option.The manufacturer
reserves the right to substitute a currently manufactured model with equal or
superior features.
ADDITIONAL INFORMATION
ONE FOR ALL® is the re gistered trademark ofUniversal Electronics Inc.
Computime International Ltd.is the
Licensee ofthe ONE FOR ALL® brand
for USA and Canada.
Copyright 2001 by Universal Electronics
Inc.No part of this publication may be
reproduc ed,transmitted,transcribed,
stored in any retrieval system,or translated to any language,in any form or by
any means,electronic,mechanical,magnetic,optical,manual,or otherwise,
without the prior written permission of
Universal E lectronics Inc.
One For All® 3 Devices is compatibile fo r
use in North America excluding Me xico.
URC-3300N/3330 12/01
Loading...