Omron Smart Sensor ZFX-C User Manual
Cat. No. Z264-E1-06A
Cat. No. Z264-E1-06A Smart Sensor ZFX-C USER´S MANUAL
Smart Sensor
ZFX-C
Vision Sensor
with built-in LCD monitor
USERS MANUAL
Introduction
Thank you for purchasing the ZFX-C.
This manual provides information regarding functions, performance and operating methods that
are required for using the ZFX-C.
When using the ZFX-C, be sure to observe the following:
• The ZFX-C must be operated by personnel knowledgeable in electrical engineering.
• To ensure correct use, please read this manual thoroughly to deepen your understanding of the
product.
• Please keep this manual in a safe place so that it can be referred to whenever necessary.
Manuals Provided with this Product
User's Manual (this document)
This manual describes basic operations, such as
installation and connections, and information on settings
and specifications to ensure safe and correct use of this
product.
Serial Communication Command
Reference
This manual provides reference information for when this
product performs communications with an external
device, such as a PC or a programmable controller, via
the serial interface.
Serial Communication
Command Reference
Cat. No.
XXXX-XX-XX
Smart Sensor
Vision Sensor with built-in LCD monitor
ZFX-C
User's Manual
Cat. No.
XXXX-XX-XX
Smart Sensor
Vision Sensor with built-in LCD monitor
ZFX-C
1
1
2
3
4
5
6
7
User's Manual
APPLICATION CONSIDERATIONS
(Please Read)
BEFORE USE
BASIC OPERATIONS
SETTING THE MEASUREMENT
CONDITIONS
FUNCTIONS USED DURING OPERATION
ADDITIONAL FUNCTIONS
PARALLEL INTERFACE
APPENDICES
Smart Sensor
Vision Sensor with built-in LCD monitor
ZFX-C
2
ZFX-C User’s Manual
READ AND UNDERSTAND THIS DOCUMENT
Please read and understand this document before using the products. Please consult your OMRON
representative if you have any questions or comments.
WARRANTY
OMRON’s exclusive warranty is that the products are free from defects in materials and workmanship for a
period of one year (or other period if specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NONINFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS.
ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT
THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON
DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.
In no event shall responsibility of OMRON for any act exceed the individual price of the product on which
liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS
REGARDING THE PRODUCTS UNLESS OMRON’S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE
PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO
CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
SUITABILITY FOR USE
THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT SAFETY RATED. THEY ARE NOT DESIGNED OR
RATED FOR ENSURING SAFETY OF PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES.
Please refer to separate catalogs for OMRON’s safety rated products.
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the
combination of products in the customer’s application or use of the product.
At the customer’s request, OMRON will provide applicable third party certification documents identifying ratings
and limitations of use that apply to the products. This information by itself is not sufficient for a complete
determination of the suitability of the products in combination with the end product, machine, system, or other
application or use.
The following are some examples of applications for which particular attention must be given. This is not
intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses
listed may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or
uses not described in this document.
ZFX-C User’s Manual
3
• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical
equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry
or government regulations.
• Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR
PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR
THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PERFORMANCE DATA
Performance data given in this document is provided as a guide for the user in determining suitability and does
not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate
it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of
Liability.
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other
reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant
construction changes are made. However, some specifications of the product may be changed without any
notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your
application on your request. Please consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when
tolerances are shown.
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed to be accurate; however, no
responsibility is assumed for clerical, typographical, or proofreading errors, or omissions.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user’s programming of a programmable product, or any consequence
thereof.
COPYRIGHT AND COPY PERMISSION
This document shall not be copied for sales or promotions without permission.
This document is protected by copyright and is intended solely for use in conjunction with the product. Please
notify us before copying or reproducing this document in any manner, for any other purpose. If copying or
transmitting this document to another, please copy or transmit it in its entirety.
4
ZFX-C User’s Manual
The following signal words are used in this manual.
The following alert symbols are used in this manual
Meanings of Signal Words
Indicates a potentially hazardous situation which, if not avoided, will result in minor or
moderate injury, or may result in serious injury or death. Additionally there may be
significant property damage.
Meanings of Alert Symbols
Indicates general prohibitions for which there is no specific symbol.
Indicates the possibility of laser radiation.
Indicates the possibility of explosion under specific conditions.
This product is not designed or rated for ensuring safety of persons.
Do not use it for such purposes.
The camera with lighting emits visible light, which may adversely affect the eyes in rare instances.
Do not look directly into the light emitted from the Camera. When the subject is a specular
reflective object, protect your eyes from reflected light.
A lithium battery is built into the Controller and may occasionally combust, explode, or burn if
not treated properly.
Dispose of the Controller as industrial waste, and never disassemble, apply pressure that
would deform, heat to 100 °C or higher, or incinerate the Controller.
ZFX-C User’s Manual
5
The following points are important to ensure safety, so make sure that they are strictly observed.
1.Installation Environment
• Do not use the product in environments where it can be exposed to inflammable/explosive gas.
• To secure the safety of operation and maintenance, do not install the product close to high-voltage devices
and power devices.
• Install the product in such a way that its ventilation holes are not blocked.
• Tighten mounting screws at the torque specified in this manual.
2.Power Supply and Wiring
• The voltage and AC power supply must be within the rated range (24 VDC ±10%).
• Reverse connection of the power supply is not allowed.
• Use the power supply within the rated load.
• High-voltage lines and power lines must be wired separately from this product. Wiring them together or
placing them in the same duct may cause induction, resulting in malfunction or damage.
• Use the product within the power supply voltage specified in this manual.
• Use a DC power supply with safety measures against high-voltage spikes (safety extra low-voltage circuits
on the secondary side).
• Tighten mounting screws at the torque specified in this manual.
3.Other
• Do not use this product in safety circuits associated with nuclear power and human life.
• Do not disassemble, repair, modify, deform by pressure, or incinerate this product.
• Dispose of this product as industrial waste.
• Connect the exclusive devices (Camera, Controller, Strobe Controller, Cable). The product might break
down or malfunction if you use a part not included in the exclusive products.
• Should you notice any abnormalities, immediately stop use, turn OFF the power supply, and contact your
OMRON representative.
4.Laws and Regulations, Standards
• This product complies with the following EC and EN directives:
EC Directive No.2004/108/EC
EN Standards EN61326
Precautions for Safe Use
6
ZFX-C User’s Manual
Observe the following precautions to prevent failure to operate, malfunctions, or undesirable effects on product
performance.
1.Installation Site
Do not install this product in locations subjected to the following conditions:
• Ambient temperature outside the rating
• Rapid temperature fluctuations (causing condensation)
• Relative humidity outside the range of 35 to 85%
• Direct vibration or shock
• Reflection of intense light (such as other laser beams, electric arc-welding machines, or ultra-violet light)
• Direct sunlight or near heaters
• Strong magnetic or electric field
Also, do not install this product in locations subjected to the following conditions to ensure its protective
performance as described in the specifications:
• Presence of corrosive or flammable gases
• Presence of dust, salt, or iron particles
• Water, oil, or chemical fumes or spray, or mist atmospheres
2.Power Supply and Wiring
• When using a commercially available switching regulator, make sure that the FG terminal is grounded.
• If surge currents are present in the power lines, connect surge absorbers that suit the operating
environment.
• Before turning ON the power after the product is connected, make sure that the power supply voltage is
correct, there are no incorrect connections (e.g. load short-circuit) and the load current is appropriate.
Incorrect wiring may result in breakdown of the product.
• Before connecting/disconnecting cables, make sure that the product is turned OFF. The product may break
down if it is connected/disconnected while the power is ON.
• For cables, use only the exclusive products specified in this manual.
p.14, p.15
• Use only combinations of the Camera, Controller and Strobe Controller specified in this manual. Using other
combinations may cause malfunction or damage.
• Do not turn the power OFF in the following instances. Doing so will damage data that is in the process of
being saved.
- While data is being saved on the Controller
- While data is being saved on the SD card
• The LCD panel has been made using precision technology, and sometimes a few pixels are missing in the
panel. This is due to the structure of the LCD panel, and is not a malfunction.
• Do not remove the base from the Camera.
3.Maintenance and Inspection
Do not use thinner, benzene, acetone or kerosene to clean the Camera and Controller. If large dust particles
adhere to the Camera, use a blower brush (used to clean camera lenses) to blow them off. Do not use breath
from your mouth to blow the dust off. To remove dust particles from the Camera, wipe gently with a soft cloth
(for cleaning lenses) moistened with a small amount of alcohol. Do not use excessive force to wipe off dust
particles. Scratches to the Camera might cause error.
4.Ventilation Film
• Do not peel of the ventilation film or prod it with a sharp-pointed object. This might impair its protective
structure.
• Do not cover the ventilation film. Doing so might cause the Camera's front panel to cloud.
Precautions for Correct Use
ZFX-C User’s Manual
7
5.Optional Lighting Connector
When the optional lighting is not connected, be sure to attach the connector cap. Otherwise, its protective
structure might be impaired.
6.Camera's Connector Cap
When using only one camera, attach the connector cap to cameras that are not in use.
7.Communication with a Host Device
Before communicating with a host device, make sure that the product has started up.
Also, clear the receive buffers on the device in use or perform other measures since undetermined signals
might be output from the host interface when this product is started up.
8
ZFX-C User’s Manual
Editor's Note
■ Meaning of Symbols
Menu items that are displayed on the Controller's LCD screen, and windows, dialog boxes and other GUI
elements displayed on the PC are indicated enclosed by brackets "[ ]".
■ Visual Aids
■ Difference between the ZFX-C20/C25, ZFX-C10H/C15H and ZFX-C10/C15
This manual is intended for the ZFX-C20/C25, ZFX-C10H/C15H and ZFX-C10/C15 Controllers.
Unless otherwise specified, explanations are given for the ZFX-C20/C25. The following table summarizes the
main differences.
Indicates points that are important to achieve the full product performance,
such as operational precautions.
Indicates application procedures.
Indicates pages where related information can be found.
Item ZFX-C20/C25 ZFX-C10H/C15H ZFX-C10/C15
Number of connected cameras 2 1 1
Available measurement items All available Only the following items are available:
Pattern search
Sensitive search
Area
Position
Width
Count
Angle
Bright
Hue
Defect
Available position correction items All available Only the following items are available:
Edge position
Area
1 model
2 model
Angle
Number of measurement items that
can be measured simultaneously
Max. 128 items/bank Max. 32 items/bank
Logging monitor function Available Not available
Important
Note
ZFX-C User’s Manual
9
CONTENTS
CONTENTS
1.BEFORE USE
ZFX-C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
System Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Mounting and Connecting Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installing Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installing the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connecting Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Overview of Settings and Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Operation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Outline of MENU mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Measurement Items and Banks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Initializing Controller Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Saving Setup Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.BASIC OPERATIONS
Inspection Setup and Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Setting Measurement Conditions - MENU Mode . . . . . . . . . . . . . . . . . . . . . . . . . 38
Checking the Measurement Status - ADJ Mode . . . . . . . . . . . . . . . . . . . . . . . . . 42
Starting Measurement - RUN Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Clear Images Cannot be Obtained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Measurement Target Cannot be Measured Accurately Due to Movement . . . . . 43
To Output Measurement Values to a PC or PLC . . . . . . . . . . . . . . . . . . . . . . . . . 44
To Output Position Information of Measurement Targets as Actual Coordinates 44
10
ZFX-C User’s Manual
3.SETTING THE MEASUREMENT CONDITIONS
Setting Measurement Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Shape Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Pattern Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Graphic Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Flexible Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Sensitive Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Size Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Edge Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Bright/Color Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Bright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
HUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Inspection by Individual Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Grouping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Defect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Image Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Cameras/Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Shutter Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Gain Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Partial Function Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Image Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Light Control (Recipe Functions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Registering Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Position Correction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Additional Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Setting Reflection of Individual Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Logging Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
4.FUNCTIONS USED DURING OPERATION
Monitoring the Measurement Status - RUN Mode . . . . . . . . . . . . . . . . . 124
Displaying Measurement Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Switching the Image Display Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Checking/Adjusting the Measurement - ADJ Mode . . . . . . . . . . . . . . . . 127
Checking Measurement Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Switching the Image Display Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Using a Saved Image to Perform Re-measurement . . . . . . . . . . . . . . . . . . . . . 129
Adjusting Measurement Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
ZFX-C User’s Manual
11
CONTENTS
5.ADDITIONAL FUNCTIONS
Bank Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Bank Data Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Bank Group Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Camera Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Communication Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Output Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Operation Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Measurement Control Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Operation Conditions during Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Setting/Changing the Display Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Setting/Changing the Date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Clearing Saved Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Saving/Loading Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
SD Card Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Checking Density Distribution (Profile) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Checking the Communication Status with External Devices . . . . . . . . . . . . . . . 152
Displaying the Controller Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
6.PARALLEL INTERFACE
Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Parallel Connector Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Internal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Signal I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Input Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Output Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Measurement (Handshaking OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Measurement (Handshaking ON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Commands Other than for Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Signal Operation in terms of Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
12
ZFX-C User’s Manual
7.APPENDICES
Error Messages and Corrective Actions. . . . . . . . . . . . . . . . . . . . . . . . . 176
List of Available Functions for Each Camera . . . . . . . . . . . . . . . . . . . . . 177
AUTO Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
AUTO Setting of Measurement Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
AUTO Setting in Individual Adjustment Screens . . . . . . . . . . . . . . . . . . . . . . . . 179
Specifications and External Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 181
Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Accessories & Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
LED Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Requirements from Regulations and Standards . . . . . . . . . . . . . . . . . . 207
Summary of Requirements to Manufactures . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Summary of Requirements to User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Definitions of Laser Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Basic Knowledge for Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Menu List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
How Color Images are Processed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
Color Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
Color Pickup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Hue, Saturation and Brightness Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Version Upgrade Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
1
BEFORE USE
BEFORE USE
ZFX-C 14
System Configuration 14
Part Names and Functions 16
Mounting and Connecting Devices 19
Installing Cameras 19
Installing the Controller 25
Connecting Devices 28
Overview of Settings and Measurement 31
Operation Modes 31
Outline of MENU mode 32
Measurement Items and Banks 33
Initializing Controller Settings 35
Saving Setup Data 36
ZFX-C
14
ZFX-C User’s Manual
ZFX-C
The ZFX-C is a series of vision sensors that senses objects by their “surfaces.“ Objects captured by a camera
can be checked on the built-in 3.5-inch LCD monitor.
System Configuration
Basically, the ZFX-C is configured by the Controller and the camera.
Other external devices can be selected to be used in combination with the ZFX-C according to the user’s
specific requirements.
*1: The Touch Pen (ZFX-TP) is supplied with the Controller.
*2: The same image as in the Controller's LCD monitor can be displayed in the LCD monitor (option).
*3: The console can be used instead of the Controller's keys and menu buttons.
*4: Conforms to the SD Card “Physical layer specifications 1.01.”
File format: FAT16
*5: Only connector 1 for camera 1 is provided on the ZFX-C10H/C15H/C10/C15.
LCD monitor (option)
USB
Parallel I/O cable
ZFX-VP
Touch pen
(*1)
SD Card (*4)
FZ-M08 (*2)
Ethemet
PC
Console
ZFX-KP
(*3)
RS-232C cable
ZFX-XPT_A
RS-422 cable
ZFX-XPT_B
Cameras with lighting
- Color camera
Camera only
Controller
ZFX-C20/C25/C10H/C15H/C10/C15 (*5)
A CCTV lens and light
source will be required.
(cable built-in)
- Color camera
ZFX-SC90_
ZFX-SC150_
ZFX-SC10_
ZFX-SC50_
- Monochrome camera
ZFX-SR10_
ZFX-SR50_
ZFX-SC
- Monochrome camera
Monitor cable
FZ-VM
ZFX-VS__/VSR__
Camera cable
ZFX-S
PLC
33 42
1
ZFX-C
ZFX-C User’s Manual
1
BEFORE USE
15
Options
Extension cable for connecting cameras and the Controller
*1: Up to two ZFX-XC_A/XC-AR can be connected between the camera cable and the Controller.
*2: Up to two ZEX-XC_A/XC-AR can be connected to the camera cable as long as the total cable length
between the Controller and the camera does not exceed 19 m.
*3: The total cable length between the Controller and the camera cannot exceed 28.4 m including camera
cables. The ZFX-XC_A/XC_AR cannot be used in this combination.
Optional lighting
The following optional lighting can be connected to ZFX-SC50_/SC90_.
• Bar lighting ZFV-LTL01
• Bar double-lighting ZFV-LTL02
• Bar low-angle lighting ZFV-LTL04
• Light Source for Through-beam Lighting ZFV-LTF01
Cameras with Lighting
2 m
Extension cable
(cable built-in)
ZFX-XC_A/XC_AR
3m/8m
(*1)
5 to 18 m
18 to 27.4 m
0.2m
ZFX-XEQ02
15m/25m0.2m
ZFX-XC_BRZFX-XEQ01
Extension cable
ZFX-XC_A/XC_AR
3m/8m
(*1,*2)
0.2m
ZFX-XEQ02
15m/25m0.2m
ZFX-XC_BRZFX-XEQ01
Camera only
3 m/8 m
Camera cable
ZFX-VS/VSR
8 to 19 m
19 to 28.4 m
(*3)
ZFX-C
16
ZFX-C User’s Manual
Part Names and Functions
Cameras
Cameras with lighting
Camera only (C-mount type)
Name. Description
(1) Optional lighting connector This connector is used to connect an optional lighting. (ZFX-SC50_/SC90_)
When no optional lighting is used, make sure that the connector is covered with the
cap. If not, water-resistant performance will be deteriorated.
(2) Ventilation film This film prevents the front panel from condensation.
• Do not peel off or probe the ventilation film with a sharp-pointed object. If you do
that the protective structure rating may no longer be satisfied.
• Do not cover the ventilation film rating. Doing so might cause the front panel to be
condensed.
(3) Focus adjustment control This control is used for adjusting the focus of the image.
(4) Mounting fixture This mounting fixture is used for fastening the camera when installing it. The mount-
ing fixture can be installed on all of the four mounting surfaces.
(5) Lighting connector This connector is used to connect external lighting (Strobe Controller: 3Z4S-LT
MLEK-C100E1TSX). Note, however, that the Strobe Controller cannot be connected
when the right angle camera cable is used.
(6) Camera cable connector
This connector is used for connecting to the Controller via a camera cable (ZFX-VS__/VSR__).
(7) Camera mounting base
This camera mounting base is fastened with screws to hold the camera in place. The camera
mounting base can be installed on all of the four mounting surfaces.
(2)
(3)
(4)
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
(2)
(3)
(4)
(2)
ZFXSC10_/SR10_/SR50_
ZFX-SC50_
ZFX-SC90_ ZFX-SC150_
(5)
(6)
(7)
ZFX-S/SC
Important
Important
ZFX-C
ZFX-C User’s Manual
1
BEFORE USE
17
Controller
Front
Note: The judgment result is output to the OR signal via the parallel interface.
Name Function
(1) Indicator “Measuring” indicator (RUN): Lights in green when in the RUN mode.
Error indicator (ERROR): Lights in red when an error occurs.
Judgment indicator (OUTPUT): Lights in orange when the judgment result is
OK or NG according to the setting. (Note)
Trigger indicator (ENABLE): Lights in blue when the ZFX-C is ready for the
measurement trigger input.
(2) LCD monitor/touch panel The LCD monitor displays setup menus and images captured from the cam-
eras. Various settings can be made on the touch panel by tapping menu buttons in the LCD monitor using the touch pen.
(3) Function keys Specific functions are allocated to the Function keys.
(4) Touch pen The touch pen is used to operate the touch panel. This pen can be attached to
the Controller by tying its strap to the strap holder for the touch pen.
(5) USB port This port is for connecting to a personal computer via a USB cable.
(6) SD card slot This slot is for inserting the SD Card.
When the SD Card is inserted, the SD mark is displayed at the top right of the
screen.
Blue SD mark: The SD card is inserted but not being accessed.
Red SD mark: The SD card is being accessed.
(7) Mode switch This switch selects the operation mode.
MENU: Select this mode when setting measurement conditions.
ADJ: Select this mode when adjusting setting parameters as necessary refer-
encing the image and values displayed on the LCD monitor during continuous test measurement (measurement without measurement data
output to external devices).
RUN: Select this mode when performing measurement.
(8) Control keys These keys are used to perform operations without the use of the touch pen.
(9) Strap holder for touch pen This holder is for attaching the touch pen.
PULL OPEN
1234
OMRON
ZFX-C10
OUTPUT
RUN
ERROR
ENABLE
MENU RUN
SD
CARD
ADJ
USB
AUTO ESC
SET
ETHERNET
PARALLEL1
CONSOLE
RS-232C
PARALLEL0
CAMERA1
RGB
CAMERA2
(1)
(4)
(2)
(3)
(9)
(5)
(1)
(1)
(4)(5)
(2) (3)
(2)
(6)
(7)
(8)
Operation
panel cover
Front
Top
Bottom
ZFX-C
18
ZFX-C User’s Manual
Top
Bottom
• Attach the connector caps to connectors that are not in use to prevent dust or dirt from getting inside the connectors
and to prevent the Controller from static electricity.
Name Function
(1) Monitor connector This connector is for connecting to the LCD monitor (option) via a monitor
cable.
(2) Camera connector This connector is for connecting to a camera.
Name Function
(1) Ethernet port This port is for connecting to a personal computer via a 100Base-TX/10Base-T
cable.
(2) RS-232C/422 connector This connector is for connecting to a PLC via an RS-232C or an RS-422 cable.
p.14
(3) Console connector
This port is for connecting to the Console.
p.14
(4) Power connector
This connector is for connecting to the DC power supply.
p.28
(5)Parallel port This port is for connecting to devices such as a PLC using the parallel cable.
p.14
, p.156
Important
1
BEFORE USE
Mounting and Connecting Devices
ZFX-C User’s Manual
19
Mounting and Connecting Devices
Installing Cameras
Camera with Lighting
Optical chart
ZFX-SC10_/SR10_
ZFX-SR50_ ZFX-SC50_
ZFX-SC90_ ZFX-SC150_
Setting distance (L)
Detection range (H)
8.9
104
4.9
0
34
49
50
60
Setting distance L (mm)
Detection range H (mm)
9
9.8 49
60
30
38
100
194
300
Setting distance L (mm)
Detection range H (mm)
100
9.8
30
31
187
190
49
Setting distance L (mm)
Detection range H (mm)
Setting distance L (mm)
Detection range H (mm)
70
89
10040
40
67
100
142
160
49
Setting distance L (mm)
Detection range H (mm)
100
148
160
12080
115
180
227
240
89
Mounting and Connecting Devices
20
ZFX-C User’s Manual
Installing the mounting fixture
The mounting fixture can be installed on all of the four mounting surfaces.
ZFX-SR10R/SR50R/SC10R/SC50R/SC90R (robot cable type)
1 Install the mounting fixture with the protrusion on its
base (black) aligned with the groove on the camera
body.
2 Install the mounting fixture on the camera body with
the bracket (silver) aligned with the base.
3 Tighten the base and the bracket with the provided
screws (M3 x 6).
Tightening torque: 0.54N
⋅ m
4 Fasten the base at the mounting position with screws.
Tightening torque
M4: 1.2 N
⋅ m
1/4"-20UNC: 2.6 N
⋅ m
Except ZFX-SR10R/SR50R/SC10R/SC50R/SC90R (normal cable type)
1 Align the two hooks on one side of the mounting fix-
ture with the two grooves on the camera body.
2 Push the other hook down until it is snapped into
place.
Make sure that the mounting fixture is firmly fixed on the
camera.
• The lens has a fixed focal point. The actual detection range and focal point vary from lens to lens, so adjust the
distance to the measurement target after replacing the lens or camera.
• The camera mounting distance listed in the following tables is an approximate value. Mount the Camera so that
the distance to the measurement target can be adjusted easily.
• If the object size and detection range are incompatible, use a combination of a camera (without lighting), standard
CCTV lens and light source.
Camera Only p.22
Note
Bracket
Base
Hooks
Grooves on camera
Mounting
fixture
Mounting and Connecting Devices
ZFX-C User’s Manual
1
BEFORE USE
21
3 Fasten the mounting fixture at the mounting location
with screws.
Tightening torque
M4: 1.2 N•m
1/4”-20 UNC: 2.6 N•m
Removal procedure
1 Insert a screwdriver into the gap (one of the two gaps) be-
tween the mounting fixture and the camera case, and re-
move the mounting fixture
.
Adjusting the camera focus
1 Adjust the distance between the camera and the mea-
surement target and fasten the camera.
Refer to the optical chart and set the camera in a position
so that the area to be checked is within the detection area
(LCD monitor).
Optical chart p.19
2 Turn the focus adjustment control to the left and right
to adjust the focus.
First turn the focus adjustment control slightly to the left and right, to make sure that the Focus adjustment control is
not at the upper or lower limit positions. Do not exert unnecessary force to turn the control at the upper or lower limit
positions as this might damage the control.
(For ZFX-SC90_/SC150_, the control stops turning at the nearest position. It turns free at the farthest position.)
Mounting fixture
Setting distance (L)
Detection range (H)
Focus
adjustment
control
Note
Mounting and Connecting Devices
22
ZFX-C User’s Manual
Camera Only
Optical chart
The values in the following chart are approximations, and the Camera must be adjusted after it is mounted.
t2
t0
t40
t2
t5
t15
t20
t50
t5
t10
t15
t20
110 100 1000
100
1000
10000
t30
t10
t60
t50
t40
t30
t0
ML-10035
ML-7527
Detection range (mm)
Camera distance A (mm)
Lens model
3Z4S-LE
10
100
1000
10000
110 100 1000
t1
t1
t5
t0
t2
t40
t35
t30
t25
t20
t15
t10
t5
t2
t1
t0
t25
t20
t15
t10
t5
t2
t1
t0
t20
t15
t10
t2
t0
t10
t5
t1.5
t0.5
t1
t0
t2
t0
t1.5
t0
t1
t0.5
t1
t0.5
ML-0614
ML-0813
ML-1214
ML-1614
ML-2514
ML-3519
ML-5018
Lens model
3Z4S-LE
t0.5
t1.5
Detection range (mm)
Camera distance A (mm)
t: Extension tube
Example
t0: Extension tube
is not required.
t5: 5-mm extension
tube is required.
Mounting and Connecting Devices
ZFX-C User’s Manual
1
BEFORE USE
23
The X axis of the optical chart shows detection range L (mm), and the Y axis shows the camera distance A
(mm). The curves on the optical chart show the relationship between the detection range and camera distance
for each CCTV lens. The values are significantly different for each lens, so double-check the model of the lens
before using the graph. The “t” values indicate the lengths of the Extension Tubes. The value “t0” shows the
case where an Extension Tube is not required and the value “t5.0” shows the case where a 5-mm Extension
Tube is used.
Example
When a 3Z4S-LE ML-5018 CCTV Lens is being used and a detection range of 40 mm is required at the
measurement target, a camera distance of 500 mm and 5-mm Extension Tube are required.
Lenses and lens diameters
Lens Focal length Brightness
Maximum outer diameter
Total length Filter size
3Z4S-LE ML-0614 6 mm F1.4 30 mm dia. 30 mm M27 P0.5
3Z4S-LE ML-0813 8 mm F1.3 30 mm dia. 34.5 mm M25.5 P0.5
3Z4S-LE ML-1214 12 mm F1.4 30 mm dia. 34.5 mm M27 P0.5
3Z4S-LE ML-1614 16 mm F1.4 30 mm dia. 24.5 mm M27 P0.5
3Z4S-LE ML-2514 25 mm F1.4 30 mm dia. 24.5 mm M27 P0.5
3Z4S-LE ML-3519 35 mm F1.9 30 mm dia. 29 mm M27 P0.5
3Z4S-LE ML-5018 50 mm F1.8 32 mm dia. 37 mm M30.5 P0.5
3Z4S-LE ML-7527 75 mm F2.7 32 mm dia. 42.5 mm M30.5 P0.5
3Z4S-LE ML-10035 100 mm F3.5 32 mm dia. 43.9 mm M30.5 P0.5
Extension Tube t_ (mm)
Camera
Lens
Measurement object
Camera distance A (mm)
Detection range L (mm)
1-32 UNF
(C-mount
thread)
Filter thread
Total length
Max. dia.
Mounting and Connecting Devices
24
ZFX-C User’s Manual
Extension Tubes
One or more Extension Tubes can be inserted between the lens and the Camera to focus the Camera image.
Use a combination of one or more of the seven tubes to achieve the required length.
• Do not use the 0.5-mm, 1.0-mm and 2.0-mm Extension Tubes attached to each other. Since these Extension Tubes
are placed over the threaded section of the Lens or other Extension Tube, the connection may loosen when more
than one 0.5-mm, 1.0-mm or 2.0-mm Extension Tube are used together.
• Reinforcement may be required for combinations of Extension Tubes exceeding 30 mm if the Camera is subject to
vibration.
Installing the Camera Mounting Base
The camera mounting base mounted on the bottom of the camera can be installed on all of the four mounting
surfaces. To change the mounting surface, remove the three mounting screws (M2 x 6) from the camera.
• Tightening torque when fastening the camera mounting base at the mounting location
M4: 1.2 N•m
1/4”-20 UNC: 2.6 N•m
Model
Maximum outer diameter
Length
3Z4S-LE ML-EXR 31 dia. Set of 7 tubes
Extension Tube
Length: 40 mm 20 mm 10 mm 5 mm 1 mm2 mm 0.5 mm
Important
Camera Mounting Base
Mounting and Connecting Devices
ZFX-C User’s Manual
1
BEFORE USE
25
Installing the Controller
Installation Precautions
To improve heat radiation, install the Controller only in the orientation show below.
Do not install the Controller in the following orientations.
• Install the Controller so that the distance between the Controller and other devices is at least the dimensions shown
in the figure below to improve the ventilation.
• Keep the ambient temperature less than 50 °C. If the ambient temperature is higher than 50 °C, install a fan forced
cooling system or an air conditioner to keep the temperature lower than 50 °C.
• Avoid mounting on a panel, in which high-voltage emitting devices are installed to prevent ZFX-C operation from
being affected by noise.
• Allow at least 10 m between the Controller and power lines to keep noise at a low level in the operating environ-
ment.
Right
Wrong Wrong
Important
Min.
50 mm
Min.
15 mm
When installing Controller only:
When installing the Controller With the Exhaust Unit
attached:
Min.
50 mm
Min. 15 mm
Mounting and Connecting Devices
26
ZFX-C User’s Manual
Installing on the DIN Track
1 Hook the Controller’s upper hook onto the DIN track.
2 Push the Controller down onto the DIN track until its
lower hook is snapped into place.
•Attach the End Plate (sold separately) to both sides of the
Controller on the DIN track.
•Attach the Exhaust Unit (supplied) to the Controller when
installing other devices adjacently on the same DIN track
as the Controller.
p.30
Removing procedure
1 Pull the Controller’s lower hook downwards.
2 Lift up the Controller from its bottom to remove it from
the DIN track.
1
2
Important
PULL OPEN
1234
OMRON
ZFX-C10
OUTPUT
RUN
ERROR
ENABLE
MENU RUN
SD
CARD
ADJ
USB
AUTO ESC
SET
DIN track (sold separately)
End Plate (sold separately)
PFP-M
PFP-100N (1 m)
PFP-50N (0.5 m)
PFP-100N2 (1 m)
Exhaust Unit
1
2
Mounting and Connecting Devices
ZFX-C User’s Manual
1
BEFORE USE
27
Mounting on a Panel
1 Install the long Panel Mount Adapters on the four
holes on the Controller.
2 Install the short Panel Mount Adapters on the two
holes on the long Panel Mount Adapter.
3 Install the Controller with Mount Adapters attached
onto the panel from the front.
4 Hook the hooks of the mounting bracket onto the two
holes (two each at top and bottom) of the longer
Mount Adapters and tighten the screws.
Tightening torque: 1.2 N•m.
5 Make sure that the Controller is firmly fixed on the
panel.
1
1
2
2
3
Panel mount adapters
Panel
4
Mounting bracket
Loading...