Omron GI-S, GI-SID1224, GI-SMD1624 Original Instructions Manual

Original Instructions

GI-S series Safety I/O Terminal

GI-S□□□□□□

Instruction SHEET

OMRON Corporation

OMRON Corporation

©

2018

All Rights Reserved.

4022169-1A

●Current restrictions from power supply

connector

The external power supplies must be DC power
supplies that satisfy the SELV requirements.

Unit Power
(SELV)

DINtrack

●Electric Ratings

Source

Input

Output

*GI-SMD1624 only.

V0 port: 24 VDC -15%/+20% SELV, 5.1 A max. (0.3 A with no load)
*V1 port: 24 VDC -15%/+20% SELV, 2 A max. (0.1 A with no load)

24 VDC SELV, 6 mA/point(GEN.), 12 points
T0-T11: 24 VDC, 0.7 A/point (GEN.), 12 points, 5 A/unit
*OUT0-OUT3: 24 VDC, 0.5 A/point (GEN.), 4 points, 2 A/unit

Precautions for Compliance with

UL Standards, CSA Standards

and EU Directives

Notice to Users of the GI series Safety I/O
Terminal GI-SMD1624 and GI-SID1224 in USA,
Canada and Europe

This instruction must be consulted in all cases in
order to find out the nature of the potential
HAZARDOUS and any actions which have to be
taken to avoid them.
If the equipment is used in a manner not specified
by the manufacturer, the protection provided by the
equipment may be impaired.
This product is defined as an in-panel device and
must be installed within a control panel.

●Definition of Precautionary Information

Indicates a potentially hazardous

Caution

●Environment

for Indoor use only

Ambient Air Temperature 0 to 55°C

Relative Humidity

Altitude 2,000 m max.
Pollution Degree 2
Terminal Temperature 80°C
Degree of Protection IP20

situation which, if not avoided,
may result in minor or moderate
injury, or property damage.

10% to 95% (with no
condensation or no icing)

Output Power *
(SELV)

*GI-SMD1624 only

Safety I/O Terminal

Over-current protection
(Current limitation:
F5A, 24 VDC min.)

Use fuses of either of the
following categories

• cULus Listed

• UL Listed and CSA certified

●Direction for installation

The product can be installed in six directions of the
figure below.

<Vertical>

<Vertical Rotate 180˚>

<Horizontal Rotate 180˚> <Horizontal>

<Left side up> <Right side up>

●I/O Wiring Diagram

GI-SMD1624
24 VDC input (12 point)

GI-SID1224
24 VDC input (12 point)

Sourcing Output (4 point)

Upper Terminal Block

Upper Terminal Block

24 VDC 24 VDC

Lower Terminal Block Lower Terminal Block

24 VDC

The input terminals (IN0-IN11) are not isolated from the internal circuit of the Safety I/O Terminal.
When the external devices are connected to the input terminals (IN0-IN11) of the Safety I/O Terminal, the power
of the external devices must be supplied from the Unit Power supply or Test output terminals (T0-T11).

●Marking

: Functional Earth Terminal

●Cleaning

Do not use paint thinner or similar chemical to
clean with. Use a dry cloth.

●Enclosure type

Please use this product in a control panel.
Enclosure type: Type 1 or more.

Conformance to UL Standards

and CSA Standards

Compliance with Class I Division 2

●

Hazardous Location:

Input and output wiring must be in accordance
with Class I, Div. 2 wiring methods and in
accordance with the authority having jurisdiction.

1. This equipment is suitable for use in Class I,
Div.2, Group A, B, C, D or Non-Hazardous
Locations Only.

2. WARNING : Explosion Hazard - Do not
Disconnect Equipment Unless Power Has
Been Switched off or the Area Is Known to Be
Non-Hazardous.

3. This device is open-type and is required to be
installed in an enclosure suitable for the
environment and can only be accessed with
the use of a tool or key.

1. Cet equipement convient a l'utilisation dans
des emplacements de Classe I, Division 2,
Groupes A, B, C, D, ou ne convient qu'a
l'utilisation dans des endroits non dangereux.

2. AVERTISSEMENT : Risque d'explosion ­Avant de debrancher l'equipement, couper le
courant ou s'assurer que l'emplacement est
designe non dangereux.

3. Ce dispositif est de type ouvert et doit etre
installe dans un coffret adapte a
l'environnement et auquel on ne pourra
acceder uniquement au moyen d'un outil ou
d'une cle.

T code: T4A

Conformance to EU Directives

This product is EMC-compliant when assembled in
PLC system or Machine Automation Controller.
To ensure the EU Directive conformance of
customer's machinery or equipment in which the
product is incorporated, be sure to observe the
following precautions.

1. This product is defined as an in-panel device and
must be installed within a control panel.

2. This product complies with the common emission
standard (EN61131-2, EN61000-6-4) with regard
to EMI. For the radiated emission requirement
(10-m regulations), in particular, please note that
the actual emission varies depending on the
configuration of the control panel to be used, the
connected devices, and wiring methods.
Therefore, the customer must confirm the EU
Directive conformance of the overall machinery or
equipment by themselves, even if this EU
conforming product is used.

This is a class A product. In residential areas it
may cause radio interference, in which case the
user may be required to take adequate measures
to reduce interference.
We have confirmed that this product conforms to
EMC standards with OMRON S8VS series Power
Supplies.

Conformance to KC Standards

●Ａ급 기기󴀊업무용 방송통신기자재󴀋이
기기는업무용Ａ급전자파적합기기로서
판매자 또는 사용자는 이 점을 주의하시기 바라며,
가정외의 지역에서 사용하는 것을 목적으로
합니다.

本書は英語オリジナル版の翻訳です。

GI-S

シリーズセーフティI/Oターミナル

形GI-S□□□□□□

JA

OMRON Corporation

©

取扱説明書

2018

All Rights Reserved.

4022169-1A

●電源コネクタからの電流に対する制限

外部電源はSELV要件を満たすDC電源を使用してくだ

さい。

ユニット電源

(SELV)

出力電源*

(SELV)

*形GI-SMD1624のみ

セーフティI/Oターミナル

過電流保護

(電流制限:F5A,DC24V以上)

次のカテゴリーのいずれかの

ヒューズを使用してください。

•cULus認証取得済み

•UL認証およびCSA認証取得済み

DINレール

●I/O配線図

形GI-SMD1624

DC24V入力(12点)

ソース出力(4点)

上部端子台

セーフティI/Oターミナル形GI-SMD1624および

形GI-SID1224の欧州ユーザーへの通知

本マニュアルは、潜在的な危険およびその回避策を調べ

る際に必ず参照してください。

製造元の指定した方法に従わず機器を使用した場合、機

器の保護が損なわれることがあります。

この製品は盤内装置として定義されており、必ず制御盤

の中に設置してください。

●設置方向

この製品は下図の6方向に設置できます。

<縦>

<縦180°回転>

<横180°回転> <横>

<左上> <

右上

>

形GI-SID1224

DC24V入力(12点)

上部端子台

●Applicable wire size

Type Wire size Wire size

Conductor

surface
Solid/Strand AWG 28-16 9 mm Plated
Solid/Strand AWG 14* 11 mm Plated

*AWG 14 only use by Functional Earth Terminal.

Use Copper Conductors Only.

Do not use ferrule terminals. Insert the strand or
solid wire directly into the holes on the terminal
block.
Please select wire size suitable for rated current.

OMRON Corporation

Shiokoji Horikawa, Shimogyo-ku, Kyoto, 600-8530 Japan
Tel: [phone] Fax: [phone]
Contact: www.ia.omron.com

Regional Headquarters

OMRON EUROPE B.V.

Wegalaan 67-69,2132 JD Hoofddorp,
Tel: [phone] Fax: [phone]

OMRON ASIA PACIFIC PTE. LTD.

No. 438A Alexandra Road # 05-05/08 (Lobby 2), Alexandra Technopark,
Singapore 119967
Tel: [phone] Fax: [phone]

OMRON ELECTRONICS LLC

2895 Greenspoint Parkway, Suite 200 Hoffman Estates, IL 60169 U.S.A.
Tel: [phone] Fax: [phone]

OMRON (CHINA) CO., LTD.

Room 2211, Bank of China Tower, 200 Yin Cheng Zhong Road, Pu
Dong New Area, Shanghai, 200120, China
Tel: [phone] Fax: [phone]
Note: Specifications subject to change without notice.
Printed in China

(Manufacturer)

(Importer in EU)

The Netherlands

DC24VDC24V

下部端子台下部端子台

DC24V

●記号

: 機能接地端子

Übersetzung der Originalbetriebsanleitung

Hinweis für europäische Benutzer der
Sicherheits-E/V-Anschlüsse GI-SMD1624 und
GI-SID1224 der GI-Serie

Diese Anleitung muss stets herangezogen werden,

Sicherheits-E/V-Anschluss der GI-Serie

GI-S□□□□□□

DE

OMRON Corporation

OMRON Corporation

©

●

Strombeschränkungen des Stromversorgungssteckers

Die externen Stromversorgungen müssen
Gleichstromanschlüsse sein, die die

BEDIENUNGSANLEITUNG

2018

All Rights Reserved.

4022169-1A

um potentielle GEFAHREN sowie alle Maßnahmen,
die ergriffen werden müssen, um diese zu
vermeiden, in Erfahrung zu bringen.
Wird das Gerät auf eine Weise genutzt, wie sie nicht
vom Hersteller vorgesehen wurde, kann dies die
vom Gerät gebotene Sicherheit beeinträchtigen.
Bei diesem Produkt handelt es sich um ein
Einbauelement für Bedienpanels und muss als
solches in einem Bedienpanel installiert werden.

●Ausrichtung

SELV-Anforderungen erfüllen.

Leistung der Einheit
(SELV)

Ausgangsleistung*
(SELV)

*nur GI-SMD1624

Sicherheits-E/V-Anschluss

Überstromschutz
(Strombegrenzung:
F5A, 24 VDC min.)

Benutzen Sie Sicherungen
folgender Kategorien

• cULus Listed

• UL Listed und CSA certified

DIN-Schiene

<Horizontal, rotiert um 180°> <Horizontal>

●E/A-Verdrahtungsplan

GI-SMD1624
24 VDC Eingang (12 Punkte)

GI-SID1224
24 VDC Eingang (12 Punkte)

Aktiver Ausgang (4 Punkte)

Das Produkt kann in den folgenden sechs
Ausrichtungen installiert werden.

<Vertikal>

<Vertikal, rotiert um 180°>

<Linke Seite oben> <Rechte Seite oben>

Traduction de la notice

Remarques à l'attention des utilisateurs des
terminaux d'E/S de sécurité GI-SMD1624 et
GI-SID1224 en Europe.

Vous devez toujours vous référer à cette notice pour

Terminal d'E/S de sécurité de la série GI-S

GI-S□□□□□□

FR

OMRON Corporation

OMRON Corporation

©

●Limitation de courant par le connecteur

d'alimentation

Les alimentations externes doivent être des
alimentations CC qui répondent aux normes

FICHE D’INSTRUCTIONS

2018

All Rights Reserved.

4022169-1A

connaître la nature des DANGERS potentiels et les
mesures à prendre pour les éviter.
Toute utilisation de cet équipement non prévue par
le fabricant peut altérer la protection qu'il est sensé
procurer.
Ce produit a été conçu pour fonctionner à l'intérieur
d'un panneau de contrôle et doit donc y être installé.

●Sens d'installation

Le dispositif peut être installé dans les six
directions indiquées ci-dessous.

TBTS.

Puissance de l'unité
(TBTS)

Puissance de sortie*
(TBTS)

*Uniquement pour

GI-SMD1624

Terminal d'E/S de sécurité

Protection contre les surintensités
(limitation de courant :
F5A, 24 Vcc min.)

Utilisez des fusibles de l'une
des catégories suivantes

• homologués cULus

• homologués UL et certifiés CSA

RailDIN

<

Rotation horizontale de 180°

Avec le côté gauche v ers le haut><Avec le côté droit vers le haut

<

●Schéma de câblage E/S

GI-SMD1624
Entrée 24 Vcc (12 points)

GI-SID1224
Entrée 24 Vcc (12 points)

Sortie Source (4 points)

<Verticale>

<

Rotation verticale de 180°

> <Horizontale>

>

>

Oberer Anschlussblock

Oberer Anschlussblock

24 VDC 24 VDC

Unterer Anschlussblock Unterer Anschlussblock

24 VDC

●Symbol

: Funktionserdeanschluss

Traduzione delle istruzioni originali

Avviso agli utenti della serie GI di terminali I/O
di sicurezza GI-SMD1624 e GI-SID1224 in Europa

Queste istruzioni devono essere consultate in tutti i

Terminale I/O di sicurezza, serie GI-S

GI-S□□□□□□

IT

OMRON Corporation

OMRON Corporation

©

●Restrizioni della corrente dal connettore

all'alimentazione

Le alimentazioni esterne devono essere di tipo CC
e devono soddisfare i requisiti SELV.

Potenza unità
(SELV)

FOGLIO DI ISTRUZIONI

2018

All Rights Reserved.

4022169-1A

GuidaDIN

casi per poter individuare la natura dei RISCHI
potenziali e le azioni da intraprendere per evitarli.
Se l'attrezzatura è utilizzata in un modo non
specificato dal fabbricante, la protezione fornita con
l'attrezzatura potrebbe essere compromessa.
Questo prodotto è definito come un dispositivo
integrato nel pannello e deve essere installato
all'interno del pannello di controllo.

●Orientamento per l'installazione

Si può installare il prodotto nelle sei direzioni
descritte nell'immagine sottostante.

<Verticale>

Verticale ruotato di 180°

<

Bornier supérieur

24 Vcc 24 Vcc

Bornier inférieur Bornier inférieur

24 Vcc

●Symbole

: Borne de terre fonctionnelle

Traduccióndelmanualoriginal

Terminales de E/S de seguridad de la Serie GI-S

GI-S□□□□□□

ES

OMRON Corporation

OMRON Corporation

©

●Restricciones actuales del conector de

alimentación

Las fuentes de alimentación externas deben ser
fuentes de alimentación de CC que cumplan con
los requisitos de MBTS.

Unidad de alimentación
(MBTS)

>

HOJA DE INSTRUCCIONES

2018

All Rights Reserved.

4022169-1A

CarrilDIN

Bornier supérieur

Aviso a los usuarios del terminal de entrada y
salida de seguridad de la Serie GI-SMD1624 y
GI-SID1224 en Europa

Debe consultar estas instrucciones en todo
momento para conocer la naturaleza de los
posibles PELIGROS y saber qué medidas debe
tomar para evitarlos.
Si utiliza el equipo de una forma no especificada
por el fabricante, la protección proporcionada por el
equipo podría verse afectada.
Este producto es un dispositivo integrado en panel,
por lo que debe instalarse dentro de un panel de
control.

●Instrucciones de instalación

El producto se puede instalar en seis direcciones,
según la ilustración siguiente.

<Vertical>

Rotación vertical de 180°

<

>

Potenza d'uscita*
(SELV)

*solo GI-SMD1624

Terminale I/O di sicurezza

Protezione da sovracorrente
(Limitazione corrente:
F5A, 24 Vcc min.)

Utilizzare fusibili di una delle
seguenti categorie

• conformi cULus

• conformi UL e certificati CSA

<Orizzontale ruotato di 180°> <Orizzontale>

<Lato sinistro in alto> <Lato destro in alto>

●Schema elettrico I/O

GI-SMD1624
Ingresso 24 Vcc (12 punti)

GI-SID1224
Ingresso 24 Vcc (12 punti)

Uscita sourcing (4 punti)

Morsettiera superiore

Morsettiera superiore

24 Vcc 24 Vcc

Morsettiera inferiore Morsettiera inferiore

24 Vcc

Potencia de salida *
(MBTS)

*Solo GI-SMD1624

Terminal de entrada y salida de seguridad

Protección contra sobrecorriente
(limitación de corriente:
F5A, 24 V CC mín.)

Utilizar fusibles de cualquiera
de las siguientes categorías

• Estándar cULus

• Estándar UL y certificado CSA

●Cableado de entrada y salida

GI-SMD1624
Entrada de 24 V CC (12 puntos)

Rotación horizontal de 180°

<

Con el lado izquierdo hacia arriba

GI-SID1224
Entrada de 24 V CC (12 puntos)

> <Horizontal>

> <

<

Salida de suministro (4 puntos)

Regleta de conexiones superior

Regleta de conexiones superior

24 V CC 24 V CC

Regleta de conexiones inferior Regleta de conexiones inferior

24 V CC

Con el lado derecho hacia arriba

>

●Legenda

: Terminale di messa a terra

●Símbolo

:

Terminal de tierra funcional