Omron STC-SBE132POE, STC-SCE132POE, GigE Vision STC-SCS43POE, GigE Vision STC-SBS43POE, GigE Vision STC-SBS163POE Owner's Manual
...Page 1
GigE Vision
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Color / Monochrome CMOS PoE Camera
STC-SBE132POE (1.3M / Monochrome)
STC-SCE132POE (1.3M / Color)
No.14S002-08
Product Specifications and User’s Guide
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
1/53
Page 2
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Table of Contents
1 Product Precautions ............................................................................................ 7
2 Warranty ................................................................................................................ 7
3 Introduction .......................................................................................................... 8
3.1 Features .................................................................................................................................... 8
3.2 Product Number Naming Method ........................................................................................... 8
4 Specifications ....................................................................................................... 9
4.1 Electronic Specifications ......................................................................................................... 9
4.2 Spectral Sensitivity Characteristics ..................................................................................... 10
4.2.1 STC-SCE132POE / STC-SBE132POE ............................................................................................. 10
4.2.2 IF Cut Filter (STC-SCE132POE) ...................................................................................................... 10
4.3 Mechanical Specifications ..................................................................................................... 11
4.4 Environmental Specifications ............................................................................................... 11
5 Connector Specifications .................................................................................. 12
5.1 RJ45 Connector ...................................................................................................................... 12
5.2 Power / IO Control Signal Connector ................................................................................... 13
5.2.1 Equivalent Circuit for the Input Pin of the I/O Connector ............................................................. 15
5.2.2 Typical Input Circuit ........................................................................................................................ 16
5.2.3 Typical Output Circuit ..................................................................................................................... 17
5.2.4 Input and Output Signal Timing (Hardware Trigger) ..................................................................... 18
5.2.5 Input and Output Signal Timing (Software Trigger) ...................................................................... 19
6 Dimensions ......................................................................................................... 20
6.1 STC-SBE132POE .................................................................................................................... 20
6.2 STC-SCE132POE .................................................................................................................... 20
7 Sensor information ............................................................................................ 21
7.1 Pixel Transferring Image ........................................................................................................ 21
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
2/53
Page 3
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
8 Camera Operational Modes ............................................................................... 22
8.1 Normal Mode (TriggerMode=Off)........................................................................................... 22
8.2 Edge Preset Trigger Mode (ExposureMode=Timed) ............................................................ 22
8.2.1 Timing .............................................................................................................................................. 22
8.2.2 Exposure Timing with the Positive Polarity Trigger Signal .......................................................... 23
8.2.3 Exposure Timing with the Negative Polarity Trigger signal ......................................................... 23
8.3 CMOS Rest Type ..................................................................................................................... 24
9 Camera Functions .............................................................................................. 25
9.1 ROI (Region of Interest) ......................................................................................................... 25
9.1.1 ROI (1 region) .................................................................................................................................. 25
9.2 Pixel Format ............................................................................................................................ 27
9.3 Binning .................................................................................................................................... 27
9.4 Decimation .............................................................................................................................. 28
9.5 Image Flip................................................................................................................................ 29
9.6 Gain ......................................................................................................................................... 31
9.6.1 Analog gain ..................................................................................................................................... 31
9.6.2 Digital gain ...................................................................................................................................... 31
9.7 Black level ............................................................................................................................... 31
9.8 ALC (Auto Light Control) ....................................................................................................... 32
9.8.1 ALC control method........................................................................................................................ 33
9.8.2 AGC (Auto Gain Contorl) ................................................................................................................ 33
9.8.3 Auto shutter .................................................................................................................................... 34
9.8.4 ALC settings procedure ................................................................................................................. 34
9.9 White balance (Only available for the color cameras) ........................................................ 35
9.9.1 White balance control methods ..................................................................................................... 35
9.9.2 OFF .................................................................................................................................................. 36
9.9.3 Auto white balance ......................................................................................................................... 36
9.9.4 Push to set white balance .............................................................................................................. 36
9.9.5 Preset white balance1 to 3 ............................................................................................................. 37
9.9.6 White balance calculate area setting ............................................................................................. 38
9.10 Gamma correction ............................................................................................................... 39
9.10.1 Gamma table writing.................................................................................................................... 39
9.11 Save and load the camera setting data ............................................................................. 40
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
3/53
Page 4
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.11.1 Saving the Camera Settings ........................................................................................................ 40
9.11.2 Loading Camera Settings ............................................................................................................ 41
9.11.3 Loading Camera Settings when the Camera Power is on ......................................................... 41
9.11.4 Camera Settings Initialization ..................................................................................................... 41
9.12 Trigger .................................................................................................................................. 42
9.12.1 Trigger Signal Processing Process ............................................................................................ 42
9.13 The camera settings (GenICam parameters) control with SDK ....................................... 43
9.13.1 Integer type parameter control ................................................................................................... 43
9.13.2 Float type parameter control ....................................................................................................... 43
9.13.3 Enumeration type parameter control ......................................................................................... 43
9.13.4 String type paramter control ....................................................................................................... 44
9.13.5 Boolean type parameter control ................................................................................................. 44
9.13.6 Command type paramter control ................................................................................................ 44
9.14 GenICam Command List ..................................................................................................... 45
9.14.1 DeviceControl .............................................................................................................................. 45
9.14.2 ImageFormatControl.................................................................................................................... 45
9.14.3 AcquisitionControl ...................................................................................................................... 46
9.14.4 DigitalIOControl ........................................................................................................................... 46
9.14.5 CounterAndTimerControl ............................................................................................................ 47
9.14.6 EventControl ................................................................................................................................ 47
9.14.7 AnalogControl .............................................................................................................................. 47
9.14.8 TransportLayerControl ................................................................................................................ 48
9.14.9 UserSetControl ............................................................................................................................ 49
9.14.10 IPEngine ....................................................................................................................................... 49
9.14.11 SpecialFeatures ........................................................................................................................... 50
10 Revision History ................................................................................................. 52
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
4/53
Page 5
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Precautions for safe use
Please read carefully this “Precautions for safe use” before use the camera. Then the camera uses correctly with
agreeing with below notes.
In this “Precautions for safe use”, notes divides into “Warning” and “Caution” to use the camera safety and prevent to
harm and damage.
This shows, assumption for possibility of serious accident leading death or
Warning
Caution
About Graphic
symbols
[Environment / condition]
serious injury if ignore this note and camera uses incorrectly.
This shows, assumption for possibility of bear the damage or physical
damage if ignore this note and camera uses incorrectly.
This symbol shows general prohibition.
This symbol shows completion or instruction.
Warning
Do not use flammable or explosiveness
atmospheres.
This will cause of personal injury or fire.
Caution
Use and store under specified environmental
conditions (Vibration, shock, temperature,
humidity) in the specifications for this camera.
This will cause of fire or damage the camera.
[Installation and cable wiring]
Warning
Do not use with out of power voltage range
that is specified in the specifications for this
camera.
This will cause of fire, electrification or
malfunction.
Do not use for “safety for human body” related
usage.
This camera is designed for use “do not harm
human body immediately” if by any chance the
camera has malfunction.
Do not wrong wiring.
This will cause of fire or malfunction.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
5/53
Page 6
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Caution
The camera housing is not connecting to 0 V line
of camera inside circuit.
There is a risk of short circuit between camera
inside ciurcuit and frame ground through other
devices.
This will cause of malfunction.
It is necessary to wiring with turn off the camera.
This will cause of electrification or malfunction.
[Usage instruction]
No.14S002-08
It is necessary to wiring and mounting that is
specified in the specifications for this camera.
This will cause of fire or malfunction.
It is necessary to mounting the camera without
stress for the cable.
This will case of electrification or fire.
Warning
Do not touch the terminal and PCB board
While turn on the camera.
This will cause of electrification or accident
caused by malfunction.
Do not use without usage that is specified in
the specifications for this camera.
This will cause of personal injury or malfunction.
Caution
Do not push contamination into opening of
the camera.
This will cause of electrification or malfunction.
[Maintenance]
Caution
Do not disassemble or repair the camera.
This will cause of fire, electrification or
malfunction.
[Disposal]
Do not put combustibles near the camera.
This will cause of fire.
Do not push metals including screw driver into
radiation holes.
This will cause of electrification or malfunction.
Do not block the radiation holes.
This will cause of fire due to increase the
camera inside temperature.
It is turn off the camera when maintaining or
inspecting the camera.
This will cause of electrification.
Caution
It is necessary to dispose as industrial waste.
]
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
6/53
Page 7
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
1 Product Precautions
Do not give shock to the camera.
Do not haul or damage the camera cable.
Do not wrap the camera with any material while using the camera. This will cause the internal camera
temperature to increase.
When the camera moving or using the place that temperature difference is extreme, countermeasure for dew
condensation (heat removal / cold removal) is necessary.
While the camera is not using, keep the lens cap on the camera to prevent dust or contamination from getting
in the sensor or filter and scratching or damaging it.
Do not keep the camera under the following conditions.
・ In wet, moist, high humidity or dusty place
・ Under direct sunlight
・ In extreme high or low temperature place
・ Near an object that releases a strong magnetic or electric filed
・ Place with strong vibrations
Apply the power that satisfies the specified in specifications for the camera.
The defective pixels may appear due to the sensor characteristics.
Use below recommend materials (or equivalent materials) to clean the surface of glass.
・ Air dust: Non Freon air duster (NAKABAYASHI Co., LTD.)
・ Alcohol: Propan-2-ol (SAN’EI KAKO Co., LTD.)
・ Non-woven: nikowipe clean room (NKB)
Use a soft cloth to clean the camera.
No.14S002-08
2 Warranty
■Warranty period
One year after delivery (However, the camera had malfunction with camera uses correctly)
In below case for a fee even within warranty period.
・The malfunction caused by incorrect usage, incorrect modify or repair.
・The malfunction caused by external shock including the camera dropping after delivery the camera.
・The malfunction caused by fire, earthquake, flood disaster, thunderbolt struck, other natural disaster or
wrong voltage.
■Warranty coverage
Exchange or repair the malfunction camera if the malfunction is occurred by our responsibility.
“Warranty” mean is warranty for the delivered camera itself. Please accept the induction damage by the
camera malfunction is not included.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
7/53
Page 8
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
3 Introduction
This document describes the specification of the following cameras:
STC-SBE132POE / STC-SCE132POE
3.1 Features
Support PoE (Power over Ethernet Support)
Maximum Frame Rate (Full Scanning): 61 fps @ 1.3M 8bits
CMOS (Global Shutter)
Defective Pixel Correction up to 64 points
8bits or 10bits output
3.2 Product Number Naming Method
No.14S002-08
STC-SxE132POE
POE: PoE (Power over Ethernet GigE)
132: 1.3M, 1/1.8” sensor
Sensor Manufacture
E: e2V
B: Monochrome
C: Color
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
8/53
Page 9
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
4 Specifications
4.1 Electronic Specifications
Model Number STC-SBE132POE STC-SCE132POE
Image Sensor 1/1.8” 1.3M Progressive Monochrome CMOS
(e2V: EV76C560)
Shutter Type Global / Rolling Shutter
Active Picture Elements 1,280 (H) x 1,024 (V)
Cell Size 5.3 (H) x 5.3 (V) µm
Sync Method
Maximum
Frame Rate
(at Full
scanning)
Image Output Format
Noise Level 8bits output Less than 3 digits (Gain 0 dB)
10bits / 10bits Packed output Less than 12 digits (Gain 0 dB)
Minimum Scene Illumination 0.6 Lux at F1.2 (Gain Max) 50 Lux at F1.2 (Gain Max)
Exposure 8bits output
Time 10bits / 10bits Packed output
RGB8 Packed output
Gain Analog
ROI
Multi ROIs N/A
Gamma
Binning
Decimation
Flip Image Horizontal / Vertical / Horizontal and vertical /
Pixel Blemish Correction
Auto Image
Control
Operational Mode
Communication UART communication through Ethernet port
Protocol IEEE802.3 (1000BASE-T)
Communication GigE Vision 1.2, GenICam 1.4
I/O One opt-isolated inputs and two open collector outputs (+3.3V)
Power Input Voltage +10.8 to +26.4 Vdc (IO Connector)
8bits output
10bits output 31 fps
10bits Packed output 42 fps
RGB8 Packed output N/A 21 fps
Mono8 / Mono10 / Mono10Packed
Digital
Horizontal: 32 to 1,280 pixels / Vertical: 32 to 1,024 lines (Default: 1,280 x 1,024)
Adjustable steps for image size: 8 pixels in horizontal direction / 2 lines in vertical direction
Adjustable steps for offset: 8 pixels in horizontal direction / 2 lines in vertical direction
Auto Exposure Support Support
Auto Gain (AGC) Support Support
Auto White Balance N/A Support
Power Consumption 12V: Less than 3.1 W / PoE: Less than 2.8 W
External trigger (Hardware / Software) / Free run
61 fps
10 µseconds to 1,000 seconds (Default: 16,379 µseconds)
0 to 5.38 dB (Default: 0)
0 to 9.51 dB (Default: 0)
Gamma 1.0 or uploadable gamma table
Horizontal: 1/2, Vertical: 1/2 / Off
Horizontal: 1/2, Vertical 1/2 / Horizontal 1/4, Vertical: 1/4 / Off
Off
Up to 64 points (Default: ON)
Edge Preset Trigger / Free run
or Power Over Ethernet (IEEE802.3af compliance)
1/1.8” 1.3M Progressive Color CMOS
(e2V: EV76C560)
Mono8 / Mono10 / Mono10Packed /
BayerRG8 / BayerRG10 /
BayerRG10Packed / RGB8Packed
Horizontal / Off
No.14S002-08
Default: Bold
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
9/53
Page 10
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
4.2 Spectral Sensitivity Characteristics
STC-SCE132POE / STC-SBE132POE
IF Cut Filter (STC-SCE132POE)
No.14S002-08
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
10/53
Page 11
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
4.3 Mechanical Specifications
Model Number STC-SBE132POE STC-SCE132POE
Dimensions 35 (W) x 35 (H) x 53.5 (D) mm (*1) 35 (W) x 35 (H) x 54.3 (D) mm (*1)
Optical Filter No Optical Filter No IR Cut Filter
Optical Center Accuracy Positional accuracy in Horizontal and Vertical directions: +/- 0.3 mm
Rotational accuracy of Horizontal and Vertical: +/- 2.0 deg.
Material Aluminum Alloy
Lens Mount C, mount, CS mount
Connectors RJ45 connector
Power- I/O connector: HR10A-7R-6PB (Hirose) or equivalent
Camera Mount Screws Two 1/4” Tripod screw holes (One on top and bottom plate)
Eight M4 screws holes (Four on top and bottom plate)
Weight Color: Approximately 100 g, Mono: Approximately 98 g
(*1) Excluding connectors
4.4 Environmental Specifications
Model Number STC-SBE132POE STC-SCE132POE
Operational
Temperature / Humidity
Storage Temperature / Humidity Environmental Temperature: -30 to +65 deg. C,
Vibration 20 Hz to 200 Hz to 20 Hz (1.3 Min. / cycle), acceleration 10 G, XYZ 3 directions 30 min. each
Shock Acceleration 38 G, half amplitude 6 mseconds, XYZ 3 directions 3 times each
Standard Compliancy EMS: EN61000-6-2, EMI: EN55011
RoHS RoHS Compliance
Minimum Environmental Temperature -5 deg. C
Maximum (*1) Camera housing temperature (top plate) shall not exceed +62 deg. C
(This corresponds to an environmental temperature of approximately +40 deg. C),
Environmental Humidity: 0 to 85 %RH (No condensation)
Environmental Humidity: 0 to 85 %RH (No condensation)
(*1) When the camera using under the condition that exceeds +40 deg. C environmental temperature, please insure the
camera installs with the appropriate heat dissipation to keep the housing temperature less than +62 deg. C.
If camera has a mounted lens and a tripod with an aluminum plate, this could decrease the camera housing
temperature for heat dissipation.
Taking these steps will maintain the heat rating of the electronic components of the camera.
Upper side of camera
Measuring point
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
11/53
Page 12
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
5 Connector Specifications
5.1 RJ45 Connector
This product is PoE compliant. Please supply power (+10.8 to +26.4 Vdc) through the power-I/O connector
when using non-PoE-compliant NIC.
Please use a 1GB supported NIC, Network Switcher and LAN cable. Check that the NIC and Network
Switcher being used is “1GB transferring”.
Power-I/O Connector
Pin Assignment LED
Pin No. Signal Name
1 TA+
2 TA3 TB+
4 TC+
5 TC6 TB7 TD+
8 TD-
Camera is powered-on
Green Light ON Yellow Light ON Power ON(1GB NIC)
Green Light OFF Yellow Light OFF Power ON(100MB NIC)
Green Light ON Yellow Light Blinking 1Gb Transferring
Light OFF Yellow Light Blinking 100 Mb Transferring
Green LED
Yellow LED
RJ45 Connector
Green LED Yellow LED Status
Green light: ON
Orange light: Blinking
1 GB Transferring
Green light: OFF
Yellow light: Blinking
100 MB Transferring
No.14S002-08
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
12/53
Page 13
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
5.2 Power / IO Control Signal Connector
HR10A-7R-6PB (Hirose)r equivalent
This connector is for the power supply (12Vdc) and input /output signals.
Use HR10A-7P-6S (Hirose) or equivalent for the cable side.
Pin assignment
No.14S002-08
Pin No. Signal Name
1 GND IN 0 V
2 I/O-1 OUT +3.3 V Open Collector
3 I/O-2 OUT +3.3 V Open Collector
4
5
6 POWER IN IN +10.8 to +26.4 Vdc
Configuration of I/O-1(Pin No.2) and I/O-2(Pin No.3)
Output pin can be assigned through register setting or GenICam Command.
TRG_In-
(Opt. Isolated -)
TRG_In+
(Opt. Isolated +)
IN /
OUT
IN
IN
I/O-1 (Pin No.2) / I/O-2 (Pin No.3)
1) FrameTriggerWait (initial setting for I/O-1)
2) UserOutput
3) ExposureActive (initial setting for I/O-2)
4) TriggerAuxiliary
5) TriggerInternal
6) SensorReadOut
7) StrobeSignal
Low: Smaller than +1.0 V
High: +3.0 to +26.4 V
* potential difference between TRG_Inand TRG_In+
GenICam command
Voltage
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
13/53
Page 14
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
1) FrameTriggerWait
The user can check the camera condition (camera exposure and image output processing by the
trigger signal with this FrameTriggerWait signal).
This signal is LOW for the period from the trigger input signal to the image output.
2) UserOutput
The status of the UserOutput signal can change with the “UserOutputValue”.
3) ExposureActive
The user can check the exposure time with the ExposureActive signal.
4) TriggerAuxiliary
The TriggerAuxiliary signal is the input trigger signal.
5) TriggerInternal
The TriggerInternal signal is the input trigger signal with the trigger delay time.
6) SensorReadOut
The SensorReadOut signal is the FVAL signal, which is the image output period of the time.
7) StrobeSignal
The StrobeSignal signal is the strobe control signal.
No.14S002-08
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
14/53
Page 15
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Equivalent Circuit for the Input Pin of the I/O Connector
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
15/53
Page 16
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Typical Input Circuit
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
No.14S002-08
16/53
Page 17
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Typical Output Circuit
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
No.14S002-08
Note:
Value of Vcc and
Pull up register can be
set within the spec of
transistor.
17/53
Page 18
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Input and Output Signal Timing (Hardware Trigger)
Case of “External Hardware Trigger”, “Positive Edge Trigger”, “Edge Preset Exposure”,
Camera internal processing
External hardware
trigger
Photocoupler output
Filtering
Trigger delay
No.14S002-08
Up to 15us
For the signal duration, refer to another chapter "Exposure".
TriggerDelay on GenICam
For the signal duration, refer to another chapter "Exposure".
Exposure
Video output
Output Signal
FrameTriggerWait
ExposureActive
TriggerAuxiliary
TriggerInternal
SensorReadOut
StrobeSignal
ExposureTimeRaw on GenICam
StrobeSignalDelay on GenICam
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
StrobeSignalOnTime on GenICam
18/53
Page 19
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Input and Output Signal Timing (Software Trigger)
Case of “Software Trigger”, “Positive Edge Trigger”, “Edge Preset Exposure”,
Camera internal processing
Software trigger,PLC
and Command
Trigger delay
Exposure
No.14S002-08
TriggerDelay on GenICam
For the signal duration, refer to another chapter "Exposure".
ExposureTimeRaw on GenICam
Video output
Output Signal
FrameTriggerWait
ExposureActive
TriggerAuxiliary
TriggerInternal
SensorReadOut
StrobeSignal
StrobeSignalDelay on GenICam
StrobeSignalOnTime on GenICam
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
19/53
Page 20
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
6 Dimensions
6.1 STC-SBE132POE
6.2 STC-SCE132POE
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
No.14S002-08
Unit:mm
Unit:mm
20/53
Page 21
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
7 Sensor information
7.1 Pixel Transferring Image
STC- SBE132POE (Monochrome)
STC- SCE132POE (Color)
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
Pixel1 of
Data
Pixel11 of
Data
Pixe21 of
Data
Pixel2 of
Data
Pixel12 of
Data
Pixel22 of
Data
Pixel (m, n) of Data: nth pixel of the mth line being transferred
No.14S002-08
Pixel (n) of Data: nth pixel being transferred
21/53
Page 22
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
8 Camera Operational Modes
8.1 Normal Mode (TriggerMode = Off)
S e n s o r
E x p o s u r e
I m a g e o u t
8.2 Edge Preset Trigger Mode (ExposureMode = Timed)
In this “edge preset trigger mode”, the camera exposure starts at the rising edge of the trigger signal like the “pulse
width trigger mode” in the previous sections. However, in this mode, the exposure duration time is based on the preset
value stored by the by the camera setting communication. When Trigger input during exposure time or video out period,
Trigger signal is ignored. Please input the trigger signal without this period.
Timing
Trigger Input (Positive)
Note 1: The exposure time is set by the preset electronic shutter speed.
Exposure Time
Image Out
E x p o s u r e
T i m e
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
22/53
Page 23
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Exposure Timing with the Positive Polarity Trigger Signal
Note 1: The trigger signal will be removed by the filtering if the pulse width of the input trigger signal is less than 60 CLK.
Note 2: The exposure will start 10us after the rising edge of the trigger signal.
(With Photocoupler delay
Note 1: The trigger signal will be removed by the filtering if the pulse width of the input trigger signal is less than 60 CLK.
Note 2: The exposure will start 10us after the rising edge of the trigger signal.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
Input Trigger signal
Trigger signal
(With Photocoupler delay
Filtering *Note.1
Less than
15useconds
Exposure time
Please input a trigger signal with more than 61 CLK pulse width.
Exposure Timing with the Negative Polarity Trigger signal
60 CLK
10us
Input Trigger signal
Trigger signal
Filtering *Note.1
Less than
60 useconds
Exposure time
Please input a trigger signal with more than 61 CLK pulse width.
60 CLK
10us
T1'
Exposure tim: T1' = Preset exposure time
T1'
Exposure tim: T1' = Preset exposure time
23/53
Page 24
1st ROW
(Camer a to PC)
1st ROW
(Camera to PC)
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
8.3 CMOS Rest Type
With this camera, you can select the sensor exposure type as either "Electronic Rolling Shutter (ERS)" or
"Global Reset (GR)".
Electronic Rolling Shutter(ERS)
Trigge r Input
Exposure in Rolling Shut ter mode
(in Camera)
Exposure Start Delay
2nd ROW
Last ROW
Exposure Time
intern al
delay
No.14S002-08
・
・
・
Data Tx
Global Shutter (for EdgePreset) Note: This function works on Trigger-mode
Trigge r Input
Exposure Time
Exposure in Global Shu tte r
(in Cam era)
Exposure Start Delay
2nd ROW
Last ROW
Data Tx
・
・
・
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
24/53
Page 25
Width
OffsetX
OffsetY
ROI area
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9 Camera Functions
9.1 ROI (Region of Interest)
The specified area of the image can output from the camera with ROI function.
The frame rate is increased when the height is reduced.
The frame rate does not increase when the width is reduced.
ROI (1 region)
GenICamparamters
Width Integer type Width of the output image (pixels)
(Width + OffsetX) should not exceeded maximum width.
Height Integer type Height of the output image (lines)
(Height + OffsetY) should not exceeded maximum height.
OffsetX Integer type Horizontal (pixel) offset
Default: 0, Adjustable steps: 8 pixels
OffsetY Integer type Vertical (line) offset
Default: 0,
Adjustable steps: 2 liens
The ROI area settings are below:
No.14S002-08
Height
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
25/53
Page 26
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Width / Height setting range
No.14S002-08
STC-SBE132POE
STC-SCE132POE
Width Range 32 to 1,280 pixels
Default 1,280 pixels
Adjustment steps 8 pixels
Height Range 32 to 1,024 lines
Default 1,024 lines
Adjustment steps 2 lines
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
26/53
Page 27
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.2 Pixel Format
The image format from camera can be set on the Pixel Format.
GenICam Parameters
PixelFormat IEnumeration Type Pixel Format
The following chart shows the available Pixel Formats on the camera:
Output Bit Pixel Format
Monochrome Camera Color Camera
8bits Mono8 Mono8 / BayerRG8
10bits Mono10 Mono10 / BayerRG10
10bits Packed Mono10Packed Mono10Packed / BayerRG10Packed
RGB8Packed N/A RGB8Packed
Each format specified on GenICam PFNC (Pixel Format Naming Convention).
9.3 Binning
Binning is add and average beside pixels into one pixel.
The pixel data inside of red square add or average as one pixel.
X(Off), Y(Off)
Binning
Binning X(Off), Y(On)
No.14S002-08
Binning X(On), Y(Off) Binning X(On), Y(On)
GenICamParameters
BinningHorizontal Integer Type Sets Binning on Horizontal direction
1: Disable Binning 2: Binning 2 Pixel
BinningVertical Integer Type Sets Binning on Vertical direction
1: Disable Binning 2: Binning 2 Pixel
(*) Binning and Decimation function cannot be use simultaneously.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
27/53
Page 28
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.4 Decimation
When using Decimation mode, the decimated image can be output.
The images below show decimated pixels (red squares) where they are output.
Decimation X(Off), Y(Off)
Decimation X(Off), Y(Off)
Decimation X(Off), Y(On)
Decimation X(Off), Y(On)
No.14S002-08
Decimation X(On), Y(Off) Decimation X(On), Y(On)
Decimation X(On), Y(Off) Decimation X(On), Y(On)
GenICam Parameters
DecimationHorizontal Integer Type Sets decimation on horizontal direction
1: Disable Decimation, 2: Decimate one of two pixels
4: Decimate three of four pixels
DecimationVertical Integer Type Sets decimation on vertical direction
1: Disable Decimation, 2: Decimate one of two pixels
4: Decimate three of four pixels
(*) Binning and Decimation function cannot be use simultaneously.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
28/53
Page 29
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.5 Image Flip
Flip the image through ReverseX and ReverseY.
GenICam Parameters
ReverseX IBoolean Type Switch ON / OFF at Horizontal
False: Horizontal Flip Off, True: Horizontal Flip On. Default: False
ReverseY IBoolean Type Switch ON / OFF at Vertical
False: Vertical Flip Off, True: Vertical Flip On. Default: False
No.14S002-08
Reverse X(Off), Y(Off)
00 01 02 03
10 11 12 13
20 21 22 23
30 31 32 33
Reverse X(On), Y(Off)
Reverse X(Off), Y(On)
30 31 32 33
20 21 22 23
10 11 12 13
00 01 02 03
Reverse X(On), Y(On)
00010203
10111213
20212223
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
30313233
30313233
20212223
10111213
00010203
29/53
Page 30
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Reverse X(Off), Y(Off)
00 01 02 03
10 11 12 13
20 21 22 23
30 31 32 33
Reverse X(On), Y(Off)
Reverse X(Off), Y(On)
30 31 32 33
20 21 22 23
10 11 12 13
00 01 02 03
Reverse X(On), Y(On)
00010203
10111213
20212223
(*) When the image is flipping for color camera, the pixel array is also flipped.
30313233
30313233
20212223
10111213
00010203
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
30/53
Page 31
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.6 Gain
The analog gain and the digital gain are available for the gain control.
Analog gain
This parameter sets the analog gain.
GenICam parameter
Gain Float type Analog gain.
Range: 0 to 208, Default: 0
Analog gain formula
Gain (dB) = Gain / 10
Digital gain
This parametersets the digital gain.
GenICam parameter
DigitalGain Integer type Digital gain.
Range: 0 to 255, Default: 0
Digital gain formula
Gain (xtimes) = 1+ (DigitalGain / 128)
9.7 Black level
This parameter sets the black level (the clamp level for the black signal).
The bottom of the signal is clamped at this setting level. The signal does not become below this level.
GenICam parameter
BlackLevel Float type Black level.
Range: 0 to 20, Default: 10
Black level formula
At 10bits output: Black level (grayscale) = BlackLevel
At 8bits output: Black level (grayscale) = BlackLevel / 4
No.14S002-08
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
31/53
Page 32
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.8 ALC (Auto Light Control)
ALC function has two control methods, which is AGC (Auto Gain Control) and the auto shutter. The AGC and the auto
shutter sets up individually.
The camera parameters are adjusted to the brightness of the image is maintained with the target brightness
automatically with the ALC function.
GenICam parameters (for AGC and auto shutter)
TargetBrightness Integer type Target brightness.
Range: 0 to 255, Default: 128
ACL_Peak_Average Integertype Importance ratio for the brightness peak at ALC control.
Range: 0 to 255, Default: 0
ALCWeight1
ALCWeight2
ALCWeight3
ALCWeight4
ALCWeight5
ALCWeight6
ALCWeight7
ALCWeight8
ALCWeight9
ALCWindowV1
ALCWindowV2
ALCWindowV3
ALCWindowV4
Integer type Weight.
Range: 0 to 15, Default: 1 * Set 10 on ALCWeight5 only
Sets the weight for each weight area.
Integer type Vertical positions for the frame of the weight area.
Range: 0 to 1,023
Default: V1 (32), V2 (373), V3 (651), V4 (992)
ALCWindowH1
ALCWindowH2
ALCWindowH3
ALCWindowH4
Target brightness (TargetBrightness) formula
At 10bits output: Target brightness (grayscale) = TargetBrightness x 4
At 8bits output: Target brightness (grayscale) = TargetBrightness
About the importance ratio for the brightens peak at ALC control (ACL_Peak_Average)
When 0 sets, Average: 100 %, Peak: 0 %. The ALC control with the brightness average.
When 255 sets, Average: 0 %, Peak: 100 %. The ALC control with the brightness peak.
When 128 sets, Average: 50 %, Peak: 50 %.
Integer type Horizontal positions for the frame of the weight area.
範囲: 0 to 1,279
初期値: H1 (36), H2 (462), H3 (818), H4 (1,244)
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
32/53
Page 33
No.14S002-08
ALCWindowV1
ALCWindowV2
ALCWindowV3
ALCWindowV4
ALCWindowH4
ALCWindowH3
ALCWindowH2
ALCWindowH1
Area1
Area2
Area3
Area4
Area5
Area6
Area7
A
rea8
Area9
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
ALC control method
The ALC control with the weight area1 to 9.
The weight area setting parameters are in below:
The brightness average and peak calculate for each weight area.
The target brightness comparison value calculates with “ALC_Peak_Average”, the brightness average and peak then
compare with the target brightness to define the necessary brightness control (to dark or to bright).
The brightness of the image maintains to the “TargetBrightness” with the AGC and the auto shutter functions.
If AGC and the auto shutter are ON for the ALC control, the auto shutter function maintains the brightness first. The AGC
function maintains the brightness if the brightness cannot maintain to the TargetBrightness with the auto shutter.
AGC (Auto Gain Contorl)
The brightness of the image maintains to the target brightness with the gain automatically.
If the brightness of the image is the darker than the target brightness, the gain increases up to AGCRange.
If the brightness of the image is the brighter than the target brightness, the gain decreases.
GenICam parameters
GainAuto Enumeration type AGC ON / OFF selection
AGCRange Integer type Maximum gain.
Selection: ON (Continuous) or OFF (Off). Default: OFF
Range: 0 to 63, Default: 63
This is the maximum gain for AGC.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
33/53
Page 34
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Auto shutter
The brightness of the image maintains to the target brightness with the shutter automatically.
If the brightness of the image is the darker than the target brightness, the exposure time extends up to
Max_ShutterTime.
If the brightness of the image is the brighter than the target brightness, the exposure time becomes shorter up to
Min_ShutterTime.
GenICam parameters
ExposureAuto Enumeration
type
Min_ShutterTime Integer type Minimum exposure time (µsecond).
Max_ShutterTime Integer type Maximum exposure time (µsecond).
ALC settings procedure
ALC settings procedure
1. Sets ALCWeight1 to 9.
2. Sets ALCWindowV1 to 4.
3. Sets ALCWindowH1 to 4.
4. Sets TargetBrightness.
5. Sets ACL_Peak_Average.
6. Sets AGCRange if AGC is using.
7. Sets Min_ShutterTime, if the auto shutter is using.
8. Sets Max_ShutterTime, if the auto shutter is using.
9. Sets “Continuous” at GainAuto, if AGC is using.
10. Sets “Continuous” at ExposureAuto, if the auto shutter is using.
Auto shutter ON / OFF selection
ON (Continuous), OFF (Off). Default: OFF
Range: 10 to 1,000,719 Default: 10
Range: 10 to 1,000,719 Default: 16,379
No.14S002-08
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
34/53
Page 35
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.9 White balance (Only available for the color cameras)
The color compensates with the gain adjustment each color.
The gain for each color has to adjust with the flat white target to each color has the same brightness.
The white balance control methods are the listed in the below:
OFF
Auto white balance
Push to set white balance
Preset1 to 3
White balance control methods
GenICam parameters
BalanceWhiteAuto Enumeration
type
BalanceRatioSelector Enumeration
type
BalanceRatio Float type Color gain setting for the color selects at BalanceRatioSelector
YThreshold Integer type The brightness threshold to use the pixel for the auto white
BalanceRatio_R_Once Integer type R white balance gain for OFF and push to set white balance.
BalanceRatio_Gr_Once Integer type GR white balance gain for OFF and push to set white balance.
BalanceRatio_B_Once Integer type R white balance gain for OFF and push to set white balance.
BalanceRatio_Gb_Once Integer type Gb white balance gain for OFF and push to set white balance.
BalanceRatio_R_Preset1 Integer type R white balance gain for preset1.
BalanceRatio_Gr_Preset1 Integer type Gr white balance gain for preset1.
BalanceRatio_B_Preset1 Integer type B white balance gain for preset1.
BalanceRatio_Gb_Preset1 Integer type Gb white balance gain for preset1.
BalanceRatio_R_Preset2 Integer type R white balance gain for preset2.
BalanceRatio_Gr_Preset2 Integer type Gr white balance gain for preset2.
BalanceRatio_B_Preset2 Integer type B white balance gain for preset2.
BalanceRatio_Gb_Preset2 Integer type Gr white balance gain for preset2.
White balance control method selection. Default: off
White balance control target color selection.
balance control.
Default: 0,Range: 0 to 4,095
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
No.14S002-08
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
35/53
Page 36
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
GenICam parameters
BalanceRatio_R_Preset3 Integer type R white balance gain for preset3.
Default: 0
BalanceRatio_Gr_Preset3 Integer type Gr white balance gain for preset3.
Default: 0
BalanceRatio_B_Preset3 Integer type B white balance gain for preset3.
Default: 0
BalanceRatio_Gb_Preset3 Integer type Gb white balance gain for preset3.
Default: 0
OFF
The white balance with BalanceRatio_X_Once (X: R, Gr, B or Gb)
If the white balance process is not necessary, please sets 0 for BalanceRatio_X_Once (X: R, Gr, B orGb)
White balance “OFF” setting procedure
1. Sets Off at BalanceWhiteAuto.
Auto white balance
The optimized white balance gain calculates each frame for the auto white balance.
Auto white balance setting procedure
1. Sets Continuous at BalanceWhiteAuto.
Push to set white balance
The white balance gain adjusts once after select this white balance then set to Balance_X_Once (X: R, Gr, B or Gb)
Sets OFF at BalanceWhiteAuto automatically after set Balance_X_Once.
Push to set white balance setting procedure
1. Sets the flat white target.
2. Sets Once at BalanceWhiteAuto.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
36/53
Page 37
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Preset white balance1 to 3
The camera has three preset manual white balance.
Presets saving area
Preset1: BalanceRatio_R_Preset1,BalanceRatio_Gr_Preset1,
BalanceRatio_B_Preset1,BalanceRatio_Gb_Preset1
Preset2: BalanceRatio_R_Preset2,BalanceRatio_Gr_Preset2,
BalanceRatio_B_Preset2,BalanceRatio_Gb_Preset2
Preset3: BalanceRatio_R_Preset3,BalanceRatio_Gr_Preset3,
BalanceRatio_B_Preset3,BalanceRatio_Gb_Preset3
Preset white balance setting procedure
1. Sets the white balance gain for the preset1, 2 or 3. (X: 1 to 3)
(BalanceRatio_R_PresetX, BalanceRatio_Gr_PresetX,BalanceRatio_B_PresetX,BalanceRatio_Gb_PresetX)
2. Sets PresetX (X: 1 to 3) at BalanceWhiteAuto.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
37/53
Page 38
WB_WindowV1
WB_WindowV2
WB_WindowH2
WB_WindowH1
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
White balance calculate area setting
The white balance gain calculation area is changeable.
GenICam parameters
WB_WindowMode Enumeration
type
WB_WindowV1
WB_WindowV2
WB_WindowH1
WB_WindowH2
The brightness threshold for the white balance gain calculate pixel (YThreshold)
Threshold (grayscale) ＝YThreshold
12bits process in the camera.
The white balance calculation area settings are below:
Integer type Vertical frame position for the specified area.
Integer type Horizontal frame position for the specified area.
White balance gain calculation area selection
Full screen (Off), Specified area (On). Default: Full screen
Range: 0 to 1,023
Default: V1 (0), V2 (1,023)
Range: 0 to 1,279
Default: H1 (0), H2 (1,279)
No.14S002-08
White balance gain
calculation area
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
38/53
Page 39
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.10 Gamma correction
The gamma correction is the gamma = 1.0 or the gamma table control.
GenICam parameters
GammaMode Enumeration
type
ReloadGammaData Command type Gamma table loading from ROM to RAM
Gamma table loading procedure (ReloadGammaData)
1. Executes ReloadGammaData.
Gamma table writing
It is necessary to use the virtual com port communication (eBUS SDK: PvSerialPort class) to write the gamma table to
the camera. The gamma table cannot write the camera with GenICam parameter.
Please refer the other document for the details of the gamma table writing.
Gamma correction selection
Gamma = 1.0 (Off), Gamm table control (On). Default: Gamma =
1.0
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
39/53
Page 40
Selector
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.11 Save and load the camera setting data
The camera has the camera setting including the factory default, load function.
The camera has below two camera settings.
Default: The factory default settings (This setting cannot change)
User Set X: Over writeable camera settings (X: 0 to 7)
These camera settings load from ROM to the register in the RAM on the camera and camera settings save to ROM.
The camera settings saving and loading is controllable with Parameters (User Set Selector, User Set Default), and
commands (UserSetLoad, UserSetSave) in UserSetControl category of GenICam.
The details of the parameters and the functions are in the table below:
GenICam Parameters
UserSetSelector IEnumeration Type Select “Default” or ”UserSetX”
UserSetLoad or UserSetSave process for the selected settings.
UserSetLoad ICommand Type The camera settings load from ROM to the register in RAM.
UserSetSave ICommand Type The camera settings at the register in RAM save to ROM.
UserSetDefault IEnumeration Type Select which settings (“Default or UserSet X) load automatically when the
camera power is on. This selection saves automatically.
Saving the Camera Settings
Camera
Setting
UserSetSelector
Setting Procedure
1. Selects “UserSetX” at “UserSetSelector”
2. Execute “UserSetSave”
ROM
UserSetX
ROM
Default
When UserSetSave is executing,
the camera settings at the register in RAM
are saved to the ROM that is selected at
UserSetSelector.
Caution:
UserSetSave cannot execute when “Default”
was selected at “UserSet Selector”
No.14S002-08
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
40/53
Page 41
No.14S002-08
Selector
Selector
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Loading Camera Settings
ROM
UserSetX
Camera
Setting
ROM
Default
UserSetSelector
Setting Procedure
1. Select “UserSetX” (or Default) at “UserSetSelector”
2. Execute “UserSetLoad”
Loading Camera Settings when the Camera Power is on
ROM
UserSetX
Camera
Setting
ROM
Default
UserSetSelector
Setting Procedure
1. Set “UserSetX” or “Default” at “UserSetDefault”
Camera Settings Initialization
Please follow the below procedure for the camera settings put back to the factory default settings.
Setting Procedure
1. Selects “Default” at “UserSetSelector”.
2. Executes “UserSetLoad”.
3. Select “UserSet1” at “UserSetSelector”.
4. Executes “UserSetSave”.
When UserSetLoad is executing,
the camera settings load from the selected
ROM that was selected at “UserSetSelector”
to the register at RAM.
When the camera power is on,
the camera settings load from the selected
ROM that was selected at “UserSetDefault”
to the register at RAM.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
41/53
Page 42
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.12 Trigger
No.14S002-08
The description of trigger type and characteristic, please refer to the chapter “Image acquisition and Camera
Mode”.
Trigger Signal Processing Process
External Hardware Trigger or Software Trigger input the camera’s internal process as follows.
Switching Trigger can be done through register access or GenICam commands
Switching point 1: Switch to Hardware Trigger and Software Trigger
TriggerSource = Software on GenICam
TriggerSource = Hardware on GenICam
TriggerSource = Line0 on GenICam
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
42/53
Page 43
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.13 The camera settings (GenICam parameters) control with SDK
GenICam parameters are controllable with the eBUS SDK.
Please refer eBUS SDK API help file for the details.
Integer type parameter control
Integer type parameter such as “Width” control.
e.g. Width writing
[C++] PvDevice.GetGenParameters()->SetIntegerValue(“Width”, 256);
[C#】 PvDevice.GenParameters.SetIntegerValue(“Width”, 256);
e.g. Width reading
[C++] PvDevice.GetGenParameters()->GetIntegerValue(“Width”, &intValue);
[C#] intValue = PvDevice.GenParameters.GetIntegerValue(“Width”);
Float type parameter control
Float type parameter such as “AcquisitionFrameRate” control.
e.g. AcquisitionFrameRate writing
[C++] PvDevice.GetGenParameters()->SetFloatValue(“AcquisitionFrameRate”, 33.3);
[C#] PvDevice.GenParameters.SetFloatValue(“AcquisitionFrameRate”, 33.3);
e.g. AcquisitionFrameRate reading
[C++] PvDevice.GetGenParameters()->GetFloatValue(“AcquisitionFrameRate”, &doubleValue);
[C#] doubleValue = PvDevice.GenParameters.GetFloatValue(“AcquisitionFrameRate”);
Enumeration type parameter control
Enumeration type parameter such as “BalanceWhiteAuto” control.
e.g. BalanceWhiteAuto writing
[C++] PvDevice.GetGenParameters()->SetEnumValue(“BalanceWhiteAuto”, “Continuous”);
[C#] PvDevice.GenParameters.SetEnumValue(“BalanceWhiteAuto”, “Continuous” );
e.g. BalanceWhiteAuto reading
[C++] PvDevice.GetGenParameters()->GetEnumValue(“BalanceWhiteAuto”, &PvStringValue);
[C#] stringValue = PvDevice.GenParameters.GetEnumValueAsString(“BalanceWhiteAuto”);
No.14S002-08
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
43/53
Page 44
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
String type paramter control
String type parameter such as “DeviceModelName” control.
e.g.DeviceModelName writing (DeviceModelName cannot overwrite)
[C++] PvDevice.GetGenParameters()->SetString(“DeviceModelName”, “STC-SB33POE”);
[C#] PvDevice.GenParameters.SetStringValue(“DeviceModelName”, “STC-SB33POE”);
e.g. DeviceModelName reading
[C++] PvDevice.GetGenParameters()->GetString(“DeviceModelName”, &PvStringValue);
[C#] stringValue = PvDevice.GenParameters.GetStringValue(“DeviceModelName”);
Boolean type parameter control
Boolean type parameter such as “LineInverter0” control.
e.g. LineInverter0 writing
[C++] PvDevice.GetGenParameters()->SetBooleanValue(“LineInverter0”, true);
[C#] PvDevice.GenParameters.SetBooleanValue(“LineInverter0”, true);
e.g. LineInverter0 reading
[C++] PvDevice.GetGenParameters()->GetBooleanValue(“LineInverter0”, &boolValue);
[C#] boolValue = PvDevice.GenParameters. GetBooleanValue(“LineInverter”);
Command type paramter control
Command type parameter such as “TriggerSoftware”
e.g. TriggerSoftware generating
[C++] PvDevice.GetGenParameters()->ExecuteCommand(“TriggerSoftware”);
[C#] PvDevice.GenParameters.ExexuteCommand(“TriggerSoftware”);
No.14S002-08
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
44/53
Page 45
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
9.14 GenICam Command List
DeviceControl
Name Description
DeviceVendorName Name of the manufacturer of the device.
DeviceModelName Model of the device.
DeviceManufacturerInfo Manufacturer information about the device.
DeviceVersion Version of the device.
DeviceID Device's serial number.
DeviceUserID User-programmable device identifier.
DeviceScanType Scan type of the sensor of the device.
DeviceTemperature Device temperature in degrees Celsius (C).
DeviceReset Reset the device to its power up state.
ImageFormatControl
Name Description
SensorDigitizationTaps Number of digitized samples outputted simultaneously by the camera A/D conversion
stage.
Width Width of the image provided by the device (in pixels).
Height Height of the image provided by the device (in pixels).
SensorShutterMode Sets the shutter mode of the device.
DecimationHorizontal Horizontal sub-sampling of the image. This reduces the horizontal resolution (width) of
the image by the specified horizontal decimation factor.
DecimationVertical Vertical sub-sampling of the image. This reduces the vertical resolution (height) of the
image by the specified vertical decimation factor.
RegionSelector Selects the Region of interest to control. The RegionSelector feature allows devices that
are able to extract multiple regions out of an image, to configure the features of those
individual regions independently.
ReverseX This feature is used to flip horizontally the image sent by the device. The AOI is applied
after the flipping.
ReverseY This feature is used to flip vertically the image sent by the device. The AOI is applied
after the flipping.
PixelFormat Format of the pixels provided by the device. It represents all the information provided by
PixelCoding, PixelSize, PixelColorFilter combined in a single feature.
PixelCoding Coding of the pixels in the image, Raw gives the data in the native format of the sensor.
PixelSize Total size in bits of a pixel of the image.
PixelColorFilter Type of color filter that is applied to the image.
TestImageSelector Selects the type of test image that is sent by the camera.
OffsetX Horizontal offset from the origin to the region of interest (in pixels).
OffsetY Vertical offset from the origin to the region of interest (in pixels).
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
45/53
Page 46
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
AcquisitionControl
Name Description
AcquisitionMode Sets the acquisition mode of the device. It defines mainly the number of frames to
capture during an acquisition and the way the acquisition stops.
AcquisitionStart Starts the Acquisition of the device. The number of frames captured is specified by
AcquisitionMode.
AcquisitionStop Stops the Acquisition of the device at the end of the current Frame. It is mainly used
when AcquisitionMode is Continuous but can be used in any acquisition mode.
AcquisitionFrameCount Number of frames to acquire in MultiFrame Acquisition mode.
AcquisitionFrameRate Controls the acquisition rate (in Hertz) at which the frames are captured.
TriggerSelector Selects the type of trigger to configure.
TriggerMode Controls if the selected trigger is active.
TriggerSoftware Generates an internal trigger. TriggerSource must be set to Software.
TriggerSource Specifies the internal signal or physical input Line to use as the trigger source. The
selected trigger must have its TriggerMode set to On.
TriggerActivation Specifies the activation mode of the trigger.
TriggerDelay Specifies the delay in microseconds (us) to apply after the trigger reception before
activating it.
ExposureMode Sets the operation mode of the Exposure (or shutter).
ExposureTime Sets the Exposure time when ExposureMode is Timed and ExposureAuto is Off. This
controls the duration where the photosensitive cells are exposed to light.
ExposureTimeAbs Sets the Exposure time when ExposureMode is Timed and ExposureAuto is Off. This
controls the duration where the photosensitive cells are exposed to light.
ExposureTimeRaw Sets the Exposure time when ExposureMode is Timed and ExposureAuto is Off. This
controls the duration where the photosensitive cells are exposed to light.
ExposureAuto Sets the automatic exposure mode when ExposureMode is Timed. The exact algorithm
used to implement this control is device-specific.
DigitalIOControl
Name Description
LineDebounceTime Sets the value of the input line debouncer time.
LineSource0 Set the output signals from the power / IO connector.
LineSource1 Set the output signals from the power / IO connector.
UserOutputValue0 Sets the value of the bit selected by LineSource0.
UserOutputValue1 Sets the value of the bit selected by LineSource1.
StrobeSignalDelay Specifies the delay in microseconds (us) to apply the trigger reception before activating
strobe signal.
StrobeSignalOnTime Specifies the strobe signal active time in microseconds (us).
LineInverter0 Controls the invertion of the signal of the selected output line of LineSource0.
LineInverter1 Controls the invertion of the signal of the selected output line of LineSource1.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
46/53
Page 47
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
CounterAndTimerControl
Name Description
CounterSelector Selects which Counter to configure.
CounterEventSource Select the events that will be the source to increment the Counter.
ConterDecrementEventSource Selects the event that decrements the counter.
CounterResetSource Selects the signals that will be the source to reset the Counter.
CounterResetActivation Selects the Activation mode of the Counter Reset Source signal.
CounterValue Reads or writes the current value of the selected Counter.
CounterDuration Sets the duration (or number of events) before the CounterEnd event is generated.
CounterStatus Returns the current status of the Counter.
CounterTriggerSource Selects the source to start the Counter.
TimerSelector Selects which Timer to configure.
TimerDurationRaw It sets the duration in device-specific unit of the Timer pulse.
TimerDelayRaw It sets the duration in device-specific unit of the delay to apply after the reception of a
trigger before start the Timer.
TimerTriggerSource Selects the source of the trigger to start the Timer.
TimerTriggerActivation Selects the activation mode of the trigger to start the Timer.
TimerGranularityFactor Controls the granularity of the TimerDurationRaw and TimerDelayRaw features (in
increments of up to 30 nseconds).
TimerPeriod Returns the period, in ns, of the selected timer.
TimerFrequency Returns the frequrency, in Hertz, of the selected timer.
EventControl
Name Description
PLC Category that contains the PLC event features.
IPEngineCamHeadSerialComLog Category that contains the IP engine to camera head serial communication log event
features.
EventSelector Selects which Event to signal to the host application.
EventNotification Activate or deactivate the notification to the host application of the occurrence of the
selected Event.
AnalogControl
Name Description
GainSelector Selects which Gain is controlled by the various Gain features.
Gain Controls the selected gain as an absolute physical value. This is an amplification factor
applied to the video signal.
GainRaw Controls the selected gain as an absolute physical value. This is an amplification factor
applied to the video signal.
GainAbs Controls the selected gain as an absolute physical value. This is an amplification factor
applied to the video signal.
GainAuto Sets the automatic gain control (AGC) mode. The exact algorithm used to implement
AGC is device-specific.
BlackLevelSelector Selects which Black Level is controlled by the various Black Level features.
BlackLevel Controls the black level as an absolute physical value. This represents a DC offset
applied to the video signal.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
47/53
Page 48
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
TransportLayerControl
Name Description
PayloadSize Provides the number of bytes transferred for each image or chunk on the stream
channel.
GevVersionMajor Major version of the specification.
GevVersionMinor Minor version of the specification.
GevVDeviceModeIsBigEndian Endianess of the device registers.
GevDeviceClass Returns the class of the device.
GevDeviceModeCharacterSet Character set used by all strings of the bootstrap registers.
GevIntefaceSelector Selects which physical network interface to control.
GevMACAddress MAC address of the network interface.
GevSupportedOptionSelector Selects the GEV option to interrogate for existing support.
GevSupportedOption Returns if the selected GEV option is supported.
GevCurrentIPContfigurationLLA Controls whether the Link Local Address IP configuration scheme is activated on the
given network interface.
GevCurrentIPConfigurationDHCP Controls whether the DHCP IP configuration scheme is activated on the given network
interface.
GevCurrentIPConfigurationPersistent Controls whether the Persistent IP configuration scheme is activated on the given
network interface.
GevCurrentIPAddress Reports the IP address for the given network interface.
GevCurrentSubnetMask Reports the subnet mask of the given network interface.
GevCurrentDefaultGateway Reports the default gateway IP address to be used on the given network interface.
GevIPConfigurationStatus Reports the current IP configuration status.
GevFirstURL Indicates the first URL to the XML device description file.
GevSecondURL Indicates the second URL to the XML device description file.
GevNumberOfInterface Indicates the number of physical network interfaces supported by this device.
GevPersistentIPAddress Controls the Persistent IP address for this network interface.
GevPersistentSubnetMask Controls the Persistent subnet mask associated with the Persistent IP address on this
network interface.
GevPersistentDefaultGateway Controls the Persistent default gateway for this network interface.
GevMessageChannelCount Indicates the number of message channels supported by this device.
GevStreamChannelCount Indicates the number of stream channels supported by this devices.
GevHeatrtbeatTimeout Controls the current heartbeat timeout in miliseconds.
GevTimestampCounterSelector Selects the source counter for GigE Vision timestamps.
GevTimestampSetSource Selects the signal that sets the counter to GevTimestampValueAtSet.
GevTimestampSetActivation Selects the activation mode for the counter set source signal.
GevTimestampValueAtSet Controls the value to be set in the counter when the set event occurs.
GevTimestampResetSource Selects the signal that resets the counter (to 0).
GevTimestampResetActivation Selects the activation mode for the counter reset source signal.
GevTimestampTickFrequency Indicates the number of timestamp ticks in 1 second (frequency in Hz).
GevTimestampControlLatch Latches the current timestamp counter into GevTimestampValue.
GevTimestampControlSet Sets the counter to GevTimestampValueAtSet.
GevTimestampControlReset Rests the timestamp counter to 0.
GevTimestampValue Returns the latched 64-bits value of the timestamp counter.
GevCCP Controls the device access privilege of an application.
GevMCPHostPort Controls the port to which the device must send message.
GevMCDA Controls the destination IP address for the message channel.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
48/53
Page 49
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Name Description
GevMCTT Provides the transmission timeout value in miliseconds.
GevMCRC Controls the number of retransmissions allowed when a message channel message
time out.
GevMCSP This feature indicates the source port for the message channel.
GevStreamChanelSelector Selects the stream channel to control.
GevSCPDirection Reports the direction of the stream channel.
GevSCPInterfaceIndex Index of network interface to use.
GevSCPHostPort Controls the port of the selected channel to which a GVSP transmitter must send data
stream or the port from which a GVSP receiver may receive data stream.
GevSCPFireTestPacket Sends a test packet.
GevSCPSDoNotFragment The state of this feature is copied into the “do not fragment” bit of IP header of each
stream packet.
GevSCPSBigEndian Endianess of multi-bytes pixel data for this stream.
GevSCPSPacketSize Specifies the stream packet size, in bytes, to send on the selected channel for a GVSP
transmitter or specifies the maximum packet size supported by a GVSP receiver.
GevSCPD Controls the delay (in timestamp counter unit) to insert between each packet for this
stream channel.
GevSCDA Controls the destination IP address of the selected stream channel to which a GVSP
transmitter must send data stream or this destination IP address from which a GVSP
receiver may receive data stream.
GevSCSP Indicates the source port of the stream channel.
UserSetControl
Name Description
UserSetSelector Selects the feature User Set to load, save or configure.
UserSetLoad Loads the User Set specified by UserSetSelector to the device and makes it active.
UserSetSave
UserSetDefaultSelector
Save the User Set specified by UserSetSelector to the non-volatile memory of the
device.
Selects the feature User Set to load and make active by default when the device is
reset.
IPEngine
Name Description
ProgrammableLogicController Category that contains the Programmable Logic Controller (PLC) features.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
49/53
Page 50
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
SpecialFeatures
Name Description
ReloadGammaData Gamma table reload from EEPROM to RAM.
GammaMode Gamma mode selection.
Min_ShutterTime Minimum shutter speed for Auto shutter control mode. Unit: us.
Max_ShutterTime Maximum shutter speed for Auto shutter control mode. Unit: us
AGCRange Maximum gain value for AGC.
TargetBrightness Target brightness for ALC.
ALC_Peak_Average Ratio of peak and average fro ALC.
DigitalGain Digital gain
ALCWeight1 Weight of the area determined by ALCWindowV1, ALCWindowV2, ALCWindowH1 and
ALCWindowH2 for ALC.
ALCWeight2 Weight of the area determined by ALCWindowV1, ALCWindowV2, ALCWindowH2 and
ALCWindowH3 for ALC.
ALCWeight3 Weight of the area determined by ALCWindowV1, ALCWindowV2, ALCWindowH3 and
ALCWindowH4 for ALC.
ALCWeight4 Weight of the area determined by ALCWindowV2, ALCWindowV3, ALCWindowH1 and
ALCWindowH2 for ALC.
ALCWeight5 Weight of the area determined by ALCWindowV2, ALCWindowV3, ALCWindowH2 and
ALCWindowH3 for ALC.
ALCWeight6 Weight of the area determined by ALCWindowV2, ALCWindowV3, ALCWindowH3 and
ALCWindowH4 for ALC.
ALCWeight7 Weight of the area determined by ALCWindowV3, ALCWindowV4, ALCWindowH1 and
ALCWindowH2 for ALC.
ALCWeight8 Weight of the area determined by ALCWindowV3, ALCWindowV4, ALCWindowH2 and
ALCWindowH3 for ALC.
ALCWeight9 Weight of the area determined by ALCWindowV3, ALCWindowV4, ALCWindowH3 and
ALCWindowH4 for ALC.
ALCWindowV1 1st vertical line (1st from the top) position for the area for ALC.
ALCWindowV2 2nd vertical line (2nd from the top) position for the area for ALC.
ALCWindowV3 3rd vertical line (3rd from the top) position for the area for ALC.
ALCWindowV4 4th vertical line (4th from the top) position for the area for ALC.
ALCWindowH1 1st horizontal (1st from the left) position for the area for ALC.
ALCWindowH2 2nd horizontal (2nd from the left) position for the area for ALC.
ALCWindowH3 3rd horizontal (3rd from the left) position for the area for ALC.
ALCWindowH4 4th horizontal (4th from the left) position for the area for ALC.
WB_WindowH1 Horizontal start position of the area for auto white balance (Horizontal start position from
left)
WB_WindowH2 Horizontal end position of the area for auto white balance (Horizontal end position from
left)
WB_WindowV1 Vertical start position of the area for auto white balance (Vertical start position from left)
WB_WindowV2 Vertical end position of the area for auto white balance (Vertical end position from left)
WB_WindowMode Select white balance window mode.
YThreshold The value for auto white balance is determined with the color information of the pixels,
which is more than this threshold.
ModeCode Mode code.
HardwareVersion Hardware version.
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
50/53
Page 51
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
Name Description
FPGAFirmwareVersion FPGA Firmware Version.
FirmwareVersion Firmware Version.
SerialNumber Serial number.
CustomerCode Customer code.
No.14S002-08
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
51/53
Page 52
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
10 Revision History
Rev
00 2014/06/30 New Document
01 2014/07/03 Revised
02 2014/07/11 Revised
03 2014/07/29 Revised
04 2016/03/14 Revised
05 2017/04/17 Revised
06 2017/07/03 Revised
07 2018/09/03 Revised
08 2019/02/27 Revised
GigE Vision is trademark of AIA.
GenICam is trademark of EMVA.
Other company names and product names in this document are trademarks of their respective owners.
Date Changes Note
Added Explanation of RGB output setting
Added Minimum Scene Illumination
Aluminum (AC) to Aluminum Alloy, Power Cumsumption
Camera Mount Screws
Address, TEL, FAX number for relocation
Change the name of company
Change the electronic specifications list (Image output format)
Change sensor information (Bayer)
Added trademark information
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
52/53
Page 53
No.14S002-08
Aegis Electronic Group, Inc.
For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *aegis-g2@aegiselect.com *http://www.aegiselect.com
(888)687-6877
STC-SBE132POE / STC-SCE132POE
Product Specifications and User’s Guide
53/53
Loading...