Omega Executive model One 1.2 User's Manual

Table Of Contents

Model ONE

OWNER'S GUIDE

ClassicOne & UltraOne

Version 1.2

Keyless Entry and Security

ULTIMATE FLEXIBILITY

IN VEHICLE SECURITY

Welcome to the convenience and security of your Model One system. Model One is designed and manufactured by Omega Research and Development, a world leader in vehicle convenience and security since 1975. Your system offers easy, carefree operation, and the modular design allows its many impressive features to be customized to suit your needs

Therefore, please note that this guide is written to reflect:

- that a power doorlock interface is installed with your system. This interface may

vary from one vehicle to the other, and in some cases may involve optional

components.

- that the vehicle's horn is used for the audible output; an optional electronic siren

is also available and is used with the UltraOne system.

- the Programmable Features in the default settings; the operations of these

features, if selected otherwise, are also explained in detail. The addition of an optional sensor is also affects the exact operations, as several types of auxiliary threat-detection sensing devices are available.

This sophisticated, state-of-the-art product deters theft of your vehicle, and its contents. Model One systems are designed for professional installation, and are available through new car retail outlets only.

Introduction

Page - 3

Introduction Remote Transmitter Operations ( Arming and Disarming the System

Active Arming & Sensor By-Pass .............................................................................

Passive Arming ........................................................................................................

Disaming ..................................................................................................................

The Armed System ....................................................................................9-11

The Valet Switch - Valet Mode and Override

Easy ValetTM.........................................................................................................

Selectable Code Override ..................................................................................

Remote Panic ..........................................................................................14-15

The LED Status Light

Audible and Visual Indicators ...................................................................17-18

Option Output and Additional Output .............................................................19

Shock Sensor Port with Prewarn...................................................................22

Programming Transmitters .......................................................................22-25

Programming Features.............................................................................25-28

Programmable Features ...........................................................................29-39

Limited Lifetime Warranty ...............................................................Back Cover

Your Model One system has three principal user components: the Remote

Transmitter, the red LED Status Light and the Valet Switch.

The Remote Transmitter: Each system is capable of being operated by up to four different remote transmitters. The remote transmitter has four push-button switches, each being labeled as to function. These are:

- The LOCK button arms the security system, which also locks the doors. This

button can also operate an additional "option" output.

- The UNLOCK button disarms the security system, unlocking the doors. This

operation can be configured to unlock the driver's door only upon one press of the

button; then, if desired, all of the doors upon a second press of the button.

- The OPTION button is used to silently arm or disarm the system, and can also

operate an additional remote control function such as trunk release.

- The PANIC button is used to easily engage and disengage the panic feature.

The Red LED Status Light: Informs you at a glance of the different conditions the security system is in and also serves as a visual deterrent to break-ins and theft.

The Valet Switch: Is used to access Valet Mode, which allows the operator to suspend some of the security system's normal functions. The valet switch may also be used, instead of the remote transmitter, to override an armed and activated system.

Remote Transmitter, LED Status Light & Valet Switch

Operations At A Glance

System Status, ATVTM & Zone Violation ......................

Page - 2

Page - 4

) ................................ 5

) .....................3-4

6-7 7-8 8-9

11-12 12-14

15-17

Remote Transmitter Operations

Arming and Disarming the System

Pressing and releasing the LOCK button arms the security system and locks the doors. Pressing and holding this button for two seconds will, in addition to the arming and locking, also activate the optional additional output.

LOCK

OPTION

Pressing and releasing the UNLOCK button disarms the system and unlocks

the doors unless the system is activated. The unlock operation may be

LOCK

PANIC

configured so that pressing the unlock button once disarms the system and unlocks only the driver's door, and pressing a second time will unlock all

Pressing and releasing the

of the doors.

OPTION button twice arms or disarms the system without the confirmation horn chirps. Pressing this button for two seconds can be used to activate an optional function such as trunk release.

Transmitter part number: #104-07

for 2 seconds will activate the system, flashing the lights and sounding the horn; a further press of this button will deactivate the system, into the disarmed state. If desired, this button can be programmed to operate the additional optional output instead of the panic feature.

Pressing the PANIC button

Page - 5

system from the transmitter, but with the indication that a protected circuit is not secure. After arming, the bypassed circuit will automatically be reinstated for protection should it become operative, i.e., if the trunk is closed, 3 seconds later protection of this circuit is restored. When a circuit is in a bypassed state, all other operating circuits will be protected normally. If desired, this feature may be custom programmed to also operate if a door is open upon when arming the system with the transmitter.

Passive Arming: The Model One can be custom programmed to arm itself automatically when the vehicle's last door is closed; this is the Last Door Arming feature. If this feature is programmed to operate, the moment the last open door is closed the horn chirps once and the parking lights flash once to confirm that all points of entry are closed, and that the arming sequence has begun. The arming period lasts 30 seconds, and is indicated by a fast-flashing LED status light. Thirty seconds after the last door was closed, the horn will chirp again, the parking lights will flash once, confirming completion of the Last Door Arming sequence. Three seconds later, the LED status light changes to flashing slowly, and the system is fully armed. If a point of entry is reopened before the single chirp and parking light flash occurs at 30 seconds, the Last Door Arming sequence stops, but will start over again when the opened point of entry is closed again. To temporarily prevent the system from Last Door Arming (example: while vehicle is being refueled), you should put the system into Valet Mode or leave the vehicle's door open (in most cases, turning on

"Arming" the Model One locks the doors places the security system into a state in which the vehicle is monitored for intrusion attempts. There are two different methods of arming the system: "active" arming by use of the remote transmitter, and automatic, or "passive" arming, which is programmable.

Active Arming: The Model One can always be armed with the remote transmitter, provided the ignition switch is "off" and the system is not in Valet Mode. Simply press the transmitter LOCK button once. The doors will lock, the parking lights will flash once, the vehicle's horn will chirp once, the LED Status Light will begin flashing, and the starter interrupt circuit engages to prevent any attempt to start the vehicle. When arming the UltraOne system, the dome light also flashes once. Three seconds after the horn chirp the system becomes fully armed, as indicated by the LED status light changing from a rapid flashing to a slow flashing. Once armed, the system will activate if an intrusion attempt is detected. If desired, the system may be armed without the normal confirmation horn chirp by pressing and releasing the transmitter's OPTION button twice within 3 seconds.

Upon active arming, if any protected circuit except for the doors is inoperable, the horn will chirp three times and the parking lights will flash three times. This is Arming Bypass, and when it occurs, protection for the affected circuit will be temporarily bypassed. For example, if the trunk is left open, you can still actively arm the

Page - 6

the dome light will suffice). The "Last Door Arming" feature offers a high level of security, since you do not have to remember to arm the system each time you exit from your vehicle, and may qualify you for an insurance discount.

A separate programmable feature may be utilized to have the doors automatically lock when the 30 second horn chirp and light flash occurs. The previously mentioned Arming Bypass feature cannot operate with Last Door Arming; it only works when actively arming the system from the transmitter because all protected entries must be closed to initiate Last Door Arming. Of course, you can still arm the system instantly from the remote transmitter at any time during the 30 second Last Door Arming sequence.

Disarming: Press and release the remote transmitter's UNLOCK button once to disarm the system and unlock either the driver's door only, or all of the doors. How the doors unlock is determined by the installation configuration of the doorlock interface. Disarming is confirmed by the horn chirping twice and the parking lights turning on for 30 seconds to illuminate the way to your vehicle; the UltraOne will also illuminate the interior lights. During this 30 second period of illumination, if the ignition switch is turned "on" the lights will immediately turn off.

If the transmitter is not available or inoperative, the system must be disarmed by use of the Selectable Code Override, which is explained in detail on pages 12-14.

Page - 7

Page - 8

However, if the security system was activated while you are away, the disarm confirmation will be 4 horn chirps, and the lights will flash 4 times before staying on for 30 seconds. The system will have this disarming response until the ignition switch is turned "on". Also, anytime the security system has been activated, upon disarming the LED status light will indicate which of the protected zones caused the activation by flashing a code of numbered flashes between pauses. Again, this indication remains until the ignition switch is turned "on".

The system may be disarmed without the normal confirmation chirps by pressing

and releasing the transmitter's OPTION button twice within 2 seconds.

The Armed System

When the Model One is armed, the LED status light flashes continuously in a slow and steady manner. In this state, any violation of a protected entry or optional sensor will instantly activate, or "trigger" the system. If the system is activated:

- The vehicle's horn or the optional electronic siren will sound. The horn will

repeatedly sound for one second, then pause for one second. Every ten

seconds, the horn will stop sounding completely for 5 seconds; this prevents

the horn from overheating. This audible output will occur for the duration of the

activated cycle. The optional siren, used with the UltraOne, features six different

tones, and every 5 seconds the siren will change the tone to generate more

attention to the vehicle.

- The parking lights will flash on and off repeatedly.

Page - 9

- The doors will relock. If opened, relocking will occur when the door is closed. The horn will sound and lights will flash for 60 seconds, unless you disarm the

system with the transmitter by pressing the UNLOCK button. If needed, the valet switch and ignition key may be used to disarm the system (Selectable Coded Override; pages 12-14). Please note that while the system is activated, pressing the UNLOCK button will only disarm the system, and not unlock the doors; simply press UNLOCK again to unlock the doors.

If all protected entries are secure at the end of 60 seconds, the system will stop

itself and rearm automatically to detect another entry attempt. If there is a protected entry still open, or a sensor still in a violated state at the end of 60 seconds, the system will reactivate for two more 60 second cycles. If this occurs, the system will still stop itself after a total of 3 minutes and rearm automatically, and ignore the open entry or violated sensor circuit while protecting the other circuits. Should the entry be closed or the sensor return to normal, protection will be reinstated for the affected circuit.

After the security system is activated, the confirmation upon disarming will no

longer be the normal two horn chirps, and the lights staying on for 30 seconds. Instead, the system will have 4 horn chirps and the lights will flash 4 times before staying on for 30 seconds. Additionally, the LED Status Light will change to flashing two to five times between pauses, indicating which protected zone activated the system. The LED Status Light will continue flashing this Violation Code until the ignition key is turned “on”.

Page - 10

The Valet Switch - Valet Mode and Override

The valet switch, which is typically contained within the same housing as the LED status light, allows the operator to suspend certain functions of the Model One's normal operations. It is also used in an emergency override disarming of an armed and activated system, should the transmitter be unavailable or inoperative.

These are two separate and distinct operations: the first is Easy ValetTM, whereby a

disarmed

without use of the ignition key; the second operation is Selectable Code Override, which will disarm an key. The valet switch is also used in transmitter and features programming operations, which are described in later sections of this guide.

Easy Valet

is in the disarmed state. Easy ValetTM is unique because other security systems require the ignition switch to be "on" to enter Valet Mode, but with the Model One, the ignition can be either "on" or "off", so the ignition key is not required.

Whenever the security system is disarmed, simply press and hold the valet switch for two seconds to enter the Valet Mode. The system will confirm it is entered Valet Mode with two horn chirps and the LED status light will illuminate and stay on constantly. The system will remain in Valet Mode if the ignition is turned "on" or "off", or even if the system is disconnected from the vehicle's electrical system. This is useful for servicing the vehicle; unless in a Valet Mode, the security system will

system may be placed into an "off" or "standby" condition (Valet Mode)

armed or activated

: This unique feature can be utilized anytime the security system

system and requires the use of the ignition

Page - 11

activate immediately when power and ground are first applied, such as when reconnecting a battery.

While in the Valet Mode, the remote transmitters can still operate the panic feature, the power door locks, or the trunk release, if equipped. Valet Mode prevents the system's alarm from being armed; using the transmitter to lock the doors still engages the starter interrupt, resulting in the LED status light flashing in a normal manner as an indication of this. To subsequently start the vehicle, either the transmitter must be used to unlock the doors, or valet switch must be used to disengage the starter interrupt. Additionally, the doors will lock when the ignition is turned "on" and unlock when it is turned "off"', if the system is programmed to do so. To remove the system from the Valet Mode, simply momentarily press the valet switch. The system will instantly revert to the disarmed condition. To confirm that the system has exited the Valet Mode, the LED status light will be extinguished. Remember, Easy ValetTM only operates when the system is in a disarmed state - an armed state, or if the doors are locked from using the transmitter, requires using the Selectable Code Override.

How to Disarm the System Without Using the Transmitter

Selectable Code Override: In the event the transmitter is lost, damaged, or it

is otherwise inoperable, the valet switch and your ignition key may be used to disarm the system. Selectable Code Override offers a high level of security because, in

Page - 12

+ 7 hidden pages