Page 1
Limited Lifetime Warranty
Products manufactured and sold by Omega Research & Development, Inc. (the Company), are
warranted to be free from defects in materials and workmanship under normal use. If a product sold
by the Company proves to be defective, the Company will repair or replace it free of charge within
the first year and thereafter all parts to be repaired will be free with only a nominal charge for Omega's
labor and return shipping, during the lifetime of the car in which it was originally installed.
All products for warranty repair must be sent postage prepaid to Omega Research &
Development, Inc., P.O. Box 508, Douglasville, Georgia 30133, with bill of sale or other dated proof
of purchase. This warranty is nontransferable and does not apply to any product damaged by
accident, physical or electrical misuse or abuse, improper installation, alteration, any use contrary
to its intended function, unauthorized service, fire, flood, lightning, or other acts of God.
This warranty limits the Company's liability to the repair or replacement of the product. The
Company shall not be responsible for removal and/or reinstallation charges, damage to or theft of
the vehicle or its contents, or any incidental or consequential damages caused by any failure or
alleged failure of the product to function properly. Under No Circumstances Should This Warranty,
Or The Product Covered By It, Be Construed As A Guarantee Or Insurance Policy Against Loss. The
Company neither assumes nor authorizes any person or organization to make any Warranties or
assume any liability in connection with the sale, installation, or use of this product.
This device complies with FCC Rules part 15. Operation is subject to the following
two conditions, (1) This device may not cause harmful interference and, (2) This
device must accept any interference that may be received, including interference that
may cause undesired operation.
MO_E2300ATV
"Convenience And Security For A Mobile Society"
OWNER'S MANUAL
For model:
Executive 2300
Please note that your new Executive Keyless Entry and Security system has
Programmable Features which allow the customizing of its operations.
The Programmable Features may affect the exact operations as described
in this guide, which reflects a typically-installed system with factory-set
conditions of the Programmable Features. Please consult the installing
dealer for information regarding the custom-programming of these features, which may affect the operations of your Executive system.
COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT 1997
ATV
Table Of Contents
Introduction .....................................................................................................3
TM
Automatic Transmitter Verification
Transmitter Featuress ...................................................................................... 4
Transmitter Functions ......................................................................................5
LED Status Light .............................................................................................6
TM
Easy Valet
Switch .................................................................................... 7-8
Starter Disable .................................................................................................8
Audible Confirmation......................................................................................9
Programming Transmitters............................................................................10
User Programmable Features .................................................................. 11-12
Changing The User Programmable Features........................................... 12-14
Glossary ................................................................................................... 14-15
Tips To Avoid Becoming A Victim ..............................................................15
Limited Lifetime Warranty ............................................................Back Cover
......................................................... 3-4
Page - 2
Introduction
Congratulations on your purchase of an Executive Keyless Entry and Security system.
You have purchased the E-2300
Executive series of personal convenience and security products are designed by Omega Research and
Development, a leader in vehicle security since 1970. When beginning to use this system, you will be
surprised at its user-friendly design, considering the system delivers features and benefits that not only
anticipate, but exceed, your expectations.
To learn how to operate your system, this Owner's Operation Manual will begin with Transmitter
Functions, then explain the system's other operations as enhanced by the factory-set Programmable
Features. As you become more familiar with the basic operations that this model performs, this Manual
will further discuss the User Programmable Features, and then explain how change to them to configure
the system to suit your personal needs. Finally, this Manual has personal safety tips, and will also briefly
explain common technical terms.
Automatic Transmitter Verification
You received two remote control transmitters to operate your Executive System. Each time the
ignition switch is turned to the "run" position the Red LED Status Light located on or under the
dashboard will indicate for 10 seconds the number of transmitters programmed to your system. For
example: Two flashes and a pause indicates two transmitters are coded to operate the system.
ATV
, a Remote Keyless Entry System with Starter Disable. The
TM
Page - 3
Continued Next Page
Page 2
IMPORTANT: For the first 48 hours after a transmitter is coded to operate the system, every
time the ignition switch is turned "on", the built-in piezo buzzer will beep rapidly for two seconds,
and the LED Status Light will flash for 90 seconds. If this occurs after the initial 48 hour period,
immediately reprogram your transmitters (See Page 10).
This Patented feature alerts you if someone has added an unauthorized transmitter to your system, and
is found only in Omega Research and Development products.
Transmitter Features
Concealed Transmitter Codes: Each Executive system includes two transmitters, and up to two
additional transmitters can be stored in the unit's memory for your convenience. Each transmitter has
its own unique code. Thus, no other transmitter is coded the same as yours. In fact, no one, including
the factory, can program another transmitter exactly like yours because the code is built inside the
transmitter's microprocessor and cannot be seen or copied.
Transmitter Code Jumping
to the next digital code in sequence. Each time the system receives the correct digitally encoded signal
from your transmitter, the receiver will then advance to the next digital code in sequence to match the
transmitter. Therefore, you can never transmit the same code twice, thereby preventing a code grabbing
device from operating your system.
Transmitter Battery Saver Feature: Many times transmitter batteries are prematurely exhausted
because the transmitter buttons are inadvertently pressed by objects while in a pocket or purse. The
Executive transmitter will turn itself "off" after a short period of continuous transmission, and thus
prevent drained transmitter batteries.
TM
: Each time you press a transmitter button its signal will advance
Page - 4
Transmitter Functions
LOCK BUTTON
Pressing the transmitter
Lock button will lock
all of the doors.
LOCK
Your Executive system will
lock your doors upon turning the
ignition "On", and unlock them
when the ignition is turned "Off".
Instructions for programming up to 4 transmitters
to your Executive system are found on Page 10.
All Executive Keyless Entry and Security Systems can use the same Remote Transmitters. Your
system is capable of being operated by up to four
Executive transmitters, which are available from the
dealership where you purchased your system.
OPTION
Executive
Keyless Entry &
Security
Page - 5
GREEN LED LIGHT
Illuminates whenever any
transmitter button is pressed.
UNLOCK BUTTON
Pressing the transmitter
UN
LOCK
Unlock button will
unlock all of the doors.
On certain vehicles, pressing
the unlock button once unlocks
only the driver's door. Pressing
a second time will unlock all of
the doors.
OPTION BUTTON
Pressing the Option button for two seconds
can be used to activate remote trunk release
(vehicles equipped with power trunk
release) or other optional equipment, such
as Remote Car Starters.
L E D Status Light
The E-2300
condition. Your system features a Starter Disable circuit, the status of which is also reflected by the
Red LED Status Light. These are the conditions of the LED Status Light:
LED Off......................................................................Ignition switch is "On". Also, the system
is "at rest", indicating that no automatic
features (which may have been programmed
to operate) will occur.
LED On Solid Red .....................................................System is in "Valet Mode".
LED Flashing Rapidly................................................ Starter Disable has been programmed to
automatically engage.
LED Flashing Slowly .................................................Starter Disable is engaged. This will occur
LED Flashes 1 To 4 Times After Ignition "On" ........ Number of transmitters stored in the system.
These four indicators are part of the Auto matic Transmitter Verification
* LED is the abbreviation for Light Emitting Diode - which is defined in the Glossary.
ATV
includes a Red LED Status Light* to inform you of the system's operational
whenever the transmitter is used to lock the
doors. The Starter Disable may also be
programmed to operate automatically.
TM
feature.
Page - 6
TM
Easy Valet
The Easy Valet
interrupt any optional automatic functions, such as Starter Disable, which may be programmed to
operate. The Easy Valet
TM
Switch is used to place the system into Valet Mode, which is used to stop or
TM
Switch, in conjunction with your ignition key, also allows you to override
Switch
the system in the event of a lost or damaged transmitter, leaving the vehicle for servicing, washing, or
valet parking.
Easy Valet
TM
Mode: This feature allows you to activate the Valet Mode at any time by pressing
the Easy Valet Switch button for 2 seconds, unless the Starter Disable is engaged (this is indicated by
a slow flashing Red LED Status Light). Please note that once the Starter Disable is engaged, the ignition
switch must be turned "on" to enter the Valet Mode. When utilizing the Easy Valet
pressing the Easy Valet
TM
Switch, the Red LED Status Light will illuminate a steady, solid Red, and
TM
Mode, upon
the built-in piezo buzzer will beep once. While the system is in the Valet Mode, the Red LED Status
Light will remain solid Red (not flashing) at all times, and every time the ignition switch is turned "off",
the built-in buzzer will beep once as a reminder of this condition. To remove the system from Valet
Mode simply press the Easy Valet
TM
Switch at any time. The transmitter will operate normally while
the system is in Valet Mode, i.e., the doors will lock and unlock, the Option Button will still operate
- but the Starter Disable will not operate, and any programmed automatic functions are suspended.
Overriding The System: As mentioned in the previous section, once the Starter Disable is
engaged, the ignition key is required to allow the Easy Valet
TM
Switch to override the system and allow
starting the engine. To obtain a System Override, follow this procedure:
Page - 7
Continued Next Page
Page 3
Step 1. Enter the vehicle normally.
Step 2. Using your key, turn "on" the ignition. Be prepared to perform the
following Step before 5 seconds expires.
Step 3. Within 5 seconds, press and release the Easy ValetTM Switch. The system
will be immediately overridden.
Audible Confirmation
The E-2300
command is received. This confirmation is designed to be heard only while inside the vehicle.
ATV
includes a built-in piezo buzzer for audible confirmation when a transmitter
Once the activated system has been overridden, if Valet Mode is desired, holding the Easy Valet
Switch depressed for two seconds will place the system into Valet Mode.
Starter Disable
The E-2300
to lock the doors), and may be configured, if desired, to also provide an automatic (passive) Starter
Disable. The optional passive Starter Disable may qualify you for an insurance discount, so please
check with your insurance agent.
Active Starter Disable: Whenever the doors are locked via the transmitter, the Starter Disable will
instantly engage. Unlocking the doors with the transmitter will deactivate the Starter Disable circuit,
allowing the engine to be started. Please note that the Starter Disable may be configured to
automatically reengage 90 seconds after the doors are unlocked by the transmitter; or, to engage
automatically 90 seconds after the ignition switch is turned "off". These automatic Starter Disable
options are explained in more detail in the "User Programmable Features" section of this Owner's
Manual.
ATV
provides an active Starter Disable (which engages every time the transmitter is used
Page - 8
Programming Transmitters
Programming Transmitters To Operate Your Executive System: To use an additional or
replacement transmitter, it's unique digital code must first be added to the Executive System module's
memory. The dealership where you purchased your Executive System can provide and program
transmitters for you, or you may program the transmitters yourself. If you wish to program a
transmitter, please follow these Transmitter Programming Mode procedures carefully:
TM
Standard Confirmation Operations
One Beep ....................................................................The transmitter has locked the doors and/or
the Starter Disable has engaged.
Two Beeps ..................................................................The transmitter has unlocked the doors and
the Starter Disable is disengaged.
Two Beeps ..................................................................The system has just been placed into Valet
(With LED Illuminated Steady) Mode.
Two Beeps When The
Ignition Switch Is Turned "Off" .................................The system is reminding you that it is in
Valet Mode.
Special Confirmation Operations
Beeps For Two Seconds
When The Ignition Switch Is Turned "On"................The Automatic Transmitter Verification
feature system is alerting you that transmitter
programming activity has occurred within the
last 48 hours.
Page - 9
User Programmable Features
Your E-2300
requirements as part on the Transmitter Programming Mode. Once Transmitter Programming Mode
has been accessed (described on the previous page), at the point where the first transmitter code is
entered and acknowledged, that same transmitter may be used to configure these User Programmable
Features as desired. The User Programmable Features, and their factory default settings, are:
ATV
has four User Programmable Features which may be easily configured to your
1) Have all the transmitters that you wish to operate your Executive System at hand. Any time
a transmitter code is programmed into your Executive System, all existing codes are
automatically erased. This, in addition to the Automatic Transmitter Verification
prevents someone from adding an unauthorized transmitter to your system.
2) Within a 5 second period, turn the ignition switch "on" five times: "on", "off", "on", "off", "on",
"off", "on", "off", then "on" again; the fifth time leaving it "on". The buzzer will sound briefly
to indicate that the system is ready to receive transmitter codes.
3) Within 10 seconds press the LOCK button on the first transmitter you wish to encode to the
system. The buzzer will beep once to indicate the transmitter's code is learned by the system.
It is only necessary to press the LOCK button, as the rest of the transmitter's functions are
assigned automatically.
4) Repeat Step 3 within 10 seconds for each additional transmitter. The system will leave
Transmitter Programming Mode when the ignition switch is turned "off", after 10 seconds of
not receiving a transmitter broadcast, or upon learning the fourth transmitter.
TM
feature,
Page - 10
1) The Doors Automatically Lock 90 Seconds After The Ignition Switch Is Turned "Off".
Default: Feature OFF; Program with the transmitter's LOCK button.
When this Feature is activated (turned ON), every time the ignition switch is turned "Off", the
doors will automatically lock 90 seconds later. You may open a door and exit the vehicle
without affecting this operation, and the LED Status Light will have no indication that the
automatic locking will occur.
2) The Doors Automatically Relock 90 Seconds After Unlocking By The Transmitter.
Default: Feature OFF; Program with the transmitter's UNLOCK button.
When this Feature is activated (turned ON), every time the transmitter is used to unlock the
doors", they will automatically relock 90 seconds later. Opening a door will not affect this
operation, although turning "On" the ignition switch will cancel the automatic relocking. The
LED Status Light will have no indication that the automatic relocking will occur.
3) The Starter Disable Will Automatically Engage 90 Seconds After The Ignition Switch Is
Turned "Off"
Default: Feature OFF; Program with the transmitter's OPTION button.
And 90 Seconds After Unlocking By The Transmitter.
Page - 11
Continued Next Page
Page 4
When this Feature is activated, the Starter Disable circuit will automatically engage 90
seconds after the ignition switch is turned "Off" and also 90 seconds after the transmitter is
used to unlock the doors. The later may be cancelled by turning the ignition switch "On", but
upon turning the switch "Off" the former parameter of the Feature will cause the Starter
Disable to engage 90 seconds later. Please note that when this form of automatic Starter
Disable is selected, there is no indication of the impending engagement; once the Starter
Disable is engaged, however, the LED Status Light will flash as an confirmation indicator.
4) The Starter Disable Will Automatically Engage 90 Seconds After Unlocking By The Transmitter.
Default: Feature OFF; Program with the transmitter's LOCK
When this Feature is activated, the Starter Disable circuit will automatically engage 90
seconds after unlocking the doors by use of the transmitter. The ignition switch must be turned
"On" to cancel the automatic engagement. Please note that when this form of automatic Starter
Disable is selected, there is no indication of the impending engagement; once the Starter
Disable is engaged, however, the LED Status Light will flash as an confirmation indicator.
and UNLOCK button in unison.
Changing The User Programmable Features
As previously mentioned, changing the User Programmable Features is a variation of the procedure
used to program transmitter codes to the system. Remember, when the system acknowledges the first
transmitter code, at that point you may use that transmitter to change any or all of the five User
Programmable Features. To change the User Programmable Features, follow this procedure:
Page - 12
Every time the appropriate button or button combination is pressed, the system will respond
alternately with one beep, then two beeps - every time the button is pressed, the Feature
assigned to it is "toggled" on or off. One beep indicates that the Feature is on, or activated;
two beeps indicates that the Feature is off, or deactivated.
1) Have all the transmitters that you wish to operate your Executive System at hand. Even though
you are reprogramming an existing code, any time a transmitter code is programmed into your
Executive System, all existing codes are automatically erased.
2) Within a 5 second period, turn the ignition switch "on" five times: "on", "off", "on", "off", "on",
"off", "on", "off", then "on" again; the fifth time leaving it "on". The built-in piezo buzzer will
sound briefly to indicate that the system is ready to receive transmitter codes.
3) Within 10 seconds press the LOCK button on the first transmitter you wish to encode to the
system. The buzzer will beep once to indicate the transmitter's code is learned by the system.
At this point, you may use this transmitter to change the User Programmable Features.
4) Within 10 seconds, press the transmitter button or button combinations to change the desired
Feature. Here is a condensed review of the four Features and the transmitter button(s) to use
when programming:
The Doors Automatically Lock 90 Seconds After The Ignition Switch Is Turned "Off".
Program with the transmitter's LOCK button.
The Doors Automatically Relock 90 Seconds After Unlocking By The Transmitter.
Program with the transmitter's UNLOCK button.
The Starter Disable Will Automatically Engage 90 Seconds After The Ignition Switch
Is Turned "Off"
Program with the transmitter's OPTION button.
The Starter Disable Will Automatically Engage 90 Seconds After Unlocking By The
Transmitter.
Program with the transmitter's LOCK
(RF) signal whenever any of its buttons is pressed. Since the transmitter is limited to a single frequency
assigned by the Federal Communications Commission (FCC), it's signal must be encoded so that only
your transmitter will operate your vehicle. See "Code" above.
Valet Mode - A condition in which the starter disable will not engage.
And 90 Seconds After Unlocking By The Transmitter.
and UNLOCK button in unison.
Page - 13
Continued Next Page
5) When all of the desired Features have programmed as desired, repeat Step 3 within 10 seconds
for each additional transmitter. Remember, 10 seconds of not receiving a transmitter broadcast
will cause the system will leave either the Transmitter Programming Mode or the User
Features Programming period.
Glossary
Code - A digital signal which is assigned to each transmitter to make it unique and different from other
transmitters. This is done in all Executive transmitters at the factory and cannot be duplicated.
Code Grabbing - A method whereby a thief, using a device that records and then plays back a copy
of your transmitter's signal, gains entry to your vehicle.
Code Jumping
Grabber units ineffective.
Keyless Entry - A popular option that allows you to lock and unlock your vehicle's doors by means
of a transmitter or key pad, without the use of the normal car key.
LED - Commonly used term for Light Emitting Diode, an electrical component that, in addition to
illuminating when electricity flows through it, limits the flow of electricity to one direction only. For
practical purposes, consider it as an indicator light.
Starter Disable - A device, when engaged, that will prevent starting the vehicle's engine.
Transmitter - The small remote control attached to your key ring that will emit a Radio Frequency
TM
- The transmitter's ability to change it's code each time it transmits, rendering Code
Page - 14
Tips To Help Avoid Becoming A Victim
1) Always be aware of your surroundings. An alert and aware person is less likely to become a
crime victim than someone who is preoccupied and easily approached.
2) While driving in high crime areas, always keep your doors locked and your windows up. Your
Executive System can automatically lock your doors when the ignition switch is turned "on".
3) Always attempt to park your vehicle in a well lit and visible location with your doors locked.
4) While in parking garage structures, always attempt to back in to your parking space. This will
provide a less visually encumbered and quicker way to exit your parking space if you are being
pursued.
5) While driving or stopped at an intersection, if your vehicle is bumped in the rear by another vehicle
or the vehicle behind you is flashing it's headlights, consider the occupants of the vehicle hostile
and immediately drive to the nearest police or fire station. "Bump and run" thieves and carjackers are becoming an increasingly severe problem.
6) Control access of your keys. Never leave your house and other keys with a valet parking attendant
mechanic, or any person requiring access to your car keys.
7) Control access of your keys. Never leave your house and other keys with a valet parking attendant
mechanic, or any person requiring access to your car keys.
8) After someone else has had access to your vehicle, always verify that your transmitters still
operate your system, and be aware of the Automatic Transmitter Verification
Page - 15
TM
feature.
Loading...