Olympus SZ2-ILST Instructions Manual

INSTRUCTIONS

SZ2-ILST

LED ILLUMINATOR STAND

This instruction manual is for the Olympus SZ2-ILST LED Illuminator Stand. To ensure the safety,
obtain optimum performance and to familiarize yourself fully with the use of this equipment,
we recommend that you study this manual thoroughly before operating the system.
Retain this instruction manual in an easily accessible place near the work desk for future reference.

A X 6 6 1 3

For Korea only

B급 기기 (가정용 방송통신기자재)

이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을

목적으로 하며, 모든 지역에서 사용할 수 있습니다.

CONTENTS

SZ2-ILST

IMPORTANT — Be sure to read this chapter for safe use of the equipment. —

1 NOMENCLATURE

2 ASSEMBLY

3 OPERATION

1 Lighting the Illuminator and Adjusting the Light Intensity ....................................................... 5

2 Adjusting the Reflected (Oblique) Illumination Angle .................................................................... 5

Adjusting the Focus Adjustment Knob Tension ..................................................................................... 5

3

4 SPECIFICATIONS

PROPER SELECTION OF THE POWER SUPPLY CORD ............................................................................

1-2

3

4

5

6

7-8

In accordance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment,
this symbol indicates that the product must not be disposed of as unsorted municipal waste, but
should be collected separately.
Refer to your local Olympus distributor in the EU for return and/or collection systems available in your
country.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

IMPORTANT

This manual pertains only to the operation of the LED illuminator stand. Please also read the
instruction manuals for the SZ2 series or applicable microscope to understand the comprehensive
operating instructions of the microscope system.

SAFETY PRECAUTIONS

1. After the equipment has been used in an observation of a specimen that is accompanied with a potential of infection,
clean the parts coming in contact with the specimen to prevent infection.

· Moving this product is accompanied with the risk of dropping the specimen. Be sure to remove the specimen before

moving this product.

· In case the specimen is damaged by erroneous operation, promptly take the infection prevention measures.

· The product becomes unstable if its height is increased by an accessory mounted on it. In this case, take anti-toppling

measures to prevent the specimen from being dropped when the product topples down.

2. When moving the microscope, hold the bottom of the base with one hand and the pillar with
the other hand, and carry the microscope without tilting it.

· Before carrying, remove the stage glass so that it will not drop during carrying.
Also remove other modules from the microscope as they may increase the weight and
increases danger.

3. LED (Light Emitting Diode) device is included in this product.

· Do not stare at the LED illumination (particularly the reflected illumination) light directly, as this may damage your eye.

· When a mirror or similar element is engaged in the illumination light path, take special care against the reflected light
that may enter your eye.

· Use of controls or adjustments performance of procedures other than those specified herein may result in hazardous
radiation exposure.

4. Always use the power cord provided by Olympus. If no power cord is provided, please select the proper power cord by
referring to the section “PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of this instruction manual. If the
proper power cord is not used, product safety performance cannot be warranted.

5. Always ensure that the grounding terminals are properly connected. If the equipment is not grounded, Olympus can no
longer warrant the electrical safety performance of the equipment.

6. If water or a liquid is spilt on the top of the LED illuminator stand, treat it quickly and properly as described in

2 Maintenance and Storage” below.

“

Safety Symbols

The following symbols are found on the equipment. Study the meaning of the symbols and always use the equipment in
the safest possible manner.

Symbol Explanation

Before use, carefully read the instruction manual. Improper use could result in personal injury to
the user and/or damage to the equipment.

Indicates the transmitted light illumination.

Indicates the reflected light illumination.

1

Indicates that the main switch is ON.

Indicates that the main switch is OFF.