Oki MC352, MC362, MC562, ES3452MFP, ES5462 MFP Startup Manual

Start-up Guide

This guide supports the following models:

MC352, MC362, MC562,

ES3452 MFP, ES5462 MFP

PREFACE

Every effort has been made to ensure that the information in this document is complete, accurate,
and up-to-date. The manufacturer assumes no responsibility for the result of errors beyond its
control. The manufacturer also cannot guarantee that changes in software and equipment made by
other manufacturers and referred to in this manual will not affect the applicability of the information
in it. Mention of software products manufactured by other companies does not necessarily constitute
endorsement by the manufacturer.

While all reasonable efforts have been made to make this document as accurate and helpful as
possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness
of the information contained herein.

All rights reserved by Oki Data Corporation. No part of this document may be reproduced in any form
or by any means without prior written permission from Oki Data Corporation.

© 2012 Oki Data Corporation

OKI is a registered trademark of Oki Electric Industry Company, Ltd.

Energy Star is a trademark of the United States Environmental Protection Agency.

Microsoft, Windows, Windows Server, Windows Vista and Internet Explorer are registered trademarks of
Microsoft Corporation.

Apple, Macintosh, Mac and Mac OS are the registered trademarks of Apple Inc.

Other product names and brand names are registered trademarks or trademarks of their proprietors.

As an Energy Star Program Participant, the manufacturer has determined that this product meets the

Energy Star guidelines for energy efciency.

This product complies with the requirements of the Council Directives 2004/108/EC (EMC) and
2006/95/EC (LVD) and 1999/5/ EC (R&TTE), as amended where applicable on the approximation
of the laws of the member states relating to electromagnetic compatibility, low voltage and radio &
telecommunications terminal equipment.

The following cables were used to evaluate this product for EMC directive

2004/108/EC compliance, and congurations other than this may affect that compliance.

CABLE TYPE

Power 1.8
USB 5.0
LAN 15.0
Telephone 3.0

LENGTH

(METER)

CORE SHIELD

8 8

8 4

8 8

8 8

- 2 -

EMERGENCY FIRST AID

Exercise care in the handling and use of toner powder:

If swallowed, give small amounts of cold water and seek medical attention. DO NOT attempt

to induce vomiting.

If inhaled, move the person to an open area for fresh air. Seek medical attention.

If it comes into contact with the eyes, ush with large amounts of water for at least 15 min-

utes keeping eyelids open. Seek medical attention.

Spills on clothing or exposed skin should be washed with cold water and soap to help reduce

risk of staining.

MANUFACTURER

Oki Data Corporation,

4-11-22 Shibaura, Minato-ku,

Tokyo 108-8551,

Japan

For all sales, support and general enquiries contact your local distributor.

IMPORTER TO THE EU/AUTHORISED REPRESENTATIVE

OKI Europe Limited (trading as OKI Printing Solutions)

Blays House

Wick Road

Egham

Surrey, TW20 0HJ

United Kingdom

For all sales, support and general enquiries contact your local distributor.

ENVIRONMENTAL INFORMATION

- 3 -

●● For Your Safety

Read the Start-up Guide (this guide) and User’s Guide for your safety before using the product.

Cautions related to safety

WARNING

CAUTION

Indicates the presence of a hazard for which not following the instructions noted may result
in serious injury or death.

Indicates the presence of a hazard for which not following the instructions noted may result
in injury.

General cautions

Do not touch the safety
switch inside the machine.
Doing so may cause electric
shock due to high voltage.
In addition, gears can rotate,
which may result in personal
injury.

Remove the power plug from
the socket and contact a
customer’s service center if
a liquid such as water comes
into contact with the internal
parts of the machine. Failure

to do so may cause re.

Remove the power cord
and contact a customer’s
service center if the machine
is dropped or the cover is
damaged.
Failure to do so may cause

electric shock and/or re

leading to injury.

Do not insert materials into a
vent holes.
Doing so may cause electric

shock and/or re resulting in

injury.
Do not throw toner or image

drum cartridges into re.

Doing so may cause dust
explosion leading to burns.

WARNING

Do not use inammable

sprays near the machine.
Doing so may result in

re due to heat within the

machine.

Remove the power plug
from the socket and remove
foreign material such as
clips if they fall inside the
machine. Failure to do so
may cause electric shock

and/or re leading to injury.

Remove the power cord
periodically to clean the
plug blades and root section
between the blades.
If the power plug remains
inserted for a long period of
time, the root section will
become dusty resulting in a

short which may cause re.

Do not place containers with
liquids such as water on the
machine.Doing so may cause

electric shock and/or re

resulting in injury.
Do not use power cords,

cables, or ground wires other
than those that are indicated
in the User’s Manual.

Doing so may cause re.

If the machine casing gets
extremely hot or if smoke,
unusual odour or abnormal
noises are emitted from the
machine, there is a risk of

re. Switch off and unplug

the mains connector and
contact your dealer.

Do not operate and do not
disassemble the machine
other than as directed in the
User’s Manual.
Doing so may cause electric

shock and/or re leading to

injury.
Do not clean spilled toner

with a vacuum cleaner.

Doing so may result in re

due to the sparks from
electric contact.

Toner spilled on the oor

should be wiped off with a
wet cloth.

Do not touch the fuser and
other parts when opening the
cover of the machine.
Doing so may cause burns.

The operation of UPS
(uninterruptible power
source) or inverters is not
guaranteed. Do not use
uninterruptible power source
or inverters.

Doing so may cause re.

CAUTION

Do not come closer to the paper’s exit area when
the power is turned on, while printing.
Doing so may result in personal injury.

- 4 -

Do not touch the liquid-crystal display if
damaged. If liquid (liquid crystal) leaked from
the liquid-crystal display comes into contact with

the eyes or mouth, ush with a large amount of

water. Seek medical attention if necessary.

Table of Contents

PREFACE ................................................................................................2

EMERGENCY FIRST AID ...........................................................................3

MANUFACTURER .....................................................................................3

IMPORTER TO THE EU/AUTHORISED REPRESENTATIVE ................................3

ENVIRONMENTAL INFORMATION ...............................................................3

For Your Safety ....................................................................................... 4

About This Guide ....................................................................................8

1 Machine Setup ................................................................... 10

Names of Components ........................................................................... 10

Machine ................................................................................................................. 10

Operator Panel ....................................................................................................... 12

Installing Your Machine .......................................................................... 13

Installation Requirements ........................................................................................ 13

Installation Environment ....................................................................................................13

Installation Space .............................................................................................................13

Unpacking and Installing Your Machine ...................................................................... 14

Available Options .................................................................................................... 16

Turning Your Machine On and Off .............................................................................. 17

Power Supply Conditions ....................................................................................................17

Turning On Your Machine .................................................................................................... 18

Turning Off Your Machine ....................................................................................................18

Loading Paper ........................................................................................................ 19

Step 1 Loading Paper into Tray 1 ......................................................................................... 19

Step 2 Conguring the Settings for Tray 1 ............................................................................ 20

Printing Conguration ............................................................................ 21

Printing Procedure .................................................................................................. 21

2 Copying ............................................................................. 22

Starting a Copy Job ................................................................................................. 22

- 5 -

Table of Contents

3 Faxing (For MC362, MC562, ES5462 MFP only) .................. 24

Initial Setup for Faxing .......................................................................... 25

Step 1 Setting Country Code .................................................................................... 25

Step 2 Connecting a Telephone Line .......................................................................... 26

Connecting to a Public Line (Connecting for Fax Only) ............................................................26

Connecting to a Public Line (Connecting for Fax and Telephone) .............................................. 27

Connecting to an ADSL Environment .................................................................................... 28

Connecting to an IP Telephone ............................................................................................ 28

Connecting to a CS Tuner or Digital Television .......................................................................29

Connecting to a PBX, Home Telephone or Business Phone ....................................................... 29

Connecting as an Internal Telephone .................................................................................... 30

Step 3 Conguring Basic Settings .............................................................................. 30

Step 3-1 Settings for Each Dialing Type ................................................................................ 30

Step 3-2 Setup of Date/Time ..............................................................................................31

Step 3-3 Specifying Sender Information ...............................................................................33

Step 3-4 PBX Connecting ...................................................................................................34

Step 3-5 Setting for Super G3 ............................................................................................. 35

Step 3-6 Specifying Reception Mode ....................................................................................36

Faxing ................................................................................................. 38

Procedure for Fax .................................................................................................... 38

Receiving a Fax ...................................................................................................... 40

Reception Behavior ............................................................................................................40

Printing Received Faxes ...................................................................................................... 40

Faxing from a Computer (For Windows) ................................................... 41

Installing a Fax Driver ............................................................................................. 41

Procedure for Fax from a Computer ........................................................................... 48

- 6 -

Table of Contents

4 Scanning ............................................................................ 49

Scanning to E-mail ................................................................................ 49

Initial Setup for Scan to E-mail ................................................................................. 49

Step 1 Conguring the Network Settings of Your Machine ....................................................... 49

Step 2 Conguring the E-mail Settings of Your Machine .......................................................... 53

Procedure of Scan to E-mail ..................................................................................... 56

Scanning to Network PC ......................................................................... 58

Initial Setup for Scan to Network PC .......................................................................... 58

Step 1 Conguring the Network Settings of Your Machine ....................................................... 58

Step 2 Setting Up Your Computer and Machine for Scan to Network PC..................................... 61

Procedure for Scan to Network PC ............................................................................. 72

Scanning to Local PC ............................................................................. 73

Initial Setup for Scan to Local PC .............................................................................. 73

For Windows ..................................................................................................................... 73

For Mac OS X ....................................................................................................................84

Procedure for Scan to Local PC ................................................................................. 90

5 Printing ............................................................................. 95

Printing from a Computer ....................................................................... 95

Installing a Printer Driver ......................................................................................... 95

For Windows ..................................................................................................................... 95

For Mac OS X .................................................................................................................. 103

Starting a Print Job ................................................................................................114

For Windows PCL/PCL XPS Printer Driver ............................................................................ 114

For Windows PS Printer Driver........................................................................................... 114

For Mac OS X PS Printer Driver.......................................................................................... 115

Index .................................................................................... 117

- 7 -

●● About This Guide

Terms in this document

The following terms are used in this guide:

Note

● Indicates important information on operations. Please ensure you read these.

Memo

● Indicates additional information on operations. It is recommended that this be read.

Reference

● Indicates where to look when you require more detailed or related information.

WARNING

● Indicates the presence of a hazard for which not following the instructions noted may result in serious injury or death.

CAUTION

● Indicates the presence of a hazard for which not following the instructions noted may result in injury.

Symbols in this document

The following symbols are used in this guide:

Symbols Description

[ ] ● Indicates menu names on the display screen.

● Indicates menu, window, dialog box names on the computer.

● Indicates part names of the machine or supplied parts.

" " ● Indicates messages and text entered on the display screen.

● Indicates le names on the computer.

● Indicates reference titles.
< > key Indicates a hardware key on the operator panel or a key on the keyboard of the computer.
> ● Indicates how to get to the menu you want on the menu of the machine or the computer.

● Indicates how to get to the section where the related information is described.

- 8 -

Notation used in this guide

The following notations may be used in this manual.

● PostScript3 Emulation → PSE, POSTSCRIPT3 Emulation, POSTSCRIPT3 EMULATION

● Microsoft

● Microsoft

● Microsoft

● Microsoft
version) *

● Microsoft

● Microsoft
version) *

● Microsoft

● Microsoft

● Microsoft

● Microsoft

● Microsoft

®

Windows® 7 64-bit Edition operating system → Windows 7 (64bit version) *

®

Windows Vista® 64-bit Edition operating system → Windows Vista (64bit version) *

®

Windows Server® 2008 R2 64-bit Edition operating system → Windows Server 2008 *

®

Windows Server® 2008 64-bit Edition operating system → Windows Server 2008 (64bit

®

Windows® XP x64 Edition operating system → Windows XP (x64 version) *

®

Windows Server® 2003 x64 Edition operating system → Windows Server 2003 (x64

®

Windows® 7 operating system → Windows 7 *

®

Windows Vista® operating system → Windows Vista *

®

Windows Server® 2008 operating system → Windows Server 2008 *

®

Windows® XP operating system → Windows XP *

®

Windows Server® 2003 operating system → Windows Server 2003 *

● Generic name for Windows 7, Windows Vista, Windows Server 2008, Windows XP, and Windows
Server 2003 → Windows

● Web Services on Devices → WSD

* If there is no special description, 64bit version is included in Windows 7, Windows Vista, Windows

Server 2008, Windows XP, and Windows Server 2003. (64bit version and Windows Server 2008 R2
is included in Windows Server 2008.)

If there is no special description, Windows 7 is used as Windows, Mac OS X 10.7 is used as Mac OS X,
and MC562 is used as the machine for examples in this document.

The descriptions in this document may be different depending on your OS or model.

- 9 -

1 Machine Setup

1

This chapter explains the initial setup for the machine, including the names of the machine

Machine Setup

components, how to unpack and install the machine, how to turn on/off the machine, and how to load
paper into tray 1.

●● Names of Components

This section shows the names of the components of the machine and operator panel.

Machine

The following shows the names of the machine
components.

7

13

6

5

4

3

2

1

No. Name

1 Top cover
2 Power switch
3 Tray 1
4 Multipurpose (MP) tray
5 Top cover open button
6 Operator panel
7 Auto document feeder (ADF) cover
8 Document tray
9 Scanner unit
10 Document glass cover
11 Air vents
12 USB port

11

12

8
9
10

No. Name

13 Document glass

20

19

No. Name

14 Fuser unit
15 Toner cartridge (Y: yellow)
16 Toner cartridge (M: magenta)
17 Toner cartridge (C: cyan)
18 Toner cartridge (K: black)
19 Image drum unit
20 LED head (four heads)

14
15

16

17

18

- 10 -

Names of Components

LINE TEL

24

21

22

23

25

No. Name

21 Faceup stacker
22 AC power socket
23 Air vents
24 LINE connection (for MC362/MC562/ES5462

MFP only)

25 TEL connection (for MC362/MC562/ES5462

MFP only)

1

Machine Setup

No. Name

26 Network interface connection
27 USB interface connection
28 SD memory card slot

(for MC562/ES5462 MFP only)

27
28

26

- 11 -

Names of Components

Operator Panel

1

The following shows the names of the components of the operator panel.

Machine Setup

Reference

● For the details on the functions of each component, refer to the User’s Guide > “Introduction” > “Control panel”.

22

2

19

161

11

13

6

15

7

9

8

12

14

10

17

No. Name

1 Display screen
2 Main function keys

<COPY> key
<SCAN> key
<PRINT> key
<FAX> key

(for MC362/MC562/ES5462 MFP)
3 <START (MONO)> key
4 <START (COLOR)> key
5 <STOP> key
6 <STATUS> key
7 <SETTING> key
8 <?HELP> key
9 <RESET/LOG OUT> key
10 Ten-key pad
11 <UP> key
12 <DOWN> key
13 <LEFT> key
14 <RIGHT> key
15 <OK> key
16 <BACK> key
17 <CLEAR> key
18 <POWER SAVE> key
19 <DATA IN MEMORY> indicator

(for MC362/MC562/ES5462 MFP)
20 One-Touch key pad
21 <JOB MACRO> key

(for MC562/ES5462 MFP)
22 Qwerty keyboard

(for MC562/ES5462 MFP)

21

3

20

4

5 18

- 12 -

Installing Your Machine

●● Installing Your Machine

This section explains how to unpack and install the machine.

Installation Requirements

This section explains the required environment
and space for machine installation.

Installation Environment

Your machine must be installed in the following
environment:

Temperature: 10°C~32°C
Humidity: 20%~80% RH (relative

humidity)

Maximum wet bulb
temperature: 25°C

Note

● Be careful of condensation. It may cause a malfunction.

● If installing your machine where the relative humidity of

the surrounding air is less than 30%, use a humidier or

antistatic mat.

Installation Space

Install your machine on a at surface that is

wide enough to accommodate the machine.

Allow for enough room around your machine
according to the images below.

● Top view

● Side view

60cm

1

Machine Setup

20cm

100cm

20cm

60cm

WARNING

● Do not place in hot locations or near re.

● Do not install in locations where chemical
reactions take place (laboratory etc.).

● Do not place in locations near ammable solutions
such as alcohol and thinner.

● Do not place in locations within reach of small
children.

● Do not install in unstable locations (wobbly stand,
angled place, etc.).

● Do not install in locations with high humidity or
dust and where exposed to direct sunlight.

● Do not install in an environment exposed to briny
air and corrosive gas.

● Do not install in locationss with much vibration.

● Do not install in locations where the ventilation
holes of the machine are blocked.

CAUTION

● Do not place directly on a rug or carpet with long
strands.

● Do not install in a closed room with poor
ventilation or circulation.

● If you use the machine in a small room for a long
time, please make sure that you ventilate the
room.

● Install away from strong magnetic elds and
sources of noise.

● Install away from monitors or TVs.

● When moving the machine, hold it on both sides,
and move it by slightly tilting the back down.

- 13 -

Installing Your Machine

Unpacking and Installing Your

1

Machine

Machine Setup

This section explains how to unpack and install
the machine.

Note

● The image drum is very delicate. Handle it carefully.

● Do not expose the image drum to direct sunlight or very
bright interior light (approximately more than 1500lux).
Even under the normal interior light, do not leave it for
more than 5 minutes.

● Packaging and cushioning material are needed if
transporting the machine. Do not throw them away.

1 Remove your machine from the box and

remove cushioning materials and the
plastic bag from your machine.

The accessories (an AC cord, Telephone cable and
the “Software DVD-ROM”) are packed within the
cushioning material (1).

Note

● Telephone cable is not supplied in some countries.

3 Remove the protection tapes (2) at the

top and sides of your machine, and take
out cushioning materials (3).

2

3

2

4 Remove the protection tapes (4), and

open the MP tray.

1

2 Lift your machine and place it where it is

to be installed.

Note

● Do not open the scanner unit till step 9 is completed.

4

5 Remove the protection tape (5), and pull

the paper up.

5

6 Close the MP tray.

7 Open the document glass cover.

- 14 -

Installing Your Machine

8 Remove the protection tapes (6).

Open the ADF and remove the protection tapes.

6

9 Close the document glass cover.

Now, you can open or close the scanner.

10 Open the scanner unit.

12 Press the top cover open button (8) and

open the top cover.

8

13 Remove the protective sheets (9).

9

1

Machine Setup

11 Remove the protection tapes (7), and

remove desiccants and lms.

7

14 Remove the orange stopper (11) while

pressing the blue lever of the fuser unit
(10) in the direction of the arrow.

10

9

Note

● Keep the orange stopper, it is necessary to transport
the machine.

11

- 15 -

Installing Your Machine

15 While pushing the right side of the toner

1

Machine Setup

cartridge, quickly slide the blue lock (12)
to the left side to lock it.
Slide the locks on all 4 toner cartridges.

12

16 Close the top cover.

17 Close the scanner unit.

Reference

● Please refer to “Loading Paper” P.19 for information on
how to load paper into the machine.

Available Options

The following option is available for your
machine:

● Second tray unit (tray 2)

● Additional RAM (256 MB or 512 MB)

● 16 GB SD card (MC562/ES5462 MFP only)

Reference

● For details on how to install the option, refer to the User’s
Guide > “Installing upgrades”.

● An SD card is used as a storage for spooling when copying
sectors, saving secure print/encrypted print data, as a
storage destination for form data, and for saving auto
delivery and transmission data.

For information on secure print, encrypted secure print,

form data, and auto delivery/transmission data storage

functions, please refer to Conguration Guide.

Memo

● There is a 4 GB SD card inside the MC562dn/ES5462 MFP.

If you expand the memory capacity, please replace with

an optional 16 GB SD card.

- 16 -

Installing Your Machine

Turning Your Machine On and Off

This section explains how to turn the machine on
and off.

Power Supply Conditions

The power supply must meet the following
conditions:

Current: 220 - 240VAC

(Range 198 - 264VAC)

Frequency: 50/60 Hz ± 2%

Note

● If the power supply is unstable, use a voltage regulator.

● The maximum power consumption of this machine is

1170W. Ensure that the power supply is sufcient to

operate this machine.

● We do not guarantee the operation where an
uninterruptible power system (UPS) or inverter is used.
Do not use an uninterruptible power system (UPS) or
inverter.

WARNING

● Be sure to turn off the power switch when
attaching or removing the AC cable and earth
wire.

● Be sure to connect the earth wire to a dedicated
grounding terminal.

● Never connect the earth wire to a water pipe, gas
pipe, telephone line earth, lightning rod or the
like.

● Make sure to connect the earth wire before
connecting the AC cable to the electric socket.

● Be sure to plug in and unplug the AC cable while
holding on to the power supply plug.

● Insert the power supply plug deep into the wall
socket securely.

● Do not insert or remove the power supply plug
with a wet hand.

● Install the power cord in a place where it will not
be stepped on, and do not place anything on the
power cord.

● Do not tie the cord in a bundle.

● Do not use the power cord if damaged.

● Do not use multi-outlet adapters.

● Do not connect this machine and other electric
items to the same wall socket. If connected
simultaneously with an air-conditioner unit, a
copy machine, shredder, etc., electric noise may
interfere with machine operation. If connection
to the same wall socket as another item is

unavoidable, please use a commercial noise lter

or a commercial noise cut transformer.

● Use the attached power cord and insert it directly
with the ground terminal. Do not use power cords
for other products for the machine.

● Do not use an extension cord. When use of an
extension cord is unavoidable, use a cord rated
15A or higher.

● Use of an extension cord may cause the machine
to operate at lower than normal capacity due to
AC voltage descent.

● During printing, do not shut off the power supply
or remove the power supply plug.

● When not in use for extended periods
(consecutive holidays or extended travel), remove
the power cord from the socket.

● Do not use the attached power cord for other
products.

There is a risk of electric

shock and/or re.

1

Machine Setup

- 17 -

Installing Your Machine

Turning On Your Machine

1

1

Plug the AC cord into the AC power

Machine Setup

socket of your machine.

2 Plug the AC cord into the electric socket.

3 Check that no documents are on the

document glass or ADF, and that the
ADF cover is closed.

4 Hold down the power switch for

approximately one second to turn the
power on.

Turning Off Your Machine

1

Hold down the power switch for
approximately one second.

Note

● Press the power switch for less than 5 seconds.

The message [Shutdown in progress. Please
wait. The machine turns off automatically.]
will appear in the operator panel, and power
switch indicator will blink every 1 second. The
machine then turns off automatically and the
power switch indicator extinguishes.

The copy standby screen is displayed after your
machine attains ready status.

Note

● Wait a few seconds after turning the power on or off
before turning the power on or off again.

Note

● Wait a few seconds after turning the power on or off
before turning the power on or off again.

Reference

● Your machine has a power save mode and sleep mode,
and an auto power off function. For details, refer to the
User’s Guide > “Getting started” > “Power saving mode” /
“Sleep mode” / “Auto power off”.

- 18 -

Installing Your Machine

Loading Paper

Your machine has two built-in trays (tray 1 and MP tray) and an optional tray (tray 2).

This section explains the supported paper and capacity of tray 1 and how to load paper into the tray 1.
After you load paper, you need to register the loaded paper on your machine.

To complete the loading procedures, follow the 2 steps below:

● “Step 1 Loading Paper into Tray 1” P.19

● “Step 2 Conguring the Settings for Tray 1” P.20

 Tray 1 Specication

Supported paper size Paper capacity Paper weight

● A4

● A5*

● B5

● A6*

● Letter

● Legal 13

● Legal 13.5

● Legal 14

● Executive

● 16K (184 x 260 mm)

● 16K (195 x 270 mm)

● 16K (197 x 273 mm)

● Postcard

● Custom

250 sheets

(when paper weight is 80 g/m2)

● Light

64 to 74 g/m2 (17 to 19 lb)

● Medium

2

75 to 104 g/m

● Heavy

105 to 120 g/m

● Ultra Heavy1

121 to 176 g/m

● Ultra Heavy2

177 to 220 g/m

(20 to 27 lb)

2

(28 to 32 lb)

2

(33 to 46 lb)

2

(47 to 58 lb)

1

Machine Setup

Note

● Duplex printing cannot be performed on paper marked with “*”.

Reference

● For the specications and how to load paper in tray 2 (optional), MP tray, refer to the User’s Guide > “Loading paper”.

Step 1 Loading Paper into Tray 1

2 Slide the paper guide (1) to the width of

the paper to be loaded.

1

Pull out tray 1.

1

3 Slide the paper stopper (2) to the length

of the paper to be loaded.

2

- 19 -

Installing Your Machine

4 Flex paper back and forth, and then fan

1

Machine Setup

it. Straighten the edges of the paper
stack on a level surface.

5 Load paper with the print side face

down.

Note

● Do not load paper above the ll line (3).

2 Press the to select [Paper Setup] and

then press OK.

3 Check that [Tray 1] is selected and then

press OK.

4 Check that [Paper Size] is selected and

then press OK.

5 Press the to select the size of the

loaded paper and then press OK.

Reference

● If [Custom] is selected for [Paper Size], you need
to register the custom size. For how to register the
custom size, refer to the User’s Guide > “Loading
paper” > “Registering custom sizes”.

[ ▼ ▼ ▼ ]

3

6 Push tray 1 until it stops.

Step 2 Conguring the Settings for
Tray 1

1

Press the <SETTING> key on the
operator panel.

6 Press the to select [Media Type] and

then press OK.

7 Press the to select the type of media

loaded and then press OK.

8 Press the to select [Media Weight]

and then press OK.

9 Press the to select the weight of the

loaded paper and then press OK.

10 Press the until the top screen is

displayed.

- 20 -

Printing Conguration

●● Printing Conguration

This section explains how to print the Conguration on which you can check the detailed information of

your machine, such as the settings and status of your machine.

When you nished the initial setup, follow the procedure below to conrm that the machine is properly

installed.

Printing Procedure

1 Press the <SETTING> key on the

operator panel.

1

Machine Setup

2 Check that [Reports] is selected and

press OK.

3 Check that [Conguration] is selected

OK

and press

.

4 For the conrmation message, check

that [Yes] is selected and press OK.

When the Conguration is properly printed, the

initial setup has succeeded.

- 21 -

2 Copying

This chapter explains the basic operation for your machine’s copy function.

2

Starting a Copy Job

Copying

Memo

● The following procedure uses the factory default settings.

1 Press the <COPY> key on the operator

panel to open the copy standby screen.

● Document Glass

Place the document face down and align its top
edge to the upper-left corner of the glass.

Close the document glass cover gently.

Note

● Do not apply an excessive load to the document
glass.

2 Place your document in the ADF or on

the document glass as below:

● ADF

Load documents face up with the top edge of the

documents in rst.

Adjust the document guides to the width of your
documents.

Memo

● The machine prioritizes the ADF when copying
documents. Be sure not to place documents on the
ADF when you use the document glass.

Note

● If Carriage Error <02> is displayed, press Power
OFF/ON.

- 22 -

Starting a Copy Job

3 Press

Reference

● To load a landscape document, refer to the User’s Guide >
“Operation” > “Loading document(s)”.

● You can change the copy settings such as scan size,
document’s orientation and duplex copying as necessary.
For details, refer to the User’s Guide > “Copying” >
“Advanced operation”.

MONO

Memo

● You can cancel the operation by pressing the
<STOP> key on the operator panel until the
message showing the copy completion is displayed.

or

to start copying.

COLOR

2

Copying

- 23 -

3 Faxing (For MC362, MC562,

ES5462 MFP only)

This chapter explains the initial setup, such as how to set the country code, connect a telephone line

and congure the basic settings, and basic procedure for the Fax and Fax from Computer functions.

Your machine supports the following functions regarding fax.

3

“Faxing” Scans documents and transmits them as faxes or receives faxes via a telephone line.

Faxing (For MB362, MB562, ES5462 MFP only)

“Faxing from a Computer

(For Windows)”

Internet Faxing Scans documents and transmits them as faxes or receives faxes by e-mails via

Auto Delivery
(MC562/ES5462 MFP

only)

Function Overview

You need to complete the initial setup for faxing before using this function.
Transmits faxes from your computer connected via USB or network. The faxes are

transmitted directly from your computer to a destination via the machine using a
telephone line. The fax driver must be installed on the computer to use this function.
You also need to complete the initial setup for faxing before using this function.

network.
For the initial setup for the function, refer to the Conguration Guide > “Conguring
the network settings” > “Setting up scan to e-mail and internet fax”.
For the procedure for the function, refer to the User’s Guide > “Internet fax” >
“Sending a fax from your PC” > “Basic operation”.

Forwards the received faxes and les attached to e-mails automatically to specied
destinations. You can specify e-mail addresses and a network folder as the
destination.
For the initial setup for the function, refer to the Conguration Guide > “Conguring
the network settings” > “Setting up scan to e-mail and internet fax” / “Setting up
scan to network PC”.

- 24 -

Initial Setup for Faxing

●● Initial Setup for Faxing

This section explains the initial setup necessary for the Fax and Fax from Computer functions.

To set up the machine for the Fax and Fax from Computer functions, follow the 3 steps below:

● “Step 1 Setting Country Code” P.25

● “Step 2 Connecting a Telephone Line” P.26

● “Step 3 Conguring Basic Settings” P.30

Step 1 Setting Country Code

This section explains how to set the country

code. Be sure to select the suitable country code
before connecting the telephone line.

Note

● If you set wrong country code, you may not be able to
send or receive faxes. When you cannot send or receive
faxes even though you have properly connected the
telephone line, check if [Country Code] is set correctly.

1 Hold down the power switch for

approximately one second to turn on the
power.

3 Press the to select [Admin Setup]

and then press OK.

4 Enter the administrator password.

The factory default password is “aaaaaa”.

a Press , , , to select the

character you want, and then
press OK.

3

Faxing (For MB362, MB562, ES5462 MFP only)

2 Press the <SETTING> key on the

operator panel.

- The selected character is entered as “*” in

the text led.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter

the correct value.

b Repeat step a until all characters

required are entered.

c Press the and to select [Enter]

and press OK.

- 25 -

Initial Setup for Faxing

5 Press the to select [Fax Setup] and

then press OK.

6 Press the to select [Fax Setting] and

then press OK.

7 Press the to select [Country Code]

OK

and then press

.

8 Press the or to select your country

3

Faxing (For MB362, MB562, ES5462 MFP only)

name and then press

If your country name is not displayed, select the
following value.

- If your country is the Czech Republic or
Slovakia, select [Czech/Slovakia].

- If your country is Canada, select [U.S.A].

- If the region of your country is Latin

America, select [Latin America].

- If the region of your country is Europe or
the Middle East, select [International].

Settable Country Codes:
U.S.A. International United Kingdom

Ireland Norway Sweden Finland

Denmark Germany Hungary
Czech/Slovakia Poland Switzerland
Austria Belgium Netherlands France
Portugal Spain Italy Greece

Australia New Zealand Singapore

Hong Kong Latin America Mexico
China Russia Taiwan Japan Korea
Thailand Malaysia Jordan Argentina
Brazil South Africa Belarus Moldova
Turkey Ukraine

OK

.

9 For the conrmation message, check

that [Yes] is selected and press OK.

The machine restarts automatically, and the
default screen is displayed a few minutes later.

Memo

● If the [Country Code] is changed, the value of [PBX
Line] and [MF (Tone)/DP (Pulse)] are changed to the

default values for each country code.

Step 2 Connecting a Telephone Line

This section explains how to connect a telephone

line for faxing. Be sure to connect the telephone
line depending on your environment before you
transmit or receive faxes.

The method of connecting a telephone line
differs depending on your environment. Based
on the following gures, connect the line for
your environment.

Note

● Do not connect with USB cable or LAN cable at this point.

● Be sure to set the appropriate country code before

connecting the telephone line.

● You cannot connect to an ISDN line directly. To connect to
an ISDN line, use the terminal adopter (TA) and connect
to the LINE connection of the machine.

● A telephone cable is supplied with your machine except in
certain countries.

Reference

● To check the reception mode according to the machine
environment, refer to “Step 3-6 Specifying Reception

Mode” P.36.

● To check the dial type settings, refer to “Step 3-1 Settings

for Each Dialing Type” P.30.

Connecting to a Public Line (Connecting for Fax Only)

Note

● Do not connect with USB cable or LAN cable at this point.

1 Check that the machine is turned off.

If the machine is turned on, hold down the power
switch for approximately one second to turn off
the power.

- 26 -

Initial Setup for Faxing

2 Plug one end of the [Telephone cable]

into the [LINE connection] of your
machine and the other end into the
[Public Line (Analog)].

LINE connection

Public Line

(Analog)

Telephone cable

Note

● Be certain to connect the telephone cable to [LINE
connection]. Never connect it to [TEL connection].

3 Remove the [Telephone connector

cover].

TEL

LINE

Telephone connector cover

4 Plug the external telephone’s cable into

the [TEL connection] of your machine.

TEL connection

3

Faxing (For MB362, MB562, ES5462 MFP only)

Connecting to a Public Line (Connecting for Fax and Telephone)

Note

● Do not connect with USB cable or LAN cable at this point.

1 Check that the machine is turned off.

If the machine is turned on, hold down the power
switch for approximately one second to turn off
the power.

2 Plug one end of the [Telephone cable]

into the [LINE connection] of your
machine and the other end into the
[Public Line (Analog)].

LINE connection

Public Line

(Analog)

The telephone that is connected to the machine
is called an external telephone.

Note

● Only one telephone can be connected to the machine.

● Do not connect the telephone to the machine in parallel.

If you connect the telephone to the machine in parallel,
the following problems will occur and the machine will not
work correctly.

- When you send or receive a fax, the fax picture may
be broken or a communication error may occur by
picking up the telephone.

- The fax transfer function is not able to work from the
external telephone.

Public Line (Analog) Public Line (Analog) rst oor second oor

Telephone cable

Memo

● In the case of direct interconnection, separate
construction is necessary. Please contact the telephone
company that you use.

- 27 -

Initial Setup for Faxing

Connecting to an ADSL Environment

Note

● Do not connect with USB cable or LAN cable at this point.

First, check that the machine is turned off. If
the machine is turned on, hold down the power
switch for approximately one second to turn off
the power.

Plug the [Telephone cable] connected to the
ADSL modem into the [LINE connection] of
your machine.

3

Remove the telephone connector cover.

Faxing (For MB362, MB562, ES5462 MFP only)

Plug the external telephone’s cable into the [TEL
connection] of your machine.

LINE connection

Telephone cable

TEL connection

Splitter

ADSL modem

Public Line

(Analog)

Connecting to an IP Telephone

Note

● Do not connect with USB cable or LAN cable at this point.

First, check that the machine is turned off. If
the machine is turned on, hold down the power
switch for approximately one second to turn off
the power.

Plug the
IP telephone into the [LINE connection] of

your machine.

Remove the telephone connector cover.

Plug the external telephone’s cable into the

[TEL connection] of your machine.

LINE connection

Telephone cable

[Telephone cable] connected to the

TEL connection

Optical IP telephone

Corresponding

telephone

Optical Network
Unit (ONU)

LAN
cable

*Insert into the

telephone cable jack.

Optical cable

Memo

● Check the dial tone detection if it is unable to dial. Refer to
the Conguration Guide > “Appendix A - menu system” >
“Admin Setup” > “User Install”.

● If you cannot send or receive faxes very well, set [Super
G3] to [OFF]. Refer to “Step 3-5 Setting for Super G3”

P.35 in detail.

Memo

● Check the dial tone detection if it is unable to dial.
the Conguration Guide > “Appendix A - menu system” >
“Admin Setup” > “User Install”.

● If you cannot send or receive faxes very well, set [Super
G3] to [OFF]. Refer to “Step 3-5 Setting for Super G3”

P.35 in detail.

Refer to

- 28 -

Initial Setup for Faxing

Connecting to a CS Tuner or Digital Television

Note

● Do not connect with USB cable or LAN cable at this point.

First, check that the machine is turned off. If
the machine is turned on, hold down the power
switch for approximately one second to turn off
the power.

Plug the

the [Public Line (Analog)] into the [LINE

connection] of your machine.

Remove the telephone connector cover.

Plug the telephone cable connected to the
CS tuner or digital television into the [TEL
connection] of your machine.

LINE connection

[Telephone cable] connected to

TEL connection

Connecting to a PBX, Home Telephone or Business Phone

Note

● Do not connect with USB cable or LAN cable at this point.

First, check that the machine is turned off. If
the machine is turned on, hold down the power
switch for approximately one second to turn off
the power.

Plug the [Telephone cable] connected to
the [Public Line (Analog)] into the [LINE
connection] of your machine.

Remove the telephone connector cover.

Plug the telephone cable connected to a
control device including PBX, etc. into the [TEL
connection] of your machine.

LINE connection TEL connection

3

Faxing (For MB362, MB562, ES5462 MFP only)

Telephone cable

CS tuner or digital
television

Public Line

(Analog)

Control device
including PBX, etc.

Telephone cable

Public Line

(Analog)

● Home Telephone

In general, many telephones are connected

with one or two telephone lines, and internal

communication and door phone are possible.
This is simple switching equipment for
household.

● Business Phone

In general, it can accommodate more than

two telephone lines, these telephone lines can

be shared with other telephones, and internal
communication is possible. This is simple
switching equipment.

- 29 -

Initial Setup for Faxing

Connecting as an Internal Telephone

Note

● Do not connect with USB cable or LAN cable at this point.

First, check that the machine is turned off. If
the machine is turned on, hold down the power
switch for approximately one second to turn off
the power.

Plug the [Telephone cable] connected to a
control device including PBX, etc. into the [LINE
connection] of your machine.

3

Faxing (For MB362, MB562, ES5462 MFP only)

LINE connection

Control device
including PBX, etc.

Telephone

cable

Public Line

(Analog)

Step 3 Conguring Basic

Settings

This section explains how to congure the basic
settings on the machine for the fax function.
Follow the 6 sub steps below:

● “Step 3-1 Settings for Each Dialing Type”

P.30

● “Step 3-2 Setup of Date/Time” P.31

● “Step 3-3 Specifying Sender Information”

P.33

● “Step 3-4 PBX Connecting” P.34

● “Step 3-5 Setting for Super G3” P.35

● “Step 3-6 Specifying Reception Mode” P.36

Note

● You need to complete the country code setting and
connect the telephone line according to your environment
before this procedure.

Memo

● You can skip the steps 3-4 and 3-5 depending on your
environment. For details, refer to each description.

Memo

● Set [PBX Line] to [ON]. Refer to “Step 3-4 PBX

Connecting” P.34 in detail.

Step 3-1 Settings for Each Dialing Type

Specify the dialing type for transmission
according to your environment. The factory
default for [MF (Tone)/DP (Pulse)] is set to
[Tone].

● For push-button phones, if you hear a “Beep,
boop, beep” sound, leave [MF (Tone)/
DP (Pulse)] as [Tone].

● For push-button type phones, if you do not
hear a “Beep, boop, beep” sound, set
[MF (Tone)/DP (Pulse)] to [Pulse].

● For rotary-dial type phones, set [MF (Tone)/
DP (Pulse)] to [Pulse].

1 Press the <SETTING> key on the

operator panel.

- 30 -

Initial Setup for Faxing

2 Press the to select [Admin Setup],

and press OK.

3 Enter the administrator password.

The factory default password is “aaaaaa”.

a Press , , , to select the

character you want, and then
press OK.

7 Press the until the top screen is

displayed.

Step 3-2 Setup of Date/Time

Set up Date/Time of your region.

1 Press the <SETTING> key on the

operator panel.

3

Faxing (For MB362, MB562, ES5462 MFP only)

2 Press the to select [Easy Setup] and

then press OK.

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter

the correct value.

b Repeat step a until all characters

required are entered.

c Press the and to select [Enter]

and press OK.

4 Press the to select [User Install],

and press OK.

3 Enter the administrator password.

The factory default password is “aaaaaa”.

5 Press the to select [MF (Tone)/DP

(Pulse)], and then press OK.

6 Press the to select a dial type, and

then press OK.

- 31 -

Initial Setup for Faxing

a Press , , , to select the

character you want, and then
press OK.

3

Faxing (For MB362, MB562, ES5462 MFP only)

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter

the correct value.

8 Press the or to select the current

date and then press OK.

To move to the next box, press the .

9 Press the or to select the current

time and then press OK.

To move to the next box, press the .

OK

When you press

Date/Time setting is complete appears.

, a message showing that

10 When the setup menu screen is

displayed, press to complete the
setup.

b Repeat step a until all characters

required are entered.

c Press the and to select [Enter]

and press OK.

4 Check that [Date/Time Setting] is

selected and then press the .

5 Press the to select the appropriate

OK

time zone and then press

.

6 Press the to select whether summer

time is applied or not and then press OK.

7 Check that [Manual] is selected and

then press OK.

11 For the conrmation message, check

OK

that [Yes] is selected and press

.

- 32 -

Initial Setup for Faxing

Step 3-3 Specifying Sender Information

Specify the fax number and sender name for
your machine. The information specied here is
printed on the top of the faxes you sent from the
machine.

1 Press the <SETTING> key on the

operator panel.

2 Press the to select [Easy Setup] and

press OK.

a Press , , , to select the

character you want, and then
press OK.

3

Faxing (For MB362, MB562, ES5462 MFP only)

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter

the correct value.

3 Enter the administrator password.

The factory default password is “aaaaaa”.

b Repeat step a until all characters

required are entered.

c Press the and to select [Enter]

and press OK.

4 Press the to select [Fax Setting] and

then press the .

5 Press to select the [Fax Number]

entry box.

- 33 -

Initial Setup for Faxing

6 Enter the fax number of your machine

with the ten-key pad.

3

Faxing (For MB362, MB562, ES5462 MFP only)

7 Check that [Enter] is selected and then

press OK.

8 Press to select the [Sender ID] entry

box.

Step 3-4 PBX Connecting

When connecting to PBX (internal exchange), set
[PBX Line] to [ON].

1 Press the <SETTING> key on the

operator panel.

2 Press the to select [Admin Setup]

and then press OK.

9 Enter an arbitrary sender name up to 22

characters allowed.

10 Press the and to select [Enter] and

then press OK.

The message showing that fax setting is complete
appears.

11 When the setup menu screen is

displayed, press to complete the
setup.

12 For the conrmation message, check

that [Yes] is selected and press OK.

3 Enter the administrator password.

The default password is “aaaaaa”.

a Press , , , to select the

character you want, and then
press OK.

- 34 -

Initial Setup for Faxing

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter

the correct value.

b Repeat step a until all characters

required are entered.

c Press the and to select [Enter]

and press

OK

.

4 Press the to select [Fax Setup] and

OK

then press

.

Step 3-5 Setting for Super G3

If you cannot send or receive faxes correctly
when the machine is connected to the ADSL
environment or an IP telephone, set [Super G3]
to [OFF].

1 Press the <SETTING> key on the

operator panel.

3

Faxing (For MB362, MB562, ES5462 MFP only)

2 Press the to select [Admin Setup]

and then press OK.

5 Press the to select [Fax Setting] and

then press OK.

6 Press the to select [PBX Line] and

then press

OK

.

7 Press the to select [ON] and then

press

OK

.

8 Press the until the top screen is

displayed.

3 Enter the administrator password.

The default password is “aaaaaa”.

a Press , , , to select the

character you want, and then
press OK.

- 35 -

Initial Setup for Faxing

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter

the correct value.

3

Faxing (For MB362, MB562, ES5462 MFP only)

b Repeat step a until all characters

required are entered.

c Press the and to select [Enter]

and press

4 Press the to select [User Install] and

then press

OK

.

OK

.

Step 3-6 Specifying Reception Mode

The optimal reception mode differs depending
on your machine’s environment. Check with the
following description.

● Fax Ready Mode

This mode is recommended when you use the
machine as a fax machine.

● Tel/Fax Ready Mode

This mode is recommended when you connect an
external phone to the machine.

● Ans/Fax Ready Mode

This mode is recommended when you connect an
external answering machine to the machine.

● Tel Ready Mode

This mode is recommended when you mainly use
an external phone connected to the machine.

● DRD

This mode is recommended when you use the
distinctive ring detection (DRD) function provided
by a telephone company.

5 Press the to select [Super G3] and

then press OK.

6 Press the to select [OFF] and then

press

OK

.

7 Press the until the top screen is

dislpayed.

1 Press the <SETTING> key on the

operator panel.

2 Press the to select [Admin Setup]

and press OK.

3 Enter the administrator password.

The factory default password is “aaaaaa”.

- 36 -

a Press , , , to select the

character you want, and then
press OK.

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter

the correct value.

Initial Setup for Faxing

3

Faxing (For MB362, MB562, ES5462 MFP only)

b Repeat step a until all characters

required are entered.

c Press the and to select [Enter]

and press OK.

4 Press the to select [User Install] and

press OK.

5 Press the to select [Reception Mode]

and press OK.

6 Press the to specify a reception mode

and press OK.

Settable Reception Mode:
Fax Ready Mode* Tel/Fax Ready Mode
Ans/Fax Ready Mode Tel Ready Mode DRD

*indicates the factory default.

7 Press the until the top screen is

displayed.

- 37 -

Faxing

●● Faxing

This section explains the basic procedure for the Fax function.

The Fax function enables you to scan documents and transmit them as faxes or receive faxes via a
telephone line.

Be sure to nish the initial setup before using this function.

Procedure for Fax

3

This section explains how to transmit faxes. The
following procedure uses the direct input method

Faxing (For MB362, MB562, ES5462 MFP only)

for specifying a destination.

You need to congure the initial settings before
using the Fax function.

Note

● Up to 40 digits can be entered for the destination fax
number.

Memo

● You can load only A4, letter, or legal size documents in
the ADF, and A4 or letter size documents on the document
glass.

● You cannot load mixed size documents for faxing.

● The following procedure uses the factory default settings.

1 Press the <FAX> key on the operator

panel.

● Document Glass

Place the document face down and align its top
edge to the upper-left corner of the glass.

Close the document glass cover gently.

Note

● Do not apply an excessive load to the document
glass.

2 Place your document in the ADF or on

the document glass as below:

● ADF

Load documents face up with the top edge of the
documents in rst.

Adjust the document guides to the width of your
documents.

Memo

● The machine prioritizes the ADF when scanning
documents. Be sure not to place documents on the
ADF when you use the document glass.

Note

● If Carriage Error <02> is displayed, press Power
OFF/ON.

3 Check that [Fax] is selected and

press OK to open the fax start screen.

- 38 -

Faxing

4 Check that [Add Destination] is

selected on the start screen and then
press

OK

.

5 Press the to select [Direct Input] and

then press OK.

6 Enter a destination fax number up to

40 digits using the ten-key pad on the
operator panel.

Reference

● For dialing functions such as hyphen, prex and
ash, refer to the User’s Guide > “Faxing - MC362,
MC562 AND ES5462 MFP only” > “Sending a fax from
the MFP” > “Advanced operation”.

7 Check that [Enter] is selected and then

press OK.

8 Press

Reference

● In addition to inputting the destination directly, you can
use the speed dial list, group list, transmission histories,
reception histories, or One-Touch key pad to specify
the destination. For details, refer to the User’s Guide
> “Faxing - MC362, MC562 AND ES5462 MFP only” >

“

Managing the phone book”.

● To load a landscape document, refer to the User’s Guide >
“Operation” > “Loading document(s)”.

● You can change the fax settings such as document size
and resolution as necessary. For details, refer to the
User’s Guide > “Faxing - MC362, MC562 AND ES5462
MFP only” > “Sending a fax from the MFP” > “Advanced
operation”.

● When you want to specify multiple destinations, refer to
the User’s Guide > “Faxing - MC362, MC562 AND ES5462
MFP only” > “Sending a fax from the MFP” > “Advanced
operation”.

MONO

Note

● You cannot use the

● If the <STATUS> key is pressed and

twice, the information is displayed on the display
screen.

Memo

● When you want to cancel the operation during the
transmission, press the <STOP> key on the operator
panel.

to start transmission.

button.

COLOR

is pressed

3

Faxing (For MB362, MB562, ES5462 MFP only)

- 39 -

Faxing

Receiving a Fax

This section explains how your machine behaves
when the machine whose reception mode is set
to [Fax Ready Mode] is receiving and printing
faxes.

Reference

● For the machine behavior when the reception mode is
set to other than [Fax Ready Mode], refer to the User’s
Guide > “Faxing - MC362, MC562 AND ES5462 MFP only” >

3

Faxing (For MB362, MB562, ES5462 MFP only)

“Sending a fax from the MFP” > “Fax receiving”.

Reception Behavior

Your machine is set by factory default to [Fax
Ready Mode] so that it automatically receives

faxes.

When the machine is receiving faxes, the

<DATA IN MEMORY> indicator is lit. If the
<STATUS> key is pressed and

twice, the information is displayed on the display
screen. Even if the reception is nished, the
indicator remains lit while the data is stored in
memory.

is pressed

Printing Received Faxes

The machine automatically prints out the
received fax. By factory default, tray 1 is set to
be used.

Note

● Do not pull out the paper trays when the machine is
printing.

Memo

● Use only standard or recycled paper.

● Available paper sizes are A4, letter, or legal.

Reference

● Images larger than the specied paper are reduced,
discarded, or printed onto multiple sheets of paper
depending on the reception print settings. For details,
refer to the User’s Guide > “Faxing - MC362, MC562 AND
ES5462 MFP only” > “Sending a fax from the MFP” > “Fax
receiving” > “Printing received faxes”.

● If you want to use another paper tray to print received
faxes, refer to the User’s Guide > “Appendix A - menu
system” > “Paper setup” > “Select Tray”.

Memo

● If the memory is exceeded while the machine is receiving
data, the reception is cancelled. If this happens, print the
data stored in memory or wait until the stored sending/
receiving job nishes, and then ask the sender to resend
the fax.

- 40 -

Faxing from a Computer (For Windows)

●● Faxing from a Computer (For Windows)

This section explains how to install a fax driver and the basic procedure of sending a fax from a
computer. The fax driver allows you to send faxes directly from your computer to a destination via the
machine without printing the document.

Be sure to install the fax driver for MC362, MC562 or ES5462 MFP before faxing from a computer.

Note

● You need to nish the initial setup before using this function.

Installing a Fax Driver

This section explains how to install a fax driver
on your computer as the initial setup for Fax
from Computer function.

 Overview

 Connecting Methods

You can select either of the following connection
methods:

● “For Network Connection” P.41

● “For USB Connection” P.46

 Product Requirements

Your machine supports the following Windows
operating systems:

● Windows 7/Windows 7 (64bit Version)

● Windows Vista/Windows Vista (64bit Version)

● Windows Server 2008 R2

● Windows Server 2008/Windows Server 2008

(x64 Version)

● Windows XP/Windows XP (x64 Version)

● Windows Server 2003/Windows Server 2003

(x64 Version)

 For Network Connection

To install a fax driver on your computer via the
network connection, follow the 2 steps below:

● “Step 1 Conguring the Network Settings of

Your Machine” P.41

● “Step 2 Installing a Fax Driver” P.44

Note

● You need to complete the network setting of the computer
before this procedure.

Memo

● You can skip the step 1 if the IP address is already set on
your machine.

● You can skip the step 2 if the fax driver is already installed
on your computer.

 Step 1 Conguring the Network

Settings of Your Machine

Connect your machine to a network with an
Ethernet cable, and then congure the machine’s
IP address and other network information from
the operator panel. You can set the IP address
either manually or automatically.

If there is no DHCP server or BOOTP server on
the network, you need to manually congure the
IP address on the computer or machine.

If your network administrator or internet
service provider species a unique IP address
for the computer and your machine, set the IP
addresses manually.

Note

● When setting an IP address manually, ask the network
administrator or your internet service provider which IP
address to use. If the IP address is set incorrectly, the
network may go down or Internet access may be disabled.

● Conform the IP version of the machine to that of your
computer.

● Set [TCP/IP] setting to [Enable] on your machine. (By
factory default, it is set to [Enable].)

Memo

● If conguring a small network consisting of only your
machine and a computer, set IP addresses as shown
below (according to RFC1918).

For the computer

IP address : 192.168.0.1~254

Subnet mask : 255.255.255.0

Default gateway : not used

DNS server : not used

For the machine

IP Address Set : Manual

IPv4 Address : 192.168.0.1~254

(select a different value
from the computer)

Subnet Mask : 255.255.255.0

Gateway Address : 0.0.0.0

Network Scale : Small

● To set [Network Scale], press the <SETTING> key
and then select [Admin Setup] > [Network Menu] >
[Network Setup] > [Network Scale].

3

Faxing (For MB362, MB562, ES5462 MFP only)

- 41 -

Faxing from a Computer (For Windows)

1 Prepare an Ethernet cable and a hub.

Prepare an Ethernet cable (category 5, twisted
pair, straight) and a hub separately.

2 Hold down the power switch for

3

Faxing (For MB362, MB562, ES5462 MFP only)

approximately one second to turn off the
power. And turn off your computer.

4 Plug the other end of the Ethernet cable

into the hub.

5 Hold down the power switch for

approximately one second to turn on the
power.

3 Plug one end of the Ethernet cable into

the network interface connection on the
back of the machine.

6 Press the <SETTING> key on the

operator panel.

7 Press the to select [Easy Setup], and

press OK.

- 42 -

8 Enter the administrator password.

The factory default password is “aaaaaa”.

Faxing from a Computer (For Windows)

a Press , , , to select the

character you want, and then
press OK.

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter

the correct value.

11 Enter the IP address using the ten-key

pad, and press OK.

3

Faxing (For MB362, MB562, ES5462 MFP only)

To move to the next box, press the .

12 Enter the subnet mask using the ten-key

pad, and press OK.

To move to the next box, press the .

b Repeat step a until all characters

required are entered.

c Press the and to select [Enter]

and press OK.

9 Press the to select [Network

Setting], and then press the .

10 If setting the IP address manually, check

OK

that [Manual] is selected, and press

.

13 Enter the default gateway address using

the ten-key pad, and press OK.

To move to the next box, press the .

14 Enter the DNS server and WINS server if

needed.

If it is not necessary to connect the DNS server
or WINS server to the network, press OK until the
pop-up message showing setting completion is
displayed.

15 When the setup menu screen is

displayed, press to complete the
setup.

16 For the conrmation message, check

that [Yes] is selected and press OK.

If obtaining the IP address automatically, press
the to select [Auto], and press OK. Proceed to
step 15.

◆ Print the Network Information to check that
the IP address and other network information
are set properly.

- 43 -

Faxing from a Computer (For Windows)

1 Press the <SETTING> key on the

operator panel.

3

Faxing (For MB362, MB562, ES5462 MFP only)

2 Check that [Reports] is selected and

press OK.

3 Press the to select [System] and

press OK.

4 Press the to select [Network

OK

Information] and press

5 For the conrmation message, check

that [Yes] is selected and press

The Network Information is printed.

.

4 Select the device of your machine, and

then click [Next].

5 Read the license agreement and then

click [I Agree].

6 Read the “Environmental advice for

Users” and click [Next].

OK

.

 Step 2 Installing a Fax Driver

Note

● To complete this procedure, you must be logged in as an
administrator.

1 Check that your machine and the

computer are turned on and connected,
and then insert the “Software DVD-ROM”
into the computer.

2 Click [Run Setup.exe] after [AutoPlay]

is displayed.

If the [User Account Control] dialog box is
displayed, click [Yes].

3 Select the language and then click

[Next].

7 Click the Install button on the [FAX

driver] row.

- 44 -

Faxing from a Computer (For Windows)

8 On the [Pre-Installation Check] dialog

box, click [Next].

9 Click the [Easy Installation

(Network)] button.

The device search starts.

- If the machine is detected, it is
automatically installed. Proceed to step

12.

- If the machine is not detected, the
[Review your installation settings.]
screen is displayed. Proceed to step 10.

10 Click [Restart search] to restart the

device search.

11 If the [Windows Security] dialog box

is displayed, click [Install this driver
software anyway].

12 Click the [Finish] button.

3

Faxing (For MB362, MB562, ES5462 MFP only)

13 Click [Exit] on the [Setup] window.

14 Click [Start] > [Devices and Printers].

15 Check that the OKI MC562(FAX) icon is

displayed.

If a printer driver for the machine is already
installed, the OKI MC562 icon may represent
these drivers. In this case, right-click the OKI
MC562 icon and select one of the menu items,
and then check that the fax driver is displayed in
the submenu.

After the machine is displayed, select the machine
and click [Next].

Memo

● If the machine is not displayed by clicking [Restart
search], select [Printer name/IP Address] and

enter the IP address assigned to your machine, and
then click [Next].

16 Remove the “Software DVD-ROM” from

the computer.

The installation is complete.

- 45 -

Faxing from a Computer (For Windows)

 For USB Connection

Follow the procedure below to connect a USB
cable and install a fax driver on your computer.

Note

● You must be logged in as an administrator to complete
this procedure.

Memo

● You can skip this procedure if the fax driver is already
installed on your computer.

3

1 Prepare a USB cable.

Faxing (For MB362, MB562, ES5462 MFP only)

A USB cable is not supplied with your machine.
Prepare a USB 2.0 cable separately.

Memo

● Use a USB 2.0 Hi-Speed cable for a USB 2.0 Hi­Speed connection.

2 Hold down the power switch for

approximately one second to turn off the
power.

6 Click [Run Setup.exe] after [AutoPlay]

is displayed.

If the [User Account Control] dialog box is
displayed, click [Yes].

7 Select the language and then click

[Next].

8 Select the device of your machine, and

then click [Next].

9 Read the license agreement and then

click [I Agree].

3 Plug one end of the USB cable into the

USB interface connector on the back of
the machine.

10 Read the “Environmental advice for

Users” and click [Next].

4 Turn on the computer.

5 Insert “Software DVD-ROM” into the

computer.

- 46 -

Faxing from a Computer (For Windows)

11 Click the Install button on the [FAX

driver] row.

12 On the [Pre-Installation Check] dialog

box, click [Next].

15 When the instruction to connect the

machine to the computer and turn on
the machine is displayed, plug the other
end of the USB cable into the computer’s
USB interface connector and hold down
the power switch for approximately one
second to turn on the power.

3

Faxing (For MB362, MB562, ES5462 MFP only)

13 Click [Easy Installation (Local)]

button.

14 If the [Windows Security] dialog box

is displayed, click [Install this driver
software anyway].

Note

● Do not plug the USB cable into the network interface
connection. Doing so may damage your machine.

16 Click the [Finish] button.

17 Click [Exit] on the [Setup] window.

18 Click [Start] > [Devices and Printers].

- 47 -

Faxing from a Computer (For Windows)

19 Check that the OKI MC562(FAX) icon is

displayed.

If a printer driver for the machine is already
installed, the OKI MC562 icon may represent
these drivers. In this case, right-click the OKI
MC562 icon and select one of the menu items,
and then check that the fax driver is displayed in
the submenu.

20 Remove “Software DVD-ROM” from the

3

Faxing (For MB362, MB562, ES5462 MFP only)

computer.

The installation is complete.

Procedure for Fax from a Computer

This section explains how to send fax data from
your computer.

You need to install the fax driver for your
machine on the computer before using the Fax
from Computer function.

Memo

● This section uses NotePad as example. The menu items
and procedure may differ according to the application and
the version of the fax driver you are using.

● For additional information on the setting items on the fax
driver, refer to the driver’s help.

1 Open the le you want to fax.

2 From the [File] menu, select [Print].

3 From [Select Printer], select [OKI

MC562 (FAX)] and then click [Print].

The [Settings] dialog box is displayed.

4 On the [Recipient] tab, enter the

destination name in [Name] on the
[Specifying numbers] sheet.

5 Enter the destination fax number in

[FAX number].

6 Click [Add<-].

7 Repeat steps 4 to 6 to specify all the

destinations.

8 Click the [Sender] tab, and enter the

[Sender’s name] and the [Sender’s
number].

9 Click [OK] to start transmitting.

Memo

● When you want to cancel a job while the data is
being transmitted to the machine, double-click the
printer icon in the toolbar, select the job to cancel,
and then select [Cancel] from the [Document]
menu.

Reference

● Once the data is stored in the machine, you cannot cancel
the job from your computer. For details on how to cancel a
fax job stored in the machine memory, refer to the User’s
Guide > “Faxing - MC362, MC562 AND ES5462 MFP only” >
“Sending a fax from the MFP
“Fax job view/cancel

”.

”

> “Advanced operation” >

- 48 -

4 Scanning

This chapter explains the initial setup and basic procedure for the Scan to E-mail, Scan to Network PC,
and Scan to Local PC functions.

Your machine supports the following scan functions.

Function Overview

“Scanning to E-mail” Scans documents and sends the scanned images as an attached le of an e-mail to the

specied e-mail address on the network.

“Scanning to Network
PC”

Scanning to USB
Memory

“Scanning to Local PC” Scans documents to the computer via network or USB and manipulates the scanned

Scanning to Remote PC Scans documents to the computer via network or USB and manipulates the scanned

Scans documents and saves the scanned images to the “shared folder” of a computer
on the network.

Scans documents and saves the scanned images directly to a USB memory.
For the procedure for the function, refer to the User’s Guide > “Scanning” > “Scan to
USB Memory”.

images as necessary by operating on the operator panel.

images as necessary by operating on the computer.
For the initial setup for the function, refer to the User’s Guide > “Scanning” >
“Installing Scanner Drivers (TWAIN/WIA/ICA Driver)”.
For the procedure for the function, refer to the User’s Guide > “Scanning” > “Scan to
Remote PC”.

4

Scanning

●● Scanning to E-mail

This section explains the initial setup and basic procedure for the Scan to E-mail function.

This function enables you to scan documents and send the scanned images as an attached le of an
e-mail to the specied e-mail address on the network.

Be sure to nish the initial setup before using this function.

Initial Setup for Scan to E-mail

This section explains how to congure the initial

setup for the Scan to E-mail function. Follow the
2 steps below:

● “Step 1 Conguring the Network Settings of

Your Machine” P.49

● “Step 2 Conguring the E-mail Settings of

Your Machine” P.53

Note

● You need to complete the network setting of the computer
before this procedure.

Memo

● You can skip step 1 if the IP address is already set on your
machine.

Step 1 Conguring the Network

Settings of Your Machine

Connect your machine to a network with an

Ethernet cable, and then congure the machine’s

IP address and other network information from
the operator panel. You can set the IP address
either manually or automatically.

If there is no DHCP server or BOOTP server on

the network, you need to manually congure the

IP address on the computer or machine.

If your network administrator or internet

service provider species a unique IP address

for the computer and your machine, set the IP
addresses manually.

Note

● When setting an IP address manually, ask the network
administrator or your internet service provider which IP
address to use. If the IP address is set incorrectly, the
network may go down or Internet access may be disabled.

● Conform the IP version of the machine to that of your
computer.

● Set [TCP/IP] setting to [Enable] on your machine. (By
factory default, it is set to [Enable].)

- 49 -

Scanning to E-mail

Memo

● If conguring a small network consisting of only your
machine and a computer, set IP addresses as shown
below (according to RFC1918).

For the computer

IP address : 192.168.0.1~254

Subnet mask : 255.255.255.0

Default gateway : not used

DNS server : not used

For the machine

IP Address Set : Manual

IPv4 Address : 192.168.0.1~254

Subnet Mask : 255.255.255.0

4

Scanning

Gateway Address : 0.0.0.0

Network Scale : Small

● To set [Network Scale], press the <SETTING> key
and then select [Admin Setup] > [Network Menu] >
[Network Setup] > [Network Scale].

(select a different value
from the computer)

1 Prepare an Ethernet cable and a hub.

Prepare an Ethernet cable (category 5, twisted
pair, straight) and a hub separately.

3 Plug one end of the Ethernet cable into

the network interface connection on the
back of the machine.

4 Plug the other end of the Ethernet cable

into the hub.

2 Hold down the power switch for

approximately one second to turn off the
power.

5 Hold down the power switch for

approximately one second to turn on the
power.

- 50 -

Scanning to E-mail

6 Press the <SETTING> key on the

operator panel.

7 Press the to select [Easy Setup], and

press OK.

8 Enter the administrator password.

The factory default password is “aaaaaa”.

c Press the and to select [Enter]

and press OK.

9 Press the to select [Network

Setting], and then press the .

10 If setting the IP address manually, check

that [Manual] is selected, and press OK.

4

Scanning

If obtaining the IP address automatically, press
the to select [Auto], and press OK. Proceed to
step 15.

a Press , , , to select the

character you want, and then
press OK.

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter
the correct value.

11 Enter the IP address using the ten-key

pad, and press OK.

To move to the next box, press the .

12 Enter the subnet mask using the ten-key

OK

pad, and press

To move to the next box, press the .

.

b Repeat step a until all characters

required are entered.

13 Enter the default gateway address using

the ten-key pad, and press OK.

To move to the next box, press the .

- 51 -

Scanning to E-mail

14 Enter the DNS server and WINS server if

needed.

If it is not necessary to connect the DNS server
or WINS server to the network, press
pop-up message showing setting completion is
displayed.

OK

15 When the setup menu screen is

displayed, press
setup.

to complete the

4

Scanning

16 For the conrmation message, check

that [Yes] is selected and press OK.

until the

◆ Print the Network Information to check that
the IP address and other network information
are properly set.

1 Press the <SETTING> key on the

operator panel.

2 Check that [Reports] is selected and

OK

press

.

3 Press the to select [System] and

press OK.

4 Press the to select [Network

Information] and press OK.

5 For the conrmation message, check

OK

that [Yes] is selected and press

The Network Information is printed.

.

- 52 -

Step 2 Conguring the E-mail Settings of Your Machine

To congure the E-mail Settings of your machine, follow the 3 sub steps below:

● “Step 2-1 Checking the E-mail Settings of the Computer” P.53

● “Step 2-2 Setting the E-mail Address for Your Machine” P.54

● “Step 2-3 Conguring Your Machine’s E-mail Settings” P.54

Check the values for each item in the Setup Information Form through the above steps.

 Setup Information Form

User Value

No. Item Outline Introduction Example

B-1 E-mail address for

your machine

B-2 SMTP server address The address of the server used

B-3 POP3 server address The address of the server used

B-4 Authentication

method
B-5 SMTP user ID Sending mail server account name OKIMC562
B-6 SMTP password Sending mail server password okimc562
B-7 POP user ID Receiving mail server account name user
B-8 POP password Receiving mail server password okimc562
B-9 Name of the e-mail

destination

B-10

E-mail address of the

e-mail destination

The e-mail address used when
sending e-mails from the machine

when sending e-mails

when receiving e-mails
Sending mail server authentication SMTP

The name of the recipient to whom
you are sending a scan-to-mail from
the machine

The e-mail address of the recipient
to whom you are sending a scan-to­mail from the machine

mc362@test.
com

smtp.test.com

pop3.test.com

User

[e-mail]

* You can look at the following pages

and make notes on the details you
have checked or the settings you

have congured.

(Up to 80 characters)

Scanning to E-mail

4

Scanning

 Step 2-1 Checking the E-mail

Settings of the Computer

Note

● If a network administrator species values such as mail
server account, password and e-mail address for your
machine, enter them in the Setup Information Form.

Memo

● The procedure below uses Windows Live Mail on Windows

7. If you are using different mail software, refer to the
manual for the e-mail software.

1 Click [Start] and select [Windows Live

Mail].

2 Select the [Tools] menu > [Accounts].

If the menu bar is not displayed, click the
[Menus] icon and then select [Show menu
bar].

3 Select the mail account and then click

[Properties].

- 53 -

Scanning to E-mail

4 On the [General] tab, enter the

contents of [Name] and [E-mail
address] in B-9 and B-10 of the Setup

Information Form.

4

Scanning

5 Click the [Servers] tab, and then

note each setting in the corresponding
columns of the Setup Information Form.

B-9

B-10

B-3
B-2

B-7
B-8

7 Check the login information on the

[Outgoing Mail Server] dialog box.

- If [Use same settings as my incoming
mail server] is selected, enter the same
values as B-7 and B-8 on B-5 and B-6.

- If [Log on using] is selected, note
the content of [Account name] and
[Password] in B-5 and B-6, respectively.

 Step 2-2 Setting the E-mail

Address for Your Machine

When sending data scanned from the
machine by an e-mail, the e-mail address for
the machine is necessary. According to the
following procedure, set the e-mail address for
the machine and enter it in B-1 of the Setup
Information Form.

● If the e-mail address for your machine is

specied by the network administrator, enter

the e-mail address in B-1.

● If you are using an internet service provider,
obtain an e-mail address for your machine
from the provider and then enter the e-mail
address in B-1.

- If there is a check in the [My server
requires authentication] checkbox,
enter “SMTP” into B-4 and follow
procedure 6.

- If there is no check in the [My server
requires authentication] checkbox,
enter [POP or not yet authenticated]

in B-4. At this point the conrmation of

e-mail settings is complete.

Note

● If using an internet service provider, enter [POP].

6 Click [Settings].

● If the e-mail address for your machine is
neither specied nor obtained, determine the

e-mail address according to the value you
entered in B-4 (authentication method):

- If B-4 is “SMTP”, determine an e-mail
address and enter it in B-1.

- If B-4 is “POP”, enter the same e-mail
address as B-10 in B-1.

Note

● If you want your machine to receive e-mail, you must
obtain an e-mail address for your machine from a network
administrator or your internet service provider.

 Step 2-3 Conguring Your

Machine’s E-mail Settings

Set up your machine’s e-mail settings using the
information in the Setup Information Form.

- 54 -

Scanning to E-mail

1 Press the <SETTING> key on the

operator panel.

2 Press the to select [Easy Setup] and

press OK.

3 Enter the administrator password.

The factory default password is “aaaaaa”.

a Press , , , to select the

character you want, and then
press OK.

c Press the and to select [Enter]

and press

OK

.

4 Press the to select [E-mail Setting]

and then press the .

5 Press the and then enter the

information in B-2.

6 Select [Enter] and then press

OK

.

7 Press the and then enter the

information in B-1.

8 Select [Enter] and then press

OK

.

9 Press the and then select a protocol

for receiving e-mail for the machine, and
then press OK.

- If you want your machine to receive
e-mail from the POP3 server, select
[POP3]. Proceed to step 10.

4

Scanning

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter
the correct value.

- If you want your machine to receive
e-mail without using a mail server, select
[SMTP]. Proceed to step 12.

- If you do not want your machine to
receive e-mail, select [Disable]. Proceed
to step 12.

10 Press the and then enter the

information in B-3.

11 Select [Enter] and then press

12 Press the and then select an

authentication method based on the
information in B-4. Then, press OK.

- If B-4 is “Do not authenticate”, select [No
Authentication]. Proceed to step 21.

- If B-4 is “SMTP”, select [SMTP Auth].
Proceed to step 13.

- If B-4 is “POP”, select [POP Before
SMTP]. Proceed to step 17.

OK

.

b Repeat step a until all characters

required are entered.

- 55 -

13 Press the and then enter the

information in B-5.

14 Select [Enter] and then press

OK

.

Scanning to E-mail

15 Press the and then enter the

information in B-6.

16 Select [Enter] and then press

Proceed to step 21.

17 Press the and then enter the

information in B-7.

18 Select [Enter] and then press

19 Press the and then enter the

information in B-8.

20 Select [Enter] and then press

4

21 When the setup menu screen is

Scanning

displayed, press .

Procedure of Scan to E-mail

OK

.

OK

.

OK

.

This section explains how to start Scan to
E-mail. The following procedure uses the direct
input method for specifying a destination.

You need to congure the initial network and

e-mail settings before using the Scan to E-mail
function.

Memo

● The following procedure uses the factory default settings.

1 Press the <SCAN> key on the operator

panel.

22 For the conrmation message, check

that [Yes] is selected and press OK.

The setup for Scan to E-mail is complete.

2 Place your document in the ADF or on

the document glass as below:

● ADF

Load documents face up with the top edge of the

documents in rst.

Adjust the document guides to the width of your
documents.

- 56 -

Scanning to E-mail

● Document Glass

Place a document face down and align its top
edge to the upper-left corner of the glass.

Close the document glass cover gently.

Note

● Do not apply an excessive load to the document
glass.

7 Enter a destination e-mail address up to

80 characters.

a Press , , , to select the

character you want, and then
press OK.

The selected character is entered in the text

eld.

4

Scanning

Memo

● The machine prioritizes the ADF when scanning
documents. Be sure not to place documents on the
ADF when you use the document glass.

Note

● If Carriage Error <02> is displayed, press Power
OFF/ON.

3 Check that [E-mail] is selected and then

press OK.

4 Check that [Add Destination] is

selected and then press OK.

If you have entered an incorrect value, press
the <CLEAR> key and then enter the correct
value.

b Repeat step a until all characters

required are entered.

c Press the and to select [Enter]

and press OK.

8 If necessary, select [Cc] or [Bcc] and

repeat steps 6 and 7.

9 Press the to return to start screen.

10 Press

Reference

● In addition to inputting the destination directly, you can
use the address book, group list, e-mail histories, LDAP
search, or One-Touch key pad to specify the destination.
For details, refer to the User’s Guide > “Scanning” >
“Scan to E-mail”.

● To load a landscape document, refer to the User’s Guide >
“Operation” > “Loading document(s)”.

MONO

or

COLOR

.

5 Check that [To] is selected and then

press OK.

6 Press the to select [Direct Input] and

then press OK.

- 57 -

Scanning to Network PC

●● Scanning to Network PC

This section explains the initial setup and basic procedure for the Scan to Network PC function.

This function enables you to scan documents and save the scanned images to the “shared folder” of a
computer on the network.

Be sure to nish the initial setup before using this function.

Initial Setup for Scan to Network PC

This section explains how to congure the initial

setup for the Scan to Network PC function.
Follow the 2 steps below:

4

● “Step 1 Conguring the Network Settings of

Scanning

Your Machine” P.58

● “Step 2 Setting Up Your Computer and

Machine for Scan to Network PC” P.61

Note

● You need to congure the network setting of the computer
before this procedure.

Memo

● You can skip step 1 if the IP address is already set on your
machine.

Step 1 Conguring the Network

Settings of Your Machine

Connect your machine to a network with an

Ethernet cable, and then congure the machine’s

IP address and other network information from
the operator panel. You can set the IP address
either manually or automatically.

Memo

● If conguring a small network consisting of only your
machine and a computer, set IP addresses as shown
below (according to RFC1918).

For the computer

IP address : 192.168.0.1~254

Subnet mask : 255.255.255.0

Default gateway : not used

DNS server : not used

For the machine

IP Address Set : Manual

IPv4 Address : 192.168.0.1~254

(select a different value
from the computer)

Subnet Mask : 255.255.255.0

Gateway Address : 0.0.0.0

Network Scale : Small

● To set [Network Scale], press the <SETTING> key
and then select [Admin Setup] > [Network Menu] >
[Network Setup] > [Network Scale].

1 Prepare an Ethernet cable and a hub.

Prepare an Ethernet cable (category 5, twisted
pair, straight) and a hub separately.

If there is no DHCP server or BOOTP server on

the network, you need to manually congure the

IP address on the computer or machine.

If your network administrator or internet

service provider species a unique IP address

for the computer and your machine, set the IP
addresses manually.

Note

● When setting an IP address manually, ask the network
administrator or your internet service provider which IP
address to use. If the IP address is set incorrectly, the
network may go down or Internet access may be disabled.

● Conform the IP version of the machine to that of your
computer.

● Set [TCP/IP] setting to [Enable] on your machine. (By
factory default, it is set to [Enable].)

2 Hold down the power switch for

approximately one second to turn off the
power.

- 58 -

Scanning to Network PC

3 Plug one end of the Ethernet cable into

the network interface connection on the
back of the machine.

4 Plug the other end of the Ethernet cable

into the hub.

6 Press the <SETTING> key on the

operator panel.

7 Press the to select [Easy Setup], and

press OK.

4

Scanning

8 Enter the administrator password.

The factory default password is “aaaaaa”.

5 Hold down the power switch for

approximately one second to turn on the
power.

a Press , , , to select the

character you want, and then
press OK.

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter
the correct value.

- 59 -

b Repeat step a until all characters

required are entered.

Scanning to Network PC

c Press the and to select [Enter]

and press OK.

9 Press the to select [Network

Setting], and then press the .

10 If setting the IP address manually, check

that [Manual] is selected, and press OK.

4

Scanning

If obtaining the IP address automatically, press
the to select [Auto], and press OK. Proceed to
step 15.

11 Enter the IP address using the ten-key

pad, and press OK.

14 Enter the DNS server and WINS server if

needed.

If it is not necessary to connect the DNS server
or WINS server to the network, press
pop-up message showing setting completion is
displayed.

OK

until the

15 When the setup menu screen is

displayed, press
setup.

to complete the

16 For the conrmation message, check

that [Yes] is selected and press OK.

◆ Print the Network Information to check that
the IP address and other network information
are properly set.

1 Press the <SETTING> key on the

operator panel.

To move to the next box, press the .

12 Enter the subnet mask using the ten-key

OK

pad, and press

To move to the next box, press the .

.

13 Enter the default gateway address using

the ten-key pad, and press OK.

To move to the next box, press the .

2 Check that [Reports] is selected and

press OK.

3 Press the to select [System] and

press OK.

4 Press the to select [Network

Information] and press OK.

5 For the conrmation message, check

that [Yes] is selected and press OK.

The Network Information is printed.

- 60 -

Scanning to Network PC

Step 2 Setting Up Your Computer and Machine for Scan to Network PC

To setup your computer and machine for Scan to Network PC, follow the 4 sub steps below:

● “Step 2-1 Checking the Name of the Computer” P.61

● “Step 2-2 Determining the Names of the Items Required for Scan to Network PC” P.62

● “Step 2-3 Conguring the Computer for Scan to Network PC” P.63

● “Step 2-4 Creating a Prole for Scan to Network PC” P.70

Check the values for each item in the Setup Information Form through the above steps.

 Setup Information Form

User Value

No. Item Outline Introduction Example

C-1 Name of the

destination computer

C-2 User name to log

into the destination
computer

C-3 Password to log

into the destination
computer

C-4 Prole name to

register the settings

C-5 Shared folder name

on the destination
computer

C-6 File name of the

scanned data

The name of the computer to which
you are forwarding scanned data

User name to log in to the computer
to which you are forwarding scanned
data

Password to log in to the computer
to which you are forwarding scanned
data

Name when registering a prole on

the machine
Folder name of the computer to

which you are forwarding scanned
data

Scanned data le name ScanData (Up to 64 characters)

PC1

mc562 (Up to 32 characters)

mc562 (Up to 32 characters)

Sales (Up to 16 characters)

SalesDev (Up to 64 characters)

* You can look at the following pages

and make notes on the details you
have checked or the settings you

have congured.

4

Scanning

Note

● Before starting the setup, obtain permission from the network administrator to create a shared folder on the computer by
following the procedure below.

Memo

● The CIFS protocol is used in this procedure.

 Step 2-1 Checking the Name of

the Computer

Check the name of the computer following the

procedure below, and ll in C-1 of the Setup

Information Form.

3 Select [See the name of this

computer] under [System].

4 Enter the name in [Computer name] in

C-1 of the Setup Information Form.

 For Windows 7, Windows Server

2008 R2, Windows Server 2008 and

Windows Vista

1 Click [Start] and select [Control

Panel].

2 Select [System and Security].

For Windows Server 2008 and Windows Vista,
select [System and Maintenance].

5 Close the window.

C-1

- 61 -

Scanning to Network PC

 For Windows Server 2003 and

Windows XP

1 Click [start] > [Control Panel] >

[Performance and Maintenance] >
[System].

For Windows Server 2003, click [Start] >
[Operator panel] > [System].

2 Select the [Computer Name] tab and

then click [Change].

3 Enter the name in [Computer Name] in

C-1 of the Setup Information Form.

4

4 Click [Cancel] to close the window.

Scanning

 For Mac OS X

1 From the Apple menu, select [System

Preferences].

2 Click [Sharing].

3 Enter the name in [Computer Name] in

C-1 of the Setup Information Form.

 Step 2-2 Determining the Names

of the Items Required for Scan to
Network PC

Determine the names of the following items and

ll in C-2 to C-6 on the Setup Information Form.

● User name to log into the destination computer (C-2)

Note

● If the username is managed on the domain,
enter “Username@Domainname” in C-2. To check
the domain name, click on [Change] within the
[Computer Name] tab in the [System Properties]
dialog box.

● Password to log into the destination computer
(C-3)

● Prole name to register the settings on your
machine (C-4)

● Shared folder name on the destination
computer (C-5)

● File name of the scanned data (C-6)

“#n” or #d” can be specied for the le name.

- When specifying “#n”: 5-digit serial
number between 00000 to 99999

- When specifying “#d”: Date and time

when a le is created. 12 digits of

yymmddhhmmss.

Memo

● If the computer name is over 16 characters, for
Mac OS X 10.4.11 enter the rst 15 characters in

C-1. For Mac OS X 10.5-10.7, select the network
service you are using from [System Preferences] >
[Network], and click [Advanced]. Click the [WINS]
tab, and enter the name in [NetBIOS Name] into
C-1.

4 Close [Sharing].

C-1

yy: Year created (the last 2 digits of the

Christian Era)
mm: Month created (01 to 12)
dd: Date created (01 to 31)
hh: Hours created (00 to 23)
mm: Minute created (00 to 59)
ss: Second created (00 to 59)

* A date and time when a le is created are values of the

timer of the machine.

Example of le name specication (when the le

format is PDF)

- When specifying “Data#n”: Saved as

le names such as “Data00000.pdf” and

“Data00001.pdf”,etc.

- When specifying “File#d”: saved as le
names “File090715185045.pdf”, etc.

- When specifying “Scan”: “Scan.pdf” is

created rst, and then, data is saved with

the name of ”Scan#d.pdf”.
For “#d”, refer to the above.

- When nothing is specied: “Image.pdf” is

created rst and then, data is saved with

the name of “Image#d.pdf”.
For “#d”, refer to the above.

- 62 -

Scanning to Network PC

 Step 2-3 Conguring the

Computer for Scan to Network PC

With the Setup Information Form, create an
account and shared folder for the machine in the
computer.

Memo

● If the computer is in a domain, the procedure for adding a
user account may differ from the procedure below. Refer
to the Microsoft Windows manual.

 For Windows 7, Windows Server 2008

R2, Windows 2008 and Windows

Vista

1 Click [Start] > [Control Panel].

2 Select [Add or remove user

accounts].

3 Select [Create a new account].

4 Enter the information in C-2 in the text

box.

8 Enter the information in C-3 in [New

password] and [Conrm new
password], and then click [Create
password].

4

Scanning

9 Close the Control Panel.

10 Create a new folder on the computer

with the name entered in C-5.

Memo

● It is recommended that the folder be created in the
local drive (C drive or D drive), not on the desktop,
[Documents], or network drive.

5 Ensure that [Standard user] is

selected, and then click [Create
Account].

6 Click the icon of the user account

created in step 5.

7 Select [Create a password].

11 Right-click the folder created in step 10

and select [Properties].

12 Select the [Sharing] tab and then click

[Share].

- 63 -

Scanning to Network PC

13 Select the user account created in step 5

from the drop down box, and then click
[Add].

4

14 Check that the user added in step 13 is

Scanning

displayed and then click [Share].

18 Click [Add].

19 Enter the value in C-2 in the entry eld

and then click [OK].

After the [Network discovery and le sharing]
dialog box is displayed, click [No, make the

network that I am connected to a private
network].

15 Click [Done].

16 Click [Advanced Sharing] on the

[Sharing] tab.

17 Click [Permissions].

20 Select the user added in step 13 and

select the [Allow] checkbox for [Full
Control], and then click [OK].

21 Click [OK].

22 Click [Close].

Proceed to “Step 2-4 Creating a Prole for Scan

to Network PC” P.70.

 For Windows XP

For Windows Vista/Windows Server 2008,
proceed to the step 20.

1 Click [start] > [Control Panel].

2 Double-click [User Accounts].

3 Select [Create a new account].

- 64 -

Scanning to Network PC

4 Enter the value of C-2 in the text box

and click [Next].

5 Select [Limited] and click [Create

Account].

11 Right-click the folder created in step

10, and then select [Sharing and
Security].

12 Click [If you understand the security

risks but want to share les without

running the wizard, click here.].

4

Scanning

If the screen below is displayed, select [Share
this folder] and click [Permissions]. Proceed to
step 15.

6 Click the icon of the user account

created in step 5.

7 Select [Create a password].

8 Enter the value of C-3 in [Type a

new password] and [Type the new

password again to conrm], and then
click [Create Password].

13 Select [Just enable le sharing] in

Windows Firewall, and then click [OK].

9 Close the Control Panel.

10 Create a new folder on the computer

with the name entered in C-5.

Memo

● It is recommended that the folder be created in the
local drive (C drive or D drive), not on the desktop,
[My Documents], or network drive.

- 65 -

Scanning to Network PC

14 Select the [Share this folder on the

network] and [Allow network users

to change my les] checkbox, and
then click [OK].

4

Proceed to “Step 2-4 Creating a Prole for Scan

Scanning

to Network PC” P.70.

15 Click [Add].

17 Select the [Allow] checkbox for [Full

Control], and then click [OK].

Proceed to “Step 2-4 Creating a Prole for Scan

to Network PC” P.70.

 For Windows Server 2003

Memo

● The items here may differ depending on the edition you
are using.

1

Click [Start] > [Administrative Tools] >
[Computer Management].

16 Enter the value in C-2 in the entry eld

and click [OK].

2 In the right window, double-click

[System Tools] > [Local Users and
Groups], and then right-click [Users]
and select [New User].

3 Enter the value of C-2 in [User name]

and the value of C-3 in [Password] and
[Conrm password].

- 66 -

Scanning to Network PC

4 Select [User can not change

password] and [Password never
expires], and then click [Create].

Memo

● If [User must change password at next logon]
is selected, deselect so that you can select [User

can not change password] and [Password never
expires].

5 Click [Close].

6 Double-click [User] and check that the

user created in step 4 is displayed.

7 Close the window.

8 Create a new folder on the computer

with the name entered in C-5.

Memo

● It is recommended that the folder be created in the
local drive (C drive or D drive), not on the desktop,
[My Documents], or network drive.

9 Right-click the folder created in step 8

and then select [Sharing].

10 Select [Share this folder] and then

click [Permissions].

12 Enter the value in C-2 in the entry eld

and click [OK].

13 Select the [Allow] checkbox for [Full

Control], and then click [OK].

4

Scanning

14 Ensure that the icon of the shared folder

created in step 8 changes into the icon
with a hand, and then close the window.

Proceed to “Step 2-4 Creating a Prole for Scan

to Network PC” P.70.

11 Click [Add].

 For Mac OS X 10.5 to 10.7

1 From the Apple menu, select [System

Preferences].

2 Click [Users & Groups] (for Mac OS X

10.5 and 10.6: [Accounts]).

3 Click [Click the lock to make

changes.] at the bottom left of the

screen and enter the administrator’s
password. Then, click [Unlock] (for Mac
OS X 10.5 and 10.6: [OK]).

4 Click [+].

- 67 -

Scanning to Network PC

5 Select [Standard] from [New

Account].

6 Enter the value of C-2 in [Full Name].

For Mac OS X 10.5, enter the value of C-2 in
[Name].

4

7 Enter the value in C-3 in both

Scanning

[Password] and [Verify].

8 Click [Create User] (for Mac OS X 10.5

and 10.6: [Create Account]).

Memo

● After the dialog box for auto login, disable the auto
login.

13 Select the checkbox for [File Sharing].

14 Click [+] under [Shared Folders].

15 Select the folder created in step 10 and

click [Add].

16 Select the folder added in step 15 and

click [+] under [Users].

9 Check that an account is added to

[Other Users] (for Mac OS X 10.5 and

10.6: [Other Accounts]) with the name
of C-2, and close [Users & Groups] (for
Mac OS X 10.5 and 10.6: [Accounts]) .

10 Create a new folder on the computer

with the name entered in C-5.

11 From the Apple menu, select [System

Preferences].

17 Select the account created in step 8 and

click [Select].

12 Click [Sharing].

- 68 -

Scanning to Network PC

18 Click the triangle button at the right side

of the user added in step 17 and select
[Read & Write].

19 Click [Options].

20 Select the checkbox for [Share les

and folders using SMB (Windows)].

For Mac OS X 10.5, select the checkbox for
[Share les and folders using SMB].

 For Mac OS X 10.3.9 to 10.4.11

Memo

● The following procedure uses Mac OS X 10.4.11 as an
example. The description may differ depending on the OS.

1 From the Apple menu, select [System

Preferences].

2 Click [Accounts].

3 Click [Click the lock to make

changes.] at the bottom left of the
screen and enter the administrator’s
password. Then, click [OK].

4 Click [+].

4

Scanning

21 Select the checkbox for the account

added in the step 16.

22 Enter the value of C-3 in [Password]

and click [OK].

23 Click [Done].

24 Close [Sharing].

Proceed to “Step 2-4 Creating a Prole for Scan

to Network PC” P.70.

5 Enter the value of C-2 in [Name].

6 Enter the value in C-3 in both

[Password] and [Verify].

7 Click [Create Account].

Memo

● After the dialog box for auto login, disable the auto
login.

- 69 -

Scanning to Network PC

8 Check that an account is added to

[Other Accounts] with the name of
C-2, and close [Accounts].

4

Scanning

9 Create a new folder on the computer

with the name entered in C-5.

10 From the Apple menu, select [System

Preferences].

15 Enter the value in C-3 in [Password]

and click [OK].

16 Click [Done].

17 Close [Sharing].

Proceed to “Step 2-4 Creating a Prole for Scan

to Network PC” P.70.

 Step 2-4 Creating a Prole for

Scan to Network PC

Register the information on the Setup

Information Form on the machine as a prole. It
is necessary to specify the prole to send data

when you perform Scan to Network PC with the
computer.

11 Click [Sharing].

12 Select the checkbox of [Windows

Sharing].

13 Click [Accounts...].

14 Select the checkbox for the account

created in the step 7.

1 Press the <SETTING> key on the

operator panel.

2 Press the to select [Prole] and then

press OK.

3 Press the to select the prole number

you want to register and then press OK.

- 70 -

4 Check that [Register] is selected and

then press

OK

.

5 Check that [Prole Name] is selected

and then press the .

6 Enter the information in C-4.

Scanning to Network PC

a Press , , , to select the

character you want, and then
press

- The selected character is entered in the

text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter
the correct value.

OK

.

11 Enter the information in C-2.

Note

● If domain management is done, enter “C-2@domain
name”.

● When carrying out domain management, if
you cannot connect even after entering “C-2@
Domainname”, delete “@Domainname”.
Access the machine’s website again, and set the
NetBIOS domain name in [Workgroup Name]
within [Admin Setup] > [Network] > [NBT/
NetBEUI].
*For the domain name, please check with the
network manager.

12 Select [Enter] and then press

OK

.

13 Press the to select [Password] and

then press .

14 Enter the value of C-3.

15 Select [Enter] and then press

OK

.

16 Press the to select [File Name] and

then press .

4

Scanning

b Repeat step a until all characters

required are entered.

c Press the and to select [Enter]

and press OK.

7 Press the to select [Target URL] and

then press .

8 Enter the value of C-1 and C-5 as

“\\C- 1\C-5”.

Example: \\PC1\SalesDev

Note

● If there is no DNS server on the network, you cannot
specify the computer by using the computer name

(C-1). In such a case, you can congure the settings

by using the computer’s IP address.

17 Enter the information in C-6.

18 Select [Enter] and then press

OK

.

19 Congure other items if necessary.

20 Press

The setup for Scan to Network PC is complete.

OK

to register the settings.

Example: \\192.168.0.3\SalesDev

Memo

● In order to enter the “\” sign while using a QWERTY
keyboard, press <CTRL> and then press <\>.

9 Select [Enter] and then press

OK

.

10 Press the to select [User Name] and

then press .

- 71 -

Scanning to Network PC

Procedure for Scan to Network PC

This section explains how to start Scan to
Network PC.

You need to congure the initial settings before

using the Scan to Network PC function.

Memo

● The following procedure uses the factory default settings.

1 Press the <SCAN> key on the operator

panel.

4

Scanning

Note

● Do not apply an excessive load to the document
glass.

Memo

● The machine prioritizes the ADF when scanning
documents. Be sure not to place documents on the
ADF when you use the document glass.

Note

● If Carriage Error <02> is displayed, press Power
OFF/ON.

3 Press the to select [Network PC] and

then press OK.

2 Place your document in the ADF or on

the document glass as below:

● ADF

Load documents face up with the top edge of the

documents in rst.

Adjust the document guides to the width of your
documents.

● Document Glass

Place the document face down and align its top
edge to the upper-left corner of the glass.

4 Check that [Select Prole] is selected

and then press OK.

5 Press the to select a prole and then

press OK.

6 Press

Reference

● To load a landscape document, refer to the User’s Guide >
“Operation” > “Loading document(s)”.

MONO

or

COLOR

.

Close the document glass cover gently.

- 72 -

Scanning to Local PC

●● Scanning to Local PC

This section explains the initial setup and basic procedure for the Scan to Local PC function.

This function enables you to scan documents to the computer via network or USB, and manipulate the
scanned images as necessary. You can start a scan job from the operator panel.

● For Windows

When you press the

the scanner driver. You can send the scanned document to a specied application, save it in a specied

folder, or send it by fax.

For the WSD Scan connection, you can specify the application to start and where to send and save the
scanned document for each destination.

● For Mac OS X

When you press the
the ICA driver. You can select a folder and save the scanned documents in it.

The machine can be connected to USB interface or network, but only a computer can be recognized at
the same time.

Be sure to nish the initial setup before using this function.

or

MONO

or

MONO

, the ActKey utility starts, and the scan job starts automatically using

COLOR

, Image Capture starts, and the scan job starts automatically using

COLOR

4

Scanning

Initial Setup for Scan to Local PC

This section explains how to congure the initial

setup for the Scan to Local PC function.

Refer to the procedure for the OS you are using.

● “For Windows” P.73

● “For Mac OS X” P.84

For Windows

 Overview

 Connecting Methods

You can select one of the following connection
methods:

● “For Network Connection” P.74

● “For USB Connection” P.78

● “For WSD Scan Connection” P.80

 Product Requirements

Your machine supports the following Windows
operating systems.

For Network/USB Connection:

● Windows 7/Windows 7 (64bit Version)

● Windows Vista/Windows Vista (64bit Version)

● Windows Server 2008 R2

● Windows Server 2008/Windows Server 2008
(x64 Version)

● Windows XP/Windows XP (x64 Version)

● Windows Server 2003/Windows Server 2003
(x64 Version)

For WSD Scan Connection:

● Windows 7/Windows 7 (64bit Version)

● Windows Vista/Windows Vista (64bit Version)

● Windows Server 2008 R2

● Windows Server 2008/Windows Server 2008
(x64 Version)

- 73 -

Scanning to Local PC

 For Network Connection

To congure the Scan to Local PC function via

the network connection, follow the 2 steps
below:

● “Step 1 Conguring the Network Settings of

Your Machine” P.74

● “Step 2 Installing Driver and Software” P.77

Note

● You need to congure the network setting of the computer
before this procedure.

Memo

● You can skip step 1 if the IP address is already set on your
machine.

● You can skip step 2 if the scanner driver and ActKey are

4

Scanning

already installed on your computer.

 Step 1 Conguring the Network

Settings of Your Machine

Connect your machine to a network with an

Ethernet cable, and then congure the machine’s

IP address and other network information from
the operator panel. You can set the IP address
either manually or automatically.

Memo

● If conguring a small network consisting of only your
machine and a computer, set IP addresses as shown
below (according to RFC1918).

For the computer

IP address : 192.168.0.1~254

Subnet mask : 255.255.255.0

Default gateway : not used

DNS server : not used

For the machine

IP Address Set : Manual

IPv4 Address : 192.168.0.1~254

(select a different value
from the computer)

Subnet Mask : 255.255.255.0

Gateway Address : 0.0.0.0

Network Scale : Small

● To set [Network Scale], press the <SETTING> key
and then select [Admin Setup] > [Network Menu] >
[Network Setup] > [Network Scale].

1 Prepare an Ethernet cable and a hub.

Prepare an Ethernet cable (category 5, twisted
pair, straight) and a hub separately.

If there is no DHCP server or BOOTP server on

the network, you need to manually congure the

IP address on the computer or machine.

If your network administrator or internet

service provider species a unique IP address

for the computer and your machine, set the IP
addresses manually.

Note

● When setting an IP address manually, ask the network
administrator or your internet service provider which IP
address to use. If the IP address is set incorrectly, the
network may go down or Internet access may be disabled.

● To congure the Scan to Local PC function via the network
connection, follow these instructions.

- Conform the IP version of the machine to that of your
computer.

- Set [TCP/IP] setting to [Enable] on your machine.
(By factory default, it is set to [Enable].)

- Set [Network TWAIN] setting to [ON] on your
machine. (By factory default, it is set to [ON]. If
it has been disabled, enable it by referring to the

Conguration Guide > “Conguring the scanning

to Local and Remote PCs” > “Using Functions for
Scanning to Local and Remote PCs” > “Enabling the
Network TWAIN Setting”.)

2 Hold down the power switch for

approximately one second to turn off the
power.

- 74 -

Scanning to Local PC

3 Plug one end of the Ethernet cable into

the network interface connection on the
back of the machine.

4 Plug the other end of the Ethernet cable

into the hub.

6 Press the <SETTING> key on the

operator panel.

7 Press the to select [Easy Setup], and

press OK.

4

Scanning

8 Enter the administrator password.

The factory default password is “aaaaaa”.

5 Hold down the power switch for

approximately one second to turn on the
power.

a Press , , , to select the

character you want, and then
press OK.

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter
the correct value.

- 75 -

b Repeat step a until all characters

required are entered.

Scanning to Local PC

c Press the and to select [Enter]

and press OK.

9 Press the to select [Network

Setting], and then press the .

10 If setting the IP address manually, check

that [Manual] is selected, and press OK.

4

Scanning

If obtaining the IP address automatically, press
the to select [Auto], and press OK. Proceed to
the step 15.

11 Enter the IP address using the ten-key

pad, and press OK.

14 Enter the DNS server and WINS server if

needed.

If it is not necessary to connect the DNS server
or WINS server to the network, press
pop-up message showing setting completion is
displayed.

OK

until the

15 When the setup menu screen is

displayed, press
setup.

to complete the

16 For the conrmation message, check

that [Yes] is selected and press OK.

◆ Print the Network Information to check that
the IP address and other network information
are properly set.

1 Press the <SETTING> key on the

operator panel.

To move to the next box, press the .

12 Enter the subnet mask using the ten-key

OK

pad, and press

To move to the next box, press the .

.

13 Enter the default gateway address using

the ten-key pad, and press OK.

To move to the next box, press the .

2 Check that [Reports] is selected and

press OK.

3 Press the to select [System] and

press OK.

4 Press the to select [Network

Information] and press OK.

5 For the conrmation message, check

that [Yes] is selected and press OK.

The Network Information is printed.

- 76 -

Scanning to Local PC

 Step 2 Installing Driver and Software

The following procedure installs a scanner driver
and ActKey at once.

1 Check that your machine and the

computer are turned on and connected,
and then insert the”Software DVD-ROM”
into the computer.

2 Click [Run Setup.exe] after [AutoPlay]

is displayed.

If the [User Account Control] dialog box is
displayed, click [Yes].

3 Select the language and then click

[Next].

4 Select the device of your machine, and

then click [Next].

7 Check that [Scanner driver] and

[ActKey] are selected, and then click
the Install bunch button.

Memo

● By default, [PCL driver], [Scanner driver], and
[ActKey] are selected. Deselect [PCL driver] if it is
unnecessary or has been installed on the computer
already.

4

Scanning

8 If the [Windows Security] dialog box

is displayed, click [Install this driver
software anyway].

5 Read the license agreement and then

click [I Agree].

6 Read “Environmental advice for Users”

and click [Next].

9 Click the [Network] button.

The device search starts.

- If the machine is detected, it is
automatically installed. Proceed to step

11.

- If the machine is not detected, the
[Review your installation settings.]
screen is displayed. Proceed to step 10.

- 77 -

Scanning to Local PC

10 Click [Restart search] to restart the

device search.

After the machine is displayed, select the machine
and click [Next].

4

Scanning

Memo

● If the machine is not displayed by clicking [Restart
search], select [Printer name/IP Address] and

enter the IP address assigned to your machine, and
then click [Next].

13 Remove the “Software DVD-ROM” from

the computer.

The installation is complete.

Reference

● When installing ActKey, Network Conguration is
also installed simultaneously. Network Conguration
automatically acquires the IP address of your machine

and network information (IP address, computer name,
port number) of the computer. If the IP address or other
settings of the machine or computer is changed, you
need to change the settings. For details, refer to the

Conguration Guide > “Conguring the scanning to Local

and Remote PCs” > “Using Drivers and Software” >

“Using ActKey Software” > “Using Network Conguration”.

 For USB Connection

To congure the Scan to Local PC function via

the USB connection, install a scanner driver and
ActKey on the computer.

Memo

● You can skip this procedure if the scanner driver and
ActKey are already installed on your computer.

1 Prepare a USB cable.

A USB cable is not supplied with your machine.
Prepare a USB 2.0 cable separately.

11 If the [Windows Security] dialog box

is displayed, click [Install this driver
software anyway].

12 Click the [Exit] button.

Memo

● Use a USB 2.0 Hi-Speed cable for a USB 2.0 Hi-
Speed connection.

2 Hold down the power switch for

approximately one second to turn off the
power.

- 78 -

Scanning to Local PC

3 Plug one end of the USB cable into the

USB interface connector on the back of
the machine.

4 Turn on the computer.

5 Insert “Software DVD-ROM” into the

computer.

6 Click [Run Setup.exe] after [AutoPlay]

is displayed.

If the [User Account Control] dialog box is
displayed, click [Yes].

10 Read the “Environmental advice for

Users” and click [Next].

11 Check that [Scanner driver] and

[ActKey] are selected, and then click
the Install bunch button.

Memo

● By default, [PCL driver], [Scanner driver], and
[ActKey] are selected. Deselect [PCL driver] if it is
unnecessary or has been installed on the computer
already.

4

Scanning

7 Select the language and then click

[Next].

8 Select the device of your machine, and

then click [Next].

9 Read the license agreement and then

click [I Agree].

12 If the [Windows Security] dialog box

is displayed, click [Install this driver
software anyway].

- 79 -

Scanning to Local PC

13 When the instruction to connect the

machine to the computer and turn on
the machine is displayed, plug the other
end of the USB cable into the computer’s
USB interface connector and hold down
the power switch for approximately one
second to turn on the power.

4

Scanning

 For WSD Scan Connection

To congure the Scan to Local PC via the WSD

Scan connection, follow the 2 steps below:

● “Step 1 Conguring the Network Settings of

Your Machine” P.80

● “Step 2 Installing Your Machine to the

Computer” P.83

Note

● You need to congure the network setting of the computer
before this procedure.

Memo

● You can skip the step 1 if the IP address is already set on
your machine.

 Step 1 Conguring the Network

Settings of Your Machine

Connect your machine to a network with an

Ethernet cable, and then congure the machine’s

IP address and other network information from
the operator panel. You can set the IP address
either manually or automatically.

Note

● Do not plug the USB cable into the network interface
connection. Doing so may damage your machine.

14 Click the [Exit] button.

If there is no DHCP server or BOOTP server on

the network, you need to manually congure the

IP address on the computer or machine.

If your network administrator or internet

service provider species a unique IP address

for the computer and your machine, set the IP
addresses manually.

Note

● When setting an IP address manually, ask the network
administrator or your internet service provider which
IP address to use. If the IP address is set wrong, the
network may go down or Internet access may be disabled.

● To congure the Scan to Local PC function via the WSD
Scan connection, follow these instructions.

- Conform the IP version of the machine to that of your
computer.

- Set [TCP/IP] setting to [Enable] on your machine.
(By factory default, it is set to [Enable].)

- Set [WSD Scan] setting to [Enable] on your
machine. (By factory default, it is [Enable]. If it
has been disabled, enable it by referring to the

Conguration Guide > “Conguring the scanning

to Local and Remote PCs” > “Using Functions for
Scanning to Local and Remote PCs” > “Enabling the
WSD Scan”.)

15 Remove “Software DVD-ROM” from the

computer.

The installation is complete.

- 80 -

Scanning to Local PC

Memo

● If conguring a small network consisting of only your
machine and a computer, set IP addresses as shown
below (according to RFC1918).

For the computer

IP address : 192.168.0.1~254

Subnet mask : 255.255.255.0

Default gateway : not used

DNS server : not used

For the machine

IP Address Set : Manual

IPv4 Address : 192.168.0.1~254

(select a different value
from the computer)

Subnet Mask : 255.255.255.0

Gateway Address : 0.0.0.0

Network Scale : Small

● To set [Network Scale], press the <SETTING> key
and then select [Admin Setup] > [Network Menu] >
[Network Setup] > [Network Scale].

1 Prepare an Ethernet cable and a hub.

Prepare an Ethernet cable (category 5, twisted
pair, straight) and a hub separately.

3 Plug one end of the Ethernet cable into

the network interface connection on the
back of the machine.

4

Scanning

4 Plug the other end of the Ethernet cable

into the hub.

2 Hold down the power switch for

approximately one second to turn off the
power.

5 Hold down the power switch for

approximately one second to turn on the
power.

- 81 -

Scanning to Local PC

6 Press the <SETTING> key on the

operator panel.

7 Press the to select [Easy Setup], and

press OK.

4

Scanning

8 Enter the administrator password.

The factory default password is “aaaaaa”.

c Press the and to select [Enter]

and press OK.

9 Press the to select [Network

Setting], and then press the .

10 If setting the IP address manually, check

that [Manual] is selected, and press OK.

If obtaining the IP address automatically, press
the to select [Auto], and press OK. Proceed to
the step 15.

a Press , , , to select the

character you want, and then
press OK.

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter
the correct value.

11 Enter the IP address using the ten-key

pad, and press OK.

To move to the next box, press the .

12 Enter the subnet mask using the ten-key

OK

pad, and press

To move to the next box, press the .

.

b Repeat step a until all characters

required are entered.

13 Enter the default gateway address using

the ten-key pad, and press OK.

To move to the next box, press the .

- 82 -

Scanning to Local PC

14 Enter the DNS server and WINS server if

needed.

If it is not necessary to connect the DNS server
or WINS server to the network, press
pop-up message showing setting completion is
displayed.

OK

until the

15 When the setup menu screen is

displayed, press
setup.

to complete the

16 For the conrmation message, check

that [Yes] is selected and press OK.

◆ Print the Network Information to check that
the IP address and other network information
are properly set.

 Step 2 Installing Your Machine to the

Computer

Memo

● The following procedure installs the WIA driver as a
scanner driver automatically.

1 Click [Start] and select [Control

Panel].

2 Select [Network and Internet] >

[Network and Sharing Center].

3 Select [Change advanced sharing

settings].

4 Check that [Turn on network

discovery] is selected.

4

Scanning

1 Press the <SETTING> key on the

operator panel.

2 Check that [Reports] is selected and

press OK.

3 Press the to select [System] and

press OK.

4 Press the to select [Network

Information] and press OK.

5 For the conrmation message, check

that [Yes] is selected and press OK.

The Network Information is printed.

5 Close the Control Panel.

6 Click [Start] and select [Network].

The devices connected to the network are
displayed.

7 Right-click the MC362 icon under

[Multifunction Devices] and select
[Install].

If the [User Account Control] dialog box is
displayed, click [Yes].

- 83 -

Scanning to Local PC

8 When the balloon message saying that

the installation is complete is displayed
on the task bar, click the balloon to
check the details, and click [Close].

4

9 Press the <SCAN> key on the operator

Scanning

panel.

For Mac OS X

 Overview

 Connecting Methods

You can select either of the following connection
methods:

● Network Connection

● USB Connection

 Product Requirements

Your machine supports Mac OS X 10.6 to 10.7.

 Steps to Go

To congure the Scan to Local PC function with

Mac OS X, follow the 3 steps below:

● “Step 1 Connecting Your Machine and

Computer” P.85

● “Step 2 Installing a Scanner Driver” P.88

10 Press the to select [Local PC] and

then press OK.

11 Check that [Select A Connecting PC]

is selected, and press OK.

12 Press the to select [From WSD

Scan], and press OK.

13 Check that the computer on which your

machine has been installed is displayed
as the destination PC.

Note

● If the machine’s IP address is changed after the
installation, uninstall the machine from the computer by
following the same procedure as in “Step 2 Installing Your

Machine to the Computer” P.83, and then reinstall it.

● “Step 3 Registering Your Computer in Network

Scanner Setup Tool” P.89

Memo

● For the network connection, you can skip step 1 if the IP
address is already set on your machine.

● You can skip step 2 if the scanner driver is already
installed on your computer.

● For the USB connection, skip step 3.

- 84 -

Scanning to Local PC

 Step 1 Connecting Your Machine

and Computer

Select the connection method and follow each
procedure.

● “For Network Connection” P.85

● “For USB Connection” P.88

 For Network Connection

Connect your machine to a network with an

Ethernet cable, and then congure the machine’s

IP address and other network information from
the operator panel. You can set the IP address
either manually or automatically.

If there is no DHCP server or BOOTP server on

the network, you need to manually congure the

IP address on the computer or machine.

If your network administrator or internet

service provider species a unique IP address

for the computer and your machine, set the IP
addresses manually.

Note

● You need to congure the network setting of the computer
before this procedure.

● When setting an IP address manually, ask the network
administrator or your internet service provider which IP
address to use. If the IP address is set incorrectly, the
network may go down or Internet access may be disabled.

● To congure the Scan to Local PC function via the network
connection, follow these instructions.

- Conform the IP version of the machine to that of your
computer.

- Set [TCP/IP] setting to [Enable] on your machine.
(By factory default, it is set to [Enable].)

- Set [Network TWAIN] setting to [ON] on your
machine. (By factory default, it is set to [ON]. If
it has been disabled, enable it by referring to the

Conguration Guide > “Conguring the scanning

to Local and Remote PCs” > “Using Functions for
Scanning to Local and Remote PCs” > “Enabling the
Network TWAIN Setting”.)

Memo

● If conguring a small network consisting of only your
machine and a computer, set IP addresses as shown
below (according to RFC1918).

For the computer

IP address : 192.168.0.1~254

Subnet mask : 255.255.255.0

Default gateway : not used

DNS server : not used

For the machine

IP Address Set : Manual

IPv4 Address : 192.168.0.1~254

(select a different value
from the computer)

Subnet Mask : 255.255.255.0

Gateway Address : 0.0.0.0

Network Scale : Small

● To set [Network Scale], press the <SETTING> key
and then select [Admin Setup] > [Network Menu] >
[Network Setup] > [Network Scale].

1 Prepare an Ethernet cable and a hub.

Prepare an Ethernet cable (category 5, twisted
pair, straight) and a hub separately.

2 Hold down the power switch for

approximately one second to turn off the
power.

4

Scanning

- 85 -

Scanning to Local PC

3 Plug one end of the Ethernet cable into

the network interface connection on the
back of the machine.

4

Scanning

4 Plug the other end of the Ethernet cable

into the hub.

6 Press the <SETTING> key on the

operator panel.

7 Press the to select [Easy Setup], and

press OK.

8 Enter the administrator password.

The factory default password is “aaaaaa”.

5 Hold down the power switch for

approximately one second to turn on the
power.

a Press , , , to select the

character you want, and then
press OK.

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter
the correct value.

- 86 -

b Repeat step a until all characters

required are entered.

Scanning to Local PC

c Press the and to select [Enter]

and press OK.

9 Press the to select [Network

Setting], and then press the .

10 If setting the IP address manually, check

that [Manual] is selected, and press OK.

If obtaining the IP address automatically, press
the to select [Auto], and press OK. Proceed to
step 15.

11 Enter the IP address using the ten-key

pad, and press OK.

14 Enter the DNS server and WINS server if

needed.

If it is not necessary to connect the DNS server
or WINS server to the network, press
the pop-up message of showing the setting
completion is displayed.

OK

until

15 When the setup menu screen is

displayed, press
setup.

to complete the

16 For the conrmation message, check

that [Yes] is selected and press OK.

◆ Print the Network Information to check that
the IP address and other network information
are properly set.

1 Press the <SETTING> key on the

operator panel.

4

Scanning

To move to the next box, press the .

12 Enter the subnet mask using the ten-key

OK

pad, and press

To move to the next box, press the .

.

13 Enter the default gateway address using

the ten-key pad, and press OK.

To move to the next box, press the .

2 Check that [Reports] is selected and

press OK.

3 Press the to select [System] and

press OK.

4 Press the to select [Network

Information] and press OK.

5 For the conrmation message, check

that [Yes] is selected and press OK.

The Network Information is printed.

- 87 -

Scanning to Local PC

 For USB Connection

1 Prepare a USB cable.

A USB cable is not supplied with your machine.
Prepare a USB 2.0 cable separately.

Memo

● Use a USB 2.0 Hi-Speed cable for a USB 2.0 Hi-
Speed connection.

2 Hold down the power switch for

4

Scanning

approximately one second to turn off the
power. And turn off the computer.

4 Plug the other end of the USB cable into

the computer’s USB interface connector.

Note

● Do not plug the USB cable into the network interface
connection. Doing so may damage your machine.

 Step 2 Installing a Scanner Driver

1

Check that the machine is connected to
the computer and the machine is turned
on. Then, load the “Software DVD-ROM”
on the drive of the computer.

3 Plug one end of the USB cable into the

USB interface connector on the back of
the machine.

2 Double-click [OKI] on the desktop.

3 Double-click [Drivers] > [Scanner] >

[Installer for Mac OSX].

4 Click [Continue].

5 Click [Continue].

- 88 -

Scanning to Local PC

6 Check the display and click [Continue]

if OK.

7 Read the license agreement and click

[Continue].

11 Click [Continue Installation].

12 Click [Restart].

4

Scanning

 Step 3 Registering Your Computer

in Network Scanner Setup Tool

8 Click [Agree] if you agree.

9 Click [Install].

To change the installation location of the driver,
click [Change Install Location].

To use the Scan to Local PC function via the
network connection, be sure to register your
computer as a destination in Network Scanner
Setup Tool before starting a scan job.

Memo

● Network Scanner Setup Tool is installed simultaneously
when installing the scanner driver.

1 From the [Go] menu, select

[Applications] > [OKIDATA] >
[Scanner] > [Network Scanner Setup
Tool].

2 Select your machine from [Device List]

and click [Register].

3 Edit [Name] which is displayed as

a destination on your machine if
necessary, and click [Register].

4 For the conrmation message, click

[OK].

10 Enter the administrator’s name and

password and then click [Install
Software].

5 Click [OK] to close the Network Scanner

Setup Tool.

- 89 -

Scanning to Local PC

Procedure for Scan to Local PC

This section explains how to start Scan to Local
PC. The following procedure is common for
Windows and Mac OS X.

You need to congure the initial settings before

using the Scan to Local PC function.

Select the connection method and follow each
procedure.

● “For Network Connection” P.90

● “For USB Connection” P.91

● “For WSD Scan Connection (Windows only)”

4

Scanning

P.93

 For Network Connection

Note

● For Mac OS X 10.7, if you scan documents through
network connection, you need to start the Image Capture

rst. Then, you need to select the machine from the list

displayed at the left of Image Capture screen.

2 Place your document in the ADF or on

the document glass as below:

● ADF

Load documents face up with the top edge of the

documents in rst.

Adjust the document guides to the width of your
documents.

● Document Glass

Place the document face down and align its top
edge to the upper-left corner of the glass.

1 Press the <SCAN> key on the operator

panel.

Close the document glass cover gently.

Note

● Do not apply an excessive load to the document
glass.

- 90 -

Memo

● The machine prioritizes the ADF when scanning
documents. Be sure not to place documents on the
ADF when you use the document glass.

Note

● If Carriage Error <02> is displayed, press Power
OFF/ON.

Scanning to Local PC

3 Press the to select [Local PC] and

then press OK.

4 Check that [Select A Connecting PC]

is selected and then press OK.

5 Check that [From Network] is selected

and then press OK.

6 Press the to select the computer you

want and then press OK.

7 Press the to select [Select An

Application] and then press OK.

8 Press the to select where to send the

scanned document and then press OK.

 For USB Connection

1

Press the <SCAN> key on the operator
panel.

4

Scanning

Selectable location Values to send:
Application Folder PC-FAX

Note

● For Mac OS X, you can select [Folder] only.

9 Press

ActKey (for Windows) or Image Capture (for
Mac OS X) starts, and the scan job starts
automatically on the computer. When scanning is
done, the scanned image is processed as below:

MONO

or

COLOR

.

- If you select [Application], the specied
application starts and the scanned image
is displayed on the application.

- If you select [Folder], the scanned image

is saved in the specied folder.

- If you select [PC-FAX], the application for
fax transmission starts. After sending the
scanned image, send a fax with the fax
transmission software on your computer.

Reference

● To load a landscape document, refer to the User’s Guide >
“Operation” > “Loading document(s)”.

● You can customize the scan button settings of ActKey. For

details, refer to the Conguration Guide > “Conguring

the scanning to Local and Remote PCs” > “Using Drivers
and Software” > “Using ActKey Software” > “Setting the
Scan Button”.

- 91 -

Scanning to Local PC

2 Place your document in the ADF or on

the document glass as below:

● ADF

Load documents face up with the top edge of the

documents in rst.

4

Scanning

Adjust the document guides to the width of your
documents.

● Document Glass

Place the document face down and align its top
edge to the upper-left corner of the glass.

3 Press the to select [Local PC] and

then press OK.

4 Check that [Select A Connecting PC]

is selected and then press OK.

5 Press the to select [From USB

Interface] and then press OK.

6 Press the to select [Select An

Application] and then press OK.

7 Press the to select where to send the

scanned document and then press OK.

Selectable location Values to send:
Application Folder PC-FAX

Close the document glass cover gently.

Note

● Do not apply an excessive load to the document
glass.

Memo

● The machine prioritizes the ADF when scanning
documents. Be sure not to place documents on the
ADF when you use the document glass.

Note

● If Carriage Error <02> is displayed, press Power
OFF/ON.

Note

● For Mac OS X, you can select [Folder] only.

8 Press

ActKey (for Windows) or Image Capture (for
Mac OS X) starts, and the scan job starts
automatically on the computer. When scanning is
done, the scanned image is processed as below:

MONO

or

COLOR

.

- If you select [Application], the specied
application starts and the scanned image
is displayed on the application.

- If you select [Folder], the scanned image

is saved in the specied folder.

- If you select [PC-FAX], the application for
fax transmission starts. After sending the
scanned image, send a fax with the fax
transmission software on your computer.

Reference

● To load a landscape document, refer to the User’s Guide >
“Operation” > “Loading document(s)”.

● You can customize the scan button settings of ActKey. For

details, refer to the Conguration Guide > “Conguring

the scanning to Local and Remote PCs” > “Using Drivers
and Software” > “Using ActKey Software” > “Setting the
Scan Button”.

- 92 -

Scanning to Local PC

 For WSD Scan Connection

(Windows only)

1

Press the <SCAN> key on the operator
panel.

2 Place your document in the ADF or on

the document glass as below:

● ADF

Load documents face up with the top edge of the

documents in rst.

Note

● Do not apply an excessive load to the document
glass.

Memo

● The machine prioritizes the ADF when scanning
documents. Be sure not to place documents on the
ADF when you use the document glass.

Note

● If Carriage Error <02> is displayed, press Power
OFF/ON.

3 Press the to select [Local PC] and

then press OK.

4

Scanning

Adjust the document guides to the width of your
documents.

● Document Glass

Place the document face down and align its top
edge to the upper-left corner of the glass.

Close the document glass cover gently.

4 Check that [Select A Connecting PC]

is selected and then press OK.

5 Press the to select [From WSD Scan]

and then press OK.

6 Press the to select the event for the

destination computer and then press OK.

Selectable events:
Scan for E-mail to XXX
Scan for Fax to XXX
Scan for OCR to XXX
Scan for Print to XXX
Scan to XXX

XXX indicates the name of the destination computer.

You can set an action for each event in Windows
scan properties.

- 93 -

Scanning to Local PC

7 Press

The scan job is processed according to the action
set for the selected event.

Reference

● To load a landscape document, refer to the User’s Guide >
“Operation” > “Loading document(s)”.

● You can scan double-sided documents. For details on
dual-side scanning, refer to the User’s Guide >
“Scanning” > “Scan to Local PC” >

MONO

or

.

COLOR

“WSD Scan connection”.

4

Scanning

- 94 -

5 Printing

This chapter explains the initial setup and basic procedure for the Print from Computer function.

Your machine supports the following print functions.

Function Overview

“Printing from a Computer” Prints a document sent from a computer connected via USB or network. The

printer driver must be installed on the computer to use this function.

Printing from USB Memory Prints a document saved in a USB memory which is inserted to the USB port of

the machine.
For the procedure of the function, refer to the User’s Guide > “Printing” >
“Printing From USB Memory”.

●● Printing from a Computer

This section explains how to install a printer driver and the basic procedure for printing documents from
a computer.

5

Be sure to install a printer driver before using this function.

Installing a Printer Driver

This section explains how to install a printer
driver on your computer.

Refer to the procedure for the OS you are using.

● “For Windows” P.95

● “For Mac OS X” P.103

For Windows

 Overview

 Connecting Methods

You can select either of the following connection
methods:

● “For Network Connection” P.96

● “For USB Connection” P.100

 Product Requirements

Your machine supports the following Windows
operating systems:

● Windows 7/Windows 7 (64bit Version)

● Windows Vista/Windows Vista (64bit Version)

● Windows Server 2008 R2

● Windows Server 2008/Windows Server 2008
(x64 Version)

● Windows XP/Windows XP (x64 Version)

● Windows Server 2003/Windows Server 2003
(x64 Version)

 Types of Printer Drivers

The printer driver types that can be installed are
as follows.

Type Description

PCL The PCL printer driver is suitable for

PS The PS printer driver is suitable for

PCL XPS The PCL XPS printer driver is suitable for

Printing

printing business documents.

the printing of documents including
PostScript fonts and EPS data.

printing from an application for XPS.

* It does not support Windows XP/ Windows

Server 2003.

- 95 -

Memo

● The description may be differ depending on a version of a
printer driver or Windows.

Printing from a Computer

 For Network Connection

To install a printer driver on your computer
via the network connection, follow the 2 steps
below:

● “Step 1 Conguring the Network Settings of

Your Machine” P.96

● “Step 2 Installing a Printer Driver” P.98

Note

● You need to complete the network setting of the computer
before this procedure.

Memo

● You can skip the step 1 if the IP address is already set on
your machine.

● You can skip the step 2 if the printer driver is already
installed on your computer.

 Step 1 Conguring the Network

Settings of Your Machine

Connect your machine to a network with an

5

Ethernet cable, and then congure the machine’s

IP address and other network information from

Printing

the operator panel. You can set the IP address
either manually or automatically.

If there is no DHCP server or BOOTP server on

the network, you need to manually congure the

IP address on the computer or machine.
If your network administrator or internet

service provider species a unique IP address

for the computer and your machine, set the IP
addresses manually.

Note

● When setting an IP address manually, ask the network
administrator or your internet service provider which
IP address to use. If the IP address is set wrong, the
network may go down or Internet access may be disabled.

● Conform the IP version of the machine to that of your
computer.

● Set [TCP/IP] setting to [Enable] on your machine. (By
factory default, it is set to [Enable].)

Memo

● If conguring a small network consisting of only your
machine and a computer, set IP addresses as shown
below (according to RFC1918).

For the computer

IP address : 192.168.0.1~254

Subnet mask : 255.255.255.0

Default gateway : not used

DNS server : not used

For the machine

IP Address Set : Manual

IPv4 Address : 192.168.0.1~254

Subnet Mask : 255.255.255.0

Gateway Address : 0.0.0.0

Network Scale : Small

(select a different value
from the computer)

1 Prepare an Ethernet cable and a hub.

Prepare an Ethernet cable (category 5, twisted
pair, straight) and a hub separately.

2 Hold down the power switch for

approximately one second to turn off the
power. And turn off the computer.

3 Plug one end of the Ethernet cable into

the network interface connection on the
back of the machine.

● To set [Network Scale], press the <SETTING> key
and then select [Admin Setup] > [Network Menu] >
[Network Setup] > [Network Scale].

- 96 -

Printing from a Computer

4 Plug the other end of the Ethernet cable

into the hub.

5 Hold down the power switch for

approximately one second to turn on the
power.

a Press , , , to select the

character you want, and then
press OK.

- The selected character is entered as “*” in

the text eld.

- If you have entered an incorrect value,
press the <CLEAR> key and then enter
the correct value.

5

Printing

6 Press the <SETTING> key on the

operator panel.

7 Press the to select [Easy Setup], and

press OK.

b Repeat step a until all characters

required are entered.

c Press the and to select [Enter]

and press OK.

9 Press the to select [Network

Setting], and then press the .

10 If setting the IP address manually, check

that [Manual] is selected, and press OK.

8 Enter the administrator password.

The factory default password is “aaaaaa”.

If obtaining the IP address automatically, press
the to select [Auto], and press OK. Proceed to
the step 15.

- 97 -

Printing from a Computer

11 Enter the IP address using the ten-key

pad, and press OK.

To move to the next box, press the .

5

12 Enter the subnet mask using the ten-key

Printing

pad, and press OK.

To move to the next box, press the .

13 Enter the default gateway address using

the ten-key pad, and press OK.

To move to the next box, press the .

14 Enter the DNS server and WINS server if

needed.

If it is not necessary to connect the DNS server
or WINS server to the network, press OK until the
pop-up message showing setting completion is
displayed.

◆ Print the Network Information to check that
the IP address and other network information
are properly set.

1 Press the <SETTING> key on the

operator panel.

2 Check that [Reports] is selected and

OK

press

.

3 Press the to select [System] and

press OK.

4 Press the to select [Network

Information] and press OK.

5 For the conrmation message, check

OK

that [Yes] is selected and press

The Network Information is printed.

 Step 2 Installing a Printer Driver

Note

● To complete this procedure, you must be logged in as an
administrator.

.

15 When the setup menu screen is

displayed, press to complete the
setup.

16 For the conrmation message, check

that [Yes] is selected and press OK.

1 Check that your machine and the

computer are turned on and connected,
and then insert the “Software DVD-ROM”
into the computer.

2 Click [Run Setup.exe] after [AutoPlay]

is displayed.

If the [User Account Control] dialog box is
displayed, click [Yes].

3 Select the language and then click

[Next].

- 98 -

Printing from a Computer

4 Select the device of your machine, and

then click [Next].

5 Read the license agreement and then

click [I Agree].

6 Read the “Environmental advice for

Users” and click [Next].

8 If the [Windows Security] dialog box

is displayed, click [Install this driver
software anyway].

9 Click the [Network] button.

The device search starts.

- If the machine is detected, it is
automatically installed. Proceed to step

11.

- If the machine is not detected, the
[Review your installation settings.]
screen is displayed. Proceed to step 10.

5

Printing

7 Select the checkbox for the printer

driver you want to install, and click the
Install bunch button.

Memo

● By factory default, [PCL driver], [Scanner driver],
and [ActKey] are selected.

10 Click [Restart search] to restart the

device search.

After the machine is displayed, select the machine
and click [Next].

Memo

● If the machine is not displayed by clicking [Restart
search], select [Printer name/IP Address] and

enter the IP address assigned to your machine, and
then click [Next].

- 99 -

11 If the [Windows Security] dialog box

is displayed, click [Install this driver
software anyway].

Printing from a Computer

12 Click the [Exit] button.

13 Remove the “Software DVD-ROM” from

the computer.

The installation is complete.

5

Printing

◆ Print a test page to check that the printer
driver is successfully installed on the
computer.

 For USB Connection

Follow the procedure below to connect a
USB cable and install a printer driver on your
computer.

Note

● You must be logged in as an administrator to complete
this procedure.

Memo

● You can skip this procedure if the printer driver is already
installed on your computer.

1 Prepare a USB cable.

A USB cable is not supplied with your machine.
Prepare a USB 2.0 cable separately.

Memo

● Use a USB 2.0 Hi-Speed cable for a USB 2.0 Hi-
Speed connection.

1 Click [Start] > [Devices and Printers].

2 Right-click the OKI MC562 icon and

select [Printer properties] (> a desired
printer driver if you have installed
multiple drivers) from the pop-up menu.

3 On the [General] tab, click [Print Test

Page].

2 Hold down the power switch for

approximately one second to turn off the
power.

3 Plug one end of the USB cable into the

USB interface connector on the back of
the machine.

- 100 -

4 Turn on the computer.