NTE5010T1 thru NTE5021T1 Zener Diode, 500mW
± 1% Tolerance
Features:
DZener Voltage 5.1V to 12V
DConstructed with an Oxide Passivated All Diffused Die
DDO35 Type Axial Lead Package
Absolute Maximum Ratings: |
|
|
|
|
|
|
||
Forward Voltage (IF = 100mA, TL = +30° C, Lead Length = 3/8”), VF . |
. . . . . . . . . . . . . |
. . . . . . |
. . 1.5V |
|||||
DC Power Dissipation (TL ≤ +50° C, Lead length = 3/8”), PD . . . . . . . . |
. . . . . . . . . . . . . |
. . . . . . |
500mW |
|||||
Derate Above 50° C |
. . . . . . . . |
. . . . . . . . . |
. . . . . . . . . |
. . . . . . . . . . . |
. . . . . . . . . . . . . |
. . 3.33mW/° C |
||
Operating Temperature Range, Topr |
. . . . . . . . |
. . . . . . . . . |
. . . . . . . . . . . |
. . . . . . . . . . –65° C to +200° C |
||||
Storage Temperature Range, Tstg . |
. . . . . . . . . |
. . . . . . . . . |
. . . . . . . . . . . |
. . . . . . . . . . –65° C to +200° C |
||||
Electrical Characteristics: (TL = +30° C, Lead Length = 3/8” unless otherwise specified) |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
Max DC |
Max Zener Impedance |
|
|
|
|
|
Nom Zener |
Zener |
Zener |
(Note 3) |
Typical |
Max Leakage |
||
|
Voltage |
Test |
Current |
|
|
Temperature |
||
|
|
Zzk @ |
||||||
NTE Type |
(Note 1) |
Current |
(Note 2) |
|
Coefficient |
Current |
||
Number |
Vz @ Izt |
(Izt) |
(Izm) |
Zzt @ Izt |
0.25mA (Izk) |
α vz |
IR @ VR |
|
|
Volts |
mA |
mA |
Ohms |
Ohms |
%/° C |
µ A |
Volts |
|
|
|
|
|
|
|
|
|
5010T1 |
5.1 |
5 |
98 |
50 |
2050 |
+0.025 |
2.0 |
2.0 |
|
|
|
|
|
|
|
|
|
5011T1 |
5.6 |
5 |
89 |
25 |
1800 |
+0.035 |
2.0 |
3.0 |
|
|
|
|
|
|
|
|
|
5013T1 |
6.2 |
5 |
81 |
10 |
1300 |
+0.040 |
1.0 |
4.0 |
|
|
|
|
|
|
|
|
|
5019T1 |
10.0 |
5 |
50 |
15 |
600 |
+0.065 |
0.1 |
8.0 |
|
|
|
|
|
|
|
|
|
5021T1 |
12.0 |
5 |
42 |
22 |
600 |
+0.073 |
0.1 |
9.1 |
|
|
|
|
|
|
|
|
|
Note 1. Voltage measurement to be performed 20 seconds after application of the DC test current. Note 2. The maximum zener current (Izm) shown is for the nominal voltages. The following formula
can be used to determine th worst case current for any tolerance device:
P
Izm = Vzm
Where Vzm is the high end of the tolerance specified and P is the rated power of the device. Note 3. Zener impedance is derived from the 1kHz AC voltage which results when an AC current having an RMS value equal to 10% of DC zener current (IZT or IZK) is superimposed on IZT
or IZK.
1.000 |
.200 |
(25.4) |
(5.08) |
Min |
Max |
.022 (.509) Dia Max |
.090 (2.28) |
|
Dia Max |
Color Band Denotes Cathode
Loading...