Nokia, Nokia Connecting People, Nokia 9290, and the Nokia Original Accessories logos are trademarks or registered trademarks of Nokia
Corporation. All other product and company names mentioned herein may be trademarks or tradenames of their respective owners.
Printed in Canada September/2002
Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of
Nokia is prohibited.
Includes RSA BSAFE cryptographic or security protocol software from RSA Security.
The information contained in this user guide was written for the Nokia 9290 communicator. Nokia operates a policy of continuous development.
Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice.
UNDER NO CIRCUMSTANCES SHALL NOKIA BE RESPONSIBLE FOR ANY LOSS OF DATA OR INCOME OR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL
OR INDIRECT DAMAGES HOWSOEVER CAUSED.
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED “AS IS.” EXCEPT AS REQUIRED BY APPLICABLE LAW, NO WARRANTIES OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE MADE IN RELATION TO THE ACCURACY AND RELIABILITY OR CONTENTS OF THIS DOCUMENT. NOKIA RESERVES THE RIGHT TO REVISE
THIS DOCUMENT OR WITHDRAW IT AT ANY TIME WITHOUT PRIOR NOTICE.
EXPORT CONTROLS
This product contains commodities, technology or software exported from the United States in accordance with the Export Administration
regulations. Diversion contrary to U.S. or Canadian law is prohibited.
FCC/INDUSTRY CANADA NOTICE
Your phone may cause TV or radio interference (for example, when using a telephone in close proximity to receiving equipment). The FCC or Industry
Canada can require you to stop using your telephone if such interference cannot be eliminated. If you require assistance, contact your local service
facility. This device complies with part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference.
The term “IC:” before the certification/registration number only signifies that Industry Canada technical specifications were met.
Message from the CTIA to all users of mobile phones. . . . . . . . . . . . . . . . . . 311
Appendix B
Message from the FDA to all users of mobile phones . . . . . . . . . . . . . . . . . . 315
FOR YOUR SAFETY Read these simple guidelines. Breaking the rules
may be dangerous or illegal. Further detailed information is given in
this User guide.
ROAD SAFETY COMES FIRST Do not use the communicator while
driving; park the vehicle first.
INTERFERENCE All wireless phones may get interference which could
affect performance.
SWITCH OFF IN HOSPITALS Follow any regulations or rules. Switch off
the phone near medical equipment.
SWITCH OFF IN AIRCRAFT Wireless phones can cause interference.
SWITCH OFF WHEN REFUELING Do not use the phone at a refueling
point. Do not use near fuel or chemicals.
SWITCH OFF NEAR BLASTING Do not use the phone where blasting is
in progress. Observe restrictions, and follow any regulations or rules.
USE SENSIBLY Use only in the normal position (to ear). Do not touch the
antenna unnecessarily.
USE QUALIFIED SERVICE Only qualified service personnel may install or
repair equipment.
ACCESSORIES AND BATTERIES Use only approved accessories and
batteries. Do not connect incompatible products.
MAKING CALLS VIA THE PHONE Close the cover and make sure the
phone is switched on and in service. Enter the phone number, including
the area code, then press . To end a call press . To answer a call
press .
EMERGENCY CALLS Close the device cover. Make sure the phone is
switched is on and in service. Hold for several seconds, to clear the
display. Enter the emergency number, then press . Give your location.
Do not end the call until told to do so.
MAKE BACKUP COPIES Remember to make backup copies of all
important data.
CONNECTING TO OTHER DEVICES When connecting to any other
device, read its user’s guide for detailed safety instructions. Do not
connect incompatible products.
INFRARED PRECAUTIONS Do not point the IR beam at anyone’s eye or
allow it to interfere with other IR devices.
DISCLAMER
It is possible that you may not be able to activate your phone on all wireless
systems. Please see your service provider for details.
USING THIS GUIDE
A number of features included in this guide are called System Services. They are
special services provided by wireless service providers. Before you can take advantage
of any of these System Services, you must subscribe to the service(s) from your
home service provider and obtain instructions for their use.
CONTACTING NOKIA
To help Nokia promptly answer your questions, please have your phone’s model
number, IMEI number, and your local zip code ready when you call Customer
Service. The IMEI and model number are on the back of your phone under the
battery. If you’re calling about an accessory, please have it available for reference.
Nokia Customer Care Center
7725 Woodland Center Boulevard
Suite 150
Tampa, FL 33614
Tel: 1-800-4MY-9290
Fax: 1-813-249-9619
For the TTY/TDD users only:
1-800-24-NOKIA (1-800-246-6542)
Customer Interaction Centre, Canada
Nokia Products Ltd.
601 Westney Rd. South
Ajax, Ontario L1S 4N7
Tel: 1-888-22-NOKIA (1-888-226-6542)
1. Getting started
Congratulations on purchasing the Nokia 9290 Communicator. It is a complete
communications tool: it is a wireless phone, messaging device, and a palmtop
organizer in one package.
When you open your sales package, check that it contains the following:
• The Nokia 9290 Communicator
• 16 MB Memory card
• The Nokia 9290 Communicator User Guide, theGetting Startedcard
(fold-out poster), and the Add-on applications guide
• High Power Battery BLL-3
• ACP-12U Charger
• RS232 DLR-2L Adapter Cable
• CD-ROM with PC connectivity software
•Headset
The Nokia 9290 Communicator consists of two parts: the phone and the communicator
interface. The phone is on the device cover and the communicator interface is
inside the cover, as shown in Figure 1.
communicator
interface
1
Getting started
Figure 1
2
Tip: The communicator
Getting started
interface has no power on/
off button - it switches on
when you open the cover
and switches off when you
close the cover.
Both these parts use the same information from the memory of the communicator they are not separate devices. For example, the phone uses the names and phone
numbers stored in the Contacts directory of the communicator interface, and the
communicator interface uses the phone for voice and data communications, for
example, when sending and receiving faxes and connecting to the Internet.
The communicator interface contains many organizer and communications
applications. The large keyboard, command buttons, and display make using the
applications easy.
The phone is designed for making and answering calls quickly. The communicator
looks and operates like other Nokia wireless phones, except the earpiece and
microphone are at the rear of the device. The phone is switched on and off by
pressing the button on the cover.
IMPORTANT: Do not switch on the phone when wireless phone use is
prohibited or when it may cause interference or danger.
Support options
To get the most from your Communicator, Nokia’s support options are
designed to be flexible and comprehensive. You can find online learning,
developer’s forums, and customer care. It is recommended that you view the
Getting Started CD-ROM in your 9290 Communicator sales packet. Support
options include:
• Getting Started CD-ROM This takes you through the basics and helps you
set up key Communicator features such as Short Message Service (SMS),
Internet access, and e-mail. It also provides step-by-step instructions for
using these and other features. You can also find additional software for
your Communicator and PC on this CD-ROM.
• www.Communicatorworld.net Visit this site to find the latest news about
the Communicator, download ring tones, images, and software. You can
also link to information on different development possibilities as well as
marketing support programs for developers, system integrators, and other
Nokia partners. The web site also links to information on documents, drivers,
quick guides, and information on compatibility issues.
• 1-800-4MY-9290 Nokia provides this toll free customer support line
specifically for Nokia 9290 Communicator owners.
• www.nokiahowto.com This web site is an interactive step-by-step user
manual to help you learn how to use all the features on your 9290
Communicator.
Using the phone
To be able to send and receive calls and messages on your Nokia 9290 Communicator,
you must have the following:
• the phone must be turned on,
• a valid SIM card must be inserted, and
• you must be located in the service area of the wireless network.
Emergency calls to the emergency number 911 or other official emergency numbers
may be made without the SIM card.
IMPORTANT: Your communicator can be locked with a lock code. The default
lock code is 12345. For security reasons, it is imperative that you
change the lock code. Keep the code secret and in a safe place,
separate from the communicator. For more information on
changing the lock code, see section ‘Security’ on page 230 of
the user guide.
3
Getting started
4
Getting started
First start-up
Note: Keep all miniature SIM cards out of the reach of small children.
When you subscribe for service, your service provider gives you a SIM card and a
phone number. The SIM card identifies your number to your service provider.
If you have several GSM 1900 phones, you can move the phone number from one
phone to another by moving the SIM card to the phone you wish to use.
WARNING: Support for features may vary with different service providers.
To start-up your phone:
1 Close the device cover and ensure that the phone is turned off.
If it is on, press .
2 If the battery is connected to the communicator, remove the battery. Press the
catch at the top of the of the battery and lift the battery away from the battery
cavity. Figure 2.
Figure 2
3 Slide the SIM card into the SIM card slot: ensure that the gold contacts of the
SIM card are facing down and that the bevelled corner of the card is on the
right. See Figure 3.
Figure 3
When the card is properly inserted into the SIM card slot, the bevelled corner
remains visible, as shown in Figure 4.
5
Getting started
Figure 4
bevelled corner is visible
6
Getting started
Tip: You can later change
the home city, time zone,
date, and time formats of
your communicator in the
Control panel with Date and
time and Regional settings
applications.
Tip: You can later attach
a picture to your business
card in the Contacts
application.
4 When you are sure that the SIM card is correctly installed, replace the battery.
If there is little or no charge in the battery, it is recommended that you connect
the communicator to the charger and start charging the battery before continuing
with the start-up procedure.
5 Open the cover of the communicator. You will see a welcome screen while the
communicator performs a self-test.
6 After the self-test is complete, if the choice of multiple keyboard layouts is
supported, you will be prompted to select the correct keyboard setup. Press OK
to confirm the keyboard selection.
If not, you will see a list of cities on the display.
7 Scroll to the name of your home city with the Arrows key and press OK. A view
showing the current time and date opens.
You can search for a city by typing the name of the city in the search field at
the bottom of the view.
8 Change the time and date if necessary and press OK.
9 Next you can modify your personal information in a business card. Press OK.
If a valid SIM card is inserted in your communicator, the business card may have
retrieved some information from the SIM card.
10 A note confirming that you have completed start-up successfully appears.
Press OK.
Note: The battery does not fit into place if the SIM card is not correctly installed.
Do not force the battery into place! Check that you have inserted the SIM
card into the slot as described above. If the SIM card is incorrectly installed,
remove it by pulling it out of the slot, and insert it again.
Memory card
The memory card supplied with your Nokia 9290 Communicator is already inserted
in the memory card slot. You can use a memory card to manage your documents,
contacts databases, applications, backups, and so on.
Use the items on the memory card in the same way as corresponding items on the
communicator. You can, for example, install and remove software to and from the
memory card with the Install/Remove software application, and send messages to
contacts in the contacts directory of the memory card.
Note: The memory card is hot-swap-capable between the Communicator and
some digital cameras, MP3 players, and PC card readers. However, file
formats may vary between the Communicator and other devices. Check the
user manual of your camera, MP-3 player, or PC card reader to determine
compatibility with the Communicator. Do not remove the memory card
while reading or saving a file.
Inserting a memory card
1 Close the device cover and make sure that the phone is switched off. If it is on,
press .
2 Open the hatch at the back of the communicator, using a minimum of two
fingers - one finger on each side of the hatch.
3 Slide the memory card under the memory card holder as shown in Figure 5.
Make sure that the gold contacts of the card are facing down.
Tip: To use the online
help, open the cover and
press the
(help) key.
7
Getting started
8
Getting started
Tip: To check the current
battery level, see the battery
indicator on the
communicator or phone
display.
Figure 5
4 When you have secured the card in place, close the hatch.
Charging the battery
Note: See important safety information on battery usage on page 9.
1 Connect the charger cable to the bottom of the communicator, as shown
in Figure 6.
Figure 6
2 Connect the charger to the proper voltage AC wall outlet. While charging is in
progress, the battery level indicator scrolls on the phone display.
3 When the battery is fully charged, the bars stop scrolling and four bars are
displayed. You may now remove the charger plug from the communicator.
Note: You can use all the features of the communicator during charging.
When the battery level is low and only a few minutes of operation time remain,
a warning tone will sound, and the message BATTERY IS LOW will be repeated
at regular intervals on the phone display. When the charge level becomes too
low for operation, the RECHARGE BATTERY message will be displayed, accompanied
by a warning tone. If you do not connect the communicator to a charger, the
communicator switches itself off.
Note: When you connect a communicator with a fully discharged battery to a
charger, it will take 30-60 seconds before the CHARGING message appears
on the display and the battery indicator bar starts scrolling. After that, it
may take 10-30 seconds before you can switch the phone on.
WARNING: Keep all SIM cards and memory cards out of the reach of
small children.
Battery information
Use the battery only for its intended purpose.
Never use any charger or battery that is damaged or worn out.
Do not short-circuit the battery. Accidental short-circuiting can occur when a
metallic object (for example coin, clip, or pencil) causes direct connection of the
+ and - terminals of the battery (metal strips on the bottom of the battery), for
example, when you carry a spare battery in your pocket or purse. Short-circuiting
the terminals may damage the battery or the connecting object.
9
Getting started
Tip: Read this section
for information on how to
prolong the life of your
battery.
10
Getting started
Leaving the battery in hot or cold conditions, such as in a closed car in summer or
winter conditions, will reduce the capacity and lifetime of the battery. Always try
to keep the battery between +15°C (+59°F) and +25°C (+77°F). A communicator
with a hot or cold battery may temporarily not work, even when the battery is fully
charged. The performance of Lithium-ion batteries is particularly limited in
temperatures below 0°C (+32°F).
Do not dispose of batteries in a fire!
Batteries must be recycled or disposed of properly. Batteries must not be disposed
of in municipal waste.
Note that a new battery’s full performance is achieved only after two or three
complete charge and discharge cycles.
Use only batteries approved by the communicator manufacturer and recharge the
battery only with the chargers approved by the manufacturer. With approved chargers
and accessories, the battery can be charged continuously.
The battery need not be fully discharged before recharging. When a charger is not
in use, disconnect it from the power source. Do not leave the battery connected to
a charger for longer than a week, since excessive charging may shorten its life.
If left unused, a fully charged battery will discharge itself over time.
The battery can be charged and discharged hundreds of times, but it will eventually
wear out. When the operating time (talk-time and stand-by time) is noticeably
shorter than normal, it is time to buy a new battery.
Temperature extremes will affect the ability of your battery to charge: allow it to
cool down or warm up first.
Battery operation time is affected by the following: whether both the phone and
the communicator interface are on, radio signal strength, various phone settings,
and the length of the screen blanker period.
It is always recommended to keep a charged battery in the communicator. Keeping
the battery charged maximizes the lifetime of the backup battery supplying power
to the real-time clock of the communicator. In case the backup battery is drained,
it will be automatically charged the next time a charged battery is reconnected to
the communicator.
Always close the device cover before removing the battery. Closing the cover will
save all data.
Note: The battery does not fit into place if the SIM card is not correctly installed.
Do not force the battery into place! Check that you have inserted the SIM
card as described in the Getting Started Guide. If the SIM card is incorrectly
installed, remove it by pulling it out of the slot, and insert it again.
11
Getting started
12
Getting started
Communicator interface
Display
Application
buttons
Command
buttons
Keyboard
Figure 7
The main features of the communicator interface, including the display, are shown
in Figure 7. The display is turned on simply by opening the cover. The application
that was active the last time the communicator was used is shown on the display.
When you close the cover, the communicator interface saves all data and turns off
its display.
Note: When you press Close, switch to another application, or close the device
cover, the Nokia 9290 Communicator saves all data automatically.
Help key
Menu key
Arrows key
Use the applications
The buttons at the top of the keyboard start the corresponding applications.
The application buttons are: Desk, Telephone, Messaging, Internet, Contacts, Calendar, Office, and Extras.
Loading...
+ 314 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.