Nokia 920C, 720C Service Manual

Download

Page 1

Manual

SERVICE

920C - 720C COLOR MONITOR

CONTENTS

1. Precautions

2. Product Specifications

3. Disassembly & Reassembly

4. Alignment & Adjustments

5. Troubleshooting

6. Exploded View & Parts List

7. Electrical Parts List

8. Block Diagram

9. Wiring Diagram

10. Schematic Diagrams

BH68-00294B rev. .2

Note: Sections 6, 8, 9 and 10 are in hardcopy format in the printed supplement.

Page 2

WARNINGS

1. For continued safety, do not attempt to modify the circuit board.

2. Disconnect the AC power before servicing.

3. When the chassis is operating, semiconductor heatsinks are potential shock hazards.

1-1-1 Servicing the High Voltage VR

and CRT :

WARNING:A high voltage VR replaced in the wrong

direction may cause excessive X-ray emissions.

Caution:

When replacing the high voltage adjustment VR, it must be fixed by a soldering iron after it is properly set.

1. When servicing the high voltage system, remove the static charge by connecting a 10 kohm resistor in series with an insulated wire (such as a test probe) between the chassis and the anode lead.

2. If the HV VR requires adjustment, (a) Replace the VR and adjust the high voltage to the specification. (b) Use a soldering iron to melt the adjustment cap on the HV VR to prevent any movement.

3. When troubleshooting a monitor with excessively HV, avoid being unnecessarily close to the monitor. Do not operate the monitor for longer than is necessary to locate the cause of excessive voltage.

4. High voltage should always be kept at the rated value, no higher. Only when high voltage is excessive are X-rays capable of penetrating the shell of the CRT, including the lead in glass material. Operation at high voltages may also cause failure of the CRT or high voltage circuitry.

5. When the HV regulator is operating properly, there is no possibility of an X-ray problem. Make sure the HV does not exceed its specified value and that it is regulating correctly.

6. The CRT is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the CRT only with one that is the same or equivalent type as the original.

7. Handle the CRT only when wearing shatterproof goggles and after completely discharging the high voltage anode.

8. Do not lift the CRT by the neck.

1-1-2 Fire and Shock Hazard :

Before returning the monitor to the user, perform the following safety checks:

1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor.

2. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc.

3. Leakage Current Hot Check (Figure 1-1):

WARNING: Do not use an isolation transformer during

this test.

Use a leakage current tester or a metering system that complies with American National Standards Institute (

ANSI C101.1, Leakage Current for

Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

4. With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unitÕs AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.

Figure 1-1. Leakage Current Test Circuit

1-1-4 Product Safety Notices

Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by

on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.

Components identified by on schematics and parts lists must be sealed by a soldering iron after replacement and adjustment.

720C/920C 1-1

1 Precautions

1-1 Safety Precautions

DEVICE UNDER TEST

TEST ALL

EXPOSED METAL

SURFACES

(READING SHOULD

NOT BE ABOVE 0.5mA)

LEAKAGE CURRENT

TESTER

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

EARTH

GROUND

Page 3

1. Servicing precautions are printed on the cabinet, and should be followed closely.

2. Always unplug the unitÕs AC power cord from the AC power source before attempting to: (a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect all test components in parallel with an electrolytic capacitor.

3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.

4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the area around the serviced part has not been damaged.

1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wriststrap device. To avoid a shock hazard, be sure to remove the wrist strap before applying power to the monitor.

2. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge.

3. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs.

4. Use only a grounded-tip soldering iron to solder or desolder ESDs.

5. Use only an anti-static solder removal device. Some solder removal devices not classified as Òanti-staticÓ can generate electrical charges sufficient to damage ESDs.

5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500 V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm.

7. Never defeat any of the +B voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

8. Always connect a test instrumentÕs ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrumentÕs ground lead last.

6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

7. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

Caution: Be sure no power is applied to the

chassis or circuit and observe all other safety precautions.

8. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD.

9. Indicates ESDs on the Schematic Diagram in this manual.

1 Precautions

1-2 720C/920C

1-3 Electrostatically Sensitive Devices (ESD) Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some fieldeffect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.

1-2 Servicing Precautions

WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances

create conflict between the servicing precautions and safety precautions, always follow the safety precautions.

WARNING2: A high voltage VR replaced in the wrong direction may cause excessive X-ray

emissions.

WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.

Page 4

2 Product Specifications

2-1 Specifications

Picture Tube: 17-Inch (43 cm): 16-inch (40.6 cm) viewable, 19-Inch (48.2 cm): 18-inch (45.8 cm) viewable,

17”/19”: 0.26 mm Dot pitch Full-square flat-face tube, 90˚ Deflection (720C), 100˚ Deflection (920C), Anti-Reflection coating with Anti-electrastatic, Medium short persistence phosphor

Scanning Frequency Horizontal : 720C/920C: 30 kHz to 96 kHz (Automatic), (Automatic)

Vertical : 50 Hz to 160 Hz (Automatic)

Display Colors Unlimited colors

Maximum Resolution Horizontal : 17”/19”/: 1600 Dots

Vertical : 17”/19”/: 1200 Lines

Input Video Signal Analog, 0.7 Vp-p positive at 75 Ω, internally terminated

Input Sync Signal Separate Sync : TTL level positive/negative

Composite Sync : TTL level positive/negative Sync-on-Green : Composite sync 0.3 Vp-p negative (Video on Vp-p positive)

Maximum Pixel Clock rate 17”/19" : 205 MHz

Active Display 17” ; Horizontal : 310 mm ± 3 mm (12.2” ± 0.12”)

Vertical : 232 mm ± 3 mm (9.13” ± 0.12”)

19” ; Horizontal : 355 mm ± 3 mm (13.98” ± 0.12”)

Vertical : 266 mm ± 3 mm (10.47” ± 0.12”)

Input Voltage AC 90 to 264 Volts, 60/ 50 Hz ± 3 Hz

Power Consumption (max) 17”: 120 Watt , 19”: 135 Watt

Dimensions Unit ; 17” : 16.3 x 16.9 x 17.2 Inches (415.0 x 430.3 x 438 mm)

(W x D x H) 19” : 18.4 x 19.6 x 19.0 Inches (468.0 x 499.0 x 483.2 mm)

Carton ; 17” : 21.1 x 22.3 x 21.9 Inches (535 x 566 x 555 mm)

19” : 22.6 x 23.2 x 22.8 Inches (573.0 x 590.0 x 580.0 mm)

Weight (Net/Gross) 17” : 39.0 lbs (17.7 kg) / 45.6 lbs (20.7 kg) (Net/Gross) 19” : 49.6 lbs (22.5 kg) / 58.8 lbs (26.7 kg)

Environmental Considerations Operating Temperature : 32°F to 104°F (0°C to 40°C)

Humidity : 10 % to 80 % Storage Temperature : -4°F to 113°F (-20°C to 45°C) Humidity : 5 % to 95 %

• 920C/720C complies with TCO 99 recommendations for reduced electromagnetic fields.

• Designs and specifications are subject to change without prior notice.

720C/920C 2-1

Item Description

Page 5

2 Product Specifications

2-2 720C/920C

QRS

Video

Sync

Horizontal

Vertical

CDE

Video

Sync

Separate Sync

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width C : Back porch D : Active time Q : Back porch R : Active time E : Front porch S : Front porch

Green

Vertical

Horizontal

Sync-on-Green

800/85 Hz 800 x 600

1600/75 Hz

1600 x 1200

1024/75 Hz

1024 x 768

640/85Hz

640 x 480

VGA2/70Hz

720 x 400

Table 2-1. Timing Chart

fH (kHz) A µsec B µsec C µsec D µsec E µsec fV (Hz) O msec P msec Q msec R msec S msec Clock

Freq. (MHz)

Polarity H.Sync

V.Sync Remark

31.469

31.778

3.813

1.907

25.422

0.636

70.087

14.268

0.064

1.080

12.711

0.413

28.322

Negative

Positive

Separate

43.269

23.111

1.556

2.222

17.778

1.556

85.008

11.764

0.069

0.578

11.093

0.023

36.000

Negative Negative Separate

60.023

16.660

1.219

2.235

13.003

0.203

75.025

13.328

0.050

0.466

12.795

0.017

78.75

53.674

18.631

1.138

2.702

14.222

0.569

85.061

11.756

0.056

0.503

11.179

0.019

56.250

Positive Positive

Separate

93.750

10.667

0.948

1.501

7.901

0.316

75.000

13.333

0.032

0.491

12.800

0.011

202.500

Positive Positive

Separate

Mode

IBM VESA MAC.

Timing

68.677

14.561

1.016

2.201

10.836

0.508

84.997

11.765

0.044

0.524

11.183

0.015

94.500

Positive Positive

Separate

49.726

20.110

4.117

3.910

14.524

0.559

75.000

13.414

0.060

0.784

12.549

0.020

57.284

SOG

68.681

14.560

1.280

1.440

11.520

0.320

75.062

13.322

0.044

0.568

12.667

0.044

100.000

Negative Negative

SOG

91.146

10.971

1.016

1.422

8.127

0.406

85.024

11.761

0.033

0.483

11.235

0.011

157.500

Positive Positive

Separate

79.976

12.504

1.067

1.837

9.481

0.119

75.025

13.329

0.038

0.475

12.804

0.013

135.000

Positive Positive

Separate

1024/85 Hz 1024 x 768

832/75 Hz 832 x 624

1152/75 Hz 1152 x 870

1280/75 Hz

1280 x 1024

1280/85 Hz

1280 x 1024

Negative Negative

Positive Positive

Separate

Page 6

3-1-1 Before making Disassembly

1.Disconnect power cord from the monitor.

2. With a pad beneath it, stand the monitor on its front with the screen facing downward and the base close to you.

3. Make sure nothing will damage the screen.

3-1-2 Cabinet Disassembly

1.Remove the 4 screws on the Rear Cover and pull it upward to remove it.

3-1-3 Removing the Stand

Pull the tab outward on the Chassis Bottom and pull the Tilt and Swivel Base up to remove it.

3-1-4 Removing the Top Shield

Remove the 4 screws on the Top Shield Cover and remove the Shield.

3-1-5 Removing the Bottom Shield

1. Remove the 1 screw on the Bottom Shield Cover.

2. Lift off the Bottom Shield.

3-1-6 Removing the Video PCB Assembly

1. Remove the Video PCB from the CRT.

2.Disconnect CN102, CN101, CN12 and CN13 on the Video PCB Assembly and Video PCB AssÕy from the CRT Neck.

720C/920C 3-1

3 Disassembly and Reassembly

This section of the service manual describes the disassembly and reassembly procedures for the Nokia 920C/720C (19" ~ 17") monitors.

WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling

these components.

3-1 Disassembly

Cautions:1. Disconnect the monitor from the power source before disassembly.

2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.

Page 7

3-1-7 Removing the Video PCB Assembly

Rear Shield and Video PCB

1. Remove the 3 screws on the PCB Assembly.

2. Remove the Video PCB Assembly Rear Shield. (5 point)

3. Lift out the Video PCB and pleat it on a flat, level surface that is protected from static electricity.

3-1-8 Removing the Main PCB Assembly

1. Remove both side screws (4 screws) on the lower edge of the CRT Bracket.

2. Remove Chassis Ground Wire on the both side.

3. Disconnect CN201, CN409, CN601, H_DY, CN604 and Anode Cap on the Main PCB Assembly.

3-1-9 Removing the Main PCB

1. Remove 6 screws on the main PCB.

2. Pull the Main PCB towards you and carefully lift out the main PCB and placet it on a flat, level surface that is protected from static electricity.

3-1-10 Removing the Bracket

1. Remove the 10 screws on the Front Cabinet.

3-1-11 Removing the Degaussing Coil

1. Using pinch-nosed pliers or long-nosed pliers, carefully push the 4 plastic ties on the Bracket.

2. Lift the Degaussing Coil Assembly from the Bracket.

3 Disassembly and Reassembly

3-2 720C/920C

3-2 Reassembly

Reassembly procedures are in the reverse order of Disassembly procedures.

Page 8

4-1-1 Before Making Adjustments

4-1-1 (a) ORIENTATION

When servicing, always face the monitor to the east.

4-1-1 (b) MAGNETIC FIELDS

Whenever possible, use magnetic field isolation equipment such as a Helmholtz field to surround the monitor. If a Helmholtz field is not available, frequently degauss the unit under test.

Caution: Other electrical equipment may cause

external magnetic fields which may interfere with monitor performance.

Use an external degaussing coil to limit magnetic build up on the monitor. If an external degaussing coil is not available, use the internal degaussing circuit. However, do not use the internal degaussing circuit more than once per 30 minutes.

4-1-1 (c) WARM-UP TIME

The monitor must be on for 30 minutes before starting alignment. Warm-up time is especially critical in color temperature and white balance adjustments.

4-1-1 (d) SIGNAL

Analog, 0.7 Vp-p positive at 75 ohm, internal termination Sync: Separate/Composite (TTL level negative/positive)

Sync-on-Green: Composite sync 0.3 Vp-p negative (Video 0.7 Vp-p positive)

4-1-1 (e) SCANNING FREQUENCY

Horizontal: 30 kHz to 96 kHz (Automatic) Vertical: 50 Hz to 160 Hz (Automatic)

Unless otherwise specified, adjust at the 1024 x 768 mode (H: 68 kHz, V: 85 Hz) signals.

Refer to Table 2-1 on pages 2-2 and 2-3.

4-1-1 (f) HIGH VOLTAGE ADJUSTMENT

Signal: 1024 x 768 mode (68 kHz/85 Hz) Display image: Full white Contrast: Maximum Brightness: Maximum Limit: 27.3 kV ± 0.5 kV

(17Ó: 26 kV ± 0.5 kV)

Measure the hight voltage level at the anode cap. High voltage should be within the limit as above. If the high voltage needs adjustment, use the VR501.

4-1-1 (g) G2 (SCREEN) VOLTAGE ADJUSTMENT

Signal: 1024 x 768 mode (68 kHz/85 Hz) Display image: Full white Contrast: Maximum Brightness: Maximum

Adjust the Screen VR of the FBT so that the G2 (Screen) Voltage for Toshiba it is 540 V ± 10 V.

4-1-1 (h) CENTER RASTER

Adjust VR401 so that the back raster comes to the center when you apply a signal of 91 kHz/85 Hz.

720C/920C 4-1

4 Alignment and Adjustments

This section of the service manual explains how to make permanent adjustments to the monitor. Direction is given for adjustment using the monitor Interface Board Ver. 2.0 and software (Softjig).

4-1 Adjustment Conditions

Caution: Changes made without the Softjig are saved only to the user mode settings. As such, the

settings are not permanently stored and may be inadvertently deleted by the user.

720C SDD TOSHIBA

G2 525V 635V

920C

G2 560V 530V

MEC SDD

Page 9

4-1-1 (i) BRIGHTNESS AND CONTRAST

Unless otherwise specified, adjust control volumes:

Brightness: Maximum Contrast: Maximum

4-1-2 Required Equipment

The following equipment may be necessary for adjustment procedures:

4-1-2 (a) DISPLAY CONTROL ADJUSTMENT

1. Non-metallic (Ð) screwdriver: 1.5 mm Non-metallic (Ð) screwdriver: 3 mm

2. Philips (+) screwdriver: 1.5 mm

3. Non-metallic hexkey: 2.5 mm

4. Digital Multimeter (DMM), or Digital Voltmeter (DVM)

5. Signal generator, or Computer with a video board that uses the ET-4000 chipset (strongly recommended if using Samsung DM 200 software) and that displays: 1280 x 1024 @ 85 Hz, or 1600 x 1200 @ 85 Hz (maximum).

6. Personal computer

7. Required software: Softjig.exe from Samsung which includes the Nokia19SDD.MDL (SDD CRT) data file Samsung DM200, or DisplayMate for Windows from Sonera Technologies

8. Interface Board Ver. 2.0 Code No. BH81-90001K

9. Parallel communications cable (25-pin to 25-pin); Code No. BH81-90001H

10. Signal cable (15-pin to 15-pin cable with additional 3-pin connector); Code No. BH81-90001J

11. 5 V DC adapter, not supplied

Note: Softjig AssÕy (includes items 8, 9 and 10)

Code No. BH81-90001L

4-1-2 (b) COLOR ADJUSTMENTS

1. All equipment listed in 4-1-2 (a), above

2. Color analyzer, or any luminance measurement equipment

4-1-3 Connecting the SoftJig

Connect the monitor to the signal generator and/ or PC as illustrated in Figures 4-1 and 4-2.

Note: The signal cable connector which includes

the 3-wire cable must connect to the monitor. If you use Setup 2 (PC only, no signal generator) you can only make adjustments to the signal timing available on that computer system. To make corrections to all factory timings requires the use of an additional signal generator.

4-1-4 After Making Adjustments

After finishing all adjustments, test the monitor in all directions. If, for example, the monitor does not meet adjustment specifications when facing north, reposition the monitor to face east and readjust. This time, try for an adjustment closer to the ideal setting within the tolerance range. Test the unit again in all directions. If the monitor again fails to meet specifications in every direction, contact your Regional After Service Center for possible CRT replacement.

4 Alignment and Adjustments

4-2 720C/920C

MONITOR

INTERFACE BOARD VER. 2.0

SIGNAL GENERATOR

3-WIRE CABLE

SIGNAL CABLE

5V DC ADAPTOR

PARALLEL CABLE

Figure 4-1. Setup 1, With Signal Generator

MONITOR

INTERFACE BOARD VER. 2.0

3-WIRE CABLE

SIGNAL CABLE

PARALLEL CABLE

D-SUB CONNECTOR

5V DC ADAPTOR

Figure 4-2. Setup 2, Without Signal Generator

Page 10

4-2-1 Centering

Centering means to position the center point of the display in the middle of the display area. Horizontal size and position and vertical size and position control the centering of the display.

Adjust the horizontal size and vertical size to their optimal settings: 355 mm (H) x 266 mm (V)/920C. 310 mm x 232 mm/720C. 1280 x 1024 mode (91kHz/85Hz)

Adjust the horizontal position and vertical position to ²4.0 mm of the center point of the screen.

|A-B| ² 4.0 mm. |C-D| ² 4.0 mm.

Figure 4-3. Centering

4-2-1 (a) HORIZONTAL SIZE ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to H_SIZE to adjust the horizontal size of the display pattern to 355 mm. (Tolerance: ±3 mm.)

4-2-1 (b) VERTICAL SIZE ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to V_SIZE to adjust the vertical size of the display pattern to 266 mm. (Tolerance: ±3 mm.)

4-2-1 (c) HORIZONTAL POSITION ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to H_POSI to center the horizontal image on the raster.

4-2-1 (d) VERTICAL POSITION ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to V_POSI to center the vertical image on the raster.

4-2-2 Linearity

Linearity affects the symmetry of images as they appear on the screen. Unless each row or column of blocks in a crosshatch pattern is of equal size, or within the tolerances shown in Tables 4-1 and 4-2, an image appears distorted, elongated or squashed.

Table 4-1. Factory Preset Modes Linearity

Table 4-2. Other Modes Linearity: VGA, SVGA, XGA,

MAC, etc.

4-2-2 (a) HORIZONTAL LINEARITY ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

To adjust the Horizontal Linearity, refer to Tables 4-1 and 4-2 for the tolerance range.

Click on the << or >> box next to H_LIN to optimize the image.

4 Alignment and Adjustments

720C/920C 4-3

4-2 Display Control Adjustments

DISPLAY AREA

EDGE OF BEZEL

4 : 3

Horizontal: 20.5~23.5 Vertical : 20.5~23.5

Supported Timing Mode

Each block (14 %)

Difference between

adjacent blocks (5 %)

Horizontal: Less than 1.10 mm Vertical : Less than 1.10 mm

4 : 3

Horizontal: 20.9~23.1 Vertical : 20.9~23.1

Standard Modes Linearity

Each block (10 %)

Difference between

adjacent blocks (4 %)

Horizontal: Less than 0.88 mm Vertical : Less than 0.88 mm

Page 11

4-2-2 (b) VERTICAL LINEARITY ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

To adjust the Vertical Linearity, refer to Tables 4-1 and 4-2 for the tolerance range.

Click on the << or >> box next to V_LIN to optimize the image.

4-2-3 Trapezoid Adjustment

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to TRAP to make the image area rectangular.

Figure 4-4. Trapezoid

4-2-4 Pinbalance Adjustment

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to PIN_BAL to optimize the image.

4-2-5 Parallelogram Adjustment

CONDITIONS

Scanning Frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to PARALLEL to make the image area rectangular.

Figure 4-6. Parallelogram

4-2-6 Side Pincushion Adjustment

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to BARREL to straighten the sides of the image area.

4-2-7 Tilt Adjustment

CONDITIONS

Scanning Frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to ROTATE to correct the tilt of the display.

4-2-8 Degauss

No adjustments are available for the degaussing circuit. The degaussing circuit can effectively function only once per 30 minutes.

4-2-9 To Delete the User Mode Data

To delete the adjustment data from the user modes, press the EXIT Button for 15 seconds.

4-2-10 Save the Data

To save the adjustment data for a mode, press

FACTORY SAVE.

4 Alignment and Adjustments

4-4 720C/920C

| C1 |, | C2 | ≤ 2.0 mm, | D1 |, | D2 | ≤ 2.0 mm.

Figure 4-7. Pincushion

5 mm

| D1 |, | D2 | ≤ 2.0 mm

Figure 4-5. Pinbalance

D1 D2 D1

D2D1

| A - B | < 5 mm

Page 12

4-3-1 Color Coordinates (Temperature)

Color temperature is a measurement of the radiant energy transmitted by a color. For computer monitors, the color temperature refers to the radiant energy transmitted by white. Color coordinates are the X and Y coordinates on the chromaticity diagram of wavelengths for the visible spectrum.

CONDITIONS

Measurement instrument: Color analyzer Scanning frequency: 68 kHz/85 Hz Display Size : 355 (H) x 266 (V)/920C ~ 310 X 232/720C Display image: White flat field at

center of display area Brightness:Cut-off Contrast: Maximum

PROCEDURE

Use the directions in sections 4-3-2 through 4-3-4 to adjust the color coordinates for: 9300K to x = 0.283 ±0.02, y = 0.297 ±0.02 6500K to x = 0.313 ± 0.02, y = 0.329 ± 0.02 5000K to x = 0.346 ± 0.02, y = 0.359 ± 0.02

4-3-2 Color Adjustments for 9300K

4-3-2 (a) BACK RASTER COLOR ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Back raster pattern Brightness: Cut-off Contrast: Maximum

1. Select COLOR CHANNEL 1 to control the

color for 9300K.

2. Adjust the luminance of the back raster to

between 0.3 to 1ft-L using the G_CUT controls.

3. Click on the << or >> box next to B_CUT to

set the ÒyÓ coordinate to 0.297 ±0.02.

4. Click on the << or >> box next to R_CUT to

set the ÒxÓ coordinate to 0.283 ± 0.02.

Note: If the above adjustments cannot be

done to each coordinate, click on the << or >> box next to G_CUT to decrease or increase the green cutoff (bias) and repeat procedures 2 and 3.

4-3-2 (b) G-GAIN ADJUSTMENT

Figure 4-8. Green Box Pattern

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Green box pattern Brightness: Cut-off Contrast: Maximum

1. Click on the << or >> box next to G_GAIN to adjust the brightness of the Green Gain to 25 ± 1 ft-L.

Note: If you canÕt increase the Green Gain to

the appropriate value, click on the >> box next to increase the ABL point.

4-3-2 (c) WHITE BALANCE ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Full white pattern Brightness: Cut-off Contrast: Maximum

Figure 4-9. Full White Pattern

1. Click on the << or >> boxes next to R_GAIN and B_GAIN to make the video white. (For 9300K color adjustment: x = 0.283 ±0.02, y = 0.297 ±0.02.)

Note: Do not touch the G_GAIN controls.

2. Check the ABL. If it is not within the specifications (30 ± 1 ft-L), use the ABL controls to adjust it.

3. Select COLOR FACTORY SAVE to save the data.

4 Alignment and Adjustments

720C/920C 4-5

4-3 Color Adjustments

1/3H-1/2H

1/3V-1/2V

FRONT BEZEL OPENING

BACK RASTER

GREEN WINDOW

FRONT BEZEL OPENING

BACK RASTER

WHITE WINDOW

Page 13

4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Back raster pattern X-Y Coordinates: x = 0.283 ± 0.02,

y = 0.297 ±0.02 Raster Luminance 0.3 ~ 1ft-L ABL Luminance 30 ± 1 ft-L Brightness: Cut-off Contrast: Maximum

1. Check whether the color coordinates of the

back raster satisfy the above spec. If they do not, return to 4-3-2 (a) and readjust

all settings.

2. Display a full white pattern.

Note: Do not touch the G_GAIN controls.

3. Adjust the Contrast Control on the monitor so

that the luminance of the video is about 5 ft-L.

4. Check whether the white coordinates of the

video meet the above coordinates spec.

5. Adjust the Contrast Control again so that the

luminance of the video is about 20 ft-L.

6. Check whether the white coordinates of the

video satisfies the above spec. If they do not, return to 4-3-2 (a) and readjust

all settings.

4-3-3 Color Adjustments for 6500K

4-3-3 (a) BACK RASTER COLOR ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Back raster pattern Brightness: Cut-off Contrast: Maximum

1. Select COLOR CHANNEL 2 to control the

color for 6500K.

2. Adjust the luminance of the back raster to

between 0.3 to 1.0 ft-L using the G_CUT controls.

3. Click on the << or >> boxes next to R_CUT

and B_CUT to adjust the R-Bias to x = 0.313 ±

0.02 and the B-Bias to y = 0.329 ± 0.02.

4-3-3 (b) G-GAIN ADJUSTMENT

This procedure is the same as that for 9300K, refer to the procedure on page 4-5.

4-3-3 (c) WHITE BALANCE ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Full white pattern Brightness: Cut-off Contrast: Maximum

1. Click on the << or >> boxes next to R_GAIN and B_GAIN to make the video white. (For 6500K color adjustment: x = 0.313 ± 0.02, y = 0.329 ± 0.02.)

2. Refer to the procedure for 9300K, section 4-3-2 (c) steps 2 and 3.

4-3-3 (d) WHITE BALANCE ADJUSTMENT VERIFICATION

Refer to the procedure for 9300K, section 4-3-2 (d).

4-3-4 Color Adjustments for 5000K

4-3-4 (a) BACK RASTER COLOR ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Back raster pattern Brightness: Cut-off Contrast: Maximum

1. Select COLOR CHANNEL 3 to control the color for 5000K.

2. Adjust the luminance of the back raster to between 0.3 to 1.0 ft-L using the G_CUT controls.

3. Click on the << or >> boxes next to R_CUT and B_CUT to adjust the R-Bias to x = 0.346 ±

0.02 and the B-Bias to y = 0.359 ± 0.02.

4-3-4 (b) G-GAIN ADJUSTMENT

This procedure is the same as that for 9300K, refer to the procedure on page 4-5.

Adjust the brightness of the G_GAIN less 5 ft-L than brightness of procedure for 9300K.

4-3-4 (c) WHITE BALANCE ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Full white pattern Brightness: Cut-off Contrast: Maximum

1. Click on the << or >> boxes next to R_GAIN and B_GAIN to make the video white. (For 5000K color adjustment: x = 0.346 ± 0.02, y = 0.359 ± 0.02.)

2. Refer to the procedure for 9300K, section 4-3-2 (c) steps 2 and 3.

4 Alignment and Adjustments

4-6 720C/920C

Page 14

4-3-4 (d) WHITE BALANCE ADJUSTMENT VERIFICATION

Refer to the procedure for 9300K, section 4-3-2 (d).

4-3-5 Luminance Uniformity Check

Luminance is considered uniform only if the ratio of lowest to highest brightness areas on the screen is not less than 7.5:10.

CONDITIONS

Scanning frequency: 68 kHz/85 Hz

(1024 x 768) Display image: White flat field Display size: 355(H) x 266(V)/920C ~ 310(H) X 232(V)/720C Brightness: Cut off point Contrast: Maximum

PROCEDURE

Measure luminance at nine points on the display screen (see figure below).

4-3-6 Focus Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: ÒHÓ character pattern Brightness: Cut off point Contrast: Maximum

PROCEDURE

1. Adjust the Focus VR on the FBT to display the

sharpest image possible.

2. Use Locktite to seal the Focus VR in position.

4-3-7 Color Purity Adjustment

Color purity is the absence of undesired color. Conspicuous mislanding (unexpected color in a uniform field) within the display area shall not be visible at a distance of 50 cm from the CRT surface.

CONDITIONS

Orientation: Monitor facing east Scanning frequency: 68 kHz/85 Hz Display image: White flat field Luminance: Cut off point at the center

of the display area

Note: Color purity adjustments should only be

attempted by qualified personnel.

PROCEDURE (adjusting convergence)

For trained and experienced service technicians only.

Use the following procedure to correct minor color purity problems:

1. Make sure the display is not affected by external magnetic fields.

2. Very carefully break the glue seal between the 2-pole purity convergence magnets (PCM), the band and the spacer.

3. Make sure the spacing between the PCM assembly and the CRT stem is 29 mm ± 1 mm.

4. Display a green pattern over the entire display area.

5. Adjust the purity magnet rings on the PCM assembly to display a pure green pattern. (Optimum setting: x = 0.295 ± 0.015, y = 0.594 ± 0.015)

6. Repeat steps 4 and 5 using a red pattern and then again, using a blue pattern.

Table 4-3. Color Purity Tolerances

(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.297 ± 0.02)

7.When you have the PCMs properly adjusted, carefully glue them together to prevent their movement during shipping.

4 Alignment and Adjustments

720C/920C 4-7

Red: x = 0.620 ± 0.015 y = 0.334 ± 0.015

Green: x = 0.289 ± 0.015 y = 0.595 ± 0.015

Blue: x = 0.153 ± 0.015 y = 0.072 ± 0.015

Figure 4-10 Luminance Uniformity Check Locations

Page 15

720C/920C 5-1

5 Troubleshooting

5-1 Parts Level Troubleshooting

Notes: 1. If a picture does not appear, fully rotate the brightness and contrast controls clockwise and reinspect.

2. Check the following circuits.

• No raster appears: Power circuit, Horizontal output circuit, H/V control circuit, and H/V output circuit.

• High voltage develops but no raster appears: Video output circuits.

• High voltage does not develop: Horizontal output circuits.

5-1-1 No Power Supply

Check and replace FG601, D601,

IC661, IC662.

Done.

Repeating start?

Check and replace D601, D604, D663,

Q632, and Q664.

Yes

IC601 Pin 1 waveform is right?

Check and replace IC601,

IC602, IC604.

Yes

IC602 and IC604

are right?

Replace parts and verify voltages.

Yes

Normal operation

Replace Main board.

Yes

WAVEFORMS

544 V (IC601, #1)

CH1 P-P = 544 V CH1 RMS = 332.4 V

Verify voltages.

Page 16

5 Troubleshooting

5-2 720C/920C

5-1-2 DPMS Failure

Check signal source

H/V sync video level.

Make no H/V sync (power off mode)

LED blinks

Check IC201 Pin 39.

Yes

+12 V line off

Check IC201 Pin 9.

Yes

Q632 Base driving voltage exists?

Check IC201 Pin 10.

Check and replace Q632.

Yes

Done

Page 17

5 Troubleshooting

720C/920C 5-3

5-1-3 H_Deflection Failure

IC402 Pin 6 waveform is right?

Q403 source waveform

is right?

Check D407, D408, Q403, R436

and R438, +210 V line.

Yes

1. Check R401, +12 V line.

2. Check IC402 Pins 6~5, 7~6.

3. Replace IC402.

Q404 gate, drain

waveforms are right?

Check Q404, R415.

Check +25 V line.

Yes

Q405 base, collector

waveforms are right?

Check and replace D410 and Q405.

Check DY connector connection.

Yes

IC261 Pin 4 is high?

Replace IC261.

Check some parts around

Q261 and Q262.

Yes

IC261 Pin 26 waveform

is right?

Check some parts around IC261.

Yes

WAVEFORMS

230 V (Q405, Source)

CH1 P-P = 230 V CH1 RMS = 150.1 V

12.08 V (IC261, #26)

CH1 P-P = 12.08 V CH1 RMS = 7.396 V

10.96 V (IC402, #6)

CH1 P-P = 10.96 V CH1 RMS = 6.180 V

54 V (Q404, Drain)

CH1 P-P = 54 V CH1 RMS = 22.44 V

11.6 V (Q404, Gate)

CH1 P-P = 11.6 V CH1 RMS = 6.944 V

18.6 V (Q405, Base)

CH1 P-P = 55.2 V CH1 RMS = 9.52 V

1.216 kV (Q405, Collector)

CH1 P-P = 1.216 kV CH1 RMS = 316 V

Check some parts around Q263.

Page 18

5 Troubleshooting

5-4 720C/920C

5-1-4 S Correction Failure

S1~S5 signals are right at each

frequency block?

Check S1 ~ S5 signal.

Check and replace

C430, C431, C433, C434, C435,

C437 C441, C453, C454, C455, C456, C457,

Q409~Q413, Q451~Q455, Q456~Q460 .

Yes

5-1-5 H_Lin. Failure

IC201 Pin 21 voltage varies with

different H_Lin. DAC values?

IC403 Pin 7, 8 voltage varies with

different H_Lin. DAC values?

Check +12 V line.

Check some parts around IC403.

Check L403.

Yes

Check and replace IC201.

Replace IC201.

5-1-6 Invariable H_Size

IC261 Pin 28 voltage varies with

different H_Size DAC values?

IC401 Pin 6 output duty varies with

different H_Size DAC values?

Check some parts around IC261 Pin

28, IC401.

Yes

Check and replace IC261.

Page 19

5 Troubleshooting

720C/920C 5-5

5-1-7 Abnormal H_Size

T402 Pin 8 waveform is right?

Check and replace T402.

Check some parts around D415, IC261

Pin 28, IC402 Pin 2 and IC201 Pin20.

Yes

5-1-8 Side Pin or Trap Failure

IC261 Pin 24 output exists?

Yes

Check and replace IC261.

Check and replace IC402.

Check some parts IC402 Pin 2

and IC261 Pin 24.

5-1-9 Para. or Pin Balance Failure

IC261 Pin 24 output varies with

different DAC values?

Replace IC261.

WAVEFORMS

29.8 V (T402, #8)

CH1 P-P = 29.8 V CH1 RMS = 7.14 V

Page 20

5 Troubleshooting

5-6 720C/920C

5-1-10 Tilt Failure

IC201 Pin 23 output duty varies

with different DAC values?

IC403 Pin 10, 11 output varies with

different DAC values?

Check and replace IC403.

Check and replace CRT.

Yes

Check and replace IC201.

Check tilt connector connection

5-1-11 V Deflection Failure

±14 V line is on?

IC261 Pin 23 output exists?

Check and replace IC261.

Yes

Refer to 5-1-1 No Power Supply

IC301 Pin 1 input exists?

Check R276 and R304.

Yes

IC301 Pin 6 output exists?

Check and replace some parts

around IC301.

Yes

Check V DY connector connection.

Page 21

5 Troubleshooting

720C/920C 5-7

5-1-12 V Size or Pos. Variation Failure

IC261 Pin 23 output varies with

different DAC values?

Yes

Check some parts around IC301.

Check bias voltage.

Check and replace IC261 and IC301.

5-1-13 High Voltage Failure

Q524 gate driving pulse exist?

Check +12 V line.

Check and replace Q521, Q522, Q523,

Q524 and IC501.

Yes

Done

Page 22

5 Troubleshooting

5-8 720C/920C

IC101 (17”: IC104, Pin12) Pin 15

input exists and

varies with different patterns?

Check and replace IC101

(17”:IC104)

Input full white pattern to monitor.

Yes

T501 Pin 8 output exists?

Check and replace T501.

Yes

IC103 (17”: IC04) Pin 16 output

exists and varies with different

patterns?

Check and replace IC103 (17”: IC04).

Yes

Check and replace Q101,

Q102 and +12 V line.

Check CN102.

5-1-14 ABL Failure

5-1-15 Dynamic Focus Failure

IC261 Pins 18 and 15 output

are right?

Check and replace IC261.

Yes

Some parts around Q551,

Q552, Q553 and Q554 are right?

Replace failed part.

Yes

Some parts around T502 are right?

Replace failed part.

Check the connection between FBT

Pin 13, CRT Socket PCB.

Yes

2.20 V (IC251, #15)

CH1 P-P = 2.20 V CH1 RMS = 2.776 V

580 V (T551, #1)

CH1 P-P = 580 V CH1 RMS = 278.2 V

WAVEFORMS

Page 23

5 Troubleshooting

720C/920C 5-9

5-1-16 No Video

IC101 Pins 2, 6 and 11 (17”: IC104,

Pin 5, 8, 10) inputs are right?

IC101 Pins 29, 32 and 35

(17”: IC104, Pin 25, 28, 30) outputs

are right?

Check I2C bus and +12 V line.

Yes

Check CN101

IC102 Pins 4, 6 and 14 (17”: IC105,

Pin 1, 3, 5) outputs are right?

Check +12 V line.

Check and replace IC102 (17”: IC105).

Yes

Cathode DC levels are right?

Check +80 V line.

Check and replace IC101 and IC104

(17”: IC104).

Yes

G2 voltage is right?

Check G2 wire, CRT Socket board,

and FBT.

Change CRT.

Yes

Done.

Check signal cable and connection.

Page 24

5 Troubleshooting

5-10 720C/920C

5-1-17 Micom Failure

IC201 Pin 11 input is right?

IC201 Pins 13 and 14 inputs

are right?

Check X201, C204 and C205.

Yes

Check IC606.

IC201 Pin 18 input is right?

Check IC202.

Yes

All in/output values are right?

Replace IC201.

Yes

Done

3.42 V (IC201, #33)

CH1 P-P = 3.42 V CH1 RMS = 2.500 V

3.16 V (IC201, #32)

CH1 P-P = 3.16 V CH1 RMS = 2.560 V

WAVEFORMS

Page 25

5 Troubleshooting

720C/920C 5-11

5-1-18 OSD Failure

IC103 (17”: IC04) Pin 17 input is

right?

IC103 (17”: IC04) Pin 6 input is

right?

Check and replace Q104 (17”: Q103) .

Yes

Check and replace D302 and Q301.

IC103 (17”: IC04) Pins 7 and 8

inputs are right?

Check IC201 Pins 41 and 42.

Yes

IC103 (17”: IC04) Pins 20, 21 and

22 outputs are right?

Check and replace IC103 (17”: IC04) .

Yes

IC101 (17”: IC104) Pins 4, 9 and 13

inputs are right?

Check and replace QB51,

QG51 and QR51.

Check and replace IC101 (17”: IC104) .

Yes

Done

Check CN102 and connector Ass’y.

(17” only)

Page 26

5 Troubleshooting

5-12 720C/920C

RL601 operation is right?

Q630 base input is right?

Check and replace Q630.

Yes

Check D-Coil, TH601.

Yes

IC201 Pin 40 output is right?

Check and replace IC201.

Check user function key.

Yes

R217 and R630 are right?

Replace R217 and R630.

Done

Yes

Check degaussing connector.

5-1-20 Degaussing Failure

5-1-19 User Control Failure

IC201 Pins 35 and 36 inputs are

right at each function.

Check and replace function key.

Check and replace IC201.

Done

Yes

Check connector Ass’y.

Page 27

5 Troubleshooting

720C/920C 5-13

5-2 General Troubleshooting

5-2-1 No Picture

LED blinks?

LED is green color?

After restart monitor LED doesn't

come on, repair power circuit.

Check signal cable.

Check G2 voltage, high voltage,

R, G, B cathode voltage.

Yes

LED is Amber color?

Yes

5-2-2 Shut down

Yes

5-2-2 Shut Down

Blinking LED’s?

Scan failure

Check horizontal, vertical deflection

system and check power supply

secondary voltages.

Yes

Check power supply.

High voltage failure?

Check high voltage system.

Check and replace IC201.

Done

Yes

Video failure?

Check Video board.

Yes

Page 28

5 Troubleshooting

5-14 720C/920C

5-2-3 Missing Color

Are proper Video levels

on CN101 (D-Sub) Pins 1, 2 and 3?

Are proper AC voltage on all

cathodes?

Refer to 5-1-16 No Video.

Yes

Check signal generator and cathode.

Are proper DC voltage on all

cathodes?

Check IC104 (17”: IC104 Pins 19, 20,

and 21) Pins 10, 11 and 12.

Check QB02, QB03, QG02, QG03

QR02 and QR03.

Change the CRT.

Done

Yes

Is G2 voltage right?

Check G2 wire, G2 control, volume

and FBT.

Yes

Page 29

5 Troubleshooting

720C/920C 5-15

Is G2 voltage right?

Is blank pulse on Pin 27 of IC101

(17”: Pin 23 of IC104) on Video

board?

Check CN102, Q104 (17”: Q103).

Yes

Check G2 control volume and FBT.

Is blank pedestal on

Pins 29, 32 and 35 of IC101

(17”:

25, 28, 30 of IC104)

Check IC101 (17”: IC104) and related

components.

Yes

Is V_FLB pulse on

Pin 17 of IC103 (17”: IC04)?

Check Q301.

Done

Yes

Is blank pedestal on all cathodes?

Check Pins 24, 25 and 26 of IC101

(17”: 19, 20, 21 of IC104)

Check QB02, QB03, QG02, QG03,

QR02 and QR03.

Yes

Check white balance adjustment.

5-2-4 Visible Retrace

Page 30

5 Troubleshooting

5-16 720C/920C

Are signals right?

Signals at Pins 1, 3 and 5 of IC1

are right?

Replace IC1.

Yes

Check Video cable.

Signals at CN201 Pins 6, 9 and

CN102 Pin 6 are right?

Check wire dressing and connections.

Check circuits on Main board.

(IC201 and IC261)

Yes

Done

Check input signals Pins 1, 2

and 3 of D-SUB connector.

5-2-5 Unsynchronized Image

Page 31

5 Troubleshooting

720C/920C 5-17

Is the convergence now

within spec?

Readjust convergence.

Done

Yes

Is the convergence now

within spec?

Done

Change CRT and readjust

convergence.

Done

Yes

Try readjusting convergence.

5-2-6 Misconvergence

Page 32

5 Troubleshooting

5-18 720C/920C

Improved focus?

Check focus leads from FBT

to CRT Socket.

Check the CRT Socket.

Aging monitor and check for focus

change.

Yes

Is dynamic focus circuit right?

Refer to 5-1-15 Dynamic

Focus Failure.

Replace the CRT and verify focus.

Yes

Adjust focus VR.

5-2-7 Poor Focus

5-2-8 Purity Failure

Purity is right?

Degaussing circuit is right?

Refer to 5-1-20 Degaussing Failure.

Replace CRT and verify purity.

Yes

Done

Yes

Degaussing

Page 33

720C/920C 6-1

6-1 720C Exploded View and Parts List

Page 34

720C/920C 6-2

6-2 920C Exploded View and Parts Lists

Page 35

Loc. No Code No. Description Specification Remark

BD261 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, Page 01 BD262 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD265 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD266 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD401 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD402 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD403 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD404 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD501 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD503 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD532 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD601 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD602 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD605 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD630 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD631 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD651 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD663 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BOTTOM 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,-,5mm C201 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C202 2401-000486 C-AL 10uF,20%,50V,GP,TP,6.3x7mm,5 C203 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C204 2201-000247 C-CERAMIC,DISC 0.015nF,5%,50V,NP0,TP,5x3 C206 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C207 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C208 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C209 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C210 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C211 2301-000519 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x3x12.5,5 C212 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C213 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5, C214 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C217 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C218 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C219 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C220 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C221 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C222 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C223 2201-000138 C-CERAMIC,DISC 100pF,10%,50V,Y5P,TP,4.0X C224 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C225 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C226 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C262 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm C263 2202-002149 C-CERAMIC,MLC-RADIAL 0.82NF,2%,50V,NPO,T

7-1-1 Main PCB Parts - 720C

7-1 720C/920C

7-1 720C PCB Parts

Page 36

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

C264 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5 Page 02 C265 2301-000005 C-FILM,PEF 33nF,5%,100V,TP,5.8x12.5x3,5 C266 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C267 2202-002148 C-CERAMIC,MLC-RADIAL 0.68NF,2%,50V,NP0,T C268 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C269 2202-000654 C-CERAMIC,MLC-RADIAL 100nF,10%,50V,X7R,T C270 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 C271 2305-001041 C-FILM,MPEF 220nF,5%,63V,TP,7.5x4.5x13.5 C272 2201-000532 C-CERAMIC,DISC 4.7nF,10%,50V,Y5P,TP,8x3. C273 2301-000005 C-FILM,PEF 33nF,5%,100V,TP,5.8x12.5x3,5 C274 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C275 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C276 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C277 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C278 2401-003473 C-AL 680UF,20%,16V,GP,TP,10X12.5MM,5 C279 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C280 2201-000215 C-CERAMIC,DISC 0.12nF,5%,50V,NP0,TP,8.5x C282 2301-000168 C-FILM,PEF 150nF,5%,100V,TP,11.5x19mm,7. C283 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 C284 2305-000412 C-FILM,MPEF 470nF,5%,63V,TP,-,5mm C285 2401-000597 C-AL 1uF,20%,50V,GP,TP,4x7mm,1.5mm C301 2401-003139 C-AL 1000uF,20%,25V,WT,TP,10*20,5mm C302 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C305 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm, C306 2401-000852 C-AL 220uF,20%,35V,GP,TP,8x11.5mm,5 C307 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm, C308 2305-000237 C-FILM,MPEF 1uF,5%,63V,TP,7.5x15.5mm,5mm C310 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6. C311 2401-000151 C-AL 1000uF,20%,25V,GP,TP,10x20,5 C312 2401-000597 C-AL 1uF,20%,50V,GP,TP,4x7mm,1.5mm C313 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6. C401 2301-000188 C-FILM,PEF 1nF,5%,100V,TP,10.5x12.5x6.5, C402 2401-002264 C-AL 10uF,20%,350V,GP,TP,10x20mm,5m C403 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,-,5mm C406 2401-000049 C-AL 47uF,20%,100V,WT,TP,10x20mm,5m C407 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,7.5x3 C408 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,-,5mm C409 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,-,5mm C410 2301-000020 C-FILM,PEF 27nF,5%,100V,TP,7.3x4x12.5mm, C411 2303-001022 C-FILM,PPF 2nF,5%,2.5KV,TP,23x12x19mm,7. C412 2303-001022 C-FILM,PPF 2nF,5%,2.5KV,TP,23x12x19mm,7. C413 2201-000469 C-CERAMIC,DISC 0.33nF,10%,500V,Y5P,TP,5. C417 2201-000012 C-CERAMIC,DISC 0.22nF,10%,1kV,Y5P,TP,6.3 C418 2301-000519 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x3x12.5,5

7-2 720C/920C

Page 37

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

C419 2201-000131 C-CERAMIC,DISC 0.1nF,10%,2kV,Y5P,TP,6.3x Page 03 C420 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5 C421 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5 C422 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm C423 2202-000561 C-CERAMIC,MLC-RADIAL 680pF,5%,50V,NPO,TP C424 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C425 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C426 2202-000470 C-CERAMIC,MLC-RADIAL 330pF,5%,100V,NPO,5 C427 2303-000011 C-FILM,PPF 1nF,5%,100V,TP,14x11.5mm,7.5m C428 2301-000020 C-FILM,PEF 27nF,5%,100V,TP,7.3x4x12.5mm, C429 2301-000284 C-FILM,PEF 47nF,5%,100V,TP,8.5x12.5mm,5m C430 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C431 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C432 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP, C451 2306-000127 C-FILM,MPPF 120nF,5%,400V,TP,21.5x17mm,5 C452 2306-000127 C-FILM,MPPF 120nF,5%,400V,TP,21.5x17mm,5 C453 2306-000179 C-FILM,MPPF 300nF,5%,250V,TP,20x18.5x10. C454 2306-000234 C-FILM,MPPF 560nF,5%,250V,BK,26x20x13,20 C455 2306-000147 C-FILM,MPPF 1uF,5%,250V,BK,26x24x15,22.5 C456 2306-000131 C-FILM,MPPF 150nF,5%,250V,TP,19x16x7.5,7 C457 2306-001011 C-FILM,MPPF 56nF,5%,250V,TP,19x7.5x14.5, C459 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C501 2301-001027 C-FILM,PEF 15nF,10%,250V,TP,9.5x12x4.5,5 C502 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C503 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C504 2401-001576 C-AL 47uF,20%,50V,GP,TP,8x11.5,5 C505 2401-000037 C-AL 470uF,20%,16V,GP,TP,8x11.5,5 C521 2301-000294 C-FILM,PEF 56nF,5%,100V,TP,9.5x12.5mm,5m C522 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm C523 2401-000292 C-AL 100uF,20%,16V,WT,TP,8x11.5mm,5 C524 2201-000163 C-CERAMIC,DISC 10nF,+80-20%,50V,Y5V,TP,7 C525 2305-001041 C-FILM,MPEF 220nF,5%,63V,TP,7.5x4.5x13.5 C526 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C527 2401-000971 C-AL 22uF,20%,50V,WT,TP,6x11mm,5mm C528 2401-001576 C-AL 47uF,20%,50V,GP,TP,8x11.5,5 C530 2201-000469 C-CERAMIC,DISC 0.33nF,10%,500V,Y5P,TP,5. C531 2303-000147 C-FILM,PPF 1NF,5%,2KV,TP,23X13X8MM,7.5 C532 2401-000638 C-AL 2.2uF,20%,350V,WT,TP,10x12.5mm C533 2201-000732 C-CERAMIC,DISC 0.68nF,10%,1kV,Y5P,TP,7x4 C534 2401-001576 C-AL 47uF,20%,50V,GP,TP,8x11.5,5 C535 2401-000771 C-AL 220uF,20%,100V,WT,TP,16x25,7.5 C536 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C537 2401-000638 C-AL 2.2uF,20%,350V,WT,TP,10x12.5mm C538 2305-000665 C-FILM,MPEF 100nF,5%,63V,TP,7.5x4.0x5.0m

7-3 720C/920C

Page 38

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

C539 2401-000649 C-AL 2.2uF,20%,50V,BP,TP,5x11,5 Page 04 C540 2201-000732 C-CERAMIC,DISC 0.68nF,10%,1kV,Y5P,TP,7x4 C551 2401-000043 C-AL 1uF,20%,160V,GP,TP,6.3x11,5 C552 2305-000004 C-FILM,MPEF 220nF,10%,100V,TP,12.7x16,5m C555 2305-000004 C-FILM,MPEF 220nF,10%,100V,TP,12.7x16,5m C556 2201-000285 C-CERAMIC,DISC 1nF,10%,1kV,Y5P,TP,8x5,5 C557 2201-000012 C-CERAMIC,DISC 0.22nF,10%,1kV,Y5P,TP,6.3 C558 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C603 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP, C604 2301-001285 C-FILM,MPPF 680NF,10%,275V,BK,31X11X21MM C605 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C606 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C607 2401-000015 C-AL 33uF,20%,50V,WT,-,6.3x11mm,2.5 C608 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C609 2401-003483 C-AL 270uF,20%,400V,GP,BK,25.4x45,10 C610 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP, C611 2201-000012 C-CERAMIC,DISC 0.22nF,10%,1kV,Y5P,TP,6.3 C612 2201-000129 C-CERAMIC,DISC 0.1nF,10%,1kV,Y5P,TP,7x4, C614 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm C615 2301-000168 C-FILM,PEF 150nF,5%,100V,TP,11.5x19mm,7. C616 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C617 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm, C633 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2. C634 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C635 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C636 2401-003497 C-AL 100uF,20%,160V,WT,TP,12.5x25mm,5 C638 2401-003496 C-AL 47uF,20%,350V,WT,TP,16x25mm,7.5 C639 2401-000038 C-AL 470uF,20%,25V,GP,TP,10x12.5mm, C640 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5 C641 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6. C642 2401-000317 C-AL 100uF,20%,25V,WT,TP,8x11.5,5 C643 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5 C644 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C645 2401-001422 C-AL 470uF,20%,35V,WT,TP,12.5x25,5 C647 2301-000174 C-FILM,PEF 15nF,5%,100V,TP,7.2x4.0x7.5mm C648 2301-000004 C-FILM,PEF 2.2nF,5%,100V,TP,5.5X10X2.9,5 C649 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP, C652 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm C653 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C654 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C656 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C661 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C662 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2. C663 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5

7-4 720C/920C

Page 39

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

C664 2201-000129 C-CERAMIC,DISC 0.1nF,10%,1kV,Y5P,TP,7x4, Page 05 C665 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm, C666 2401-000913 C-AL 22uF,20%,16V,GP,TP,5x11mm,2.5m C667 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C668 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP, CIS 3301-001264 CORE-FERRITE AC,18.2X9.7X28.2MM,1500,280 CIS BH39-00059A CBF-HARNESS 3P/3P,420MM,GRY,UL2547,AWG26 CIS BH39-00060A CBF-HARNESS 15P/15P,180MM,WHT/BLU/RED/BL CIS BH39-00124A CBFSIGNAL ATT,1830MM,15P/06,08,-,-,D-SUB CIS BH39-40306C CBF-HARNESS 60MM,BLK,1015,AWG22,-,-,-,CN204 3711-004352 CONNECTOR-HEADER BOX,15P,1R,2MM,STRAIGHT CN208 3711-003843 CONNECTOR-HEADER BOX,8P,1R,2mm,STRAIGHT, CN211 3711-004349 CONNECTOR-HEADER BOX,3P,1R,2MM,STRAIGHT, CN212 3711-004349 CONNECTOR-HEADER BOX,3P,1R,2MM,STRAIGHT, CN401 3711-003989 CONNECTOR-HEADER NOWALL,4P,1R,8mm,STRAIG CN409 3711-000197 CONNECTOR-HEADER 1WALL,3P,1R,2.5mm,STRAI D201 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D202 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D203 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D262 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D264 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D301 0402-000272 DIODE-RECTIFIER UF4001,50V,1A,DO-41,TP D302 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D401 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D402 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D403 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D405 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D406 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D407 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D408 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D409 0402-000208 DIODE-RECTIFIER EK-04,40V,1.5A,DO-41 D410 0402-001215 DIODE-RECTIFIER SDS10U150S,1.5KV,10A,TOD411 0402-000007 DIODE-RECTIFIER 1N4937GP,600V,1A,DO-41,T D412 0402-000007 DIODE-RECTIFIER 1N4937GP,600V,1A,DO-41,T D413 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP D414 0402-000272 DIODE-RECTIFIER UF4001,50V,1A,DO-41,TP D415 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T D416 0402-000454 DIODE-RECTIFIER RG10V1,400V,1.2A,DO-201 D451 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D501 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T D502 0402-001114 DIODE-RECTIFIER 1N4936GP,400V,1A,DO-204A D503 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D504 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D506 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35,

7-5 720C/920C

Page 40

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

D521 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, Page 06 D522 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D523 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D524 0402-001295 DIODE-RECTIFIER GUR460L-5700,600V,4A,DOD525 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D526 0402-001295 DIODE-RECTIFIER GUR460L-5700,600V,4A,DOD527 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP D528 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D529 0402-000007 DIODE-RECTIFIER 1N4937GP,600V,1A,DO-41,T D530 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D551 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D552 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D553 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D554 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D601 0402-001227 DIODE-BRIDGE D3SBA60,600V,2.3A,SIP-4,BK D604 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T D605 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP D606 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D607 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP D630 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D632 0402-001289 DIODE-RECTIFIER 31DF6,600V,3A,DO-201AD,B D633 0402-000250 DIODE-RECTIFIER RG4C,1000V,1A,D634 0402-001190 DIODE-RECTIFIER RG10Z,200V,1.2A,DO-15,TP D635 0402-001118 DIODE-RECTIFIER UF1G,400V,1.2A,DO-204AL, D636 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D637 0402-000016 DIODE-RECTIFIER UF5404,400V,3A,DO-201AD, D638 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D639 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D661 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D662 0402-000126 DIODE-RECTIFIER 1N4001GP,50V,1A,DO-41,TP D663 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T F633 3601-001092 FUSE-AXIALLEAD 125V,2.5A,SLOW-BLOW,EPOXY FG601 3601-000455 FUSE-CARTRIDGE 250V,4A,TIME-LAG,CERAMIC, FH601 3602-000001 FUSE-CLIP -,-,30mohm IC201 0903-001166 IC-MICROCONTROLLER 88P6232,8BIT,DIP,42P, IC202 1203-000495 IC-RESET 7045,T0-92,3P,-,PLASTIC,4.3/4. IC203 1103-001150 IC-EEPROM 24C081,8KBIT,DIP,8P,300MIL,10M IC204 1103-001087 IC-EEPROM 24LC21,128x8BIT,DIP,8P,300MIL, IC261 1204-001448 IC-DEF.PROCESSOR SAM9222G,DIP,32P,300MI IC301 1204-001508 IC-VERTICALDEF. KA2142,SIP,10P,-,PLASTIC IC402 1203-001099 IC-PWMCONTROLLER 3843,DIP,8P,250MIL,PLAS IC403 BH13-00009A IC-H/VCONVERGENCE PG17/19,AN5452,SIP,12P IC501 1203-000610 IC-PWMCONTROLLER 494,DIP,16P,300MIL,PLAS IC502 1201-000420 IC-OPAMP 358,DIP,8P,300MIL,DUAL,100V/mV

7-6 720C/920C

Page 41

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

IC601 BH13-00012A IC-POWERSWITCH PG17/19/21,DP308O,TO-3P-5 Page 07 IC602 0604-001018 PHOTO-COUPLER DAR-TR,63-125%,200mW,DIP-4 IC604 1203-000002 IC-POSI.ADJUSTREG. 431,TO-92,3P,-,PLAST IC605 1203-000165 IC-POSI.ADJUSTREG. 78R12,TO-220,3P,-,-,1 IC606 1203-000001 IC-POSI.FIXEDREG. 7805,TO-220,3P,-,PLAST IC661 0604-001018 PHOTO-COUPLER DAR-TR,63-125%,200mW,DIP-4 IC662 BH13-00010A IC-POWERSWITCH S-III,TNY254P,DIP,8P,POWE JP495 2004-001298 R-METAL 82Kohm,2%,1/4W,AA,TP,2.4x6.4mm L260 2701-000154 INDUCTOR-AXIAL 220uH,10%,4.2x9.8mm L401 2701-000187 INDUCTOR-AXIAL 4.7uH,10%,4.2x9.8mm L402 BH27-20345J COIL-HORIZ.CENTER 3.5mH,-,OB6*30-1HHA,BU L403 BH26-00001A TRANS-H.LINEARITY 5.0UH/47.5MH,5P,DR1420 L404 2701-000179 INDUCTOR-AXIAL 33uH,10%,4.2x9.8mm L406 2701-000128 INDUCTOR-AXIAL 15uH,10%,4.2x9.8mm L501 2701-000179 INDUCTOR-AXIAL 33uH,10%,4.2x9.8mm L503 2701-000187 INDUCTOR-AXIAL 4.7uH,10%,4.2x9.8mm L521 BH27-00018A COIL-CHOKE 6.8UH,-,DR08*11,BULK,+/-10%,L601 BH27-00025A COIL-LINEFILTER 24.0MH,-,SQE-2828,BK,-,LC601 2901-001161 FILTER-EMIACLINE 250V,3A,UL/CSA/SEMKO,22 OP1 0601-000334 LED CBI-ANGLE,GRN/YEL,4.8MM PCB BH41-00027A P.C.B-MAIN PG,FR1,-,247*330,1.6T POS601 1404-000002 THERMISTOR-PTC 9ohm,20%,-,-,TR,RECT,Q261 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q262 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP Q263 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q264 0505-000013 FET-SILICON VN2222LL,N,60V,150mA,7.5ohm, Q290 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q301 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q401 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP Q403 0505-001130 FET-SILICON IRF740A,N,400V,10uA,550mohm, Q404 0505-001357 FET-SILICON SKS4N20,N,200V,3A,1.3OHM,27W Q405 0502-001143 TR-POWER 2SC5583,NPN,150W,TOP-3L,ST,6-1 Q451 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q452 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q453 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q454 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q455 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q456 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM Q457 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM Q458 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM Q459 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM Q460 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM Q501 0501-000143 TR-SMALLSIGNAL 2N6520,PNP,625mW,TO-92,-, Q521 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP

7-7 720C/920C

Page 42

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

Q522 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Page 08 Q523 0501-000581 TR-SMALLSIGNAL 2N3906,PNP,625mW,TO-92,TP Q524 0505-001266 FET-SILICON 2SK2761-01MR,N,600V,10A,0.85 Q551 0502-000348 TR-POWER TIP29C,NPN,2W,TO-220,-,15-75 Q552 0502-000351 TR-POWER TIP30,PNP,2W,TO-220AB,-,15-75 Q553 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92,-, Q554 0501-000413 TR-SMALLSIGNAL KSP44,NPN,625mW,TO-92,-,5 Q630 0501-000010 TR-SMALLSIGNAL KSC1008,NPN,800mW,TO-92,T Q632 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q663 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q664 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP R201 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R202 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R203 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R204 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R205 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R206 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R207 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R208 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM R209 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM R211 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R212 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R214 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM R215 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R216 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R217 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R218 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R219 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R220 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R221 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R223 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R224 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R225 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R226 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R229 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R230 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R231 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R232 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R233 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R234 2004-000344 R-METAL 15Kohm,1%,1/4W,AA,TP,2.4x6.4mm R235 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R236 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R237 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R238 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM

7-8 720C/920C

Page 43

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

R239 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM Page 09 R240 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R241 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R242 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R243 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R244 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R245 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM R246 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM R247 2001-000435 R-CARBON 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM R261 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R262 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R263 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R264 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R265 2001-001015 R-CARBON 9.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R266 2001-000744 R-CARBON 4.7OHM,5%,1/8W,AA,TP,1.8X3.2MM R267 2004-001118 R-METAL 5Kohm,1%,1/4W,AA,TP,2.4x6.4mm R268 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R269 2001-003190 R-CARBON 2.5MOHM,5%,1/8W,AA,TP,1.8X3.2MM R270 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R271 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R272 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM R273 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM R274 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R275 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R276 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R277 2001-000009 R-CARBON 20KOHM,5%,1/8W,AA,TP,1.8X3.2MM R278 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R279 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R280 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R281 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R282 2001-000319 R-CARBON 120KOHM,5%,1/8W,AA,TP,1.8X3.2MM R283 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R284 2004-004367 R-METAL 90Kohm,1%,1/4W,AA,TP,6.2x2.6mm R285 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R286 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R287 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R288 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R289 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R290 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R291 2001-000007 R-CARBON 3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R292 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM R293 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R294 2001-000007 R-CARBON 3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R295 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM

7-9 720C/920C

Page 44

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

R296 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM Page 10 R297 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R298 2003-000669 R-METALOXIDE(S) 390ohm,5%,1W,AA,TP,3.3x9 R299 2001-001107 R-CARBON(S) 220ohm,5%,1/2W,AA,TP,2.4x6.4 R301 2004-000532 R-METAL 20Kohm,1%,1/4W,AA,TP,2.4x6.4mm R302 2004-001661 R-METAL 3Kohm,1%,1/4W,AA,TP,2.4x6.4mm R303 2004-000268 R-METAL 120ohm,1%,1/4W,AA,TP,2.4x6.4mm R304 2004-000344 R-METAL 15Kohm,1%,1/4W,AA,TP,2.4x6.4mm R305 2004-001136 R-METAL 6.8Kohm,1%,1/4W,AA,TP,2.4x6.4m R306 2005-001064 R-WIREWOUND 0.9OHM,5%,2W,AA,TP,3.8X11MM R307 2001-001088 R-CARBON(S) 1KOHM,5%,1/2W,AA,TP,2.4X6.4M R309 2001-000016 R-CARBON(S) 1OHM,5%,1/2W,AA,TP,2.4X6.4MM R310 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R311 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R312 2001-000977 R-CARBON 8.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R313 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R314 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R315 2008-000114 R-FUSIBLE 1.2ohm,5%,1/2W,AA,TP,3.5x9.4mm R316 2008-000114 R-FUSIBLE 1.2ohm,5%,1/2W,AA,TP,3.5x9.4mm R401 2001-000017 R-CARBON 4.7OHM,5%,1/4W,AA,TP,2.4X6.4MM R402 2001-000645 R-CARBON 330KOHM,5%,1/8W,AA,TP,1.8X3.2MM R403 2001-000011 R-CARBON 75KOHM,5%,1/8W,AA,TP,1.8X3.2MM R404 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM R405 2003-000763 R-METALOXIDE(S) 6.8ohm,5%,3W,AA,TP,6x16m R406 2001-000006 R-CARBON 2.4KOHM,5%,1/8W,AA,TP,1.8X3.2MM R407 2001-000958 R-CARBON 750OHM,5%,1/8W,AA,TP,1.8X3.2MM R408 2001-000011 R-CARBON 75KOHM,5%,1/8W,AA,TP,1.8X3.2MM R409 2001-000037 R-CARBON(S) 330OHM,5%,1/2W,AA,TP,2.4X6.4 R410 2003-000557 R-METALOXIDE(S) 2.2ohm,5%,3W,AA,TP,6x16m R411 2003-000747 R-METALOXIDE(S) 56ohm,5%,3W,AA,TP,6x16mm R412 2003-000747 R-METALOXIDE(S) 56ohm,5%,3W,AA,TP,6x16mm R413 2001-000539 R-CARBON 24KOHM,5%,1/8W,AA,TP,1.8X3.2MM R414 2004-000284 R-METAL 12Kohm,1%,1/4W,AA,TP,2.4x6.4mm R415 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM R416 2001-001163 R-CARBON(S) 560OHM,5%,1/2W,AA,TP,2.4X6.4 R417 2004-000216 R-METAL 10Kohm,1%,1/4W,AA,TP,2.4x6.4mm R418 2003-000473 R-METALOXIDE(S) 10ohm,5%,3W,AA,TP,6x16mm R419 2001-000019 R-CARBON(S) 10OHM,5%,1/2W,AA,TP,2.4X6.4M R420 2003-000578 R-METALOXIDE(S) 220ohm,5%,2W,AA,TP,4x12m R421 2003-000653 R-METALOXIDE(S) 330ohm,5%,3W,AA,TP,6x16m R422 2001-000028 R-CARBON(S) 100OHM,5%,1/2W,AA,TP,2.4X6.4 R423 2001-000028 R-CARBON(S) 100OHM,5%,1/2W,AA,TP,2.4X6.4 R424 2001-000947 R-CARBON 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM R429 2003-000423 R-METALOXIDE(S) 1.2ohm,5%,3W,AA,TP,6x16m

7-10 720C/920C

Page 45

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

R432 2004-004038 R-METAL 4.3Kohm,1%,1/4W,AA,TP,2.4x6.4m Page 11 R433 2004-000532 R-METAL 20Kohm,1%,1/4W,AA,TP,2.4x6.4mm R434 2001-001187 R-CARBON(S) 75OHM,5%,1/2W,AA,TP,2.4X6.4M R435 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM R436 2008-000147 R-FUSIBLE 22ohm,5%,1/4W,AA,TP,2.6x6.7mm R437 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM R438 2008-000140 R-FUSIBLE 2.2ohm,5%,1/2W,AA,TP,3.5x9.4mm R451 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R452 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R453 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R454 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R455 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R456 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R457 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R458 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R459 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R460 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R461 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R462 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R463 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R464 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R465 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R466 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R467 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R468 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R469 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R470 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R471 2003-000450 R-METALOXIDE(S) 100Kohm,5%,3W,AA,TP,6x16 R476 2001-000022 R-CARBON(S) 33OHM,5%,1/2W,AA,TP,2.4X6.4M R477 2001-000022 R-CARBON(S) 33OHM,5%,1/2W,AA,TP,2.4X6.4M R501 2004-001349 R-METAL 91Kohm,1%,1/4W,AA,TP,2.4x6.4mm R502 2004-000327 R-METAL 150Kohm,1%,1/4W,AA,TP,2.4x6.4m R503 2001-000096 R-CARBON(S) 1MOHM,5%,1/2W,AA,TP,2.4X6.4M R504 2001-000546 R-CARBON 270KOHM,5%,1/4W,AA,TP,2.4X6.4MM R506 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM R507 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R508 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM R509 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R510 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM R511 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R512 2004-000861 R-METAL 39Kohm,1%,1/4W,AA,TP,2.4x6.4mm R513 2004-000515 R-METAL 200Kohm,1%,1/4W,AA,TP,2.4x6.4m R521 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM R523 2001-000947 R-CARBON 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM

7-11 720C/920C

Page 46

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

R524 2001-000689 R-CARBON 390KOHM,5%,1/8W,AA,TP,1.8X3.2MM Page 12 R525 2001-000977 R-CARBON 8.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R526 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM R527 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R528 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM R529 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R530 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R532 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R533 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM R534 2001-000018 R-CARBON 6.8OHM,5%,1/4W,AA,TP,2.4X6.4MM R535 2005-000210 R-WIREWOUND 0.33ohm,5%,1W,AC,BK,4.5x11mm R536 2003-000014 R-METALOXIDE(S) 10Kohm,5%,3W,AA,TP,6x16m R537 2003-000014 R-METALOXIDE(S) 10Kohm,5%,3W,AA,TP,6x16m R538 2001-000073 R-CARBON 33KOHM,5%,1/4W,AA,TP,2.4X6.4MM R539 2006-001066 R-CEMENT 33OHM,5%,7W,CS,BK,9X10X54MM R540 2004-001349 R-METAL 91Kohm,1%,1/4W,AA,TP,2.4x6.4mm R543 2001-000878 R-CARBON 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R549 2003-000462 R-METALOXIDE(S) 10Kohm,5%,2W,AA,TP,4x12m R551 2003-000006 R-METALOXIDE 47ohm,5%,1W,AA,TP,4.3x12mm R552 2001-000066 R-CARBON(S) 10KOHM,5%,1/2W,AA,TP,2.4X6.4 R553 2001-001153 R-CARBON(S) 47OHM,5%,1/2W,AA,TP,2.4X6.4M R554 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R555 2001-000319 R-CARBON 120KOHM,5%,1/8W,AA,TP,1.8X3.2MM R556 2001-000045 R-CARBON 1.8KOHM,5%,1/4W,AA,TP,2.4X6.4MM R558 2003-000462 R-METALOXIDE(S) 10Kohm,5%,2W,AA,TP,4x12m R560 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM R561 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM R562 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM R563 2001-001186 R-CARBON(S) 75KOHM,5%,1/2W,AA,TP,2.4X6.4 R564 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6. R565 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6. R566 2001-001186 R-CARBON(S) 75KOHM,5%,1/2W,AA,TP,2.4X6.4 R570 BH39-40305U CBF-HARNESS Jumper wire 50mm R601 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM R603 2001-000044 R-CARBON 1.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM R604 2001-000087 R-CARBON(S) 120KOHM,5%,1/2W,AA,TP,2.4X6. R605 2001-000085 R-CARBON(S) 100KOHM,5%,1/2W,AA,TP,2.4X6. R607 2001-000376 R-CARBON 15OHM,5%,1/8W,AA,TP,1.8X3.2MM R608 2003-000756 R-METALOXIDE(S) 6.8Kohm,5%,3W,AA,TP,6x16 R609 2001-000552 R-CARBON 270OHM,5%,1/4W,AA,TP,2.4X6.4MM R611 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM R630 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R631 2001-000023 R-CARBON 47OHM,5%,1/4W,AA,TP,2.4X6.4MM R632 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm

7-12 720C/920C

Page 47

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

R633 2001-001106 R-CARBON(S) 220KOHM,5%,1/2W,AA,TP,2.4X6. Page 13 R634 2001-001131 R-CARBON(S) 33KOHM,5%,1/2W,AA,TP,2.4X6.4 R635 2001-001106 R-CARBON(S) 220KOHM,5%,1/2W,AA,TP,2.4X6. R636 2001-000263 R-CARBON 1.8OHM,5%,1/2W,AA,TP,3.3X9MM R637 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R638 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R639 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM R640 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R641 2001-000034 R-CARBON 220OHM,5%,1/4W,AA,TP,2.4X6.4MM R642 2001-000508 R-CARBON 220KOHM,5%,1/8W,AA,TP,1.8X3.2MM R643 2003-000521 R-METALOXIDE(S) 180Kohm,5%,1W,AA,TP,3.3x R644 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM R645 2004-000679 R-METAL 2Kohm,1%,1/4W,AA,TP,2.4x6.4mm R646 2004-000334 R-METAL 150ohm,1%,1/4W,AA,TP,2.4x6.4mm R648 2001-001106 R-CARBON(S) 220KOHM,5%,1/2W,AA,TP,2.4X6. R651 2001-001138 R-CARBON(S) 390OHM,5%,1/2W,AA,TP,2.4X6.4 R657 2001-000495 R-CARBON 20KOHM,5%,1/4W,AA,TP,2.4X6.4MM R661 2001-001050 R-CARBON(S) 1.5KOHM,5%,1/2W,AA,TP,2.4X6. R662 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R663 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM R664 2001-000495 R-CARBON 20KOHM,5%,1/4W,AA,TP,2.4X6.4MM R665 2004-000964 R-METAL 470Kohm,1%,1/4W,AA,TP,2.4x6.4m R666 2004-000964 R-METAL 470Kohm,1%,1/4W,AA,TP,2.4x6.4m R667 2004-001211 R-METAL 7.5Kohm,1%,1/4W,AA,TP,2.4x6.4m R668 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R669 2001-000793 R-CARBON 47OHM,5%,1/8W,AA,TP,1.8X3.2MM RL601 3501-001111 RELAY-POWER 12Vdc,250mW,5A,1FormA,15mS,5 SK521 4715-000001 SURGEABSORBER 1KV,+50-10%,-,-, SW1 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP SW2 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP SW3 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP SW4 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP SW5 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP SW6 3403-001075 SWITCH-PUSH 30Vdc,300mA,DPDT,OFF-ON-OFF, SW7 3404-001079 SWITCH-TACT 12VDC,50MA,160GF,8.4X15.55X2 T401 BH26-00041A TRANS-HOR.DRIVE 2.7MH,8P,EI-2519,PL3,-,T402 BH26-00040A TRANS-HOR.PULSE 1.5MH,10P,EI-3026,PL3,-, T403 BH26-00002A TRANS-H.GATE 520UH,5P,EI-1614,SB-5S,520U T501 BH26-00051A TRANS-FBT 80.4UH,14P,HV22UR,HV22U,-,-,FE T502 BH26-00056A TRANS-FOCUS 3.8MHMIN,10P,SB-5S,EI-2218,S T601 BH26-00039A TRANS-POWER 150UH,18P,EER4042,PL3,-,6.0U T602 BH26-30302S TRANS-SYNC. 3-1(250UH),-,-,SB-5S,UU1116, T661 BH26-00042A TRANS 2.5MH,8P,EI-1916,PL3,-,150UH,TH601 1404-001076 THERMISTOR-NTC 8ohm,15%,-,17mW/C,TP

7-13 720C/920C

Page 48

Loc. No Code No. Description Specification Remark

Main PCB Parts - 720C

VR401 2103-001049 VR-SEMI 100ohm,30%,1/5W,SIDE Page 14 VR501 2103-001080 VR-SEMI 100KOHM,25%,0.3W,SIDE X201 2801-000006 CRYSTAL-UNIT 12MHz,50ppm,28-AAM,S,35ohm, ZD241 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD242 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD243 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD245 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD246 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD247 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD248 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD249 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD250 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD252 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD260 0403-000509 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500 ZD501 0403-000355 DIODE-ZENER UZ5.1BSB,5.1V,4.97-5.18V,500 ZD601 0403-000753 DIODE-ZENER MTZJ27D,27V,26.29-27.64V,500 ZD602 0403-001068 DIODE-ZENER UZ4.7BSA,4.7V,4.47-4.65V,500 ZD661 0403-000367 DIODE-ZENER UZ7.5BSC,7.5V,7.33-7.64V,500

7-14 720C/920C

Page 49

Loc. No Code No. Description Specification Remark

BD102 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, Page 01 BD161 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD165 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD181 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD185 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, C101 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5 C103 2401-000597 C-AL 1uF,20%,50V,GP,TP,4x7mm,1.5mm C104 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5 C105 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C106 2401-003224 C-AL 470uF,20%,16V,WT,TP,8X11.5,5mm C107 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C108 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C109 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C110 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C111 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C112 2401-000814 C-AL 220uF,20%,16V,WT,TP,10x12.5,5 C113 2401-001459 C-AL 47uF,20%,100V,GP,TP,10x16.5,5 C114 2401-000393 C-AL 10uF,20%,100V,WT,TP,8x11.5,5 C115 2202-000319 C-CERAMIC,MLC-RADIAL 100nF,10%,100V,X7R, C116 2201-000234 C-CERAMIC,DISC 0.15nF,5%,50V,NP0,TP,9x3, C117 2201-000234 C-CERAMIC,DISC 0.15nF,5%,50V,NP0,TP,9x3, C118 2305-000237 C-FILM,MPEF 1uF,5%,63V,TP,7.5x15.5mm,5mm C120 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C121 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C122 2202-000669 C-CERAMIC,MLC-RADIAL 10nF,10%,50V,X7R,TP C123 2202-000669 C-CERAMIC,MLC-RADIAL 10nF,10%,50V,X7R,TP C124 2401-000443 C-AL 10uF,20%,25V,GP,TP,5x5mm,2mm C126 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5 C127 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C128 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C129 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm C131 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6. C141 2201-000764 C-CERAMIC,DISC 0.082nF,5%,50V,NP0,TP,8x3 C142 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C150 2201-000341 C-CERAMIC,DISC 2.7nF,10%,2kV,Y5P,TP,14x6 C151 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C152 2201-000530 C-CERAMIC,DISC 4.7nF,10%,500V,Y5P,TP,12. C190 2401-000393 C-AL 10uF,20%,100V,WT,TP,8x11.5,5 C801 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C802 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C803 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CB01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CB04 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CB05 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5

7-1-2 Video PCB Parts - 720C

7-15 720C/920C

Page 50

Loc. No Code No. Description Specification Remark

Video PCB Parts - 720C

CB14 2401-000055 C-AL 1uF,20%,160V,WT,TP,3x11,5mm Page 02 CB16 2401-001318 C-AL 470nF,20%,100V,GP,TP,5x11,5 CB17 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5 CG01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CG04 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CG14 2401-000055 C-AL 1uF,20%,160V,WT,TP,3x11,5mm CG16 2401-001318 C-AL 470nF,20%,100V,GP,TP,5x11,5 CG17 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5 CN101 3711-004228 CONNECTOR-HEADER BOX,6P,1R,2MM,ANGLE,SN CN102 3711-004123 CONNECTOR-HEADER BOX,15P,1R,2mm,ANGLE,SN CR01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CR04 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CR05 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CR14 2401-000055 C-AL 1uF,20%,160V,WT,TP,3x11,5mm CR16 2401-003479 C-AL 0.47UF,20%,100V,WT,TP,5X11MM,5 CR17 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5 D101 0403-000509 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500 D102 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D103 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DB01 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DB02 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DB03 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DB04 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DB05 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DG01 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DG02 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DG03 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DG04 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DG05 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DR01 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DR02 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DR03 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DR04 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DR05 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, IC04 1204-001547 IC-OSDPROCESSOR KS2501B-10,DIP,24P,300MI IC104 1201-001409 IC-VIDEOAMP 2506,DIP,28P,600MIL,SINGLE, IC105 BH13-00011A IC-CRTDRIVER PG17/19/21,LM2402,TO-220-11 JP231 BH39-40305U CBF-HARNESS ,52MM,,,AWG22(0.6PI),,,,,, L181 2701-000125 INDUCTOR-AXIAL 150uH,10%,3x7mm LB03 2701-001065 INDUCTOR-AXIAL 0.22UH,10%,3X7MM LG03 2701-001065 INDUCTOR-AXIAL 0.22UH,10%,3X7MM LR03 2701-001065 INDUCTOR-AXIAL 0.22UH,10%,3X7MM PCB BH41-00026A PCB-VIDEO PG17HS,FR1,1,247*330,Q101 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP

7-16 720C/920C

Page 51

Loc. No Code No. Description Specification Remark

Video PCB Parts - 720C

Q102 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Page 03 Q103 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q141 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP QB01 0501-000621 TR-SMALLSIGNAL 2N5770,NPN,450mW,TO-92,TP QB02 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92,-, QB03 0501-000138 TR-SMALLSIGNAL 2N5401,PNP,625mW,TO-92,TP QG01 0501-000621 TR-SMALLSIGNAL 2N5770,NPN,450mW,TO-92,TP QG02 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92,-, QG03 0501-000138 TR-SMALLSIGNAL 2N5401,PNP,625mW,TO-92,TP QR01 0501-000621 TR-SMALLSIGNAL 2N5770,NPN,450mW,TO-92,TP QR02 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92,-, QR03 0501-000138 TR-SMALLSIGNAL 2N5401,PNP,625mW,TO-92,TP R101 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R102 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R103 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R104 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R105 2001-000539 R-CARBON 24KOHM,5%,1/8W,AA,TP,1.8X3.2MM R106 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R108 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R109 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R110 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R111 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R112 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R114 2001-000016 R-CARBON(S) 1OHM,5%,1/2W,AA,TP,2.4X6.4MM R115 2001-000793 R-CARBON 47OHM,5%,1/8W,AA,TP,1.8X3.2MM R116 2002-001022 R-COMPOSITION 30MOHM,5%,1/4W,AA,TP,2.5X6 R118 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R123 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM R131 2001-001107 R-CARBON(S) 220ohm,5%,1/2W,AA,TP,2.4x6.4 R141 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R142 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R143 2001-000995 R-CARBON 820OHM,5%,1/8W,AA,TP,1.8X3.2MM R161 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R162 2001-000633 R-CARBON 30KOHM,5%,1/8W,AA,TP,1.8X3.2MM R163 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R164 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R165 2001-000878 R-CARBON 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R166 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R168 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R169 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R801 2001-000019 R-CARBON(S) 10OHM,5%,1/2W,AA,TP,2.4X6.4M R802 2001-000019 R-CARBON(S) 10OHM,5%,1/2W,AA,TP,2.4X6.4M R805 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R806 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM

7-17 720C/920C

Page 52

Loc. No Code No. Description Specification Remark

Video PCB Parts - 720C

RB01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM Page 04 RB02 2001-000527 R-CARBON 22OHM,5%,1/8W,AA,TP,1.8X3.2MM RB04 2001-000005 R-CARBON 390ohm,5%,1/8W,AA,TP,1.8x3.2mm RB05 2001-000325 R-CARBON 120OHM,5%,1/8W,AA,TP,1.8X3.2MM RB06 2001-000302 R-CARBON 10OHM,5%,1/8W,AA,TP,1.8X3.2MM RB07 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM RB13 2001-000047 R-CARBON 2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM RB14 2001-000084 R-CARBON 100KOHM,5%,1/4W,AA,TP,2.4X6.4MM RB16 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM RB17 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4M RB31 2001-000488 R-CARBON 200OHM,5%,1/4W,AA,TP,2.4X6.4MM RG01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM RG02 2001-000527 R-CARBON 22OHM,5%,1/8W,AA,TP,1.8X3.2MM RG04 2001-000005 R-CARBON 390ohm,5%,1/8W,AA,TP,1.8x3.2mm RG05 2001-000325 R-CARBON 120OHM,5%,1/8W,AA,TP,1.8X3.2MM RG06 2001-000302 R-CARBON 10OHM,5%,1/8W,AA,TP,1.8X3.2MM RG07 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM RG13 2001-000047 R-CARBON 2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM RG14 2001-000084 R-CARBON 100KOHM,5%,1/4W,AA,TP,2.4X6.4MM RG16 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM RG17 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4M RG31 2001-000488 R-CARBON 200OHM,5%,1/4W,AA,TP,2.4X6.4MM RR01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM RR02 2001-000527 R-CARBON 22OHM,5%,1/8W,AA,TP,1.8X3.2MM RR04 2001-000005 R-CARBON 390ohm,5%,1/8W,AA,TP,1.8x3.2mm RR05 2001-000325 R-CARBON 120OHM,5%,1/8W,AA,TP,1.8X3.2MM RR06 2001-000302 R-CARBON 10OHM,5%,1/8W,AA,TP,1.8X3.2MM RR07 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM RR13 2001-000047 R-CARBON 2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM RR14 2001-000084 R-CARBON 100KOHM,5%,1/4W,AA,TP,2.4X6.4MM RR16 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM RR17 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4M RR31 2001-000488 R-CARBON 200OHM,5%,1/4W,AA,TP,2.4X6.4MM SK101 4715-000102 SURGEABSORBER 200V,20%,1000A,-,RADIAL SK102 4715-000102 SURGEABSORBER 200V,20%,1000A,-,RADIAL SK103 4715-000102 SURGEABSORBER 200V,20%,1000A,-,RADIAL SK104 4715-000106 SURGEABSORBER 300V,210-390V,-,-,AXIAL SK105 3704-001116 SOCKET-CRT 11P,22.5PI,26.5PI,NI,SK107 4715-000001 SURGEABSORBER 1KV,+50-10%,-,-,

7-18 720C/920C

Page 53

Loc. No Code No. Description Specification Remark

HC01 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V HC02 2202-000841 C-CERAMIC,MLC-RADIAL 33nF,10%,100V,X7R,T HC03 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 HCN01 3711-002702 CONNECTOR-HEADER NOWALL,4P,1R,2.5mm,ANGL HD01 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, HIC01 1202-000119 IC-VOLTAGECOMP. 319,DIP,14P,300MIL,DUAL, HR01 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM HR02 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM HR03 2001-000325 R-CARBON 120OHM,5%,1/8W,AA,TP,1.8X3.2MM HR04 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM HR05 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM HR06 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM HR07 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM PCB BH41-00036A P.C.B-SUB PG17HO,FR1,-,247*330,1.6T

7-1-3 SOG PCB Parts - 720C

7-19 720C/920C

Page 54

No Location SDI CDT Toshiba CDT

Code No

Item/Spec

Code No

Item/Spec

1 R302 2004-001661 R-Metal Film;1/4W 3kohm,1% 2004-000481 R-Metal Film;1/4W 2.4kohm,1% 2 R303 2004-000268 R-Metal Film;1/4W 120ohm,1% 2004-002234 R-Metal Film;1/4W 560ohm,1% 3 R304 2004-000344 R-Metal Film;1/4W 15kohm,1% 2004-000412 R-Metal Film;1/4W 18kohm,1% 4 R305 2004-001136 R-Metal Film;1/4W 6.8kohm,1% 2004-001211 R-Metal Film;1/4W 7.5kohm,1% 5 R308 Do not use 2001-000049 R-Carbon;1/4W 2.4kohm,5% 6 C309 Do not use 2202-002009 C-Ceramic,Mono;50V 100nF 7 C422 2301-000016 C-Film,PEF;100V 22nF,5% 2301-000005 C-Film,PEF;100V 33nF,5% 8 R501 2004-001349 R-Metal Film;1/4W 91kohm,1% 2001-000962 R-Carbon;1/4W 75kohm,5% 9 R636 2001-000263 R-Carbon;1/2W 1.8ohm,5% 2001-000226 R-Carbon;1/2W 1.2ohm,5%

10 TCO Sensor BH39-00069A 1Pin TCO Sensor Wire Do not use

7-1-4 Different list for CDT - 720C

7-20 720C/920C

Page 55

Loc. No Code No. Description Specification Remark

CRT BH03-10339A CRT-COLOR M41QAQ261X151(T4/S-2/G) SDI

BH03-10339L CRT-COLOR M41LLH507XX701(F3) Toshiba

PBA UNIT BH94-00114E ASSY,PCB-SN US17HO(720C),NOKIA,W/WIDE SDI

BH94-00114F ASSY,PCB-TN US17HO(720C),NOKIA,W/WIDE Toshiba

B/D ASSY BH98-00118C ASSY,PCB/MAIN-SN US17HO(720C),NOKIA,W/WIDE SDI

BH98-00118D ASSY,PCB/MAIN-TN US17HO(720C),NOKIA,W/WIDE Toshiba BH98-00065C ASSY,PCB/VIDEO US17HO(720C),NOKIA,W/WIDE BH98-00079A ASSY,PCB/MISC-SOG US17HO(720C),NOKIA,W/WIDE

D/COIL BH27-00019A COIL-DEGAUSSING 290*315*1100mm,10.0mH

CRT GND ASSY

BH39-00125A CBF-HARNESS 1P,320mm,UL1015/3*0.16TA S/CABLE BH39-00124A CBF-SIGNAL CABLE 1830MM,15P/6P,8P,IVORY P/CORD BH39-10339E CBF-POWER CORD DET,SVT,125V/10A,IVORY USA

BH39-10007A CBF-POWER CORD DET,250V/10A,H05VV-F,LP-34,IVORY EUROPE TCO WIRE BH39-00069A CBF-HARNESS 1P,460MM,BLK,UL1015,AWG18 SDD Only

7-1-5 Others - 720C

7-21 720C/920C

Page 56

Main PCB Parts - 920C - Page 1

Loc. No Code No. Description Specification

BD201 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD261 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD262 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD265 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD266 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD401 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD402 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD403 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD501 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD503 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD532 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD601 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD602 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD605 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD630 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD631 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD651 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD663 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BOTTOM 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,-,5mm C201 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C202 2401-000486 C-AL 10uF,20%,50V,GP,TP,6.3x7mm,5 C203 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C204 2201-000247 C-CERAMIC,DISC 0.015nF,5%,50V,NP0,TP,5x3 C206 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C207 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C208 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C209 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C210 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C211 2301-000519 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x3x12.5,5 C212 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C213 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5, C214 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C215 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C217 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C218 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C219 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C220 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C221 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C222 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C223 2201-000138 C-CERAMIC,DISC 100pF,10%,50V,Y5P,TP,4.0X C224 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C225 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C226 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C262 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm C263 2202-002149 C-CERAMIC,MLC-RADIAL 0.82NF,2%,50V,NPO,T C264 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5 C265 2301-000005 C-FILM,PEF 33nF,5%,100V,TP,5.8x12.5x3,5

7-2 920C PCB Parts

7-22 720C/920C

Page 57

Main PCB Parts - 920C - Page 2

Loc. No Code No. Description Specification

C266 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C267 2202-002148 C-CERAMIC,MLC-RADIAL 0.68NF,2%,50V,NP0,T C268 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C269 2202-000654 C-CERAMIC,MLC-RADIAL 100nF,10%,50V,X7R,T C270 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 C271 2305-001041 C-FILM,MPEF 220nF,5%,63V,TP,7.5x4.5x13.5 C272 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5, C273 2301-000005 C-FILM,PEF 33nF,5%,100V,TP,5.8x12.5x3,5 C274 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C275 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C276 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C277 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C278 2401-003473 C-AL 680UF,20%,16V,GP,TP,10X12.5MM,5 C279 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C280 2201-000215 C-CERAMIC,DISC 0.12nF,5%,50V,NP0,TP,8.5x C282 2301-000168 C-FILM,PEF 150nF,5%,100V,TP,11.5x19mm,7. C283 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 C284 2305-000412 C-FILM,MPEF 470nF,5%,63V,TP,-,5mm C285 2401-000597 C-AL 1uF,20%,50V,GP,TP,4x7mm,1.5mm C301 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5 C302 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C305 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm, C306 2401-000856 C-AL 220uF,20%,35V,WT,TP,10x20,5 C307 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm, C308 2305-000237 C-FILM,MPEF 1uF,5%,63V,TP,7.5x15.5mm,5mm C310 2301-000519 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x3x12.5,5 C311 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5 C312 2401-000597 C-AL 1uF,20%,50V,GP,TP,4x7mm,1.5mm C313 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6. C401 2301-000188 C-FILM,PEF 1nF,5%,100V,TP,10.5x12.5x6.5, C402 2401-003525 C-AL 10uF,20%,250V,WT,LL,10x16,5 C403 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,-,5mm C405 2201-000132 C-CERAMIC,DISC 0.1nF,10%,500V,Y5P,TP,6.5 C406 2401-003524 C-AL 47uF,20%,100V,LL,TP,10x20mm C407 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,7.5x3 C408 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,-,5mm C409 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,-,5mm C410 2301-000020 C-FILM,PEF 27nF,5%,100V,TP,7.3x4x12.5mm, C411 2303-001022 C-FILM,PPF 2nF,5%,2.5KV,TP,23x12x19mm,7. C412 2303-001022 C-FILM,PPF 2nF,5%,2.5KV,TP,23x12x19mm,7. C413 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP, C418 2301-000102 C-FILM,PEF 1.2nF,5%,100V,TP,5.4x10mm,5mm C419 2201-000131 C-CERAMIC,DISC 0.1nF,10%,2kV,Y5P,TP,6.3x C420 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5 C421 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5 C422 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm C423 2202-000561 C-CERAMIC,MLC-RADIAL 680pF,5%,50V,NPO,TP

7-23 720C/920C

Page 58

Main PCB Parts - 920C - Page 3

Loc. No Code No. Description Specification

C424 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C425 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C426 2202-000470 C-CERAMIC,MLC-RADIAL 330pF,5%,100V,NPO,5 C427 2303-000011 C-FILM,PPF 1nF,5%,100V,TP,14x11.5mm,7.5m C428 2301-000020 C-FILM,PEF 27nF,5%,100V,TP,7.3x4x12.5mm, C429 2301-000284 C-FILM,PEF 47nF,5%,100V,TP,8.5x12.5mm,5m C430 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C431 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C432 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP, C451 2301-001249 C-FILM,MPPF 68nF,5%,400V,TP,19x7x15mm,7. C452 2301-001259 C-FILM,MPPF 100nF,5%,400V,TP,19x8x16,7.5 C453 2306-000179 C-FILM,MPPF 300nF,5%,250V,TP,20x18.5x10. C454 2306-000234 C-FILM,MPPF 560nF,5%,250V,BK,26x20x13,20 C455 2306-000147 C-FILM,MPPF 1uF,5%,250V,BK,26x24x15,22.5 C456 2306-000131 C-FILM,MPPF 150nF,5%,250V,TP,19x16x7.5,7 C457 2301-001249 C-FILM,MPPF 68nF,5%,400V,TP,19x7x15mm,7. C459 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C501 2301-001027 C-FILM,PEF 15nF,10%,250V,TP,9.5x12x4.5,5 C502 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C503 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C504 2401-001576 C-AL 47uF,20%,50V,GP,TP,8x11.5,5 C505 2401-000037 C-AL 470uF,20%,16V,GP,TP,8x11.5,5 C521 2301-000294 C-FILM,PEF 56nF,5%,100V,TP,9.5x12.5mm,5m C522 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm C523 2401-000292 C-AL 100uF,20%,16V,WT,TP,8x11.5mm,5 C524 2201-000163 C-CERAMIC,DISC 10nF,+80-20%,50V,Y5V,TP,7 C525 2305-001041 C-FILM,MPEF 220nF,5%,63V,TP,7.5x4.5x13.5 C526 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C527 2401-000971 C-AL 22uF,20%,50V,WT,TP,6x11mm,5mm C528 2401-001576 C-AL 47uF,20%,50V,GP,TP,8x11.5,5 C530 2201-000012 C-CERAMIC,DISC 0.22nF,10%,1kV,Y5P,TP,6.3 C531 2303-000147 C-FILM,PPF 1NF,5%,2KV,TP,23X13X8MM,7.5 C532 2401-000638 C-AL 2.2uF,20%,350V,WT,TP,10x12.5mm C533 2201-000732 C-CERAMIC,DISC 0.68nF,10%,1kV,Y5P,TP,7x4 C534 2401-001576 C-AL 47uF,20%,50V,GP,TP,8x11.5,5 C535 2401-000771 C-AL 220uF,20%,100V,WT,TP,16x25,7.5 C536 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C537 2401-000638 C-AL 2.2uF,20%,350V,WT,TP,10x12.5mm C538 2305-000665 C-FILM,MPEF 100nF,5%,63V,TP,7.5x4.0x5.0m C539 2401-000649 C-AL 2.2uF,20%,50V,BP,TP,5x11,5 C540 2201-000732 C-CERAMIC,DISC 0.68nF,10%,1kV,Y5P,TP,7x4 C551 2401-000043 C-AL 1uF,20%,160V,GP,TP,6.3x11,5mm C552 2305-000004 C-FILM,MPEF 220nF,10%,100V,TP,12.7x16,5m C555 2305-000004 C-FILM,MPEF 220nF,10%,100V,TP,12.7x16,5m C556 2201-000285 C-CERAMIC,DISC 1nF,10%,1kV,Y5P,TP,8x5,5 C557 2201-000012 C-CERAMIC,DISC 0.22nF,10%,1kV,Y5P,TP,6.3 C558 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3

7-24 720C/920C

Page 59

Main PCB Parts - 920C - Page 4

Loc. No Code No. Description Specification

C603 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP, C604 2305-001049 C-FILM,MPEF 1000nF,10%,275V,BK,31x23x13m C605 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C606 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C607 2401-000015 C-AL 33uF,20%,50V,WT,-,6.3x11mm,2.5 C608 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C609 2401-001137 C-AL 330uF,20%,400V,GP,BK,30x45mm,1 C610 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP, C611 2201-000012 C-CERAMIC,DISC 0.22nF,10%,1kV,Y5P,TP,6.3 C612 2201-000129 C-CERAMIC,DISC 0.1nF,10%,1kV,Y5P,TP,7x4, C614 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm C615 2301-000168 C-FILM,PEF 150nF,5%,100V,TP,11.5x19mm,7. C616 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C617 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm, C633 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2. C634 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C635 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C636 2401-003526 C-AL 100uF,20%,100V,LL,TP,12.5x20,5 C638 2401-000040 C-AL 47uF,20%,250V,WT,TP,16x25mm,7. C639 2401-001378 C-AL 470uF,20%,16V,WT,TP,10x20,5 C640 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5 C641 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6. C642 2401-000317 C-AL 100uF,20%,25V,WT,TP,8x11.5,5 C643 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5 C644 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C645 2401-001422 C-AL 470uF,20%,35V,WT,TP,12.5x25,5 C647 2301-000174 C-FILM,PEF 15nF,5%,100V,TP,7.2x4.0x7.5mm C648 2301-000004 C-FILM,PEF 2.2nF,5%,100V,TP,5.5X10X2.9,5 C649 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP, C652 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm C653 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C654 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C656 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C661 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C662 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2. C663 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5 C664 2201-000129 C-CERAMIC,DISC 0.1nF,10%,1kV,Y5P,TP,7x4, C665 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm, C666 2401-000913 C-AL 22uF,20%,16V,GP,TP,5x11mm,2.5m C667 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C668 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP, CIS 3301-000130 CORE-FERRITE AC,23.5x9.4x12.6mm,1500,280 CIS BH39-00059A CBF-HARNESS 3P/3P,420MM,GRY,UL2547,AWG26 CIS BH39-00060A CBF-HARNESS 15P/15P,180MM,WHT/BLU/RED/BL CIS BH39-00070A CBF-SIGNAL ATT,1830MM,15P/6P,8P,-,2990,D CN204 3711-004352 CONNECTOR-HEADER BOX,15P,1R,2MM,STRAIGHT CN208 3711-003843 CONNECTOR-HEADER BOX,8P,1R,2mm,STRAIGHT,

7-25 720C/920C

Page 60

Main PCB Parts - 920C - Page 5

Loc. No Code No. Description Specification

CN211 3711-004349 CONNECTOR-HEADER BOX,3P,1R,2MM,STRAIGHT, CN212 3711-004349 CONNECTOR-HEADER BOX,3P,1R,2MM,STRAIGHT, CN401 3711-003989 CONNECTOR-HEADER NOWALL,4P,1R,8mm,STRAIG CN409 3711-000434 CONNECTOR-HEADER 3WALL,2P,1R,2.5mm,STRAI D201 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D202 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D203 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D262 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D264 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D301 0402-000272 DIODE-RECTIFIER UF4001,50V,1A,DO-41,TP D302 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D401 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D402 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D403 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D405 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D406 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D407 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D408 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D409 0402-000272 DIODE-RECTIFIER UF4001,50V,1A,DO-41,TP D410 0402-001215 DIODE-RECTIFIER SDS10U150S,1.5KV,10A,TOD411 0402-000007 DIODE-RECTIFIER 1N4937GP,600V,1A,DO-41,T D412 0402-000007 DIODE-RECTIFIER 1N4937GP,600V,1A,DO-41,T D413 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP D414 0402-000272 DIODE-RECTIFIER UF4001,50V,1A,DO-41,TP D415 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T D416 0402-000454 DIODE-RECTIFIER RG10V1,400V,1.2A,DO-201 D451 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D501 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T D502 0402-001114 DIODE-RECTIFIER 1N4936GP,400V,1A,DO-204A D503 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D504 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D506 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D521 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D522 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D523 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D524 0402-001295 DIODE-RECTIFIER GUR460L-5700,600V,4A,DOD525 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D526 0402-001295 DIODE-RECTIFIER GUR460L-5700,600V,4A,DOD527 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP D528 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D529 0402-000007 DIODE-RECTIFIER 1N4937GP,600V,1A,DO-41,T D530 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D551 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D552 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D553 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D554 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D601 0402-001227 DIODE-BRIDGE D3SBA60,600V,2.3A,SIP-4,BK

7-26 720C/920C

Page 61

Main PCB Parts - 920C - Page 6

Loc. No Code No. Description Specification

D604 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T D605 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP D606 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D607 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP D608 0403-001028 DIODE-ZENER BZT03C160,160V,153-171V,3.25 D630 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D632 0402-001289 DIODE-RECTIFIER 31DF6,600V,3A,DO-201AD,B D633 0402-000250 DIODE-RECTIFIER RG4C,1000V,1A,D634 0402-001190 DIODE-RECTIFIER RG10Z,200V,1.2A,DO-15,TP D635 0402-001118 DIODE-RECTIFIER UF1G,400V,1.2A,DO-204AL, D636 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D637 0402-001294 DIODE-RECTIFIER UF5404L-5709,400V,3A,DOD638 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D639 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D661 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D662 0402-000126 DIODE-RECTIFIER 1N4001GP,50V,1A,DO-41,TP D663 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T F633 3601-001092 FUSE-AXIALLEAD 125V,2.5A,SLOW-BLOW,EPOXY FG601 3601-000455 FUSE-CARTRIDGE 250V,4A,TIME-LAG,CERAMIC, FH601 3602-000001 FUSE-CLIP -,-,30mohm IC201 0903-001166 IC-MICROCONTROLLER 88P6232,8BIT,DIP,42P, IC202 1203-000495 IC-RESET 7045,T0-92,3P,-,PLASTIC,4.3/4. IC203 1103-001150 IC-EEPROM 24C081,8KBIT,DIP,8P,300MIL,10M IC204 1103-001087 IC-EEPROM 24LC21,128x8BIT,DIP,8P,300MIL, IC261 1204-001448 IC-DEF.PROCESSOR SAM9222G,DIP,32P,300MI IC301 1204-001508 IC-VERTICALDEF. KA2142,SIP,10P,-,PLASTIC IC402 1203-001099 IC-PWMCONTROLLER 3843,DIP,8P,250MIL,PLAS IC403 BH13-00009A IC-H/VCONVERGENCE PG17/19,AN5452,SIP,12P IC501 1203-000610 IC-PWMCONTROLLER 494,DIP,16P,300MIL,PLAS IC502 1201-000420 IC-OPAMP 358,DIP,8P,300MIL,DUAL,100V/mV IC601 BH13-00012A IC-POWERSWITCH PG17/19/21,DP308O,TO-3P-5 IC602 0604-001018 PHOTO-COUPLER DAR-TR,63-125%,200mW,DIP-4 IC604 1203-000002 IC-POSI.ADJUSTREG. 431,TO-92,3P,-,PLAST IC605 1203-000165 IC-POSI.ADJUSTREG. 78R12,TO-220,3P,-,-,1 IC606 1203-000001 IC-POSI.FIXEDREG. 7805,TO-220,3P,-,PLAST IC661 0604-001018 PHOTO-COUPLER DAR-TR,63-125%,200mW,DIP-4 JP495 2004-001298 R-METAL 82Kohm,2%,1/4W,AA,TP,2.4x6.4mm L260 2701-000154 INDUCTOR-AXIAL 220uH,10%,4.2x9.8mm L401 2701-000187 INDUCTOR-AXIAL 4.7uH,10%,4.2x9.8mm L402 BH27-20345J COIL-HORIZ.CENTER 3.5mH,-,OB6*30-1HHA,BU L403 BH26-30338W TRANS-H.LINEARITY 47.5mH/3.9uH,5P,DR1420 L404 2701-000179 INDUCTOR-AXIAL 33uH,10%,4.2x9.8mm L405 2701-000179 INDUCTOR-AXIAL 33uH,10%,4.2x9.8mm L501 2701-000179 INDUCTOR-AXIAL 33uH,10%,4.2x9.8mm L503 2701-000187 INDUCTOR-AXIAL 4.7uH,10%,4.2x9.8mm L521 BH27-00027A COIL-CHOKE-1 8.5UH,-,DR1215(C:7.0),BK,-, L601 BH27-00026A COIL-LINEFILTER 15MHMIN,-,SQE2828,BK,-,-

7-27 720C/920C

Page 62

Main PCB Parts - 920C - Page 7

Loc. No Code No. Description Specification

LC601 2901-001161 FILTER-EMIACLINE 250V,3A,UL/CSA/SEMKO,22 OP1 0601-000463 LED ROUND,G/O,4.8mm,565/585nm PCB BH41-00037A P.C.B-MAIN -,FR1,-,247*320*1.6,1.6T POS601 1404-000002 THERMISTOR-PTC 9ohm,20%,-,-,TR,RECT,Q261 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q262 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP Q263 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q264 0505-000013 FET-SILICON VN2222LL,N,60V,150mA,7.5ohm, Q290 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q301 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q401 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP Q403 0505-001130 FET-SILICON IRF740A,N,400V,10uA,550mohm, Q404 0505-001357 FET-SILICON SKS4N20,N,200V,3A,1.3OHM,27W Q405 0502-001142 TR-POWER 2SC5584,NPN,150W,TO-3PL,ST,7-1 Q451 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q452 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q453 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q454 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q455 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q456 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM Q457 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM Q458 0505-001358 FET-SILICON SKS19N20,N,200V,11.8A,0.15OH Q459 0505-001358 FET-SILICON SKS19N20,N,200V,11.8A,0.15OH Q460 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM Q501 0501-000143 TR-SMALLSIGNAL 2N6520,PNP,625mW,TO-92,-, Q521 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q522 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q523 0501-000581 TR-SMALLSIGNAL 2N3906,PNP,625mW,TO-92,TP Q524 0505-001266 FET-SILICON 2SK2761-01MR,N,600V,10A,0.85 Q551 0502-000348 TR-POWER TIP29C,NPN,2W,TO-220,-,15-75 Q552 0502-000351 TR-POWER TIP30,PNP,2W,TO-220AB,-,15-75 Q553 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92,-, Q554 0501-000413 TR-SMALLSIGNAL KSP44,NPN,625mW,TO-92,-,5 Q630 0501-000010 TR-SMALLSIGNAL KSC1008,NPN,800mW,TO-92,T Q632 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q663 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q664 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP R201 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R202 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R203 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R204 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R205 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R206 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R207 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R208 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM R209 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM R211 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM

7-28 720C/920C

Page 63

Main PCB Parts - 920C - Page 8

Loc. No Code No. Description Specification

R212 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R214 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM R215 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R216 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R217 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R218 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R219 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R220 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R221 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R222 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R223 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R224 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R225 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R226 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R227 2004-001285 R-METAL 820ohm,1%,1/4W,AA,TP,2.4x6.4mm R229 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R230 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R231 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R232 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R233 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R234 2004-000344 R-METAL 15Kohm,1%,1/4W,AA,TP,2.4x6.4mm R235 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R236 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R237 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R238 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R239 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R240 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R241 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R242 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R243 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R244 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R245 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM R246 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM R247 2001-000435 R-CARBON 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM R261 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R262 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R263 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R264 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R265 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R266 2001-000744 R-CARBON 4.7OHM,5%,1/8W,AA,TP,1.8X3.2MM R267 2004-001118 R-METAL 5Kohm,1%,1/4W,AA,TP,2.4x6.4mm R268 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R269 2001-003190 R-CARBON 2.5MOHM,5%,1/8W,AA,TP,1.8X3.2MM R270 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R271 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R272 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM R273 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM

7-29 720C/920C

Page 64

Main PCB Parts - 920C - Page 9

Loc. No Code No. Description Specification

R274 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R275 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R276 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R277 2001-000009 R-CARBON 20KOHM,5%,1/8W,AA,TP,1.8X3.2MM R278 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R279 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R280 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R281 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R282 2001-000319 R-CARBON 120KOHM,5%,1/8W,AA,TP,1.8X3.2MM R283 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R284 2004-004367 R-METAL 90Kohm,1%,1/4W,AA,TP,6.2x2.6mm R285 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R286 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R287 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R288 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R289 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R290 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R291 2001-000007 R-CARBON 3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R292 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM R293 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R294 2001-000007 R-CARBON 3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R295 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM R296 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM R297 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R298 2003-000669 R-METALOXIDE(S) 390ohm,5%,1W,AA,TP,3.3x9 R299 2001-001107 R-CARBON(S) 220ohm,5%,1/2W,AA,TP,2.4x6.4 R301 2004-000616 R-METAL 24Kohm,1%,1/4W,AA,TP,2.4x6.4mm R302 2004-000728 R-METAL 3.9Kohm,1%,1/4W,AA,TP,2.4x6.4m R303 2004-002234 R-METAL 560ohm,1%,1/4W,AA,TP,2.4x6.4mm R304 2004-000412 R-METAL 18Kohm,1%,1/4W,AA,TP,2.4x6.4mm R305 2004-000216 R-METAL 10Kohm,1%,1/4W,AA,TP,2.4x6.4mm R306 2005-001064 R-WIREWOUND 0.9OHM,5%,2W,AA,TP,3.8X11MM R309 2001-000016 R-CARBON(S) 1OHM,5%,1/2W,AA,TP,2.4X6.4MM R310 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R311 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R312 2001-000977 R-CARBON 8.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R313 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R314 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R315 2008-000114 R-FUSIBLE 1.2ohm,5%,1/2W,AA,TP,3.5x9.4mm R316 2008-000114 R-FUSIBLE 1.2ohm,5%,1/2W,AA,TP,3.5x9.4mm R401 2001-000017 R-CARBON 4.7OHM,5%,1/4W,AA,TP,2.4X6.4MM R402 2001-000645 R-CARBON 330KOHM,5%,1/8W,AA,TP,1.8X3.2MM R403 2001-000011 R-CARBON 75KOHM,5%,1/8W,AA,TP,1.8X3.2MM R404 2001-000679 R-CARBON 36KOHM,5%,1/8W,AA,TP,1.8X3.2MM R405 2003-000763 R-METALOXIDE(S) 6.8ohm,5%,3W,AA,TP,6x16m R406 2001-000006 R-CARBON 2.4KOHM,5%,1/8W,AA,TP,1.8X3.2MM R407 2001-000958 R-CARBON 750OHM,5%,1/8W,AA,TP,1.8X3.2MM

7-30 720C/920C

Page 65

Main PCB Parts - 920C - Page 10

Loc. No Code No. Description Specification

R408 2001-000011 R-CARBON 75KOHM,5%,1/8W,AA,TP,1.8X3.2MM R409 2001-000037 R-CARBON(S) 330OHM,5%,1/2W,AA,TP,2.4X6.4 R410 2006-001070 R-CEMENT 1.8OHM,5%,5W,CA,BK,9.5X22X9.5MM R411 2006-000195 R-CEMENT 51OHM,5%,5W,CA,BK,9.5X22X9.5MM R412 2006-000195 R-CEMENT 51OHM,5%,5W,CA,BK,9.5X22X9.5MM R413 2001-000539 R-CARBON 24KOHM,5%,1/8W,AA,TP,1.8X3.2MM R414 2004-000284 R-METAL 12Kohm,1%,1/4W,AA,TP,2.4x6.4mm R415 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM R416 2001-001163 R-CARBON(S) 560OHM,5%,1/2W,AA,TP,2.4X6.4 R417 2004-000216 R-METAL 10Kohm,1%,1/4W,AA,TP,2.4x6.4mm R418 2003-000724 R-METALOXIDE(S) 5.6ohm,5%,3W,AA,TP,6x16m R419 2001-000019 R-CARBON(S) 10OHM,5%,1/2W,AA,TP,2.4X6.4M R420 2003-000595 R-METALOXIDE(S) 240ohm,5%,2W,AA,TP,4x12m R421 2003-000695 R-METALOXIDE(S) 430ohm,5%,3W,AA,TP,6x16m R422 2001-000028 R-CARBON(S) 100OHM,5%,1/2W,AA,TP,2.4X6.4 R423 2001-000028 R-CARBON(S) 100OHM,5%,1/2W,AA,TP,2.4X6.4 R424 2001-000947 R-CARBON 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM R429 2003-000423 R-METALOXIDE(S) 1.2ohm,5%,3W,AA,TP,6x16m R432 2004-004038 R-METAL 4.3Kohm,1%,1/4W,AA,TP,2.4x6.4m R433 2004-000532 R-METAL 20Kohm,1%,1/4W,AA,TP,2.4x6.4mm R434 2001-001187 R-CARBON(S) 75OHM,5%,1/2W,AA,TP,2.4X6.4M R435 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM R436 2008-000147 R-FUSIBLE 22ohm,5%,1/4W,AA,TP,2.6x6.7mm R437 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM R438 2008-000140 R-FUSIBLE 2.2ohm,5%,1/2W,AA,TP,3.5x9.4mm R451 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R452 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R453 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R454 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R455 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R456 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R457 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R458 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R459 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R460 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R461 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R462 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R463 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R464 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R465 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R466 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R467 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R468 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R469 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R470 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R471 2003-000450 R-METALOXIDE(S) 100Kohm,5%,3W,AA,TP,6x16 R476 2003-000661 R-METALOXIDE(S) 33ohm,5%,2W,AA,TP,4x12mm

7-31 720C/920C

Page 66

Main PCB Parts - 920C - Page 11

Loc. No Code No. Description Specification

R477 2001-000022 R-CARBON(S) 33OHM,5%,1/2W,AA,TP,2.4X6.4M R501 2001-000115 R-CARBON 82KOHM,5%,1/4W,AA,TP,2.4X6.4MM R502 2004-000327 R-METAL 150Kohm,1%,1/4W,AA,TP,2.4x6.4m R503 2001-000096 R-CARBON(S) 1MOHM,5%,1/2W,AA,TP,2.4X6.4M R504 2001-000546 R-CARBON 270KOHM,5%,1/4W,AA,TP,2.4X6.4MM R506 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM R507 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R508 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM R509 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R510 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM R511 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R512 2004-000861 R-METAL 39Kohm,1%,1/4W,AA,TP,2.4x6.4mm R513 2004-000515 R-METAL 200Kohm,1%,1/4W,AA,TP,2.4x6.4m R521 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM R523 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM R524 2001-000689 R-CARBON 390KOHM,5%,1/8W,AA,TP,1.8X3.2MM R525 2001-000977 R-CARBON 8.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R526 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM R527 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R528 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM R529 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R530 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R532 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R533 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM R534 2001-000018 R-CARBON 6.8OHM,5%,1/4W,AA,TP,2.4X6.4MM R535 2005-000210 R-WIREWOUND 0.33ohm,5%,1W,AC,BK,4.5x11mm R536 2003-000014 R-METALOXIDE(S) 10Kohm,5%,3W,AA,TP,6x16m R537 2003-000014 R-METALOXIDE(S) 10Kohm,5%,3W,AA,TP,6x16m R538 2001-000073 R-CARBON 33KOHM,5%,1/4W,AA,TP,2.4X6.4MM R539 2006-001066 R-CEMENT 33OHM,5%,7W,CS,BK,9X10X54MM R540 2004-001349 R-METAL 91Kohm,1%,1/4W,AA,TP,2.4x6.4mm R543 2001-000878 R-CARBON 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R549 2003-000462 R-METALOXIDE(S) 10Kohm,5%,2W,AA,TP,4x12m R551 2003-000006 R-METALOXIDE 47ohm,5%,1W,AA,TP,4.3x12mm R552 2001-000066 R-CARBON(S) 10KOHM,5%,1/2W,AA,TP,2.4X6.4 R553 2001-001153 R-CARBON(S) 47OHM,5%,1/2W,AA,TP,2.4X6.4M R554 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R555 2001-000319 R-CARBON 120KOHM,5%,1/8W,AA,TP,1.8X3.2MM R556 2001-000045 R-CARBON 1.8KOHM,5%,1/4W,AA,TP,2.4X6.4MM R558 2003-000462 R-METALOXIDE(S) 10Kohm,5%,2W,AA,TP,4x12m R560 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM R561 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM R562 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R563 2001-001186 R-CARBON(S) 75KOHM,5%,1/2W,AA,TP,2.4X6.4 R564 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6. R565 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6. R566 2001-001186 R-CARBON(S) 75KOHM,5%,1/2W,AA,TP,2.4X6.4

7-32 720C/920C

Page 67

Main PCB Parts - 920C - Page 12

Loc. No Code No. Description Specification

R570 BH39-40305U CBF-HARNESS J/WIRE,50mm R601 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM R603 2001-000044 R-CARBON 1.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM R604 2001-000087 R-CARBON(S) 120KOHM,5%,1/2W,AA,TP,2.4X6. R605 2001-000085 R-CARBON(S) 100KOHM,5%,1/2W,AA,TP,2.4X6. R607 2001-000376 R-CARBON 15OHM,5%,1/8W,AA,TP,1.8X3.2MM R608 2003-000756 R-METALOXIDE(S) 6.8Kohm,5%,3W,AA,TP,6x16 R609 2001-000552 R-CARBON 270OHM,5%,1/4W,AA,TP,2.4X6.4MM R611 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM R630 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R631 2001-000023 R-CARBON 47OHM,5%,1/4W,AA,TP,2.4X6.4MM R632 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm R633 2001-001106 R-CARBON(S) 220KOHM,5%,1/2W,AA,TP,2.4X6. R634 2001-001131 R-CARBON(S) 33KOHM,5%,1/2W,AA,TP,2.4X6.4 R635 2001-001113 R-CARBON(S) 270KOHM,5%,1/2W,AA,TP,2.4X6. R636 2003-000422 R-METALOXIDE(S) 1.2ohm,5%,2W,AA,TP,4x12m R637 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R638 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R639 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM R640 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R641 2001-000034 R-CARBON 220OHM,5%,1/4W,AA,TP,2.4X6.4MM R642 2001-000508 R-CARBON 220KOHM,5%,1/8W,AA,TP,1.8X3.2MM R643 2003-000521 R-METALOXIDE(S) 180Kohm,5%,1W,AA,TP,3.3x R644 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM R645 2004-000679 R-METAL 2Kohm,1%,1/4W,AA,TP,2.4x6.4mm R646 2004-000334 R-METAL 150ohm,1%,1/4W,AA,TP,2.4x6.4mm R648 2001-001113 R-CARBON(S) 270KOHM,5%,1/2W,AA,TP,2.4X6. R651 2001-001138 R-CARBON(S) 390OHM,5%,1/2W,AA,TP,2.4X6.4 R657 2001-000495 R-CARBON 20KOHM,5%,1/4W,AA,TP,2.4X6.4MM R661 2001-001050 R-CARBON(S) 1.5KOHM,5%,1/2W,AA,TP,2.4X6. R662 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R663 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM R664 2001-000495 R-CARBON 20KOHM,5%,1/4W,AA,TP,2.4X6.4MM R665 2004-000964 R-METAL 470Kohm,1%,1/4W,AA,TP,2.4x6.4m R666 2004-000964 R-METAL 470Kohm,1%,1/4W,AA,TP,2.4x6.4m R667 2004-001211 R-METAL 7.5Kohm,1%,1/4W,AA,TP,2.4x6.4m R668 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R669 2001-000793 R-CARBON 47OHM,5%,1/8W,AA,TP,1.8X3.2MM RL601 3501-001111 RELAY-POWER 12Vdc,250mW,5A,1FormA,15mS,5 SK521 4715-000001 SURGEABSORBER 1KV,+50-10%,-,-, SW1 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP SW2 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP SW3 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP SW4 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP SW5 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP SW6 3403-001075 SWITCH-PUSH 30Vdc,300mA,DPDT,OFF-ON-OFF, SW7 3404-001079 SWITCH-TACT 12VDC,50MA,160GF,8.4X15.55X2

7-33 720C/920C

Page 68

Main PCB Parts - 920C - Page 13

Loc. No Code No. Description Specification

T401 BH26-00030A TRANS-HOR.DRIVE 2.8MH,8P,EI2519,PL3,PM2, T402 BH26-00040A TRANS-HOR.PULSE 1.5MH,10P,EI-3026,PL3,-, T403 BH26-00002A TRANS-H.GATE 520UH,5P,EI-1614,SB-5S,520U T501 BH26-00051A TRANS-FBT 80.4UH,14P,HV22UR,HV22U,-,-,FE T502 BH26-00056A TRANS-FOCUS 3.8MHMIN,10P,SB-5S,EI-2218,S T601 BH26-00050A TRANS-POWER 130UH,18P,EER4445,PL3,130UH/ T602 BH26-30302S TRANS-SYNC. 3-1(250UH),-,-,SB-5S,UU1116, T661 BH26-00042A TRANS 2.5MH,8P,EI-1916,PL3,-,150UH,TH601 1404-001076 THERMISTOR-NTC 8ohm,15%,-,17mW/C,TP VR401 2103-001049 VR-SEMI 100ohm,30%,1/5W,SIDE VR501 2103-001080 VR-SEMI 100KOHM,25%,0.3W,SIDE X201 2801-000006 CRYSTAL-UNIT 12MHz,50ppm,28-AAM,S,35ohm, ZD241 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD242 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD243 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD245 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD246 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD247 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD248 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD249 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD250 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD252 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500 ZD260 0403-000509 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500 ZD501 0403-000355 DIODE-ZENER UZ5.1BSB,5.1V,4.97-5.18V,500 ZD601 0403-000753 DIODE-ZENER MTZJ27D,27V,26.29-27.64V,500 ZD602 0403-001068 DIODE-ZENER UZ4.7BSA,4.7V,4.47-4.65V,500 ZD661 0403-000367 DIODE-ZENER UZ7.5BSC,7.5V,7.33-7.64V,500

7-34 720C/920C

Page 69

Loc. No Code No. Description Specification Remark

BD101 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, Page 01 BD105 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD106 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD151 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD155 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, BD181 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500, C102 2202-000319 C-CERAMIC,MLC-RADIAL 100nF,10%,100V,X7R, C103 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C104 2401-003224 C-AL 470uF,20%,16V,WT,TP,8X11.5,5mm C105 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP, C106 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C107 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C108 2401-003224 C-AL 470uF,20%,16V,WT,TP,8X11.5,5mm C109 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C110 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C111 2202-000319 C-CERAMIC,MLC-RADIAL 100nF,10%,100V,X7R, C112 2401-003484 C-AL 10uF,20%,100V,LZ,TP,6.3X11,5 C113 2401-000393 C-AL 10uF,20%,100V,WT,TP,8x11.5,5 C114 2401-000393 C-AL 10uF,20%,100V,WT,TP,8x11.5,5 C115 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5 C116 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5 C117 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2. C118 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C119 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C120 2201-000247 C-CERAMIC,DISC 0.015nF,5%,50V,NP0,TP,5x3 C124 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C126 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5 C128 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C141 2201-000764 C-CERAMIC,DISC 0.082nF,5%,50V,NP0,TP,8x3 C142 2202-000654 C-CERAMIC,MLC-RADIAL 100nF,10%,50V,X7R,T C150 2401-003224 C-AL 470uF,20%,16V,WT,TP,8X11.5,5mm C151 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C152 2202-000669 C-CERAMIC,MLC-RADIAL 10nF,10%,50V,X7R,TP C154 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C155 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C156 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2. C157 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C158 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C161 2202-000669 C-CERAMIC,MLC-RADIAL 10nF,10%,50V,X7R,TP C167 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5 C168 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 C169 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 C170 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C171 2201-000234 C-CERAMIC,DISC 0.15nF,5%,50V,NP0,TP,9x3,

7-2-2 Video PCB Parts - 920C

7-35 720C/920C

Page 70

Loc. No Code No. Description Specification Remark

Video PCB Parts - 920C

C172 2201-000234 C-CERAMIC,DISC 0.15nF,5%,50V,NP0,TP,9x3, Page 02 C181 2201-000288 C-CERAMIC,DISC 1nF,10%,2kV,Y5P,TP,9x5,10 C183 2201-000530 C-CERAMIC,DISC 4.7nF,10%,500V,Y5P,TP,12. CB01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CB02 2202-000319 C-CERAMIC,MLC-RADIAL 100nF,10%,100V,X7R, CB11 2201-000222 C-CERAMIC,DISC 0.012nF,5%,50V,NP0,TP,5x3 CB12 2201-000504 C-CERAMIC,DISC 0.039nF,5%,50V,SL,TP,5x3, CB14 2305-000009 C-FILM,MPEF 100nF,5%,250V,TP,13x11x6.5,7 CB16 2401-001318 C-AL 470nF,20%,100V,GP,TP,5x11,5 CB17 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5 CB21 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CBC 2201-002080 C-CERAMIC,DISC 0.027NF,5%,500V,NPO,TP,6. CG01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CG02 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5 CG03 2202-000319 C-CERAMIC,MLC-RADIAL 100nF,10%,100V,X7R, CG04 2401-000597 C-AL 1uF,20%,50V,GP,TP,4x7mm,1.5mm CG11 2201-000689 C-CERAMIC,DISC 0.008nF,0.5pF,50V,NP0,TP, CG12 2201-000504 C-CERAMIC,DISC 0.039nF,5%,50V,SL,TP,5x3, CG14 2305-000009 C-FILM,MPEF 100nF,5%,250V,TP,13x11x6.5,7 CG16 2401-001318 C-AL 470nF,20%,100V,GP,TP,5x11,5 CG17 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5 CG21 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V CGC 2201-002080 C-CERAMIC,DISC 0.027NF,5%,500V,NPO,TP,6. CN101 3711-004228 CONNECTOR-HEADER BOX,6P,1R,2MM,ANGLE,SN CN102 3711-004123 CONNECTOR-HEADER BOX,15P,1R,2mm,ANGLE,SN CR01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CR02 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5 CR11 2201-000689 C-CERAMIC,DISC 0.008nF,0.5pF,50V,NP0,TP, CR12 2201-000504 C-CERAMIC,DISC 0.039nF,5%,50V,SL,TP,5x3, CR14 2305-000009 C-FILM,MPEF 100nF,5%,250V,TP,13x11x6.5,7 CR16 2401-003479 C-AL 0.47UF,20%,100V,WT,TP,5X11MM,5 CR17 2401-003479 C-AL 0.47UF,20%,100V,WT,TP,5X11MM,5 CR21 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CRC 2201-002080 C-CERAMIC,DISC 0.027NF,5%,500V,NPO,TP,6. D104 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, D151 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DB01 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DB02 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DB03 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DB04 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DB05 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DB07 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DG01 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DG02 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35,

7-36 720C/920C

Page 71

Loc. No Code No. Description Specification Remark

Video PCB Parts - 920C

DG03 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T Page 03 DG04 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DG05 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DG07 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DR01 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DR02 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DR03 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DR04 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DR05 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, DR07 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35, IC101 1201-001287 IC-VIDEOAMP 52748,DIP,36P,500MIL,TRIPLE IC102 BH13-10335P IC-HYBRID S-PROJECT,VPS14,ZIP,15P,CRT/DR IC103 1204-001547 IC-OSDPROCESSOR KS2501B-10,DIP,24P,300MI IC104 1201-001242 IC-PREAMP 52324,DIP,18P,-,DUAL,-,PLASTIC JP124 2701-000187 INDUCTOR-AXIAL 4.7uH,10%,4.2x9.8mm L101 2701-000125 INDUCTOR-AXIAL 150uH,10%,3x7mm L102 2701-000125 INDUCTOR-AXIAL 150uH,10%,3x7mm LB03 2701-001069 INDUCTOR-AXIAL 180NH,10%,3X7MM LG03 2701-001069 INDUCTOR-AXIAL 180NH,10%,3X7MM LR03 2701-001065 INDUCTOR-AXIAL 0.22UH,10%,3X7MM PCB BH41-00028A PCB-VIDEO -,FR1,-,247*330,1.6T Q101 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q102 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q103 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q104 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q141 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP QB02 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92,-, QB03 0501-000138 TR-SMALLSIGNAL 2N5401,PNP,625mW,TO-92,TP QB51 0501-000581 TR-SMALLSIGNAL 2N3906,PNP,625mW,TO-92,TP QG02 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92,-, QG03 0501-000138 TR-SMALLSIGNAL 2N5401,PNP,625mW,TO-92,TP QG51 0501-000581 TR-SMALLSIGNAL 2N3906,PNP,625mW,TO-92,TP QR02 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92,-, QR03 0501-000138 TR-SMALLSIGNAL 2N5401,PNP,625mW,TO-92,TP QR51 0501-000581 TR-SMALLSIGNAL 2N3906,PNP,625mW,TO-92,TP R101 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R102 2001-001000 R-CARBON 82KOHM,5%,1/8W,AA,TP,1.8X3.2MM R103 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R110 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R111 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R112 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R113 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R114 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R115 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM

7-37 720C/920C

Page 72

Loc. No Code No. Description Specification Remark

Video PCB Parts - 920C

R116 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM Page 04 R117 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R118 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R119 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R120 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R121 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R122 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R124 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MM R125 2001-000006 R-CARBON 2.4KOHM,5%,1/8W,AA,TP,1.8X3.2MM R126 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM R127 2001-000356 R-CARBON 150KOHM,5%,1/8W,AA,TP,1.8X3.2MM R131 2004-000150 R-METAL 1.5Kohm,1%,1/4W,AA,TP,2.4x6.4m R141 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R142 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R151 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R152 2001-000633 R-CARBON 30KOHM,5%,1/8W,AA,TP,1.8X3.2MM R153 2001-000325 R-CARBON 120OHM,5%,1/8W,AA,TP,1.8X3.2MM R156 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MM R157 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MM R158 2001-000878 R-CARBON 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R159 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R161 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R162 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R164 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm R165 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R168 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R169 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R170 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R171 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R172 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R175 2002-001022 R-COMPOSITION 30MOHM,5%,1/4W,AA,TP,2.5X6 R181 2001-001107 R-CARBON(S) 220ohm,5%,1/2W,AA,TP,2.4x6.4 R183 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM RB01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM RB02 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM RB04 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM RB05 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM RB06 2001-000666 R-CARBON 33OHM,5%,1/8W,AA,TP,1.8X3.2MM RB11 2001-000666 R-CARBON 33OHM,5%,1/8W,AA,TP,1.8X3.2MM RB12 2001-000005 R-CARBON 390ohm,5%,1/8W,AA,TP,1.8x3.2mm RB14 2001-000482 R-CARBON 200KOHM,5%,1/4W,AA,TP,2.4X6.4MM RB15 2001-000047 R-CARBON 2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM RB16 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM RB17 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4M

7-38 720C/920C

Page 73

Loc. No Code No. Description Specification Remark

Video PCB Parts - 920C

RB18 2001-001185 R-CARBON(S) 750OHM,5%,1/2W,AA,TP,2.4X6.4 Page 05 RB21 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM RB26 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm RB31 2001-000110 R-CARBON 10OHM,5%,1/4W,AA,TP,2.4X6.4MM RBR 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM RG01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM RG02 2001-000666 R-CARBON 33OHM,5%,1/8W,AA,TP,1.8X3.2MM RG03 2001-000995 R-CARBON 820OHM,5%,1/8W,AA,TP,1.8X3.2MM RG04 2001-000356 R-CARBON 150KOHM,5%,1/8W,AA,TP,1.8X3.2MM RG05 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM RG06 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM RG11 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM RG12 2001-000005 R-CARBON 390ohm,5%,1/8W,AA,TP,1.8x3.2mm RG14 2001-000482 R-CARBON 200KOHM,5%,1/4W,AA,TP,2.4X6.4MM RG15 2001-000047 R-CARBON 2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM RG16 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM RG17 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4M RG18 2001-000109 R-CARBON(S) 470OHM,5%,1/2W,AA,TP,2.4X6.4 RG21 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM RG26 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm RG31 2001-000333 R-CARBON 12OHM,5%,1/4W,AA,TP,2.4X6.4MM RGG 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM RR01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM RR02 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM RR04 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM RR05 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM RR06 2001-000666 R-CARBON 33OHM,5%,1/8W,AA,TP,1.8X3.2MM RR11 2001-000666 R-CARBON 33OHM,5%,1/8W,AA,TP,1.8X3.2MM RR12 2001-000005 R-CARBON 390ohm,5%,1/8W,AA,TP,1.8x3.2mm RR14 2001-000482 R-CARBON 200KOHM,5%,1/4W,AA,TP,2.4X6.4MM RR15 2001-000047 R-CARBON 2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM RR16 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM RR17 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4M RR18 2001-001185 R-CARBON(S) 750OHM,5%,1/2W,AA,TP,2.4X6.4 RR21 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM RR26 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm RR31 2001-000110 R-CARBON 10OHM,5%,1/4W,AA,TP,2.4X6.4MM RRR 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM SK101 4715-000102 SURGEABSORBER 200V,20%,1000A,-,RADIAL SK102 4715-000102 SURGEABSORBER 200V,20%,1000A,-,RADIAL SK103 4715-000102 SURGEABSORBER 200V,20%,1000A,-,RADIAL SK104 4715-000106 SURGEABSORBER 300V,210-390V,-,-,AXIAL SK105 3704-001116 SOCKET-CRT 11P,22.5PI,26.5PI,NI,SK108 4715-000001 SURGEABSORBER 1KV,+50-10%,-,-,

7-39 720C/920C

Page 74

Loc. No Code No. Description Specification Remark

Video PCB Parts - 920C

ZD101 0403-000509 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500 Page 06 ZD102 0403-000509 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500

7-40 720C/920C

Page 75

No Location SDI CDT Matsushita CDT Remark

Code No

Item/Spec

Code No

Item/Spec

C309 Do not use 2202-002009 C-CER 100nF 50V

C310 2301-000519 C-POLY 3.3nF 100V 2301-000013 C-POLY 4.7nF 100V

C451 2301-001249 C-FILM MPPF 68nF 400V 2301-001273 C-FILM MPEF 56nF 400V

C457 2301-001249 C-FILM MPPF 68nF 400V 2306-000224 C-FILM MPEF 47nF 400V

R307 Do not use 2001-001088 R-CF 1Kohm 1/2W

R308 Do not use 2001-000049 R-CF 2.4Kohm 1/2W

R303 2004-002234 R-MF 560ohm 1/4W 2004-000940 R-MF 430ohm 1/4W

R304 2004-000412 R-MF 18Kohm 1/4W 2004-000344 R-MF 15Kohm 1/4W

R305 2004-000216 R-MF 10Kohm 1/4W 2004-001254 R-MF 8.2Kohm 1/4W

R561 2001-000812 R-CF 5.6Kohm 1/8W 2001-000890 R-CF 6.8Kohm 1/8W

R562 2001-000221 R-CF 1.2Kohm 1/8W 2001-000241 R-CF 1.5Kohm 1/8W

R410 2006-001070 R-CEMENT 1.8ohm 5W 2006-001069 R-CEMENT 2.2ohm 5W

R411 2006-000195 R-CEMENT 51ohm 5W 2006-001071 R-CEMENT 56ohm 5W

R412 2006-000195 R-CEMENT 51ohm 5W 2006-001071 R-CEMENT 56ohm 5W

R420 2003-000595 R-Metal Oxide;2W 240ohm,5% 2003-000650 R-Metal Oxide;2W 330ohm,5%

CN_EMC Do not use 2201-000291 C-Ceramic;500V 1nF

7-2-3 Different list for CDT - 920C

7-41 720C/920C

Page 76

Loc. No Code No. Description Specification Remark

CRT BH03-00047A CRT-COLOR M46QCY261X111(T4) SDI

BH03-00001A CRT-COLOR M46LQU280X01 Matsushita PBA UNIT BH94-00114A ASSY,PCB-SS MC19RO(920C),NOKIA,W/WIDE SDI

BH94-00114B ASSY,PCB-MS MC19RO(920C),NOKIA,W/WIDE Matsushita B/D ASSY BH98-00118A ASSY,PCB/MAIN-SS MC19RO(920C),NOKIA,W/WIDE SDI

BH98-00118B ASSY,PCB/MAIN-MS MC19RO(920C),NOKIA,W/WIDE Matsushita

BH98-00119A ASSY,PCB/VIDEO MC19RO(920C),NOKIA,W/WIDE SDI

BH98-00119B ASSY,PCB/VIDEO MC19RO(920C),NOKIA,W/WIDE Matsushita D/COIL BH27-00028A COIL-DEGAUSSING 320*355*1950mm,11.8mH

CRT GND ASSY

BH39-00054A CBF-HARNESS 1P,320mm,UL1015/3*0.16TA S/CABLE BH39-00070A CBF-SIGNAL CABLE 1830MM,15P/6P,8P,IVORY P/CORD BH39-10339E CBF-POWER CORD DET,SVT,125V/10A,IVORY USA

BH39-10007A CBF-POWER CORD DET,250V/10A,H05VV-F,LP-34,IVORY EUROPE TCO WIRE BH39-00069A CBF-HARNESS 1P,460MM,BLK,UL1015,AWG18

7-2-4 Others - 920C

7-42 720C/920C

Page 77

COLOR ADJUST CONTROL(JIG)

COLOR GAIN CONTROL

VIDEO

CUTOFF

CONTROL

HORIZONTAL BLANK

BRIGHTNESS CONTROL

HORIZONTAL BLANK

MUTE

AC INLET SOCKET

LINE FILTER

RECTIFIER

D3SBA60

AC INPUT 90-264VAC 60/50Hz

DEGAUSS OPERATION

D-COIL

SWITCHING TRANS

+25V

+14V

+7V

-14V

+14V_I

+80V

+210V

H-DRIVE

CRT HEATER

VERT OUT

SUSPEND

DEGAUSS

DDC-DATA DDC-CLK

S-RASTER

H-SYNC/

V-SYNC

OUT

SDA/SCL

CRYSTAL

12MHz

R G B

CRT

R G B

MICROPROCESSOR

KS88P6232N

D D C CONTROL 24LC21A

S-CORRECTION

LED

VIDEO PRE-AMP

M52748

(for 19")

KA2506

(for 17")

OSD KS2501

SDA/SCL

ERROR DETECT & FEED BACK

POWER SYNC

H-SYNC TRIGGER

PWM CONTROL &

SWITCHING FET

DP308P

D-SUB

R.G.B H-SYNC V-SYNC

INPUT

H-SYNC V-SYNC

POWER OFF CONTROL

VIDEO OUTPUT

VOLTAGE REGULATOR KA78R12

VOLTAGE REGULATOR KA7805

+5V

SOG

HOR.VER. OSC PROCESSING SAM9222G

H/V DRIVE

DYNAMIC FOCUS

HORIZONTAL FOCUS CIRCUIT

H-AFC

HOR. OUTPUT 2SC5584

H-DY

HORIZONTAL REGULATION CONTROL

HOR. REGULATION OUTPUT (PWM CONTROL)

REGULATION SENSER

HOR. DRIVE

S-CORRECTION

FBT

H/V OUTPUT

2SK2761

H/V REGULATION

ERROR FEEDBACK

X-RAY PROTECTOR

VERTICAL BLANKING GENERATOR

VERTICAL OUTPUT KA2142

V-DY

VERTICAL FOCUS CIRCUIT

+12V

HIGH VOLTAGE

SCREEN

FOCUS1, 2

H_LIN.

MOIRE

TILT

CLAMP

ACL

CONTROL BUTTON

OSD CALL/ENTER

POSITION/SIZE

PIN/TRAP

PARALLEL/ROTATION

CHOOSE OR ADJUST

MENU BUTTON

POWER BUTTON

CONTRAST

BRIGHTNESS

H-FLB V-FLB

SELECT

ACL

CLAMP

DDC-DATA

DDC-CLK

H-LIN

MUTE

SOG

VIDEO

OUTPUT VPS14 (for 19") LM2405 (for 17")

720C/920C 8-1

8-1 Block Diagram

Page 78

9 Wiring Diagram

720C / 920C 9-1

9-1 Wiring Diagram

CRT SOCKET

V FOCUS

H FOCUS

VIDEO PCB

+5 V

GND

+12V

+80V

+7V

123

+14V

567

GND 8

H-FLB

V-BLK

SCL

CLAMP

SDA

111213

ABL

SOG

CN102

1 2 3 4

Red-In

GND

Green-In

GND

Blue-In

GND

1 2 3 4

Red-In GND Green-In GND Blue-In

GND

CN101

Signal Cable

1 2 3 4

5 6 7

GND DDC 5V H-SYNC-IN V-SYNC-IN

DDC-CLK DDC-DATA

GND

S-RASTER

TILT –

FBT

MAIN PCB

+5 V

GND

+12V

+80V

+7V

123

+14V

567

GND

H-FLB

V-BLK

SCL

CLAMP

SDA

111213

ABL

SOG

CN204

123

567

CN208

GND

DDC 5V

H-SYNC-IN

V-SYNC-IN

DDC-CLK

DDC-DATA

GND

S-RASTER

TILT +

123

TILT –

TILT +

123

TILT

CN402

GND

SOG-IN

H-SYNC-IN

1 2 3

CN212

GND

SOG-IN

H-SYNC-IN

123

CN211

123

GND

AC INPUT

GND

AC INPUT

123

D-Coil POWER CORD

V FOCUS

Page 79

T601

C639

C609

C636

C638

L601

C604

D637

D608

10-1 Power Parts Schematic Diagram

720C / 920C 10-1

Page 80

R299

720C / 920C 10-2

10-2 MICOM Parts Schematic Diagram

Page 81

720C / 920C 10-3

 10-3 Horizontal/Vertical Processor Parts Schematic Diagram  

R265

C272

R262

Page 82

L405

R412R411

R476

CN409

C301

R404

R303

R302

R301

R304

R421

T401

R420

Q405

C402

C311

R308

L403

Q459

C309

R305

C413

C451

C310

C306

C452

C418

C422

R410

R307

D409

C457

Q458

720C/920C 10-4

10-4 Horizontal and Vertical Parts Schematic Diagram 

Page 83

R561 R562

R501

C530

L521

R523

R526

720C / 920C 10-5

10-5 High Voltage Parts Schematic Diagram

Page 84

720C 10-6-1

10-6-1 720C Video Parts Schematic Diagram

Page 85

920C 10-6-2

10-6-2 920C Video Parts Schematic Diagram

R121

4.7K 1/8W

R122 1K 1/8W

Q103

2N3904

C170 100nF 50V

R170 1K 1/8W

1/6W

R116

Page 86

720C/920C 10-7

10-7 Connector and Option Boards Parts Schematic Diagram

CN142

slcon4p

CN141

CN208

Page 87

1 (1)

Nokia Display Products Oy Customer Service February 2000

AFTER SALES CONCEPT CONCERNING NOKIA MODELS:

4 4 7 3 0 5 1 - 7 2 0 C 4 4 6 G 0 5 1 - 9 2 0 C

Dear Service Partner,

The regarded models are outsourced products designed and manufactured by SAMSUNG

according to Nokia’s

specification.

It has been agreed between Nokia and Samsung to comply with the After Sales concept described below.

1. Invoicing: Samsung Euro C.S. Head Office

will receive Nokia TPMs Invoice – at Nokia rate specifically agreed for this product – direct from Nokia TPM. Invoice is to be for Repair and Return (one way transport) only

Samsung Euro C.S. Head Office

will later instruct TPMs where to send their invoice.

Buffer Stock and Costs for Customer Swap Out is Nokia responsibility and will be invoiced to Nokia directly.

2. Reporting:

TPM will advise maintenance activities regarding these products using Nokia’s (or alternatively Samsung report if all the relevant data is in the report) standard report format but on separate worksheet!

Report to be sent to

Samsung Euro C.S. Head Office

on regular monthly basis with the invoice. A copy of the report to be sent to Nokia as well. Note the product codes: PROD_CODE 4473051 PROD_CODE 446G051

3. Practical matters:

- Samsung Euro C.S. Head Office

provides Nokia TPMs with Specific Components direct from Samsung at no charge. Samsung xxxx Service will later instruct TPMs how to re-order spare parts occasionally.

- In case of need of Specific Technical Support (repair clues etc.) TPM should contact Samsung as well.

----------------------------------------------------------------------------------------------------------

For any further consultation regarding the After Sales issue of the a.m. products, please contact:

At Nokia: Your After Sales contacts of respective NDP Sales Company / Office

At Samsung:

Samsung Euro C.S. Head Office Barry Sheppard Euro Technical Manager Stafford Park 12, Telford Shropshire TF3 38J, England Tel.: + 44 (0)1952 292262

Nokia 920C, 720C Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual