Nokia 3110 Non Serviceable Accessories

Programmes After Market Services

NHE–8/9 Series Transceivers

Non Serviceable Accessories

issue 2 11/97

NHE–8/9

PAMS

Non Serviceable Accessories

Technical Documentation

CONTENTS

Batteries for NHE–8/9 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Battery Pack BLJ–1 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Battery Pack BLJ–4 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Battery Pack BMH–1 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Battery Pack BMH–1V 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chargers for NHE–8/9 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fast & Light Charger ACH–6 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Universal Mobile Charger LCH–6 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fixed Mobile Charger LCM–1 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power Cable PCM–5 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Desktop Stand CGD–8 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Handsfree Headset Kit HDXK–8 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Headset Adapter HDA–4 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Headset Adapter HDC–2 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Data accessories for NHE–8/9 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Data Card DTP–2 ver II 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Infra Red Data Link JLC–1 and JLP–1 14. . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 2

issue 2 11/97

PAMS

NHE–8/9

Technical Documentation

Batteries for NHE–8/9

Battery Pack BLJ–1

The BLJ–1 is a Li–ion light battery back to provide an acceptable level of
performance in a package (ie including phone) weighing 146 g.

Non Serviceable Accessories

Product Code

Battery pack BLJ–1:

Specification

Dimensions (h x w x d):
Weight:
Capacity:

0670189 (Made in Japan)

120 x 42 x 10 mm
48 g
400 mAh

issue 2 11/97

Page 3

NHE–8/9

PAMS

Non Serviceable Accessories

Battery Pack BLJ–4

The BLJ–4 Li–ion extended battery pack provides the best compromise
between high performance and low weight. The extended package
(including phone) weighs 204 g.

Technical Documentation

Product Codes

Battery pack BLJ–4 :

Specification

Dimensions (h x w x d):
Weight:
Capacity:

0670190 (Made in Japan)

120 x 42 x 22 mm
106 g
1500 mAh

Page 4

issue 2 11/97

PAMS

NHE–8/9

Technical Documentation

Battery Pack BMH–1

The BMH–1 Ni–MH standard battery pack provides the best compromise
between weight, price and performance for the average user. The package
(i.e. including phone) weighs 183 g.

Non Serviceable Accessories

Product Codes

Battery pack BMH–1 :
Battery pack BMH–1 :
Battery pack BMH–1 :

Specification

Dimensions (h x w x d):
Weight:
Capacity:

0670194 (made in Czech)
0670198 (made in China)
0670199 (made by Nokia)

120 x 42 x 14 mm
85 g
550 mAh

issue 2 11/97

Page 5

NHE–8/9

PAMS

Non Serviceable Accessories

Battery Pack BMH–1V

The BMH–1V Ni–MH battery pack is identical to BMH–1 but with a vibrator
option build in. The package (including phone) weighs 187 g.

Technical Documentation

Product Codes

Battery pack BMH–1V:

Specification

Dimensions (h x w x d):
Weight:
Capacity:

0670200(made in Czech)

120 x 42 x 14 mm
89 g
550 mAh

Page 6

issue 2 11/97

PAMS

NHE–8/9

Technical Documentation

Chargers for NHE–8/9

Fast & Light Charger ACH–6

Extremely light, functionally designed fast & light charger charges your
phone battery quickly.

Plug the charger into a wall outlet and connect the connector to the bottom
of your phone. When not using the charger, you can wrap the cord around
it and attach the loose end to the slot on top.

The charging time is approximately 45 minutes for the 470 mAh battery.
Check the charging status on the phone display . Y ou can use your phone also
while charging.

Operating within voltage range 90 V...250 V AC (50 Hz...60 Hz), fast & light
charger is practically current independent in normal office and household
use. Like standard charger , fast & light charger is compatible with all battery
options and is available with different wall plugs.

Non Serviceable Accessories

The fast & light charger can also be used with basic stand and desktop stand.

ACH–6U ACH–6E ACH–6XACH–6A

S0001161

Product Codes

Fast

& light charger ACH–6U (USA plug):

Fast & light charger ACH–6E (Euro plug):
Fast & light charger ACH–6A (Austr. plug):

0675085
0675084

0675086

Fast & light charger ACH–6X (UK plug):
Output cable PCC–1 (supplied with ACH–6):

issue 2 11/97

0675087

0730076

Page 7

NHE–8/9

PAMS

Non Serviceable Accessories

Specification

Dimensions (h x w x d):
Weight:
Output cable length:
Mains plug type:
Output connectors:
Protection:

75 x 29 x 42 mm (without plug)
< 150 g
1950 mm
see picture

3.0 mm standard d.c. plug
output current limiting, max. 870 mA

output voltage limiting, max. 11 V
(unloaded)

Input voltage:

90 to 250 V

Universal Mobile Charger LCH–6

Technical Documentation

The universal mobile charger ensures your phone is always ready for use
wherever you travel. This small charger’s functional design fits well to most
car lighters and interiors.

A green light indicates that the cigarette lighter charger is ready for charging.
Check the charging status on the phone display . The input voltage can be 12
or 24 V d.c., negative grounding.

Universal mobile charger can be used with all car accessories provided for
your phone.

Avoid prolonged charging with universal mobile charger when the car engine
in not running; this may cause the battery of your car to drain. Note also that
in some cars the cigarette lighter plug is not provided with electricity if the
ignition is switched off. Verify that the green led light is lit.

Product Code

Universal mobile charger LCH–6:

Page 8

G0675076

0675076

issue 2 11/97

PAMS

NHE–8/9

Technical Documentation

Specification

Dimensions (h x w x d):
Weight:
Cable length:
Connectors

• input:

Protection:
Voltage

• input:

• output (nominal):

Nominal output current:

Non Serviceable Accessories

29 x 35 x 84 mm
< 70 g
465 mm curly cable

D 21/23 mm

• output:

3.0 mm standard d.c. plug
input fused, output current limit

11.3...35 V

10.3 V
780 mA

Charging into empty battery:

Fixed Mobile Charger LCM–1

The fixed mobile charger powers your phone from the car battery when the
ignition is switched on and leaves the cigarette lighter vacant.

You can use the fixed mobile charger in any vehicle with a 12 or 24 V d.c.
connection, negative grounding.

The charging time for the 470 mAh battery is only about 45 minutes.
Fixed mobile charger housing has a four pin connector for power cable, and

on the opposite end a connector for the output cable, which connects the
fixed mobile charger directly to the d.c. connector of your phone or to the
basic handsfree unit.

>= 300 mA

Product Code

Fixed mobile charger LCM–1:
Output cable PCC–1 (supplied with LCM–1):

issue 2 11/97

G0675077

0675077

0730076

Page 9

NHE–8/9

PAMS

Non Serviceable Accessories

Specification

Dimensions (h x w x d):
Weight:
Output cable length:
Protection:
Voltage

• input:

• output (nominal):

Output current nominal:
Charging into empty battery:

Power Cable PCM–5

Technical Documentation

27 x 36 x 65 mm
< 70 g
1950 mm
input fused, output current limit

11.3...32 V

10.3 V
780 mA
>= 300 mA

The power cable connects the fixed mobile charger, LCM–1, to the vehicle’ s
power supply. The red wire must be connected to the + voltage supply
controlled by the vehicle’s ignition key via the supplied fused connector . The
black wire must be attached to a good negative GND connection.

Product Code

Power cable PCM–5:

Specification

G0730058

0730058

Page 10

Weight:
Cable length

• red wire:

• black wire:

Max current via contacts:

74 ±5 g

2500 ±100 mm
2000 ±50 mm

1 A

issue 2 11/97

PAMS

NHE–8/9

Technical Documentation

Desktop Stand CGD–8

The desktop stand provides mounting place for both the phone and a spare
battery .

Charging order is the phone battery first, and then the spare battery. Check
the charging status of the phone battery on the phone display.

Compatible with all battery options, the desktop stand is used together with
the standard charger or fast & light charger.

Non Serviceable Accessories

Product Code

Basic stand CGD–8:

0675156 (Made in China)

issue 2 11/97

Page 11

NHE–8/9

PAMS

Non Serviceable Accessories

Specification

Dimensions (h x w x d):
Weight:
Connections:
Charge control:

42 x 76 x 103 mm
40 g

3.0 mm d.c. jack
cell voltage (peak or negative

change), time control, cell
temperature

Operation input voltage:
Max. input current:
Protection:

9...16 V
780 mA
no damage if short circuit in output

Handsfree Headset Kit HDXK–8

Technical Documentation

Compact and functional, headset kit HDXK–8 (headset adapter HDA–4,
headset HDC–2 and carrying case CBM–1 1 ) provides you with a convenient
handsfree facility which you can use anywhere.

Connect headset adapter HDA–4 to the bottom of your phone, and plug the
headset HDC–2 to the adapter.

In car use, you can connect the headset directly to the basic handsfree unit.
(The headset adapter is not required under this configuration.) When used
with external antenna adapter , this combination provides you with handsfree
operation, privacy and optimum reception quality. When the headset is
connected, the HF loudspeaker and microphone are disabled.

Headset Adapter HDA–4

The headset adapter provides connections between the headset, power
supply and the phone. The adapter plugs into the base of the phone.

Note: When using the headset adapter, connect your charger to the adapter if you need to
charge your phone.

Product Code

Headset adapter HDA–4:

Page 12

G0694029

0694042

issue 2 11/97

PAMS

NHE–8/9

Technical Documentation

Specification

Dimensions (h x w x d):
Weight:
Gain • microphone:

• earphone:

Sound pressure • microphone:

• earphone:

Level at headset connector:• microphone :

Headset Adapter HDC–2

• earphone:

Non Serviceable Accessories

28 x 29 x 13.3 mm
10 g

33.5 dB
0 dB

–16...+3 dBPa (0 dBPa = 94 dB spl)
0 dBPa...+23 dBPa

1.3...11.6 mV

16...220 mV

Product Code

Headset HDC–2:

Specification

Cord length :
Weight:
Microphone sensitivity:
Microphone directionality:
Microphone supply voltage:
Earphone rated/max input:
Earphone sound pressure:
Impedance

• microphone:

• earphone:

0694017

1500 ±50 mm
13 g
–46.5 ±5 dB (0 dB = 1 V/Pa at 1 kHz)
Omni–directional
5 V
1 mW/5 mW
106 ±5 dB (at 1 kHz, 1 mW)

max 2.2 kΩ at 1 kHz
32 ±7

Ω

issue 2 11/97

Page 13

NHE–8/9

PAMS

Non Serviceable Accessories

Data accessories for NHE–8/9

Data Card DTP–2 ver II

The DTP–2 ver II can be used with NHE–8/9.

Infra Red Data Link JLC–1 and JLP–1

The JLP–1 infra red link offers a wireless alternative for the data cable
between phone and the DTP–2. The link which uses infra red light as media
consists of two modules: JLP–1 which connects to the bottom system
connector of the phone, and JLC–1 which connects to the data cable IO
connector of the PCMCIA card having IR support.

Technical Documentation

JLC–1

JLP–1

Page 14

issue 2 11/97