Page 1
B ENGINE
A
ACC
SECTION ACC
ACCELERA T OR CONTROL SYSTEM
CONTENTS
ACCELERATOR CONTROL SYSTEM ...................... 2
Components ............................................................. 2
Removal and Installation .......................................... 3
REMOVAL FOR ADJUSTABLE ACCELERA TOR
PEDAL .................................................................. 3
REMOVAL FOR NON-ADJUSTABLE ACCEL-
ERATOR PEDAL ............ .......................................4
INSTALLATION .....................................................4
INSPECTION AFTER INSTALLATION ..................4
SERVICE DATA AND SPECIFICATIONS (SDS) ........5
Accelerator Control ...................................................5
ADJUSTABLE AND NON-ADJUSTABLE
ACCELERATOR PEDAL ....................................... 5
C
D
E
F
G
H
I
J
M
K
L
Revision: November 2005 2005 Pathfinder
ACC-1
Page 2
ACCELERATOR CONT ROL SYSTEM
ACCEL ER ATOR CON T ROL SYSTEM PFP:18005 Components EBS00M4J
Adjustable Accelerator Pedal
WBIA0628E
1. Adjustable accelera t or ped al ass em bl y 2. Adjustable brake pedal cab l e 3. Adjustable brak e pe dal cable lock
tab (part of the c able)
Revision: November 2005
ACC-2
2005 Pathfinder
Page 3
ACCELERATOR CONT RO L SYSTEM
Non-adjustable Accelerator Pedal
A
ACC
C
D
E
F
G
WBIA0629E
1. Non-adjustable accelerator pedal assembly
CAUTION:
● Before remova l an d in stallation, t he ad justable acce lerator and b rake ped als m ust be in t he front -
most position, if equipped. This is to align the base position of the accelerator and brake pedals.
● Do not disassemble the accelerator pedal assembly.
● Do not remove the accelerator pedal position sensor from the accelerator pedal bracket.
● Do not disassemble the accelerator pedal adjusting mechanism.
● Avoid damage from dropping the accelerator pedal assembly dur ing handling.
● Keep the accelerator pedal assembly away from water.
Removal and Installation EBS00KB3
REMOVAL FOR ADJUSTABLE ACCELERATOR PEDAL
1. Move the accelerator and brake pedals to the frontmost position.
2. Turn the ignition switch OFF and disconnect the negative battery terminal.
3. Disconnect the adjustable pedal electric motor electrical connector.
4. Disconnect the adjustable pedal electric motor memory electrical connector, if equipped.
5. Disconnect the accelerator position sensor electrical connector.
a. Pull the connector lock back to unlock the connector from the
accelerator pedal position sensor as shown.
b. Pull up on the connector to disconnect it from the accelerator
pedal position sensor as shown.
H
I
J
K
L
M
LBIA0333E
Revision: November 2005 2005 Pathfinder
ACC-3
Page 4
ACCELERATOR CONT ROL SYSTEM
6. Disconnect the adjustable brake pedal cable from the adjustable
accelerator pedal.
● Release the two lock tabs, then pull the adjustable brake
pedal cable to disconnect it from the adjustable accelerator
pedal.
7. Remove the two upper and one lower accelerator pedal nuts.
8. Remove the adjustable accelerator pedal assembly.
CAUTION:
● Do not disassemble the accelerator pedal assembly.
● Do not remo ve the accelerator pedal position sensor from the accelerator pedal bracket.
● Do not disassemble the accelerator pedal ad justing mechanism.
● Avoid damage from dropping the accelerator pedal assembly during handling.
● Keep the accelerator pedal assembly away from water.
LFIA0233E
REMOVAL FOR NON-ADJUSTABLE ACCELERATOR PEDAL
1. Disconnect the negative battery terminal.
2. Disconnect the acceler ator position sensor electrical connector.
a. Pull the connector lock back to unlock the connector from the
accelerator pedal position sensor as shown.
b. Pull up on the connector to disconnect it from the accelerator
pedal position sensor as shown.
3. Remove the two upper and one lower accelerator pedal nuts.
4. Remove the accelerator pedal assembly.
CAUTION:
● Do not disassemble the accelerator pedal assembly.
● Do not remove the accelerator pedal position sensor
from the accelerator pedal bracket.
● Avoid damage from dropping the accelerator pedal assembly during handling.
● Keep the accelerator pedal assembly away from water.
INSTALLATION
Installation is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
● Check that the accelerator pedal moves smoothly within the
specified range.
Accelerator pedal - total pedal
applied stroke “A”
: 48 mm (1.89 in)
LBIA0333E
● Check that the accelerator pedal smoothly returns to the original
position.
● Perform an electrical inspection of the accelerator pedal position
sensor. Refer to EC-650, "
DTC P2138 APP SENSOR" .
CAUTION:
When the ha rness c onnector of the acc elerator p edal position sensor is disconnected, perform ″Accelerator Pedal
Released Position Learning″. Refer to EC-88, "
Revision: November 2005
Accelerator Pedal Released Position Learning" .
ACC-4
LBIA0434E
2005 Pathfinder
Page 5
SERVIC E DA TA AND SPECIF ICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS ) PFP:00030
Accelerator Control EBS00KB4
ADJUSTABLE AND NON-ADJUSTABLE ACCELE RATOR PEDAL
Unit: mm (in)
LBIA0434E
Accelerator pedal - total pedal applied stroke “A” 48 (1.89)
A
ACC
C
D
E
F
G
M
H
I
J
K
L
Revision: November 2005 2005 Pathfinder
ACC-5
Page 6
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: November 2005
ACC-6
2005 Pathfinder
Loading...