New Holland TD 60D, TD 80D, TD 70D, TD 90D, TD 95D Owner's Manual
TD 60D
TD 70D
TD 80D
TD 90D
TD 95D
OPERATOR’S MANUAL
SECTION SUMMARY
1 -- General Information and Safety
2 -- Controls, Instruments and Operation
3 -- Field Operation
4 -- Lubrication and Maintenance
5 -- Fault Finding
6 -- Vehicle Storage
7 -- Accessories
8 -- Specifications
9 -- First 50--Hour Service Forms
10 -- Index
Electro-magnetic Interference (EMC)
This tractor complies strictly with the European Regulations on electro-magnetic emissions. However, interference may arise as a result of add-on equipment which may not
necessarily meet the required standards. As such interference can result in serious malfunction of the unit and/or create unsafe situations, you must observe the following:
• Ensure that each piece of non-New Holland equipment fitted to the tractor bears
the CE mark.
• The maximum power of emission equipment (radio, telephones, etc.) must not
exceed the limits imposed by the national authorities of the country where you use
the tractor.
• The electro-magnetic field generated by the add-on system should not exceed 24
V/m at any time and at any location in the proximity of electronic components.
Failure to comply with these rules will render the New Holland warranty null and void.
CONTENTS
Title Page
Section 1 -- General Information and Safety
To the owner 1--1................................................................................
Tractor identification 1--2.........................................................................
Ecology and the environment 1--5.................................................................
Safety precautions 1--6...........................................................................
Safety decals 1--12..............................................................................
International symbols 1--15.......................................................................
Section 2 -- Controls, Instruments and Operation
Safety covers and guards 2--2.....................................................................
Controls and instruments 2--4.....................................................................
Instrument panel 2--5............................................................................
Instrument console controls 2--11..................................................................
Right--hand side operating controls 2--12............................................................
Left--hand side operating controls 2--13.............................................................
Cab controls 2--15...............................................................................
Seats 2--16.....................................................................................
Cab 2--19......................................................................................
Cab air conditioning system 2--27..................................................................
Transmission with range gear -- 30 km/h (19 mph) 2--31...............................................
Transmission with range gear and shuttle-- 30 km/h (19 mph) 2--33.....................................
Transmission with creeper and shuttle-- 30 km/h (19 mph) 2--36........................................
Mechanically controlled four wheel drive 2--39.......................................................
Mechanically controlled differential lock 2--40........................................................
Towing the tractor 2--42..........................................................................
Loading the tractor onto a transporter 2--42.........................................................
Checks before using the tractor 2--43...............................................................
Section 3 -- Field Operation
Starting with thermostart the engine 3--3...........................................................
Power take--off 3--5..............................................................................
Hydraulic lift 3--18...............................................................................
Three--point linkage Cat. II 3--23...................................................................
Remote control valves 3--30......................................................................
Wheel track adjustment 3--32.....................................................................
Tyr es 3--39.....................................................................................
Tyre combinations 3--43..........................................................................
Ballasting 3--50.................................................................................
Static weight distribution 3-- 50.....................................................................
Section 4 -- Lubrication and Maintenance
Access for inspection and maintenance 4--4.........................................................
Lubrication and maintenance table 4--5.............................................................
Flexible maintenance 4--7........................................................................
When the warning light is on 4--9..................................................................
10--hour / daily service 4--10......................................................................
50--hour service 4--16............................................................................
300--hour service 4--19...........................................................................
600--hour service 4--24...........................................................................
900--hour service 4--24...........................................................................
1200--hour service 4--24..........................................................................
1200--hour or every 2 years service 4--27...........................................................
General maintenance 4--31.......................................................................
Electrical system 4--33...........................................................................
Recommendations for bodywork maintenance 4--40..................................................
Lubricant capacities and specifications 4--41........................................................
Section 5 -- Fault Finding
Introduction 5--1.................................................................................
Engine 5--2.....................................................................................
Electrical system 5--5............................................................................
Hydraulic system 5--6............................................................................
Three-point linkage 5--7..........................................................................
Brakes 5--8.....................................................................................
Cab 5--8.......................................................................................
Section 6 -- Vehicle Storage 6--1.................................................................
Section 7 -- Accessories
Beacon lamp 7--2................................................................................
Drawbars and towing attachments 7--3.............................................................
Hydralic trailer brake 7--9.........................................................................
Section 8 -- Specifications
General Dimensions 8--2.........................................................................
Weights 8--4....................................................................................
Engine specifications 8--5........................................................................
Timing 8--6.....................................................................................
Fuel system 8--6................................................................................
Lubrication 8--7.................................................................................
Cooling system 8--7..............................................................................
Transmission 8--7...............................................................................
Power take--off 8--8..............................................................................
Hydraulic system 8--8............................................................................
Three-point linkage 8--9..........................................................................
Front axle 8--9..................................................................................
Steering 8--10...................................................................................
4WD front axle 8--10.............................................................................
Brakes 8--11....................................................................................
Bodywork and driving position 8--11................................................................
Towing devices 8--11.............................................................................
Electrical system 8--12...........................................................................
Section 9 -- First 50--hour Service Forms 9--1.....................................................
Section 10 -- Index 10--1.........................................................................
1--1
SECTION 1
GENERAL INFORMATION AND SAFETY
TO THE OWNER
GENERAL
This Manual has been prepared to assist you in the
correct procedure for running--in, driving and
operating and for the maintenance of your new
tractor. Read this Manual carefully. Your tractor is
intended for use in normal and customary
agricultural applications.
If at any time you require advice concerning your
tractor, do not hesitate to contact your New Holland
dealer. He has factory trained personnel, genuine
manufacturers’ parts and the necessary equipment
to carry out all your service requirements.
Your tractor has been designed and built to give
maximum performance, economy and ease o f
operation under a wide variety of operating
conditions. Prior to delivery, the tractor was carefully
inspected, both at the factory and by your dealer to
ensure that it reaches you in optimum condition. To
maintain this condition and ensure trouble--free
operation, it is important that the routine services, as
specified in Section 4 of this Manual, are carried out
at the recommended intervals.
CLEANING THE TRACTOR
Your tractor is a state-of-the-art machine with
sophisticated controls. This should be borne in mind
when cleaning the tractor, particularly if using a high
pressure washer. Even though every precaution has
been taken to safeguard electrical components and
connections, the pressure generated by some of
these machines is such that complete protection
against water ingress cannot be guaranteed.
When using a high pressure washer, do not stand too
close to the tractor and avoid directing the jet at
electronic components, electrical connections,
breathers, seals, filler caps, etc. Never direct a cold
water jet at a hot engine or exhaust.
SAFETY
Pages 1--6 to 1--11 inclusive list the precautions to
be observed to ensure your safety and the safety of
others. Read the safety precautions and follow the
advice offered before operating the tractor.
FIRST 50 HOUR SERVICE
In Section 9, at the back of this Manual, you will find
the 50--hour service reports.
After you have operated the tractor for 50 hours, take
your tractor, together with this Manual, to your dealer.
He will then perform the factory recommended 50-hour service and complete the service report sheets
(pages 9--1 and 9--3). The first sheet (page 9--1) is the
dealer’s copy and should be removed by the dealer
after the service has been carried out. The second
sheet (page 9--3) is your copy of the service
performed. Ensure that you and the dealer sign
both copies.
SERVICE PARTS
It should be pointed out that genuine parts have been
examined and approved by the Company. The
installation and/or use of ‘non-genuine’ products
could have negative effects upon the design
characteristics of your tractor and thereby affect it’s
safety. The Company is not liable for any damage
caused by the use of ‘non--genuine’ parts and
accessories. Only genuine replacement parts should
be used. The use of non-genuine parts may
invalidate legal approvals associated with this
product.
It is prohibited to carry out any modifications to the
tractor unless specifically authorised, in writing, by
the After Sales Service department of the Company.
WARRANTY
Your tractor is warranted according to legal rights in
your country and the contractual agreement with the
selling dealer. No warranty shall, however, apply if
the tractor has not been used, adjusted and
maintained according to the instructions given in the
Operator’s Manual.
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--2
TRACTOR IDENTIFICATION
Serial numbers identify the tractor and its main components. The identification data must be supplied by the
dealer for requests for spare parts or service operations. Identification data is of fundamental importance in the
event of theft of the tractor. The location of the various identification data is shown below.
Frame identification data plate.
Frame and engine type
identification data plate.
Tractor frame number identification data
plate (stamped on the axle support )
TRE0080A
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--3
Frame and engine type identification data
plate (inside the cab).
Cab identification data plate.
TRE0061A
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--4
Tractor frame number
identification data plate
(stamped on the axle support)
Engine identification data plate
(stamped on engine body).
TRE0081A
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--5
ECOLOGY AND THE ENVIRONMENT
Soil, air and water are vital factors of agriculture and
life in general. Where legislation does not yet rule the
treatment of some of the substances which are
required by advanced technology, common sense
should govern the use and disposal of products of a
chemical and petrochemical nature.
The following are recommendations which may be of
assistance:
• Become acquainted with and ensure that you
understand the relative legislation applicable to
your country.
• Where no legislation exists, obtain information
from suppliers of oils, filters, batteries, fuels,
antifreeze, cleaning agents, etc., with regard to
their effect on man and nature and how to safely
store, use and dispose of these substances.
Agricultural consultants will, in many cases, be
able to help you as well.
HELPFUL HINTS
1. Avoid filling tanks using unsuitable containers or
inappropriate pressurised fuel delivery systems
which may cause considerable spillage.
2. In general, avoid skin contact with all fuels, oils,
acids, solvents, etc. Most of them contain
substances which can be harmful to your health.
3. Modern oils contain additives. Do not burn
contaminated fuels and/or waste oils in ordinary
heating systems.
4. Avoid spillage when draining off used engine
coolant mixtures, engine, gearbox and hydraulic
oils, brake fluids, etc. Do not mix drained brake
fluids or fuels with lubricants. Store them safely
until they can be disposed of in a proper way to
comply with local legislation and available
resources.
5. Modern coolant mixtures, i.e. antifreeze and
other additives, should be replaced every two
years. They should not be allowed to get into the
soil but should be collected and disposed of
safely.
6. Do not open the air-conditioning system yourself.
It contains gases which should not be released
into the atmosphere. Your dealer or air
conditioning specialist has a special extractor for
this purpose and will have to recharge the system
anyway.
7. Repair any leaks or defects in the engine cooling
or hydraulic system immediately.
8. Do not increase the pressure in a pressurised
circuit as this may lead to the components
exploding.
9. Protect hoses during welding as penetrating
weld splatter may burn a hole or weaken them,
causing the loss of oils, coolant, etc.
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--6
SAFETY PRECAUTIONS
A careful operator is the best operator. Most accidents
can be avoided by observing certain precautions. T o
help prevent accidents, read and take the following
precautions before driving, operating or servicing the
tractor. Equipment should be operated only by those
who are responsible and instructed to do so.
PRECAUTIONARY STATEMENTS
Throughout this Manual you will see text, preceded
by the words NOTE, ATTENTION, IMPORTANT,
CAUTION, WARNING or DANGER. Such text has
the following significance:
MACHINE SAFETY
NOTE: This text stresses a correct operating
technique or procedure.
ATTENTION: This text warns the operator of potential
machine damage if a certain procedure is not followed.
IMPORTANT: This text informs the reader of
something that he needs to know to prevent minor
machine damage if a certain procedure is not
followed.
PERSONAL SAFETY
CAUTION
The word CAUTION is used where a safe
behavioural practice, according to operating and
maintenance instructions and common safety
practices will protect the operator and others from
accident involvement.
WARNING
The word WARNING denotes a potential or hidden
hazard which could possibly cause serious injury. It
is used to warn operators and others to exercise due
care and attention to avoid a surprise accident with
machinery.
DANGER
The word DANGER denotes a forbidden practice in
connection with a serious hazard.
Failure to follow the CAUTION, WARNING and
DANGER instructions may result in serious bodily
injury or even death.
THE TRACTOR
1. Read the Operator’s Manual carefully before
using the tractor. Lack of operating knowledge
can lead to accidents.
2. Only allow properly trained and qualified persons
to operate the tractor.
3. To prevent falls, use the handrails and step plates
when getting on and off the tractor. Keep steps
and platform clear of mud and debris.
4. Replace all missing, illegible or damaged safety
decals.
5. Keep safety decals free of dirt or grime.
6. Do not permit anyone but the operator to ride on
the tractor unless a passenger seat is fitted.
There is no safe place for extra passengers
otherwise.
7. Keep children away from the tractor and farm
machinery at all times.
8. Do not modify or alter or permit anyone else to
modify or alter the tractor or any of its
components or any tractor function without first
consulting your dealer.
9. Install all guards before starting the engine or
operating the tractor.
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--7
DRIVING THE TRACTOR
1. Always sit in the driver’s seat while starting or
driving the tractor.
2. When driving on public roads, have
consideration for other road users. Pull in to the
side of the road occasionally to allow any
following traffic to pass. Do not exceed the legal
speed limit set in your country for agricultural
tractors.
3. Use a rotating beacon when driving on public
roads to indicate that the vehicle is slow moving
and is a possible hazard.
4. Dip the tractor lights when meeting a vehicle at
night. Make sure the lights are adjusted to
prevent blinding the driver of an oncoming
vehicle.
5. Reduce speed before turning or applying the
brakes. Brake both wheels simultaneously when
making an emergency stop. Ensure that both
brake pedals are locked together when travelling
at road speeds or when on public roads to ensure
correct operation of trailer brakes, balanced
operation of the tractor brakes and four wheel
braking (4WD tractors only).
6. Use extreme caution and avoid hard application
of the tractor brakes when towing heavy loads at
road speeds.
7. Keep the tractor in the same gear when going
downhill as would be used when going uphill. Do
not coast or freewheel down hills.
8. For safe operation any towed vehicle whose total
weight exceeds that of the towing tractor must be
equipped with a braking system that complies
with the legal requirements of that country.
9. Never apply the differential lock when turning.
When engaged, the differential lock will prevent
the tractor from turning.
10. Always check overhead clearance, especially
when transporting the tractor. Watch where you
are going, especially at row ends, on roads and
around trees and low overhanging obstacles.
1 1. Toavoid overturns, drive the tractor with care and
at speeds compatible with safety, especially
when operating over rough ground, when
crossing ditches or slopes and when turning
corners.
12. Use extreme caution when operating on steep
slopes.
13. If the tractor becomes stuck or the tyres are
frozen to the ground, reverse the tractor out to
prevent overturning.
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--8
OPERATING THE TRACTOR
1. Apply the parking brake, place the P.T.O. control
in the ‘OFF’ position, the lift control lever in the
down position, the remote control valve levers in
the neutral position and the transmission levers
in neutral before starting the tractor.
2. Do not start the engine or operate controls (other
than externally located hydraulic lift or P.T.O.
switches, if fitted) while standing beside the
tractor. Always sit in the tractor seat when
starting the engine or operating the controls.
3. Do not bypass the transmission and P.T.O.
neutral start switches. Consult your authorised
dealer if your neutral start controls malfunction.
Use jump leads only in the recommended
manner. Improper use can result in a tractor
runaway.
4. Avoidaccidental contact with the gear shift levers
while the engine is running. Unexpected tractor
movement can result from such contact.
5. Do not get off the tractor while it is in motion.
6. If the power steering or engine ceases operating,
stop the tractor immediately as the tractor will be
more difficult to control.
7. Before leaving the tractor, park the tractor on
level ground, apply the parking brake, lower
attached implements to the ground, disengage
the P.T.O. and stop the engine.
8. Do not park the tractor on a steep incline.
9. The cab is designed to provide the minimum
noise level at the operator’s ears and meets or
exceeds applicable standards in this respect.
However, noise (sound pressure level) in the
workplace can exceed 85 dB(A) when working
between buildings or in confined spaces, with
cab windows open. Therefore, it is
recommended that operators wear suitable ear
protectors when operating in high noise level
conditions.
10. Do not run the tractor engine in an enclosed
building without adequate ventilation. Exhaust
fumes are toxic and can cause death.
1 1. Pull only from the pick-up hitch, swinging
drawbar or the lower link drawbar in the lowered
position. Use only a drawbar pin that locks in
place. Pulling from the tractor rear axle or any
point above the axle may cause the tractor to
overturn.
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--9
12. Always select Position Control when attaching
equipment and when transporting equipment. Be
sure hydraulic couplers are properly mounted
and will disconnect safely in case of accidental
detachment of the implement.
13. If the front end of the tractor tends to rise when
heavy implements are attached to the
three--point hitch, install front end or front wheel
weights. Do not operate the tractor with a light
front end.
14. Engage the clutch slowly when driving out of a
ditch, gully or up a steep hillside. Disengage the
clutch promptly if the front wheels rise off the
ground.
15. Ensure any attached equipment or accessories
are correctly installed, are approved for use with
the tractor, do not overload the tractor and are
operated and maintained in accordance with the
instructions issued by the equipment or
accessory manufacturer.
16. Remember that your tractor, if abused or
incorrectly used, can be dangerous and become
a hazard both to the operator and to bystanders.
Do not overload or operate with attached
equipment which is unsafe, not designed for the
particular task or is poorly maintained.
17. Do not leave equipment in the raised position
when the vehicle is stopped or unattended.
18. Do not drive equipment near open fires.
19. Always wear a protective mask when working
with toxic spray chemicals. Follow the directions
on the chemical container.
OPERATING THE P.T.O.
1. When operating PTO- driven equipment, shut off
the engine, switch off the PTO and wait until the
PTO stops before getting off the tractor and
disconnecting the equipment.
2. Do not wear loose clothing when operating the
power take-off or especially when near rotating
equipment.
3. When operating stationary PTO-driven
equipment, always apply the tractor parking
brake and block the rear wheels front and back.
4. To avoid injury , do not clean, adjust, unclog or
service PTO driven equipment when the tractor
engine is running. Ensure that the PTO is
switched off.
5. Make sure the PTO guard is in position at all
times and always replace the PTO cap when the
PTO is not in use.
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--10
SERVICING THE TRACTOR
1. The cooling system operates under pressure
which is controlled by the expansion tank cap. It
is dangerous to remove the cap while the system
is hot. Always turn the cap slowly to the first stop
and allow the pressure to escape before
removing the cap entirely. Never remove the cap
from the top of the radiator unless the expansion
tank pressure cap has first been removed.
2. Do not smoke while refuelling the tractor. Keep
any type of open flame away.
3. Keep the tractor and equipment, particularly
brakes and steering, maintained in a reliable and
satisfactory condition to ensure your safety and
comply with legal requirements.
4. To prevent fire or explosion, keep open flames
away from battery or cold weather starting aids.
To prevent sparks which could cause explosion,
use jumper cables according to instructions.
5. Do not attempt to service the air conditioning
system. It is possible to be severely frost bitten or
injured by escaping refrigerant. Special
equipment and instruments are required to
service the air conditioning system. See your
authorised dealer for service.
6. Stop the engine before performing any service
on the tractor.
7. Hydraulic fluid and fuel oil in the injection system
operate under high pressure. Escaping hydraulic
fluid or fuel oil under pressure can penetrate the
skin causing serious injury.
Unqualified persons should not remove or
attempt to adjust a pump, injector, nozzle or any
other part of the fuel injection or hydraulic
systems. Failure to follow these instructions can
result in serious injury.
• Do not use your hand to check for leaks. Use a
piece of cardboard or paper to search for leaks.
• Stop the engine and relieve pressure before
connecting or disconnecting lines.
• Tighten all connections before starting the
engine or pressurising lines.
• If fluid is injected into the skin obtain medical
attention immediately or gangrene may result.
8. Do not modify or alter or permit anyone else to
modify or alter the tractor or any of its
components or any tractor function without first
consulting an authorised dealer.
9. Continuous long term contact with used engine
oil may cause skin cancer. Avoid prolonged
contact with used engine oil. Wash skin promptly
with soap and water.
10. Keep equipment clean and properly maintained.
1 1. Dispose of all drained fluids and removed filters
properly.
12. Tractor wheels are very heavy. Handle with care
and ensure, when stored, that they can not topple
and cause injury.
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--11
DIESEL FUEL
1. Under no circumstances should gasoline,
alcohol or blended fuels be added to diesel fuel.
These combinations can create an increased fire
or explosive hazard. In a closed container such
as a fuel tank these blends are more explosive
than pure gasoline. Do not use these blends.
2. Never remove the fuel cap or refuel with the
engine running or hot.
3. Do not smoke while refuelling the tractor or when
standing near fuel. Keep any type of open flame
away.
4. Maintain control of the fuel filler pipe nozzle when
filling the tank.
5. Do not fill the fuel tank to capacity. Fill only to the
bottom of the filler neck to allow room for
expansion.
6. Wipe up spilled fuel immediately.
7. Always tighten the fuel tank cap securely.
8. If the original fuel tank cap is lost, replace it with
an approved cap. A non--approved cap may not
be safe.
9. Never use fuel for cleaning purposes.
10. Arrange fuel purchases so that summer grade
fuels are not held over and used in the winter.
SAFETY CAB
Your tractor is equipped with a safety cab which must
be maintained in a serviceable condition. Be careful
when driving through doorways or working in
confined spaces with low headroom.
1. Do not modify, drill, weld or alter the safety cab in
any way. Doing so could render you liable to legal
prosecution in some countries.
2. Never attempt to straighten or weld any part of
the main frame or retaining brackets which have
suffered damage. By doing so you may weaken
the structure and endanger your safety.
3. Do not secure any parts on the main frame or
attach your safety cab with other than the special
high tensile bolts and nuts specified.
4. Never attach chains or ropes to the cab or main
frame for pulling purposes.
5. Never take unnecessary risks even though your
safety cab affords you the maximum protection
possible.
WHENEVER YOU SEE THIS SYMBOL IT MEANS: ATTENTION!
BECOME ALERT! YOUR SAFETY IS INVOL VED!
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--12
SAFETY DECALS
The decals reproduced on the following pages were installed on your tractor in the positions indicated in the drawings
below. They are intended for your safety and for those working with you. Please take this Manual and walk around
your tractor, noting the location of the decals and their significance. Review the decals and operating instructions
detailed in this Manual with the machine operators. Keep the decals clean and legible. If they become damaged or
illegible, obtain replacements from your authorised dealer .
2
4
5
7
6
3
3
1
1
TRE0004A
TRE0023A
TRE0062A
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--13
1. Location: On the
left--hand upright of
ROPS and inside the
cabandalsoonthe
filter drier under the
bonnet.
Non--compliance with
the instructions provided
in this manual can lead to
serious injury to the operator or bystanders.
Read the instructions on
pages 1--6 to 1--11
inclusive.
2. Location: On the
right--hand lift rod
GENERAL WARNING:
Observe and respect the
indications on the safety
decals when this symbol is
present.
3. Location: On the
right--hand upright of
ROPS and inside the
cab.
If the tractor should
overturn, hold the
steering wheel tightly. Do
not attempt to jump out of
the cab.
5. Location: Left and
right--hand side of the radiator.
WARNING: Pressurised
cooling system. Allow to cool
then remove cap carefully.
Use a cloth to slowly unscrew
the cap and release the
pressure before completely
removing the cap.
4. Location: Left and right-hand sides of the radiator.
To avoid serious injury, keep
hands and clothing away
from the rotating fan, belts
and any other rotating parts.
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--14
7. Location: Front of transmission console (less cab tractors only)
-- all countries.
Do not grasp the transmission levers when mounting the tractor. Use only
the hand holds provided.
7. Location: Front of transmission console (tractors with cab only)
-- all countries.
Do not grasp the transmission levers when mounting the tractor. Use only
the hand holds provided.
6. Location: Tool box lid.
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--15
INTERNATIONAL SYMBOLS
As a guide to the operation of your tractor, various universal symbols have been utilised on the instruments,
controls, switches, and fuse box. The symbols are shown below with an indication of their meaning.
Headlamp
dipped beam
Stop
lamps
Thermostart
starting aid
Alternator
charge
Fuel level
Engine speed
(rev/min x 100)
Hours recorded
Engine oil
pressure
Engine coolant
temperature
Tractor lights
Headlamp
main beam
Work lamps
Automatic
fuel shut-off
Coolant
level
Turn signals
Turn signals
--one trailer
Turn signals
--two trailers
Heater fan
Front windscreen
wash/wipe
Air filter
blocked
Parking
brake
Rear
windscreen
wash/wipe
Horn
Roof
beacon
Radio
Keep alive
memory
Heater
temperature
control
Air conditioner
Warning!
Warning!
Corrosive
substance
P. T. O.
Transmission
in neutral
Creeper
gears
Slow or
low setting
Fast or high
setting
Ground
speed
FWD
engaged
FWD
disengaged
Variable
control
Differential
lock
Rear axle oil
temperature
Transmission
oil pressure
Pressurised!
Open carefully
Malfunction!
See Operator’s
Manual
Position
Control
Draft
Control
Hitch disabled
% slippage
Hitch raise
(rear)
Hitch lower
(rear)
Hitch height
limit (rear)
Remote
valve extend
Remote
valve retract
Remote
valve float
Hydraulic and
transmission
filters
Accessory
socket
Implement
socket
Hazard
warning lights
KAM
N
Malfunction!
(alternative
symbol)
Trailer
brake
Hitch height
limit (front)
Brake fluid
level
SECTION 1 -- GENERAL INFORMATION AND SAFETY
1--16
TRACTOR NOISE LEVEL INFORMATION SHEET
In compliance with DPR no. 212 enclosure 8 section II incorporating directive 77/311/EEC, the noise levels
for tractors fitted with tyres covered by the Use and Maintenance Manual are as specified below.
TRACTORS WITH ROLL BARS 2/4WD
Maximum noise level at
steering whee
l
dB (A)
Model
30 km/h
(19 mph)
40 km/h
(25 mph)
TD60D 85
TD70D 85
TD80D 86
TD90D 85
TD95D 84
TRACTORS WITH CABS 2/4WD
Maximum noise level at
steering wheelw
ithcab
d
oors
and windows closed
Model
dB (A)
30 km/h
(19 mph)
40 km/h
(25 mph)
TD60D 80
TD70D 80
TD80D 80
TD90D 80
TD95D 80
TRACTORS WITH CABS 2/4WD
Maximum noise level at
steering wheelw
ithcab
d
oors
and windows open
Model
dB (A)
30 km/h
(19 mph)
40 km/h
(25 mph)
TD60D 83
TD70D 80
TD80D 82
TD90D 83
TD95D 84
WARNING -- If the noise level during continuous use
reaches or exceeds 85 dB (A), the user must adopt
suitable precautions.
2-- 1
SECTION 2
CONTROLS, INSTRUMENTS AND OPERATION
INTRODUCTION
This Operator’s Manual has been produced to
provide the user with practical information,
documents and instructions about the correct
procedure for running in, driving, operating and
maintaining the new tractor.
The Manual is subdivided into 10 sections. The main
index is at the end of the Manual (Section 10).
Read and refer to this Manual carefully, and always
keep it in a convenient place so that you can refer to
it whenever necessary.
If you should at any time need information and advice
about using your tractor, please contact your
authorised dealer.
The dealer can provide skilled personnel, genuine
spare parts and the necessary equipment to carry
out your service requirements.
All the data provided in this Manual is subject to
product modifications. Weights and measures are to
be considered approximate figures and the
illustrations do not necessarily show tractors with
standard fittings.
For precise information on specific tractor models
and versions, please contact your authorised dealer.
The Company is engaged in a continuous process of
product development and improvement and
therefore reserves the right to change the
specifications, components and prices of the product
itself at any time, without prior notice.
In this Manual, the ”left--hand” and ”right--hand” parts
of the tractor are as seen from the driver’s seat,
facing forward.
The necessary precautions to guarantee the
personal safety of the operator and others are listed
and described under the heading ‘WORKING
SAFELY’ at the beginning of the Manual. Read and
follow the information provided BEFORE using the
tractor.
SECTION 2 -- CONTROLS, INSTRUMENTS AND OPERATION
2-- 2
SAFETY COVERS AND GUARDS
The tractor is fitted with covers and guards for the
personal safety of the operator and other people
when working.
CAUTION
Before starting the engine or using the tractor,
always check that all safety covers and guards are
correctly fitted.
BONNET (HOOD) -- Fig. 1
The hood (1) covers the engine’s moving parts.
It must be closed before the engine is started and the
tractor is used.
1
1
FA N GUARD -- Fig. 2
Both sides of the fan have guards (1). The guard
shown protects the left--hand side of the fan.
TRE0022A
1
2
STARTER MOTOR COVER -- Fig. 3
The cover (1) protects the electro--magnetic
contacts of the starter motor from accidental contact.
It must always be in place when the batteries are
connected to the electrical system.
The cover also protects the battery from possible
damage and the electrical connections from possible
accidental contact.
TRE0070A
1
3
SECTION 2 -- CONTROLS, INSTRUMENTS AND OPERATION
2-- 3
TRACTOR POWER TAKE --OFF GUARD -Fig. 4
The guard (1) covers the power take--off shaft.
To facilitate shaft replacement, loosen screws (2)
and remove the guard.
CAUTION
The guard must never be removed when the tractor
is being used and must never be modified.
1
2
TRE0016A
4
POWER T AKE-- OFF SHAFT SAFETY CAP -Fig. 5
The cap (1) must always be fitted on the power
take--off shaft when it is not connected to an
implement.
Replace it correctly when the power take--off is not
in use.
CAUTION
Check that all guards and covers are correctly fitted
before using the tractor.
1
TRE0016A
5
PIVOTING POWER TAKE--OFF GUARD -Fig. 6
The guard (1) protects the power take--off shaft.
NOTE: T o facilitate connection of the tractor
transmission shaft / implement, lift the guard (1).
Once connected, return the guard to the safety
position.
CAUTION: The guard must never be
removed when the tractor is being used and
must never be modified.
TRE0801A
1
6
SECTION 2 -- CONTROLS, INSTRUMENTS AND OPERATION
2-- 4
CONTROLS AND INSTRUMENTS -- POSITION AND FUNCTION
The position and function of the controls and
instruments on your tractor are described in the
following pages.
The controls have been sub--divided into groups and
are described as follows:
-- Instrument panel and console controls
-- Instrument console (rear hood) controls
-- Operating controls, right--hand side.
-- Operating controls, left--hand side.
-- Foot pedal and foot plate controls.
-- Cab controls.
CAUTION
Do not use the tractor if you are not fully acquainted
with the position and operation of all the tractor
controls.
SECTION 2 -- CONTROLS, INSTRUMENTS AND OPERATION
2-- 5
INSTRUMENT PANEL
1
2
3 4
1
TRE0027A
7
1. Warning and indicator lights
These lights illuminate to indicate a particular
operation or to attract your attention.
2. Engine coolant temperature gauge
3. Proofmeter / tachometer
Hourmeter, engine speed counter, tachometer.
4. Fuel gauge
SECTION 2 -- CONTROLS, INSTRUMENTS AND OPERATION
2-- 6
1 2 3 4
5
6 7
TRE0073A
8
1. Tractor left turn indicator (green)
Flashes in unison with the tractor left turn indicators.
2. Side lights indicator (green)
Lights up when the side lights are switched on.
3. Main beam indicator (blue)
The light illuminates when the headlights are on main
beam.
4. Water in fuel indicator (green)
The light illuminates to indicate that the fuel in the
filter bowl is clogged. Clean the filter, as described in
section 4, operation 8.
5. Dry air filter clogged warning light (yellow)
The light comes on when the air filter cartridge is
partially or totally clogged. Clean the filter, as
described in section 4, operation 6.
6. First trailer turn indicator lights (green)
Flashes in unison with the tractor turn indicators, if
connected.
7. Second trailer turn indicator lights (green)
Flashes in unison with the tractor turn indicators, if
connected.
SECTION 2 -- CONTROLS, INSTRUMENTS AND OPERATION
2-- 7
1 2 3 4 5
6
TRE0072A
9
1. Low engine pressure indicator (red)
The light should go out a few seconds after the
engine is started.
If it stays on when the engine is running, switch off the
engine and look for the cause of the problem. If the
light remains on, particularly when the tractor is
moving, contact your dealer. When the engine is
warmed up and running at minimum speeds, with the
tractor stationary, the light may illuminate, even if no
faults are present.
2. Battery charging system malfunction light
(red)
It should go out once the engine starts.
3. Low front brake fluid level indicator.
Comes on when the fluid drops below “MIN” level.
Check periodically that the light is working properly.
With the ignition key in the first position, press the lid
on the brake fluid reservoir; the indicator should light
up.
4. Handbrake ON light (red)
With the ignition key turned on, the light comes on
when the handbrake is applied.
5. Tractor right turn indicator (green)
Flashes in unison with the tractor right turn
indicators.
6. Not used on this tractor range.
SECTION 2 -- CONTROLS, INSTRUMENTS AND OPERATION
2-- 8
1. Proofmeter / tachometer -- Fig. 10
This shows engine speed and total time to a
maximum of six digits. The figures on the black
background show total working hours and those on
the red background (extreme right) tenths of an hour.
The green and blue sectors show the engine rev/min
reached at standard power take--off speeds of 540,
540E and 1000 rev/min.
TRE0076A
10
2. Engine coolant temperature gauge -- Fig. 11
-- Green area = normal temperature.
-- White area = temperature too low.
-- Red area = engine overheating
In this case, slow the engine to minimum revs (do not
stop it) and, if the light stays on, have the cooling
system checked.
TRE0075A
11
3. Fuel gauge -- Fig. 12
It shows the fuel level in the tank.
When the tank is full, the needle is at the extreme
right.
When the fuel level falls below
1
/4, the needle moves
into the red area.
TRE0074A
12
Loading...