Installation Guide
1. Register With the NETGEAR Insight App
Use the NETGEAR Insight App to register your switch.
1. On your iOS or Android mobile device, visit the app store, search for
NETGEAR Insight, and download the latest app.
PoE Access Point
PoE IP camera
GS310TP switc h
Internet
Router
ReadyNAS
NETGEAR® S350 Series 8-Port Gigabit Ethernet
Smart Managed Pro Switch (GS308T)
NETGEAR® S350 Series 8-Port Gigabit PoE+
Ethernet Smart Managed Pro Switch with 2 SFP
Ports (GS310TP)
Package Contents
• Switch model GS308T or GS310TP
• GS308T power adapter (varies by region) or
GS310TP adapter with detatchable power cord (varies by region)
• Installation guide
Note: For more information, see the hardware installation guide which you can
download from https://www.netgear.com/support/.
2. Open the NETGEAR Insight app.
3. If you did not set up a NETGEAR account, tap Create NETGEAR Account and
follow the onscreen instructions.
4. Enter the email address and password for your account and tap LOG IN.
5. Tap + in the upper right corner.
6. Either use the camera on your phone to scan the serial number bar code
located on the bottom of the switch, or type in the serial number.
7. Tap Go.
8. Tap View Device to add the switch to a network.
The switch is registered and added to your account.
2. Connect the Switch
GS308T switch
Internet
Desktop
IP camera
Laptop
ReadyNAS
Sample Connections
Router
Gaming console
Desktop
Smart TV
PoE VoIP/Video
PoE Phone
Sample Connections
Desktop
Desktop
3. Check the PoE Status (GS310TP Only)
PoE+ power is provided by the GS310TP switch on ports 1-8. The switch can
supply up to 30W PoE+ (IEEE 802.3at) to each port, with a maximum PoE power
budget of 55W across all active PoE+ ports.
The PoE Max LED indicates the status of the PoE budget on the switch:
• Off. Sufcient (more than 7W of) PoE power is available.
• Solid yellow. Less than 7W of PoE power is available.
• Blinking yellow. At least once during the previous two minutes, less than 7W
of PoE power was available.
4. Discover the IP Address
An IP address is required to congure your switch. The switch gets an IP
address from a DHCP server (such as your router) by default. If your switch is not
connected to a DHCP server, use the default IP address: 192.168.0.239.
Note: Make sure that you are using the latest version of the app.
1. On your mobile device, connect with WiFi to the same router as the switch.
2. Open the NETGEAR Insight app and log in to your account.
The current IP address of the switch is displayed.
Continued on the other side.
5. Congure the Switch
We recommend that you use a web browser on a computer or tablet to congure
the switch.
Note: If your computer is a Mac, use the NETGEAR Switch Discovery Tool, as
described in the following section.
1. Open a web browser from a computer or tablet connected to the same
network as your switch.
You can use a WiFi or wired connection.
2. Enter the IP address of the switch.
3. Enter the password.
The default password is password. We recommend that you change the
password to a more secure password.
4. Click the Login button.
Other Discovery and Conguration Methods
Note: If you cannot discover or congure the switch, you might need to
temporarily disable the rewall, Internet security, or antivirus programs. Make
sure to reenable these security services after you discover and congure the
switch.
PoE Considerations
The PoE and PoE+ power supplied by the GS310TP switch is prioritized in
ascending port order (from port 1 to port 8), with a total power budget of 55
watts with a 67.5 watt power adapter. If the power requirements for the attached
powered devices (PDs) exceed the total power budget of the switch, the PD
on the highest-numbered port is disabled to make sure that the PDs that are
connected to the higher-priority, lower-numbered ports are supported rst.
Just because a PD is listed as an 802.3at PoE powered device does not
necessarily mean that it requires the maximum power limit of the specication.
Many PDs require less power, allowing all eight PoE+ ports to be active
simultaneously.
The following table describes the PoE and PoE+ classes and switch allocations.
Support
Thank you for purchasing this NETGEAR product. You can visit
https://www.netgear.com/support/ to register your product, get help, access the
latest downloads and user manuals, and join our community. We recommend
that you use only ofcial NETGEAR support resources.
Si ce produit est vendu au Canada, vous pouvez accéder à ce document en
français canadien à https://www.netgear.com/support/download/.
(If this product is sold in Canada, you can access this document in Canadian
French at https://www.netgear.com/support/download/.)
For regulatory compliance information including the EU Declaration of
Conformity, visit https://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
Do not use this device outdoors. If you connect cables or devices that are
outdoors to this device, see https://kb.netgear.com/000057103 for safety and
warranty information.
The NETGEAR Switch Discovery Tool and the Smart Control Center Utility let you
discover the IP address and congure the switch.
• NETGEAR Switch Discovery Tool. You can use a Mac or a 64-bit Windows-
based computer that is on the same network as the switch. You can use a
WiFi or wired connection. When you discover the switch, this tool provides
access to the local browser interface to congure the switch. To download
the NETGEAR Switch Discovery Tool, visit
www.netgear.com/support/product/netgear-switch-discovery-tool.aspx.
• Smart Control Center Utility. You can use a Windows-based computer that
is on the same network as the switch. This utility requires Adobe Air. If Adobe
Air is not detected during Smart Control Center Utility installation, you are
prompted to allow Adobe Air to be installed. To download this utility, visit
www.netgear.com/support/product/SCC.
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo
November 2018
are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.
Device
Class
Calculated with the maximum cable length of 328 feet (100 meters). Shorter cable lengths
*
will provide power closer to the power reserved by the switch.
Standard Class
Description
0 PoE and PoE+ Default power
(full)
1 PoE and PoE+ Very low power 4.0W 0.44W–3.84W
2 PoE and PoE+ Low power 7.0W 3.84W–6.49W
3 PoE and PoE+ Mid power 15.4W 6.49W–12.95W
4 PoE+ only High power 30.0W 12.95W–25.5W
Power
Reserved by
the Device
15.4W 0.44W–12.95W
Power
Delivered to
the Device*
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
NETGEAR INTL LTD
Building 3, University Technology Centre
Curraheen Road, Cork, Ireland
Loading...