Netgear EX7700 User Manual
Nighthawk X6 AC2200
Tri-Band WiFi Range Extender
User Manual
Model EX7700
July 2018
202-11897-02
350 E. Plumeria Drive
San Jose, CA 95134
USA
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
Support
Thank you for purchasing this NETGEAR product.You can visit www.netgear.com/support to register your
product, get help, access the latest downloads and user manuals , and join our comm unity.We recommend that
you use only official NETGEAR support resources.
Conformity
For the current EU Declaration of Conformity, visit http://kb.netgear.com/app/answers/detail/a_id/11621.
Compliance
For regulatory compliance information, visit http://www.netgear.com/about/regulatory.
See the regulatory compliance document before connecting the power supply.
Trademarks
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. An y non_NETGEAR
trademarks are used for reference purposes only.
2
Contents
Chapter 1 Overview
Unpack Your Extender............................................................................................6
LEDs......................................................................................................................7
Back Panel.............................................................................................................9
When to Use Your Extender.................................................................................10
How the Extender Works.....................................................................................10
Chapter 2 Get Started
Install the WiFi Extender......................................................................................12
Place the Extender and Apply Power..............................................................12
Connect to an Existing WiFi Network..............................................................12
Use the Extender in Access Point Mode..............................................................15
Connect a Device to the Extender Network.........................................................16
Connect a Device to the Extender Network Using WiFi..................................16
Connect a Device to the Extender Network Using WPS.................................17
Connect an Ethernet-Enabled Device to the Extender....................................17
Log In to the Extender After Installation...............................................................17
Run Smart Setup Installation...............................................................................18
Connect With WPS.....................................................................................12
Connect With the NETGEAR Installation Assistant....................................14
Chapter 3 Extender Network Settings
Enable or Disable One WiFi Name......................................................................20
Enable or Disable Smart Connect........................................................................21
View Connected Devices.....................................................................................22
View WiFi Settings...............................................................................................23
Change the WiFi Network Name..........................................................................23
Turn Off the SSID Broadcast to Create a Hidden Network..................................24
Disable or Enable the WiFi Radios.......................................................................25
Change the WiFi Speed.......................................................................................26
Use WPS to Add a Computer to the Extender’s WiFi Network............................26
Use WPS With the Push Button Method.........................................................27
Use WPS With the PIN Method.......................................................................28
Deny Access to a Computer or WiFi Device........................................................28
Set Up an Access Schedule................................................................................29
Change the Extender’s Device Name..................................................................30
Set Up the Extender to Use a Static IP Address..................................................31
Configure a Router With Adv anced MAC Settings to Work with Your Extender....32
Chapter 4 Maintain and Monitor the Extender
Change the Extender Login User Name and Password.......................................35
Turn Password Protection Off and On..................................................................35
3
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
Recover a Forgotten User Name or Password.....................................................36
Automatically Adjust for Daylight Saving Time.....................................................37
Manually Set the Extender Clock.........................................................................38
Back Up and Manage the Extender Configuration...............................................39
Back Up the Configuration Settings................................................................39
Restore the Configuration Settings.................................................................40
Return the Extender to Its Factory Default Settings.............................................41
Use the Reset Button......................................................................................41
Log In and Reset the Extender to Factory Settings.........................................41
Update the Extender Firmware............................................................................42
Check for New Firmware and Update the Extender........................................42
Manually Upload Firmware to the Extender....................................................43
Restart the Extender Remotely............................................................................44
Turn the LEDs On or Off......................................................................................45
Chapter 5 FAQs and Troubleshooting
FAQs....................................................................................................................48
Find the Extender’s IP Address............................................................................49
Cannot Connect to the Extender..........................................................................49
Cannot Join a WiFi Network and Receive an Error Message..............................50
Cannot Access mywifiext.net...............................................................................50
Chapter 6 Supplemental Information
Factory Default Settings.......................................................................................53
Technical and Environmental Specifications........................................................54
4
Overview
The WiFi Range Extender boosts your existing network range and speed, delivering tri-band WiFi.
This chapter covers the following topics:
• Unpack Your Extender
• LEDs
• Back Panel
• When to Use Your Extender
• How the Extender Works
For more information about the topics covered in this manual, visit the support website at
Note
support.netgear.com.
1
5
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
Unpack Your Extender
Your package contains the following items.
Figure 1. Extender package contents
1. Nighthawk X6 AC2200 Tri-Band WiFi Range Extender (Model EX7700)
2. Power adapter (varies by region)
Overview
6
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
LEDs
The following table describes the LEDs.
Figure 2. Front panel
Overview
7
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
Table 1. LED descriptions
DescriptionLED
Router Link LED
Client Link LED
WPS LED
This LED indicates the WiFi connection between the extender and the router.
• Solid white. Best connection.
• Solid amber. Good connection.
• Solid red. Poor connection.
• Off. No connection.
• Solid white.The extender is connected to a WiFi-enabled computer or mobile
device.
• Off.The extender is not connected to a WiFi-enabled computer or mobile
device.
• Blinking white. A WPS connection is being established.
• Solid white.The extended network is enabled with WiFi security (either WPA
or WPA2).
• Off.The extended network is enabled without WiFi security.
Overview
8
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
Table 1. LED descriptions (Continued)
DescriptionLED
Ethernet LED
• Solid white. An Ethernet device is connected to an Ethernet port.
• Off. An Ethernet device is not connected to the extender.
Power LED
The Power LED is on the back of the extender.
• Solid green.The extender is powered on.
• Solid amber.The extender is booting.
• Blinking amber.The extender is resetting to its factory default
settings.
• Blinking green.The firmware is corrupted.
• Off.The extender is powered off.
Back Panel
The back panel of the extender provides ports, buttons, and a DC power connector.
Figure 3. Back panel
Overview
9
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
The back panel contains the following components:
• WPS button. Use this button to connect WPS-enabled devices to the extender.
• Ethernet ports. Use the two Gigabit Ethernet RJ-45 LAN ports to connect the extender to LAN devices.
• Power On/Off b utton and Po wer LED. Press the P ower On/Off b utton to provide power to the e xtender.
The Power LED lights green when the extender is ready.
• DC power connector. Connect the power adapter that came in the product package to the DC power
connector.
• Reset button. Pressing this b utton resets the extender. If the Reset button is pressed for at least sev en
seconds, the Power LED blinks amber, and the extender returns to its factory settings.
When to Use Your Extender
We recommend that you connect through the extender network only when your WiFi device is in a “dead
zone” where connection from the existing network is poor or nonexistent. Data traffic routed through the
extender is inherently slower than traffic routed directly from the network.
How the Extender Works
The extender works like a bridge between a WiFi router (or a WiFi access point) and a WiFi device outside
the range of the WiFi router.The extender performs two main jobs:
• The extender connects to a working WiFi network.
When the extender connects over WiFi to an existing network, it functions as a network client, similar
to how a WiFi device connects to a network.
• The extender acts as an access point for WiFi devices.
The extender broadcasts its own WiFi netw ork that WiFi devices can join. In its role as an access point,
the extender performs tasks that WiFi routers do, such as broadcasting its network name (SSID).
The extender must do each of these jobs so that both ends of the bridge are in place.
Overview
10
Get Started
This chapter covers the following topics:
• Install the WiFi Extender
• Use the Extender in Access Point Mode
• Connect a Device to the Extender Network
• Log In to the Extender After Installation
• Run Smart Setup Installation
2
11
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
Install the WiFi Extender
Place the extender, apply power, and connect the extender to your existing WiFi network.
Place the Extender and Apply Power
To place the extender and apply power:
1. Place your extender in the same room as your WiFi router.
Proximity to the WiFi router is required only during the initial setup process.
2. Connect the power adapter to your extender and plug the power adapter into an outlet.
3. Wait for the Power LED to light amber and then turn green.
If the Power LED does not light, press the Power On/Off button on the extender.
Connect to an Existing WiFi Network
To extend the range of your WiFi network, you must connect the extender to your existing WiFi network.
If your router’s WiFi security is set to WPA enterprise or WPA2 enterprise, your
Note
extender can’t connect to your router.You must change your router’s WiFi security
setting.
You can connect the extender in one of two ways:
• Connect with WPS. For more information, see Connect With WPS on page 12.
WPS does not support WEP network security or a hidden SSID network. If your router
Note
WiFi network uses WEP security or its SSID is hidden, follow the instructions in
Connect With the NETGEAR Installation Assistant on page 14.
• Connect with web browser setup. F or more inf ormation, see Connect With the NETGEAR Installation
Assistant on page 14.
Connect With WPS
Wi-Fi Protected Setup (WPS) lets you join a secure WiFi network without typing the network name and
password. For help with the WPS button on your WPS-enabled de vice , chec k the instructions or online help
that came with that device. Some older equipment cannot use WPS.
WPS does not support WEP network security or a hidden SSID network. If your
Note
existing WiFi network uses WEP security or its SSID is hidden, follow the instructions
in Connect With the NETGEAR Installation Assistant on page 14.
Get Started
12
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
To use WPS to connect the extender to your WiFi router:
1. Press the WPS button on the extender.
The WPS LED blinks.
2. Within two minutes, press the WPS button on your router or access point.
When the extender connects to your existing WiFi network, the WPS LED on the extender lights solid
white and the Router Link LED lights.
If the Router Link LED lights white, the connection between your router and extender is good. If the
Router Link LED lights amber or red, move the extender closer to the router and try again.
If it still does not light, see Connect With the NETGEAR Installation Assistant on page 14.
If your router supports the 5 GHz band, your extender attempts to connect to the
Note
router’s 5 GHz band the first time y ou press the WPS button. If your extender did not
connect to the router’s 5 GHz band the first time, repeat the WPS process.
3. Unplug the extender and move it to a new location that is about halfway between your router and the
area with a poor router WiFi signal.
The location that you choose must be within the range of your existing WiFi router network.
4. Use the Router Link LED to help you choose a spot where the extender-to-router connection is optimal.
5. If the Router Link LED doesn’t light amber or white, move the e xtender closer to the router and try again.
Keep moving the extender closer to the router until the Router Link LED lights amber or white.
6. Take your WiFi-enabled computer or mobile device to the location with poor WiFi router coverage.
7. Connect your WiFi-enabled computer or mobile device to the extended network.
Your extender uses the same WiFi netw ork settings as y our router for its 2.4 GHz and 5 GHz extended
networks.
For example , if your extender connects to the router’ s 5 GHz WiFi band, your extender uses y our router’ s
5 GHz WiFi settings for both its networks:
• Router 2.4 GHz WiFi network name. MyWiFiExample
• Router 5 GHz WiFi network name. MyWiFiExample-5G
• Extended 2.4 GHz WiFi network name. MyWiFiExample-5G
• Extended 5 GHz WiFi network name. MyWiFiExample-5G
If your extender connects to the router’s 2.4 GHz WiFi band, your extender uses your router’s 2.4 GHz
WiFi settings for both its networks:
Get Started
13
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
• Router 2.4 GHz WiFi network name. MyWiFiExample
• Router 5 GHz WiFi network name. MyWiFiExample-5G
• Extended 2.4 GHz WiFi network name. MyWiFiExample
• Extended 5 GHz WiFi network name. MyWiFiExample
Since your router and extended networks share the same WiFi network name, only
Note
one WiFi network name is broadcast.
Connect With the NETGEAR Installation Assistant
You can use the NETGEAR installation assistant to connect your extender to your existing WiFi router
network.To use the NETGEAR installation assistant, you must launch a web browser on your computer or
mobile device.
To use the NETGEAR installation assistant to connect the extender to your WiFi router:
1. Connect a computer or mobile device to the extender using a WiFi or Ethernet connection:
• WiFi. On your WiFi-enabled computer or mobile device, open the WiFi connection manager and
locate and connect to the extender network called NETGEAR_EXT.
When your WiFi-enabled computer or mobile device is connected to the extender, the Client LED
lights solid white.
• Ethernet. Use an Ethernet cable to connect the Ethernet port on the extender to an Ethernet port
on your computer.
2. Launch web browser.
3. Enter http://www.mywifiext.net.
The NETGEAR installation assistant displays.
4. Follow the prompts to connect your extender to your existing WiFi network.
5. Unplug the extender and mov e it to a new location about halfw ay betw een your router and the area with
a poor WiFi signal.
6. Use the Router Link LED to help you choose a spot where the extender-to-router connection is optimal.
7. If the Router Link LED doesn’t light amber or white, move the e xtender closer to the router and try again.
Keep moving the extender closer to the router until the Router Link LED lights amber or white.
8. Reconnect your computer or mobile device to the new extender WiFi network.
Get Started
14
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
Use the Extender in Access Point Mode
You can use the extender as a WiFi access point, which creates a new WiFi hotspot by using a wired Ethernet
connection.The following instructions assume that this is the first time you're setting up the extender.
Figure 4. Extender in access point mode
To use the extender in access point mode:
1. Place your extender in the same room as your router.
2. Connect the power adapter to your extender and plug the power adapter into an outlet.
3. Use an Ethernet cable to connect your router to an Ethernet port on the extender.
Do not connect your extender directly to your DSL or cable modem.The extender
Note
does not function as a router. If y our network includes a DHCP server, y ou can connect
the extender to a switch or hub that is connected to the DHCP server.
4. Wait for the Power LED to light amber and then turn green.
If the Power LED does not light, press the Power On/Off button on the side of the extender.
5. Connect a computer or mobile device to the extender using a WiFi or Ethernet connection:
• WiFi. On your WiFi-enabled computer or mobile device, open the WiFi connection manager and
connect to the extender network called NETGEAR_EXT.
When your WiFi-enabled computer or mobile device is connected to the extender, the Client LED
lights solid white.
• Ethernet. Connect the Ethernet cable to the Ethernet port on your computer and extender.
If you want to use an Ethernet connection, you must do this before you connect
Note
your extender to your modem router or router.
6. Launch a web browser and visit www.mywifiext.net.
When you join the network, the Client Link LED lights to show that you are connected.
Get Started
15
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
The NETGEAR installation assistant displays.
7. Return to the NETGEAR installation assistant and follow the prompts to finish setting up your e xtender
as an access point.
Connect a Device to the Extender Network
After you complete the setup process, you can connect all your devices to the new extender network using
a WiFi, wired, or WPS connection.
Connect a Device to the Extender Network Using WiFi
If you enabled the One WiFi Name f eature , your e xtender uses the same WiFi network name and password
as your router.
The following is an e xample of what y our WiFi network names might look like if One WiFi Name is enabled:
• Router 2.4 GHz WiFi network name. MyWiFiExample
• Router 5 GHz WiFi network name. MyWiFiExample-5G
• Extended 2.4 GHz WiFi network name. MyWiFiExample
• Extended 5 GHz WiFi network name. MyWiFiExample-5G
If you set up your extender using WPS, your extender uses the same WiFi network settings as your router
for its 2.4 GHz and 5 GHz extended networks.
For example , if your extender connects to the router’s 2.4 GHz WiFi band, your extender uses your router’s
2.4 GHz WiFi settings for both its networks:
• Router 2.4 GHz WiFi network name. MyWiFiExample
• Router 5 GHz WiFi network name. MyWiFiExample-5G
• Extended 2.4 GHz WiFi network name. MyWiFiExample
• Extended 5 GHz WiFi network name. MyWiFiExample
If your extender connects to the router’s 5 GHz WiFi band, your extender uses your router’s 5 GHz WiFi
settings for both its networks:
• Router 2.4 GHz WiFi network name. MyWiFiExample
• Router 5 GHz WiFi network name. MyWiFiExample-5G
• Extended 2.4 GHz WiFi network name. MyWiFiExample-5G
• Extended 5 GHz WiFi network name. MyWiFiExample-5G
Since your router and extended networks share the same WiFi network name, only one WiFi network name
is broadcast.
Get Started
16
Nighthawk X6 AC2200 Tri-Band WiFi Range Extender
To connect to the WiFi network:
1. On your WiFi-enabled computer or mobile device, open the WiFi connection manager that manages
your WiFi connections.
The WiFi connection manager scans for WiFi networks in your area.
2. Find and select your WiFi network name (SSID) and enter your WiFi password.
This is the SSID and password that you set up during the installation process.
Connect a Device to the Extender Network Using WPS
For help with the WPS button on y our WPS-enab led device, check the instructions or online help that came
with that device. Some older equipment cannot use WPS.
To connect to the extender using a WPS connection:
1. Press the WPS button on the extender.
The WPS LED blinks white.
2. Within two minutes, press the WPS button on your WPS-enabled device.
If your WPS enabled device successfully connects to extender, the WiFi connection manager on your
device will show connection status.
Connect an Ethernet-Enabled Device to the Extender
After the extender is connected to your e xisting WiFi netw ork, you can connect a wired device to the e xtender
using an Ethernet cable.
Figure 5. Ethernet LAN port
Log In to the Extender After Installation
After installation, you can log in to the extender to view or change the extender’s settings.
To log in to the extender:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
Get Started
17
Loading...