NEC 5800-230Eh User Manual

Page 1
N8100-1235F/1236F/1321F/1322F
1287F/1288F/1352F
N8100-1237F/1238F/1323F/1324F
1290F/1291F/1293F
NEC Express5800/120Eh
User's Guide
3rd Edition
5-2007
ONL-4152dN-120Eh-100-99-0704
Page 2
PROPRIETARY NOTICE AND LIABILITY DISCLAIMER
The NEC product(s) discussed in this document are warranted in accordance with the terms of the Warranty Statement accompanying each product. However, actual performance of each such product is dependent upon factors such as system configuration, customer data, and operator control. Since implementation by customers of each product may vary, the suitability of specific product configurations and applications must be determined by the customer and is not warranted by NEC.
To allow for design and specification improvements, the information in this document is subject to change at any time, without notice. Reproduction of this document or portions thereof without prior written approval of NEC is prohibited.
First Printing, July 2006
Revised, May 2007
Copyright 2006, 2007
NEC Corporation
7-1 Shiba 5-Chome, Minato-Ku
Tokyo 108-8001, Japan
All Rights Reserved
Printed in Japan
Page 3
Keep this manual at hand for quick reference at anytime necessary.

SAFETY INDICATIONS

Follow the instructions in this manual for your safety to use the NEC Express server.
Your server contains components with possible danger, hazards that may cause by ignoring warnings, and preventive actions against such hazards.
Server components with possible danger are indicated with a warning label placed on or around them as well as described in this manual.
In this manual or warning labels, "WARNING" or "CAUTION" is used to indicate a degree of danger. These terms are defined as follows:
WARNING
CAUTION
Precautions and notices against hazards are presented with one of the following three symbols. The individual symbols are defined as follows:
This symbol indicates the presence of a hazard if the instruction is ignored. An image in the symbol illustrates the hazard type. (Attention)
This symbol indicates prohibited actions. An image in the symbol illustrates a particular prohibited action. (Prohibited Action)
This symbol indicates mandatory actions. An image in the symbol illustrates a mandatory action to avoid a particular hazard. (Mandatory Action)
(Example)
Indicates the presence of a hazard that may result in death or serious personal injury if the instruction is ignored. Indicates the presence of a hazard that may cause minor personal injury, including burns, or property damage if the instruction is ignored.
Symbol to draw attention
Term indicating a degree of danger
CAUTION
High temperature. Immediately after the server is powered off, its internal components such as hard disk drives are very hot. Leave the server until its internal components fully cool down before installing/removing any component.
Symbol indicating a prohibited action (may not always be indicated)
Description of a danger
Page 4

SYMBOLS USED IN THIS MANUAL AND WARNING LABELS

Attentions
Indicates that improper use may cause an electric shock.
Indicates that improper use may cause personal injury.
Indicates that improper use may cause fingers to be caught.
Indicates that improper use may cause fumes or fire.
Indicates a general notice or warning that cannot be specifically identified.
Indicates that improper use may cause loss of eyesight due to laser beam.
Prohibited Actions
Indicates a general prohibited action that cannot be specifically identified.
Do not disassemble, repair, or modify the server. Otherwise, an electric shock or fire may be caused.
Mandatory Action
Unplug the power cord of the server. Otherwise, an electric shock or fire may be caused.
Indicates a mandatory action that cannot be specifically identified. Make sure to follow the instruction.
Page 5
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help
Momentary voltage drop prevention:
This product may be affected by a momentary voltage drop caused by lightning. To prevent a momentary voltage drop, an AC uninterruptible power supply (UPS) unit should be used.
Page 6
Trademarks
NEC ESMPRO, NEC EXPRESSBUILDER, and NEC EXPRESSSCOPE are trademarks of NEC Corporation. Microsoft, Windows, Windows Server, Windows NT, and MS-DOS are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. Intel and Pentium are registered trademarks of Intel Corporation. LSI Logic, LSI Logic Logo Design, MegaRAID, MegaRAID Storage Manager, and Power Console Plus are registered trademarks or trademarks of LSI Corporation. Datalight is a registered trademark of Datalight, Inc. ROM-DOS is a trademark of Datalight, Inc. Novell and NetWare are registered trademarks of Novell, Inc. of the United States. AT is a registered trademark of International Business Machines Corporation in the United States and other countries. Adobe, Adobe logo, and Acrobat are trademarks of Adobe Systems Incorporated. DLT and DLTtape are trademarks of Quantum Corporation of the United States. All other product, brand, or trade names used in this publication are the trademarks or registered trademarks of their respective trademark owners.
Windows Server 2003 x64 Editions stands for Microsoft® Windows® Server 2003 R2, Standard x64 Edition Operating system and Microsoft® Windows® Server 2003 R2, Enterprise x64 Edition operating system, or Microsoft® Windows® Server 2003, Standard x64 Edition operating system and Microsoft® Windows® Server 2003, Enterprise x64 Edition operating system. Windows Server 2003 stands for Microsoft® Windows® Server 2003 R2, Standard Edition operating system and Microsoft® Windows® Server 2003 R2, Enterprise Edition operating system, or Microsoft® Windows® Server 2003, Standard Edition operating system and Microsoft® Windows® Server 2003, Enterprise Edition operating system. Windows Vista stands for Microsoft® Windows Vista Business operating system. Windows XP x64 Edition stands for Microsoft® Windows® XP Professional x64 Edition operating system. Windows XP stands for Microsoft® Windows® XP Home Edition operating system and Microsoft
Windows® XP Professional operating system. Windows 2000 stands for Microsoft® Windows® 2000 Server operating system and Microsoft® Windows® 2000 Advanced Server operating system, and Microsoft Windows® 2000 Professional operating system. Windows NT stands for Microsoft® Windows NT® Server network operating system version 3.51/4.0 and Microsoft® Windows NT® Workstation operating system version 3.51/4.0. Windows Me stands for Microsoft® Windows® Millennium Edition operating system. Windows 98 stands for Microsoft® Windows®98 operating system. Windows 95 stands for Microsoft Windows®95 operating system.
®
®
®
Notes:
(1) No part of this manual may be reproduced in any form without the prior written permission of
NEC Corporation.
(2) The contents of this manual may be revised without prior notice.
(3) The contents of this manual shall not be copied or altered without the prior written permission
of NEC Corporation.
(4) All efforts have been made to ensure the accuracy of all information in this manual. If you
notice any part unclear, incorrect, or omitted in this manual, contact the service representative where you purchased this product.
(5) NEC assumes no liability arising from the use of this product, nor any liability for incidental or
consequential damages arising from the use of this manual regardless of Item (4).
Page 7

PREFACE

Congratulations on the purchase of your NEC Express server.
Purchase of this server is your assurance of receiving state-of-the-art, high quality hardware to meet your needs, both now and in the future.
Read this User's Guide thoroughly to fully understand handling of the NEC Express server and appreciate its functions to the maximum extent.
i
Page 8
ii

ABOUT THIS USER'S GUIDE

This manual is a guide for proper setup and use of your server. This manual also covers useful procedures for dealing with difficulties and problems that may arise during setup or operation of your server. Keep this manual for future use. The following describes how to proceed with this manual.
How to Use This Manual
To aid you in finding information quickly, this manual contains the following information:
Chapter 1 Notes on Using Your Server
includes information that needs attention to use the server. Make sure to read this chapter before setting up and using the server. It also includes requirements and advisory information for transfer and disposal of the server.
Chapter 2 General Description
includes information necessary to use the server, such as names and functions of its components, handling of the floppy disk and DVD-ROM drives.
Chapter 3 Setting Up Your Server
tells you how to select a site, unpack the system, make cable connections, and power on your system.
Chapter 4 Configuring Your Server
tells you how to configure the system and provides instructions for running the BIOS SETUP Utility and the RAID configuration utility, which is used to configure RAID drives in your system. This chapter also provides information on mother board jumper settings.
Chapter 5 Installing the Operating System with Express Setup
describes how to install the operating system.
Chapter 6 Installing and Using Utilities
describes how to install the utilities for the server. It also includes a description on using the attached "NEC EXPRESSBUILDER" CD-ROM.
Chapter 7 Maintenance
provides you with all the information necessary to maintain successful operation of the server. This chapter also includes a description on relocating and storing the server.
Chapter 8 Troubleshooting
contains helpful information for solving problems that might occur with your system.
Chapter 9 Upgrading Your Server
provides you with instructions for upgrading your system with an additional processor, optional memory, optional add-in cards, hard disk drives, peripheral devices, and power supply.
Chapter 10 Internal Cabling Diagram
includes cabling information for the SAS/SATA2 controller, 5.25-inch device, and the power supply.
Appendix A Specification
provides specifications for your server.
Page 9
Appendix B Other Precautions
provides supplementary notes on using the server.
Appendix C IRQ and I/O Port Address
provides a list of factory-set IRQs and I/O port addresses assigned.
Appendix D Installing Windows Server 2003 x64 Editions
describes how to install Microsoft Windows Server 2003 x64 Editions without using Express Setup. Using the Express Setup tool is recommended for installing Windows Server 2003 x64 Editions. See Chapter 5 for details.
Appendix E Installing Windows Server 2003
describes how to install Microsoft Windows Server 2003 without using Express Setup. Using the Express Setup tool is recommended for installing Windows Server 2003. See Chapter 5 for details.
Appendix F Product Configuration Record Table
provides a table to be filled with your server configuration.
Text Conventions
The following conventions are used throughout this manual. For safety symbols, see "SAFETY INDICATIONS" provided earlier.
iii
IMPORTANT:
NOTE:
Items that are mandatory or require attention when using the server
Helpful and convenient piece of information

IN THE PACKAGE

The carton contains various accessories, as well as the server itself. See the packing list to make sure that you have everything and that individual components are not damaged. If you find any component missing or damaged, contact your service representative.
Store the provided accessories in a designated place for your convenience. You will need
them to install an optional device or troubleshoot your server, as well as to set it up.
Make a backup copy of each provided floppy disk, if any. Store the original disk as the
master disk in a designated place, and use its copy.
Improper use of any provided CD-ROM may alter your system environment. If you find
anything unclear, immediately ask your service representative for help.
Page 10
iv

CONTENTS

Preface ..............................................................................................................................................i
About This User's Guide..................................................................................................................ii
In the Package.................................................................................................................................iii
Chapter 1 Notes on Using Your Server........................................................................ 1-1
Warning Labels.............................................................................................................................1-2
Safety Notes..................................................................................................................................1-3
General .....................................................................................................................................1-3
Power Supply and Power Cord Use .........................................................................................1-4
Installation, Relocation, Storage, and Connection....................................................................1-5
Cleaning and Working with Internal Devices...........................................................................1-6
During Operation .....................................................................................................................1-7
For Proper Operation....................................................................................................................1-8
Transfer to Third Party .................................................................................................................1-9
Disposal and Consumables.........................................................................................................1-10
User Support...............................................................................................................................1-11
Chapter 2 General Description ..................................................................................... 2-1
Overview ......................................................................................................................................2-2
System Chassis .............................................................................................................................2-3
Front View................................................................................................................................2-3
Rear View.................................................................................................................................2-6
Internal View............................................................................................................................2-8
Mother Board..............................................................................................................................2-10
Standard Features .......................................................................................................................2-12
Power Supply .........................................................................................................................2-13
Peripheral Bays ......................................................................................................................2-13
Remote Power-On Feature (Wake On LAN)..........................................................................2-13
AC LINK Feature...................................................................................................................2-13
Security ..................................................................................................................................2-13
NEC EXPRESSBUILDER ....................................................................................................2-14
NEC ESMPRO.......................................................................................................................2-14
Off-line Maintenance Utility..................................................................................................2-15
System Diagnostic Utility ......................................................................................................2-15
Remote Management..............................................................................................................2-15
Using Your Server.......................................................................................................................2-16
POWER Switch......................................................................................................................2-16
Power Off...............................................................................................................................2-20
SLEEP Switch........................................................................................................................2-20
DVD-ROM Drive...................................................................................................................2-21
Page 11
Chapter 3 Setting Up Your Server ................................................................................ 3-1
Setup Flow....................................................................................................................................3-2
Unpacking the System ..................................................................................................................3-3
Installing Optional Devices ..........................................................................................................3-3
Selecting Server Site.....................................................................................................................3-4
Connecting Peripheral Devices.....................................................................................................3-6
Connecting Power Cord................................................................................................................3-8
Turning On the Server ................................................................................................................3-10
Installing Operating System .......................................................................................................3-12
Installing Utilities .......................................................................................................................3-12
Making Backup Copies of System Information..........................................................................3-12
Chapter 4 Configuring Your Server.............................................................................. 4-1
System BIOS (BIOS Setup Utility) ..............................................................................................4-2
Starting SETUP Utility.............................................................................................................4-3
Description on On-Screen Items and Key Usage.....................................................................4-4
Configuration Examples...........................................................................................................4-5
Menu and Parameter Descriptions ...........................................................................................4-9
Setup Utility................................................................................................................................4-31
Running Setup Utility.............................................................................................................4-31
Menu Tree ..............................................................................................................................4-33
Operating Procedures for Setup Utility ..................................................................................4-34
Add-in Card's BIOS....................................................................................................................4-44
Configuring Mother Board Jumpers...........................................................................................4-45
v
Chapter 5 Installing the Operating System with Express Setup............................... 5-1
About Express Setup ....................................................................................................................5-2
Microsoft Windows Server 2003..................................................................................................5-3
Installation Notice ....................................................................................................................5-3
The Flow of Setup....................................................................................................................5-8
Installing and Setting Device Drivers.....................................................................................5-14
Setting for Solving Problems .................................................................................................5-22
Installing Maintenance Utilities .............................................................................................5-26
Updating the System – Installing Service Pack –...................................................................5-27
Making Backup Copies of System Information .....................................................................5-27
Installing with the OEM-FD for Mass Storage Device ..........................................................5-28
Page 12
vi
Chapter 6 Installing and Using Utilities ....................................................................... 6-1
NEC EXPRESSBUILDER...........................................................................................................6-2
NEC EXPRESSBUILDER for DOS-Based with Local Console.............................................6-4
NEC EXPRESSBUILDER for DOS-based with Remote Console..........................................6-9
Starting ...................................................................................................................................6-10
NEC EXPRESSBUILDER for Windows-Based (Master Control Menu)..............................6-13
Configuration Diskette Creator...................................................................................................6-14
NEC ESMPRO ...........................................................................................................................6-18
Functions and Features...........................................................................................................6-18
Web-based Promise Array Manager ...........................................................................................6-19
MegaRAID Storage Manager (Server).......................................................................................6-19
Setup with Express Setup.......................................................................................................6-19
Manual Setup .........................................................................................................................6-19
MegaRAID Storage Manager (Management PC) .......................................................................6-19
Power Console Plus....................................................................................................................6-20
Major Functions .....................................................................................................................6-20
Components............................................................................................................................6-20
Server Setup ...........................................................................................................................6-22
Management PC Setup...........................................................................................................6-23
NEC DianaScope........................................................................................................................6-24
Chapter 7 Maintenance.................................................................................................. 7-1
Making Backup Copies ................................................................................................................7-1
Cleaning........................................................................................................................................7-2
Cleaning the Server ..................................................................................................................7-3
Cleaning the Interior.................................................................................................................7-4
Cleaning the Keyboard/Mouse.................................................................................................7-5
Cleaning Disc ...........................................................................................................................7-6
System Diagnostics.......................................................................................................................7-7
Test Items.................................................................................................................................7-7
Startup and Exit of System Diagnostics ...................................................................................7-8
Relocating/Storing The Server....................................................................................................7-11
Page 13
vii
Chapter 8 Troubleshooting........................................................................................... 8-1
System Viewers ............................................................................................................................8-2
Lamps ...........................................................................................................................................8-3
POWER/SLEEP Lamp.............................................................................................................8-4
Access Lamps...........................................................................................................................8-4
DISK Access Lamp ..................................................................................................................8-4
LINK/ACT Lamp.....................................................................................................................8-4
1000/100/10 Lamp ...................................................................................................................8-5
100/10 Lamp ............................................................................................................................8-5
Hard Disk Drive Lamp.............................................................................................................8-5
Error Messages .............................................................................................................................8-7
Error Messages after Power-on................................................................................................8-7
POST Error Messages ..............................................................................................................8-8
Beep Codes.............................................................................................................................8-11
Solving Problems........................................................................................................................8-12
Problems with NEC Express Server.......................................................................................8-12
Problems with Windows Server 2003 x64 Editions ...............................................................8-16
Problems with Windows Server 2003 R2...............................................................................8-17
Problems with Windows Server 2003 ....................................................................................8-18
Problems with NEC EXPRESSBUILDER ............................................................................8-21
Problems with Express Setup.................................................................................................8-22
Problems with Disk Array Configuration...............................................................................8-25
Problems with Master Control Menu .....................................................................................8-26
Collecting Event Log .............................................................................................................8-26
Collect Configuration Information.........................................................................................8-27
Collecting Dr. Watson Diagnostic Information ......................................................................8-27
Memory Dump.......................................................................................................................8-27
Off-line Maintenance Utility ......................................................................................................8-28
Starting the Off-line Maintenance Utility...............................................................................8-28
Features of Off-line Maintenance Utility ...............................................................................8-29
Resetting the Server....................................................................................................................8-30
Forced Shutdown........................................................................................................................8-30
Chapter 9 Upgrading Your Server ................................................................................ 9-1
Safety Notes..................................................................................................................................9-2
Static Precautions .........................................................................................................................9-3
Preparing for Installation and Removal........................................................................................9-4
Installation or Removal Procedure ...............................................................................................9-5
Left Side Cover ........................................................................................................................9-5
Front Mask ...............................................................................................................................9-8
3.5-inch Hard Disk Drive (SAS Model).................................................................................9-10
3.5-inch Hard Disk Drive (SATA Model)...............................................................................9-17
PCI Board...............................................................................................................................9-23
DIMM ....................................................................................................................................9-33
Processor (CPU).....................................................................................................................9-42
File Device .............................................................................................................................9-48
Additional HDD Cage............................................................................................................9-54
Page 14
viii
Chapter 10 Internal Cabling Diagrams....................................................................... 10-1
Interface Cables ..........................................................................................................................10-2
Addition of Hard Disk Drive..................................................................................................10-2
Connection of Disk Array Controller N8103-91 (SAS) .........................................................10-4
Connection of Disk Array Controller N8103-101 (SATA2)...................................................10-6
Connection of 5.25-inch Device.............................................................................................10-9
Power Cables ............................................................................................................................10-11
Appendix A Specifications............................................................................................A-1
Appendix B Other Precautions.....................................................................................B-1
Transfer Rate of the On-board LAN Controller ...................................................................... B-1
Server Management Software ................................................................................................. B-1
Floppy Disk............................................................................................................................. B-1
DVD/CD-ROM....................................................................................................................... B-4
Tape Media.............................................................................................................................. B-4
Keyboard................................................................................................................................. B-5
Mouse...................................................................................................................................... B-6
Appendix C IRQ and I/O Port Address.........................................................................C-1
Appendix D Installing Windows Server 2003 x64 Editions........................................D-1
Before Installing Windows Server 2003 x64 Editions.................................................................D-1
Optional Board Supported by NEC EXPRESSBUILDER......................................................D-1
Installing Service Pack ............................................................................................................D-2
Updating System .....................................................................................................................D-2
Re-installing to the Hard Disk which has been upgraded to Dynamic Disk ...........................D-2
Manual Installation when N8103-80F Keeps Connection.......................................................D-2
Mounting MO Device .............................................................................................................D-2
About Removable Media ........................................................................................................D-2
Creating Partition Size ............................................................................................................D-3
Installing Windows Server 2003 x64 Editions.............................................................................D-4
Creating "Windows Server 2003 x64 Edition OEM-DISK for NEC EXPRESSBUILDER".. D-4
Windows Server 2003 x64 Editions Clean Installation ...........................................................D-6
Reinstallation to Multiple Logical Drives ...............................................................................D-8
Updating the System .............................................................................................................D-10
Page 15
ix
Driver Installation and Advanced Settings ................................................................................D-11
PROSet..................................................................................................................................D-11
Adapter Fault Tolerance (AFT)/Adaptive Load Balancing (ALB)........................................D-12
Network Driver .....................................................................................................................D-13
Re-install the Network Driver ............................................................................................... D-14
Re-install the Optional Network Board Driver......................................................................D-15
Installation of the Optional Network Board Driver...............................................................D-15
Graphics Accelerator Driver.................................................................................................. D-16
Optional Network Board Driver............................................................................................ D-18
Installing SCSI Controller Driver (N8103-75)......................................................................D-19
Installing SCSI Controller Driver (N8103-95)......................................................................D-19
Installing Disk Array Controller Driver (N8103-80F) ..........................................................D-19
About Windows Activation ...................................................................................................D-20
Setting for Collecting Memory Dump (Debug Information).....................................................D-22
Appendix E Installing Windows Server 2003 .............................................................. E-1
Before Installing Windows Server 2003 ...................................................................................... E-1
Optional Board Supported by NEC EXPRESSBUILDER...................................................... E-1
Installing Service Pack ............................................................................................................ E-2
Updating System ..................................................................................................................... E-2
Re-installing to the Hard Disk which has been upgraded to Dynamic Disk ........................... E-2
Manual Installation when N8103-80F Keeps Connection....................................................... E-2
Mounting MO Device .............................................................................................................E-2
About Removable Media ........................................................................................................ E-2
Application of Service Pack.................................................................................................... E-2
Creating Partition Size ............................................................................................................ E-3
Installing Windows Server 2003..................................................................................................E-4
Creating "Windows Server 2003 OEM-DISK for NEC EXPRESSBUILDER" ..................... E-4
Windows Server 2003 Clean Installation ................................................................................ E-6
Reinstallation to Multiple Logical Drives ............................................................................... E-9
Re-installing the Operation System if Multiple Logical Drives Exist................................... E-11
Updating the System .............................................................................................................E-12
Driver Installation and Advanced Settings ................................................................................ E-13
PROSet.................................................................................................................................. E-13
Network Driver ..................................................................................................................... E-14
Re-install the Network Driver ............................................................................................... E-15
Graphics Accelerator Driver.................................................................................................. E-16
Installing SCSI Controller Driver (N8103-75/95)................................................................. E-18
Installing Disk Array Controller Driver (N8103-80F) .......................................................... E-18
Notes of N8103-75................................................................................................................ E-19
About Windows Activation ................................................................................................... E-20
Available Switch Options for Windows Server 2003 Boot.ini File....................................... E-22
Setting for Collecting Memory Dump (Debug Information)..................................................... E-23
Appendix F Product Configuration Record Table ...................................................... F-1
Hardware................................................................................................................................. F-1
Software .................................................................................................................................. F-3
Page 16
x
(This page is intentionally left blank.)
Page 17
Chapter 1

Notes on Using Your Server

This chapter includes information necessary for proper and safe operation of your server.
Page 18
1-2 Notes on Using Your Server

WARNING LABELS

The warning label is attached to components with possible danger or their vicinity in your server to inform the user that a hazardous situation may arise when operating the server. (Do not intentionally remove or damage any of the labels.)
If you find any labels totally/partially removed or illegible due to damage, contact your service representative.
Page 19
Notes on Using Your Server 1-3

SAFETY NOTES

This section provides notes on using your server safely. Read this section carefully to ensure proper and safe use of the server. For symbols, see "SAFETY INDICATIONS" provided earlier.

General

WARNING
Do not use the server for services where critical high availability may directly affect human lives.
Your server is not intended to be used with or control facilities or devices concerning human lives, including medical devices, nuclear facilities and devices, aeronautics and space devices, transportation facilities and devices; and facilities and devices requiring high reliability. NEC assumes no liability for any accident resulting in personal injury, death, or property damage if the server has been used in the above conditions.
Do not use the server if any smoke, odor, or noise is present.
If smoke, odor, or noise is present, immediately turn off the server and disconnect the power plug from the outlet, then contact your service representative. Using the server in such conditions may cause a fire.
Keep needles or metal objects away from the server.
Do not insert needles or metal objects into ventilation holes in the server or openings in the floppy disk or DVD-ROM drive. Doing so may cause an electric shock.
CAUTION
Do not access inside your server for a service or replacement of the internal components.
The service representative can only install or remove the internal components and optional devices. To avoid personal injury or electrical shock, contact your service representative when your need to install/remove the internal components.
Keep water or foreign matter away from the server.
Do not let any form of liquid (water etc.) or foreign matter (e.g., pins or paper clips) enter the server. Failure to follow this warning may cause an electric shock, a fire, or a failure of the server. When such things accidentally enter the server, immediately turn off the power and disconnect the power plug from the outlet. Do not disassemble the server. Contact your service representative.
Page 20
1-4 Notes on Using Your Server

Power Supply and Power Cord Use

Do not hold the power plug with a wet hand.
Do not disconnect/connect the plug while your hands are wet. Failure to follow this warning may cause an electric shock.
Plug in to a proper power source.
Use a proper wall outlet. Use of an improper power source may cause a fire or a power leak. Do not install the server where you need an extension cord. Use of a cord that does not meet the power specifications of your server may heat up the cord and cause a fire.
Do not connect the power cord to an outlet that has an illegal number of connections.
The electric current exceeding the rated flow overheats the outlet, which may cause a fire.
Do not pull the cable when disconnecting it.
When disconnecting the cable from the device, hold the cable connector and pull it straight out. Pulling the cable out by the cable portion or giving mechanical stress to the connector could damage the cables and connectors to result in an electrical shock hazard or a fire.
Insert the power plug into the outlet as far as it goes.
Heat generation resulting from a halfway inserted power plug (imperfect contact) may cause a fire. Heat will also be generated if condensation is formed on dusty blades of the halfway inserted plug, increasing the possibility of fire.
Use the authorized power cord only.
Use only the power cord that comes with your server. Use of an unauthorized power cord may cause a fire when the electric current exceeds the rated flow. Also, observe the following to prevent an electric shock or fire caused by a damaged cord.
Do not stretch the cord harness.
Do not pinch the power cord.
Do not bend the power cord.
Keep chemicals away from the power cord.
Do not twist the power cord.
Do not place any object on the power cord.
Do not bundle power cords.
Do not alter, modify, or repair the power cord.
Do not secure the power cord with staples or equivalents.
Do not use any damaged power cord. (Replace a damaged power cord
with a new one of the same specifications. Ask your service representative for replacement.)
WARNING
CAUTION
Page 21
Notes on Using Your Server 1-5

Installation, Relocation, Storage, and Connection

WARNING
Disconnect the power cord(s) before installing or removing the server.
Make sure to power off the server and disconnect the power cord(s) from a power outlet before installing/removing the server. All voltage is removed only when the power cords are unplugged.
CAUTION
Never attempt to lift the server only by yourself.
Your server weighs max 20 kg (depending on its hardware configuration). Carrying the server only by yourself may strain your back. Hold the server firmly by its bottom with at least two or more people. Do not hold the front mask to lift the server. The front mask may be disengaged from the server, causing personal injury.
Do not install the server in any place other than specified.
Do not install the server in the following places or any place other than specified in this manual. Failure to follow this instruction may cause a fire.
a dusty place
a humid place such as near a boiler
a place exposed to direct sunlight
an unstable place
Do not connect any interface cable with the power cord of the server plugged to a power source.
Make sure to power off the server and unplug the power cord from a power outlet before installing/removing any optional internal device or connecting/disconnecting any interface cable to/from the server. If the server is off-powered but its power cord is plugged to a power source, touching an internal device, cable, or connector may cause an electric shock or a fire resulted from a short circuit.
Do not use any unauthorized interface cable.
Use only interface cables provided by NEC and locate a proper device and connector before connecting a cable. Using an authorized cable or connecting a cable to an improper destination may cause a short circuit, resulting in a fire. Also, observe the following notes on using and connecting an interface cable.
Do not use any damaged cable connector.
Do not step on the cable.
Do not place any object on the cable.
Do not use the server with loose cable connections.
Page 22
1-6 Notes on Using Your Server

Cleaning and Working with Internal Devices

WARNING
Do not disassemble, repair, or alter the server.
Never attempt to disassemble, repair, or alter the server on any occasion other than described in this manual. Failure to follow this instruction may cause an electric shock or fire as well as malfunctions of the server.
Do not look into the DVD-ROM drive.
A laser beam used in the DVD-ROM drive is harmful to the eyes. Do not look into or insert a mirror into the drive while the drive is powered. If a laser beam is caught in your eyes, you may lose your eyesight (the laser beam is invisible).
Do not remove the lithium battery.
Your server contains the lithium battery. Do not remove the battery. Placing the lithium close to a fire or in the water may cause an explosion.
When the server does not operate appropriately due to the dead lithium battery, contact your service representative. Do not disassemble the server to replace or recharge the battery by yourself.
Disconnect the power plug before accessing inside the server, or connecting the peripherals.
Make sure to power off the server and disconnect the power plug from a power outlet before cleaning or installing/removing internal optional devices. Touching any internal device of the server with its power cord connected to a power source may cause an electric shock even of the server is off-powered.
Disconnect the power plug from the outlet occasionally and clean the plug with a dry cloth. Heat will be generated if condensation is formed on a dusty plug, which may cause a fire.
CAUTION
Avoid installation in extreme temperature conditions.
Immediately after the server is powered off, its internal components such as hard disk drives are very hot. Leave the server until its internal components fully cool down before installing/removing any component.
Make sure to complete board installation.
Always install a board firmly. An incompletely installed board may cause a contact failure, resulting in smoking or fire.
Protect the unused connectors with the protective cap.
The unused power supply cable connectors are covered with the protective cap to prevent short circuits and electrical hazards, when removing the power supply cable connector from the install devices, attach the protective cap to the connector. Failure to follow this warning may cause a fire or an electric shock.
Page 23

During Operation

Stay away from the fan.
Keep your hand or hair away from the cooling fan on the rear of the server. Failure to follow this warning may get your hand or hair caught in the fan, resulting in injury.
Avoid contact with the server during thunderstorms.
Disconnect the power plug from the outlet when a thunderstorm is approaching. If it starts thundering before you disconnect the power plug, do not touch any part of the server including the cables. Failure to follow this warning may cause a fire or an electric shock.
Keep animals away from the server.
Failure to follow this warning may cause a fire or an electric shock.
Do not leave the CD tray open.
Notes on Using Your Server 1-7
CAUTION
If dust gets on the lens of DVD-ROM drive, the drive may have problems reading your disks. Also, the CD tray may be broken by contacting any objects.
Take off the headset before connection.
To protect your ears, take off the headset before connecting it to the headset jack. Make sure that the volume is not extremely turned up before connection.
Do not place any object on top of the server.
The server may fall and cause property damage to the surroundings.
Do not use a cellular phone or pager around the server.
Turn off the cellular phone or pager. Radio interference may cause malfunctions of the server.
Page 24
1-8 Notes on Using Your Server

FOR PROPER OPERATION

Observe the following notes for successful operation of the server. Use of the server ignoring the notes will cause malfunctions or failures of the server.
Install the server in a place that meets requirements for successful operation. For details,
see Chapter 3, "Setting Up Your Server."
If the power cord supplied with your system is not compatible with the AC wall outlet in
your region, contact your service representative to obtain a suitable power cord.
Make sure to power off the server before connecting or disconnecting cables between the
server and peripheral devices.
Verify that the access lamp on the server is unlit before turning off the server or ejecting
the floppy disk.
When plugging the power cord to the system, you may experience 10 seconds delay from
the time you press the POWER/SLEEP switch on the front panel. This is normal system operation.
When you have just turned off the server, wait at least 10 seconds before turning it back
on. If the server is connected to the UPS, set at least 10 seconds delay in the power-on schedule.
For the disk which does not conform to the CD standard, the playback of such a disk with
the CD drive is not guaranteed.
Turn off the power and unplug the power cord from the outlet before relocating the server.
Clean the server on a regular basis. (See Chapter 7 for cleaning.) Regular cleaning
proactively prevents various failures of the server.
Lightning may cause a momentary voltage drop. To prevent this problem, it is
recommended to use of an uninterruptible power supply unit.
Make sure to use optional devices supported by the server. Some non-supported devices
may be physically installed/connected but cause failures of the server as well as malfunctions of the server.
NEC recommends you use NEC's genuine products. Some third-party products claim that
they support the server. However, repair of the server due to a failure or damage resulted from use of such third-party products will be charged.
Page 25
Notes on Using Your Server 1-9

TRANSFER TO THIRD PARTY

The following must be observed when you transfer (or sell) the server or software provided with the server to a third party:
Make sure to provide this manual along with the server to a third party.
IMPORTANT: About data on the hard disk drive
Be sure to take appropriate measures not to leak important data (e.g., customers' information or companies' management information) on the removed hard disk drive to any third parties.
Data seems to be erased when you empty "Recycle Bin" of Windows or execute the "format" command of the operating system. However, the actual data remains written on the hard disk drive. Data not erased completely may be restored by special software and used for unexpected purposes.
It is strongly recommended that the software or service (both available at stores) for data erasure should be used in order to avoid the trouble explained above. For details on data erasure, ask your sales representative.
Provided software
To transfer or sell any software application that comes with the server to a third party, the following requirements must be satisfied:
All provided software applications must be transferred and no backup copies must be
retained.
Transfer requirements listed in "Software License Agreement" that comes with each
software application must be satisfied.
Software applications that are not approved for transfer must be uninstalled before
transferring the server.
Page 26
1-10 Notes on Using Your Server

DISPOSAL AND CONSUMABLES

Dispose of the server, all the internal devices and DVD/CD-ROMs according to all
national laws and regulations.
IMPORTANT:
For disposal (or replacement) of the battery on the mother board of
the server, consult with your service representative.
It is the user's responsibility to completely erase or modify all the
data stored in storage device such as hard disk drive so that the data cannot be restored.
Your server contains some components that are only good for a limited period of time and
require replacement, such as fans, internal batteries, the internal DVD-ROM drive, the floppy disk drive, and the mouse. For stable operation of the server, NEC recommends you replace these components on a regular basis. Consult with your service representative for replacement or the product lives.
WARNING
Do not remove the lithium battery.
Your server contains the lithium battery. Do not remove the battery. Placing the lithium or nickel cadmium battery close to a fire or in the water may cause an explosion.
When the server does not operate appropriately due to the dead lithium battery, contact your service representative. Do not disassemble the server to replace or recharge the battery by yourself.
Mother board
Page 27
Notes on Using Your Server 1-11

USER SUPPORT

Before Asking for Repair, do the following when the server appears to fail:
1. Check if the power cord and the cables to other devices are properly connected.
2. See Chapter 8 to find if your problem fits the description. If it does, take the
recommended measure for it.
3. Check if the software required for operation of the server is properly installed.
If the server still appears to fail after you have taken the above actions, consult with your service representative immediately. Take notes on lamp indications of the server and alarm indications on the display unit before consultation, which may provide a significant help to your service representative.
Page 28
1-12 Notes on Using Your Server
Advice for Health
The longer you keep using the computer equipment, the more you become tired, which may cause disorders of your body. When you use a computer, observe the following to keep yourself from getting tired:
Good Working Posture
You have good posture if the following are satisfied when you use a computer:
You sit on a chair with your back straight.
Your hands are parallel with the floor when you put them on the
keyboard.
You look at the screen slightly lower than your eye height.
You have "good working posture" as described in the above when no part of your body is under excess strain, in other words when your muscles are most relaxed.
You have "bad posture" when you sit with your back hunched up or you operate a display unit with your face close to the screen. Bad working posture may cause eye strain or poor eyesight.
Adjustment of Display Unit Angles
Most display units are designed for adjustment of the horizontal and vertical angles. This adjustment is important to prevent the screen from reflecting bright lights and to make the display contents easy to see. You will not be able to keep "good working posture" and you will feel more tired than you should if you operate a display unit without adjusting horizontal and vertical angles.
Adjustment of Screen Brightness and Contrast
The display unit has brightness and contrast adjustment functions. The most suitable brightness and contrast depend on the individual and the working environment (well-lighted room or insufficient light). Adjust brightness and contrast so that the screen will be easy to see. An extremely bright or dark screen will give a bad effect to your eyes.
Adjustment of Keyboard Angle
The keyboard provided with the server is designed for adjustment of an angle. Adjust the keyboard angle at which the keyboard is easy to operate. The adjustment assists in reducing strain on your shoulders, arms, and fingers.
Cleaning of Equipment
Clean equipment regularly. It is difficult to see the display contents on a dusty screen. Keeping equipment clean is also important for your sight.
Fatigue and Rest
If you feel tired, you should stop working and do light exercises.
Page 29
Chapter 2

General Description

This chapter provides information that you should be familiar with before using the server. It includes names and functions of the components and features of the server.
Page 30
2-2 General Description

OVERVIEW

Your server is a modular, multiprocessing server based on the Intel® Xeon® processor family. It is a solid performer and offers the latest technology. The combination of compute performance, memory capacity, and integrated I/O provides a high performance environment for many server market applications. These range from large corporations supporting remote offices to small companies looking to obtain basic connectivity capability such a file and print services, e-mail, web access, web site server, etc. Your server is housed and available as a tower-based system.
Front View
As application requirements increase, you can expand your server with an additional memory, add­in boards and peripheral devices; tape devices, and hard disk drives. The server features the following major components.
A high-performance Intel Xeon processor
Up to 24GB of memory (using 4GB DIMMs)
Minimum configuration is 1GB of memory
Dual channel memory configuration
Five integrated I/O expansion PCI slots for add-in boards (three PCI Express slots, one
64-bit/100 MHz slot and one 32-bit/33 MHz slot)
Onboard enhanced IDE interface controller
Onboard SAS RAID controller
Onboard 1000/100/10 network controller
Four hard disk drive expansion bays
Embedded PC-compatible support (serial, parallel, mouse, keyboard, USB, LAN, and
video)
Page 31

SYSTEM CHASSIS

Names and functions of the components are shown below.

Front View

SAS Model
General Description 2-3
11
10
Additional slot 1
1
Additional slot 2
2
3
4
5
6
7
9
8
Page 32
2-4 General Description
SATA Model
11
10
Additional slot 1
1
Additional slot 2
2
3
4
5
6
7
9
8
Page 33
General Description 2-5
1 Front mask
The front mask protects the front face of the chassis.
2 DVD-ROM drive
The DVD-ROM drive reads data from the inserted CD-ROM or DVD-ROM. The drive is equipped with the following:
Open/Close button to eject the tray
Access lamp that indicates the disk access status (lights orange while being accessed)
Emergency hole to forcibly eject the tray
3 5.25-inch device bay
Backup file device of 5.25-inch width such as DAT drive or MO drive may be installed in the
5.25-inch device bay. A DVD-ROM drive is factory-installed in the bottom bay. To install a DVD-RAM drive or internal AIT (IDE), install it in the bottom bay. In this case, move the DVD-ROM drive to the additional slot 1 and connect it as a master drive.
4 Disk access lamp (green)
The disk access lamp is lit while the system accesses to an internal hard disk drive. If the internal hard disk drive is connected to the optional board, this lamp can be lit only when the LED cable provided with the server is connected.
5 POWER/SLEEP lamp (green)
Lights green when the server is powered on. Blinks green when the system is placed in the sleep mode.
6 POWER/SLEEP switch
The POWER/SLEEP switch is used to turn the power of the server ON/OFF. If you press this switch once, the power is turned on with the lamp going on green. If you press the switch again, the power is turned off.
Some OS setting can provide the function of switching to the power saving (sleep) mode. If you press the POWER/SLEEP switch once after the setting, the system enters into the power saving mode. If you press the switch again, the system returns to the normal state. (Depending on installed optional boards, the function cannot be provided.)
7 USB connectors
The USB connectors are connected with devices accepting the USB interface.
8 Stabilizer
Use the stabilizers to prevent the server from falling down. Close the stabilizers when laying the server down.
9 Hard disk drive bay
The bay can contain hard disk drives.
10 Release tabs (4 at an end of front mask)
The release tabs are provided to unlock the front mask. Press the tabs to remove the front mask.
11 3.5-inch floppy disk drive bay
The bay can contain an internal USB floppy disk drive (option).
Page 34
2-6 General Description

Rear View

6
7
11-1
11-2
10
12
45
10
8
8
10 13
1
2
3
9
1 AC inlet
The AC inlet is connected with the power cord.
2 Fixing screws (2)
Secures the left side cover.
3 Cover lock plate
Installing a theft prevention device protects the internal components of the workstation from being stolen.
2
Page 35
General Description 2-7
4 Mouse connector
The mouse connector is connected with the mouse coming with the server.
5 Keyboard connector
The keyboard connector is connected with keyboard coming with the server.
6 Serial port connector
The serial port connector is used to connect the server to a device with the serial interface. The server cannot be directly connected to a leased line through the connector.
7 Monitor connector
The monitor connector is connected with the display unit.
8 1000/100/10 lamp
1000/100/10 lamp indicates the transfer rate of LAN port.
9 100/10 lamp
100/10 lamp indicates the transfer rate of management LAN port.
LINK/ACT lamp
10
The LINK/ACT lamp shows the LAN access status.
11 LAN connector
The LAN connector is connected with a network system on LAN (1000BASE-T/100BASE­TX/10BASE-T). The value following the bold-faced number indicates the port number.
12 USB connectors
The USB connectors are connected with devices accepting the USB interface.
13 Management LAN port
Page 36
2-8 General Description

Internal View

SAS Model
3-2
12 45-16
7
8
5-2
3-1
10 9
Page 37
SATA Model
3-2
General Description 2-9
12 45-16
7
8
5-2
1 Power supply unit 2 Mother board 3 Cooling fan
3-1 Front 3-2 Rear
4 DIMMs 5 CPU heat sink
5-1 CPU 1 5-2 CPU 2 (additional)
6 DVD-ROM drive 7 5.25-inch device bay
A standard DVD-ROM drive is factory-installed in the bottom slot.
8 Hard disk drive bay
For SAS model, the HDD cage is factory installed.
9 PCI guide rail
10 3.5-inch hard disk drive (optional)
3-1
10 9
Page 38
2-10 General Description

MOTHER BOARD

20 2 4-1 3
19
1-1
1-2
4-2
18
4-5 4-4
17 16 15 13 12-5 11 10 9 8 4-3
14 12-1 to 12-4
12-6
2
5-5 5-4
6
7
5-0 to 5-3
Page 39
General Description 2-11
1
Processor socket
1-1 CPU1 socket 1-2 CPU2 socket
2
Power connectors
3
DIMM sockets (DIMM #A-1, #A-2, #A-3, #B-1, #B-2, and #B-3 from bottom to top)
4
Cooling fan connector 4-1: CPU1 heat sink fan 4-2: CPU2 heat sink fan 4-3: Front fan 4-4: Rear fan 4-5: VR fan
5
SAS connector (Not provided for SATA model. The last digit shows a channel number.)
6
Connector for RAID5 activation key
7
SAS SW RAID select jumper switch (Not provided for SATA model.) See Chapters 4 and 9 for switch setting.
8
Disk LED connector
9
USB port connector
10
USB device connector
11
IDE connector
12
Serial ATA connector (12-1 to 12-4 are not provided for SAS model. The last digit shows a channel number.)
13
Lithium battery
14
Switch/LED cable connector
15
CMOS configuration jumper switch
16
Serial port B connector (for option device)
17
IPMB connctor
18
PCI board slots (#1 to #5 from top) 18-1: PCIe ×4 18-2: 64-bit/100MHz PCI-X 18-3: PCIe ×8 18-4: PCIe ×1 (connector: ×4) 18-5: 32-bit/33MHz PCI
19
Connector for external device
20
Reserved
Page 40
2-12 General Description

STANDARD FEATURES

High performance Expandability
Dual-Core Intel High-speed 1000BASE-T/100BASE-
TX/10BASE-T interface (1Gbps/100Mbps/10Mbps supported)
High-speed disk access (SATA2) Dual channel memory configuration
High-reliability Many Available Features
BIOS password feature Temperature detection Cooling fan monitoring feature Internal voltage monitoring feature Memory monitoring feature (single-bit
error correction/double-bit error detection)
CPU/memory degradation feature Disk array (SATA2/SAS) Bus parity error detection Error notification
Xeon Processor
Large memory of up to 24GB
(six 4GB DIMMs)
USB interface (USB 2.0) Five integrated I/O expansion PCI slots
- PCI Express (x8): 1 slot
- PCI Express (x4): 1 slot
- PCI Express (x1): 1 slot
- PCI-X (64-bit/100 MHz): 1 slot
- PCI bus (32-bit/33 MHz): 1 slot
Serial ATA x6 channels
(x2 channels for SAS model)
Ultra ATA 100 x1 channel Up to two multi-processors Can be used as rack-mount type.
(N81243-64F rack conversion kit is required.)
El Torito Bootable CD-ROM (no emulation
mode) format support
Remote power-on feature AC-LINK feature Disk array (SATA) IPMI v2.0 compliant Baseboard
Management Controller (BMC)
Self-diagnosis
Power On Self-Test (POST) Test and Diagnosis
Management Utilities Easy and Fine Setup
NEC ESMPRO Off-line Maintenance Utility NEC DianaScope NEC EXPRESSSCOPE Engine
Power Saving Feature
Sleep feature
(available for Windows Server 2003)
NEC EXPRESSBUILDER (system setup
utility)
BIOS setup utility Configuration Diskette Creator
Page 41
General Description 2-13

Power Supply

The system contains one auto-sensing 600-watt power supply at an operating frequency of 50/60 Hz.
The power supply is designed to comply with existing emission standards and provide sufficient power for a fully loaded system configuration.

Peripheral Bays

The system supports a variety of standard PC AT-compatible peripheral devices. The chassis includes these peripheral bays:
Three 5.25-inch file bays for installing 5.25-inch peripheral devices such as an optional
tape drives. (A DVD-ROM drive is factory-installed.)
The 3.5-inch device bays for installing up to four SATA or SAS hard disk drives.

Remote Power-On Feature (Wake On LAN)

The remote power-on function turns on the server through a network. It sends a special packet from the management computer to a remote server to turn it on if the server is off-powered.
To enable this feature, you must select "Enabled" for each submenu in the Power Management Setup of the Advanced menu of the BIOS setup utility, "SETUP." (See Chapter 4.)
The remote power-on feature is not available in the following cases. Press the POWER/SLEEP switch once to start the OS, and turn off the server in an appropriate procedure.
Abnormal previous system shut-down
No power supply to the server (due to turned-off breaker, disconnected power cord, power
blackout, etc.)

AC LINK Feature

When the power cord of the server is connected to an uninterruptible power supply (UPS) unit, the server supports the power linkage feature that enables control over the power supply from the UPS to the server. The AC LINK feature can be enabled or disabled with Power Management Setup in the Server menu of the BIOS setup utility, "SETUP." (See Chapter 4.)

Security

The BIOS setup utility provides a number of security features to prevent unauthorized or accidental access to the system. Once the security measures are enabled, access to the system is allowed only after the user enters the correct password(s). For example:
Set and enable an administrative password.
Set and enable a user password
Check the user account when entering the BIOS setup utility or booting the system.
Page 42
2-14 General Description

NEC EXPRESSBUILDER

The CD-ROM that comes with the server contains a setup utility called "NEC EXPRESSBUILDER."
The major functions of the NEC EXPRESSBUILDER are:
To install the Operating System.
"Express Setup" helps you to install the Windows Operating System. (See Chapter 5)
To diagnose the system.
NEC EXPRESSBUILDER includes the System Diagnostics to check your server. (See Chapter 6)
To create support disks.
Use this function to create the support disks used to boot the utilities from the floppy disk, or the OEM floppy disk used for a manual installation of Windows. (See Chapter 6)
To update the BIOS.
Use this function to update the system BIOS or firmware of the server. (See Chapter 6)
To update the Windows System*
"Update Express5800 system" in Master Control Menu (Windows-based NEC EXPRESSBUILDER feature) updates the several drivers of Microsoft Windows. (See Chapter 6)
To install the utilities.
NEC EXPRESSBUILDER includes some management software for Windows (NEC ESMPRO, NEC DianaScope and so on) and maintenance utilities for DOS (System diagnostics, Off-line Maintenance Utility and so on).
You can install the applications for Windows from Master Control Menu and install the utilities for DOS from Tools menu. (See Chapter 6)
To read the online documents*
You can refer to the online documents from Master Control Menu. (See Chapter 6)
* These functions are available under the Windows system.
NOTE: Some features among those listed above can be used from the
remote computer via cross cable (COM), or LAN. See Chapter 6 for details.

NEC ESMPRO

The NEC ESMPRO is server management software that runs on the OS. The NEC ESMPRO includes the NEC ESMPRO Manager for the server monitoring terminal and the NEC ESMPRO Agent for the NEC Express server.
NOTE: For details of major functions of the NEC ESMPRO, system
configuration and setups with the NEC ESMPRO, see Chapter 6. Available functions of the NEC ESMPRO depend on the OS you install. Ask your service representative for details.
Page 43
General Description 2-15

Off-line Maintenance Utility

The Off-line Maintenance Utility is used for maintenance and fault analysis of the server. This utility is usually used by the service representative. See Chapter 8 for details.

System Diagnostic Utility

The system diagnostic utility contained in the NEC EXPRESSBUILDER is useful to detect hardware failures. See Chapter 7 for details.

Remote Management

The server may be monitored and managed via LAN/WAN by installing the optional Remote Management (N8115-03) and NEC DianaScope utility. To use the NEC DianaScope, a separately priced server license is required.
The Remote Management performs the following:
Monitoring of temperature, voltage, and fans
Generation of SEL (system event log) at occurrence of hardware failure
Monitoring of OS stall by using watchdog timer
Notification after occurrence of OS stop error
Remote management via LAN/WAN by using NEC DianaScope (e.g., resetting the server,
power on/off, viewing System Event Log (SEL))
NOTES:
Notes on using Remote Management (N8115-03)
– Booting the server from the NEC EXPRESSBUILDER CD by
using the Remote Media function is not available.
– For the latest information about Remote Console/Remote Media
function, visit our web site.
The following functions are not supported in the command line
interface of EXPRESSSCOPE Engine.
– Power state acquisition
– STATUS LED state acquisition
Page 44
2-16 General Description

USING YOUR SERVER

This section describes basic operations of your server including how to use devices such as the floppy disk drive and the DVD-ROM drive. See Appendix B for notes on using the floppy disk, CD­ROM, and accessories including the keyboard and the mouse.

POWER Switch

Use the POWER/SLEEP switch to turn on/off the server.
Power On
Press the POWER switch on the front of the computer chassis.
The POWER/SLEEP lamp lights in green.
IMPORTANT:
If the power cord is connected to a power control device such as a
UPS (Uninterruptible Power Supply), make sure that the power control device is powered.
Do not turn off the server until characters appear on the screen.
Page 45
General Description 2-17
POST
POST (Power On Self-Test) is the self-diagnostic program stored in the system memory.
When you power on the server, the system automatically runs POST to check the mother board, ECC memory module, CPU module, keyboard, and mouse. POST also displays messages of the BIOS Setup utility, such as the start-up message, while in progress.
With the factory setup of the server, the NEC logo appears on the display unit while POST is in progress. (To display the POST check results, press Esc.)
You don't always need to check the POST check results. Check messages that POST displays when:
you use the NEC Express server for the first time.
the server appears to fail.
the server beeps for many times between power-on and OS start-up.
an error message appears on the display unit.
Page 46
2-18 General Description
POST Execution Flow
The following describes the progress of POST in the chronological order.
IMPORTANT:
Do not power off the server while POST is in progress.
Do not make key entries or perform mouse operations while POST
is in progress.
Some system configurations may display the message "Press Any
Key" to prompt a key entry. This message is driven by BIOS of an installed optional board. Make sure to read the manual that comes with the optional board before any key entry.
Powering on the server, after you installed or removed an optional
PCI board or moved it to another slot, may display the message that indicates incorrect board configuration and suspend POST. In such a case, press F1 to continue POST. Board configuration can be made using the utility described later.
1. After a few seconds from power-on, POST starts checking the memory. The count
message of the basic and expansion memory appears at top left on the display unit screen. The memory check may takes a few minutes to complete depending on the memory size of the server. Also, it may take approximately one minute for the screen display to appear after rebooting the server.
2. Some messages appear upon completion of the memory check. These messages appear to
indicate that the system has detected the CPU, keyboard, and mouse.
3. After a few seconds, POST displays the following message prompting you to launch the
BIOS SETUP utility, stored in the system memory of the server. This message appears at bottom left on the screen.
Press <F2> to enter SETUP or Press <F12> to boot from Network
Launch the BIOS setup utility when you need to change the settings to meet the requirements for the server. As long as the above message is not displayed with an error message, you don't have to launch the utility. (Ignore the message. POST will automatically proceed.)
To launch the BIOS setup utility, press F2 while the above message is displayed. See Chapter 4 for setup and parameters.
The server automatically restarts POST all over again when you exit the SETUP utility.
4. If your server uses onboard SAS RAID feature, the following message is displayed on the
screen to prompt you to run the utility.
Press Ctrl-M to run LSI Logic Software RAID Setup Utility
Press Ctrl + M to run the utility. For detail explanation, see Chapter 4 for detail.
Page 47
General Description 2-19
5. If the POST detects the optional add-in card, it display the message prompting you to
launch the add-in card BIOS configuration utility. (Ignore the message. POST will automatically proceed a few seconds later.)
Refer to the manual that comes with the optional add-in card for detail.
6. If you set a password using the BIOS SETUP utility, the password entry screen appears
upon successful completion of POST.
Up to three password entries will be accepted. Three incorrect password entries disable the server to boot. In such a case, turn off the power and wait about ten seconds before turning on to boot the server.
IMPORTANT: Do not set a password before installing an OS.
7. The OS starts when POST completes.
POST Error Messages
When POST detects an error, it displays an error message on the display unit screen or emits beep code. See Chapter 8 for POST error codes.
IMPORTANT: Take a note on the messages displayed before
consulting with your service representative. Alarm messages are useful information for maintenance.
Page 48
2-20 General Description

Power Off

Follow the procedure below to power off the server. If the power cord of the server is connected to a UPS, refer to the manual that comes with the UPS or the manual for the application that controls the UPS.
IMPORTANT: Always allow POST to complete before turning off the server.
1. Shut down the OS.
2. Press the POWER/SLEEP switch on the front of the server.
The POWER/SLEEP lamp goes out.
3. Power off peripheral devices.
NOTE: The standby function of Windows Server is not available. Do
not select "Standby" in the Windows shutdown menu.

SLEEP Switch

The POWER/SLEEP switch allows you to save almost all power of the server (power-saving mode or sleep mode).
Press the POWER/SLEEP switch on the front of the server to place the server in the power-saving mode. (The POWER/SLEEP lamp blinks.) In the power-saving mode, the server retains the memory data and the status of the previous operations.
To resume the original state, press the POWER/SLEEP switch again. (It may take a little time to resume the original state.)
NOTE: The operational level in the power-saving mode depends on
the OS in use. (Available for Windows Server 2003.)
Page 49
General Description 2-21

DVD-ROM Drive

The server is provided with the DVD-ROM drive on its front to read data from a disc.
CAUTION
Observe the following instructions to use the server safely. Failure to follow these instructions may cause a fire, personal injury, or property damage. See pages 1-3 to 1-8 for details.
Do not leave the tray ejected from the DVD-ROM drive.
Take off the headphone before you plug in the headphone jack.
Setting and Removing the Disc
Make sure that the power of the server is on (with the POWER/SLEEP lamp being lit in
1.
green) before setting the disc on the DVD-ROM drive.
2. Press the Open/Close button on the front of the DVD-ROM drive.
The tray comes out.
3. Put the disc on the tray carefully and securely with the character printed surface facing
upward.
4. Press the Open/Close button or gently push on the tray front.
The tray is automatically retracted into the DVD-ROM drive.
IMPORTANT: If a noisy sound in driving the DVD-ROM drive occurs after setting a disc, set it again correctly.
To take out the disc from the DVD-ROM drive, press the Open/Close button in the similar way in setting the disc to make the tray go out. If the access LED is lit in orange, the disc is being accessed. Confirm that the access LED is not lit before pressing the Open/Close button.
Your OS may have a command to eject the tray.
When you have taken out the disc, retract the tray back in place.
Page 50
2-22 General Description
When you fail to eject:
When you fail to eject the tray with the Open/Close button and take out the disc from the server, follow the procedure below.
1. Press the POWER switch to power off the server. (The POWER/SLEEP lamp goes off.)
2. Insert a metal pin of approximately 1.2 mm in diameter and 100 mm in length (a
straightened large paper clip will make a substitute) into the emergency hole on the front of the DVD-ROM drive and gently push it in until the tray is ejected.
Emergency hole
IMPORTANT:
Do not use a toothpick or plastic stick that is easy to break.
If the above procedure does not let you take out the DVD/CD-ROM,
contact your service representative.
3. Hold the tray and pull it out.
4. Take out the disc.
5. Push the tray back into position.
Page 51
General Description 2-23
Use of the Disc
Keep the following notes in mind to use the disc for the server:
For the disk which does not conform to the CD standard, the playback of such a disk with
the CD drive is not guaranteed.
Do not drop the disc.
Do not place anything on the disc or bend the disc.
Do not attach any label onto the disc.
Do not touch the signal side (nothing is printed on this side) with your hand.
Place the disc with its printed side upward and gently put it on the tray.
Do not scratch the disc or write anything directly on it with a pencil or ball-point pen.
Keep the disc away from cigarette smoke.
Do not leave the disc in a high-temperature place (e.g., place exposed to direct sunlight or
close to a heater).
When dust or fingerprints are attached on the disc, wipe the disc from its center to edge
with a dry soft cloth slowly and gently.
Use the CD cleaner to clean the disc. Do not use record spray/cleaner, benzene, or thinner.
Keep the disc in a disc case when not in use.
If the disc emits large noise in the DVD-ROM drive, remove the disc and insert it back
again.
Page 52
2-24 General Description
(This page is intentionally left blank.)
Page 53
Chapter 3

Setting Up Your Server

This chapter describes how to set up your server appropriate for your system, on a step-by-step basis.
Page 54
3-2 Setting Up Your Server

SETUP FLOW

Follow the flowchart below to set up the server.
Unpacking the system
Unpack the server and accessories from the shipping carton box.
Installing optional devices
If you have purchased any optional device for the server, see Chapter 9 to install it.
Selecting the server site
Select a suitable site for the server.
Connecting peripheral devices
Connect peripheral devices to the server.
Connecting the power cord
Connect the power cord to the server.
Turning on the server
Power on the server to start software setups. Setups depend on the optional internal devices installed and the peripheral devices connected.
Installing the operating system
Install an operating system to the server. See Chapter 5.
Installing the utilities
Install the utilities in the provided NEC EXPRESSBUILDER CD-ROM. See Chapter 6.
Making backup copies of system information
After all the system setup procedures are completed, make backup copies of system information. System information is required for recovering the server from the trouble or after replacing the system board.
Page 55
Setting Up Your Server 3-3

UNPACKING THE SYSTEM

When you receive your system, inspect the shipping containers prior to unpacking. If the shipping boxes are damaged, note the damage, and if possible, photograph it for reference. After removing the contents of the containers, keep the cartons and the packing materials. If the contents appear damaged when you unpack the boxes, file a damage claim with the carrier immediately.

INSTALLING OPTIONAL DEVICES

To install any optional device, see Chapter 9, "Upgrading Your Server," for the installation procedure. Proceed to the next section if you have no optional devices to install.
IMPORTANT: There are third-party products (memory modules, hard
disk drives, etc.) available for the server in the markets. However, NEC recommends that you should use NEC products for stable operation. NEC assumes no liability for data errors and failures due to malfunction of the server resulted from installation of those third-party products.
Page 56
3-4 Setting Up Your Server
A
A

SELECTING SERVER SITE

Read the following precautions before selecting a suitable site for your server. The following describes installation of the server and connections to the server.
CAUTION
Observe the following instructions to use the server safely. Failure to follow these instructions may cause a fire, personal injury, or property damage. See pages 1-3 to 1-8 for details.
Never attempt to lift the server only by yourself.
Do not install the server in any place other than specified.
The following figure illustrates a site suitable for installing the server.
Room that satisfies the following conditions: * <While operating> Temperature: 10 to 35ºC
Humidity: 20 to 80% Temperature gradient: ±10ºC/h
tmosphere: 749 to 1040 hpa <While halting> Temperature: –10 to 55ºC Humidity: 10 to 80% Temperature gradient: ±15ºC/h
tmosphere: 749 to 1040 hpa
100 to 120 Vac/200 to 240 Vac parallel bi-polar wall power outlet with the ground line.
Allow clearance of at least 150 mm in
front of and behind the server.
The server must be
fixed with stabilizers.
* It is recommended that the server should be used in a room where
temperature is in the range between 15 to 25ºC.
Clean and tidy room
Close enough to connect the
mouse and the display.
Install the server on
a flat, rigid desk
Page 57
Setting Up Your Server 3-5
When you have selected a server site, hold the server by its bottom with at least three persons and carry it to the site, then place it slowly and gently.
IMPORTANT: Do not hold the server by its front mask to lift the
server. The front mask may be disengaged and damage the server.
Do not install the server in the following locations as it may cause malfunctions of the server.
Places with drastic changes in temperature (e.g., near a heater, air conditioner, or
refrigerator)
Places with strong vibration
Places with corrosive gas in presence, near chemicals, or with possibilities of chemicals
sprayed over
On a non-antistatic carpet
Places with possibilities of falling objects
Places where a power outlet that shares the ground line with another (especially the one to
which a device with large power consumption is connected) must be used for the server
Places near a device generating intense magnetic field (such as a TV, radio,
broadcast/communication antenna, power transmission wire, and electromagnetic crane) is placed
Places near equipment that generates power noise (e.g., contact spark at power-on/power
off of commercial power supply through a relay). If you must install the server close to such equipment, request your service representative for separate power cabling or noise filter installation.
Page 58
3-6 Setting Up Your Server

CONNECTING PERIPHERAL DEVICES

Connect peripheral devices to the server. The server is provided with connectors for wide variety of peripheral devices. The figure on the next page illustrates available peripheral devices for the server in the standard configuration and locations of the connectors for the devices.
CAUTION
Observe the following instructions to use the server safely. Failure to follow these instructions may cause a fire, personal injury, or property damage. See pages 1-3 to 1-8 for details.
Do not use any damaged cable connector.
Do not use any unauthorized interface cable.
Do not use the server with any loose interface connection.
Do not step on the interface cable or place any heavy object on it.
IMPORTANT:
Power off the server and a peripheral device before connection.
Connecting a powered peripheral device to the powered server will cause malfunctions and failures.
To connect a third-party peripheral device or interface cable to the
server, consult with your service representative for availability of such a device or cable. Some third-party devices may not be used for the server.
To connect the provided keyboard and mouse, plug their connectors
to the server with the "" mark on the connectors facing right.
Do not connect the serial ports with the telephone line directly.
Do not connect any devices to the connectors not instructed in this
subsection. Doing so could damage the device, your server, or both.
Page 59
FRONT
Setting Up Your Server 3-7
Device with the USB interface
(e.g., terminal adapter)
REAR
Keyboard
Device with the serial interface (e.g., modem)*
Display unit
Device with the USB interface
Mouse
(e.g., terminal adapter)
Finally connect the power cord to the receptacle.
Hub (multiport repeater)
LAN ports (1000BASE-T/ 100BASE-TX/ 10BASE-T)
Management LAN port (100BASE-TX/10BASE-T)
Hub (multiport repeater)
Page 60
3-8 Setting Up Your Server

CONNECTING POWER CORD

Connect the provided power cord to the server.
Observe the following instructions to use the server safely. Failure to follow these instructions may result in death or serious personal injury. See pages 1-3 to 1-8 for details.
Do not hold the power plug with a wet hand.
Observe the following instructions to use the server safely. Failure to follow these instructions may cause a fire, personal injury, or property damage. See pages 1-3 to 1-8 for details.
Do not plug the power cord in to an improper power source.
Do not connect the power cord to an outlet that has an illegal number of
connections.
Insert the power plug into the outlet as far as it goes.
Use the authorized power cord only.
WARNING
CAUTION
1. Plug the provided power cord into the power receptacle on the rear of the server.
2. Plug the other end of the power cord into the wall outlet.
Page 61
Setting Up Your Server 3-9
NOTES:
To connect the power cord from the server to an interruptive power
supply (UPS), use service outlets on the rear of the UPS. Refer to the manual that comes with the UPS for details.
Connect the battery connector when using UPS. Disconnect the connector when moving the UPS to relocate it.
When the power cord from the server is connected to a UPS, change
the BIOS SETUP utility of the server to link with power supply from the UPS. Change a parameter for "AC-LINK" of the Server menu of the BIOS SETUP utility. See Chapter 4 for details.
Page 62
3-10 Setting Up Your Server

TURNING ON THE SERVER

Turn on the server and follow the on-screen instructions for setup.
IMPORTANT: Before turning on the server:
Some optional boards require setups with the BIOS setup utility
before installation. If the server has a PCI board with the PCI-to­PCI bridge installed, the BIOS setup utility is enabled to launch. Check on the board specifications to find out whether it requires pre-installation setups before actually installing the board.
Some installed optional devices or connected peripheral devices
require setups before proceeding to the next step.
To use the server with no optional devices installed besides the graphic board, install a desired OS to the server.
1. Make sure all external devices, such as a video display, keyboard, and mouse have been
connected, and the power cords are connected.
2. Power on the video display and any other external devices.
3. Make sure that the floppy disk drive contains no floppy disk and the DVD-ROM drive
contains no bootable DVD/CD-ROM.
4. Press the POWER/SLEEP switch.
NOTES:
If the power cord is connected to the power control unit such as the
UPS, turn on the power control unit.
Connect the power cord and wait a few seconds before pressing the
POWER switch. The POWER/SLEEP switch does not work in a few seconds after connecting the power cord due to firmware start­up.
Page 63
Setting Up Your Server 3-11
The POWER/SLEEP lamp on the front of the server comes on.
In a few seconds, the NEC logo appears on the screen and the Power On Self-Test (POST) begins.
The POST runs automatically when you power on the server or reset it with a keyboard operation (Ctrl + Alt + Delete). The POST runs diagnostics, initializes the server, sets interrupt vectors, detects installed peripheral devices, and boots the operating system (if installed). See Chapter 2 for detailed description on POST.
If the server halts before completing the POST, the POST emits a beep code indicating a fatal system error requiring immediate attention. (See Chapter 8, "Troubleshooting," for troubleshooting information.)
During memory test, the POST displays the amount of memory it was able to access and test. Depending on the amount of installed memory, it may take several minutes to complete the memory test.
NOTE: The factory-set is defined to hide the POST screen with the
NEC logo screen. You can always change the NEC logo screen to the POST screen by pressing Tab. To change the start-up screen, use the BIOS setup utility. (See Chapter 4 for details.)
During the POST, you will see the banner message to prompt you to launch the BIOS setup utility stored in ROM on the mother board or on an installed option board.
Start the BIOS setup utility appropriate to your system environment to change the CMOS Setup. For detail explanation on the BIOS setup utility for the server, see Chapter 4. For the BIOS utility for the option board, refer to the manual that comes with the option board.
IMPORTANT: Always allow POST to complete before turning off
your system.
Page 64
3-12 Setting Up Your Server

INSTALLING OPERATING SYSTEM

See Chapter 5 for installing Microsoft Windows Server 2003.
To install the other operating system, contact your service representative.

INSTALLING UTILITIES

Install the utilities that come with the server. See Chapter 6 for details.

MAKING BACKUP COPIES OF SYSTEM INFORMATION

The system information includes the current BIOS settings and any specific information for the server.
Save the information after completing the system setup.
Without the backup data, you will not be able to recover the information.
You can save the information by the following process.
1. Insert the "NEC EXPRESSBUILDER" CD-ROM into the DVD-ROM drive and reboot
the system.
2. Select [Tools].
3. Select [Off-line Maintenance Utility].
4. Select [System Information Management].
5. Insert a floppy disk into the floppy disk drive.
6. Select [Save].
Page 65
Chapter 4

Configuring Your Server

Configuration and setup utilities are used to change your system configuration. You can configure your system, as well as option boards you may add to your system, using the BIOS Setup utility. Several unique system parameters are configured using the BIOS Setup utility, which is stored in the system FLASH memory.
If your system has been factory configured, the BIOS Setup utility or RAID Configuration Utility do not need to be run unless you want to change the password or security features, add certain types of option boards or devices, or upgrade your mother board.
This chapter also provides information on several system configuration parameters that are set by jumpers on the system board. However, these parameters do not usually require change.
Use NEC EXPRESSBUILDER CD-ROM to create the device driver diskettes.
Page 66
4-2 Configuring Your Server

SYSTEM BIOS (BIOS SETUP UTILITY)

The BIOS Setup utility is provided to make basic hardware configuration for the server. This utility is pre-installed in the flash memory of the server and ready to run.
The server is configured with the correct parameters using the BIOS Setup utility and shipped in the best conditions. Thus, you don't need to use the BIOS Setup utility in most cases. However, you might wish to use the BIOS Setup utility in the cases described below.
IMPORTANT:
The BIOS Setup utility is intended for system administrator use
only.
The BIOS Setup utility allows you to set a password. The server is
provided with two levels of password: Supervisor and User. With the Supervisor password, you can view and change all system parameters of the BIOS Setup utility. With the User password, system parameters available for viewing and changing are limited.
Do not set any password before installing the OS.
The server contains the latest version of the BIOS Setup utility.
Dialog boxes appear on your BIOS Setup utility, thus, may differ from descriptions in this manual. If you find anything unclear, see the online help or ask your service representative.
Page 67
Configuring Your Server 4-3

Starting SETUP Utility

A few seconds after powering on, the following message appears at bottom left on the screen. If NEC logo appears instead, press Esc.
Press <F2> to enter SETUP or Press <F12> to boot from Network
Press F2 to start the BIOS Setup utility and display its Main menu.
If you have previously set a password with the BIOS Setup utility, the password entry screen appears. Enter the password.
Enter password:[ ]
Up to three password entries will be accepted. If you fail to enter the password correctly for three consecutive times, the server halts. (You can no longer proceed.) Power off the server.
NOTE: The server is provided with two levels of password:
Supervisor and User. With the Supervisor password, you can view and change all system parameters. With the User password, system parameters available for viewing and changing are limited.
Page 68
4-4 Configuring Your Server

Description on On-Screen Items and Key Usage

Use the following keyboard keys to work with the BIOS Setup utility. These keys are also listed at the bottom of the menu screen.
Indicates there are submenus.
Setup item menu
Explanation of key functions menu
Cursor (↑, ):
Move cursor up and down. The cursor moves only to the settings
Indicates the current menu.
Online help window
Parameter (high-lights upon selection) menu
that you can change.
Cursor (←, →): – and +: Enter Esc
Move between menus. Select the previous value (–) or the next value (+) for the field. Execute command or select ³ submenu. Exit the current menu and return to the previous menu.
F1: Get Help about an item. Press Esc to return to the previous menu. F9: F10:
Load default configuration values for this menu. Save configuration values and exit.
Page 69
Configuring Your Server 4-5

Configuration Examples

The following describes examples of configuration required to use software-link features or for system operations.
Time and Date Settings
You can also change the time and date settings via the operating system commands.
Select [Main] - [System Time].
Select [Main] - [System Date].
Link with Management Software
To control power supply of the server with NEC ESMPRO Manager via the network
Select [Advanced] - [Advanced Chipset Control] - [Wake On LAN/PME] - [Enabled].
Select [Server] - [AC LINK] - [Stay Off].
Hard Disk Drive
To check the hard disk drive status
Select [Main] - [Primary IDE Master] and check the status indications.
To configure the SW RAID (on-board) with SATA hard disk drives
Select [Advanced] - [Peripheral Configuration] - [SATA Controller Mode Option] ­[Enhanced]. Then select [Advanced] - [Peripheral Configuration] - [SATA RAID] ­[Enabled], and configure the RAID drive.
IMPORTANT: Be sure to set to [Enabled] after executing [Load
Setup Defaults] or CMOS clear. Leaving this parameter as the factory­set value (Disabled) may destroy the data in hard disk drive.
UPS
To link power supply with the UPS
To power on the server when power is supply from the UPS
Select [Server] - [AC LINK] - [Power On].
To keep the server off-powered even when power is supplied from the UPS
Select [Server] - [AC LINK] - [Stay Off].
To keep the server off-powered even when power is supplied from the UPS if the POWER
switch was used to power off
Select [Server] - [AC LINK] - [Last State].
Page 70
4-6 Configuring Your Server
Boot
To change the boot order of devices connected to the server
Select [Boot] and specify the boot order.
To control from the remote console
Select [Server] - [Console Redirection] and set each item.
Memory
To check the installed memory (DIMM board) status
Select [Advanced] - [Memory Configuration] and check the status indications.
The on-screen DIMM group numbers and socket locations on the mother board are associated as shown in the following figure.
DIMM #B-3 DIMM #B-2 DIMM #B-1 DIMM #A-3 DIMM #A-2 DIMM #A-1
CPU #1
Motherboard
To clear the memory (DIMM board) error information
Select [Advanced] - [Memory Configuration] - [Memory Retest] - [Yes] and reboot.
To run power-on memory test
Select [Advanced] - [Memory Configuration] - [Extended RAM Step] - [1MB] and reboot.
CPU #2
FRONTREAR
Page 71
CPU
To check the installed CPU status
Select [Main] - [Processor Settings] and check the status indications.
The on-screen processor numbers and socket locations on the motherboard are associated as shown in the figure on the previous page.
To clear the CPU error information
Select [Main] - [Processor Settings] - [Processor Retest] – [Yes] and reboot.
Keyboard
To set Numlock
Select [Advanced] - [Numlock] – [On]/[Off].
Event Log
To clear event logs
Select [Server] - [Event Log Configuration] - [Clear all Event Logs], press Enter, and select [Yes].
Configuring Your Server 4-7
Security
To set passwords on the BIOS
Select [Security] - [Set Supervisor Password] and enter a password.
Select [Security] - [Set User Password] and enter a password.
Set Supervisor password first, then User password.
External Devices
To set up external devices
Select [Advanced] - [Peripheral Configuration] and set up each device.
Internal Devices
To install the disk array controller board or SCSI controller board
Select [Advanced] - [PCI Configuration] - [PCI Slot n Option ROM] - [Enabled]. n: slot number
To clear the hardware configuration data (after installing/removing internal devices)
Select [Advanced] - [Reset Configuration Data] - [Yes].
Page 72
4-8 Configuring Your Server
Saving the Configuration Data
IMPORTANT:
configured with the on-board HostRAID, be sure to select [Advanced] ­[Peripheral Configuration] - [SATA Controller Mode Option] ­[Enhanced]. Then, select [Advanced] - [Peripheral Configuration] ­[SATA RAID Enable] - [Enabled]. Leaving this parameter as the factory-set value (Disabled) may destroy the data in hard disk drive.
To save the current configuration data
Select [Exit] - [Exit Saving Changes] or [Save Changes].
To discard changes to the current configuration data
Select [Exit] - [Exit Discarding Changes] or [Discard Changes].
To load the user-defined default
Select [Exit] - [Load Setup Defaults].
To load the custom defaults
Select [Exit] - [Load Custom Defaults].
To save the custom defaults
Select [Exit] - [Save Custom Defaults].
If the SATA hard disk drives are used in disk array
Page 73
Configuring Your Server 4-9

Menu and Parameter Descriptions

The SETUP utility has the following six major menus:
Main
Advanced
Security
Server
Boot
Exit
To set minute functions, select a submenu from the above menus. The following describes available functions and parameters, as well as the factory-set, for each menu.
Main
If BIOS SETUP is started, the Main menu appears first. If you select a menu item preceded by symbol ³ and press Enter, the appropriate submenu appears.
Page 74
4-10 Configuring Your Server
The items which can be set on the Main menu screen and their functions are described below.
Option Parameter Description Your Setting
System Time HH:MM:SS Set the system time. System Date MM/DD/YYYY Set the system date. Hard Disk Pre-Delay [Disabled]
3 seconds 6 seconds 9 seconds 12 seconds 15 seconds 21 seconds
30 seconds Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave
Processor Settings Shows the processor settings
Language [English (US)]
Français
Deutsch
Español
Italiano
Allows slower spin-up drives to come ready.
Shows the information on the device connected to each channel on the submenu. If only one hard disk drive is connected to serial ATA channel, the information is displayed on area for Primary IDE. The settings of some items may be changed. However, leave the items as they are at the shipment.
submenu. See the next page. Select which language BIOS displays.
[ ]: Factory-set
IMPORTANT: Check and adjust the system clock before the
operation if any of the following conditions is applicable.
After carriage of deviceAfter storage of deviceAfter the device is entered into the pause state under the
environmental condition enduring device operation (temperature:
10°C - 35°C, humidity: 20% - 80%) Check the system clock at the rough rate of once per month. When the system clock is installed in a system requiring high time precision, it is
recommended to use a time server (NTP server).
If the system clock is remarkably delayed or advanced as the passage of time in spite of adjustment, contact your service representative for maintenance.
Page 75
Configuring Your Server 4-11
Processor Settings
If you select "Processor Settings" on the Main menu, the screen shown below appears.
See the table below for the items.
Option Parameter Description Your Setting
Processor Retest [No]
Yes
Processor Speed Setting
Processor 1 CPUID
Processor 1 L2 Cache
Processor 2 CPUID
Processor 2 L2 Cache
nnn GHz
Numeral (0Fxx) Disabled Not Installed
Numeral (0Fxx) Disabled Not Installed
If you select [Yes], BIOS will clear historical processor status and retest all the processors on the next boot. This parameter is automatically reset to "No" at the next boot.
Displays clock speed for the processor. (View only)
Displays CPU ID for processor 1. "Disabled" indicates that the processor
is defected. "Not Installed" indicates that no CPU is installed. (View only) Displays L2 cache size for processor 1.
Displays CPU ID for processor 2. "Disabled" indicates that the processor
is defected. "Not Installed" indicates that no CPU is installed. (View only) Displays L2 cache size for processor 2.
Page 76
4-12 Configuring Your Server
Option Parameter Description Your Setting
Execute Disable Bit
Intel(R) Virtualization Tech
[Disabled] Enabled
[Disabled] Enabled
Displayed only when the CPU supports Execute Disable Bit. Specify whether to enable or disable this feature.
Specify whether to enable or disable the virtualization technology of Intel processor.
[ ]: Factory-set
Page 77
Configuring Your Server 4-13
Advanced
The Advanced menu appears if you move the cursor to the position of "Advanced."
If you select a menu item preceded by symbol
³ and press Enter, the appropriate submenu appears.
See the table below for the items.
Option Parameter Description Your Setting
Memory Configuration
PCI Configuration Displays submenu. Peripheral
Configuration Advanced Chipset
Control Boot-time
Diagnostic Screen
Reset Configuration Data
NumLock On
Memory/Processor Error
Displays submenu.
Displays submenu.
Displays submenu.
[Disabled] Enabled
[No] Yes
[Off] [Boot] Halt
Specify whether the power-on self-test (POST) running screen is displayed or not on booting. If disabled, the BIOS will display the NEC logo during POST. Press Esc to switch to the POST running screen.
Select "Yes" if you want to clear the system configuration data stored in POST. This parameter is automatically reset to "No" at the next boot.
Specify whether to enable or disable the Numlock feature at system start-up.
Specify whether to stop POST execution if a memory or processor error was detected during POST.
[ ]: Factory-set
Page 78
4-14 Configuring Your Server
Memory Configuration
The following screen appears if you select "Memory Configuration" on the Advanced menu.
See the table below for the items.
Option Parameter Description Your Setting
System Memory Extended Memory DIMM Group #1 Status DIMM Group #2 Status DIMM Group #3 Status
Memory Retest
Extended RAM Step
Sparing [Disabled]
Indicates the total capacity of the base
memory. (View only)
Indicates the total capacity of the memory
available for OS. (View only) Normal Disabled Not installed
[No] Yes
1MB 1KB Every location [Disabled]
Enabled
Indicates the current memory status. (View
only)
"Normal" indicates that the memory devices
operate normally.
"Disabled" indicates that one or more memory
devices are defected.
"Not Installed" indicates that no memory
devices are installed.
On-screen group numbers and DIMM
slockets on mother board are associated as
follows.
Group #1: DIMM #A-1, #B-1
Group #2: DIMM #A-2, #B-2
Group #3: DIMM #A-3, #B-3
Each group is composed of two DIMMs of
interleave type.
If you select [Yes], BIOS will clear historical
memory status and retest all the DIMMs on
the next boot. This parameter is automatically
reset to "No" at the next boot.
Specify whether to execute a memory test for
extended memory or not. If the test is
executed, specify the block size.
Specify whether to enable or disable online
spare memory feature.
[ ]: Factory-set
Page 79
Configuring Your Server 4-15
PCI Configuration
The following screen appears if you select "PCI Configuration" on the Advanced menu. If you select a menu item preceded by symbol
³ and press Enter, the appropriate submenu appears.
See the table below for the items.
Option Parameter Description Your Setting
PCI Slot 1 - 5 Option ROM
[Enabled] Disabled
Displays the submenu to specify whether to enable or disable the BIOS on the device (board) connected to PCI slot.
Set this item to "Enabled" when:
installing graphics accelerator board
the disk array controller or SCSI controller
is connected with the hard disk drive which contains an OS
Set this item to "Disabled" when:
the LAN controller which contains ROM
BIOS is used but the board does not
provide network booting. Disabling Option ROM Scan saves memory consumption and time for startup.
[ ]: Factory-set
Page 80
4-16 Configuring Your Server
– Onboard Video Controller
Option Parameter Description Your Setting
VGA Controller [Enabled]
Disabled
Onboard VGA Option ROM Scan
[Auto] Force
Specify whether the onboard video controller is enabled or disabled.
Specify whether to execute option ROM scan of onboard video controller automatically or forcibly.
[ ]: Factory-set
– Onboard LAN
Option Parameter Description Your Setting
LAN Controller Disabled
[Enabled] LAN1 Option ROM Scan LAN2 Option ROM Scan
Disabled
[Enabled]
Disabled
[Enabled]
Specify whether the onboard LAN controller is enabled or disabled. Specify whether the BIOS scan of onboard LAN controller 1 is enabled or disabled. Specify whether the BIOS scan of onboard LAN controller 2 is enabled or disabled.
[ ]: Factory-set
Page 81
Configuring Your Server 4-17
Peripheral Configuration
The screen shown below appears if you select "Peripheral Configuration" on the Advanced menu. If you select a menu item preceded by symbol
³ and press Enter, the appropriate submenu appears.
See the table below for the items.
IMPORTANT: Note that the interrupt and/or base I/O address does
not conflict with others. If the value set for the interrupt or base I/O address is used in another resource, the yellow asterisk (*) appears. Reassign any item with the yellow asterisk properly.
Option Parameter Description Your Setting
Serial Port A Disabled
[Enabled]
Base I/O address [3F8]
2F8 3E8 2E8
Interrupt IRQ 3
[IRQ 4]
Serial Port B Disabled
[Enabled]
Base I/O address 3F8
[2F8] 3E8 2E8
Interrupt [IRQ 3]
IRQ 4
USB 2.0 Controller Disabled
[Enabled]
Selects whether serial port A is enabled or disabled.
Selects the base I/O address for serial port A.
Selects the interrupt for a serial port A.
Selects whether serial port B is enabled or disabled (display only).
Selects the base I/O address for serial port B.
Selects the interrupt for a serial port B.
Selects whether the USB 2.0 device is enabled or disabled.
Page 82
4-18 Configuring Your Server
Option Parameter Description Your Setting
Parallel ATA Disabled
[Enabled]
Serial ATA Disabled
[Enabled]
SATA Controller Mode Option
SATA AHCI [Disabled]
SATA RAID [Disabled]
[Compatible] Enhanced
Enabled
Enabled
Selects whether the parallel ATA is enabled or disabled.
Selects whether the serial ATA is enabled or disabled.
This menu is available only when "Serial ATA" is enabled. Selects the SATA Controller Mode Option on mother board. "Compatible": Automatically detects SATA hard disk drive and controls it as the normal hard disk drive. "Enhanced": Automatically detects SATA hard disk drive and controls it in native IDE mode.
This option is available only when "Enhanced" is set for "SATA Controller Mode Option". Selects whether the SATA AHCI is enabled or disabled.
This option is available only when "Enhanced" is set for "SATA Controller Mode Option". Selects whether the RAID disk drives that uses the onboard SATA is enabled or disabled. Note: If you attempt to start the system from SATA hard disk drive with different setting, the data may be destroyed.
[ ]: Factory-set
Page 83
Configuring Your Server 4-19
Advanced Chipset Control
The following screen appears if you select "Advanced Chipset Control" on the Advanced menu. Selecting an item on the screen allows the proper submenu to appear.
See the table below for the items.
Option Parameter Description Your Setting
Multimedia Timer
Intel(R) I/O AT [Disabled]
Wake On LAN/PME
Wake On Ring [Disabled]
Wake On RTC Alarm
[Disabled] Enabled
Enabled
Disabled [Enabled]
Enabled
[Disabled] Enabled
Specify whether the timer corresponding to multimedia is enabled or disabled.
Specify whether the Intel(R) I/O Acceleration Technology feature is enabled or disabled.
Specify whether the remote power-on function through a network is enabled or disabled.
Specify whether the remote power-on function through a serial port is enabled or disabled.
Specify whether the scheduling power-on function by using RTC alarm feature is enabled or disabled.
[ ]: Factory-set
IMPORTANT: If supplying AC power to the server is stopped, the
remote power-on function (Wake On LAN/PME and Wake On Ring) is disabled at the next boot. Press the POWER switch to restart the system. The Wake On LAN/PME and Wake On Ring functions are enabled when the DC power is supplied to the server at the next time.
Page 84
4-20 Configuring Your Server
Security
The Security menu appears if you move the cursor to the position of "Security."
Press Enter on "Set Supervisor Password" or "Set User Password" to display the dialog to set/change password.
IMPORTANT:
User password can be set only when Supervisor password is already
set.
Set the passwords only after OS is installed.
If you forget the passwords, contact your service representative.
Page 85
Configuring Your Server 4-21
See the table below for the items.
Option Parameter Description Your Setting
Supervisor Password Is
User Password Is Clear
Set Supervisor Password
Set User Password
Password on boot* [Disabled]
Fixed disk boot sector
Power Switch Inhibit
* You can set this item on [Set Supervisor Password] menu.
Clear Set
Set Up to eight
alphanumerics
Up to eight alphanumerics
Enabled
[Normal] Write Protect
[Disabled] Enabled
Indicates the password setting status.
Indicates the password setting status.
Press Enter to display the supervisor password entry screen. This password enables all the SETUP menus to be accessed. This setting can be done only on login with the password input of "Supervisor" at start of SETUP.
Press Enter to display the user password input screen. For this password, accessing to the SETUP menu is restricted.
Specify whether the passwords are entered or not on booting. At first the supervisor password must be set. If the supervisor password is set and this option is disabled, BIOS determines that a user is booting.
Specify whether to permit writing into boot sector of the hard disk drive or not.
Specify whether to enable or disable the power switch feature.
[ ]: Factory-set
Page 86
4-22 Configuring Your Server
Server
The Server menu appears if you move the cursor to "Server."
If you select a menu item preceded by symbol
See the table below for the items.
³ and press Enter, the appropriate submenu appears.
Option Parameter Description Your Setting
System Management Console Redirection Event Log Configuration Assert NMI on SERR Assert NMI on PERR FRB-2 Policy Disable FRB2 Timer
Displays submenu.
Displays submenu.
Displays submenu.
Disabled
[Enabled]
Disabled
[Enabled]
Disable BSP
Do Not Disable BSP
[Retry 3 Times]
Indicates whether PCI SERR is supported or not. Indicates whether PCI PERR is supported or not. Set the FRB level 2 timer.
Page 87
Configuring Your Server 4-23
Option Parameter Description Your Setting
Boot Monitoring [Disabled]
Every 5 minutes between 5 minutes and 60 minutes
Boot Monitoring Policy
Thermal Sensor Disabled
BMC IRQ Disabled
[Retry 3 Times] Retry Service Boot Always Reset
[Enabled]
[IRQ 11]
Specify whether to enable or disable the boot monitoring function on booting, or select the time limit for timeout. To use this function, install NEC ESMPRO Agent. Set this item to "Disabled" if the system is booted from OS without installation of NEC ESMPRO Agent.
Specify the processing at the occurrence of timeout during boot monitoring. If [Retry 3 times] is selected, the system is reset after the occurrence of timeout and OS boot is retried up to three times. If [Retry Service Boot] is selected, the system is reset after the occurrence of timeout and OS boot is retried up to three times. Then the boot is tried from the service partition for three times. The failure in the third boot causes the system to stop booting. If [Always Reset] is selected, the system is reset after the occurrence of timeout and OS boot is retried repeatedly. * If no service partition exists in
the system, OS boot is retried repeatedly from the system
partition. Specify whether to enable or disable the thermal sensor monitoring function. If a thermal error is detected with this item being set to "Enabled", the system stops at the end of POST. Set the IRQ for BMC.
Post Error Pause Disabled
[Enabled]
AC-LINK Stay Off
[Last State] Power On
Indicates whether POST is aborted once at the end of POST if an error occurs during the execution of POST. Specify the state of power when the AC power to the server is turned off once and then on. (See the table below.)
Page 88
4-24 Configuring Your Server
Option Parameter Description Your Setting
Power on Delay Time
Platform Event Filtering
[0] - 255 Specify the DC power on delay
time within the range between 0 and 255 seconds. The time specified is valid when "Power On" or "Last State" is specified for AC
LINK. Disabled [Enabled]
This item becomes meaningless
when the notification feature of
EXPRESSSCOPE Engine is
enabled.
[ ]: Factory-set
The table below shows the operation when the AC power to the server is turn off once and then on again, depending on the setting of "AC LINK."
System status before AC power off
Operating Off On On Aborting (DC power being off also) Off Off On Forced shutdown Off Off On
* Press the power switch continuously for four seconds or longer. This forcibly turns off the power.
Setting of AC LINK Stay Off Last State Power On
IMPORTANT:
To power on the server from the UPS (Uninterruptible Power
Supply), select [Server] - [AC Link] - [Power On].
If the server is connected to the UPS, set at least 10 seconds delay in
the power-on schedule.
Page 89
Configuring Your Server 4-25
System Management
The following screen appears if you select "System Management" on the Server menu and press Enter.
See the table below for the items.
Option Parameter Description Your Setting
BIOS Version Displays the current BIOS version. (View only) Board Part Number Board Serial Number System Part Number System Serial Number Chassis Part Number Chassis Serial Number Onboard LAN1 MAC Address Onboard LAN2 MAC Address Management LAN MAC Address BMC Device ID Displays the device ID of BMC (Baseboard
BMC Device Revision BMC Firmware Revision SDR Revision Displays the revision of SDR (Sensor Data
PIA Revision - Displays the revision of PIA (Platform
Displays the mother board part number. (View
only)
Displays the mother board serial number.
(View only)
Displays the system code number. (View only)
Displays the System serial number. (View only)
Displays the chassis part number. (View only)
Displays the chassis serial number. (View only)
Displays the MAC address of onboard network
controller 1. (View only)
Displays the MAC address of onboard network
controller 2. (View only)
Displays the MAC address of management
network controller 2. (View only)
Management Controller). (View only)
Displays the revision of BMC (Baseboard
Management Controller) device. (View only)
Displays the revision of BMC (Baseboard
Management Controller) firmware. (View only)
Record). (View only)
Information Area). (View only)
[ ]: Factory-set
Page 90
4-26 Configuring Your Server
Console Redirection
The following screen appears if you select "Console Redirection" on the Server menu and press Enter.
See the table below for the items.
Option Parameter Description Your Setting
BIOS Redirection Port
ACPI Redirection Port
Baud Rate 9600
Flow Control None
Terminal Type PC ANSI
Remote Console Reset
[Disabled] Serial Port A Serial Port B [Disabled] Serial Port A Serial Port B
[19.2k]
38.4k
57.6k
115.2k
XON/XOFF [CTS/RTS] CTS/RTS+CD
[VT100+] VT-UTF8 [Disabled] Enabled
Specify the serial port to which a remote console is connected.
Specify the serial port to which an ACPI console is connected.
Specify the baud rate used for the interface with successive remote consoles.
Specify the flow control method.
Specify the type of remote console.
Specify whether to enable or disable the reset command issued from remote console.
[ ]: Factory-set
Page 91
Configuring Your Server 4-27
Event Log Configuration
The following screen appears if you select "Event Log Configuration" on the Server menu and press Enter.
See the table below for the items.
Option Parameter Description Your Setting
Clear all Event Logs
Enter
Press Enter and select "Yes" on the confirmation screen to clear the system event log.
[ ]: Factory-set
Page 92
4-28 Configuring Your Server
Boot
If you move the cursor to the position of "Boot," the Boot menu appears, which is used to set the boot priority.
The server searches for devices in the order set in this menu on booting. Finding the boot software, the server starts the software.
The priority of the boot devices can be changed by using the , , +, and - keys. Move the cursor to the desired device with the or key and change the priority with the + or - key.
IMPORTANT: To boot NEC EXPRESSBUILDER, set the priority of
the devices as shown in the figure above.
Page 93
Exit
The Exit menu appears if you move the cursor to "Exit."
Configuring Your Server 4-29
The options on the menu are described below.
Exit Saving Changes
Select this item to terminate SETUP after saving the newly selected information in CMOS (nonvolatile memory). Selecting "Exit Saving Changes" causes the confirmation screen to appear. If you select "Yes," SETUP is terminated with the newly selected information saved in CMOS (nonvolatile memory). Then the server automatically reboots the system.
Exit Discarding Changes
Select this item to terminate SETUP without saving the newly selected information in CMOS (nonvolatile memory). When the confirmation message "Save before exiting?" appears, select "No" to terminate SETUP without storage of the modified information. Then the server proceeds to Boot menu. Selecting "Yes" allows SETUP to be terminated with storage of the modified information. Then the server automatically reboots the system.
Load Setup Defaults
Select this item to return all the values of SETUP to the default values. Selecting "Load Setup Defaults" causes the confirmation screen to appear. Select "Yes" to return the values to the default values. Select "No" to return to the Exit menu screen.
Page 94
4-30 Configuring Your Server
IMPORTANT: This option sets [SATA RAID Enabled] in the
[Advanced] - [Peripheral Configuration] menu to [Disabled]. If the SATA hard disk drives are installed in your server and the onboard SATA RAID feature is used, change the parameter of the [SATA RAID Enabled] from [Disabled] to [Enabled] before exiting BIOS Setup. Leaving this parameter as the factory-set value (Disabled) may destroy the data in hard disk drive.
NOTE: To display the [SATA RAID Enabled] menu, select
[Advanced] - [Peripheral Configuration] - [SATA Controller Mode Option] - [Enhanced].
Load Custom Defaults
Select this item and press Enter to load the custom defaults stored. This menu does not appear if the Custom Defaults are not saved.
Save Custom Defaults
Select this item and press Enter to save the parameters currently being edited as custom defaults. When the parameters are saved, the Load Custom Defaults menu appears.
Discard Changes
Select this item to return the values modified currently to the previous values before saving the values to CMOS.
Save Changes
Select this item to save the newly selected information to CMOS (non-volatile memory) without the termination of SETUP.
Page 95
Configuring Your Server 4-31

SETUP UTILITY

This section describes the RAID configuration tool, LSI Logic Software RAID Setup Utility. This utility resides on the LSI Logic Software RAID, therefore, its operation is independent from the operating system.
NOTE: The LSI Logic Software RAID Setup Utility cannot be
operated through the remote console feature of NEC DianaScope.

Running Setup Utility

Running LSI Logic Software RAID Setup Utility
When the following screen appears after you have powered on the server, press Esc.
1.
The POST screen appears.
2. Check the description as shown below on the POST screen, then press Ctrl + M or Enter.
LSI Logic Software RAID Setup Utility starts.
LSI Logic SoftwareRAID BIOS Version xxxxxx LSI Logic MPT RAID Found at PCI Bus No:xx Dev No:xx Scanning for port 00 Responding xxxxxxxx xxxxMB Standard FW xxx DRAM=128MB(SDRAM) xx Logical drive(s) Configured Press <Ctrl><M> to Run LSI Logic Software RAID Setup Utility
NOTE: Press Ctrl + M to start the LSI Logic Software RAID Setup
Utility.
Page 96
4-32 Configuring Your Server
LSI Logic Software RAID Configuration Utility TOP Menu (Management Menu)
Exiting from LSI Logic Software RAID Setup Utility
Press Esc in the TOP menu of LSI Logic Software RAID Setup Utility.
When a confirmation message appears, select [Yes].
When the above message appears, press Ctrl + Alt + Delete.
The server is rebooted.
Page 97
Configuring Your Server 4-33
)

Menu Tree

Setting list
+: Selection/execution parameter : Setting parameter. : Information display >: Can be set (modified) after creation of logical drive
Menu Description
+Configure Performs Configuration settings
+Easy Configuration Set configuration (Using fixed value) +New Configuration Set new configuration +View/Add Configuration Additional setting / viewing configuration +Clear Configuration Clear configuration
+Select Boot Drive Chose Bootable Logical Drive +Initialize Initialize logical drive +Objects Various settings
+Adapter Set disk array controller
+Sel. Adapter Clear configuration
Rebuild Rate 30Chk Const Rate 30FGI Rate 30BGI Rate 30Disk WC Display default value (setting not required)Read Ahead OnBios State EnableStop on Error NoFast Init EnableAuto Rebuild OnAuto Resume EnableDisk Coercion 1GBFactory Default Default setting
+Logical Drive Logical drive operation
+Logical Drives Select logical drive(when multiple logical drives exist
+Initialize Initialize logical drive +Check Consistency Check logical drive redundancy +View/Update Parameters Display logical drive information
RAID Display RAID level
SIZE Display logical drive capacity
Stripe SIZE Display stripe size
#Stripes Display the number of hard disk drives in logical drive
State Display logical drive status
Spans Display setting of span
Disk WC Display setting of write cache
Read Ahead Display setting of read ahead
+Physical Drive Physical drive operation
+Physical Drive Selection Menu Select physical drive
+Make HotSpare Set as hot-spare disk for auto rebuilding +Force Online Make a disk online +Force Offline Make a disk offline +Drive Properties Display hard disk drive information
Device Type Hard disk drive type
Capacity Hard disk drive capacity
Product ID Hard disk drive model
+Rebuild Perform rebuilding +Check Consistency Perform logical drive redundancy check
Revision No. Hard disk drive revision
Page 98
4-34 Configuring Your Server

Operating Procedures for Setup Utility

Creating/Adding Configuration
Run LSI Logic Software RAID Setup Utility
Set new configuration information (pack/logical drive settings)
Check the logical drive settings
Initialize logical drive
Perform Consistency Check
Exit LSI Logic Software RAID Setup Utility
1. Run LSI Logic Software RAID Setup Utility.
2. Select "Configure" "New Configuration" from the TOP menu (Management Menu).
Select "View/add Configuration" to add configuration.
IMPORTANT:
Creating a configuration using "New Configuration" menu clears
the existing configuration information. To add configuration information to the existing configuration, select "View/add Configuration."
You cannot create Spanning of RAID1 or set the logical drive
capacity on "Easy Configuration" menu. Use "New Configuration" or "View/Add Configuration" instead.
Page 99
Configuring Your Server 4-35
3. When a confirmation message (Proceed?) is displayed, select "Yes."
The SCAN DEVICE starts (scanning information is displayed at the bottom of the screen). Upon completion of SCAN DEVICE, the "New Configuration - ARRAY SELECTION MENU" screen appears.
4. Move the cursor onto the hard disk drive to be packed by using cursor key and then press
Space to select the hard disk drive.
The display for the selected hard disk drive changes from READY to ONLINE.
5. Press F10 to set "Select Configurable Array(s)".
6. Press Space.
SPAN-1 is set.
Page 100
4-36 Configuring Your Server
7. Press F10 to create logical drive.
The "Logical Drives Configure" screen appears. (The figure below shows an example of RAID1 configured with two hard disk drives.)
Logical Drives Configured
LD0RAID1Size
xxxMB
Logical Drive0
RAID = 1 Size = xxxxMB DWC = On RA = On Accept Span = NO
#Stripes2Stripe Sz
64KB
Status ONLINE
8. Select "RAID," "Size", "DWC", "RA", or "Span" by using cursor keys. Then press Enter
to fix the selection and set each value.
(1) "RAID": Sets RAID level.
Parameter Remarks
0RAID0 1RAID1 10 Spanning of RAID1
The selectable RAID level varies depending on the number of hard disk drives that configure a pack.
(2) "Size": Sets logical drive size.
Up to 40 logical drives can be created per disk array controller.
(3) "DWC": Sets parameter for Disk Write Cache.
Parameter Remarks Off Write through On Write back
(4) "RA": Sets parameter for Read Ahead.
Parameter Remarks Off Does not perform read ahead. On Performs read ahead.
Loading...