Navman M300 User Manual

NAVMAN

�

RCL

AVG

MAX

8 7

M300 — Settings

NAVMAN NAVMAN NAVMAN

M300 — Settings M300 — Modes M300 — Modes

Press and hold

repeatedly to step through the setting options.

Press

Press both buttons together (

to enter setup

) to start or stop editing

a setting option.

repeatedly to step through selectable states,

While editing, press

or increase/decrease values. Press and hold the appropriate button increase/decrease values quickly

Set (12hr)

lets you set 12hr or 24hr time format

Set (31-12)

lets you set dd-mm or mm-dd date format

Beep

When beep is «ON» a beep will sound when the buttons are pushed.

Set units (knots)

lets you set speed units to «knots», «km/h» or «mph»

Distance is displayed in units corresponding to the speed units, i.e. if you choose «knots» for speed units, then distance is displayed in nautical miles.

Set offset

lets you adjust the M300 to display local time

The date is displayed to ensure that time adjustments are made in the correct direction, i.e. both correct time and correct date should be displayed. GPS signals must be obtained to set local time.

Press and hold

to leave setup

settings editing details

set (12hr) set (12hr)

beep

set units (knots)

set offset

edit

set (31-12)set (31-12)

beep

set units (knots)

time (date)

set 12hr

set 24hr

set 31-12

set 12-31

beep ON

beep OFF

set units (knots)

set units (km/h)

set units (mph)

Normal operating modesUse the settingsSetting options

Press

cycle automatically through modes).

Speed

shows session distance and current speed

Speed (AVG)

shows session distance and average speed

Speed (MAX)

shows session distance and maximum speed

Odometer mode

shows total distance from last odometer reset

Heading mode

shows current heading in degrees from true North

Clock

shows the current time and date

(You may need to adjust the settings to display your local time.)

Timer

shows session and lap times

The timer starts automatically whenever you start moving and stops whenever you stop moving.

Timer Recall

lets you recall stored lap data. Repeatedly pressing

lap data starting from the last stored lap, then lap 1, 2, 3 etc.

Press and hold

to start normal operation

repeatedly to step through the modes (hold

to shut down the M300

recalls

Use the modes

modes

Speed

Speed (AVG)

Speed (MAX)

Odometer

Heading

Clock

Timer

Timer recall

operating details

store current lap data clear all session data*

store current lap data

clear max speed only

store current lap data

clear odometer only

store current lap data

store current lap data clear all session data*

recall lap data restart recall from lap 1

(*does not clear odometer)

QUICK START GUIDE

KEY KEY = press this button = press this button = press both buttons together

= press this button

= press both buttons together

= press and hold both buttons together

Step 1

nmi knots

RCL

AVG

MAX

8 7

Step 2

Step 3

NOW YOU KNOW.

Get ready

Fit the battery

For best performance:

General use =

Below 5

1. Turn D-ring anti-clockwise and slide enclosure cover down to open battery enclosure.

2. Insert battery with «» end as indicated inside enclosure.

3. Replace enclosure cover (ensuring lugs at the bottom of the cover are aligned with slots in the enclosure surround), turn D-ring clockwise to seal.

C = NiMH

Alkaline

Fit the M300

The M300 is designed to be worn on the left upper arm. You may wish to adjust some of the settings prior to ﬁtting.

Be outdoors

The M300 is not intended for operation indoors or under water as it uses Global Positioning System (GPS) satellites to get time and date information, and to calculate distance and speed. For best results, always use the M300 outdoors with an unobstructed view of the sky.

Get set

Know the buttons

(as shown above) are pressed

The control buttons,

separately or together to turn the unit «ON» and «OFF», cycle through modes, and select mode options.

Know the startup options

1. enter setup

2. start normal operation

Always enter setup ﬁrst if you wish to change settings. To enter setup after starting normal operation, you must shut down and re-start the M300.

Flashing icon = seeking GPS signals Constant icon = GPS signals obtained

Startup could take up to 80 seconds to get all satellite data.

Enter setup

Press and hold

If you release

will immediately start normal operation.

For details about system settings see over page or consult User Guide.

Press and hold

and

to enter setup

counter

before the counter reaches zero, the M300

to leave setup

counter

Start normal operation

to start normal operation

Press

When starting directly into normal operation M300 will start in the mode it was in at last shutdown.

The M300 automatically operates whenever you are moving and pauses operation while you are stationary. Modes are accessed in the following order:

For details about modes, see over page or consult User Guide.

Mode example (speed)

Mode icons appear in the lower section of the screen. While in Speed mode you can monitor session distance and current speed. You can also store laps or clear session data.

While in Speed mode

Press

Press and hold

odometer) Press

Speed

Speed AVG

Timer RCL

session distance

speed mode icon

to store lap data

to clear all* session data (*does not clear

to go to next mode

Speed MAX Odometer

HeadingClockTimer

current speed

When you want to shut down the M300

After leaving setup, the M300 automatically starts normal operation displaying the speed mode ﬁrst.

Press and hold

Now you know.

Navman M300 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual