Navman iCN 510, iCN 520 User Manual

iCN 500 series

with Smart

2005

User Manual

iCN 510 iCN 520

English - Europe / Australia / New Zealand

iCN 500 series | User Manual

Contents

Box Contents ............................................................................ 5

1. Introduction ...........................................................................

2. iCN Features ........................................................................

3. Positioning the iCN in a Vehicle ........................................... 12

4. Starting Your iCN ................................................................ 14

5. Memory Card

. ..................................................................... 18

6. Changing Language ............................................................ 18

7. GPS Status ......................................................................... 20

8. Setting your Destination ...................................................... 21

By Address - Europe and New Zealand .......................... 24

By Address - Australia, Canada and USA ........................ 28

By POI - Europe and New Zealand .................................. 32

By POI - Australia, Canada and USA ............................... 35

9. Using the 2D Map Screen to Plan a Route ......................... 38

10. Multi-stop Trips .................................................................... 39

Europe and New Zealand ................................................ 39

Australia, Canada and USA ............................................. 44

11. Viewing Your Route ............................................................. 50

12. The 2D Map Screen Pop-up Menu ..................................... 55

13. Avoiding an Area ................................................................. 56

14. Route Demonstrator ............................................................ 57

15. Favourites and My Home .................................................... 59

16. Preferences ......................................................................... 64

17. Smart

 Desktop ................................................................ 78

18. Updating your iCN .............................................................. 80

19. Installing Maps Using Smart Desktop ............................. 81

20. Installing a Language on Your iCN 510 ............................... 84

21. Continuous Continental Navigation ..................................... 86

22. Smart Desktop Advanced Features ................................ 88

23. Accessories ........................................................................ 93

Appendix: Street Types ............................................................. 94

Support Information .................................................................. 97

Compliance ............................................................................... 97

iCN 500 series | User Manual

Getting started

Thank you for purchasing this Navman iCN. We hope you enjoy your new GPS transferable navigation system. This user manual will help you Drive-Away™ with your iCN, straight out of the box. Navman welcomes your feedback. To contact us or visit our website, see Support Information on page 97.

Box Contents

Purchasers of Smart 2005 software-only upgrade kits, see the enclosed Upgrade Guide for your Box Contents.

Mounting brackets

Socket-clip

Locking-nut

Suction-cup/ ballfoot

iCN with GPS Antenna

12 V In-Vehicle Power-Adaptor with Power-Cable

USB Cable

Protective Carry-Case

CD-ROMs, including:

• Smart™ 2005 software including Smart Desktop

• Map data

• User Manual (PDF format) and Adobe

Reader®

Note: The number of disks varies with country of purchase

AC Power-Pack with Power-Cable

Note: The number of plugs depends on the country of purchase

Memory Card

(may not be included)

Documentation, including:

• User Manual

• In-Car Installation Guide

• Software Product Licence/ Limited Warranty Agreement

• Registration Card

Remote Control

(iCN 510, 520 Premium only)

iCN 500 series | User Manual

Getting started

iCN 500 series | User Manual

Getting started

1. Introduction

Whether you travel in your own country or elsewhere, the iCN will direct you to your destination without the need for map-books and second-hand instructions.

The Global Positioning System (GPS) is available free of charge, at any time, and is accurate to within 5 m (15 ft). Your iCN map provides street-level detail for door-to-door navigation, including Points of Interest (POIs) such as accommodation, petrol stations, railway stations and airports.

Use this manual to learn how to operate your iCN efﬁciently and safely, and discover all the different features available to you.

GPS and GPS Signals

The Global Positioning System is a network of satellites that transmit accurate time and position information worldwide. GPS receivers receive signals from these satellites and use the information to determine an exact location. Satellites orbit the earth at around 12,000 miles. While a GPS receiver can detect signals from up to 12 satellites at any time, only three signals are needed to provide a position or “GPS ﬁx” (latitude and longitude) for vehicle navigation systems.

The iCN GPS antenna receives GPS signals. To receive GPS signals, ensure that the iCN is outdoors, or in a vehicle outdoors, and the GPS antenna has an unobstructed view of the sky. The iCN can operate in all weather types except snowfall.

For details about GPS and your iCN, see page 20.

Safety Notice

WARNING: In a vehicle, it is your sole responsibility to place, secure and use the iCN in a manner

that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing safe driving practices. It is your responsibility to read and follow the vehicle mount installation instructions and to use the product consistent with your government’s laws/regulations. Consult the vehicle manual to ensure the mounting location is safe.

It is your sole responsibility to adhere to the following safety instructions at all times:

• Do not operate the iCN while driving or place the iCN in a position that obstructs the driver’s view.

• Do not mount the iCN in a way that may be distracting or interfere with the safe operation of the vehicle, the deployment of airbags or other safety equipment.

• Do not leave the iCN in view while your vehicle is unattended, especially in strong or direct sunlight.

• Do not use or handle the iCN when it is hot; leave it to cool, out of direct sunlight.

Failure to adhere to these instructions may lead to serious personal injury, including death, or property damage. Navman disclaims all liability for use of the iCN that contributes to injuries, death, property damage or violates law.









  

  

iCN 500 series | User Manual

Getting started

2. iCN Features

We recommend that you familiarize yourself with the iCN’s basic operations, such as using the stylus, 4-way toggle and Volume control.

Front Components

Component Description



Charge Indicator

Amber indicates that battery is charging;

Green indicates that battery is fully charged.



Touch Screen

Displays maps and menu options. Tap with the stylus to select menu options or enter information.



Displays the Main Menu screen. Press and hold to reset the iCN.



Power

Turns the iCN on or off. When off, the iCN enters a suspended state.



ESC

Cancels an action, returns to the previous screen and deletes the last text character on the Keyboard screen; hold down for longer to delete a whole line at once.



Page

Cycles through the 2D Map, 3D Map, Next Turn and Next 4 Turns screens; displays additional preferences or search-result screens, when available.



Displays a smaller area in greater detail on the Map and 3D Map screens, or press and hold to increase the screen brightness.



Displays a larger area in less detail on the Map and 3D Map screens, or press and hold to decrease the screen brightness.







iCN 500 series | User Manual

Getting started

Component Description



4-Way Toggle

Selects Main Menu options, keyboard characters and Preferences, moves around the 2D Map screen to select a destination, and scrolls through lists, such as lists of search results; press centre to conﬁrm the selected menu option, text or preference; press up or down to adjust the viewing angle on the 3D Map screen.



Speaker

Outputs voice commands and warnings. Use the Volume control to adjust.

Back Components

Component Description



Battery Switch

Must be set to ON for normal use. Switching to OFF will turn the battery off, saving battery power.



GPS Receiver

Receives signals from GPS satellites when lifted out to the horizontal position.



External Antenna Socket

Connection socket for GPS mMCX External Antenna (not included). Protected by rubber cover.















iCN 500 series | User Manual

Getting started

Side Components

Component Description



SD/MMC Slot

Slot for memory card. Memory card must be inserted with label facing forward.



Stylus

Used to tap the screen to make selections and enter information; Pull out of the slot to use and insert in the slot to store.



Volume Control

Rotate up or down to hear a sound test; rotate and hold to adjust volume.



Headphone Socket Connection socket for headphones or earphones (not included).

End Components

Component Description



Reset Resets the iCN; press using the stylus.



USB Socket Connection socket for USB cable to your computer.



Power Socket

Connection socket for vehicle power-adaptor or AC power-pack cable.

iCN 500 series | User Manual

Getting started

Stylus

The stylus is your input device. Pull the stylus out of the slot and extend it for ease of use. Store it in the slot when not in use.

• Tap the screen with the stylus to select.

• Tap and drag the screen with the stylus to navigate the Map and 3D Map screens.

Internal Battery

The iCN has an internal battery that when fully charged should power the iCN for 4 hours. You can monitor battery power at the Power Status screen:

Main Menu  Preferences  More Preferences  Hardware  Power Status

Charging the Battery

When the battery is charging, the Charge Indicator is amber; when the battery is fully charged, the Charge Indicator is

green.

• To charge the iCN in a vehicle, plug the vehicle power-adaptor into the Power Socket on the bottom of the iCN and the other end into the vehicle power-socket.

• To charge the iCN using an electrical wall outlet, plug the AC power-pack into the Power Socket on the bottom of the iCN and the other end into the wall outlet.

Click

iCN 500 series | User Manual

Getting started

3. Positioning the iCN in a Vehicle

Before you begin, check if your vehicle is ﬁtted with a heat-reﬂective or heated windscreen. If so, you will need to purchase an external antenna for your iCN to receive GPS signals. See page 93.

Follow the safety notice on page 7 to ensure that the iCN does not obstruct the driver’s view, or interfere with the operation of vehicle airbags and safety devices.

Assembling the iCN Suction-Mount

Choose a position on the windshield that is clearly visible to the driver without obstructing the view of the road.

1. Assemble the suction-mount:

• Slip the locking-nut over the ballfoot.

• Snap the socket-clip onto the ballfoot.

• Screw the locking-nut onto the thread of the socket-clip until ﬁrm.

2. Check the Battery Switch on the back of the iCN. If it is switched to OFF, then remove the stylus and use it to switch the Battery Switch to ON

3. Open the GPS antenna outwards, so that it has a clear view of the sky.

4. Gently insert the memory card in the Memory Card slot with the label facing the front of the iCN. See page 18 for how to insert the memory card.

a b

Click

iCN 500 series | User Manual

Getting started

5. Insert the iCN into the suction-mount:

a. Position the two locating-tabs on the underside of the iCN into the corresponding slots

on the socket-clip.

b. Snap the upper side of the iCN into the socket-clip.

6. Use the alcohol swab to clean and dry the suction-cup and the mounting-area on the windshield, then attach the suction-mount to the windshield:

a. Hold the suction-cup ﬁrmly against the windshield and b. Press the lever towards the suction-cup.

7. Connect the iCN to the vehicle power supply:

a. Plug the small end of the In-Vehicle Power-Adaptor into the Power Socket on the left side

of the iCN.

b. Plug the other end of the In-Vehicle Power-Adaptor into the 12 V vehicle power-socket.

8. Press

The iCN will turn on.

iCN 500 series | User Manual

Getting started

4. Starting Your iCN

The Main Menu screen provides access to all of the iCN’s functions, including navigating to a destination.

Step One: Turn iCN On

1. Check the Battery Switch on the back of the iCN. If it is switched to OFF, then remove the stylus and use it to switch the Battery Switch to ON

2. Gently pull the bottom of the GPS receiver away from the iCN. The receiver will lift out to a horizontal position to allow it to obtain a GPS ﬁx.

3. Press

The iCN will turn on.

iCN 500 series | User Manual

Getting started

Step Two: Language Screen

iCN 510: If you purchased your iCN 510 in Australia, Canada, United Kingdom or United States,

then English is chosen by default and the Warning screen will display instead of the Language screen. Go to Step Three: Warning Screen. To change the language from English to another, see Installing a Language on Your iCN 510

page 84.

iCN 520:

If you purchased your iCN 520 in Australia, Canada, New Zealand, or United States, then English is chosen by default and the Warning screen will display instead of the Language screen. Go to Step Three: Warning Screen.

European Users:

1. Tap your language choice.

Note: Ensure that the memory card supplied with your iCN is inserted in the SD/MMC slo

t (see page 14). If you are using a different memory card or files on your original memory card have been deleted, you may need to install a language on your iCN internal memory. See Changing Language on pages 18-19.

• To prevent the Language screen from displaying on each startup, select the Do not show on startup check box. iCN 520: Selecting the Do not show on startup check box will install the selected language

to your iCN internal memory. See page 19 for more information.

2. Tap

to go to the next screen.

The Warning screen will display.

Step Three: Warning Screen

1. Read the warning message.

2. Tap Accept to conﬁrm that you understand. The ﬁrst

Tutorial screen will display.

Step Four: Tutorial Screens

1. Read the Tutorial screen.

• To prevent the Tutorial from displaying on startup, select the Do not show Tutorial on startup check box.

2. Tap

to move through each Tutorial screen.

The Main Menu screen will display.

iCN 500 series | User Manual

Getting started

Main Menu Screen

• Use the stylus to select a Main Menu option.

• Return to the Main Menu screen at any time by pressing

• The Route Informatio

n option is only available when a route has been calculated.

See page 53-5

4 for more information.

ToTurn iCN Off

When your iCN is off, it enters a suspended state and the system stops operating. When you turn your iCN on, it returns to the screen you were last viewing.

1. Remove the iCN from the suction-mount bracket if necessary, then gently push the GPS receiver back towards the iCN. The receiver will click into place.

2. Press

The iCN will enter a suspended state and the screen will turn off.

Power-Saving Suspended State

To save battery power, your iCN will automatically enter a suspended state after a set period of time. You can change the default suspended-state settings at the Power Options screen.

Main Menu

 Preferences  More Preferences  Hardware  Power Options

Note: If you are not going to be using the iCN for a period of time,

switch the Battery Switch

to OFF to save battery power.

iCN 500 series | User Manual

Getting started

Reset iCN

Normally you do not need to reset your iCN; however, should your iCN not turn on or not respond, you can reset it to solve the problem.

To reset your iCN, either:

a. Press and hold

The message Reset Device? will display. Tap Yes.

b. Use the stylus to press the Reset button on the top of the iCN.

iCN 500 series | User Manual

Getting started

5. Memory Card

Your iCN came with a memory card containing a preactivated map of the region in which it was purchased. To navigate to your destination you will ﬁrst need to insert the memory card in your iCN.

Important: If any of the ﬁles on the memory card are deleted, or if you are using a different memory card from the one that came with your iCN, you may need to install a language to the iCN internal memory and install maps to your memory card. To install a language, see Changing Language below; for installing

maps using Smart Desktop on your computer,

see Installing

Smart Desktop on Your Computer on

page 7

8 and Installing Maps Using Smart Desktop on page 81.

Inserting Memory Card

Gently insert the card in the SD/MMC slot with the label facing the front of the iCN.

Removing Memory Card

Gently push down on the top edge of the card to release it, and pull it out of the slot.

6. Changing Language

iCN 510

The memory card that came with your iCN 510 contains a selection of languages. As long as this memory card is inserted in your iCN, you will be able to navigate using any of these languages by selecting one at the Language screen at startup, or at the Preferences - Language screen (see page 66).

The iCN 510 can store one language in internal memory, which is UK English by default. If you are using a different memory card to the one supplied with your iCN, you will only be able to navigate using this one language. To change the language stored in internal memory, complete Installing a Language on Your iCN 510 on page 84.

iCN 500 series | User Manual

Getting started

iCN 520

The memory card that came with your iCN 520 contains a selection of languages. As long as this memory card is inserted in your iCN (and you have not selected the Do not show on startup check box on the Language screen), you will be able to navigate using any of these languages by selecting one at the Language screen at startup.

The iCN 520 can store two languages in internal memory: UK English and one which you have installed using the below procedure. This means that if you are using a different memory card to the one supplied with your iCN, you can navigate using either UK English or your chosen language by selecting one at the Preferences - Language screen (see page 66).

Installing a Language to your iCN 520

To install a language on your iCN, the Language screen must be enabled to display at startup. If you have disabled the Language screen from displaying at startup, or you purchased your iCN 520 in Australia, Canada, New Zealand or United States, you must ensure the Language Selection Screen check box is selected on the Preferences - Startup screen. See page 77.

1. Turn on your iCN as per Step One of Starting Your iCN on page 14.

• If your iCN is already on, reset it as per the instructions on page 17.

2. When the Language screen is displayed, tap your language choice.

3. Select the Do not show on startup check box.

4. Tap

The selected language is installed to your iCN. The Warning screen will display.

5. Continue to Step Three of Starting Your iCN on page 15.

iCN 500 series | User Manual

Getting started

7. GPS Status

Signals are transmitted by Global Positioning System (GPS) satellites orbiting the Earth. You can view your GPS status at any time from the 2D Map, 3D Map, Next Turn and Next 4 Turns screens.

The GPS Strength Indicator

will display green when there is a valid ﬁx (2D or 3D), and between one and three bars will display to indicate the strength of the signal; the GPS Strength Indicator will display red when no ﬁx is available.

Tap the GPS Strength Indicator to open the Satellite Signal Strengths screen.

For more detailed information on your current GPS fix, see GPS Status

on page 73.

iCN 500 series | User Manual

Getting started

8. Setting Your Destination

For your safety, enter destination information before you start a journey.

Do not operate the iCN while driving

Select a destination using the Destination, Keyboard and Preview screens, which used together form a destination wizard.

This section describes how to use each of these screens and provides two case studies to help guide you through setting your destination.

Destination Screen

The Destination screen is used to select your destination by area, street, postal code/ZIP code, Point of Interest (POI), intersection, city, town, country or state.

As you specify each part of the address, it will display in the You are going to ﬁeld at the top of the screen. The available options will change to reﬂect the parts of the address still to be completed.

Keyboard Screen

The Keyboard screen will display when you are required to enter text, such as when searching for a street name. As you select each character, the ﬁrst two results will display. Tap

to see more search results. Search results will be listed in matching order, with the closest matches appearing at the top of the list.

The Keyboard screen can display in three modes: alphabet, alternate and number/symbol.

Figure 1. Alphabet Keyboard Figure 2. Alternate Keyboard

iCN 500 series | User Manual

Getting started

Figure 3. Number/Symbol Keyboard

As you select each character, the ﬁrst two results will display. Tap

to see more search results.

• To select a character or a search result, tap the character or search result.

• To delete a character, press ESC

or tap <<; hold ESC to delete the line.

• To display the number/symbol Keyboard screen (Figure 3), tap 123.

• To display the alternate Keyboard screen (Figure 2), press +, or tap Alt.

• To display the alphabet Keyboard screen (Figure 1), press

-, or tap ABC.

Preview Screen

The Preview screen is used to display a preview of your destination before navigating to it, saving it as a Favourite or displaying it on the 2D Map screen.

• To display a smaller area in greater detail, press

• To display a larger area in less detail, press -.

• To display your destination on the 2D Map screen, tap the preview map

The 2D Map screen will display.

• To save your destination as a Favourite, tap Save. The New Favourite screen will display. See Favourites and My Home on page 59.

• To calculate the route and open the 3D Map screen, tap Go. The 3D Map screen will display.

• To view Point of Interest (POI) details when your destination is a POI, tap

The POI Detail screen will display.

iCN 500 series | User Manual

Getting started

Address Search Rules

The following rules apply when searching for a destination in Europe:

Street Names with Dates

If a street name contains a date or a number, search by the ﬁrst number:

Example 1: If searching for “Faubourg du 13 Juillet 1920”, search by “13”. Example 2: If searching for “Avenue du 14 Avril 1914”, search by “14”. Example 3: If searching for “Rue de la 1 ere Arm

ée”, search by “1”.

Streets Named After People (excluding Italy)

If a street name is a person’s name (including at least a ﬁrst and last name), search by the ﬁrst name:

Example 1: If searching for “Rue Albert Mathieu”, search by “Albert”. Example 2: If searching for “Fred Archer Way”, search by “Fred”. Example 3: If searching for “Franz Grillparzer-Strasse”, search by “Franz”.

Street Named After People - Italy

In Italy, if a street name is a person’s name (including at least a ﬁrst and last name), search by the last name:

Example 1: If searching for “Via de Angelo de Thomasis”, search by “Thomasis”. Example 2: If searching for “Via Placido Giovanella”, search by “Giovanella”. Example 3: If searching for “Via della Giacomo Marca”, search by “Marca”.

Postcodes in United Kingdom and Netherlands

When searching by postcode in United Kingdom or Netherlands, type the postcode with spaces and without the last two letters.

Example 1: If searching for “RH6 9ST”, search by “RH6 9”. Example 2: If searching for “3514 BN”, search by “3514”.

For exact European street type abbreviations, see Appendix: Street Types on page 94.

iCN 500 series | User Manual

Getting started

Setting Your Destination by Address -

Case Study One: Europe and New Zealand

This case study will show you how to set your destination by selecting your country, then area, then street, then house number.

Note: This case study applies to Europe and New Zealand only. For navigating in Australia, Canada and USA, see page 28.

Step One: Open the Destination screen

a. From the Main Menu, tap Go To. b. From the Go To screen, tap Address or POI.

The Destination screen will display.

Important Note: If this is the first time you are setting your destination and you have maps from more than one country installed and selected, then the Select country

screen will

display instead of the Destination screen. Go directly to Step Two: Select the Country of

Destination, step b

The next time you perform this procedure, the Destination screen will open as expected.

Step Two: Select the Country of Destination

If you only have the map of one country installed and selected, that country is selected for your destination by default and cannot be changed. Go to Step Three: Find the Area of Destination

a. From the Destination screen, tap Change country.

The Select country screen will display.

b. Select a country from the list.

The Destination screen will display.

iCN 500 series | User Manual

Getting started

Step Three: Find the Area of Destination

a. From the Destination screen, tap Find area.

The Keyboard screen will display.

b. Use the Keyboard screen to ﬁnd the area of your destination.

For information on using the Keyboard screen, see pages 21-22

The Destination screen will display.

Step Four: Find the Street of Destination

a. From the Destination screen, tap Find street.

The Keyboard screen will display.

iCN 500 series | User Manual

Getting started

b. Use the Keyboard screen to ﬁnd the street of your destination. For information on using

the Keyboard screen, see pages 21-22. The Destination screen will display.

Step Five: Find the House Number of Destination

a. From the Destination screen, tap Enter house number.

The Keyboard screen will display.

Note: If the Enter house number option is not displayed, house numbers are not available for your selected street. Tap Go to centre of street to display the Preview screen. Go to step

iCN 500 series | User Manual

Getting started

b. Use the Keyboard screen to ﬁnd the house number of your destination. For information

on using the Keyboard screen, see pages 21-22

The Preview screen will display.

c. Complete one of the following:

• To calculate the route and open the 3D Map screen, tap Go

The 3D Map screen will display.

• To display the destination on the 2D Map screen, tap the preview map

The 2D Map screen will display.

• To save the destination as a Favourite, tap Save. The New Favourite screen will display. See Favourites and My Home on page 59.

• To change your destination, tap ESC. The Destination screen will display.

To return to the Main Menu, press

iCN 500 series | User Manual

Getting started

Setting Your Destination by Address -

Case Study Two: Australia, Canada and USA

This case study will show you how to set your destination by selecting your country, then state, then town or city, then street, then house number.

Note: This case study applies to Australia, Canada and USA only. For navigating in Europe and New Zealand, see page 24.

Step One: Open the Destination screen

a. From the Main Menu, tap Go To. b. From the Go To screen, tap Address or POI.

The Destination screen will display.

Important Note:

i. If this is the first time you are setting your destination and you have maps from more than

one country installed and selected, then the Select country

screen will display instead of

the Destination screen. Go directly to Step Two: Select the Country of Destination,

step b.

The next time you perform this procedure, the Destination screen will open as expected.

ii. If this is the first time you are setting your destination and you have maps from only one

country, but more than one state installed and selected, then the Select State

screen will

display instead of the Destination screen. Go directly to Step Three: Select the State

of Destination

The next time you perform this procedure, the Destination screen will open as expected.

Step Two: Select the Country of Destination

If you only have the map of one country installed and selected, that country is selected for your destination by default and cannot be changed. Go to Step Three: Select the State of

Destination

a. From the Destination screen, tap Change country or Change country or state.

The Select country screen will display.

b. Select a country from the list.

The Select state screen will display.

• If you only have the map of one state installed and selected, that state is selected for your destination by default. Go to Step Four: Find the Town or City of Destination

iCN 500 series | User Manual

Getting started

Step Three: Select the State of Destination

If you only have the map of one state installed and selected, that state is selected for your destination by default and cannot be changed. Go to Step Four: Find the Town or City of Destination.

a. Select a state from the list.

The Destination screen will display.

Step Four: Find the Town or City of Destination

a. From the Destination screen, tap Find town/city.

The Keyboard screen will display.

b. Use the Keyboard screen to ﬁnd the town or city of your destination. For information on

using the Keyboard screen, see pages 21-22

The Destination screen will display.

iCN 500 series | User Manual

Getting started

Step Five: Find the Street of Destination

a. From the Destination screen, tap Find street.

The Keyboard screen will display.

b. Use the Keyboard screen to ﬁnd the street of your destination. For information on using

the Keyboard screen, see pages 21-22. The Destination screen will display.

Step Six: Find the House Number of Destination

a. From the Destination screen, tap Enter house number.

The Keyboard screen will display.

Note: If the Enter house number option is not displayed, house numbers are not available for your selected street. Tap Go to centre of street to display the Preview screen. Go to step

+ 70 hidden pages