Navman 7000, 7100EU, 7100US User Manual

1.73 Mb
Loading...

VHF 7000, 7100US, 7100EU

Operation Manual

w w w . n a v m a n . c o m

NAVMAN

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

reorient or relocate the receiving antenna.

increase the separation between the equipment and receiver.

connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

consult the dealer or an experienced radio/TV technician for help.

IMPORTANT:

1.Some features described in this manual are not available on every model. In particular, DSC functions are NOT available on the 7000.

2.DSC functions will not operate on the 7100US or the 7100EU until your MMSID has been entered. Refer to section 4.2 for details.

3.The radio channels installed into the Navman VHF radio may vary from country to country, depending upon the model, and government or national communications authority regulations.

4.Navman NZ Ltd recommends that you check the radio operating licensing requirements of your country before using the Navman VHF radio. The operator is solely responsible for observing proper radio installation and usage practices.

5.A DSC warning label is supplied with the 7100US. To comply with FCC regulations, this label must be affixed in a location that is clearly visible from the operating controls of this radio. Make sure that the chosen location is clean and dry before applying this label.

It is the owner’s sole responsibility to install and use the instrument in such a manner that will not cause accidents, personal injury or property damage.

Navman NZ Limited disclaims all liability for any use of this product in a way that may cause accidents, damage or that may violate the law.

Governing Language: This statement, any instruction manuals, user guides and other information relating to the product (Documentation) may be translated to, or has been translated from, another language (Translation). In the event of any conflict between any Translation of Documentation, the English language version of the Documentation will be the official version of the Documentation.

This manual represents the Navman VHF 7000, 7100US, and &7100EU radios at the time of printing. Navman NZ Limited reserves the right to make changes to specifications without notice.

Copyright © Navman NZ Limited, New Zealand. All rights reserved. NAVMAN is a registered trademark of Navman NZ Limited.

2

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

Contents

 

Section 1 - General Information..............................................................

5

1-1 Features....................................................................................................

5

1-2 Customizing Your Navman VHF Radio.....................................................

6

1-3 How to Display and Navigate Menus........................................................

6

1-4 How to Enter Alphanumeric Data..............................................................

6

1-5 LCD Symbols and Meanings ...................................................................

6

1-6 Basic Operation and Key Functions..........................................................

8

Section 2 - The Radio Menu (MENU).....................................................

11

2-1 Radio Menu Options (Menu) ...................................................................

11

2-2 Maintain Your Buddy List (BUDDY LIST)................................................

12

2-2-1 Add an Entry......................................................................................

12

2-2-2 Edit an Entry......................................................................................

12

2-2-3 Delete an Entry..................................................................................

13

2-3 Local or Distance Sensitivity (LOCAL/DIST)...........................................

13

2-3-1 Set Distance Sensitivity.....................................................................

13

2-3-2 Set Local Sensitivity ..........................................................................

13

2-4 Backlighting (BACKLIGHT) and Contrast (CONTRAST)........................

13

2-4-1 Set the Backlighting Level.................................................................

14

2-4-2 Set the Contrast Level.......................................................................

14

2-5 GPS Data and Time (GPS/DATA)...........................................................

14

2-5-1 Manually Enter Position and UTC Time (MANUAL)..........................

14

2-5-2 Local Time (TIME OFFSET)..............................................................

14

2-5-3 Time Format Options (TIME FORMAT).............................................

15

2-5-4 Time Display Options (TIME DISPLAY) ............................................

15

2-5-5 Position Display Options (LL display)................................................

16

2-5-6 Course and Speed Display Options (COG/SOG)..............................

16

2-5-7 GPS Alert Options (ALERT) .............................................................

16

2-6 GPS Simulator (SIMULATOR) ................................................................

17

2-7 Reset to factory defaults (RESET)..........................................................

17

Section 3 - Radio Setup Menu (RADIO SETUP)...................................

18

3-1 Radio Setup Menu (RADIO SETUP) ......................................................

18

3-2 Channel Names (CH NAME) .................................................................

18

3-3 RING & BEEP Volume (RING VOLUME) & (BEEP VOLUME)..............

19

3-4 Internal Speaker connections (INT SPEAKER) ......................................

19

3-5 Set the Priority Channel (watch MODE) .................................................

19

3-6 Weather Alert (Wx ALERT) ....................................................................

20

3-7 NMEA protocol (COM PORT) .................................................................

20

Section 4 - DSC Setup Menu (DSC SETUP) .........................................

21

4-1 DSC Setup - Menu Options ....................................................................

21

4-2 Enter Your User MMSID (USER MMSID) ...............................................

21

4-3 Maintain Your Groups (GROUP SETUP)................................................

22

4-3-1 Create a Group (GROUP SETUP)....................................................

22

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

3

4-3-2 Edit Group Name Details ..................................................................

22

4-3-3 Delete a Group..................................................................................

23

4-4 Response to Individual Calls (INDIV REPLY) .........................................

23

4-5 atis MMSID & ATIS FUNCTIONALITY....................................................

23

4-5-1 Enter or Edit YOUR ATIS MMSID .....................................................

23

4-5-2 Enable ATIS Functionality (ATIS FUNC) ...........................................

24

4-6 DSC functionality options (DSC FUNC)..................................................

24

4-7 Response Type to LL POLLING Calls (LL REPLY).................................

25

Section 5 - Sending and Receiving DSC Calls ....................................

26

5-1 WHAT IS DSC?.......................................................................................

26

5-2 Sending dsc calls....................................................................................

26

5-2-1 Make a Routine Call (INDIvidual)......................................................

27

5-2-2 Retrying a Routine Call .....................................................................

27

5-2-3 Acknowledgement of an Individual Incoming Call (INDIV) ................

27

5-2-4 Recall the Most Recent Incoming Call (LAST)..................................

28

5-2-5 Call a Group (GROUP)......................................................................

28

5-2-7 Call using the Call Log (CALL LOG...................................................

29

5-2-8 Call using the Distress Log (DIST LOG) ...........................................

29

5-2-9 Request the LL Position of a Buddy (LL REQUEST) ........................

30

5-3 Receiving DSC Calls...............................................................................

30

5-3-1 Receiving an All Ships Call (ALL SHIPS)..........................................

31

5-3-2 Receiving an Individual Call (INDIV) .................................................

31

5-3-3 Receiving a Group Call (GROUP).....................................................

31

5-3-4 Receiving a Geographic Call (GEOGRAPH).....................................

31

5-3-5 Receiving a Polled Position Call (POSITION)...................................

32

Section 6 - Distress Calls ......................................................................

33

6-1 Sending a Distress Call ..........................................................................

33

6-2 Receiving a Distress Call (DISTRESS!)..................................................

34

6-3 Distress Acknowledgement (distress ack) or Relay ..............................

34

Appendix A - Technical Specifications...........................................................

35

Appendix B - Troubleshooting.......................................................................

38

Appendix C - VHF Marine Channel Charts...........................................

39

C-1 international Channel Chart....................................................................

39

C-2 USA Channel Chart................................................................................

42

C-3 CANADA Channel CHART.....................................................................

45

C-4 EU Channel Chart ..................................................................................

48

Special Channels 7.................................................................................

50

Appendix D - MMSID & License Information........................................

51

Appendix E - How to Contact Us...........................................................

52

4

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

Section 1 - General Information 1-1 Features

Congratulations on your purchase of a Navman VHF 7000, 7100US, or 7100EU marine band VHF radio. All of these models provide the following useful features:

prominent channel display

adjustable contrast settings for the LCD

adjustable keypad backlighting for easy night-time use

waterproof and submersible to comply with JIS-7

GPS latitude and longitude (LL) and time display (when connected to a GPS)

choice of High or Low (25 W or 1 W) transmission power

top centred PTT button for comfortable leftor right-handed use

powerful 4 W external audio output

access to all currently-available marine VHF channel banks (USA, Canada, International) including weather channels where available

special CH16 or CH16/9 key for quick access to the priority (international distress) channel

special 3CH key to select your three favourite channels

PSCAN (similar to dual watch) facility

In addition, the VHF 7100 models also provide:

DSC (Digital Select Calling) capability that meets USCG SC101 and Class D Standards. 7100US only.

DSC (Digital Select Calling) capability that meets EC Class D Standards.

VHF 7100EU only.

DISTRESS call button to automatically transmit the MMSID and position until an acknowledgement is received

easy access to a buddy list of up to 20 favourite people

MMSID storage for three favourite groups

Group Call and All Ships Call facility

LL position polling information

Weather alert facility. VHF 7100US only.

ATIS facility for inland waterways. VHF 7100EU only.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

5

1-2 Customizing your Navman VHF Radio

You can customize the radio to suit your individual preferences. Some preferences can be set directly through the keys as explained in this Section.

Other preferences are set up through the built-in menus and these are explained in the other Sections.

1-3 How to Display and Navigate Menus

1.Hold down MENU (or CALL/MENU). Note that only four menu items can be displayed at any one time on the screen.

2.Press + CH - to scroll up and down the menu until the cursor is positioned at the desired option. Press ENT to display that option.

3.Make any entries or changes as explained in the following section.

4.Press ENT to confirm changes. Otherwise, press ESC to keep the original entry.

5.Press ESC to backup one screen or exit. Any changes are active as soon as you exit the screen.

1-4 How to Enter Alphanumeric Data

If your radio does not have the optional alphanumeric microphone, use the + CH - key to enter alphanumeric data.

Press - to count through numbers, or hold down to scroll rapidly to the desired number. Press + to step through the alphabet, or hold down to scroll rapidly to the desired character.

If you make an error, press - until < is displayed, then press ENT to backup and correct the entry.

1-5 LCD Symbols and Meanings

This simulation shows the locations of all the following information symbols:

6

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

Symbol

Meaning

TX

Transmitting.

HI LO

Transmission power. High (HI) 25W or Low (LO) 1W.

WX

Weather channel.

WX ALT

Weather Alert. Alarm beeps will sound. VHF 7100US only.

BUSY

Receiver busy with an incoming signal.

PRI

Priority channel is selected.

DDuplex operation. Otherwise, blank for Simplex operation.

LOCAL

Local calling is selected. Otherwise, blank for distance calling.

DSC

DSC capability is available. VHF 7100US and VHF 7100EU only.

 

 

Incoming DSC call.

 

 

 

 

Low Battery warning (activates at 10.5 V)

 

 

 

 

 

88

 

Channel selected.

USA INT CAN

Selected channel bank for VHF radio operations and regulations.

XChannel is temporarily deleted from the ALL SCAN operation.

B A

Channel suffix, if applicable.

CH1 CH2 CH3

Shows which of the 3 favourite channels, if any, are selected.

 

Otherwise blank.

ATIS

Enabled for use in European inland waterways. Otherwise blank.

 

VHF 7100EU only.

A typical operational display is shown here.

The latitude and longitude of the vessel and the local time are shown.

A transmission on Channel 16 is being made at high power using the International channel bank.

Channel 16 is set as the Priority channel. It is also set as favourite channel 1.

There is an incoming DSC call so the receiver is busy.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

7

1-6 Basic Operation and Key Functions

All possible keys and their functions are listed. Note that some of the keys are not available depending on your Navman VHF radio model.

Key

Function

VOL/PWR

Volume and Power. Turn clockwise to power on. Continue to turn until a

 

comfortable volume is reached. VOL/PWR will also adjust the settings of an

 

external speaker, if connected.

SQL

Squelch or Threshold Level. Sets the threshold level for the minimum

 

receiver signal. Turn fully counterclockwise until random noise is heard, then

 

turn slowly clockwise until the random noise disappears. Make another 1/4

 

turn clockwise for best reception in open sea conditions.

 

In areas of high noise (eg close to large cities) reception may improve if

 

sensitivity is reduced. Either turn SQL slowly clockwise or use the LOCAL

 

setting. See section 2.3.

16/9

Priority Channel. VHF 7100US only. Also on the microphone. Press to

 

cancel all other modes and to tune into the priority channel. Press again to

 

return to your original channel.

 

The default is Channel 16. To make Channel 09 the priority channel, hold

 

down 16/9 until a beep sounds and 09 is displayed.

16Priority Channel. VHF 7100EU and VHF 7000 only. Also on the microphone.

Press to cancel all other modes and to tune into the priority channel, Channel 16, on high power. Press again to return to your original channel.

WX

Weather Channel. VHF 7100US and VHF 7000 only. In USA and Canadian

 

waters, press to hear the most recently selected weather station. The WX

 

symbol is displayed on the LCD.

 

Press + or - to change to a different weather channel. Press WX again to

 

return to the most recent channel.

 

If the weather alert mode (ALT) is ON and an alert tone of 1050Hz is

 

broadcast from the weather station, it is picked up automatically and the

 

alarm sounds. Press any key to hear the weather alert voice message.

8

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

H/L

Transmission Power. High (HI) 25W or Low (LO) 1W. Press to toggle

 

between high or low transmission power for the entire channel bank. The HI

 

or LO selection is shown on the LCD.

 

Some channels allow only low power transmissions. Error beeps will sound if

 

the power transmission setting is incorrect.

 

Some channels allow only low power transmissions initially, but can be

 

changed to high power by holding down H/L and PTT at the same time. See

 

Appendix C for a complete listing of channel charts.

3CH

Three Favourite Channels. Also on the microphone. Press to toggle

 

between your favourite channels. The CH1, CH2, or CH3 symbol appears on

 

the LCD to show which favourite channel is selected.

 

To scan only one of your favourite channels, press 3CH then immediately

 

press and release SCAN. If you want to scan all three favourite channels,

 

press 3CH then immediately press and hold SCAN.

 

To add a favourite channel for the first time, select that channel then hold

 

3CH to store it in the CH1 location. Repeat the procedure to store two more

 

favourite channels in the CH2 and CH3 locations respectively.

 

If you try and add another favourite channel it will overwrite the existing CH3.

 

CH1 and CH2 remain unless you delete them.

 

To delete a favourite channel, select that channel then hold down 3CH until

 

the CH1, CH2 or CH3 symbol disappears off the LCD.

UIC

Channel Bank. 7100US only. Press to toggle between USA, International

 

or Canadian channel banks. The selected channel bank is displayed on the

 

LCD along with the last used channel. All the channel charts are shown in

 

Appendix C.

U/I

Channel Bank. 7000 only. Press to toggle between channel banks. Note

 

that the channel banks available are dependent upon your VHF radio model.

 

The selected channel bank is displayed on the LCD along with the last used

 

channel. All the channel charts are shown in Appendix C.

DIM

Backlighting. 7100EU only. Press to toggle between the backlighting

 

settings. OFF will extinguish all the backlighting except for the DISTRESS

 

key. (Otherwise, use the menu to change the backlight setting.)

SCAN

Scan. Press to scan between your current channel and the priority channel in

 

DUAL or TRI WATCH mode. The weather channel is also scanned if the USA

 

channel bank is selected and the weather alert mode (ALT) is ON.

 

Hold down SCAN to enter ALL SCAN mode where the priority channel is

 

checked every 1.5 seconds.

 

When a signal is received, scanning stops at that channel and BUSY

 

appears on the screen. If the signal ceases for more than 5 seconds, the

 

scan restarts.

 

Press ENT to temporarily skip over (lock out) an “always busy” channel when

 

in ALL SCAN mode and resume the scan. An X is shown on the screen to

 

designate a skipped channel. Note that it is not possible to skip over the

 

priority channel.

 

Press SCAN to stop at the current channel.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

9

+ CH -

Channel Select. Also on the microphone. The current channel is shown on

 

the screen in BIG digits with an appropriate designator suffix A or B in small

 

letters below the channel number.

 

Press + or - to step through the available channels one at a time, or hold

 

down to scroll rapidly through all the available channels. See Appendix C for

 

a listing of channel charts.

 

Alphanumeric Entry. This key can also be used for menu selection and for

 

alphanumeric entry. Press + or - to scroll the cursor up or down menu options

 

when navigating menus.

 

When editing an item containing only numbers, press - to count through the

 

numbers or hold down to scroll rapidly.

 

To enter a character, press + to step through the alphabet or hold down to

 

scroll rapidly.

ENT

Enter. Use ENT when navigating menus, to confirm entries and edits.

ESC

Escape. Use ESC when navigating menus, to clear incorrect entries, to

 

exit from a menu without saving changes, and to back up to the previous

 

screen.

CALL/MENU

DSC Setup Menu and DSC Call Menu. 7100US and 7100EU only. Press to

 

enter the DSC Call Menu and make DSC calls. See Section 5.

 

Hold down to enter the DSC Setup Menu and customize your radio. See

 

Section 4.

MENU

Radio menu. 7000 only. Press to enter the Radio Menu and customize your

 

NAVMAN VHF radio. See Section 3.

DISTRESS

Send DSC Distress Call. 7100US & 7100EU only. See Section 6.

PTT

Press To Talk. Press PTT to transmit at any time on an allowable channel.

 

This automatically exits you from menu mode and stops scanning. You must

 

release PTT to receive a signal.

 

If PTT sticks, a built-in timer will automatically shut down a transmission after

 

five minutes and sound the error beeps.

10

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

Section 2 - The Radio Menu (MENU)

2-1 Radio Menu Options (Menu)

The following options are available through MENU (or CALL/MENU):

Maintain your buddy list.

See Section 2-2.

Set radio sensitivity.

See Section 2-3.

Set backlight level.

See Section 2-4.

Set contrast level.

See Section 2-4.

Set position & UTC manually.

See Section 2-5.

Set local time and time format.

See Section 2-5.

Radio Setup Menu.

See Section 3.

Turn the GPS Simulator on/off.

See Section 2.6.

Reset factory settings.

See Section 2.7.

Sections 1-3 and 1-4 explain how to navigate around the menu and enter, save and change data.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

11

2-2 Maintain Your Buddy List (BUDDY LIST)

MENU SELECT >BUDDY LIST LOCAL/DIST BACKLIGHT

2-2-1 Add an Entry

VHF 7100US and VHF 7100EU only.

Use the Buddy List to store the names and associated MMSIDs of 20 favourite people. Names are stored in the order of entry, with the most recent entry shown first.

The following sections show to use BUDDY LIST to add, edit, and delete entries on your buddy list.

Section 3 explains how to call a buddy.

 

 

ENTER NAME

 

ENTER NAME

 

BOB

BUDDY LIST

 

 

 

>MANUAL NEW

 

––––––––––––

 

BOB

 

123456789

ALEX

 

ENTER MMSID

 

ENTER MMSID

 

>STORE

TOM

 

–––––––––

 

123456789

 

CANCEL

 

 

 

 

 

 

 

1.Select BUDDY LIST. The cursor is at MANUAL NEW. Press ENT.

2.Enter the buddy name, one character at a time (this may be alphanumeric) then press ENT repeatedly until the cursor moves to the MMSID entry line.

4.Enter the MMSID associated with that buddy name (this must be numeric) then press ENT.

5.The new buddy name and MMSID are displayed. Press ENT to store the new entry, which is displayed at the top of your buddy list.

Note that when the BUDDY LIST is full (20 entries), you cannot make a new entry until you have deleted an existing entry.

2-2-2 Edit an Entry

BUDDY LIST

 

ALEX

 

EDIT NAME

 

 

 

 

 

ALEX

>MANUAL NEW

 

>EDIT

 

ALEX

 

111223344

ALEX

 

DELETE

 

EDIT MMSID

 

>STORE

TOM

 

 

 

112233445

 

CANCEL

 

 

 

 

 

 

 

1.Select BUDDY LIST. Press ENT to display the list of entries.

2.Scroll down (if required) to the incorrect entry and press ENT.

3.Select EDIT. The cursor is at the first character of the name.

4.Edit the buddy name or, to edit only the MMSID, press ENT repeatedly until the cursor moves to the MMSID line.

5.When you are finished, press ENT (repeatedly if necessary) to display the next screen.

6.Press ENT to store the changes. The buddy list is displayed again. If more changes are required, repeat Steps 2 thru 6. Otherwise, press ESC to exit.

12

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

2-2-3 Delete an Entry

BUDDY LIST

 

BUDDY LIST

 

TOM

 

DELETE BUDDY

>MANUAL NEW

 

MANUAL NEW

 

EDIT

 

TOM

ALEX

 

ALEX

 

>DELETE

 

>YES

TOM

 

>TOM

 

 

 

NO

 

 

 

 

 

 

 

1.Select BUDDY LIST. Press ENT to display the list of entries.

2.Scroll down (if required) to the entry you want to delete and press ENT.

3.Select DELETE then select YES.

4.The entry is deleted immediately and the buddy list is displayed again.

2-3 Local or Distance Sensitivity (LOCAL/DIST)

MENU SELECT BUDDY LIST >LOCAL/DIST BACKLIGHT

Use LOCAL/DIST to improve the sensitivity of the receiver either locally (LOCAL) or over distances (DIST).

LOCAL is not recommended for use in open sea conditions. It is designed for use in areas of high radio noise; for example, close to cities.

See also SQL (Squelch Control) in Section 1.6.

2-3-1 Set Distance Sensitivity

SENSITIVITY >DISTANT LOCAL

1.Select LOCAL/DIST then select DIST.

2.Press ENT to activate the DIST setting. This disables local sensitivity and the menu is displayed again.

2-3-2 Set Local Sensitivity

SENSITIVITY

DISTANT >LOCAL

1.Select LOCAL/DIST then scroll to LOCAL.

2.Press ENT to activate the LOCAL setting. This disables distance sensitivity and the menu is displayed again.

LOCAL is displayed on the LCD as a reminder that local sensitivity is selected.

2-4 Backlighting (BACKLIGHT) and Contrast (CONTRAST)

MENU SELECT LOCAL/DIST >BACKLIGHT CONTRAST

Use BACKLIGHT to set the backlight levels for the LCD and the keypad at a comfortable level.

The microphone keypad backlighting is either ON or OFF. Use CONTRAST to set the contrast level for the LCD.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

13

BACKLIGHT
LO HI

2-4-1 Set the Backlighting Level

1. Select BACKLIGHT.

2. Select a comfortable backlight level using + or - to change the setting.

3. Press ENT to enable the setting and return to the menu. Note that the DISTRESS key backlighting cannot be switched off.

2.4.2 Set the Contrast Level

CONTRAST LO HI

1.Select CONTRAST.

2.Select a comfortable contrast level using + or - to change the setting.

3.Press ENT to enable the setting and return to the menu.

2-5 GPS Data and Time (GPS/DATA)

MENU SELECT BACKLIGHT CONTRAST >GPS/DATA

If the boat has an operational GPS navigation receiver, the VHF radio automatically detects and updates the vessel position and the local time.

However, if the GPS navigation receiver is disconnected or absent, you can specify the vessel position and the local time manually, using the GPS/DATA option.

This information is important because it will be used if a DSC distress call is transmitted.

You can also enter the course (COG) and speed (SOG) and select GPSAlert and GPS Simulator options.

2-5-1 Manually Enter Position and UTC Time (MANUAL)

Note that this function is available only if an operational GPS receiver is not connected.

GPS/DATA

 

MANUAL LL

>MANUAL

 

––’ ––’ ––––N

SETTING

 

––’ ––’ ––––W

 

 

MAN ––:––UTC

 

 

 

1.Select GPS/DATA, then MANUAL.

2.Enter the latitude, then the longitude, then the UTC.

3.Press ENT when all the information is correct.

The vessel’s latitude and longitude are shown on the screen, with the UTC time. The prefix MAN indicates a manual entry. The manual entries are cancelled if a real GPS position is received.

2-5-2 Local Time (TIME OFFSET)

The local time can be set by entering the time offset between UTC and local time as follows.

14

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

GPS/DATA

 

GPS/DATA

 

TIME OFFSET

MANUAL

 

>TIME OFFSET

 

>+01:30

>SETTING

 

TIME FORMAT

 

02:30PM LOC

 

 

TIME DISPLY

 

 

 

 

 

 

1.Select GPS/DATA, then SETTING.

2.Select TIME OFFSET to enter the difference between UTC and local time. Half hour increments can be used with a maximum offset of ±13 hours.

In this example, a difference of +1.5 hours has been entered and the local time is displayed with the suffix LOC.

11 10

9

8

7

6

5

4

3

2

1

0

1

2

3

4

5

6

7

8

9

10 11

 

9

8

8

 

 

 

5

4

 

 

 

 

1

3

 

 

5

7

 

9

 

 

 

 

 

7

 

6

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

8

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

5.5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

9.5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

11 10

9

8

7

6

5

4

3

2

1

0

1

2

3

4

5

6

7

8

9

10 11

2-5-3 Time Format Options (TIME FORMAT)

Time can be shown in 12 or 24 hour format.

GPS/DATA

 

GPS/DATA

 

TIME FORMAT

MANUAL

 

TIME OFFSET

 

>12 Hr

>SETTING

 

>TIME FORMAT

 

24 Hr

 

 

TIME DISPLY

 

07:15AM LOC

 

 

 

 

 

1.Select GPS/DATA, then SETTING.

2.Select TIME FORMAT.

3.Select 12 Hr or 24 Hr as desired. In this example, 12 hour format has been selected and so the LCD shows the AM or PM suffix.

2-5-4 Time Display Options (TIME DISPLAY)

If you have entered the time manually as described in the previous sections, the time is always shown on the screen with the prefix M.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

15

However, if the vessel position is being updated through a GPS navigation receiver, you can switch the time display on the screen ON or OFF as follows:

GPS/DATA

 

TIME DISPLY

TIME OFFSET

 

ON

TIME FORMAT

 

>OFF

>TIME DISPLY

 

 

 

 

 

1.Select GPS/DATA, then SETTING.

2.Select TIME DISPLAY.

3.Select ON (on) or OFF (off) as desired. In this example, OFF has been selected and so the screen no longer shows the time.

If the time display is set ON, course and speed data are not displayed on the LCD (see section 2-5-6).

2-5-5 Position Display Options (LL display)

If you have entered the vessel position manually as described in the previous section, the vessel position is always shown on the screen with the suffix M.

However, if the time is being updated through a GPS navigation receiver, you can switch the vessel position display on the screen on or off as follows:

GPS/DATA

 

LL DISPLAY

TIME FORMAT

 

ON

TIME DISPLY

 

>OFF

>LL DISPLAY

 

 

 

 

 

1.Select GPS/DATA, then SETTING.

2.Select LL DISPLAY.

3.Select ON (on) or OFF (off) as desired. In this example, OFF has been selected and the screen no longer shows the vessel position.

2-5-6 Course & Speed Display Options (COG/SOG)

Use this option to display course over ground (COG) and speed over ground (SOG) data on the screen.

GPS/DATA

 

COG/SOG

TIME DISPLY

 

>ON

LL DISPLY

 

OFF

>COG/SOG

 

 

 

 

 

1.Select GPS/DATA, then SETTING.

2.Select COG/SOG.

3.Select ON (on) or OFF (off) as desired. In this example, ON has been selected and so the screen shows the bearing and speed.

If GOG/SOG is set ON (on), the time is not displayed on the screen (see section 2-5-4).

2-5-7 GPS Alert Options (ALERT)

The GPS alert is usually set to ON (on) so that if the GPS navigation receiver is disconnected, the alarm sounds.

 

 

 

1.

Select GPS/DATA, then SETTING.

GPS/DATA

 

GPS ALERT

 

2.

Select GPS ALERT.

LL DISPLY

 

>ON

3.

Select ON (on) or OFF (off) as desired.

COG/SOG

 

OFF

>GPS ALERT

 

 

 

 

 

 

 

 

 

16

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

RESET RADIO ARE YOU SURE >YES
NO
MENU SELECT
DSC SETUP
RADIO SETUP >GPS SIM

2-6 GPS Simulator (SIMULATOR)

The GPS Simulator is set to OFF whenever the radio is turned ON or whenever real GPS data is available through the COM port. However, if you want to test it, turn it on.

1. Select GPS SIM, then select ON (on) or OFF (off) as desired.

Whenever the GPS Simulator is turned ON (on), simulated Speed Over Ground (SOG), Course Over Ground (COG), and LL position appear on the screen. This data is updated automatically during the simulation.

It is not possible to send a DSC transmission when in Simulator mode.

2-7 Reset to Factory Defaults (RESET)

Use this to return every setting to the factory defaults except all MMSID settings and the entries in your buddy list.

MENU SELECT RADIO SETUP GPS SIM >RESET

1.Select RESET. The radio asks for confirmation.

2.Select YES to reset the radio and return to the menu.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

17

Section 3 - Radio Setup Menu (RADIO SETUP) 3-1 Radio Setup Menu (RADIO SETUP)

CH NAME

RING VOLUME

BEEP VOLUME

INT SPEAKER

WATCH MODE

WX ALERT

COM PORT

Edit or delete channel names.

See Section 3-2.

Set the volume level of the incoming call notification beeps. See section 3-3.

Set the volume level of the beeps.

See section 3-3.

Switch ON/OFF (on/off) the radio’s internal speakers. See section 3-4.

Selects the operation of Dual or Tri watch scanning.

See section 3-5.

(Selects if the WX Alert scanning mode is ON (on) or OFF (off). (VHF 7100US only.) See section 3-6.

Select NMEA protocol for communications between the VHF radio and any other instruments. See section 3-7.

Sections 1-3 and 1-4 explain how to navigate around the menu and enter, save and change data.

3-2 Channel Names (CH NAME)

The channel charts are listed in Appendix C with their default name tags. CH NAME gives you the option to edit or delete the channel name tags displayed on the screen.

RADIO SETUP

 

CH NAME

01

>CH NAME

 

TELEPHONE

RING VOLUME

 

 

 

 

BEEP VOLUME

 

 

 

 

 

 

 

 

 

 

 

 

EDIT CH NAME

 

EDIT CH NAME

 

TELEPHONE

 

PHONE1

 

 

 

 

>YES

 

 

 

 

NO

 

 

 

 

 

 

 

TELEPHONE >EDIT DELETE

1.Select RADIO SETUP, then CH NAME.

2.Use + or - to step through the channels with their name tags until you see the channel name tag you want to change, then press ENT. In this example, the channel name TELEPHONE associated with channel 01 is being changed to PHONE1.

3.Select EDIT and press ENT to edit the existing name tag. Input the new name over the existing name. It can be a maximum of 12 characters.

To delete the channel name, select DELETE and press ENT.

18

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

4.Press ENT (repeatedly if necessary) to display the YES/NO confirmation.

5.Press ENT to confirm the new channel name tag or the deletion, then press ESC to return to the menu.

3-3 RING & BEEP Volume (RING VOLUME) & (BEEP VOLUME)

Set the volume level of the incoming signal beeps (RING VOLUME) and/or the error and warning beeps (BEEP VOLUME) to HIGH (high) or LOW (low) as follows:

RADIO SETUP

 

RING VOLUME

 

BEEP VOLUME

CH NAME

 

>HIGH

 

>HIGH

>RING VOLUME

 

LOW

 

LOW

BEEP VOLUME

 

 

 

OFF

1.Select RADIO SETUP, then RING VOLUME or BEEP VOLUME as appropriate.

2.Select a HIGH or LOW volume. (It is possible to turn the beeps off completely by selecting BEEP VOLUME then OFF.)

3.Press ENT to enable the new volume setting and return to the menu.

3-4 Internal Speaker Connections (INT SPEAKER)

Switch the radio’s internal speaker ON (on) or OFF (off). The external speaker is always ON (on) if a speaker is plugged into the external speaker jack.

RADIO SETUP

 

INT SPEAKER

RING VOLUME

 

>ON

BEEP VOLUME

 

OFF

>INT SPEAKER

 

 

1.Select RADIO SETUP, then INT SPEAKER.

2.Select ON (on) or OFF (off) then press ENT to enable the setting and return to the menu.

3-5 Set the Priority Channel (WATCH MODE)

If you have a VHF7000 or a VHF 7100EU, watch mode is similar to a dual watch, scanning between the priority channel and the working channel. CH16 is the priority channel.

However, if you have a VHF 7100US and are operating on USA or Canadian channel banks, you can set the priority channel to cover both CH16 and CH09 as well as the working channel, as follows:

RADIO SETUP

 

WATCH MODE

BEEP VOLUME

 

>ONLY 16CH

INT SPEAKER

 

16CH+9CH

>WATCH MODE

 

 

 

 

 

1.Select RADIO SETUP, then WATCH MODE.

2.Select ONLY 16CH for dual watch mode, or 16CH+9CH for tri watch mode.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

19

3-6 Weather Alert (Wx ALERT)

VHF 7100US only.

The NOAA provides several weather forecast channels on USA and Canadian channel banks. If severe weather such as storms or hurricanes are forecast, the NOAA broadcasts a weather alert on 1050 Hz. You can set up the radio to pick up weather alerts, as follows:

RADIO SETUP

 

WX ALERT

INT SPEAKER

 

ON

WATCH MODE

 

>OFF

>WX ALERT

 

 

 

 

 

1.Select RADIO SETUP, then WX ALERT.

2.Select ON (on) or OFF (off) then press ENT to enable the setting and return to the menu.

When a weather alert is broadcast, the alarm will sound. Press any key to hear the weather alert voice message.

3-7 NMEA protocol (COM PORT)

The radio can be added to a group of instruments using NMEA protocol.

RADIO SETUP

 

NMEA

WATCH MODE

 

CHECKSUM

WX ALERT

 

>ON

>COM PORT

 

OFF

 

 

 

CHECKSUM ON is the usual setting.

1.Select RADIO SETUP, then COM PORT.

2.Select CHECKSUM ON (on) or OFF (off) then press ENT to enable the setting and return to the menu.

20

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

Section 4 - DSC Setup Menu (DSC SETUP)

These DSC facilities are available only on the 7100US and 7100EU and a valid user MMSID must be entered to access the DSC functions.

4-1 DSC Setup - Menu Options

The following options are available:

USER MMSID

GROUP SETUP

INDIV REPLY

ATIS MMSID

ATIS FUNC

DSC FUNC

LL REPLY

Enter your user MMSID. See section 4.2. (If you do not have a user MMSID, see Appendix D.)

Enter or change the name and/or details of a group.

See section 4.3.

Choose an automatic or manual response to calls (VHF 7100US only). See section 4.4.

Enter or change your ATIS MMSID (VHF 7100EU only).

See section 4.5.

Enable/disable the ATIS function (VHF 7100EU only).

See section 4.5.

Turn the DSC operation ON/OFF (on/off).

See section 4.6.

Select the type of response to an LL polling request.

See section 4.7.

Sections 1.3 and 1.4 explain how to navigate around the menu and enter, save and change data.

4-2 Enter Your USER MMSID (USER MMSID)

This is a once-only operation. You must enter your user MMSID before you can access the DSC functions.

DSC SETUP

 

INPUT USER

 

187654321

 

USER MMSID

>USER MMSID

 

MMSID

 

MMSID

 

INPUT AGAIN

GROUP SETUP

 

–––––––––

 

>STORE

 

–––––––––

INDIV REPLY

 

 

 

CANCEL

 

 

 

 

 

 

 

 

 

You can display and read your user MMSID at any time, but you get only one opportunity to enter your user MMSID.

1.Select DSC SETUP, then USER MMSID.

2.If this is the first time that you are entering your user MMSID, a dashed line appears.

Enter your user MMSID along the dashed line. Press ENT to confirm each correct entry and to move to the next digit.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

21

If you make an error, press - until < appears, then press ENT to backup and correct the entry.

3.Press ENT to store your user MMSID.

4.Enter your user MMSID again as a password check, then press ENT to permanently store the user MMSID and return to the menu.

You can view your stored user MMSID at anytime by selecting USER MMSID in the main menu.

4-3 Maintain Your Groups (GROUP SETUP)

Use GROUP SETUP to create, edit, or delete 1, 2, or 3 groups of frequently called people stored in alphanumeric order. A group MMSID always starts with 0.

4-3-1 Create a Group (GROUP SETUP)

DSC SETUP

 

GROUP SETUP

 

GROUP NAME

 

 

 

 

 

FISHER1

USER MMSID

 

>MANUAL NEW

 

––––––––––––

 

012345678

>GROUP SETUP

 

000000000

 

GROUP MMSID

 

>STORE

INDIV REPLY

 

 

 

0––––––––

 

CANCEL

 

 

 

 

 

 

 

1.Select DSC SETUP, then GROUP SETUP.

2.If this is the first time that you are entering a group name, a line of nine zeros appears. Otherwise, any existing group names are displayed. Press ENT to display the input screen.

3.Enter the group name along the dashed line. It can be alphanumeric. Press ENT to confirm each correct entry and to move to the next digit. When you have finished, press ENT repeatedly until the cursor moves to the MMSID line.

If you make an error, press - until < appears, then press ENT to backup and correct the entry.

4.Enter the group MMSID. (Note that the first number is always 0.) Press ENT.

5.The group name and group MMSID are shown in a confirmation screen. Press ENT to store the details and return to the GROUP SETUP screen.

4-3-2 Edit Group Name Details

GROUP SETUP

 

FISHER1

 

EDIT NAME

 

FISHER2

MANUAL NEW

 

>EDIT

 

FISHER1

 

012345678

>FISHER1

 

DELETE

 

EDIT MMSID

 

>STORE

FRIENDS1

 

 

 

012345678

 

CANCEL

 

 

 

 

 

 

 

1.Select DSC SETUP, then GROUP SETUP. The existing group names are displayed. Press + or - to scroll to the incorrect entry then press ENT.

2.Press ENT to edit. The group name details are displayed, with the cursor at the first character of the name.

3.Edit the buddy name or, to edit only the MMSID, press ENT repeatedly until the cursor moves to the MMSID line.

4.When you are finished, press ENT (repeatedly if necessary) to display the next screen.

5.Press ENT to store the changes and return to the GROUP SETUP screen.

22

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

4-3-3 Delete a Group

GROUP SETUP

 

FISHER2

 

DELETE

 

 

GROUP

MANUAL NEW

 

EDIT

 

FISHER2

>FISHER2

 

>DELETE

 

 

 

>YES

FRIENDS1

 

 

 

 

 

 

NO

 

 

 

 

1.Select DSC SETUP, then GROUP SETUP. The existing group names are displayed.

2.Press + or - to scroll to the incorrect entry then press ENT.

3.Select DELETE and press ENT. The radio asks for confirmation.

4.Press ENT to delete the group and return to the GROUP SETUP screen.

4-4 Response to Individual Calls (INDIV REPLY)

VHF 7100US only. You can respond to incoming individual calls with an automatic response or with a manual response.

An automatic response sends an acknowledgement and then sets the request link channel, ready for a conversation.

A manual response asks if you want to acknowledge the call, and then asks if you want to converse with the caller.

DSC SETUP

 

INDIV REPLY

1.

Select DSC SETUP, then INDIV

 

 

REPLY.

USER MMSID

 

>AUTO

2.

SelectAUTO for an automatic response,

GROUP SETUP

 

MANUAL

 

 

or MANUAL for a manual response.

>INDIV REPLY

 

 

 

 

 

 

 

 

 

 

 

 

3. Press ENT to confirm your choice and return to the menu.

4-5 ATIS MMSID & ATIS FunctionalityVHF 7100EU only. You must

enter your ATIS MMSID to access ATIS functionality if you are navigating inland waterways within Europe.

ATIS sends a digital message anytime that you release the PTT key. Inland waterways rules require 1W Tx power on Channels 06, 08, 10, 11, 12, 13, 14, 15, 17, 71, 72, 74, and 77.

4-5-1 Enter or Edit YOUR ATIS MMSID

 

 

 

DSC SETUP

 

 

 

 

 

 

 

INPUT ATIS

 

INPUT ATIS

 

INPUT AGAIN

GROUP SETUP

 

 

 

 

MMSID

 

MMSID

 

ATIS MMSID

INDIV REPLY

 

 

 

 

9––––––––

 

>STORE

 

9––––––––

>ATIS MMSID

 

 

 

 

 

 

CANCEL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ATIS MMSID 923456789 >STORE CANCEL

VHF 7100EU only. An ATIS MMSID always starts with the number 9. To enter or edit your ATIS MMSID:

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

23

1.Select DSC SETUP, then ATIS MMSID.

2.If this is the first time that you are entering your ATIS MMSID, a dashed line appears. Enter your ATIS MMSID along the dashed line. The first number is always 9. Press ENT to confirm each correct entry and to move to the next digit.

If you make an error, press - until < appears, then press ENT to backup and correct the entry.

If you are editing an existing ATIS MMSID, this will be displayed. Make the required changes.

3.Press ENT to store your user MMSID.

4.Enter your ATIS MMSID again as a password check, then press ENT to permanently store the ATIS MMSID and return to the menu.

You can view your stored ATIS MMSID at anytime by selecting ATIS MMSID in the main menu.

4-5-2 Enable ATIS Functionality (ATIS FUNC)

VHF 7100EU only. ATIS functionality will operate only after the ATIS MMSID has been entered (see previous section).

DSC SETUP

ATIS FUNC

INDIV REPLY

>ON

ATIS MMSID

OFF

>ATIS FUNC

 

ATIS

1.Select DSC SETUP, then ATIS FUNC.

2.Select ON (on) to enable the ATIS functionality and automatically disable DSC functionality. The ATIS annunciator appears on the screen.

It is not possible to have both ATIS ON (on) and DSC ON (on) simultaneously. When you enable one, the other will turn OFF (off). If DSC and ATIS are both OFF (off), DSC will have to be switched ON (on) for normal DSC operation.

There are two annunciators in the screen to show you the current mode: if the DSC annunciator is shown, DSC is operational, if the ATIS annunciator is shown, ATIS is operational.

4-6 DSC functionality options (DSC FUNC)

DSC functionality can be disabled but this is not recommended.

DSC SETUP

 

DSC FUNC

GROUP SETUP

 

>ON

INDIV REPLY

 

OFF

>DSC FUNC

 

 

 

 

 

1.Select DSC SETUP, then DSC FUNC.

2.Press ENT to select ON and to operate the DSC functionality. This will automatically disable ATIS functionality. The DSC annunciator appears on the screen.

It is not possible to have both ATIS ON (on) and DSC ON (on) simultaneously. When you enable one, the other will turn OFF (off). If DSC and ATIS are both OFF (off), DSC will have to be switched ON (on) for normal DSC operation.

24

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

There are two annunciators in the screen to show you the current mode: if the DSC annunciator is shown, DSC is operational. If the ATIS annunciator is shown, ATIS is operational.

4-7 Response Type to LL Polling Calls (LL REPLY)

You can set up the radio to respond to an LL polling request in one of three ways:

AUTO

automatically replies to any incoming LL polling requests from any of your buddies.

MANUAL

choose whether to reply automatically or manually to any incoming buddy polling

 

requests.

OFF

ignores all incoming buddy LL polling requests.

DSC SETUP

 

LL REPLY

INDIV REPLY

 

>AUTO

DSC FUNC

 

MANUAL

>LL REPLY

 

OFF

 

 

 

1.Select DSC SETUP, then LL REPLY.

2.Select your response and press ENT to confirm and return to the menu.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

25

Section 5 - Sending and Receiving DSC Calls

These DSC facilities are available only on the VHF 7100US and VHF 7100EU models, and a valid user MMSID must have been entered to access the DSC functions.

5-1 WHAT IS DSC?

DSC (Digital Selective Calling) is a semi-automated method of establishing VHF, MF, and HF radio calls. It has been designated as an international standard by the IMO (International Maritime Organization) and is part of the GMDSS (Global Maritime Distress and Safety System).

Currently, you are required to monitor Distress Channel 16, but DSC will eventually replace listening watches on distress frequencies and will be used to broadcast routine and urgent maritime safety information.

DSC enables you to send and receive calls from any vessel or coast station that is equipped with DSC functionality, and within geographic range. Calls can be categorised as distress, urgency, safety, or routine, and DSC selects a working channel automatically.

5-2 Sending DSC calls

>INDIVIDUAL INDIV ACK LAST GROUP

1.Press CALL MENU to show the types of DSC call that can be made.

Note that only four DSC call types can be shown at any one time on the screen.

2.Press + or - to scroll up and down the DSC call types until the cursor is positioned at the desired option. Then press ENT. The DSC call types are:

INDIVIDUAL

LAST CALL

GROUP

ALL SHIPS

CALL LOG

DIST LOG

LL REQUEST

Make a routine call or acknowledgement to a new caller or a buddy. See Section 5-2-1, 5-2-2, and 5-2-3.

Show the details of the most recent incoming call.

See Section 5-2-4.

Make a call to one of your three groups.

See Section 5-2-5.

Make an All Ships call.

See Section 5-2-6.

Show the details of the 20 most recent incoming calls.

See Section 5-2-7.

Show the details of the 10 most recent distress calls.

See Section 5-2-8.

Request the LL position of a buddy.

See Section 5-2-9.

26

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

5-2-1 Make a Routine Call (Individual)

 

 

 

 

 

 

 

 

 

 

 

DSC CALL

 

INDIVIDUAL

 

MANUAL MMSID

 

012345678

>INDIVIDUAL

 

>MANUAL NEW

 

0––––––––

 

INDIVIDUAL

LAST CALL

 

BOBBY D

 

 

 

ROUTINE

GROUP

 

REBECCA T

 

 

 

>SET CHANNEL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

012345678

 

12345678

 

012345678

 

INDIV ACK

INDIVIDUAL

 

INDIVIDUAL

 

INDIVIDUAL

 

012345678

ROUTINE

 

ROUTINE

 

ROUTINE

 

PRESS PTT

>SEND?

 

CALLING...

 

WAITING ACK

 

ESC –> EXIT

 

 

 

 

 

 

 

You can call any other person that has another DSC equipped radio.

1.Press CALL/MENU to enter DSC mode, then select INDIVIDUAL. This allows you to call another person.

2.Select MANUAL NEW to call a person that is not in your buddy list, otherwise select the name of your buddy. Press ENT.

If you selected MANUAL NEW, you need to enter the user MMSID and then press ENT.

3.Select the working channel and press ENT. (Note: Duplex channels cannot usually be called and are automatically eliminated from the suggested call list. If the call is to a Coast Station, the radio will recognize this and select the correct channel.)

4.The radio summarizes the call details and asks for confirmation to send the call (SEND?). Press ENT to send the call. The radio goes to CH70 and the Tx annunciator is displayed on the screen while the DSC call is being sent.

5.If the call is acknowledged (ACK), press PTT to talk. If there is no reply, retry making the call. See Section 5-2-2.

5-2-2 Retrying a Routine Call

VHF7100 SEND AGAIN? >YES CANCEL

1.If there is no reply to your call after one minute (UNABLE TO ACKNOWLEDGE) the radio asks if you want to retry the call (SEND AGAIN?).

2.Select YES and press ENT to retry the call.

The radio will repeat this cycle twice. If the call still cannot be placed, the radio returns to normal operation.

5-2-3 Acknowledgement of an Individual Incoming Call (INDIV)

RCV: INDIV 012345678 ENTER –> ACK

ESC –> EXIT

The VHF 7100EU requires the operator to manually send an acknowledgement to the requesting radio.

Press ENT to send an acknowledgement or ESC to cancel.

The VHF 7100US will automatically send an acknowledgement to the requesting radio within 10 seconds of receiving the call.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

27

5-2-4 Recall the Most Recent Incoming Call (LAST)

 

 

 

 

 

 

 

 

DSC CALL

 

VHF7100 USA

 

VHF7100 USA

 

VHF7100 USA

INDIVIDUAL

 

INDIVIDUAL

 

INDIVIDUAL

 

INDIVIDUAL

>LAST CALL

 

ROUTINE

 

ROUTINE

 

ROUTINE

GROUP

 

10:22AM LOC

 

>SET CHANNEL

 

>SEND?

 

 

 

 

 

 

 

This facility is useful and used frequently.

1.Press CALL/MENU to enter DSC mode. LAST CALL is automatically selected. Press ENT to display the contact details of the most recent incoming call.

2.Select the working channel and press ENT. (Note: Duplex channels cannot usually be called and are automatically eliminated from the suggested call list. If the call is to a Coast Station, the radio will recognize this and select the correct channel.)

3.The radio summarizes the call details and asks for confirmation to send the call (SEND?). Press ENT to send the call, and continue as explained in Section 5-2-1.

5-2-5 Call a Group (GROUP)

DSC CALL

 

SELECT GROUP

 

RD GROUP

 

VHF7100 USA

INDIVIDUAL

 

>RD GROUP

 

055554444

 

INDIVIDUAL

LAST CALL

 

GROUP #2

 

ROUTINE

 

ROUTINE

>GROUP

 

GROUP#3

 

>SET CHANNEL

 

>SEND?

 

 

 

 

 

 

 

1.Press CALL MENU to enter DSC mode, then select GROUP. The radio displays the names of your groups.

2.Select the group that you want to call (the Group MMSID must be set before making the call). Then set the channel and continue as explained in Section 5-2-1.

5-2-6 CALL ALL SHIPS (ALL SHIPS)

DSC CALL

 

ALL SHIPS

 

ALL SHIPS

LAST CALL

 

>URGENCY

 

URGENCY

GROUP

 

SAFETY

 

>YES

>ALL SHIPS

 

ROUTINE

 

NO

 

 

 

 

 

The ALL SHIPS ROUTINE call option is shown only on the VHF 7100US.

1.Press CALL MENU to enter DSC mode, then select ALL SHIPS.

2.The priority is set automatically to URGENCY. However, you can select one of the following call priorities:

URGENCY for use when a serious situation or problem arises that could lead to a distress situation

SAFETY to send safety information to all other vessels in range; ROUTINE routine call (VHS 7100US only).

3.CH16 is selected automatically as the working channel and the radio asks for confirmation of the ALL SHIPS call. Press ENT to select YES and send the call. Continue as explained in Section 5-2-1.

28

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

5-2-7 Call using the Call Log (CALL LOG

 

 

 

 

 

 

 

 

 

 

DSC CALL

 

11 VHF7100

 

VHF7100

 

VHF7100

GROUP

 

INDIVIDUAL

 

>CALL BACK

 

INDIVIDUAL

ALL SHIPS

 

ROUTINE

 

DELETE

 

ROUTINE

>CALL LOG

 

10:45PM LOC

 

 

 

>SET CHANNEL

 

 

 

 

 

 

 

VHF7100 INDIVIDUAL ROUTINE >SEND?

The Call Log contains the contact details for the 20 most recent incoming calls, so that you call any of them again quickly.

1.Press CALL MENU to enter DSC mode, then select CALL LOG. Scroll down to the desired contact details.

The radio displays the contact details for the most recent incoming call as the first entry

(01)in the call log. In the example, the contact details for the 11th most recent call are displayed.

2.Press ENT to confirm the call back, then set the working channel and press ENT to send the call. Continue as explained in Section 5-2-1.

5.2.8 Call using the Distress Log (DIST LOG)

DSC CALL

 

02 10:03 UTC

 

DISTRESS

 

VHF7100

ALL SHIPS

 

VHF7100 (xxx)

 

RELAY

 

>CALL BACK

CALL LOG

 

82º50. N

 

PIRACY

 

DELETE

>DIST LOG

 

27º45. W

 

987654321

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VHF7100

 

VHF7100

 

 

 

 

INDIVIDUAL

 

INDIVIDUAL

 

 

 

 

ROUTINE

 

ROUTINE

 

 

 

 

>SET CHANNEL

 

>SEND?

 

 

 

 

 

 

 

 

 

 

 

The Distress Log contains the Distress Log data for the 10 most recent relayed Distress Calls, so that you can call any of them quickly. Always try to make voice contact on CH16 first, as follows:

1.Press CALL/MENU to enter DSC mode, then select DIST LOG.

2.The most recently received Distress Call Is the first entry (01) in the Distress Log. Select the entry that you want to call and press ENT.

The details are displayed over two screens that alternate every 1.5 seconds; the first screen shows the location and name or MMSID of the vessel in Distress, the second screen shows the nature of the emergency (if specified) and the MMSID of the vessel that relayed the Distress Call.

3.Set the channel and continue as explained in Section 5-2-1.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

29

5-2-9 Request the LL Position of a Buddy (LL REQUEST)

DSC CALL

 

LL REQUEST

 

SAM

 

SAM

CALL LOG

 

>SAM

 

LL REQUEST

 

LL REQUEST

DIST LOG

 

VHF7100

 

>SEND?

 

 

>LL REQUEST

 

BUDDY #3

 

 

 

CALLING...

 

 

 

 

 

 

channel name SAM

LL REQUEST AWAITING ACK

1.Press CALL/MENU to enter DSC mode, then select LL REQUEST.

2.Select the buddy whose LL position you want to request then press ENT to send the request. (See Section 5-3-5 for the acknowledgement.)

3.The working channel name is displayed while the radio waits for an acknowledgement from your buddy. If there is no reply after 1 minute the radio asks if you want to retry. Continue as

explained in Section 5-2-2.

5-3 Receiving DSC Calls

Several types of DSC calls can be received from vessels within range at various priority levels:

DISTRESS

See Section 6.

ALL SHIPS

Urgency or Safety priority (see Section 5-3-1)

INDIVIDUAL

Urgency, Safety, or Routine priority (see Section 5-3-2)

GROUP

Routine priority only (see Section 5-3-3)

GEOGRAPHIC

Routine priority only (see Section 5-3-4)

POLLED POSITION

Routine priority only (see Section 5-3-5)

In addition to the audible alert, the telephone icon will flash on the screen.

30

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

5-3-1 Receiving an All Ships Call (ALL SHIPS)

RCV: ALL SHIP priority VHF7100 ESC –> EXIT

1.When you receive notification of an ALL SHIP call, press any key to cancel the alert. The radio automatically selects CH16.

The priority level and the user MMSID are displayed on the screen. If the radio recognises the user MMSID as one of your buddies, the buddy’s name is displayed in place of the user MMSID.

2.No acknowledgement is required. Press PTT to initiate voice contact on CH16 and then switch to a working channel.

The call data is stored in the Call Log (see Section 5-2-7).

5-3-2 Receiving an Individual Call (INDIV)

RCV: INDIV

 

INDIV ACK

VHF7100

 

VHF7100

ENTER –> ACK

 

PRESS PTT

ESC –> EXIT

 

ESC –> EXIT

 

 

 

1.When you receive notification of an INDIV call, press any key to cancel the alert. The radio automatically selects the channel designated in the incoming call. INDIV calls are almost always Routine priority.

If the radio recognises the user MMSID as one of your buddies, the buddy’s name is displayed in place of the user MMSID.

2.The VHF 7100US responds automatically but the VHF 7100EU prompts you to press ENT to acknowledge the incoming call.

3.The caller should respond to your acknowledgement by making voice contact on the designated channel. If this does not happen, you can press PTT to initiate voice contact instead.

The call data is stored in the Call Log (see Section 5-2-7).

5-3-3 Receiving a Group Call (GROUP)

RCV: GROUP GP: RD GROUP VHF7100 ROUTINE

1.When you receive notification of a GROUP call, press any key to cancel the alert. The radio automatically selects the channel designated in the incoming call.

The priority level is always routine, and the group is identified on the screen. The group will be one of the three groups of frequently called people that you set up earlier (see Section 4-3).

2.You do not need to send an acknowledgement. If desired, press PTT to initiate voice contact on the designated channel.

The call data is stored in the Call Log (see Section 5-2-7).

5-3-4 Receiving a Geographic Call (GEOGRAPH)

RCV: GEOGRAPH VHF7100

10:34 UTC

ESC –> EXIT

A geographic call is received by vessels within a specific geographic boundary area.

1.When you receive notification of a GEOGRAPH call, press any key to cancel the alert. The radio automatically selects the channel designated in the incoming call.

The time and the user MMSID or name are displayed on the screen. If the radio recognises the user MMSID as one of your buddies, the buddy’s name is displayed in place of the user MMSID.

2. Monitor the working channel for an announcement from the calling vessel.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

31

5-3-5 Receiving a Polled Position Call (POSITION)

RCV: POSITION SAM

82º50. 003'N 27º45.543'W

1.When you receive GPS position data from a buddy in response to your LL request (see Section 5-2-9), you are recommended to make a written note of the position, especially if it is a good fishing position.

If enhanced LL position information is available from your buddy, this is shown on the screen until the screen display changes.

32

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

Section 6 - Distress Calls

This DSC function is available only on the 7100US and 7100EU models, and a valid user MMSID must have been entered to access this DSC function.

6-1 Sending a Distress Call

DISTRESS CALL

 

DISTRESS CALL

 

DISTRESS CALL

>PIRACY

 

>PIRACY

 

SENT! WAIT..

OVER BOARD

 

HOLD DISTRESS

 

PRESS ESC

EPRIB

 

2 SECONDS..

 

TO CANCEL...

 

 

 

 

 

1.Open the red cover labelled DISTRESS.

If time is available to specify the nature of the distress, go to step 2. Otherwise, go directly to step 3.

2.Press the DISTRESS key to display the following categories. Scroll to the category that describes your situation, then press ENT:

UNDEFINED

FIRE

FLOODING

COLLISION

GROUNDING

LISTING

SINKING

ADRIFT

ABANDONING

PIRACY

OVER BOARD

EPRIB

3.Hold down the DISTRESS key for about 3 seconds, until you see the distress call sent message (DISTRESS CALL SENT!) on the screen. The whole display starts to flash and beep loudly.

The distress call repeats five times continuously. It then repeats randomly every 3.5 to 4.5 minutes until a distress acknowledgement (DISTRESS ACK) is received from a search and rescue authority or until you cancel the distress call manually.

The radio selects CH16 automatically so that you can hear any incoming voice contacts from search and rescue authorities or other vessels within range.

Press ESC if you need to cancel the distress call. This is the only key that operates in distress mode.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

33

6-2 Receiving a Distress Call (DISTRESS!)

RCV: DISTRESS

 

RCV: DISTRESS

123456789

 

10:34 UTC

FLOODING

 

82º50.003'N

ESC –> EXIT

 

27º45.543'W

 

 

 

1.An alert sounds when a distress call (DISTRESS!) is received. Press any key to cancel the alert. You do not need to send an acknowledgement.

2.The radio automatically selects CH16 and displays the details of the distress call on the screen. Press PTT to establish voice contact.

The details are displayed over two screens that alternate every 1.5 seconds; the first screen shows the user MMSID and nature of the emergency (if specified), the second screen shows the time and the location (if specified). If the location and time are not specified, these are replaced with sequences of 9s and 8s respectively.

The VHF7100 is capable of receiving enhanced LL position data if the vessel transmitting the Distress Call is sending this. This provides the position of the distressed vessel to within 20 m (60ft).

6-3 Distress Acknowledgement (DISTRESS ACK) or Relay

RCV: DISTRESS RELAY 123456789 ESC –> EXIT

An alert sounds when a Distress Relay (DISTRESS RELAY) is received. Press any key to cancel the alert.

Try to make voice contact with the calling vessel. Maintain a listening watch on CH16 and standby to lend assistance.

For a Distress Acknowledgement (DISTRESS ACK) sent from the Coast Guard, your radio automatically cancels Distress Mode transmissions and CH16 appears. Press PTT to establish voice contact with the Coast Guard.

The Coast Guard is the only agency allowed to send a Distress Acknowledgement (DISTRESS ACK).

34

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

Appendix A - Technical Specifications

Navman VHF 7000

GENERAL

 

Power Supply:

13.6 V DC.

Current drain:

 

Transmit

6A at 25W Tx / 1.5A at 1W Tx

Receive

Less than 250 mA in standby

Useable channels:

International, USA (country specific)

Mode:

16K0G3E (FM)

PHYSICAL

 

LCD display (viewing):

41(H) x 53(W) mm

 

FSTN 4 x 12 character

Contrast and

 

Dimming control:

Yes

Antenna connector:

SO-239 (50 ohm)

Temperature Range:

-15ºC to +50ºC

Waterproof:

JIS-7

Dimensions:

161(W) x 75(H) x 147(D) mm - without bracket

Weight:

1.29 kg (2.8lbs) - without microphone

Frequency stability:

+/- 10ppm

Frequency control:

PLL

GPS/NMEA input:

Yes

Comm. port:

4800 baud NMEA

DSC:

No

FEATURES

 

Flush Mount kit and

 

dust cover:

Yes

Local/Distant control:

Yes

Position polling:

No

GPS Position & Data:

Yes

Call logs:

Yes - 20 individual and 10 distress

DSC (USCG SC101

 

and Class D):

No

Channel Naming:

Yes

Dual Watch, Favourite

 

channel scan, All scan:

Yes

User programmable

 

MMSID:

No

MMSID and NAME

 

directory:

No

TRANSMITTER

 

Frequency:

156.025 - 157.425MHz

Output power:

25 W / 1 W selectable

Transmitter protection:

Open / short circuit of antenna

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

35

Max Freq deviation:

+/- 5kHz

Spurious & harmonics:

80dB@25W, 60dB@1W

Modulation distortion:

Less than 4%@ 1kHz for a +/-3kHz deviation

RECEIVER

 

Frequency:

156.025 - 163.275MHz

12dB SINAD sensitivity:

0.25uV (distant) / 2.5uV (local)

20db SINAD sensitivity:

0.35uV

Adjacent CH selectivity:more than 70db

Spurious response:

more than 70db

Intermodulation

 

Rejection ratio:

more than 68db

Residual Noise level:

more than -40db unsquelched

Audio output power:

2W (with 8 ohm at 10% distortion)

 

4W with 4 ohm external speaker

Compass safe distance:

0.5m (1.5')

Specifications are subject to change without notice.

Navman VHF 7100

GENERAL

 

Power Supply:

13.6V DC.

Current drain:

 

Transmit

6 A at 25 W Tx / 1.5A at 1W Tx

Receive

Less than 250mA in standby

Useable channels:

International, USA, Canada, Weather (country specific)

Mode:

16K0G3E (FM) / 16K0G2B (DSC)

PHYSICAL

 

LCD display (viewing):

41(H) x 53(W) mm

 

FSTN 4 x 12 character

Contrast and

 

Dimming control:

Yes

Antenna connector:

SO-239 (50 ohm)

Temperature Range:

-15ºC to +50ºC

Waterproof:

JIS-7

Dimensions:

161(W) x 75(H) x 147(D) mm - without bracket

Weight:

1.29 kg (2.8 lbs) - without microphone

Frequency stability:

+/- 10ppm

Frequency control:

PLL

GPS/NMEA input:

Yes

Comm. port:

4800 baud NMEA

DSC:

Yes

FEATURES

 

Flush Mount kit and

 

dust cover:

Yes

Local/Distant control:

Yes

36

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

Position polling:

Yes

Group Call:

Yes

Call logs:

Yes - 20 individual and 10 distress

DSC (USCG SC101

 

and Class D):

Yes (VHS 7100US)

Channel Naming:

Yes

Tri watch, Favourite

 

channel scan, All scan:

Yes

User programmable

 

MMSID:

Yes

MMSID and NAME

 

directory:

Yes - 20 numbers & group

TRANSMITTER

 

Frequency:

156.025 - 157.425MHz

Output power:

25 W / 1 W selectable

Transmitter protection:

Open / short circuit of antenna

Max Freq deviation:

+/- 5kHz

Spurious & harmonics:

better than 2.5µ W

Modulation distortion:

Less than 4%@ 1kHz for a +/-3kHz deviation

RECEIVER

 

Frequency:

156.025 - 163.275 MHz

12dB SINAD sensitivity:

0.25uV (distant) / 2.5uV (local)

20db SINAD sensitivity:

0.35uV

Adjacent CH selectivity:more than 65db (VHS 7100US)

 

more than 70 db (VHS 7100EU)

Spurious response:

more than 65 db (VHS 7100US)

 

more than 70 db (VHS 7100EU)

Intermodulation

 

Rejection ratio:

more than 65 db (VHS 7100US)

 

more than 68 db (VHS 7100EU)

Residual Noise level:

more than -40db unsquelched

Audio output power:

2 W (with 8 ohm at 10% distortion)

 

4 W with 4 ohm external speaker

Compass safe distance:

0.5 m (1.5')

Specifications are subject to change without notice.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

37

Appendix B - Troubleshooting

1. The transceiver will not power up.

A fuse may have blown OR there is no voltage getting to the transceiver.

a)Check the power cable for cuts, breaks, or squashed sections.

b)After checking the wiring, replace the 7 Amp fuse (2 spare fuses are supplied).

c)Check the battery voltage. This must be greater than 10.5V.

2.The transceiver blows the fuse when the power is switched on.

The power wires may have been reversed.

a)Check that the red wire is connected to the positive battery terminal, and the black wire is connected to the negative battery terminal.

3.The speaker makes popping or whining noises when the engine is running.

Electrical noise may be interfering with the transceiver.

a)Re-route the power cables away from the engine.

b)Add a noise suppressor to the power cable.

c)Use resistive spark plug wires and/or use an alternator whine filter.

4.No sound from the external speaker.

a)Check that the external speaker cable is physically connected.

b)Check the soldering of the external speaker cable.

5.Transmissions are always on low power, even when high (HI) power is selected.

The antenna may be faulty.

a)Test the transceiver with a different antenna.

b)Have the antenna checked out.

6.Battery symbol is displayed.

The power supply is too low or too high.

a)Check the battery voltage. This should be at least 10.5V ± 0.5V DC.

b)Check the alternator on the vessel.

7.No position information is displayed.

The GPS cable may faulty or the GPS setting may be incorrect.

a)Check that the GPS cable is physically connected.

b)Check the polarity of the GPS cable.

c)Check the baud rate setting of the GPS if applicable. The baud rate setting should be 4800 and parity should be set to NONE.

38

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

Appendix C - VHF Marine Channel Charts

C.1 International Channel Chart

CH

SEND

RECEIVE

TRAFFIC TYPE

SHIP

SHIP

NAME TAG

 

(MHz)

(MHz)

 

TO

TO

 

 

 

 

 

SHIP

SHORE

 

01

156.050

160.650

Public Correspondence, Duplex

No

Yes

TELEPHONE

02

156.100

160.700

Public Correspondence, Duplex

No

Yes

TELEPHONE

03

156.150

160.750

Public Correspondence, Duplex

No

Yes

TELEPHONE

04

156.200

160.800

Port Operations, Duplex

No

Yes

PORT OPS

05

156.250

160.850

Port Operations, Selected VTS Areas

No

Yes

PORT OPS/VTS

06

156.300

156.300

Inter-ship Safety

Yes

No

SAFETY

07

156.350

160.950

Port Operations, Duplex

No

Yes

PORT OPS

08

156.400

156.400

Commercial (inter-ship only)

Yes

No

COMMERCIAL

09

156.450

156.450

Recreational Calling Channel

Yes

Yes

CALLING

10

156.500

156.500

Commercial

Yes

Yes

COMMERCIAL

11

156.550

156.550

Commercial, VTS in Selected Areas

Yes

Yes

VTS

12

156.600

156.600

Port Operations, Selected VTS Areas

Yes

Yes

PORT OPS/VTS

13

156.650

156.650

Intership Navigation Safety (bridge-

Yes

No

BRIDGE COM

 

 

 

to-bridge)

 

 

 

14

156.700

156.700

Port Operations, Selected VTS Areas

Yes

Yes

PORT OPS/VTS

15 1

156.750

156.750

Port Operations – 1W Only

Yes

Yes

PORT OPS

16

156.800

156.800

International Distress, Safety, and

Yes

Yes

DISTRESS

 

 

 

Calling

 

 

 

17 1

156.850

156.850

State Controlled – 1W Only

Yes

Yes

SAR

18

156.900

161.500

Port Operations, Duplex

No

Yes

PORT OPS

19

156.950

161.550

Commercial, Duplex

No

Yes

SHIP - SHORE

20

157.000

161.600

Port Operations, Duplex

No

Yes

PORT OPS

21

157.050

161.650

Port Operations, Duplex

No

Yes

PORT OPS

22

157.100

161.700

Port Operations, Duplex

No

Yes

PORT OPS

23

157.150

161.750

Public Correspondence, Duplex

No

Yes

TELEPHONE

24

157.200

161.800

Public Correspondence, Duplex

No

Yes

TELEPHONE

25

157.250

161.850

Public Correspondence, Duplex

No

Yes

TELEPHONE

26

157.300

161.900

Public Correspondence, Duplex

No

Yes

TELEPHONE

27

157.350

161.950

Public Correspondence, Duplex

No

Yes

TELEPHONE

28

157.400

162.000

Public Correspondence, Duplex

No

Yes

TELEPHONE

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

39

CH

SEND

RECEIVE

TRAFFIC TYPE

SHIP

SHIP

NAME TAG

 

 

(MHz)

(MHz)

 

TO

TO

 

 

 

 

 

 

 

SHIP

 

 

 

 

60

156.025

160.625

Public Correspondence, Duplex

No

Yes

 

TELEPHONE

 

61

156.075

160.675

Port Operations, Duplex

No

Yes

PORT OPS

 

62

156.125

160.725

Port Operations, Duplex

No

Yes

PORT OPS

 

63

156.175

160.775

Port Operations, Duplex

No

Yes

PORT OPS

 

64

156.225

160.825

Public Correspondence, Duplex

No

Yes

TELEPHONE

 

65

156.275

160.875

Port Operations, Duplex

No

Yes

PORT OPS

 

66

156.325

160.925

Port Operations, Duplex

No

Yes

PORT OPS

 

67

156.375

156.375

Commercial, bridge-to-bridge

Yes

No

BRIDGE COM

 

68

156.425

156.425

Boat Operations, Recreational

Yes

No

SHIP - SHIP

 

69

156.475

156.475

Port Operations

Yes

Yes

PORT OPS

 

70 3

156.525

156.525

Digital Selective Calling - DSC

------

------

DSC

 

71

156.575

156.575

Port Operations

Yes

Yes

PORT OPS

 

72

156.625

156.625

Intership

Yes

No

SHIP - SHIP

 

73

156.675

156.675

Port Operations

Yes

Yes

PORT OPS

 

74

156.725

156.725

Port Operations

Yes

Yes

PORT OPS

 

77

156.875

156.875

Intership

Yes

No

SHIP - SHIP

 

78

156.925

161.525

Non-Commercial, Duplex

No

Yes

SHIP - SHORE

 

79

156.975

161.575

Commercial, Duplex

No

Yes

SHIP - SHORE

 

80

157.025

161.625

Commercial, Duplex

No

Yes

SHIP - SHORE

 

81

157.075

161.675

Port Operations, Duplex

No

Yes

PORT OPS

 

82

157.125

161.725

Port Operations, Duplex

No

Yes

PORT OPS

 

83

157.175

161.775

Public Correspondence, Duplex

No

Yes

TELEPHONE

 

84

157.225

161.825

Public Correspondence, Duplex

No

Yes

TELEPHONE

 

85

157.275

161.875

Public Correspondence, Duplex

No

Yes

TELEPHONE

 

86

157.325

161.925

Public Correspondence, Duplex

No

Yes

TELEPHONE

 

87

157.375

161.975

Public Correspondence, Duplex

No

Yes

TELEPHONE

 

88

157.425

162.025

Public Correspondence, Duplex

No

Yes

TELEPHONE

 

40

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

WEATHER

 

MHz

TRAFFIC TYPE

 

 

NAME TAG

Wx01

RX Only

162.550

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx02

RX Only

162.400

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx03

RX Only

162.475

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx04

RX Only

162.425

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx05

RX Only

162.450

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx06

RX Only

162.500

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx07

RX Only

162.525

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx08

RX Only

161.650

CANADIAN WEATHER CHANNEL

------

------

CANADA WX

Wx09

RX Only

161.775

CANADIAN WEATHER CHANNEL

------

------

CANADA WX

Wx10

RX Only

163.275

NOAA WEATHER CHANNEL

------

------

NOAA WX

SPECIAL NOTES ON INTERNATIONAL CHANNEL USAGE

1.LOW POWER (1W) only.

2.LOW POWER (1W) initially. Override to HIGH POWER by holding down H/L key before transmitting. Used normally in bridge-to-bridge communications.

3.Channel 70 is designated for use exclusively for Digital Selective Calling (DSC), such as Distress, Safety, and Ship Calls. No voice communication is allowed on CH70.

4.The INTERNATIONAL mode is not legal for use in U.S. or Canada waters.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

41

CH

SEND

RECEIVE

TRAFFIC TYPE

SHIP

SHIP

NAME TAG

 

(MHz)

(MHz)

 

TO

TO

 

 

 

 

 

SHIP

SHORE

 

01A

156.050

156.050

Port Operations, Selected VTS Areas

Yes

Yes

PORT OPS/VTS

03A4

156.150

156.150

US Government, Coast Guard

Yes

Yes

UNAUTHORIZED

05A

156.250

156.250

Port Operations, Selected VTS Areas

Yes

Yes

PORT OPS/VTS

06

156.300

156.300

Inter-ship Safety

Yes

No

SAFETY

07A

156.350

156.350

Commercial

Yes

Yes

COMMERCIAL

08

156.400

156.400

Commercial (inter-ship only)

Yes

No

COMMERCIAL

09

156.450

156.450

Recreational Calling Channel

Yes

Yes

CALLING

10

156.500

156.500

Commercial

Yes

Yes

COMMERCIAL

11

156.550

156.550

Commercial, VTS in Selected

Yes

Yes

VTS

 

 

 

Areas

 

 

 

12

156.600

156.600

Port Operations, Selected VTS Areas

Yes

Yes

PORT OPS/VTS

13 3

156.650

156.650

Intership Navigation Safety

Yes

No

BRIDGE COM

 

 

 

(bridge-to-bridge), 1W with

 

 

 

 

 

 

Power-up

 

 

 

14

156.700

156.700

Port Operations, Selected VTS Areas

Yes

Yes

PORT OPS/VTS

15 2

RX Only

156.750

Environmental, RX Only

------

------

ENVIROMENTAL

16

156.800

156.800

International Distress, Safety, and

Yes

Yes

DISTRESS

 

 

 

Calling

 

 

 

17 1

156.850

156.850

State Controlled – 1W Only

Yes

Yes

SAR

18A

156.900

156.900

Commercial

Yes

Yes

COMMERCIAL

19A

156.950

156.950

Commercial

Yes

Yes

COMMERCIAL

20

157.000

161.600

Port Operations, Canadian Coast

No

Yes

PORT OPS

 

 

 

Guard, Duplex

 

 

 

20A

157.000

157.000

Port Operations

Yes

Yes

PORT OPS

21A4

157.050

157.050

U.S. Government, Canadian

Yes

Yes

UNAUTHORIZED

 

 

 

Coast Guard

 

 

 

22A

157.100

157.100

Coast Guard Liaison

Yes

Yes

COAST GUARD

23A 4

157.150

157.150

U.S. Government, Coast Guard

Yes

Yes

UNAUTHORIZED

24

157.200

161.800

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

Operator

 

 

 

25

157.250

161.850

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

Operator

 

 

 

26

157.300

161.900

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

Operator

 

 

 

27

157.350

161.950

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

Operator

 

 

 

28

157.400

162.000

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

Operator

 

 

 

42

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

CH

SEND

RECEIVE

TRAFFIC TYPE

SHIP

SHIP

NAME TAG

 

(MHz)

(MHz)

 

TO

TO

 

 

 

 

 

SHIP

 

 

61A 4

156.075

156.075

U.S. Government, Canadian

Yes

Yes

UNAUTHORIZED

 

 

 

Coast Guard

 

 

 

63A

156.175

156.175

Port Operations, VTS in Selected

Yes

Yes

PORT OPS/VTS

 

 

 

Areas

 

 

 

64A 4

156.225

156.225

U.S. Government, Canadian

Yes

Yes

UNAUTHORIZED

 

 

 

Commercial Fishing

 

 

 

65A

156.275

156.275

Port Operations

Yes

Yes

PORT OPS

66A

156.325

156.325

Port Operations

Yes

Yes

PORT OPS

67 3

156.375

156.375

Commercial, bridge-to-bridge, 1W

Yes

No

BRIDGE COM

 

 

 

with Power-up

 

 

 

68

156.425

156.425

Boat Operations, Recreational

Yes

No

SHIP - SHIP

69

156.475

156.475

Boat Operations, Recreational

Yes

Yes

PLEASURE

70 6

156.525

156.525

Digital Selective Calling - DSC

------

------

DSC

71

156.575

156.575

Boat Operations, Recreational

Yes

Yes

PLEASURE

72

156.625

156.625

Boat Operations, Recreational

Yes

No

SHIP - SHIP

73

156.675

156.675

Port Operations

Yes

Yes

PORT OPS

74

156.725

156.725

Port Operations

Yes

Yes

PORT OPS

77 1

156.875

156.875

Port Operations –1W Only

Yes

Yes

PORT OPS

78A

156.925

156.925

Boat Operations, Recreational

Yes

No

SHIP - SHIP

79A

156.975

156.975

Commercial

Yes

Yes

COMMERCIAL

80A

157.025

157.025

Commercial

Yes

Yes

COMMERCIAL

81A 4

157.075

157.075

U.S. Government, Environmental

Yes

Yes

UNAUTHORIZED

 

 

 

Protection Agency Operations

 

 

 

82A 4

157.125

157.125

U.S. Government, Canadian

Yes

Yes

UNAUTHORIZED

 

 

 

Coast Guard

 

 

 

83A 4

157.175

157.175

U.S. Government, Canadian

Yes

Yes

UNAUTHORIZED

 

 

 

Coast Guard

 

 

 

84

157.225

161.825

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

Operator

 

 

 

85

157.275

161.875

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

Operator

 

 

 

86

157.325

161.925

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

Operator

 

 

 

87

157.375

161.975

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

Operator

 

 

 

88

157.425

162.025

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

Operator

 

 

 

88A

157.425

157.425

Commercial, Intership Only

Yes

No

COMMERCIAL

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

43

WEATHER

 

MHz

TRAFFIC TYPE

 

 

NAME TAG

Wx01

RX Only

162.550

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx02

RX Only

162.400

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx03

RX Only

162.475

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx04

RX Only

162.425

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx05

RX Only

162.450

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx06

RX Only

162.500

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx07

RX Only

162.525

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx08

RX Only

161.650

CANADIAN WEATHER CHANNEL

------

------

CANADA WX

Wx09

RX Only

161.775

CANADIAN WEATHER CHANNEL

------

------

CANADA WX

Wx10

RX Only

163.275

NOAA WEATHER CHANNEL

------

------

NOAA WX

SPECIAL NOTES ON USA CHANNEL USAGE

1.LOW POWER (1 W) only.

2.Receive Only.

3.LOW POWER (1 W) initially. Override to HIGH POWER by holding down H/L key before transmitting. Used normally in bridge-to-bridge communications.

4.Lightly Shaded Simplex channels 03A, 21A, 23A, 61A, 64A, 81A, 82A, and 83A cannot be lawfully used in U.S. waters unless special authorization is obtained from the U.S. Coast Guard. Not for use by the general public.

5.The letter “A” illuminated by the channel number indicates the USA channel is simplex. This same channel is always duplex when selecting International. There is no “A” reference for International channels. The letter “B” is only used for some Canadian “Receive Only” channels.

6.Channel 70 is designated for use exclusively for Digital Selective Calling (DSC), such as Distress, Safety, and Ship Calls. No voice communication is allowed on CH70.

44

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

CH

SEND

RECEIVE

TRAFFIC TYPE

SHIP

SHIP

NAME TAG

 

(MHz)

(MHz)

 

TO

TO

 

 

 

 

 

SHIP

SHORE

 

01

156.050

160.650

Public Correspondence, Duplex

No

Yes

TELEPHONE

02

156.100

160.700

Public Correspondence, Duplex

No

Yes

TELEPHONE

03

156.150

160.750

Public Correspondence, Duplex

No

Yes

TELEPHONE

04A

156.200

156.200

Canadian Coast Guard, SAR

Yes

Yes

CANADIAN CG

05A

156.250

156.250

Port Operations, VTS in Selected

Yes

Yes

PORT OPS/VTS

 

 

 

Areas

 

 

 

06

156.300

156.300

Inter-ship Safety

Yes

No

SAFETY

07A

156.350

156.350

Commercial

Yes

Yes

COMMERCIAL

08

156.400

156.400

Commercial (inter-ship only)

Yes

No

COMMERCIAL

09

156.450

156.450

Recreational Calling Channel

Yes

Yes

CALLING

10

156.500

156.500

Commercial

Yes

Yes

COMMERCIAL

11

156.550

156.550

Commercial, VTS in Selected

Yes

Yes

VTS

 

 

 

Areas

 

 

 

12

156.600

156.600

Port Operations, VTS in Selected

Yes

Yes

PORT OPS/VTS

 

 

 

Areas

 

 

 

13 3

156.650

156.650

Intership Navigation Safety

Yes

No

BRIDGE COM

 

 

 

(bridge-to-bridge) 1W with power-up

 

 

 

14

156.700

156.700

Port Operations, VTS in Selected

Yes

Yes

PORT OPS/VTS

 

 

 

Areas

 

 

 

15 1

156.750

156.750

Commercial – 1W Only

Yes

Yes

COMMERCIAL

16

156.800

156.800

International Distress, Safety,

Yes

Yes

DISTRESS

 

 

 

and Calling

 

 

 

17 1

156.850

156.850

State Controlled – 1W Only

Yes

Yes

SAR

18A

156.900

156.900

Commercial

Yes

Yes

COMMERCIAL

19A

156.950

156.950

Canadian Coast Guard

Yes

Yes

CANADIAN CG

20 1

157.000

161.600

Canadian Coast Guard, Duplex–

No

Yes

CANADIAN CG

 

 

 

1W Only

 

 

 

21

157.050

161.650

Port Operations, Duplex

No

Yes

PORT OPS

21A

157.050

157.050

U.S. Government, Canadian

Yes

Yes

UNAUTHORIZED

 

 

 

Coast Guard

 

 

 

21B

RX Only

161.650

Port Operations, RX Only

------

------

PORT OPS

22A

157.100

157.100

Canadian Coast Guard Liaison

Yes

Yes

CANADIAN CG

23

157.150

161.750

Public Correspondence, Duplex

No

Yes

TELEPHONE

24

157.200

161.800

Public Correspondence, Duplex

No

Yes

TELEPHONE

25

157.250

161.850

Public Correspondence, Duplex

No

Yes

TELEPHONE

25B

RX Only

161.850

Public Correspondence, RX Only

------

------

TELEPHONE

26

157.300

161.900

Public Correspondence, Duplex

No

Yes

TELEPHONE

27

157.350

161.950

Public Correspondence, Duplex

No

Yes

TELEPHONE

28

157.400

162.000

Public Correspondence, Duplex

No

Yes

TELEPHONE

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

45

CH

SEND

RECEIVE TRAFFIC TYPE

SHIP

SHIP

NAME TAG

 

(MHz)

(MHz)

 

TO

TO

 

 

 

 

 

SHIP

SHORE

 

28B

RX Only

162.000

Public Correspondence, RX Only ------

------

TELEPHONE

60

156.025

160.625

Public Correspondence, Duplex

No

Yes

TELEPHONE

61A

156.075

156.075

U.S. Government, Canadian

Yes

Yes

UNAUTHORIZED

4Coast Guard

62A

156.125

156.125

Canadian Coast Guard

Yes

Yes

CANADIAN CG

64

156.225

160.825

Public Correspondence, Duplex

No

Yes

TELEPHONE

64A

156.225

156.225

U.S. Government, Canadian

Yes

Yes

UNAUTHORIZED

4Commercial Fishing

65A

156.275

156.275

Port Operations

Yes

Yes

PORT OPS

66A

156.325

156.325

Port Operations – 1W Only

Yes

Yes

PORT OPS

1

 

 

 

 

 

 

 

 

 

 

 

 

 

67

156.375

156.375

Commercial, SAR

Yes

No

COMMERCIAL

68

156.425

156.425

Boat Operations, Recreational

Yes

No

SHIP - SHIP

69

156.475

156.475

Commercial Fishing Only

Yes

Yes

COMMERCIAL

70 6

156.525

156.525

Digital Selective Calling - DSC

------

------

DSC

71

156.575

156.575

Boat Operations, Recreational

Yes

Yes

PLEASURE

72

156.625

156.625

Intership

Yes

No

SHIP - SHIP

73

156.675

156.675

Commercial Fishing Only

Yes

Yes

COMMERCIAL

74

156.725

156.725

Commercial Fishing Only

Yes

Yes

COMMERCIAL

77 1

156.875

156.875

Port Operations –1W Only

Yes

Yes

PORT OPS

78A

156.925

156.925

Boat Operations, Recreational

Yes

No

SHIP - SHIP

79A

156.975

156.975

Commercial

Yes

Yes

COMMERCIAL

80A

157.025

157.025

Commercial

Yes

Yes

COMMERCIAL

81A

157.075

157.075

U.S. Government Operations

Yes

Yes

UNAUTHORIZED

4

 

 

 

 

 

 

 

 

 

 

 

 

 

82A

157.125

157.125

U.S. Government, Canadian

Yes

Yes

UNAUTHORIZED

4Coast Guard

83

157.175

161.775

Canadian Coast Guard

Yes

Yes

CANADIAN CG

83A

157.175

157.175

U.S. Government, Canadian

Yes

Yes

UNAUTHORIZED

4Coast Guard

 

83B

RX Only

161.775

Canadian Coast Guard, RX Only

------

------

CANADIAN CG

84

157.225

161.825

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

 

Operator

 

 

 

85

157.275

161.875

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

 

Operator

 

 

 

86

157.325

161.925

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

 

Operator

 

 

 

87

157.375

161.975

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

 

Operator

 

 

 

88

157.425

162.025

Public Correspondence, Marine

No

Yes

TELEPHONE

 

 

 

 

Operator

 

 

 

 

46

 

 

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

WEATHER

 

MHz

TRAFFIC TYPE

 

 

NAME TAG

Wx01

RX Only

162.550

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx02

RX Only

162.400

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx03

RX Only

162.475

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx04

RX Only

162.425

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx05

RX Only

162.450

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx06

RX Only

162.500

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx07

RX Only

162.525

NOAA WEATHER CHANNEL

------

------

NOAA WX

Wx08

RX Only

161.650

CANADIAN WEATHER CHANNEL

------

------

CANADA WX

Wx09

RX Only

161.775

CANADIAN WEATHER CHANNEL

------

------

CANADA WX

Wx10

RX Only

163.275

NOAA WEATHER CHANNEL

------

------

NOAA WX

SPECIAL NOTES ON CANADA CHANNEL USAGE

1.LOW POWER (1 W) only.

2.Receive Only.

3.LOW POWER (1 W) initially. Override to HIGH POWER by holding down H/L key before transmitting. Used normally in bridge-to-bridge communications.

4.Lightly Shaded Simplex channels 21A, 23A, 61A, 64A, 81A, 82A, and 83A cannot be lawfully used in Canada waters unless special authorization is obtained from the Canadian Coast Guard. Not for use by the general public.

5.The letter “A” illuminated by the channel number indicates the Canada channel is simplex. This same channel is always duplex when selecting International. There is no “A” reference for International channels. The letter “B” is only used for some Canadian “Receive Only” channels.

6.Channel 70 is designated for use exclusively for Digital Selective Calling (DSC), such as Distress, Safety, and Ship Calls. No voice communication is allowed on CH70.

7.The CANADA mode is not legal to use in U.S. waters.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

47

CH

SEND

RECEIVE

TRAFFIC TYPE

SHIP

SHIP TO

NAME TAG

 

(MHz)

(MHz)

 

TO

SHORE

 

 

 

 

 

SHIP

 

 

01

156.050

160.650

Public Correspondence, Duplex

No

Yes

TELEPHONE

02

156.100

160.700

Public Correspondence, Duplex

No

Yes

TELEPHONE

03

156.150

160.750

Public Correspondence, Duplex

No

Yes

TELEPHONE

04

156.200

160.800

Port Operations, Duplex

No

Yes

PORT OPS

05

156.250

160.850

Port Operations, VTS in

No

Yes

PORT OPS/VTS

 

 

 

Selected Areas

 

 

 

06

156.300

156.300

Inter-ship Safety

Yes

No

SAFETY

07

156.350

160.950

Port Operations, Duplex

No

Yes

PORT OPS

08

156.400

156.400

Commercial (inter-ship only)

Yes

No

COMMERCIAL

09

156.450

156.450

Recreational Calling Channel

Yes

Yes

CALLING

10

156.500

156.500

Commercial

Yes

Yes

COMMERCIAL

11

156.550

156.550

Commercial, VTS in Selected

Yes

Yes

VTS

 

 

 

Areas

 

 

 

12

156.600

156.600

Port Operations, Selected VTS

Yes

Yes

PORT OPS/VTS

 

 

 

Areas

 

 

 

13

156.650

156.650

Intership Navigation Safety

Yes

No

BRIDGE COM

 

 

 

(bridge-to-bridge)

 

 

 

14

156.700

156.700

Port Operations, VTS in

Yes

Yes

PORT OPS/VTS

 

 

 

Selected Areas

 

 

 

15 1

156.750

156.750

Port Operations – 1W Only

Yes

Yes

PORT OPS

16

156.800

156.800

International Distress, Safety,

Yes

Yes

DISTRESS

 

 

 

and Calling

 

 

 

17 1

156.850

156.850

State Controlled – 1W Only

Yes

Yes

SAR

18

156.900

161.500

Port Operations, Duplex

No

Yes

PORT OPS

19

156.950

161.550

Commercial, Duplex

No

Yes

SHIP - SHORE

20

157.000

161.600

Port Operations, Duplex

No

Yes

PORT OPS

21

157.050

161.650

Port Operations, Duplex

No

Yes

PORT OPS

22

157.100

161.700

Port Operations, Duplex

No

Yes

PORT OPS

23

157.150

161.750

Public Correspondence, Duplex

No

Yes

TELEPHONE

24

157.200

161.800

Public Correspondence, Duplex

No

Yes

TELEPHONE

25

157.250

161.850

Public Correspondence, Duplex

No

Yes

TELEPHONE

26

157.300

161.900

Public Correspondence, Duplex

No

Yes

TELEPHONE

27

157.350

161.950

Public Correspondence, Duplex

No

Yes

TELEPHONE

28

157.400

162.000

Public Correspondence, Duplex

No

Yes

TELEPHONE

48

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

CH

SEND

RECEIVE

TRAFFIC TYPE

SHIP

SHIP TO

NAME TAG

 

(MHz)

(MHz)

 

TO

SHORE

 

 

 

 

 

 

SHIP

 

 

 

60

156.025

160.625

Public Correspondence, Duplex

No

Yes

TELEPHONE

61

156.075

160.675

Port Operations, Duplex

No

Yes

PORT OPS

62

156.125

160.725

Port Operations, Duplex

No

Yes

PORT OPS

63

156.175

160.775

Port Operations, Duplex

No

Yes

PORT OPS

64

156.225

160.825

Public Correspondence, Duplex

No

Yes

TELEPHONE

65

156.275

160.875

Port Operations, Duplex

No

Yes

PORT OPS

66

156.325

160.925

Port Operations, Duplex

No

Yes

PORT OPS

67

156.375

156.375

Commercial, bridge-to-bridge

Yes

No

BRIDGE COM

68

156.425

156.425

Boat Operations, Recreational

Yes

No

SHIP - SHIP

69

156.475

156.475

Port Operations

Yes

Yes

PORT OPS

70 3

156.525

156.525

Digital Selective Calling - DSC

------

------

 

DSC

71

156.575

156.575

Port Operations

Yes

Yes

PORT OPS

72

156.625

156.625

Intership

Yes

No

SHIP - SHIP

73

156.675

156.675

Port Operations

Yes

Yes

PORT OPS

74

156.725

156.725

Port Operations

Yes

Yes

PORT OPS

77

156.875

156.875

Intership

Yes

No

SHIP - SHIP

78

156.925

161.525

Non-Commercial, Duplex

No

Yes

SHIP - SHORE

79

156.975

161.575

Commercial, Duplex

No

Yes

SHIP - SHORE

80

157.025

161.625

Commercial, Duplex

No

Yes

SHIP - SHORE

81

157.075

161.675

Port Operations, Duplex

No

Yes

PORT OPS

82

157.125

161.725

Port Operations, Duplex

No

Yes

PORT OPS

83

157.175

161.775

Public Correspondence, Duplex

No

Yes

TELEPHONE

84

157.225

161.825

Public Correspondence, Duplex

No

Yes

TELEPHONE

85

157.275

161.875

Public Correspondence, Duplex

No

Yes

TELEPHONE

86

157.325

161.925

Public Correspondence, Duplex

No

Yes

TELEPHONE

87

157.375

157.357

Intership

Yes

No

SHIP - SHIP

88

157.425

157.425

Intership

Yes

No

SHIP - SHIP

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

49

CH

SEND

RECEIVE

TRAFFIC TYPE

SHIP

SHIP

NAME TAG

 

(MHz)

(MHz)

 

TO

TO

 

 

 

 

 

SHIP

SHORE

 

00 6

156.000

156.000

UK Coast Guard Users

Yes

Yes

UK COAST GRD

M1

157.425

157.850

UK Marina Channel M1

Yes

Yes

UK MARINA

M2

161.425

161.425

UK Marina Channel M2

Yes

Yes

UK MARINA

31

157.550

162.150

INT’L, Duplex (Holland)

No

Yes

NL MARINA

96H

162.425

162.425

INT’L (Belgium)

No

Yes

BEL G MARINA

L1

155.500

155.500

INT’L (Scandinavia)

Yes

no

LEISURE 1

L2

155.525

155.525

INT’L (Scandinavia)

Yes

no

LEISURE 2

L3

155.650

155.650

INT’L (Scandinavia – not in

Yes

no

LE ISURE3

 

 

 

Denmark)

 

 

 

F1

155.625

155.625

INT’L (Scandinavia)

Yes

no

FISHING 1

F2

155.775

155.775

INT’L (Scandinavia)

Yes

no

FISHING 2

F3

155.825

155.825

INT’L (Scandinavia) call back

Yes

no

FISHING 3

AIS1

161.975

161.975

AIS1

-----

-----

-----

AIS2

162.025

162.025

AIS2

-----

-----

-----

SPECIAL NOTES ON EUROPEAN INTERNATIONAL CHANNEL USAGE

1.LOW POWER (1 W) only.

2.LOW POWER (1 W) initially. Override to HIGH POWER by holding down H/L key before transmitting. Used normally in bridge-to-bridge communications.

3.Channel 70 is designated for use exclusively for Digital Selective Calling (DSC), such as Distress, Safety, and Ship Calls. No voice communication is allowed on CH70.

4.The INTERNATIONAL mode is not legal for use in U.S.A. or Canada waters.

5.No WX channels are available.

6.Lightly Shaded Simplex channel CH00 is only available in the UK to Coast Guard users with written authorization.

7.The special channels above maybe fitted to your radio. These are only licensed for use in the country indicated. No attempt should be made to use them in any other country.

50

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual

Appendix D - MMSID and License Information

VHF 7100 only

You must obtain a user MMSID (Marine Mobile Service Identity) and enter it into your 7100 in order to use the DSC functions. Contact the appropriate authorities in your country. If you are unsure who to contact, consult your Navman dealer.

The user MMSID is a unique nine digit number, similar to a personal telephone number. It is used on marine transceivers that are capable of using DSC (Digital Select Calling).

Depending upon your location, you may need a radio station license for the VHF 7100. You may also need an individual operator’s license.

Navman NZ recommends that you check the requirements of your national radio communications authorities before operating DSC functions.

VHF 7000, 7100US, 7100EU Operation Manual

NAVMAN

51

Appendix E - How to Contact Us

www.navman.com

NORTH AMERICA

Navman USA Inc.

30 Sudbury Rd, Acton, MA 01720. Toll Free: +1 866 628 6261 Fax: +1 978 897 8264

e-mail: sales@navmanusa.com web:www.navman.com

AUSTRALIA

Navman Australia Pty. Limited Unit 2 / 5-13 Parsons St. Rozelle, NSW 2039, Australia. Ph: +61 2 9818 8382 Fax: +61 2 9818 8386

e-mail: sales@navman.com.au web: www.navman.com

OCEANIA

New Zealand

Absolute Marine Ltd.

Unit B, 138 Harris Road,

East Tamaki, Auckland.

Ph: +64 9 273 9273

Fax: +64 9 273 9099

e-mail:navman@absolutemarine.co.nz

Papua New Guinea

Lohberger Engineering,

Lawes Road, Konedobu.

PO Box 810, Port Moresby. Ph: +675 321 2122 Fax: +675 321 2704

e-mail: loheng@online.net.pg web: www.lohberger.com.pg

SOUTH AMERICA Argentina

Costanera Uno S.A.

Av Pte Ramón S. Castillo y Calle 13 Zip 1425 Buenos Aires, Argentina. Ph: +54 11 4312 4545

Fax +54 11 4312 5258 e-mail:

purchase@costanerauno.com.ar web: www.costanerauno.ar

Brazil

Equinautic Com Imp Exp de Equip Nauticos Ltda.

Rua Ernesto Paiva, 139 Clube dos Jangadeiros Porto Alegre - RS - Brasil CEP: 91900-200.

Ph: +55 51 3268 6675 +55 51 3269 2975 Fax: +55 51 3268 1034

e-mail:

equinautic@equinautic.com.br web: www.equinautic.com.br

Realmarine

Estrada do Joa 3862,

Barra da Tijuca, Rio de Janeiro, Brazil. CEP: 22611-020.

Ph: +55 21 2483 9700

Fax: +55 21 2495 6823 e-mail: tito@realmarine.com.br web: www.realmarine.com.br

Chile

Equimar

Manuel Rodrigurez 27 Santiago, Chile.

Ph: +56 2 698 0055

Fax +56 2 698 3765

e-mail: mmontecinos@equimar.cl

Mera Vennik

Colon 1148, Talcahuano, 4262798, Chile.

Ph: +56 41 541 752

Fax +56 41 543 489

e-mail: meravennik@entel.chile.net

52

CENTRAL AMERICA Mexico

Mercury Marine de Mexico Anastacio Bustamente #76

Interior 6 Colonia Francisco Zarabia, Zapapan, Jalisco, C.P. 45236 Mexico. Ph: +52 33 3283 1030

Fax: +52 33 3283 1034 web: www.equinautic.com.br

ASIA

China

Peaceful Marine Electronics Co. Ltd. Guangzhou, Hong Kong, Dalian, Qingdao, Shanghai

1701 Yanjiang Building

195 Yan Jiang Zhong Rd. 510115 Guangzhou, China.

Ph: +86 20 3869 8839

Fax: +86 20 3869 8780

e-mail: sales@peaceful-marine.com web: www.peaceful-marine.com

India

Access India Overseas Pvt. Ltd. A-98, Sector 21,

Noida - 201 301, India.

Ph: +91 120 244 2697

TeleFax: +91 120 253 7881

Mobile: +91 98115 04557 e-mail: vkapil@del3.vsnl.net.in

Esmario Export Enterprises

Block No. F-1, 3rd Floor, Surya Towers Sardar Patel Rd, Secunderbad 500 003. Ph: +91 40 2784 5163

Fax: +91 40 2784 0595 e-mail: gjfeee@hd1.vsnl.net.in web: www.esmario.com

Indonesia

Polytech Nusantara, Graha Paramita 2nd Floor, Jln Denpasar Raya Blok D2

Kav 8 Kuningan, Jakarta 12940. Ph: +62 21 252 3249

Fax: +62 21 252 3250

e-mail: polytech@transavia.co.id

Korea

Kumhomarine Technology Co. Ltd. #604-842,2F,1118-15,Janglim1-Dong, Saha-Gu, Busan, Korea.

Ph: +82 51 293 8589

Fax: +82 51 265 8984

e-mail: info@kumhomarine.com web: www.kumhomarine.com

Maldives

Maizan Electronics Pte. Ltd.

Henveyru, 08 Sosunmagu. Male', Maldives.

Mobile: +960 78 24 44

Ph: +960 32 32 11

Fax: +960 32 57 07

e-mail: ahmed@maizan.com.mv

Singapore, Malaysia, Brunei, Indonesia and Phillipines

RIQ PTE Ltd.

Blk 3007, 81 Ubi Road 1, #02-440, Singapore 408701.

Ph: +65 6741 3723

Fax : +65 6741 3746 e-mail: riq@postone.com

Taiwan

Seafirst International Corporation No. 281, Hou-An Road, Chien-Chen Dist. Kaohsiung, Taiwan R.O.C.

Ph: +886 7 831 2688

Fax: +886 7 831 5001 e-mail: seafirst@seed.net.tw web: www.seafirst.com.tw

Thailand

Thong Electronics (Thailand) Co. Ltd. 923/588 Ta Prong Road, Mahachai, Muang, Samutsakhon 74000, Thailand. Ph: +66 34 411 919

Fax: +66 34 422 919

e-mail: sales@thongelectronics.com admins@thongelectronics.com

web: www.thongelectronics.com

Vietnam

Haidang Co. Ltd.

1763 Le Hong Phong St. Ward 12 District 10, Ho Chi Minh City. Ph: +84 8 863 2159

Fax: +84 8 863 2124 e-mail: sales@haidangvn.com web: www.haidangvn.com

MIDDLE EAST

Lebanon and Syria

Balco Stores

Balco Building, Moutran Street, Tripoli (via Beirut). - Lebanon P.O. Box: 622.

Ph: +961 6 624 512

Fax: +961 6 628 211 e-mail: balco@cyberia.net.lb

United Arab Emirates Kuwait, Oman, Iran, Saudi Arabia, Bahrain & Qatar

Abdullah Moh’d Ibrahim Trading, opp Creak Rd. Baniyas Road, Dubai. Ph: +971 4 229 1195

Fax: +971 4 229 1198 e-mail: sales@amitdubai.com

AFRICA South Africa

Pertec (Pty) Ltd (Coastal Division) 16 Paarden Eiland Road. Paarden Eiland, 7405

PO Box 527, Paarden Eiland, 7420

Cape Town, South Africa.

Ph: +27 21 511 5055

Fax: +27 21 511 5022 e-mail: info@kfa.co.za web: www.pertec.co.za

EUROPE

France, Belgium and Switzerland

Plastimo SA

15, rue Ingénieur Verrière, BP435,

56325 Lorient Cedex.

Ph: +33 2 97 87 36 36

Fax: +33 2 97 87 36 49 e-mail: plastimo@plastimo.fr web: www.plastimo.fr

Germany

Navimo Deutschland

15, rue Ingénieur Verrière BP43556325 Lorient Cedex. Ph: +49 6105 92 10 09 +49 6105 92 10 10

+49 6105 92 10 12 Fax: +49 6105 92 10 11 e-mail:

plastimo.international@plastimo.fr website: www.plastimo.de

Italy

Navimo Italia

Nuova Rade spa, Via del Pontasso 5 16015 Casella Scrivia (GE).

Ph: +39 1096 80162

Fax: +39 1096 80150 e-mail: info@nuovarade.com web: www.plastimo.it

Holland

Navimo Holland

Industrieweg 4, 2871 JE Schoonhoven.

Ph: +31 182 320 522

Fax: +31 182 320 519 e-mail: info@plastimo.nl web: www.plastimo.nl

United Kingdom

Navimo UK

Hamilton Business Park

Bailey Road, Hedge End Southhampton, Hants S030 2HE. Ph: +44 01489 778 850

Fax: +44 0870 751 1950 e-mail: sales@plastimo.co.uk

web: www.plastimo.co.uk

Sweden, Denmark, Finland and Norway

Navimo Nordic

Lundenvägen 2,

473 21 Henån.

Ph: +46 304 360 60

Fax: +46 304 307 43 e-mail: info@plastimo.se web: www.plastimo.se

Spain

Navimo España

Avenida Narcís Monturiol, 17 08339 Vilassar de Dalt, Barcelona.

Ph: +34 93 750 75 04

Fax: +34 93 750 75 34 e-mail: plastimo@plastimo.es web: www.plastimo.es

Portugal

Navimo Portugal Avenida de India N°40 1300-299 Lisbon.

Ph: +351 21 362 04 57

Fax: +351 21 362 29 08

e-mail: plastimo@siroco-nautica.pt web: www.plastimo.com

Other countries in Europe

Plastimo International

15, rue Ingénieur Verrière BP435 56325 Lorient Cedex, France. Ph: +33 2 97 87 36 59

Fax: +33 2 97 87 36 29 e-mail:

plastimo.international@plastimo.fr web: www.plastimo.com

REST OF WORLD/

MANUFACTURERS

Navman NZ Limited

13-17 Kawana St. Northcote.

P.O. Box 68 155, Newton, Auckland,

New Zealand.

Ph: +64 9 481 0500

Fax: +64 9 481 0590

e-mail: marine.sales@navman.com web: www.navman.com

Designed in New Zealand

Made in China

MN000250A

NAVMAN

VHF 7000, 7100US, 7100EU Operation Manual