O W N E R S M A N U A L S u p e r L i n e
E N G L I S H D E U T S C H F R A N Ç A I S I T A L I A N 0
Introduction
Naim Audio products are conceived with performance as the top priority. Careful installation will help ensure that their full potential is achieved. This manual covers the SuperLine phono amplifier. It begins with some general installation notes. Product specific information begins in Section 3.
1 Connections
It is important for both safety and performance that any standard cables supplied with Naim Audio products are not modified.
1.1 Interconnect Cables
Interconnect plugs and sockets should be kept clean and free from corrosion. The easiest way to clean them is to switch off the equipment, pull the plugs out of their sockets, and push them back in again. Contact cleaners and “enhancers” should not be used as the film they deposit may degrade the sound.
2.4 Radio Interference
In some circumstances, depending on where you live and the earthing arrangements in your home, you may experience radio frequency interference. Controls on broadcasting in some territories allow very high levels of radio frequency radiation and both the choice and exact siting of equipment may be critical. Susceptibility to radio frequency interference is related to the wide internal bandwidth necessary for high sound quality. A radio frequency filter kit is available for some Naim equipment but sound quality will be progressively compromised as more elements of the kit are fitted. In situations of extreme radio interference Naim equipment may be unsuitable.
2 General Installation
Naim equipment is designed to offer the finest performance possible avoiding compromise wherever practical. This can lead to circumstances that may be unfamiliar. The notes that follow contain advice specifically related to Naim equipment as well as more general warnings about the use of domestic audio products. Please read them carefully.
2.1 Siting The Equipment
In order to reduce the risk of hum audible from the loudspeakers, power supplies and power amplifiers should be located a reasonable distance away from other equipment. The maximum separation distance for connected equipment is that allowed by the standard interconnect lead.
2.2 Switching On
Source components and power supplies should be switched on before power amplifiers. Always switch amplifiers off and wait a minute before connecting or disconnecting any leads. Always use the power switch on the product rather than a mains outlet switch.
2.3 Running In
Naim equipment takes a considerable time to run in before it performs at its best. The duration varies, but under some conditions the sound may continue to improve for over a month. Better and more consistent performance will be achieved if the system is left switched on for long periods. It is worth remembering however that equipment left connected to the mains can be damaged by lightning.
2.5 Lightning Precautions
Your Naim hi-fi system can be damaged by lightning and should be turned off and disconnected from the mains when there is risk of lightning strike.
2.6 Problems?
Consumer protection varies from country to country. In most territories a retailer must be prepared to take back any equipment he has sold if it cannot be made to work satisfactorily. A problem may be due to a fault in the system or its installation so it is essential to make full use of your dealer’s diagnostic skills. Please contact your local distributor, or Naim Audio directly, if any difficulties cannot be resolved.
Some Naim equipment is made in special versions for different territories and this makes it impracticable to arrange international guarantees. Please establish the local guarantee arrangements with your retailer. Contact Naim Audio directly for help and advice if necessary.
2.7 Service and Updates
It is essential that repairs and updates are only carried out by an authorised Naim retailer or at the factory by Naim itself. Many components are custom made, tested or matched and appropriate replacements are often unobtainable from other sources.
Direct contact to Naim for service or update information should be made initially through Customer Services:
Tel: +44 (0)1722 426600
Email: info@naimaudio.com
Please quote the product serial number (found on its rear panel) in all correspondence.
SuperLine Installation
3 SuperLine Installation
The SuperLine moving coil phono amplifier is designed to extract the best possible musical performance from vinyl disc replay. It should be mounted horizontally on an equipment stand intended for the purpose. It is important to ensure that it is level.
The SuperLine contains no internal power supply and must be connected either to a Naim amplifier incorporating an appropriate power supply output, or to a dedicated Naim power supply. SuperLine output is muted for 2 minutes following switch-on to allow its circuitry to reach optimal status.
Cartridge loading resistance and capacitance can be adjusted by inserting combinations of resistive and capacitive “load plugs” into sockets on the SuperLine rear panel.
The SuperLine incorporates a suspension system to isolate its sensitive components from vibrational energy. The suspension system is protected during shipping by two transit screws. The transit screws must be removed before use. Once the transit screws are removed the SuperLine must not be inverted. Transit screw removal is best carried out once the SuperLine is installed in its final location and all connections are made.
3.1 Transit Screws
Two transit screws must be removed from the underside of the SuperLine before use and replaced if it is to be carried any distance, packed or shipped. Transit screw removal is illustrated in Diagram 3.2. SuperLine transit screws must not be used with any other Naim product.
Damage may result if the SuperLine is inverted either during or after transit screw removal.
To gain access to the transit screws, position one end of the SuperLine over the edge of a table, remove (or replace) the screw that becomes accessible and then repeat with the other end.
3.2 Transit Screw Removal
front transit screw
rear transit screw
3.3 Connecting SuperLine
3.3.1 Power Supply
The SuperLine must be connected to a dedicated Supercap, Hi-Cap or Flatcap power supply (option one) or a Naim preamplifier or integrated amplifier that
incorporates an appropriate power supply output (option two).
If option one is chosen, connect the SuperLine to the dedicated power supply using, in the case of a Hi-Cap or Flatcap, a Naim SNAIC interconnect cable, and in the case of a Supercap, the appropriate Naim Burndy cable.
In either case take care to connect with the correct cable orientation.
If option two is chosen, connect the SuperLine to the preamplifier or integrated amplifier’s 5 pin DIN aux input/ power output socket using a Naim SNAIC interconnect cable. Take care to connect with the correct cable orientation.
Note: If the SuperLine’s Burndy power supply socket is not used the supplied Burndy link plug must be inserted. Similarly, if the SuperLine’s DIN power supply socket is not used the supplied dust cover should be fitted.
3.3.2 Signal Input
Connect the output cable of the pick-up arm to either the BNC or phono input sockets. Only one option, phono or BNC, should be connected at any time. Take care to ensure that the left and right channels are connected to the appropriate sockets.
Connect the pick-up arm earth lead to the rear panel ground terminal.
3.3.3 Signal Output
The SuperLine output signal is carried on the power supply cable either directly to the preamplifier or via an optional power supply.
1
SuperLine Installation
3.4 Cartridge Loading
The resistive and capacitive input load presented by the SuperLine to the pick-up cartridge can be adjusted by inserting a combination of “load plugs” into the appropriate sockets in the rear panel.
The appropriate load plug combination will depend on both the manufacturer’s recommendations for the pick-up cartridge in use and subjective preference.
Each load plug is constructed from a 5-pin DIN plug that contains the appropriate passive components. A label on each load plug identifies its load value.
Seven standard load plugs are supplied - four resistive and three capacitive - to provide 20 combinations
(including the default input loads applied when no load plugs are inserted). Table 3.5 lists the standard load plug combinations.
Note: In addition to the standard load plugs supplied, 470Ω and 560Ω resistive plugs are also available on request.
Other values may also be created either by modifying standard plugs or manufacturing new ones. Contact your retailer or local distributor for more information.
Always ensure that resistive and capacitive load plugs are inserted in the correct socket.
Note: The SuperLine incorporates 10kΩ resistance and
100pF (0.1nF) capacitance loads internally. With no load plugs fitted these values constitute the default load.
3.5 Cartridge Load Plug Combinations
Resistance |
Capacitance |
Comments |
10kΩ |
100pF |
Internal load only. No plugs fitted. |
10kΩ |
1nF |
No resistive plug fitted. |
10kΩ |
5.6nF |
No resistive plug fitted. |
10kΩ |
10nF |
No resistive plug fitted. |
1kΩ |
100pF |
No capacitive plug fitted. |
1kΩ |
1nF |
|
1kΩ |
5.6nF |
|
1kΩ |
10nF |
|
500Ω |
100pF |
No capacitive plug fitted. |
500Ω |
1nF |
Note 1 |
Note 1: Approximates to a Naim ‘K’ load (560Ω and 1nF).
Resistance |
Capacitance |
Comments |
500Ω |
5.6nF |
Note 2. |
500Ω |
10nF |
|
220Ω |
100pF |
No capacitive plug fitted. |
220Ω |
1nF |
|
220Ω |
5.6nF |
|
220Ω |
10nF |
|
100Ω |
100pF |
No capacitive plug fitted. |
100Ω |
1nF |
|
100Ω |
5.6nF |
|
100Ω |
10nF |
|
Note 2: Approximates to a Naim ‘S’ load (470Ω and 6.8nF).
4 SuperLine Connections
4.1 SuperLine Rear
|
|
|
BNC input |
|
phono input |
|
|||
|
|
|
sockets. Ch. |
|
to Supercap |
||||
pick-up arm |
|
1 - left, Ch. 2 |
|
sockets. Ch. 1 |
|||||
ground |
|
- right |
|
- left, Ch. 2 - right |
power supply |
||||
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note: SuperLine output is muted for 2 minutes following switch-on to
allow its circuitry to reach optimal status.
resistive |
capacitive |
|
toamplifierpower |
|
|||
load plug |
load plug |
|
supply output or to |
socket |
socket |
|
Hi-Cap or Flatcap |
|
|
|
power supply |
2
SuperLine Connections
4.2 SuperLine connected to Supernait
link plug fitted
cable direction marker
power mains input and fuse
4.3 SuperLine connected to NAC 122x and Flatcap 2x
cable
link plug direction fitted marker
Interconnect Cables
240° 5 to 5 pin DIN
Interconnect Cables
240° 5 to 5 pin DIN
4 pin to 5 pin DIN (or 4 to 5 pin Hi-Line)
power mains input and fuse
3
SuperLine Connections
4.4 SuperLine connected to Hi-Cap
cable
direction link plug marker fitted
Interconnect Cables
240° 5 to 5 pin DIN
4 pin to 5 pin DIN (or 4 to 5 pin Hi-Line)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
mains input |
topreamplifier |
|
|
|
|
|
and fuse |
input |
|
|
4.5 SuperLine connected to Supercap
cable direction marker
dust cover fitted
Interconnect Cables
SuperLine Burndy
4 pin to 5 pin DIN (or 4 to 5 pin Hi-Line)
mains input |
|
|
|
|
|
|
|
|
|
|
|
topreamplifier |
|
|
|
and fuse |
input |
|
|
4
SuperLine Specifications
5 SuperLine Specification
5.1 Standard Model
Cartridge compatibility |
100µV to 500µV |
Gain |
64dB @ 1kHz |
Signal to Noise |
82dB ref 500µV input, 0 Ohms (A-weighted) |
Distortion |
<0.005% (500µV @1kHz) |
Frequency response |
10Hz to >200kHz -3dB |
RIAA accuracy + 10Hz HPF |
+/-0.1dB (20Hz to 20kHz) |
Crosstalk |
>80dB (20Hz to 20kHz) |
Max output |
7.5VRMS (21Vpkpk) |
Input overload |
5mVrms (1kHz) |
Weight |
7.7kg |
Input load options |
1kΩ, 500Ω, 220Ω, 100Ω (resistive) |
|
1nF, 5.6nF, 10nF (capacitive) |
Dimensions |
87 x 207 x 314mm |
5.2 Low Gain Model (E version)
Cartridge compatibility |
200µV to 1mV |
Gain |
58dB @ 1kHz |
Signal to Noise |
78dB ref 500µV input, 0 Ohms (A-weighted) |
Distortion |
<0.005% (500µV @1kHz) |
Frequency response |
10Hz to >200kHz -3dB |
RIAA accuracy + 10Hz HPF |
+/-0.1dB (20Hz to 20kHz) |
Crosstalk |
>80dB (20Hz to 20kHz) |
Max output |
7.5VRMS (21Vpkpk) |
Input overload |
10mVrms (1kHz) |
Weight |
7.7kg |
Input load options |
1kΩ, 500Ω, 220Ω, 100Ω (resistive) |
|
1nF, 5.6nF, 10nF (capacitive) |
Dimensions |
87 x 207 x 314mm |
5
6
B E D I E N U N G S A N L E I T U N G S u p e r L i n e
E N G L I S H D E U T S C H F R A N Ç A I S I T A L I A N 0
Einleitung
Bei der Entwicklung von Naim-Audio-Produkten hat die Klangqualität stets oberste Priorität, und eine sorgfältig durchgeführte Installation gewährleistet, dass das Potenzial der Produkte ausgeschöpft wird. Diese Bedienungsanleitung enthält Informationen zur Phono-Vorstufe SuperLine. Die ersten Abschnitte enthalten Allgemeines zur Installation. Produktspezifische Informationen finden Sie ab Abschnitt 3.
1 Anschlüsse
Zur Gewährleistung der Sicherheit und der höchstmöglichen Klangqualität sollten die Standardanschlusskabel nicht modifiziert werden.
Stecker und Buchsen sollten sauber und frei von Schmutz und Korrosion sein. Am einfachsten sind sie zu reinigen, indem Sie die Anlage ausschalten, die Stecker aus den Buchsen ziehen und sie dann wieder einstecken. Verwenden Sie keine Kontaktreiniger, da diese oft einen dünnen Film hinterlassen, der die Klangqualität beeinträchtigen kann.
2.4 Störungen durch Funkwellen
Unter Umständen können aufgrund von Funkwellen Störungen auftreten, je nachdem, wo Sie wohnen und wie die Erdung in Ihrem Haus ausgeführt ist. In manchen Ländern lassen die Fernmeldegesetze starke Hochfrequenzstrahlung zu, und sowohl der genaue Standort Ihrer Anlage als
auch die Wahl der Geräte kann entscheidend sein. Diese
Störungen hängen oft mit der großen Signalbandbreite von Hifi-Geräten zusammen. Für einige Naim-Geräte ist ein Entstörsatz erhältlich, der jedoch Abstriche an der
Klangqualität mit sich bringt. Bei extremen Störungen können sich Naim-Geräte als ungeeignet erweisen.
2 Allgemeine Hinweise
Naim-Audio-Produkte werden mit dem Ziel entwickelt, höchste Klangqualität zu bieten. Kompromisse werden so weit wie möglich vermieden, was ungewohnte Betriebsbedingungen zur Folge haben kann. Dieser Abschnitt enthält sowohl Naim-spezifische Informationen als auch allgemeine Warnhinweise zum Gebrauch von Hifi-Geräten. Bitte lesen Sie die Hinweise sorgfältig.
2.1 Platzieren der Geräte
Netzteile und Endstufen mit integrierten Netzteilen sollten in angemessenem Abstand von den anderen
Komponenten aufgestellt werden, damit die Magnetfelder der Transformatoren kein über die Lautsprecher hörbares Brummen verursachen. Die Länge der mitgelieferten
Signalkabel entspricht dem maximalen Abstand zwischen den Komponenten.
2.2 Einund Ausschalten
Quellgeräte und Vorstufe sollten immer vor den Endstufen eingeschaltet werden. Schalten Sie, bevor Sie an Ihrer
Anlage Kabel stecken oder ziehen, grundsätzlich sämtliche Verstärker aus und warten Sie etwa eine Minute.
Verwenden Sie zum Einund Ausschalten stets den Netzschalter an den Geräten.
2.3 Einspielen
Naim-Geräte benötigen einige Zeit, bevor sie „eingespielt“ sind und ihr klangliches Höchstniveau erreichen. Diese Phase dauert unterschiedlich lange; unter Umständen kann sich die Klangqualität über einen
Zeitraum von mehr als einem Monat hinweg steigern.
Bessere und gleichmäßigere Qualität lässt sich erreichen, wenn Sie die Geräte längere Zeit eingeschaltet lassen. Beachten Sie jedoch, dass alle elektronischen Geräte durch Blitzschlag beschädigt werden können.
2.5 Blitzschlag
Ihre Naim-Geräte können durch Blitzschlag beschädigt werden und sollten deshalb während eines Gewitters ausgeschaltet werden. Um die Geräte komplett zu schützen, sollten alle Netzstecker und Antennen ausgesteckt werden.
2.6 Bei Problemen
Verbraucherschutzgesetze sind von Land zu Land verschieden. In den meisten Ländern muss der Händler Produkte zurücknehmen, wenn sie nicht zu Ihrer Zufriedenheit installiert werden können. Probleme können sich aus Fehlern an den Produkten oder beim Installieren ergeben; es ist
daher sinnvoll, den Sachverstand des zuständigen Händlers vor Ort zu nutzen. Sollten etwaige Probleme nicht gelöst werden können, wenden Sie sich bitte an die zuständige
Vertriebsgesellschaft oder an Naim Audio.
Manche Naim-Produkte werden für einzelne
Länder in Sonderausführungen hergestellt, weshalb
Garantiebedingungen von Land zu Land verschieden sind. Vergewissern Sie sich beim Kauf der Produkte, welche
Garantiebedingungen für Sie gelten. Falls Sie Rat oder Hilfe benötigen, können Sie sich auch direkt mit Naim Audio in
Verbindung setzen.
2.7 Reparaturen und Updates
Reparaturen und Updates sollten ausschließlich von einem anerkannten Naim-Händler, der zuständigen
Vertriebsgesellschaft oder Naim Audio durchgeführt werden. Viele Bauteile werden speziell für Naim Audio hergestellt, geprüft oder abgeglichen, weshalb geeignete
Ersatzteile oft nur über Naim erhältlich sind.
Wenn Sie Fragen zum Kundendienst oder zu Updates haben und Naim Audio direkt kontaktieren möchten, wenden Sie sich bitte an unsere Kundendienstabteilung:
Telefon: +44 (0)1722 426600 Email: info@naimaudio.com
Bitte geben Sie bei E-Mail-Anfragen stets die Seriennummer an, die auf der Rückseite Ihres Naim-Geräts steht.