NAD 7600 User Manual

7600

Stereo Receiver

Date of manufacture : Jan 87 - Jun 90

Please note that this document contains the text from the original product brochure, and some technical statements may now be out of date

The NAD 7600 is one of the world’s most powerful, most sensitive, and most flexible stereo receivers. It
consists of NAD’s three finest Monitor Series stereo separates 11300 Preamplifier, 4300 Tuner, and
2600A Power Amplifier), combined on a single chassis and operated by infrared remote control.

The 7600 is rated at 150 watts/channel for continuous test tones, but its Power Envelope circuitry
produces much higher levels of tone-burst power for music. Even with compressed recordings of rock
music in which the peaks are only a few dB higher than the aver-age power, the 7600 maintains a
clipping level above 500 watts per channel into the complex 4-ohm impedance that is typical of real
loudspeakers. In bridged mode a 7600 matched with a 2600A will deliver nearly 3000 watts of dynamic
power into a pair of such speakers. The FET-input MM phono stage, employing eight selected low-noise
transistors per channel, combines superb sound-stage imaging and detail with superior rejection of
digital and radio-frequency interference. A separate class-A pre-preamplifier furnishes exquisitely quiet,
wide-range moving-coil playback. The line-level circuits in the 7600, including its feedback-operated
volume control, have a 118dB signal/noise ratio that preserves all the delicacy and purity of low-level
musical information. Bass EQ and semi-parametric tone controls provide flexible sonic tailoring to
compensate for differences in recordings, speakers, and listening rooms.

The tuner section of the 7600 shares the unique ultra-sensitive front end of the 4300. Together with
NAD’s FM NR noise-reduction system, it provides exceptionally clear and quiet reception of weak signals.
Whether you use the convenient rotary knob, the 16 presets, or the remote control for tuning, you are
assured of crystal-controlled digital accuracy.

Combining convenience with superbly musical performance, the NAD 7600 is a no-holds-barred product
that establishes new standards in receiver design.

PRE-AMP SECTION

Phono input

Input impedance (R and C) MM 47kΩ / 120pF

MC 47kΩ / 120pF

Input sensitivity, 1kHz MM 0.28mV ref. 1W

MC 0.02mV ref. 1W

Signal/Noise ratio (A-weighted with cartridge connected) MM 76dB ref. 5mV

MC 76dB ref. 5mV
THD (20Hz - 20kHz) <0.04%
RIAA response accuracy (20Hz - 20kHz) ±0.5dB

Line level inputs

Input impedance (R and C) 50kΩ / 250pF
Input sensitivity (ref. 1W) 15mV
Maximum input signal >10V
Signal/Noise ratio (A-weighted ref 1W) 96dB
Frequency response (20Hz - 20kHz) ±0.3dB

Line level outputs

Output impedance Pre-amp 600Ω

Tape Source Z + 1kΩ

Maximum output level >10V

Tone controls

Treble ±12dB at 3, 6 or 12kHz
Bass ±12dB at 50, 120 or 250Hz
Bass EQ +3dB at 60Hz

+6dB at 36Hz

Infrasonic filter (Switchable) -3dB at 14Hz, 12dB / octave

POWER AMP SECTION

Continuous output power into 8Ω * 150W (21.7dBW)
Rated distortion (THD 20Hz - 20kHz) 0.03%
Clipping power (maximum continuous power per channel) 170W
IHF Dynamic headroom at 8Ω +4dB
IHF dynamic power (maximum short term power per channel) 8Ω 400W (26dBW)

4Ω 600W (28dBW)
2Ω 800W (29dBW)

Damping factor (ref. 8Ω, 50Hz) >120
Input impedance 30kΩ / 1500pF
Input sensitivity (for rated power into 8Ω) 1V
Frequency response 3Hz - 80kHz +0, -3dB
Signal/noise ratio ref. 1W 100dB

ref. rated power 122dB

THD (20Hz - 20kHz) <0.03%

Bridged Mode

Continuous output power into 8Ω * 400W (26dBW)
IHF Dynamic headroom at 8Ω +5dB
IHF dynamic power (maximum short term power per channel) 8Ω 1.2kW (31dBW)

4Ω 1.4kW (31.5dBW)

© NAD Electronics. All rights reserved. E & OE