Page 1
Motorola
iDEN®
Digital Multi-Service Phon e
r750plus User’s Guide
11/17/00
@NTN9333A@
NTN9333-A
Page 2
Page 3
Table of Contents
Table of Contents
Table of Contents..................................................... ........................... iii
Welcome ............................................................................................... 1
TTY Access................................. .... ... ............................................................ 2
Large-Print Manuals....................................................................................... 2
Features of your r750plus Phone.................................................................... 2
Attaching and Charging the Battery............................................................... 4
Attaching the Battery.............................................................................. 4
Detaching the Battery................................. ............................................. 4
Charging the Battery............................................................................... 4
Battery and Charging Status.................................................................... 4
Turning On Your r750plus Phone.................................................................. 5
Turning Off your r750plus Phone ..................................................................5
Connecting the Supplied Antenna........................................................... 6
Keypad Lock.................................................................................................. 6
Activating Keypad Lock................................................................ .... ... .. 6
Receiving Incoming Calls....................................................................... 6
Receiving New Mail Messages............................................................... 7
Receiving Voice Mail ..............................................................................7
Receiving Private (Two-Way Radio) Calls............................................. 7
Deactivating Keypad Lock...................................................................... 7
Display Icons.................................................................................................. 8
About Modes and Menus ............................................................................... 9
Setting the Time and Date............................. ................................................. 9
Changing the Display Language .................................................................. 11
Selectable Backlight Timer .......................................................................... 11
Making Phone Calls .......................................................................... 12
Using Other Dialing Methods ...................................................................... 12
Scroll..................................................................................................... 12
Speed Dial............................................................................................. 12
Automatic Redial.............. .... .... ............................................................. 13
Last Number Redial.............................................................................. 13
Turbo Dial® Key................................................................................... 13
Plus Dialing........................................................................................... 14
Hands-Free Speakerphone..................................................................... 14
Receiving a Phone Call............................................................................... 14
Ending a Phone Call .......................... .... .... ...................................................14
What Is My Phone Number?........................................................................ 15
iii
Page 4
VibraCall® Alert ......................................................................................... 15
Selecting VibraCall Alert for All Incoming Calls and Messages......... 15
Selecting VibraCall Alert for Individual Services................................ 16
Setting the Ringer Volume .......................................................................... 16
Setting a Ring Style for the Alternate Line..................................... 16
Additional Phone Services................................................................ 17
Call Waiting................... ... .... .............................................................. ......... 17
Turning Off Call Waiting..................................................................... 17
Call Hold............................................................................................... 17
3-Way Calling....................................................................................... 18
Alternate Phone Line ................................................................................... 18
Setting the Active Line......................................................................... 18
Receiving a Call.................................................................................... 19
Receiving a Call on Your Alternate Line............................................. 19
Receiving a Phone Call Using Speakerphone ...................................... 19
Missed Call Indicator................................................................................... 19
Call Forwarding ...........................................................................................20
Unconditional Call Forwarding............................................................ 20
Conditional Call Forwarding................................................................ 20
Creating, Editing, and Using Stored Lists....................................... 22
Combined Phone Number and Private ID List..................................... 22
Entering Numbers............................................................................ 22
Entering Names............................................................................... 22
Storing Names and Numbers........................................................... 23
Pause Digit Entry............................................................................. 24
Editing and Erasing Phone List Entries........................................... 24
Editing and Erasing Private ID List Entries .................................... 25
Last 10 Calls Received and Sent Lists.................................................. 26
Quickstore of Phone Numbers.............................................................. 26
Making Private Calls......................................................................... 28
Scroll ................................................................................................28
Name Search.................................................................................... 28
Receiving a Private Call ................. .... .........................................................28
Private/Group Mode Speaker .......................................................................28
Call Alert.................... .... ... ........................................................................... 29
Selecting a Call Alert Tone Style ................................................................29
Setting an Alert Tone Style ............................................................. 29
Sending a Call Alert..................................................................................... 29
Receiving a Call Alert .......................................................................... 29
Call Alert Queuing................................................................................ 30
www.mot.com/iDEN
iv
Page 5
Table of Contents
Clearing or Queueing a Call Alert......................................................... 30
Responding to a Queued Call Alert....................................................... 30
Quickstore of Private IDs .............................................................................31
Storing Your Private ID ............................................................................... 31
Making Group Calls.......................................................................... 32
Receiving a Group Call................................................................................ 32
Adding and Storing a Talkgroup.................................................................. 32
Area Selection .......... ....................................................................................33
Private/Group Mode Spea ke .......... ............................. ... .... ..........................33
Advanced Features............................................................................ 34
Multi-Simultaneous Talk Group Scan.......................................................... 34
Entering Group Mode............................................................................ 34
Initiating a Group Call........................................................................... 35
Responding to a Secondary Talkgroup................................................. 35
Turning Scan On and Off ......................................................................36
Aliasing Talkgroup Mode ..................................................................... 36
Talkgroup Mode Selection by Direct Entry.......................................... 37
Talkgroup Mode Selection by Memory Scroll...................................... 37
Emergency Group Call................................................................................. 37
Placing an Emergency Group Call........................................................ 37
Canceling an Emergency Group Call.....................................................38
Receiving an Emergency Group Call.................................................... 38
Receiver Operations During an Emergency Call ..................................38
Status Message............................................................................................. 38
Entering the Status Message Function.................................................. 39
Selecting a Status Message with Direct Entry ...................................... 39
Selecting a Status Message Using Memory Scroll................................ 40
Selecting a Target by Direct Entry........................................................ 40
Selecting a Target by Memory Scroll ................................................... 40
Selecting a Target by Alpha Search...................................................... 40
Sending a Status Message ..................................................................... 41
Exiting the Status Message Function.................................................... 41
Receiving a Status Message.................................................................. 41
ID List Programming ............................................................................41
Isolated Site Operation ................................................................................. 42
Entering ISO 42
Initiating a Group Call ...........................................................................43
Exiting ISO............................................................................................ 43
Other Operations................................................................................... 43
Using Mail Services........................................................................... 44
v
Page 6
Net Mail....................................................................................................... 44
Voice Mail.............................................................................................45
Alert Receipt During Phone Call.......................................................... 45
Message Mail............................................................................................... 46
Saving and Erasing Mail........................................................................ 46
Auto Call Back ......................................................................................47
Mail Memory Full................. .... .............................................................47
Using Your Phone as a Modem........................................................ 48
TTY Users ........................................................................................48
Setting Programming Menus............................................................ 49
About Error Codes ........................................................................................54
Optional Accessories ........................................................................ 56
Batterie......................................................................................................... 56
Charging the Battery............................................................................. 56
Battery Operating Instructions.............................................................. 56
Rapid Travel Charger................................................................................... 57
Using the Rapid Travel Charger (110V/220V/240V).......................... 57
Rapid Travel Charger Operating Specifications................................... 57
Vehicular Battery Charger ........................................................................... 58
Using the Vehicular Battery Charger ...................................................58
Removing the Vehicular Battery Charger ............................................ 58
Operating Specifications....................................................................... 58
Desktop Dual-Pocket Charger ..................................................................... 59
Charging a battery................................................................................. 59
Data Operation................................. ..................................................... 59
Inserting and removing a battery from the rear pocket......................... 60
Desktop Charger Status. .... ............................. ... .... ................................60
Desktop Charger Troublesh ootin g ........................................................60
Audio Adapter ...................................................................................... 62
Using the Audio Adapter 62
Attaching/Detaching the Earpiece Microphone or Headset ................. 62
Removing the Audio Adapter.......................................................... 63
Battery Belt Clip................................................................................... 63
Using the Battery Belt Clip .............................................................63
Leather Carry Case............................................................................... 63
Hard-Install Car Kit.............................................................................. 64
Remote Speaker/Microphone ............................................................... 65
Attaching and Removing the Swivel Clip....................................... 65
Connecting the Remote Speaker/Microphone to the Portable......... 65
Operation......................................................................................... 66
vi
www.mot.com/iDEN
Page 7
Table of Contents
Safety and General Information...................................................... 67
RF Operational Characteristics .................................................................... 67
Exposure To Radio Frequency Energy ........................................................ 67
Portable Radio Product Operation and EME Exposure............................... 68
Antenna Care......................................................................................... 68
Phone Operation.................................. ... ............................................... 68
Two-way radio operation ...................................................................... 68
Body-worn operation..... ............................. ... .... ............................. .... ... 68
Data operation........................................................................................68
Approved Accessories........................................................................... 69
Electro Magnetic Interference/Compatibility............................................... 69
Facilities................................................................................................ 70
Aircraft.................................................................................................. 70
Medical Devices...................... .... ............................. .... ... ............................. 70
Pacemakers............................................................................................ 70
Hearing Aids .................................................................... ... .... .............. 70
Other Medical Devices ..........................................................................70
Use While Driving................................................................................ 71
Operational Warnings..................................................................... ... .... ....... 72
For Vehicles Equipped with an Air Bag................................................72
Potentially Explosive Atmospheres ......................................................72
Blasting Caps and Areas................................................................ .... ... 72
Operational Cautions.................................. .................................................. 73
Antennas................................................................................................ 73
Batteries................................................................................................. 73
Cleaning and Drying Consideratio ns............................... ..................... 73
Intrinsically Safe Radio
Information ........................................................................................ 75
FMRC Approved Equipment .......................................................................75
Repair of FMRC Approved Products ...........................................................77
Repair.....................................................................................................77
Relabeling ..............................................................................................78
Do Not Substitute Options or Accessories............................................ 78
Accessory Safety Information ..........................................................79
Warranty............................................................................................ 81
Patent & Trademark Information ...................................................89
Owner’s Information......................................................................... 93
vii
Page 8
Important!
Be sure to read “Safety and General Informati on” on page
67 before using your phone .
viii
www.mot.com/iDEN
Page 9
Welcome
ongratulations on purchasing your Motorola iDEN r750plus datacapable, multi-service, digital portable phone. Superior features and
state-of-the-art technology help to keep you in constant touch with all
your business and pers onal contacts.
Your r750plus phone has so many new and exciting features! With wireless
access to the Internet, you can check on t he latest news and weather, get stock
quotes, send and receive e-mail, and download information from your computer.
A missed-call indicator lets you kno w th at you received calls while you were
away.
And new ease-of-dialing features, such as Turbo Dial
Calls Received and Sent lists, help you to quickly make and return phone calls.
NOTE:Som e features may be networ k dependent or subscription only, and
may not be available in all areas. Contact your serv ic e provider for
more informati on .
The r750plus phone offers:
key and the Last 10
•Phone Mode—for cellular phone operation.
See Page 12.
•Private Mode—for two-way radio use to talk with one person.
See Page 28.
•Group Mode—for two-way radio use to talk with several people. See
Page 32.
•Net Mode—for accessing the built-in microbrowser.
See the Net Mode User’s Guide.
•Advanced Features—for monitoring multiple talkgroups, emergency
calls, status messages, and Isolated Site Operation (ISO) functions.
Dependent on Network and phone availability. See Page 34.
•Mail Services—for message, voice, and net mail. See Page 44.
•Fax and Data Transfer—for circuit data faxes and file transfers. See
Page 48.
NOTE: This manual describes the features of your phone as they were set up at
the factory. However, your carrier or your org aniz at ion may have
changed or added features. For more information, check with your carrier or your organization.
This manual provide s information abou t how Net Mode works with various
features of your r750plus phone. For information on using the microbrowser
and other component s of Net Mode, see the Net Mode User’s Guide.
1
Page 10
TTY Access
TTY access is available on y our phone. See the Wireless Data Services User’s
Guide for complete instructions.
Large-Print Manu als
A large-print version of the phone’s User’s Guide is available. For more
information on Motorola product s for people with disab ilities, c ontact Moto rola
Customer Care at 1-800-453-0920 or T TY 1-877-483-2840.
Features of yo ur r750plus Phone
** Emergency Call Button (AFU only)
VibraCall
Status Light
Volume
Control/ List
Buttons
Push-To-Talk
(PTT) Button
MENU
Option Key
On/Off Key
* Punctuation Key
Alphanumeric
Keypad
* Back Key
Microphone
or
®
Alert On/Off Button
Antenna
Earpiece
Rubber
Over-Mold
Grip
Alphanumeric
Display
Option Key
Scroll Keys
Send/End Key
1
2
3
5
4
7
6
9
8
0
Mode Key
* Home Key
* Next Key
Speaker Key
Accessory Connector
* These features are available in the Net Mode bro wser.
** Emergency Call Key is orange; VibraCall
NOTES: Remove the plastic film lens protector from the display before you
use your phone for the first time.
Some keys have multiple uses. For more information, see the Net
Mode User’s Guide.
Press any key or button to turn on the keypad backlight.
®
Alert key is black.
2
www.mot.com/iDEN
Page 11
Antenna Install for optimal signa l.
Earpiece Hold to your ear to hear the other party.
Volume Control/
List Buttons
Push-To-Talk
(PTT) Button
Mode Key Press to change modes.
Emergency Call
Button
or
VibraCall
Button
®
Alert
Press to adjust volume levels in Phone, Private, and
Group modes.
Transmit a Private or Group Call, or a Call Alert.
Press and hold the PTT button to talk; release it to
listen.
Emergency Call Button: Activates Emergency
Group Call feature (see
“Emergency Group
Call” on page 37).
VibraCall Alert Button: Turns on/off the VibraCall
Alert feature (see
“VibraCall® Alert” on page
15).
On/Off Key Press and hold to turn your r750plus phone on or
Status Light Shows the phone’s status. See Table 2 on page 5 for
Punctuation Key Add punctuation in the Net Mode browser (within
Back Key Return to the p r evious browser s cr een.
Microphone Use to speak during calls.
Rubber Over-Mold
Grip
Alphanumeric
Display
MENU Key Press to scroll through menu opt ions.
Scroll Keys Press the left key to scr oll backward or the right key
Option Keys Press the right or left option key to select the m enu
SEND/END Key Press to answer an incoming Phone call. After
Alphanumeric
Keypad
Next Word Key Press to display the ne xt word choice i n the browser
Home Key Press to return to the browser Home menu.
Speaker Key Press to hear incoming c alls through the earpiece or
Accessory
Connector
off.
more information.
T9™ Text Input).
Hold the phone more securely and comf ortab ly wit h
the rubberized grip.
View up to four lines (12 characters per li ne) or six
lines (16 characters per line) on the displ ay .
to scroll forward through menu options and lists.
option that appears in the displa y di re ctly above the
key.
entering a phone number, press to begin an outgoing
Phone call or to redial the entered phone number .
Press to end Phone calls.
Enter teleph one numbers , P r ivate Call ID s, and
alphanumeric ch aracters.
(within T9 Text Input).
the speaker during private a nd group conversations.
Connect battery charging, audio, and data
accessories.
Welcome
3
Page 12
Attaching an d Char ging the Ba ttery
Attaching the Battery
1. Insert the battery bottom-end first into
the battery guide holes on the housing
of the phone.
2. Push the battery for war d into the housing of the phone until it securely locks.
Detaching the Battery
1. Press down on the battery release button.
2. Pull on the battery and remove it.
Charging the Battery
You should charge your r750plus phone
battery overnight before initial use. This
allows your batte ry to achieve its maximum
capacity and life.
Connect the charger to the bottom of the
r750plus phone.
NOTE: For more information on charging
the battery, see
page 56
“Batteries” on
.
Battery and Charging Status
A low battery is indicated by a short, chirplike sound through the speaker. The battery
strength indicator icon shows the remai ning charge in your battery. Three bars
indicates full charge. As the charge is reduced through use, the bars
progressively reduce from three to two bars , then one bar, then disappear. The
indicator flashes when you have less than five minutes of talk time (see
Table 1 ).
www.mot.com/iDEN
4
Page 13
Welcome
Table 1: Battery Charging Status
Icon
Flashes
Charging Low Battery 0-30% 31-
Discharging Low Battery 0-10% 11-
60%
40%
6190%
4170%
91100%
71100%
Turning On Your r750plus Phone
Press and hol d th e O n/ Of f bu tto n f until a set of icons appears on your display.
Next, a welcome message displays while the r750plus phone connects to your
carrier’s network.
The Status Light (LE D) indi cator o n the r750plus phone shows the service state.
See Table 2 .
Table 2: LED Indicator
Status Light
r750plus phone status
Indicator
Flashing Red
Registering—your
r750plus phone is signing on to
your carrier’s network. Please wait.
Solid Red
No service—your
r750plus phone cannot sign on
because it is outside your carrier ’s service area.
Flashing
Green
Solid Green
In service—your
r750plus phone is ready to use.
You can now place and receive call s.
In use—your
r750plus phone is currently being used.
To make sure that you ended the last call,
press e.
Turning Off your r750plus Phone
Press and hold the On/Off button f until you see the message “Powering Off”.
5
Page 14
Connecting the Supplied Antenna
Turn your r750plus phone off before installing or
removing the antenna.
Insert the bottom of the antenna into the screw-in base on
the top of the r750plus phone. Turn clockwi se by hand
until snug. Do not force.
NOTE: Connect only the supplied NAF5075 antenna to
the antenna connector on your r750plus as it is
the only one that h as b een tested for compliance with Federal Communications Commission requirements and authorized by them for use on
this radio product. Please see
page 67 of this manual for more information.
Keypad Lock
The r750plus phone includes a Keypad Lock feature that enables you to quickly
lock the phone’s ke ypad to avoid inadverte nt l y pre s s i ng ke ys or pl a ci ng calls.
Once Keypad Lock is activated, you can on ly perform the followi ng tasks
(unless you receive an incoming call, page, etc.):
•Turn your phone On/Off
•Unlock the keypad
Activating Keypad Lock
“Safety and General Information” on
Before locking your phone’s keypad, you may want to read this entire section to
learn how to respond to incomin g calls, pages, etc.
From the Phone Ready screen, sim ultaneously press
and #. The message Keypad Locked displays on your
phone.
NOTE: Whenever a key is pressed, while in Keypad
Lock mode, the “Keypad Locked” message displays as a reminder.
*
adjb
Keypad
Locked
Receiving Incoming Calls
When you receive an incoming phone call, keypad lock will be temporarily
disabled. You may perform the followi ng:
Press e to answer the call. Or,
• Press
o under “End” to send the call to voice mail and reactivate
keypad lock.
6
www.mot.com/iDEN
Page 15
Welcome
Receiving New Mail Messages
When you receive a new mail message (see “Using Mail Services” on page 44
for more informa ti on), the keypad lock will be temporarily disabled. You may
perform the following:
•
Press o under “Later” to return to Phone Ready and reactivate the
lock. Or,
• Press o under “Now”. Pr ess o under “Read”. Press o under
“Save” or “Erase”. Once you have finished, press
o under “Exit”
to return to Phone Ready and reactive the lock.
NOTE: If you have disabled the Message Mail Noti fi cation feature, only the
c icon will display. You will not receive the read Now/Later
options.
Receiving Voice Mail
When you receive a new voice mail (see “Voice Mail” on page 45) keypad lock
will be temporarily disabled. You may perform the following:
• When New Voice Mail W ait ing displays , press o under “Exit” to
return to Phone Ready and reactivate the lock. Or,
• Press o under “Dial” to access Voice Mail service. Once you have
finished, press
# to exit Voice Mail, return to Phone Ready and
reactivate the lock.
NOTE: If you have disabled the Message Mail Notifi cation, g icon will
display, however, “New Voice Mail Waiting” will not appear.
Receiving Private (Two-Way Radio) Calls
When you receive an incoming private (two-way radio) call (see “Receiving a
Private Call” on page 28) the phone will automatically activate the applicable
mode. Once the call is terminate d and th e Displa y Tim er ha s expire d , th e phon e
will return to Phone Ready and reactivate the lock.
Deactivating Keypad Lock
From the Phone Ready screen, simultaneously press *
and #. The message Keypad Unlocked displays on
your phone.
adjb
Keypad
Unlocked
7
Page 16
Display Icons
Display icons appear on the screen to inform you of e xisting c ondi tion s . S ee the
following list.
The following icons may appear along the top of the display.
Signal Strength Indicator
Shows the signal strength. Six b ars i ndicate the strongest
signal. Calls and messages may not be sent or received in
no-signal areas.
Battery Strength Indicator
Shows the remaining charge in your battery. Three bars
show full charge . The indicator flashes whe n you have
less than five minutes of talk time remaining.
Voice Mail
Indicates that unplayed messages are wait ing in your
voice mail box.
New Message Mail
Indicates that you have new text messages in yo ur mail
box.
Unread Message Mail
Indicates that you have unread Message Mail.
Vibrate All
Indicates that the Vibrate All option is turned on. You will
not hear a ring tone.
Call Forward
Indicates that incoming pho ne calls are being forwarded.
Active Line Indication
Displays the active phone line (1 or 2).
Private/Group Speaker
Indicates that the Private/Group speaker is off. You will
hear calls through the earpiece.
Packet Data
Indicates packet data registration. The blinking arrows
indicate send and receive activity. For more information,
see the Wireless Data User’s Guide.
Some of the following icons may appear in the browser.
Secure Packet Data Connection
Indicates that your packet data information is encrypted
during transmissio n .
More Information
Indicates that there is more text to read above, below, or
above and below the current scree n.
www.mot.com/iDEN
8
Page 17
Welcome
About Modes and Menus
Modes and menus are the navigational tool s, providing access to the various
features of your r750plus phone. Pressing the Mode key
the mode choices. Pressing t he M e nu key
n takes you through the menu
m takes you through
options within each mode.
There are four modes:
Phone—for cellular phone calls. See Page 12.
•
Private—for one-to-one radio calls. See Page 28.
•
•
Group—for radio calls with all individuals in a desi gnated talkgroup. See
Page 32.
Net—for browser use. See the Net Mode User’s Guide.
•
To change modes:
m until you see the desired mode.
Press
To select menu options:
n until you see the desired menu option, then press o under t he d esi red
Press
menu option to select it.
Setting the Time and Dat e
If your carrier provides this option, you can set your phone to display the current
time and date. Unless the phone is turned off, it continues to display the current
time during a loss of service.
You have a choice of a 12- or a 24-hour clock format. See Table 3.
NOTE: When this feature is activated, your phone automatically displays local
time.
Table 3: Time Display Options
12-Hour Displa y 24-Hour Display
12:00a 00:00
6:25a 06:25
12:00p 12:00
6:25p 18:25
9
Page 18
You have a choice of either a MM/DD (month/day) or a DD/MM (day/month)
date format. See Table 4:.
Table 4: Date Display Options
Date
Month/Day Format
(MM/DD)
Day/Month Format
(DD/MM)
January 2nd 01/02 02/01
January 31st 01/31 31/01
October 9th 10/09 09/10
December 31st 12/31 31/12
If your carrier activates the time and da te , th e y are displa y ed on t he third lin e in
all modes (Pho ne, Pr ivat e, Grou p, N et). Th e tim e of d ay i s als o s hown du ring a n
active Phone call. The time and date are not displayed in Group mode when you
select an Area option.
To set the time and date format:
1. Press
*, #, 7, 1.
2. Select “Ok”. The Time/Date screen displays.
The default (preset) time and date format that displays
depends on your carrier. You can accept the default format
or select an alternate format.
adjb
71=Time/
Date
Exit Ok
adjb
71=Time/
Display:On
Exit Off
3. Press r until you see the
Time Format screen.
4. Do one of the f ollowing:
• To use the 12-hour format, go to the next step.
• To use the 24-hour format, select “24hr”. (See
adjb
Time Format
12 Hour
Exit 24hr
Table 3 on page 9.)
5. Press
6. Do one of the f ollowing:
7. To use the MM/DD format, select “Exit”.
8. Or to use the DD/MM format, select “DD/MM”, t hen
r until you see the
Date Format screen.
adjb
Date Format:
MM/DD
Exit MM/DD
“Exit”. (See Table 4 on page 10. )
10
www.mot.com/iDEN
Page 19
Welcome
9. Select “Exit” again to leave the Time/Date Program mi ng option. The
Ready screen for each mode (Phone, Group, Private, and Net) now displays
the selected time and date formats.
Changing the Display Language
You can customize your r750plus phone to display one of four languages:
English, French, Spanish, or Portuguese.
To change the displayed language:
1. Press
2. Select “Ok”.
3. When the desired language appears o n your display,
4. Select “Exit”.
The language that you select will be the displayed language.
*, #, 7, 0.
Press l or r to scroll t hr ough the language opti ons.
Selecting “Exit” at any time retains t he curr ent la nguage
selection.
select “Ok”. The displayed text immediately changes
to the selected language.
adjb
70=Language
English
Exit Ok
adjb
Language
Français
Cancl Ok
Selectable Ba ck li ght Timer
Your phone’s backlight is what illuminates the display when you receive or
make calls. Through your Programming Me nu (*,#,16), you can customize the
amount of time that your backlight remains illuminated: 0, 10, 20, or 30
seconds. By choosing zero (0) seconds, all keypad backlighting, and the Status
Light, remains off (is disabled). This means, when choosing 0 seconds, the
r750plus phone enters completely dark mode. See “Setting Programming
Menus” on page 49 for more information.
11
Page 20
Making Phone Calls
In addition to making and receiving phone calls in Phone mode, you can
forward calls, use call waiting, pu t calls on hold, and create and use stored lists.
Phone Ready is the main screen.
NOTE:See “Additional Phone Services” on page 17 for more information.
You can place a call by entering the phone number on the key pad.
1. From the “Phone Ready” screen, using the keypad,
enter the desired number.
If you make a mistake, press l once to move back one
digit, or select “Cancl” to start over.
2. Press e to place the call.
3. To end the call, press
e .
Using Other D ialing Met hods
To use other dialing met hods such as Scroll, Speed Dial, or Name
Search, names and numbers must be programmed into your phone. See
“Creating, Editing, and Using Stored Lists” on Page 22.
Scroll
1. From the Phone Ready screen, press l or r to scroll backward or forward
through the stored list of numbers and names.
2. Press
3. To end the call, press
e to place the call.
e.
adjb
Phone Ready
Line1
10:42a 11/06
Exit Ok
Speed Dial
1. From the Phone Ready screen, press n until you see the “Spd#” option on
the last line of your display.
2. Select “Spd#”.
3. Enter the assigned speed-dial number (1-100). You will see the stored
name and phone number associ ated with the speed dial number.
4. Press
5. To end the call, press
e to place the call.
e.
www.mot.com/iDEN
12
Page 21
Making Phone Calls
Name Search
1. From the Phone Ready screen, select “Name”.
2. Using the keypad, enter the first letter of the desired name, for example, to
search for the name Bob:
3. Enter “B” by pressing
4. Press
r to scroll through all the names starting with “B” until you see
“Bob”.
5. Press
e to place the call.
6. To end the call, press
Automatic Redial
If you receive a “System Busy, Try Later” message, press e to have your phone
automatically redial the number. You will hear a ring-back tone when the call is
successful.
Last Number Redial
To redial the last number that you called, press e.
2 twice.
e.
Turbo Dial
®
Key
Turbo Dial key enables you to quickly place a phone call by simply pressing and
holding the numeric key on th e keypad that corresponds to the stor ed entry in
your Phone list directory. There are nine Turbo Dial positions, 1 through 9.
NOTE: If you are on a Phone call, place the call on hold before using Turbo
Dial key.
From the Phone Ready screen:
1. Select one of the first nine entries in the Phone list
using key numbers 1 through 9. For example, press
1 for Turbo dial #1. Keypad number 0 is not avail-
able for Turbo Dialing.
2. Press and hold the desired key for two seconds to activate the Turbo Dial key. T he phone begins to dial the
number and “Phone Ready” changes to “Phone-In
Use”.
adjb
Phone Ready
1
Cancl
adjb
Phone-In Use
Office
12:45p 10/18
13
Page 22
Plus Dialing
This feature enables you to place an International call from any count ry -without entering the lo cal international access code.
1. Press and hold
that precedes the appropriate international access code needed to place the
call.
2. Enter the international telephone number.
3. Press
e.
Hands-Free Speakerphone
The r750plus phone provides the convenience of a speakerphone for hol ding
impromptu meet ings or listening to your voice mail messages.
During speakerphone operation, you may either speak or listen, but you cannot
do both at the same time.
To use the speakerphone:
1. Select “Spkr.” The “Spkr” option flashes while the speakerphone is on.
2. Place the phone 15-3 0 inches (38-76 cm) away from you. In a noisy environment, you may want to move the r750plus phone closer to you for better
transmission.
NOTE: If there is background noise in your area, you may hav e di fficu l ty
0 for two seconds. A “0” appears, then changes to a “+”
hearing a caller ’s voice or messages. To r es olve this problem:
(1) Press
n until you see the “Mute” menu option.
(2) To listen, press
“Phone-In Use” to “Phone-Mute”, indicating that the microphone is
muted.
(3) To speak, pressounder “Mute” again. The display changes from
“Phone-Mute” to “Phone-In Use”, indicating that the microphone is
on.
While the microphone is muted, you can hear incoming audio, but a
caller cannot hear any speech coming from your r750plus phone.
o under “Mute”. The display c hange s from
Receiving a Ph one Call
Press one of the following keys: e, or *, or #. Or
press any numeric key ( 0 t hrough 9). To activate the
speakerphone option, select “Spkr.”
Ending a Phone Call
Press e.
14
www.mot.com/iDEN
adjb
Incoming
Phone Call
End Spkr
Page 23
Making Phone Calls
What Is My Phone N umber?
Press *,#,1 t o display your own phone number.
adjb
VibraCall® Alert
VibraCall Alert is a vibration alert system that notifies you
of incoming Messages, Phone, Private, Group, and Data
calls. You can set a vibration al ert for all services or for individual services.
When you set vibration alerts, they are set only for the current line. If you have a
second phone line, you must sel ect that line and repeat the procedure for
selecting all services or selecting indiv idu al service s to vibrate .
The alert choices are:
• Vibe All—produces a vibration alert for all incoming calls and messages.
• Phone Vibrate—produces a vib r ation alert for incoming phone and circuit -
data calls.
• Phone Vibrate/Ring—produces a vibration alert followed by a ring tone for
phone and circuit-data calls.
• Mail Vibe—produces a vibration alert for mail messages and net alerts.
• Group/Prvt Vibe—produces a vibration alert for incoming group and
private ca l l s .
NOTE: If VibraCall Alert is set for incoming calls and messages, the power-up
sequence includes a brief vibrate cycle.
1=Own Ph#
9545553434
Exit Edit
Selecting VibraCall Alert for All Incoming Calls and Messages
Advanced Feature Units (orange button on to p of
housing): To set a vibration alert for all incoming calls an d
messages:
1. Press*,#,9.
2. Select “All”. You will receive a brief vibration alert.
After you set the alert, the display returns to the previous
mode and
q (the Vibrate All icon) appears at the top of
your display.
All Other (Non-Advanced Feature) Units (black button on
top of housing): Perform the same steps as described above, or press the black
button on top of the r750plus phone.
adjb
9=Vibrate
Alert:Off
Exit All
aqjpb
Phone Ready
Line1 Vibe
10:54a 12/09
Name Mail
15
Page 24
Selecting VibraCall Alert for Individual Services
To set a vibration alert for specific phone or mail services:
1. Press
2. Press
3. Select “Selct”. The first choice is Phone Vibrate.
4. To view the Vibe/Ring vibration alert choices, press
5. To view other choices, press
6. Select “Exit” to return to the Vibrate Alert menu.
7. Select “Exit” again to return to the previous mode.
Setting the Rin ger Volume
You can adjust the ringer volume for incoming calls. If you have a second phone
line, you must set each line separatel y. Be sure to select the desired line before
setting the volume.
1. Press
2. Press the Volume Control buttons on the side of the
3. When you reach the desired level, select “Exit”.
*,#,9.
n until you see the
“Selct” menu option.
n on the keypad.
r.
• To receive vibration alerts only for Mail, select
“Mail Vib e”, then select “On”.
• To receive vibration alerts for Group and
Private calls, select “Group/Prvt”, then select
“On”.
*, #, 3, 0. The “30=Ringer Volume”
screen displays .
The display sho w s your current ringer vol ume.
phone to listen as you raise or lower the volume. At
the lowest setting, the screen displays “Ringer Volume Silent”.
adjb
9=Vibrate
Alert:Off
Exit All
adjb
9=Vibrate
Alert:Off
Selct
adjb
Phone
Vibrate:
Vibrate Off
Exit Vibe
adjb
Group/Prvt
Vibe:Off
Exit On
adjb
30=Ringer
Volume
Exit
Setting a Ring Style for the Alternate Line
1. From the Phone Read y screen, press n until you see “Line2”.
2. Select “Line2”.
3. Repeat the procedure for "Setting an Alert Tone Style", above.
www.mot.com/iDEN
16
Page 25
Additional Phone Services
Additional Phone Services
NOTE:Som e features may be networ k dependent or subscription only, and
may not be available in all areas. Contact your serv ic e provider for
more informati on .
Call Waiting
Using the Call Waiting feature, you can answer an incoming call when you are
on another call. Call Waiting is on unless you turn it off for a particular call.
1. After the alert tone, your display shows the incoming
number and asks “Accept Call?”. To accept the call,
select “Yes”. To decline the call, select “No”.
2. Press
n, then select “Hold” to place the second call
on hold and return to the first call. Selecting “Hold”
switches you between the two calls.
3. To end the active call, press
e.
Turning Off Call Waiting
adjb
5551212
Take Call
On Line 1
No Yes
adjb
Call 1-Hold
5551212
10:54a 12/09
Hold Name
You can turn off Call Waiting if you do not want to be interrupted during a call.
1. Press
n until you see “Wait”, then select “Wait”.
2. Select “Off”. Call Waiting will be disabled for one call—but will au tom atically reset to “On” after that call.
Call Hold
When you are on a call, you can place the call on hold and make a seco nd call.
1. To place the active call on hold, press
n, then select “Hold”. Y o u ma y
then answer or place another call.
2. To remove the call from hold, press
n, then select “Hold” again.
17
Page 26
3-Way Calling
If your carrier provides 3-way calling, you can combine
two ongoing phone calls into one conversation. This option
is available only when you initiate the second call.
After you place or receive a phone call:
1. Select “3way”. This action places the current call on
hold.
2. Enter the phone num ber for t he second call and press
3. When the second call is connected, select “3way” to join the
calls. Both phone numbers and “3way” appear on your screen.
4. To end the 3-way call, pres s
e.
Alternate Pho ne Li ne
If your phone is act ivated with two phone lines, you can switch between them.
To change phone lines, your phone must be at the Phone Ready screen. The
following settings are independent for each phone line. When you enable a
setting, it applies only to the active line.
• Ringer Volume
• Auto Answer
• One-minute Beep
• Automatic Display Timer
• Resettable Timer
• Total Call Timer
• Selectable Ring Styles
• Call Forwarding
adjb
Phone-In Use
5551212
10:42a 11/06
Hold 3way
e.
Setting the Active Line
At the “Phone Ready” screen:
1. Press
n until you s ee “Line2”. (If you are on Line 2,
you will see “Line1”.)
2. Do one of the f ollowing:
• Select “Line2” to activate Line 2 when Line 1
is the active line.
• Or, select “Line1” to activate Line 1 when Line 2 is the
active line.
Outgoing calls will be made on the selected line.
www.mot.com/iDEN
18
adjb
Phone Ready
Line1
11:48a 08/21
Line2
Page 27
Additional Phone Services
Receiving a Call
You can receive calls on either line, regardless of the active line setting.
• If you receive a call on the currently active line, that icon simply flashes.
• If you receive a call on the line that is not currently active, the active line
icon remains lit and the alternate line icon flashes.
Receiving a Call on Your Alternate Line
1. Select “Yes” to answer the call on the other line. Your
previous call will be placed on hold.
2. Do one of the fo llowing:
• To end the call, press
• Or, to place the current call on hold, or to
toggle between calls, press
e.
n, then select
adjb
3055551212
Accept Call
On Line 2?
No Yes
“Hold”.
When the call ends, the phone remains active in the last active line selected.
Receiving a Phone Call Using Speakerphone
Select “Spkr” to activate the speakerphone.
Missed Call Indicator
Your r750plus pho ne notifies you of received, but
unanswered, phone calls. If you subscribe to Caller ID, the
caller’s phone number is stored i n your Last 10 Calls
Received list. Your screen displays a flashing message, for
example, “2 Rcvd Ca lls”, with the numbe r of missed calls.
Press any key to clear the flashing indicator.
To retrieve the missed calls:
1. From the Phone Ready screen, press
n. The menu
options change to “Calls” and “Spd#”.
2. Select “Calls”. The Rcvd Calls screen opens with the
number, time, and date of the last call that you
received.
3. Scroll to continue viewing the list.
adjb
Phone Ready
Line1
2 Rcvd Calls
Name Mail
adjb
Phone Ready
Line1
10:42a 11/06
Calls Spd#
adjb
Rcvd Calls
1=5552222
10:42a 11/06
Cancl Store
19
Page 28
Call Forwarding
Call forwarding lets callers reach you wherever you are. You have two options:
forward all incoming calls (unconditional) or select those circumstances
(conditional) when you want your calls forwarded.
Unconditional Call Forwarding
Unconditional call forwarding sends all incoming calls to the designated
number.
NOTE: When you set unconditional call forwarding, your phone does not ring.
1. From the Phone Ready screen, press n until you see
“Forwd” on the last line of the display.
2. Select “Forwd”.
3. To select the numb er w here you want your calls for-
warded, do one of t he following:
• Enter a number.
• Or, press the scroll keys to select a number
from your stored list.
4. Select “On”.
5. After the “Please Wait” message disp lays, select “Exit”.
6. Notice that the Call Forward icon z appears on your display when Unco n-
ditional Call Forwarding is set.
adjb
Phone Ready
Line1
9:06a 9/03
Forwd Spd#
adjb
Forwd:Off
To:5551212
Exit On
Conditional Call Forwarding
You may want to forward your calls when your r750plus phone is:
• Busy on another call or accessing the browser (Busy)
• Not answered (NoAns)
• Outside the service area (NoRch).
NOTE: You must turn off Unconditional Call Forwarding before you can set
Conditional Call Forwarding options.
1. From the Phone Ready screen, press n until you see
“Forwd” on the last line of your display, then select it.
www.mot.com/iDEN
adjb
Phone Ready
Line1
9:06a 9/03
Forwd Spd#
20
Page 29
Additional Phone Services
2. Press n once again until you see “Busy” and
“NoAns” on the last line of your display.
3. To forward your calls whe n yo ur ph on e is in use,
select “Busy”.
4. To forward your calls when you do not want to
answer them, select “NoAns”.
5. Press
6. After you select the call forwa r d option, either enter
7. Select “On”.
8. Select “Exit”.
9. You can set mor e than one condition by repeating steps 2
n again until you see “NoRch” and “Rcl#”.
• To forward your calls when you canno t be
reached, select “NoRch”.
• To see the call forward number, select “Rcl#”.
the number where you want your calls to be forwarded, or press the scroll buttons and select a number.
through 6.
adjb
Forward:Off
To:
Busy NoAns
adjb
Forward:Off
To:
NoRch Rcl#
21
Page 30
Creating, Editing, and Using
Stored Lists
A stored list is a directory of phone numbers and Private IDs and their related
names. Stored lists are convenient bec a u se you do not have to reme mb e r na me s
and numbers—you simply scroll through your stored list.
Combined Phone Number and Private ID List
You can set a combined Phone and a Private ID with the associated name, which
eliminates the need to program the Private ID separately. You can add up to 100
numbers to your Phone list, store them with names, and assign them to speeddial numbers.
Entering Numbers
To enter a number, press the corresponding key on the keypad.
Entering Names
To enter a letter, press the key the required number of times, which is related to
the letter’s position on the key. Ta ble5 describes how to enter e ach lette r on the
7 key.
Table 5: Entering Letters and Numbers on the Keypad
To enter:
P once.
Q twice.
R three times.
S four times.
7
To shift to lowercase letters, press and hold # after a letter is entered.
www.mot.com/iDEN
five times.
Press
7
22
Page 31
Creating, Editing, and Using Stored Lists
Storing Names and Numbers
1. Press *,#,2,0.
2. Select “Ok”.
The next screen briefl y displays the remaining number of
phone numbers and private IDs that you can store.
3. Enter the name that you wish to store.
Select “Store”.
See Figure 1 . for an example of ente ring a name.
Example
To store the name “TIM”:
1. Enter “T” by pressing
2. Enter “I” by pressing
3. Enter “M” by pressing
8 once.
4 three times.
6 once.
adjb
20=Phone/
Prvt List
Exit Ok
adjb
Available
98 Phone #
3 Prvt IDs
adjb
Enter Name
-
Exit Store
Figure 1. Entering a Name
2. Enter the phone number that you want to associate
with this name and select “Store”.
To skip the Phone Number entry, select “Skip”. You will
go directly to the “Enter Prvt ID Nu mber” screen.
The next screen displays the name that you entered and a
flashing speed-dial number where th e entry will be stored.
3. Do one of the foll owing:
• To accept the speed-di al number shown, select
“Store”.
• To change the speed-di al number, enter
the desired speed-dial number. The speeddial number stops flashing.
4. At the next screen, enter the Private ID number associated with the name that you entered then select
“Store”.
To skip the Private ID number entry, select “Skip”.
adjb
Enter Phone
Number
Skip Store
adjb
TIM
Spd#=3
Cancl Store
adjb
Enter PrvtID
Skip Store
23
Page 32
Pause Digit Entry
When storing a number, you can program your phone so that it will not only dial
a number but also pause and enter another series of numbers such as a personal
identification number (PIN) or password. This feature is particularly useful for
automated services such as voice mail and banking systems.
Here’s how it works: Let’s say you have a company voice mail account that you
frequently check while on travel. And, to access that account currently you must
do the following:
• Dial your work number;
• Press * while the voice mail greeting is bei ng played; and
• Enter your PIN to acc ess your messages.
You can program your r750plus phone to enter all of the above information for
you. All you have to do is separate each entry with a pause. If you were to
program your phone to input the above information, the stored data would look
like this: 17035551234P1234. In this example, the first eleven digits represent
the number that must be dia led to access your voice mail. The P represents a 3
second pause. The last four digits represent your PIN.
You can use this feature not only to enter PINs and passwords but a lso to have
the phone automatically select menu options (i.e., press 1 to hear messages).
To create a three-second paus e fol l ow t he st eps below:
Press and hold * for two seconds. The pause symbol (P) will
•
appear.
NOTE: You can enter up to 20 numbers/characters in a single entry, stored or
dialed. If you use a system that will not let you enter an option until the
automated message has played in its entirety, you can program your
phone to pause for more than 3 seconds. For example, performing the
above step twice will program two pauses and cause your phone to wait
6 seconds before entering the next set of numbers.
Editing and Erasing Phone List Entr ies
1. Press *, #, 2, 1.
2. Select “Ok”. The “Edit Entry?” screen displays .
3. Do one of the f ollowing:
a. To edit an entry, select “Ok”.
(1) At the “Edit Entry” screen, press
then select “OK.
(2) At the “Edit Number” screen, edit the phone number, if you wish,
then select “Store”.
(3) At the “Edit Name” screen, edit the name, if you wi sh, then select
“Store”.
(4) At the “Edit Spd#” screen, edit the speed nu mber, if you wish, then
www.mot.com/iDEN
r until the desired entry appears,
24
Page 33
Creating, Editing, and Using Stored Lists
select “Store”.
b. To erase an entry:
(1) At the “Edit Entry” screen, press
l or r.
(2) At the “Erase Entry” screen, select “Ok”.
(3) Scroll to the desired entry, then select “Ok”. At the “Erase Entry?”
screen, select “Yes”.
4. Select “Exit” to close the Phone List Edit screen.
Editing and Erasing Private ID List En tries
1. Press *, #, 2, 2.
2. Select “Ok”. The “Edit Entry?” screen displays.
3. Do one of the fo llowing:
a. To edit an entry, select “Ok”.
(1) At the “Edit Entry” screen, press r until the desired entry appears,
then select “OK.
(2) At the “Edit ID” screen, edit the number, if you wish, then select
“Store”.
(3) At the “Edit Name” screen, edit the name, if you wish, then select
“Store”.
b. To erase an entry at the “Edit Entry” screen, press
select “Ok”. Press
r to scroll to the desired entry, then select “Ok”.
At the “Erase Entry?” screen, select “Yes”.
4. Select “Exit” to close the Private ID List Edit screen.
l or r once, then
25
Page 34
Last 10 Calls Received and Sent Lists
If you subscribe to your carrier’s Caller ID service, you can view, dial, and store
the list of the last ten phone numbers received and the last ten phone numbers
dialed.
The most recent call sent or received appears first in your call list.
From the Phone Ready screen:
1. Press
2. Select “Calls”. The Rcvd Calls screen opens.
3. Do one of the f ollowing:
4. To view the Calls Received l ist again, select “Rcvd”.
5. To close the Calls list, select “Cancl”.
Quickstore of Phone Numbers
n. The menu options change to “Calls” and
“Spd#”.
If the “Store” option appears, the number currently displayed is not in your Phone list. To add the num ber to
your list, select “Store”.
If you want to see the Sent list but the “Store” option is
on your display, press
n until you see the “Sent” menu
option.
• To view the Calls Received list, use the Scroll
key to view each entry.
If the “Store” option is on your display, press n until
you see the “Rcvd” menu option.
• Or, to view the Calls Sent list, select “Sent”.
Use the Scroll key to view each entry.
adjb
Phone Ready
Line1
12:55p 10/18
Calls Spd#
adjb
Rcvd Calls
1=5554444
12:55p 10/18
Cancl Store
adjb
Rcvd Calls
2=MAILBOX
12:56 10/18
Cancl Sent
adjb
Sent Calls
1=JOHN
12:56p 10/18
Cancl Rcvd
If you subscribe to yo ur carrier’s Caller ID ser vice, you can use Quickstore to
store the last number that you dialed or quickly store a number from the Last 10
Calls Received and Sent Lists without having to enter the programming menu.
NOTE: As you scroll through the Last 10 Calls Received or Sent List, only the
name displays. If the name is not available, the phone number displays.
To use Phone Number Quickstore , from either the Phone
Ready screen or from the Last 10 Calls Received or Sent
List:
1. Do one of the f ollowing:
• To go to the last call that you dialed,
press r.
adjb
Phone Ready
Line1
12:43p 07/22
Name Mail
• To view the Received and Sent Calls list,
press n until you see “Calls”, then select it.
26
www.mot.com/iDEN
Page 35
Creating, Editing, and Using Stored Lists
2. Select “Store”. The Enter Name screen displays.
3. Enter the name then select “Store”.
The combined name and number entry is stored in the first
available storage space.
The Stored message displays with the name that you
stored.
adjb
Phone Ready
0=5554455
Cancl Store
adjb
Enter Name
-
Cancl Store
adjb
JOHN
5551212
Stored
27
Page 36
Making Private Calls
A Private call is a one-to-one conversation between two people. In Private
mode, each phone is identified by a name or a number called a Private ID.
To make a Private Call:
1. Press
2. Use the keypad t o enter the Private ID of the person
3. To speak, press and ho ld the PTT button, wait for the
4. To listen, release the PTT button.
To use Scroll or Name Search, you must have a Private ID list.
Scroll
1. Press m until you see “Prvt Ready” on your display.
2. Press
3. Press and hold the PTT button, wait for the chirp, then speak into the
Name Sear c h
1. Press m until you see “Prvt Ready” on your display.
2. Select “Name”.
3. Press the key with the first letter of the name you are searching for.
4. Press
5. Press and hold the PTT button, wait for the chirp, then speak into the
m until you see “Prvt Ready” on your display.
adjb
that you want to reach.
chirp, then speak into the microphone.
l or r to scroll through the stored Private ID list.
Prvt Ready
JOHN SMITH
12:43p 07/22
Alert Name
microphone.
l or r to scroll through other stored names associated with the let-
ter you entered.
microphone.
Receiving a Pr ivate C all
When you receive an incoming Private ca ll, you hear a brief chi rp-like tone.
Your r750plus phone automat ically switches to Private mode, and the Private
ID or the name of the caller displays.
1. Your phone must be idle, that is, not busy in an active call or on the
browser.
2. Wait for the caller to finish speaking.
3. Press and hold the PTT button. Begin speaking after you hear the chirp.
Private/Group Mode Speaker
You can hear Private calls through either the earpiece or the speaker. Press the
Speaker button
Speaker on or off.
28
k on your r750plus phone to turn the Private/Group Mode
www.mot.com/iDEN
Page 37
Making Private Calls
• With the Speaker on, you will hear incoming calls through the speaker.
• With the Speaker off, you will hear incoming calls through the earpiece.
Call Alert
Call Alert enables yo u to page an individual by sending an audibl e ton e . A Call
Alert allows the individual to respond when it is convenient. The alert plays
intermittently until the individual clears it.
Selecting a Call A lert Tone Style
Your phone has ten selectable Call Alert tones.
Setting an Alert Tone Style
1. Press *, #, 3, 7.
1. The display shows your current Alert tone.
2. Select “Ok”.
3. Press l or r to scroll through the available Alert
tone styles.
4. To listen to the selected Alert tone, press the Volume
buttons on the side of the phone.
5. Select “Ok” to select the Alert tone shown.
adjb
37=Set Alert
Style:1
Exit Ok
adjb
Alert
Style 4
Cancl Ok
To leave the Alert tone style unchanged, select “Cancl”
6. Select “Exit”.
Sending a Call Alert
1. Press m to go to the “Prvt Ready” screen.
2. Select “Alert”.
3. Enter th e Private ID, or press
l or r to scroll to the
desired name. You may also select the name by press-
n and using Name Search.
ing
4. Press the PTT button.
Receiving a Call Alert
When you receive a Call Alert, you will hear an a lert ton e and see a message o n
your display.
• To answer the Call Alert, press the P T T butt on.
• To clear the Call Alert without answering it, select “Clear”.
adjb
Prvt Ready
JOHN
12:43p 07/22
Alert Name
adjb
Alert 0
JOHN
Exit Queue
29
Page 38
• To silence the Call Alert without clearing it, press any key other than the
PTT button.
NOTE: Until the Cal l A le rt is cleared or returned, th e alert plays intermi t -
tently and you will not be able to receive any additional Phone, Private,
Group, or Net calls.
Call Alert Queuing
If your carrier provides Call Alert Queuing, you can save up to eight Call Alerts
in a queue for later use.
After you respond to the Call Alert, it is removed from the queue.
Clearing or Queueing a Call Alert
When you receive a Call Alert, do one of the following:
• To clear a Call Alert, select “Clear”.
• To place the Call Alert into the queue, select “Queue”.
Pressing
m also queues the Call Alert.
If you receive multiple Call Alerts, the last recei ved Call
Alert displays and the remaining Call Alerts are stacked at
the beginning of the queue.
Responding to a Queued Call Alert
adjb
Alert 3
JOHN SMITH
Clear Queue
You can respond to the Call Alerts in any order. To select a Call Alert for
response:
1. Select “Queue”.
2. Press
l or r to scroll to the desired Call Alert.
3. Press the PTT button to respond to the Call Alert.
30
www.mot.com/iDEN
Page 39
Making Private Calls
Quickstore of Pri va te I Ds
Quickstore allows you to quickly store a received or sent Private ID, without
having to enter the programming menu.
From the Private Ready screen, with the P r iv ate ID
displayed:
1. Select “Store”.
If an ID is gr eater than 12 charac ters in lengt h, the ID
wraps to the third line.
2. Enter the name associated
with the Private ID.
3. Select “Store”. The Stored messag e displays.
If the list is full with the maximum 100 entries, you
will get the message, “Prvt List Full”. You cannot
add names until you remove some names from the list.
4. Next, the display returns to the Private Ready mode.
Storing Your Privat e ID
NOTE: For non-Crossfleet enabled networks only.
To store your Privat e ID in your r750plus phone:
1. Press
2. Select “Ok”.
3. Enter the Private ID provided by your carrier.
4. Select “Store”.
To view your Private ID at any time afte r you store it:
1. Press *,#,2. The screen displays the message, “2=Own Pvt ID”.
2. Select “Exit”.
*,#,2. The screen displays the message, “2=Own Pvt ID”.
The next line displays your Priv ate ID. This is the number supplied by your
carrier that you store in your phone.
adjb
Prvt Ready
56781
12:43p 07/22
Alert Store
adjb
Enter Name
-
Cancl Store
adjb
JOHN
Stored
adjb
Prvt Ready
JOHN
12:43p 07/22
Alert Name
31
Page 40
Making Group Calls
A Group Call allows you to communicate instantly with members of a selected
Talkgroup–a pre-defined set of people who shar e a communication need.
Talkgroups appear on your display as numbers or programmed names, such as
Talkgrp10 or Sales Team.
To make a Group Cal l:
1. Press
2. To place a call, do one of the following:
3. To listen, release the PTT button.
Receiving a Grou p Call
When you receive an inc om in g Group c all, you will hear a brief chirp-li ke tone .
Your r750plus phone automati call y swit che s to Grou p mo de, and the T alkg rou p
name displays.
1. Your phone must be idle, that is, not busy in an active call or on the
2. Wait for the caller to finish speaking, then press and hold the PTT button.
3. To listen, release the PTT button.
You can receive group calls only in the Talkgroups that you are provisioned for.
For more information, see “Adding or Storin g a Talkgroup” on Page 32.
m until “Group Read y” displays. Your most
recently used talkgroup displays, for exa m ple ,
“T a lkg rp 10”.
• To speak to this talkgroup, press and hold the
PTT bu tton. Wait for the chirp, then speak into
the microphone.
• To speak to another talkgroup, press
desired talkgroup name. Press and hold the PTT button. Wait for the
chirp, then speak into the mi crophone.
browser.
Begin speaking after you hear the chirp.
l or r until you see the
adjb
Group Ready
1:Tg1
S Off Sts
Adding and Storing a Talkgroup
To add and store a talkgroup name to your r750plus phone :
1. Press
2. Select “Ok”.
3. At “Add New Entry?”, select “Ok”.
4. At “Enter ID”, enter the desired talkgroup number and select “Store”.
5. At “Enter Name”, enter a name for the talkgroup and select “Store”.
32
*,#,2,3.
www.mot.com/iDEN
Page 41
Making Group Calls
Area Selection
In Group mode, you can call only those talkgroup members in a specific
location. This is useful when you know where the individuals are located within
the service area.
1. Press
2. Press
3. Press
m until you see “Group Ready” on your display.
n, then select “Area”.
l or r to scroll through the targeted areas specified by your local
carrier.
4. Select “Ok” to select the targeted area.
Private/Group Mode Speaker
You can hear Group calls through ei ther the earpiece or the speaker.
Press the Speaker button
Mode Speaker on or off.
With the Speaker on, you will hear incoming calls through the spea ker. This is
useful to monitor talkgroup ac tivity in Group mode.
With the Speaker off, you will hear incoming calls through the earpiece.
k on the r750plus phone to turn the Private/Group
33
Page 42
Advanced Features
Some r750plus phones are provided with an advanced feature set as described in
this section. Please contact your service provider for more information.
Multi-Sim ul ta neo us Talk Group Scan
Multi-Simultaneous Talkgroup Scan (Scan) allows users within a fleet to
monitor more than one talkgroup. A Talkgroup Mode, within the range of 1255, is comprised of up to four talkgroups (one Primary Talkgroup and up to
three Secondary Talkgroups). Calls can only be initiated on the user’s Primary
Talkgroup; however, a user can respond to an active call on eithe r a Primary or
Secondary Talkgroup. Both Primary and Secondary Talkgroups, as well as the
Talkgroup Mode , can be named (aliased). The Scan feature is set to “ON”, but
the user has the capability of d isabling Scan through an opt ion key . The unit will
store the last Scan setting, and power on with that setting.
Entering Group Mode
1. Press the f key to power on your unit. Press m to enter Group Mode.
Two different Talkgroup Modes are displayed below. The Primary Talkgroup is
indicated to the r ight of the Talkgr oup Mode. The display on the left shows a
non-aliased Primary Talkgroup, and the display on the right shows an aliased
Primary Talkgroup.
ab
Group Ready
Group Ready
102:Tg 15
102:Tg 15
S Off Sts
S Off Sts
Primary Talkgroup
Not Aliased
34
www.mot.com/iDEN
ab
Group Ready
Group Ready
3:Electricia
3:Electricia
S Off Sts
S Off Sts
Primary Talkgroup
Aliased
Page 43
Initiating a Group Call
Advanced Features
1. Press and hold the PTT button to initiate a group
call on your Primary Talkgroup.
The example to the right illustrates the display if Fred
pressed the PTT button to initiate a call on the
ab
Group Ready
3:Electricia
S Off Sts
Electricians talkgroup. This is Fred’s Primary
Talkgroup for Mode 3.
Fred’s Display
All subscriber units that have affiliated with your
Primary Talkgroup as eit her a P rimary or Secondary Talkgroup in any
Talkgroup Mode will receive your group call if they are not already engaged in
an active call.
The following screens will be displayed on the receiver subscriber units
indicating they have joined the call. The second line of the display will indicate
the Mode number followed by Primary or Secondary Ta lkgroup, which may be
aliased. The third line of the display indicates the PTT-ID of the unit initiating
the group call, whic h can also be aliased.
Example: Jason joi ns the Ele ct r ic ia ns t al kg rou p. He has
also selected Electricians as his Pri mary Talkgroup for
Talkgroup 3, but he has no alias for his talkgroup, so the
Talkgroup numbe r (TG ID) is dis playe d. Fred’s PTT-ID
is displayed on the third line.
ab
Group Ready
3:Tg 3
ID:Fred
S Off Sts
Jason’s Display
Example: Julie joins the call and the unit updates the
alias to indicate active Secondary Talkgroup (Mode 1,
Secondary Talk gro up 3 ). Fr ed’s PTT- ID is di sp laye d on
the third line.
Responding to a Secondary Talkgroup
ab
Group Ready
1:Electricia
ID:Fred
S Off Sts
Julie’s Display
1. To respond to a call on a Secondary Talkgroup, press the PTT button.
Example: Julie responds to Fred by pressing the PTT
button.
ab
Group Ready
1:Electricia
S Off Sts
Julie’s Display
35
Page 44
Fred has released his PTT button, then begins to receive
Julie’s response.
ab
Group Ready
3:Electricia
ID:Julie
S Off Sts
Fred’s Display
Jason receives Julies’s response.
After the Secondary Talkgroup call is completed, all
receiving subscriber units’ displays will revert to their
Primary Talkgroup of the selected Talkgroup Mode.
Turning Scan On and Off
ab
Group Ready
3:Tg 3
ID:Julie
S Off Sts
Jason’s Display
The capability to turn scan on and off is available as an option key.
1. Press the “Scan” option key.
Press the “S Off” soft option key to disable scan.
ab
Group Ready
Group Ready
18:Engineers
102:Tg 15
S Off Sts
S Off Sts
Scan Enabled Scan Disabled
ab
Group Ready
Group Ready
18-Engineers
3:Electricia
Scan Sts
S Off Sts
When Scan is disabled, you will not have access to your Secondary Talkgroups
Aliasing Talkgroup Mode
The r750plus phone allows you to Alias Talkgroup Modes and Primary and
Secondary Talkgroups.
1. Press *, #, 2, 5.
2. Select “Ok”.
3. At “Add New Entry” select “Ok”.
NOTE: Press l or r to Edit or Erase a Talkgroup Mode Alias.
4. Enter the ID of the desired talkgroup mode and press “Store”.
NOTE:The Aliased Modes are displayed only while scrolling through the Talk-
group Mode or during Direct Entry. In an idle or transmission state,
the Mode ID number is displayed. This ensures that the Mode ID number and Primary Talkgroup are displayed simultaneously on screen.
5. Then enter the name of the desired talkg roup mode alias and press “Store”.
36
www.mot.com/iDEN
Page 45
Advanced Features
Talkgroup Mode Selection by Direct Entry
You may select a diff e rent Talkgroup Mode at any time.
1. Press the
hold
1 key. To erase a digit, press l. To clear all digits, press and
l. To return to your previously sel e cted Talkgroup Mode, press the
“Cancl” option key.
2. Press the
3. Press the PTT button or the “Ok” option key.
“Mode 18” will flash until affiliation is complete.
If you selected th e Talkgrou p Mode by pres sing the
PTT button, you will in itiate a call on your Prim ary
8 key.
ab
Group Ready
18_
Cancl Ok
Talkgroup.
Talkgroup Mode Selection by Memory Scroll
The Memory Scroll feature allows you to use the l or r keys to sc rol l thro ugh
memory for Talkgroup Modes.
1. Press
2. Press the PTT button or the “Ok” option key.
r. Press and hold this key to Auto Scroll
through your lists more quickly.
NOTE:To transmit, press the PTT button; to listen
only, press “Ok”.
ab
Group Ready
Mode 18
Cancl Ok
Emergency Group Call
NOTE:If your r750plus phone has an orange button on top of the housing, the
Emergency Cal l fe atu re is present.
Emergency Group Call is a carrier-dependent feature. Please contact your
carrier for service availability.
Placing an Emergency Group Call
An Emergency Group Call allows a user to have priority access to his talkgroup
members and provide them visual and audible indications o f an emergency
condition. The Emergency call can be placed from any mode (private, group,
phone, Net).
1. Press and hold the Em ergen cy Butt on. The p ortable will emit an e merge ncy
start tone to indicate that you h ave successfully requested an emergency
call.
2. Press the PTT button to talk. Th e currently sele cted
Talkgroup Mode will be selected unless your organization pre-programmed an emergency Talkgroup
Mode. If this is the case, the pre-pr ogrammed
Emergency Talkgroup Mode will flash in the dis-
ab
EMERGENCY
1: SE Plant
ID:John
37
Page 46
play. The Talkgroup Mode appears in the second line of the display as
shown.
3. To end an emergency call, press and hold the Emergency Button for 3 seconds. The portable will return to the last selected talkgroup mode. The initiator cannot exit the emer gency call with out first canc elling the e mergency
call.
Canceling an Emergency Group Call
Press the Emergency Button until the unit generates an Emergency Call Cancel
tone. This tone indicate s the cancell ation has oc curred. The d isplay will return to
the non-emergency state.
An emergency call will be cancelled if no talkgroup activity occurs for 30
seconds. The dispatch er, or any other person provisione d to cancel an
emergency call can also cancel the emergency call.
Receiving an Emergency Group Call
When an emergency call is initiated, other members of the talkgroup will be
notified of an emergency condition.
The receiving unit will hear an Emergency Receive
Tone, and the receiver’s display will change to indicate
the condition.
The first line of the display will indicate the ID or alias
of the person initiating the emergency call. The second
line will show you the Talkgroup Mode and Active
Talkgroup name or number. The third line shows you the ID or alias of the
person who is currently speaking. The third line will remain blank when the
receiving unit initiates a transmission.
ab
EMER:58
1:SE Plant
ID:Cheryl
S Off Sts
Receiver Operations During an Emergency Call
Other members of the Emergency Gro up Call can leave the emergency call and
change modes (phone, group, private, Net) while involved in the call.
While listening to the emergency call, the receiving unit will not receive phone
calls, Call Alerts, Message Mails, Statu s Me ssages, Priv at e Call s or o the r g rou p
calls for the duration of the emergency call.
Status Message
Status Message lets you send a pre-defined message to the dispatcher or to
another user’s ID. Up to ten pre-defined alphanumeric Status Me s sages are
available such as “At Lunch” or “En Route”.
38
www.mot.com/iDEN
Page 47
Advanced Features
You can also send any numeric Statu s Message from 1-255. A Status Message
can be sent by selecting both the Status Message and target ID (alias) of the
person who is to receive the Status Message. You can reduce talk time by
sending Status Messages. You can also leave a Status Message for receivers
while they are away from their portables.
Entering the Status Message Function
1. Press the Status Option Key to get to the Status Message function. You
must be in Group or Private Mode to access this function.
The second line of the display shows the Status Mes-
sage (alpha or numeric) of the last successfully
sent status.
2. Press Option “Exit” to return to either the group or
Private mode. Press Option “Targt” to go to the
ab
Sts Message
En Route
Exit Targt
Target ID selection screen.
Selecting a Status Message with Direct Entry
Direct Entry allows you to use the keypad to select the message you want to
send. Enter any number from 1-255 to select a Status Message. The number can
correspond to on e of ten pre - programmed alphanum er ic sta tus messages or any
other numeric Status Message within the range of 1-255.
1. Press 2.
2. Press “Ok”. Pressing the PTT button at this time
will send the message to the last unit to which you
sent a successful message.
3. Press “Targt” to select a target for this message.
ab
Sts Message
2= At Lunch
Cancl Ok
39
Page 48
Selecting a Status Message Using Memory Scroll
You can select Status Messages by using the l or r keys to scroll through the
ten named (aliased) Status Message s which you have progra mmed.
1. Press
2. Press “Ok”.
3. Press “Targt” to select a target for this message.
Selecting a Target by Direct Entry
r until you find the message you want. In
this case we scrolled to the Status Message “At
Lunch”.
ab
Sts Message
At Lunch
Cancl Ok
1. Enter the numeric ID of the person to whom you
are sending the message.
2. Press “Ok”.
3. Press the PTT button to send the message to the
selected ID.
ab
Sts Target
5= Rochelle
Cancl Ok
Selecting a Target by Memory Scroll
You can select a target by scrolling though the portable IDs or aliases by using
l or r keys.
the
1. Press the
you want to send the message.
2. Press “Ok”.
3. Press the PTT button. The disp la y sh ows the me ssage that has been sent.
r key until you find the person to whom
ab
Sts Target
Julie
Cancl Ok
Selecting a Target by Alpha Search
You can select a portable ID by selecting the first letter of the name (alias). If no
name is stored under a letter, the unit will automatically search forward,
alphabetically, until the next name is found.
1. Press the “Name” key.
2. Press a numeric ke y. i.e.: Press
7 three times to
view the names (aliases) that begin with the letter
R.
3. Use either the
l or r keys to scroll to the name
(alias) who is to receive the Status Message.
4. Press the PTT button. The disp la y sh ow s t he me s sag e tha t ha s been sent.
ab
Name:Sts
R=Randy
Cancl Ok
40
www.mot.com/iDEN
Page 49
Advanced Features
Sending a Status Message
After selecting both a Status Message and a desired target ID, press the PTT
button to send the message. Two high pitched tones will be heard during
transmission.
If successful, two high pitched tones will be heard to
indicate the message was successfully delivered to the
target portable.
ab
Sts-Sent
Successful
If unsuccessful, an alert tone will be heard to in dicate
that the targeted unit is busy, out-of-range, or turned-off.
In either case, the portable will return to the status
ab
User Not
Available
screen after 3 seconds.
Exiting the Status Message Function
Press the m key to exit the Status Mes s age screen. Pressing the “Exit” option
key from the Status Message screen will also allow you to exit the status
message function.
Receiving a Status Message
The portable will receive a message along with alert
tones. To silence the recurring alert tones only, press
any key except
m or the “Clear” option key. In case of
a non-aliased sender ID, the Quickstore option is
available.
If a non-aliased ID is sent, the Quickstore softkey is
displayed.
All calls remain blocked until this message is cleared.
ab
Sts-Kelly
At Lunch
Clear
ID List Programming
Feature menu #26 allows you to program ten status
messages, each up to 12 characters long.
ab
26=Sts Mesg
List Program
Exit Ok
41
Page 50
Isolated Site Operation
Isolated Site Operation (ISO) allows group call communications to continue
within a single cell site when co nn ec tivi t y t o the ne two rk is lo st b y allo wing th e
cell to operate in a local, one cell only mode. ISO is limited to dispatch
talkgroup calls only. In all modes the display will update to include “-Isoft” on
the first line. Talkgroup communications will be limited to only those units that
are connected to the ISO cell, and only on the talkgro up o r Talkgro up Mo de tha t
the subscriber unit last used before the cell entered the ISO state.
Entering ISO
The portable will enter the ISO state when i ts cell becomes isolated from the
network, assuming the portable has no available neighbor cells. It will display
one of the following screens: (The LED indic a tor is off in IS O un less the uni t is
transmitting. While transmitting, the LED will be green.)
NOTE:If the portable is powered on in an ISO cell, it will enter the ISO state if
there are n o av a i lable neighbor cells.
Phone Mode
Group Call Mode
Private Call Mode
Net Mode
ab
Phone-Isoft
Name Mail
ab
Group-Isoft
3:Electricia
S Off Sts
ab
Prvt-Isoft
Julie
Alert Name
ab
Net-Isoft
Julie
Alert Name
42
www.mot.com/iDEN
Page 51
Advanced Features
Initiating a Group Call
If the portable has Scan enabled when the site enters ISO, the portable will be
able to initiate a call on its Primary Talkgroup and can respond to calls started
on either the Primary or any Secondary Talkgroup.
The portable will not be able to select a new Talkgroup
Mode while in ISO condition.
If the portable has Scan disabled when the site enters
ISO, the portable will be able to initiate and respond to
calls on the Primary Talkgroup only.
ab
Group-Isoft
3:Electricia
S Off Sts
Exiting ISO
When the cell returns to normal operation, the unit will
revert back to standard operation. The green LED
indicator will resume blinking.
If the unit goes out of range of the ISO cell and has no
available neighbor cells, the unit will go out of service.
ab
Group Ready
3:Electricia
S Off Sts
Other Operations
Since the ISO operation is limited to group calls only, any attempts to
communicate in other modes (phon e, private, alert, status) will result in a
“Service Not Available” message. However, all other functions (memory scroll,
direct entry, feature menu programming, etc.) are still operable.
43
Page 52
Using Mail Services
NOTE:Some features may be network dependent or subscription only, and
may not be available in all areas. Contact your service provider fo r
more information .
Your r750plus phone provides the following mail services:
• Net Mail
• Voice Mail
• Message Mail
When you receive a new message, the
appears and flashes.
• To read your new mail immedi ately, select “Now”.
• To read your new mail later, select “Later”.
An asterisk * next to a mail service indicates new mail.
To use message services, select “Mail” from any Ready
screen. The inbox screen opens with your message services
listed.
To select a message service, scroll to highlight the service
or press the corresponding number. For example, to access
your Message Mail, press 2.
c icon
a d c b
New Mail
Read?
Later Now
a d c b
1>Voice Mail
*2>Mesg Mail
3>Net Mail
Exit Ok
Net Mail
Net Mail alerts you when you receive alerts from the Brows er, for exam pl e,
notification of an e-mail or fax.
From any mode:
1. Select “Mail”.
2. Select “Net Mail”, then select “Ok”.
The Alerts inbox opens and displays the type of Net Mail
alerts.
The Inbox screen opens.
3. Scroll to the type of alert that you wish to view, then
select “Ok”.
www.mot.com/iDEN
44
adjb
1>Voice Mail
2>Mesg Mail
3>Net Mail
Exit Ok
adjb
Inbox
1 Email
2 Fax
Ok Del
Page 53
4. To read the message, select “View”.
Using Mail Services
adjb
Inbox:1unread
1*Lunch
2 MEETING
View Menu
5. After you read the message, do one of the followi ng:
adjb
LUNCH
----
With client at
12:00
Next Menu
• Select “Menu” to view a list of actions that you
can take for this message, suc h as reply, delete,
save, and so forth.
• Or, select “Next” to read the next
message.
adjb
1>Reply
2>Delete
3>Save
4>GoTo Message
Ok More
Voice Mail
When your r750plus phone receives a Voice Mail message:
• The
• The Voice Mail alert tone sounds (if Mail Notification is turned on).
• The message, “New Voice Mail Waiting” appears on your display.
• An exclamation point (!) on the display indicates that you have at least one
From any mode:
1. Select “Mail”.
2. Select “Voice Mail”.
The Voice Mail inbox opens and displays the number of
your new and total Voice Mail messages .
To retrieve your voice mail immediately:
1. Select “Dial”. This action automatically places a call
2. To close your voice ma ilbox, select “Exit”.
g icon appears on your display.
urgent message.
to your voice mailbox. The most recent message is
retrieved first.
a gjb
1>Voice Mail
2>Mesg Mail
3>Net Mail
Exit Ok
a gjb
Voice Mail
1 New
1 Total
Exit Dial
Alert Receipt During Phone Call
Through your programming menu (*,#, 15) you can delay Voice Mail and
Message Mail Alerts so that yo u are not interrupted by the alert tone while on a
call. You can choose the following:
Receive All Alerts
•
• Delay All Alerts
45
Page 54
• Receive Message Mail Alerts only
See “Setting Programming Menus” on page 49 for more information.
Message Mail
Message Mail can be either a numeric page or a text message of up to 140
characters. Your phone can re ceive and store 16 mail messages at any time.
1. To pos tp on e re ad ing your mail and to clear the display, select “Later”. The
icon stops flashing but remains on your displ ay to remind you that you
have unread messages.
To read your mail now:
2. Select “Now”. T he scree n will bri efly di splay t he numbe r of ne w and save d
messages in your mailbox.
3. A list of all your messages will display. Highlight the message that you
wish to read and select “Read”.
To read you mail later:
4. From any mode, sel ec t “Mail”. The Mailbox opens.
adjb
1>Voice Mail
2>Mesg Mail
3>Net Mail
Exit Ok
5. Select “Mesg Mail”.
adjb
Message Mail
Your message m ai l bo x o pe n s an d briefly displays the
number of new and saved messages currently in your
mailbox.
Next, a list of all messages will display. Select th e message
that you wish to read and select “Read”.
Saving and Erasing Mail
2 New
0 Saved
adjb
*>FR: Smith
*2>FR: Jones
Exit Read
Your message shows the time and date that the sender entered it in the network
After you read a text or numeric message, you can either
Save or Erase the message. Press
option.
www.mot.com/iDEN
o under the desired
adjb
1>Call
5551212
11:15a 04/02
Erase Save
46
Page 55
Using Mail Services
Auto Call Back
You can respond to numeric pages and text messages containing a call-back
number. To automatically dial a numbe r conta ined with in a Me ssage Ma il, pre ss
e.
Mail Memory Full
If all 16 message registers are full, your phone displays the message “Mail
Waiting, Memory Full”. You cannot receive new Message Mail until you empty
register space by erasing saved or unrea d messages.
47
Page 56
Using Your Phone as a Modem
NOTE:Some features may be network dependent or subscription only, and
may not be available in all areas. Contact your service provider fo r
more information .
You can use your r750plus phone as a modem for data transfer from your
laptop, hand held device, or desktop computer. This is particularly useful when
there is no wired phone line (wall jack) available.
You simply attach a da ta cable (available separately) to your phone and your
computer. From t hat point, your phone is your modem. This allows you t o send
or receive time-critical informati on such as e-mail, a field service report, or
files. In addition, you can also send or receive fax es.
This type of wireless connection uses one of two types of data connection:
circuit-switched data and packet data.
• Circuit-switched data is typically used for sending and
receiving faxes and for transferring large files.
• Packet data is used for small file transfers such as e-mail.
To use these services, you must install the iDEN Wireless Data Services
software (available separately). For more information on setting up your
computer and your r750plus phone for Packet and Circuit Data calls, see the
Wireless Data Services User’s Guide and contact your carrier.
TTY Users
You can use your phone and computer in TTY mode. Your computer
screen and keyboard replac e th e st andard TTY device. For more
information, please see the Wireless Data Services User’s Guide.
www.mot.com/iDEN
48
Page 57
Setting Programming Menus
Setting Programming Menus
You can customize the settings on your phone using the Programming Menu.
1. Press
2. Select “Prgm”.
3. Select “Ok”.
4. Press
n until you see “Prgm” on the display.
l or r to scroll to the desired Programming Menu Option or enter
the number of the Option.
NOTE: You can press *, #, and the n the correspondin g keypad number
to get to the desired programming menu.
Table 6: Programming Menu Options
Keypad
Number
Menu Option Function
1 Own Ph # Automatically store the telephone
2 Own Pvt ID Display the private number of
3 Mail Display Turn on and off the New Mail
4 Manual Lock:Off Lock your phone to prevent
5 Auto Lock:Off Automatically lock your phone
6 Auto Answer:Off Turn on or off automatic
number of your phone after you
receive the first incoming call
(Line1). You can also enter the
number and view it.
your phone.
message that is displayed with
incoming Voice, Message, or Net
Mail.
unauthorized use. You must enter
a pass code to unlock it.
each time it is powered on to
prevent unauthorized use.
answering of incoming phone
calls after 1-4 rings.
49
Page 58
Table 6: Programming Menu Options (Continued)
Keypad
Number
Menu Option Function
9 Vibrate Alert:Off Receive a non-audible alert for
10 Last Call Timer Display the duration of the most
11 Display Timer:Off Turn on or off automatic display
12 Reset Timer Display cumulative airtime of all
13 Total Timer Display cumulative airtim e of all
14 1 Minute Beep:Off Automati cally signal each minu te
15 Alert Receipt Delay Voice Mail and Me ssage
incoming phone and circuit data
calls and messages. See
“VibraCall® Alert” on page 15.
recent phone call.
of the Last Call Timer at the end
of each phone call.
phone calls since last reset.
phone calls.
of elapsed phone airtim e with an
audible beep.
Mail Alerts so that users are not
interrupted by the aler t t on e while
on a call. Users can choose to:
Delay All Alerts; Receive All
Alerts; Receive Message Mail
Alerts only. See “Alert Receipt
During Phone Cal l” on page 45.
16 Backlight Timer Specify the duration of the
20 Phone/Prvt List Add phone and private numbers in
www.mot.com/iDEN
Backlight Timer (0, 10, 20, or 30
seconds).
one procedure . See “Combined
Phone Number and Private ID
List” on page 22.
50
Page 59
Setting Programming Menus
Table 6: Programming Menu Options (Continued)
Keypad
Number
Menu Option Function
21 Phone List Edit Edit and erase up to 100
22 Prvt ID List Edit Edit and erase up to 100 Private
23 Talkgrp List
Program
24 Area List Program Add/Edit/Erase numbers and
25 Talkgrou p Mode
List Program
26 Status Message
List Programming
30 Ringer Volume Set the ringer volume using the
frequently called phone numbers
and associated names. See
“Editing and Erasing Phone List
Entries” on page 24.
numbers an d as sociated name s .
See “Editing and Erasing Private
ID List Entries” on page 25.
Add/Edit/Erase numbers and
associated names for up to 100
pre-programmed ta lkgroups. See
“Adding and Stori ng a
Talkgroup” on page 32
associated names for up to 50
targeted areas.
Add/Edit/Erase numbers and
associated names for up to 30 preprogrammed talkgroup modes.
Add/Edit/Erase numbers and
associated names for up to 10
alphanumeric Status Messages.
volume control keys, or lower the
volume to silence the ringer. See
“Setting the Ringer Volume” on
page 16.
31 Set Ring Styl e Select a distinct ring style for
incoming phone calls. See
“Setting a Ring Style for the
Alternate Line” on page 16.
51
Page 60
Table 6: Programming Menu Options (Continued)
Keypad
Number
Menu Option Function
32 Mail Volume Set the volume of incoming
33 Earpiece Volume Set the default earpiece volume
34 Keypad Volume Set the volume of the keypad
35 Speaker Volume Temporarily adjust the Group/
36 Spkr Vol Set Tone Turn the speaker volume set tones
37 Set Alert Style Select a distinct Call Alert tone.
38 Silent Group Silence all incomin g Group call
Message Mail, Voice Ma il, and
Net alert tones using the volume
control keys, or lower the volume
to silence the mail alert tones.
using the volume control keys.
tones using the volume control
keys, or to silence the key pa d
tones.
Private Sp ea k er volume for noisy
environments.
on or off.
See “Selecting a Call Alert Tone
Style” on page 29.
alerts and voi c e a ct ivity. When
set, your screen displays the
message, Group-Silent.
40 Change Passcode Change your secret four-digit pass
60 Set Baud Rate Set the modem baud rate between
61 Data Ring Volume Set the default data ring e r v olum e
www.mot.com/iDEN
code from the initial setting 0000.
the phone and the PC. See the
Wireless Data Services User’s
Guide.
using the volume control buttons.
See the Wireless Data Services
User’s Guide.
52
Page 61
Setting Programming Menus
Table 6: Programming Menu Options (Continued)
Keypad
Number
Menu Option Function
62 Pgm Data # View your circuit data (fax)
63 IP Address Use the scroll keys to view the
64 Reset KBytes Tx/
Rx
65 Lines per Screen
(Browser and Mail
menu)
70 Language Select one of four languages for
71 Time/Date Select the format for the time and
number. See the Wireless Data
Services User’s Guide.
Internet Protocol ( IP) Address-1
for your browser, as programmed
in your phone.
If your phone is cabled to a
computer, view IP Address-2, the
stored IP address of your
computer.
See the Wireless Data Services
User’s Guide.
View the number of Kilobytes
sent and received for packet data.
See the Wireless Data Services
User’s Guide.
View the display in 4 lines, 12
characters or 6 lines, 16
characters.
your display text. The default is
English. See “Changing the
Display Language” on page 11.
date display. See “Setting the
Time and Date” on page 9.
NOTE: Important! Do not perform the following shaded me nu opti ons unless
you are instructed to do so by your carrier. You could damage your
phone.
53
Page 62
Table 7: Other Programming Menu Options
Option
Number
41 Feature Reset Returns all feature settings to
42 Master Clear Performs Feature Reset and
43 Master Reset Resets the phone’s identification
44 Change Service
50 NAM Selects alternate Numeric
51 Networ k I D Edits the pre-programmed
Menu Option Function
their original defaults.
erases all stored lists.
number.
Key
Changes or resets the fraud
prevention service key.
Assignment Module (NAM).
See local carrier for information.
Network number list and selects
roaming options.
About Error Codes
You may receive operational status messages under certain conditions. Before
contacting your carrier, note the message, numeric code, and the conditions
under which it appeared. Table 8 lists and describes the operational status
messages.
Table 8: Error Codes
Status Messages Message Description
Number Not in Service The number that you entered is not
User Not Available The party that you called is either
www.mot.com/iDEN
valid.
busy, out-of-r ange, or turned off.
Please try again later.
54
Page 63
Setting Programming Menus
Table 8: Error Codes (Continued)
Status Messages Message Description
User Not Authorized The party that you called has not
Please Try Later This service is temporarily not
User Busy in Private The party that you call ed is busy
Service Restricted This service was restricted by your
Service Not Available This feature is not available on the
System Busy Try Later The system is experiencing heavy
Service Conflict This service cannot be e nabled
Please Try Again An error occurred. Note the error
User Busy in Data The party that you called is busy
Self Check Error A fault was detected with your
purchased this service.
available. Please try again later.
in a Private call.
carrier or it was not purchased.
current network.
traffic. Please try again later.
because an incompatible service
has already been turned on.
code and try again.
in a data call.
phone. If this error recurs, note the
error code and contact your
carrier.
Self Check Fail An operational fault was detected
with your phone. Note the nu meric
code, turn your p hone off, and
contact your carrier immediately.
55
Page 64
Optional Accessories
Batteries
NOTE: For best results, charge the batteries within the temperature range of
10
° C to 40° C (50° F to 104° F).
NOTE: Prolonged charging is not recommended. See T able9 for battery charg-
ing guidelines.
Charging the Battery
To get the maximum use from the battery, charge it overnight before you use it
for the first time. See Table 9 for battery charging times.
Table 9: Battery Charging Times
Motorola Battery Charging
Time to 90%:
Kit Number Description
Chemistry
NTN9037 Ni MH 100 minutes
NTN9038 Intrinsically
Safe
*
NiMH
Rapid
Charger
100 minutes
* For users who work in hazardous environments,
Intrinsically Safe Battery, NTN9038, is offered.
Please contact your carrier for availability and the
specific environments approved for this battery.
Battery Operating Instructions
• Extreme temperatures will degrade bat te ry p erf orm a nce . Do n ot store yo ur
battery where temperatures exceed 60°C (140°F) or fall below -20°C (4°F).
• The battery capacity will be degraded if stored for long perio ds whil e fully
charged. If long term storage is required, store at half capacity.
• For optimal battery life, use a Motorola iDEN approved NiMH Charger
with your Motorola iDEN NiMH battery. Other chargers may not fully
charge your NiMH or may yield a reduced number of charge cycles.
www.mot.com/iDEN
56
Page 65
Optional Accessories
Rapid Travel Charger
Using the NTN9035 Rap i d Tra ve l Cha r ge r, you can charge a battery from an
electrical outlet.
Accessory Connector
Rapid Travel Charger
Figure 2. Using the Travel Charger
Using the Ra pid Travel Charger (110V/220V/240V)
1. While holding the r750plus phone with its front facing you, insert the
accessory connector (with the Motorola logo facing you) into the slot on
the bottom of the r750plus phone until you hear a click.
2. Insert the Rapid Travel Charger transformer into an AC wall outlet. The
power light (green LED) on the accessory power supply will come on.
Rapid Travel Charger Operating Specifications
Input voltage range: 110V/220V/240V.
Operating temperature range: 0°C to +50°C.
57
Page 66
Vehicular Bat tery Ch arg er
The NTN9034 Vehicular Battery Charger enables in-vehicle communications
by charging the NiM H battery and providin g power to your r750plus phone.
The power light (green LED) will light when the Vehicular Battery Charger is
receiving power.
Accessory Connector
Figure 3. Using the Vehicular Battery Charger
Using the Vehicular Battery Charger
1. Attach the Vehicular Battery Charger’s accessory connector to the bottom
of the r750plus phone. While holding the r750plus phone with its front
toward you, insert the accessory connector (with the Motorola logo facing
you) into the slot on the bottom of the r750plus phone until you hear a
click.
2. Remove the vehi cle’s ciga rette ligh ter plug from the ciga rette lighte r receptacle.
3. Plug the Vehicular Battery Charger into the cigarette lighter receptacle.
The power light (green LED) will turn on.
4. The r750plus phone may be turned off, turned on, or in use.
Removing the Vehicular Battery Charger
1. Unplug the Vehicular Battery Charger from the vehicle’s cigarette lighter
receptacle.
2. Press the buttons on the accessory connector and pull the accessory connector from the bottom of the r750plus phone.
Operating Specifications
Operating voltage range: 10.8 - 33.0 Vdc.
Operating temperature range: -30°C to +60°C
www.mot.com/iDEN
58
Page 67
Optional Accessories
Desktop Dual-Pocket Charger
The NTN9036 Desktop Dual-P ocket Charger charges Motorola authorized
batteries, as listed on Page 56, for the r750plus phone.
Alignment rails
LED indicators
Pin charge contacts
Front pocket – phone with Battery
Figure 4. Desktop Dual-Pocket Charger
Rear pocket
– Battery only
Power supply cord receptacle
(DC jack)
Charging a battery
1. Plug the power supply DC jack into the receptacle in the back of the Desktop Dual-Pocket Charger.
2. Plug the transf or mer end of the power-supply cord into any standard AC
wall outlet.
3. Insert an r750plus phone with an attached ba tt ery, into the charger’s front
pocket. To do this, align the slots on the sides of the battery with the rails
on the sides of the charger pocket. Make sure the metal contacts on the
back of the battery are in contact with the charger contacts.
4. If the r750plus phone is properly seated in the front pocket, the charger’s
front pocket LED indicator will light.
5. The charger has th e capabil ity of displayin g the battery’s charge status. The
indicator will show the following: solid red=1- 30%; solid yellow=31 60%; flashing green=61 - 90%; solid green=91 - 100%.
NOTE: Charging times may vary when performing data operations.
Data Operation
1. Insert the flat end of the iDEN Data Cable (F LN9581A) into the phone’s
bottom Accessory connector.
2. Connect the opposite end of the data cable to the PC.
59
Page 68
Inserting and removing a battery from the rear pocket
Insert Remove
1
2
Figure 5. Adding and Removing a Battery from the Rear Pocket
1. Insert the battery with the Motorola label facing forward. To do this, align
the sides of the battery with the charger rails.
2. Make sure the metal contacts on the back of the battery are in contact with
the charging contacts.
3. To remove the battery, pull it up and out of the Charger.
NOTE: If a battery is in the rear pocket, and the phone with a battery is
inserted into the front pocket, the battery in the front pocket will
charge to full capacity before the battery in the rear pocket is charged.
The LED for the rear pocket flashes yellow, indicating that its battery is
waiting to be charged.
NOTE: To remove the batter y from the rear pocket, hold the base of the
charger and pull the battery up.
Desktop Charger Status
The Charger displays the battery’s charge status . The in dica to r will show on e of
the following:
solid red =1-30%; solid yellow =31-60%; flashing green =61- 90%; solid green
=91-100%.
Desktop Charger Troubleshooting
If the battery is not charging and you see:
Flashing yellow indicator -
• The flashing yellow LED is used to indicate that th e Charger’s
pocket is in a wait state.
• If a battery is in the rear pocket, the rear pocket’s LED continues to
flash yellow until the battery in the front pocket is more than 90%
charged (front pocket’s LED is solid green). This is normal
operation.
• To protect your battery’s life expectancy, the Charger does not rapid
charge a battery when its temperature is below 5
www.mot.com/iDEN
60
o
C (41oF) or above
Page 69
45oC (113oF).
No LED indication -
• Check that the r750plus phone with battery, or a battery alone, is
inserted correctly.
• Make sure that the power supply is plugged in to an appropriate AC
outlet and that the connector is properly seated.
• Rear pocket onl y: Remove the battery from t he Charger. Use an
ordinary pencil eraser to clean the three metal contacts on the
battery and then place the battery in the Charger.
• If the LED indicator remains turned OFF, the battery may be
defective and should be replaced.
Flashing red LED indicator -
• Remove the battery from the Charger. Use an ordinary pencil eraser
to clean the three metal contacts on the battery and then place the
battery in the Charger.
• If the LED indicator remains turned OFF, the battery may be
defective and should be replaced.
Both LEDs flash red -
• This indicates that the incorrect power supply is plugged in.
Optional Accessories
61
Page 70
Audio Adapter
The FLN2854A Audio Adapter con nects an earpiece microphone or headset to
your r750plus phone for privacy and hands-free operation.
The Audio Adapter fits onto the bottom of the r750plus phone and provides a
standard 2.5mm jack connection for an ear piece microphone or headset.
The following audio accessories are compatible with the audi o adapter:
• Earpiece wit h Microphone (NTN8367)
• Headset with Boom Microphone (NTN8513)
• Lightweight Headset with Microphone (NTN8496)
• Over-the-Ear S tyle Headset (NTN8497 )
Audio Adapter
Release
Button
Connector
Release
Button
2.5mm jack
Figure 6. Using the Audio Adapter
Using the Audio Adapter
1. Hold the phone and the Audio Adapter facing you so that you s ee t he
Motorola logo on the adapter.
2. Insert the Audio Adapter’s connector into the r750plus phone Bottom
Accessory Connector. You will hear the connector snap into place.
NOTE: When the audio adapter and ear pie ce or headset are connected, all
audio, including tones, will be routed to the audio accessory’s earpiece.
Attaching/Detaching the Earpiece Microphone or Headset
1. Insert the 2.5mm plug of the earpiece mic rophone or headset cord into the
jack of the Audio Adapter.
2. Pull on the plug, not on the cord, to remove the earpiece
microphone.
62
www.mot.com/iDEN
Page 71
Optional Accessories
Removing the Audio Adapter
1. Simultaneously press the release buttons located on either side of
the Audio Adapter and pull the Audio Adapter from the r750plus
phone.
Battery Belt Clip
The HLN9844A Battery Belt Clip provides a convenient means by which to
carry your r750plus phone with you.
Belt Clip Tab
Battery (partial view)
Figure 7. Battery Belt Clip
Using the Battery Belt Clip
1. Slide the belt clip i nto th e ba c k of th e ba tte ry (pu sh u n til th e c lip loc k s into
place).
2. Clip the r750plus phone to your belt .
3. To remove the clip from the battery, push the holder tab outward and slide
the clip out of the battery.
NOTE:A small flathead screwdriver is recommended to push the holder tab
outward when removing the clip.
Leather Carry Case
• The FLN9580A Leather Car ry Case pr otect s your r750plus phone while on
the go
• Includes a leather bel t clip for easy attachment to a belt or purse
*
*Remove the belt clip from the phone before inserting it into the
leather case.
63
Page 72
• Accommodates most r750plus phone accessories including travel chargers,
audio accessories, vehi cle accessories, and data accessories.
Hard-Install Car Kit
NOTE: The FLN2570A Hard-Install Car Kit enables in-vehicle communica-
tions by providing extended RF coverage, the abi li ty to c onne ct to 12Vdc or 24-Vdc power sources, data interface, and the ability to rapidcharge the battery.
The FLN2570A includes:
• Visor Microphone
• Remote PTT
• External 4-watt Speaker
• Phone Coupler
• Junction Box.
An external Push-To-Talk (PTT) button is also included. When the phone is
turned off, the Hard-Install Car Kit ch arges the Stand ard battery in 75 minu tes to
90% capacity. Charging time will be longer if the phone is operational during
charge time.
64
Figure 8. Hard-Install Car Kit
www.mot.com/iDEN
Page 73
Optional Accessories
Remote Speaker/Microphone
The FLN2800A Remote Speaker/Microphone (RSM) provides a convenient
means of communicatin g by having a speaker, a microphone, and a Push-toTalk (PTT) button in a single, h and-held or clip-on accessory. The RSM also
includes a 3.5 mm audio jack (located on the opposite side of the PTT) to accept
secondary receiver audio accesso ries.
PTT Button 3.5mm Audio Jack
Speaker /
Microphone
Accessory
Connector
Attaching and Removing the Swivel Clip
To attach the swivel clip to the remote speaker/
microphone:
1. Position the clip with the release tab pointing
upward and align the metal plat e edges of the
swivel clip with the plastic slots on the RSM’s rear
housing.
2. While holding the clip open, slide the metal plate
in and push down firmly until the parts snap
together.
To remove the swivel clip from the remote speaker/
microphone:
1. Carefully pus h the fla t bla de of a #2 slotted screwdriver (or similar instrument) between the RSM’s
housing and the swivel clip’s metal release tab, as
shown in the figure.
2. While performing step 1, push the swivel clip toward the top of the RSM.
3. As the release ta b disengages, remove th e screwdriver and pull the swivel
clip completely away from the unit.
Connecting the Remote Speaker/Microphone to the Portable
To attach the accessory connector, position the portable so that it faces you.
65
Page 74
1.Position the accessory connector so that its
coiled cord extends from the bottom of the portable and its latch is on your left.
2.Insert the RSM’s accessory connector into the
bottom of the portable (push both ta bs on the
accessory connector when inserting into the portable).
3.Push the accessory connector firmly against
the portable to make sure it is held in place.
4.Attach the smaller end of the cable-rest raint
clip on the straight portion of the coiled cord.
5.Attach the larger end of the cable-restraint clip
to the base of the antenna.
6. Adjust the cord length in the smaller end of the cable restraint clip until it is
comfortable.
Operation
Please read the safety information cont ai ne d in the use r’s guide supplied with
the portable before operating this equipment.
The remote speaker/microphone (RSM) only operates when the portable is in
the voice-dispatch mode (group or private call).
Wearing the RSM
For optimum performance from your RSM, wear the radio
and RSM so that the accessory cord will not cross over or
touch the ante nna. Also, try to wear the radio and
accessory combination fairly close to each other to avoid
strain on the accessory connector.
Receiving:
When the RSM is connect ed to the radio’s bottom accessory conn ector, the
radio’s speaker is muted, and the audio is on ly heard from the RSM speaker.
Similarly, when a second ary receiver audio accessory is plugged into the 3.5
mm audio jack, audio to the RSM is rerouted to the secondary accessory.
Transmitting:
Connecting the remote speaker/microphone to the radio does not disable the
radio’s microphone and PTT button.
www.mot.com/iDEN
66
Page 75
Safety and General Informati on
Safety and General Information
IMPORTANT INFORMATION ON SAFE AND
EFFICIENT OPERATION.
READ THIS INFORMATION BEFORE USING
YOUR INTEGRATED MULTI-SERVICE
PORTABLE RADIO.
RF Operational C hara cteri stics
Your radio product contains a radio frequency transmitter to convey the
information you wish to send as well as occasional automatic signals used to
sustain connection to the wireless network, and a receiver which enables you to
receive communication and connection information from th e network.
Exposure To Radio Frequency Energy
Your Motorola Radio Product is designed to comply with the following nation al
and international standards and guidelines regarding exposure of h uman beings
to radio frequency electromagnetic energy:
• United Stat es Federal Communications Commission, Code of Federal
Regulations; 47 CFR part 2 sub-part J
• American National Standards Institute (ANSI) / Institute of Electrical and
Electronics Engineers (IEEE). C95. 1-1992
• Institute of Electrical and Electronics Engineers (IEEE). C95. 1-1999
Edition
• National Council on Radiation Protection and Measurements (NCRP) of
the United States, Report 86, 1986
• International Commission on Non-Ionizing Radiation Protection (ICNIRP)
1998
• National Radiological Protec tio n Boa rd of the Unite d K ing do m , 199 5
• Ministry of Health (Canada ). Sa fety Cod e 6. Limits of Huma n Expos ure to
Radiofrequency Electromagnetic Fields in the Frequency Range from 3
kHz to 300 GHz, 1999.
• Australian Communications Authority Radiocommunications
(Electromagnetic Radiation - Human Exposure) Standard 1999 (applicable
to wireless phones on ly)
To assure optimal radio product performance and make sure human exposure to
radio frequency electromagnetic energy is within the guidelines set forth in the
above standards, always adhere t o t he fol l owing procedures:
67
Page 76
Portable Radio Product Operation and EME Exposure
Antenna Care
Use only the suppli e d or an approved antenna. Unauthorized replacement
antennas, modificati ons, or attachments could d amage the phone and may
violate FCC regulations.
DO NOT hold the antenna wh en the ra dio product is “IN USE”. Holdi ng the
antenna affects call quality and may cause the radio product to operate at a
higher power level than needed.
Phone Operation
When placing or receiving a phone call, or using the group and private call
functions with a Group/Private Speaker OFF (muted speaker icon visible in th e
display), hold you r radio pr od u ct as yo u wo uld a wireline telephone. Speak
directly into the microphone.
Two-way radio operation
When using your radio product as a traditional two-way
radio while making group or private calls with the Group/
Private Speaker ON (no speaker icon visible in the display),
hold the radio product in a vertic al position with the
microphone one to two inches (2.5 to 5 cm) away from
the lips.
Body-worn operation
To maintain compliance with FCC RF exposure guidelines, if you wear a radio
product on your body when transmitting, always place the radio product in a
Motorola approved clip, h ol der, holster, case, or body harness for this
product. Use of non-Motorola-approved accessories may exceed FCC RF
exposure guidelines. If you do not use a Motorola approved body-worn
accessory and are not using the radio product in the intended use positions along
side of the head in the phone mode or in front of the face in the tw o-way radio
mode then ensur e the antenna and the radio is kept the following minimum
distances from the body:
• Phone or Two-way radio mode: one inch (2.5 cm)
• Data operation using any data feature with or without an
accessory cable : two inches (5 cm)
www.mot.com/iDEN
68
Page 77
Safety and General Informati on
Approved Accessories
For a list of approved Motorola accessories c all 1-800-453-0920, visit our
website at www.mot.com/iden, or look in the accessory section of th is manual.
THIS MODEL PHONE MEETS THE GOVERNMENT’S REQUIREMENTS FOR
EXPOSURE TO RADIO WAVES.
Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to
exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal
Communications Commission of the U.S. Government. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy for the general population. The guideli nes
are based on standards that were developed by independent scientific organizations through
periodic and thorough evaluation of scientific studies. The standards include a substantial safety
margin designed to assure the safety of all persons, regardless of age and health.
The exposure standard for wireless mobile phones employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
conducted using standard operating positions specified by the FCC with the phone transmitting at
its highest certified power level in all tested frequency bands. Although the SAR is determined at
the highest certified power level, the actual SAR level of the phone while operating can be well
below the maximum value. This is because the phone is designed to operate at multiple power
levels so as to use only the power required to reach the network. In general, the closer you are to a
wireless base station antenna, the lower the power output.
Before a phone model is available for sale to the public, it must be tested and certified to the FCC
that is does not exc eed the limit established by the government-a dopted requirement for safe
exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body)
as required by the FCC for each model. The highest SAR value for this model phone when tested
for use at the ear is 0.48 W/kg and when tested on the body, as described in this user guide, is 0.59
W/kg during voice transmission using Phone Mode and 1.35W/kg during packet data
transmission. (Body-worn measurements differ among phone mo dels, depending upon available
accessories and FCC requirements.) While there may be differences between the SAR levels or
various phones and at various positions, they all meet the government requirement for safe
exposure.
The FCC has granted an Equipment Au thorization for this model phone with all reported SAR
levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this
model phone is on file with the FCC and can be found und er the Display Grant section of http ://
www.fcc.gov/oet/fccid after searching on FCC ID AZ489FT5800.
Additional information on Specific Absorption Rates (SAR) can be found on the Cellular
Telecommunications Industry Association (CTIA) web-site at http://www.wow-com.com.
______________________________________
* In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6
watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin
of safety to give additional protection for the public and to account for any variations in
measurements.
*
Tests for SAR are
Electro Magnetic In terf erenc e/ Comp at ibili ty
NOTE: Nearly every electronic device is susceptible to electromagnetic
interference (EMI) if inadequately shield ed, designed or otherwise configured
for electromagnetic compatibility.
69
Page 78
Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off
your radio product in any facility where posted notices instruct you to do so.
Hospitals or health care facilities may be using equipment that is sensitive to
external RF energy.
Aircraft
When instructed to do so, turn off your r adi o p r od uc t when on board an ai rc r af t.
Any use of a radio product must be in accordance with applicable regulations
per airline crew instructions.
Medical Devices
Pacemakers
The Health Industry Manufacturers Asso ci ation recommends that a minimum
separation of 6 inches (15 cm) be ma intain ed between a h andhe ld wireless radio
product and a pacemaker. These recommendations are consistent with the
independent research by, and recommendations of, Wireless Technology
Research.
Persons with pacemakers should:
• ALWAYS keep the radio product more than 6 inches (15 cm) from their
pacemaker when the radio product is turned ON.
• Not carry the radio product in a breast pocket.
• Use the ear opposite the pacemaker to minimize th e potential for
interference.
• Turn the radio product OFF immediately if you have any reason to suspect
that interference is taking place.
Hearing Aids
Some digital wireless radio products may interfere with some hearing aids. In
the event of such inter ference, you may want to consult your hearing aid
manufacturer to discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult the man ufacturer of your
device to determine if it is adequately shielded from external RF energy. Your
physician may be able to assist you in obtaining this information.
www.mot.com/iDEN
70
Page 79
Safety and General Informati on
Use While Driving
Check the laws and regulations on t he use of radio products in the area where
you drive. Always obey t hem.
When using the radi o product while driv ing, please:
• Give full attention to driving and to the road
• Use hands-free operat ion, if available.
• Pull off the road and park befo re making or answering a call if driving
conditions so require.
.
71
Page 80
!!
Operational Warnings
For Vehicles Equipped with an Air Bag
Do not place a portable radio product in the area ov er the air bag or in the
air bag deployment area. An air bag inflates with great force. If a portable
radio is placed in the air bag deployment area and the air bag inflates, the
radio product may be propelled with great force and cause serious injury to
occupants of the ve hic l e .
Potentially Explosive Atmospheres
Turn off your radio product, prior to entering any area with a potentially
explosive atmosphere, unless it is a radio product type especially qualified
for use in such areas (for example, Factory Mutua l Ap proved). Do not
remove, install, or charge batte r ies in such areas. Sparks in a potentially
explosive atmosphere can cause an explosion or fire resulti ng in bodily
injury or even death.
NOTE: The areas with po tentially explosive a tmospheres referred to
above include fueling areas such as below d eck s on b oa t s , fu el or
chemical transfer or storage facilities, areas where the air contains chemicals or particles, such as grain, dust or metal powders,
and any other area where you would normally be advised to turn
off your vehicle engine. Areas with potentially explosive atmospheres are often but not always pos ted.
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your radio
product when you are near electrical blasting caps, in a blasting area, or in
areas posted: “Turn off two-way radio”. Obey all signs and instructions.
72
www.mot.com/iDEN
Page 81
Safety and General Informati on
!
C a u t i o n
Operational Cautions
Antennas
Do not use any portable radio product that has a damaged antenna. If
a damaged antenna comes into contact with yo ur skin, a minor burn can
result.
Batteries
All batteries can cause property damage and/or bodily injury, such as burns
if a conductive material such as jewelry, keys, or beaded chains touches
exposed terminals. The conductive material may complete an electrical
circuit (short circuit) and become quite hot. Exercise care in handling any
charged battery, particularly when placing it inside a pocket, purse, or other
container with metal objects.
When the battery is detached from the phone, your batteries are packed
with a protective battery cover. Please use this cover for storing your
batteries when not in use.
Cleaning and Drying Considerations
Using a leat her c arr y cas e ma y he lp p rotec t the su rfa ces a nd help pr event liquid s
(e.g., rain) from entering into the interior of the radio product. This product is
not water proof, and exposing the unit to liquids may result in permanent
damage to the unit.
If your radio product interior gets wet, then do n ot try to accelerate drying with
the use of an oven or a dryer as this will damage the radio product and void the
warranty. Instead, do the following:
1. Immediately power off the radio product.
2. Remove Batter y from radio product.
3. Shake excess liquid from phone.
4. Place phone and battery in an area that is at room temperature and has good
air flow.
5. Let phone and battery dry for 72 hours before reconnecting the battery and/
or powering on the pho ne.
73
Page 82
If the phone does not work after following the steps listed above, contact your
dealer for servicing information.
Clean the external surfaces of the radio product with a damp cloth, using a mild
solution of dish washing detergent and water. Some househol d cleaners may
contain chemicals that could seriously damage the radio product. Avoid the use
of any petroleum-bas e d s olv e nt cle a n ers . A ls o, avo id ap plying liquids directly
on the radio product.
74
www.mot.com/iDEN
Page 83
Intrinsicall y Sa fe Radi o In for m a ti o n
Intrinsically Safe Radio
Information
FMRC Approved Equipment
Anyone intending to use a radio in a location where hazardous concentrations of
flammable material exist (hazardous atm osphere) is advised to become familiar
with the subject of intrinsic safety and with the National Electric Code NFPA 70
(National Fire Protection Association) Article 500 (hazardous [classified]
locations).
An Approval Guide, issued by Factory Mutual Research Corporation (FMRC),
lists manufacturers and the products approved by F MRC for use in such
locations. FMRC has also issued a voluntary appro val st andard for repair
service (“Class Number 3605”).
FMRC Approval labels are att ached to th e radio to ide ntify the uni t as bein g FM
Approved for specified hazardous atmospheres. This label specifies the
hazardous Class/Division/Group along with the part number of the battery that
must be used. Depen ding on the design of th e porta ble un it, th is FM la bel c an be
found on the back of the radio housing or the bottom of the radio housing.Their
Approval mark is shown below.
FM
APPROVED
75
Page 84
!
!
W A R N I N G
Do not operate radio communications equipment in a hazardous
atmosphere unless it is a type especially qualified (e.g. FMRC Approved)
for such use. An explosion or fire may result.
Do not operate the FMRC Approved Product in a hazardous atmosphere if
it has been physically damaged (e.g. cr acked housing). An expl osion or
fire may result.
Do not replace or charge batteries in a hazardous atmosphere. Contact
sparking may occur while installing or removing batteries and cause an
explosion or fire.
Do not replace or change accessories in a hazardous atmosphere. Contac t
sparking may occur while installing or removing accessories and cause an
explosion or fire.
Do not operate the FMRC Approved Prod uct unit in a hazardous location
with the accessory contacts exposed. Keep the connector cover in pla ce
when accessories are not used.
Turn radio off before removing or installing a battery or accessory.
Do not disassemble the FMRC Approved Product unit in any way that
exposes the internal electrical circuits of the unit.
Radios must ship from the Motorola manufacturing facility with the hazardous
atmosphere capability and FM Approval labeling. Radios will not be
“upgraded” to this capability and labeled in the field.
A modification changes the unit’s hardware from its original design
configuration. Modifications can only be done by the original product
manufacturer at one of its FMRC audited manufacturing facilities.
www.mot.com/iDEN
76
Page 85
Intrinsicall y Sa fe Radi o In for m a ti o n
!
!
W A R N I N G
Failure to use an FMRC Approved Produ ct un it with an FMRC Ap pro ved
battery or FMRC Approved accessories specifically approved for t hat
product may result in the dangerously unsafe condition of an unapproved
radio combination being used in a hazar dous location.
Unauthorized or inc orrect m odifi cation of an FM RC Ap proved Produc t unit wi ll
negate the Approval rating of the product.
Repair of FMRC Approved Products
REPAIRS FOR MOTOROLA FMRC APPROVED PRODUCTS
ARE THE RESPON SIBILITY OF THE USER.
You may want to c o nsid er u sing a rep air fa c ilit y that operates under 36 05 re p ai r
service approval.
!
!
W A R N I N G
Incorrect rep a ir or relabeling of any FMRC Approved Product unit coul d
adversely affect the Approval rating of the unit.
Use of a radio that is not intrinsically safe in a hazardous atmosphere could
result in serious injury or death.
FMRC’s Approval Standard Class Number 3605 is subject to change at any time
without notice to you , so yo u ma y want to obtain a current copy of 3605 fro m
FMRC. Per the December , 1994 publication of 3605, some key definitions and
service requirements are as follows:
Repair
A repair constitutes something done internally to the unit that would bring it
back to its original conditio n Approved by FMRC. A repai r should be done in an
FMRC Approved facility.
Items not considered as repairs are those in whi ch an action is performed on a
unit which does not re quire th e oute r casi ng of the unit to be opened in a manner
77
Page 86
which exposes the internal electrical circuits of the unit. You do not have to be
an FMRC Approved Repair Facility to perform these actions.
Relabeling
The repair facility shall have a method by which the replacement of FMRC
Approval labels are controlled to ensure that any relabeling is limited to units
that were originally shipped from the Manufacturer with an FM Approval label
in place. FMRC Approval labels shall not be stocked by the repair facility. An
FMRC Approval label shall be ordered from the original manufacturer as
needed to repair a specific unit. Replacement labels may be obtained and
applied by the repair facility providing satisfactory evidence that the unit being
relabeled was originally an FMRC Appro ved unit. Verifica tion may in clude, but
is not limited to: a unit with a damaged Approval label, a un it with a de fect ive
housing displaying an Approval label, or a customer inv oice indicating the serial
number of the unit and purchase of an FMRC Approved model.
Do Not Substitute Options or Accessories
The Motorola communications equipment certified by Factory Mutual is tested
as a system and consist s of the FM Approved portable, FM Approved bat tery,
and FM Approved acc ess o ri e s or op tio ns , or both. This Approved portable and
battery combination must be strictly observed. There must be no substitution of
items, even if the substitute has been previously Approved with a different
Motorola communicati ons equipment unit. Approved configurations are listed
in the FM Approval guide published by FMRC, or in the product FM
Supplement. T h is FM Supplement is shipped with FM Appr oved radio and
battery combination from the manufacturer. The Approval guide, or the
Approval st anda rd Cla ss Nu mb er 36 05 doc ume nt for repa irs and serv ice, ca n be
ordered direc tl y through Factory Mutual Research Corpor ation located in
Norwood, Massachusetts.
78
www.mot.com/iDEN
Page 87
Accessory Safety Information
Accessory Safety Information
IMPORTANT: SAVE THESE ACCESSORY SAFETY INSTRUCTIONS
• Before using any battery or battery charger , read all the instructions for and
cautionary markings on (1) the battery, (2) the battery charger, which may
include a separate wall-mounted power supply or tr ansformer, and (3) the
radio product using the battery.
• Do not expose any battery charger to water, rain, or snow as they are
designed for indoor or in-vehicle use only.
To reduce the risk of injury, charge only the rechargeable
batteries listed in the Accessories section of this manual.
!
!
W A R N I N G
• To reduce the risk of damage to the cord or plug, pull by the pl ug rather
than the cord when you disconnect the battery charger from the power
source outlet.
• Do not operate any battery charger with a damaged cord or plug - replace
them immediately.
• Battery chargers may become warm during operation, but not hot. If it
becomes hot to the to uc h , u nplug it from the power outlet imme dia te ly and
discontinue its use.
• Use of a non-recommended attachment to a battery charger may result in a
risk of fire, electric shock, or injury to persons.
• Make sure the battery charger power cord is located so that it will not be
stepped on, tripped over, or subjected to damage or s tress.
• An extension cord should not be used with any battery charger unless
absolutely necessary. Use of an improper extension cord could result in a
risk of fire and electric shock. If an extension cord must be used, make sure
that:
❒
The pins on the plug of the extension cord are the same num-
ber, size, and shape as those on the plug of the charger.
❒
The extension cord is properly wired and in good electrical
condition.
❒
The cord size is 18A WG for lengths up to 100 feet and 16 AWG
for lengths up to 150 feet.
• Do not operate any battery charger if it has received a sharp blow, has been
dropped, or has been damaged in any way; ta ke it to a qualified s e rvice
technician.
• Do not disassemble a battery charger; take it to a qualified service
technician when service or repair is requi r ed. Incorrect reassembly may
result in a risk of electric shock or fire.
• Maximum ambient temperature around the power supply or transformer of
any battery charger shou ld not exceed 40°C (104°F).
Other types of batteries may burst, causing personal inj ury
and damage.
79
Page 88
• The output power from the power supply or transformer must not exceed
the rating given on the Desktop Dual-Pocket Charger.
• The disconnection from the line voltage is made by unplugging the power
supply from the AC receptacle.
• To reduce ris k of ele ctric s hock, un pl ug any ba ttery c har ge r from th e outle t
before attempting any maintenan ce or clea ning .
• For optimum charging performance, turn off the radio product while
charging it in any battery charger.
80
www.mot.com/iDEN
Page 89
Warranty
Warranty
Limited Warranty Motorola Communi cation Products
NOTE: This Warranty applies within the fifty (50) united states and the Dis-
trict of Columbia.
I. What This Warranty Covers and For How Long:
MOTOROLA, INC. (“MOTOROLA”) warrants the MOTOROLA
manufactured iDEN Communication Products listed below (“Product”) against
defects in material and workmanship under normal use and service for a period
of time from the date of purchase as scheduled below:
iDEN Subscriber Digital Mobil e and
Portable U nits
Product Accessories One (1) Year
Batteries One (1) Year
Rechargeable Batteries will be replaced during the applicable warranty period
if:
a. the battery capacity falls below 80% of rated capacity, or
b. the battery develops leakage.
MOTOROLA, at its options, will at no charge either repair the Product (with
new or reconditioned parts), replace it (with a new or reconditioned Product), or
refund the purchase price of the Product during the warranty period provided it
is returned in accordance with the terms of this warranty. Replaced parts or
boards are warranted for the balance of the original applicable warranty period.
All replaced parts of Product shall become the property of MOTOROLA.
This express limited warranty is extended by MOTOROLA to the original end
user purchaser only and is not assignable or transferable to any other party. This
is the complete warranty for the Product manufactured by MOTOROLA.
MOTOROLA assumes no obligations or liability for additions or modifications
to this warranty unless made in writing and signed by an officer of
MOTOROLA. Unless made in a separate agreem ent between MOTOROLA and
the original end user purchaser, MOTOROLA do es not warra n t the installa tio n,
maintenance or serv ice of the Product.
MOTOROLA cannot be responsible in any way for any ancillary equipment not
furnished by MOTOROLA which is attached to or used in connection with the
Product, or for operation of the Product with any an cillary equipment, and all
such equipment if expressly excluded from this warranty. Because each system
One (1) Year
81
Page 90
which may use the Product is unique, MOTOROLA disclaims liability for
range, coverage, or operation of the syst em as a whole under this warranty.
II. General Provi sions:
This warranty sets forth the full extent of MOTOROLA’S responsibilities
regarding the Pr oduct, Repair, replacement or refund of the purchase price, at
MOTOROLA’S options, is the exclusive remedy. THIS WARRANTY IS
GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED
WARRANTIES, INLCUDING WITHOUT LIMITATION, IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE
FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE,
COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE
FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.
III. State Law Rights:
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATION ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY.
This warranty gives specific legal rights, and there may b e other rights which
may vary from state to state.
IV. How to Get Warranty Ser vice:
You must provide pro of of purchase (bearing the date of purchase and Produ ct
item serial number) in order to receive warranty service and, also, deliver or
send the Product item, transportation and insurance prepaid, to an authorized
warranty service location. Warranty service will be provided by MOTOROLA
through one of its authorized warranty service locations. If you first contact the
company which sold you the Product (e. g., dealer or communication service
provider), it can facilitate your obtaining warranty service. You can also call
MOTOROLA at 1-800-453-0920 for warranty service location information.
V. What This Warranty Does Not Cover:
a. Defects or damage resulting from use of the Product in other than its
normal and customary manner.
b. Defects or damage from misuse, accident, water, or neglect.
82
www.mot.com/iDEN
Page 91
Warranty
c. Defects or damage from improper testing, operation, maintenance,
installation, alteration, modification, or adjustment.
d. Breakage or damage to antennas unless caused directly by defects in
material workmanship.
e. A Product subjected to unauthorized Product modifications, disas-
semblies or repairs (including, without limitation, the addition to the
Product of non-MO TOROL A supplied equipment) which adversely
affect performance of the Product or interfere with MOTOROLA’S
normal warranty inspection and testing of the Product to verify any
warranty claim.
f. Product which has had t he serial number removed or made illegible.
g. Rechargeable batterie s if:
(1). Any of the seals on the battery enclosure of cells are broke n or shoe
evidence of tampering.
(2) The da mage or defect is caused by charging or using the ba ttery in
equipment or service other than the Product for which it is specified.
h. Freight costs to the repair depot.
i. A Product which, due to illegal or unauthorized alteration of the soft-
ware/firmware in the Product, does not function in accordance with
MOTOROLA’S published specifications or the FCC type acceptance
labeling in effect for the Product at the time the Product was initially
distributed fr om MO T O R O LA.
j. Scratches or other cosmetic damage to Product surfaces that does not
affect the operation of the Product.
k. Normal and customary wear and tea r.
VI. Patent and Software Provisions:
MOTOROLA will defend, at its own expense, any suit brought against the end
user purchaser to the extent that it is based on a claim that the Product or parts
infringe a United States patent, and MOTOROLA will pay those costs and
damages finally awarded against the end user purchaser in any such suit w hi ch
are attributable to any such claim, but such defense and payments are
conditioned on the following:
a. that MOTOROLA will be notified promptly in writing by such pur-
chaser of any notice of such claim;
b. that MOTOROLA will have sole control of the defense of such suit
and all negotiations for its settlement or compromise; and
c. Should the Product or parts become, or in MOTOROLA’S opinion b e
likely to become, the subject of a clai m of infringement of a United
States patent, that such purchaser will permit MOTO ROLA, at its
83
Page 92
option and expense, either to procure for such purch aser t he right to
continue to using the Produ ct or parts o r to repla ce or modify the same
so that it becomes non- infringing or to gra nt such purchaser a credit
for the Product or parts as depreciated and accept its return. The
depreciation will be an equal amount per year over the lifetime of the
Product or parts as established by MOTOROLA.
MOTOROLA will have no liability with respect to any claim of patent
infringement which is based upon the combination of the Product or parts
furnished here under with software, apparatus or devices not furnished by
MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary
equipment or software not furnished by MOTOROLA which is attached to or
used in connection with the Product or any parts thereof.
Laws in the Uni ted S tates and ot her coun trie s pres erv e for MOTO ROL A cert ain
exclusive rights for copyrighted MOTOROLA software, such as the exclusive
rights to reproduce in copies and di stribute copies of such MOTOROLA
software. MOTOROLA software may be used in only the Product in which the
software was originally embodied and such software in such Product may not be
replaced, copi ed, distributed, mod ified in any way, or used to product any
derivative thereof. No other use including, without limitation, alteration,
modification, r eproduction, distribution, or reverse engineering of such
MOTOROLA software or exercise or rights in such MOTOROLA software is
permitted. No license is granted by implication, estoppel or otherwise under
MOTOROLA patent rights or copyrights.
84
www.mot.com/iDEN
Page 93
Warranty
Limited Warranty Motorola Com mun icati on Produc ts
(Internation al )
NOTE:This Warranty applies within Singapore and the Philippines.
I. What This Warranty Covers and For How Long:
MOTOROLA warrants the MOTOROLA manufactured iDEN Communication
Products listed below (“Product”) against defects in material and workmanship
under normal use and service for a period of time from the date of purchase as
scheduled below:
iDEN Subscriber Digital Mobil e and
Portable U nits
Product Accessories One (1) Year
Rechargeable Batteries will be replaced during the applicable warranty period
if:
a. the battery capacity falls below 80% of rated capacity, or
b. the battery develops leakage.
MOTOROLA, at its options, will at no charge either repair the Product (with
new or reconditioned parts), replace it (with a new or reconditioned Product), or
refund the purchase price of the Product during the warranty period provided it
is returned in accordance with the terms of this warranty. Replaced parts or
boards are warranted for the balance of the original applicable warranty period.
All replaced parts of Product shall become the property of MOTOROLA.
This express limited warranty is extended by MOTOROLA to the original end
user purchaser only and is not assignable or tra nsferable to a ny other party. This
is the complete warranty for the Product manufactured by MOTOROLA.
MOTOROLA assumes no obligations or liability for additions or modifications
to this warranty unless made in writing and signed by an officer of
MOTOROLA. Unless made in a separate agreement between MOTOROLA
and the original end user purchaser, MOTOROLA does not warrant the
installation, maintenance or service of the Prod uc t.
MOTOROLA cannot be responsible in any way for any ancillary equipment not
furnished by MOTOROLA which is attached to or used in connection with the
Product, or for operation of the Product with any an cillary equipment, and all
such equipment if expressly excluded from this warranty. Because each system
which may use the Product is unique, MOTOROLA disclaims liability for
range, coverage, or operation of the system as a whole under this warranty.
One (1) Year
85
Page 94
II. General Provisions:
This warranty sets forth the full extent of MOTOROLA’S responsibilities
regarding the Pr oduct, Repair, replacement or refund of the purchase price, at
MOTOROLA’S options, is the exclusive remedy. THIS WARRANTY IS
GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED
WARRANTIES, INLCUDING WITHOUT LIMITATION, IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY TO THE FULL EXTENT SUCH MAY BE
DISCLAIMED BY LAW. IN NO EVENT SHALL MOTOROLA BE LIABLE
FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE,
COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE
FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.
III. How to Get Warranty Service:
You must provide pro of of purchase (bearing the date of purchase and Produ ct
item serial number) in order to receive warranty service and, also, deliver or
send the Product item, transportation and insurance prepaid, to an authorized
warranty service location. Warranty service will be provided by MOTOROLA
through one of its authoriz e d warranty service locations. If you first contac t th e
company which sold you the Product (e. g., dealer or communication service
provider), it can facilitate your obtaining warranty service.
IV. What This Warranty Does Not Cover:
a. Defects or damage resulting from use of the Product in other
than its normal and customary manner.
b. Defects or damage from misuse, accident, water, or neglect.
c. Defects or damage from improper testing, operation,
maintenance, installation, alteration, modification, or
adjustment.
d. Breakage or damage to antennas unless caused directly by
defects in material workmanship.
e. A Product subjected to unauthorized Product modifications,
disassemblies or repairs (including, without limitation, the
audition to the Product of non-MOTOROLA supplied
equipment)
86
www.mot.com/iDEN
Page 95
Warranty
f. Product which has had the serial number removed or made
illegible.
g. Rechargeable batteries if:
1.Any of the seals on the battery enclosure o f cells are broken o r
shoe evidence of tampering.
2.the damage or defect is caused by charging or using the
battery in equipment or service other than the Product for which
it is specified.
h. Freight costs to the repair depot.
i. A Product which, due to illegal or unauthorized alteration of
the software/firmware in the Product, does not function in
accordance with MOTOROLA’S published specifications or
the local type acceptance labeling in effect for the Product at
the time the Product was initially distributed from
MOTOROLA.
j. Scratches or other cosmetic damage to Product surfaces that
does not effect the operation of the Product.
k. Normal and customary wear and tear.
l. Exclusion for defects or damage arising from use of the
products in connection with non-MOTOROLA equipment.
V. Patent and So ftware Provisions:
MOTOROLA will defend, at its own expense, any suit brought against the end
user purchaser to the extent that it is based on a claim that the Product or parts
infringe a United States patent, and MOTOROLA will pay those costs and
damages finally awarded against the end user purchaser in any such suit w hi ch
are attributable to any such claim, but such defense and payments are
conditioned on the following:
a. that MOTOROLA will be notified promptly in writing by such
purchaser of any notice of such claim;
b. that MOTOROLA will have sole control of the defense of
such suit and all negotiations for its settlement or compromise;
and
c. Should the Product or parts become, or in MOTOROLA’S
opinion be likely to become, the subject of a claim of
infringement of a patent, that such purchaser will permit
MOTOROLA, at its option and expense, either to procure for
such purchaser the right to continue to using the Pr od uct or
87
Page 96
parts or to replace or modify the same so that it becomes noninfringing or to grant such purchaser a credit for the Product or
parts as depreciated and accept its return. The depreciation
will be an equal amount per year over the lifetime of the
Product or parts as established by MOTOROLA.
MOTOROLA will have no liability with respect to any claim of patent
infringement which is based upon the combination of the Product or parts
furnished here under with software, apparatus or devices not furnished by
MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary
equipment or software not furnished by MOTOROLA which is attached to or
used in connection with the Product or any parts thereof. In no event shall
MOTOROLA be liable for any incidental, special or consequential damages
arising from any claim of patent infring eme n t or allege d infringe men t.
Laws in the Uni ted S tates and ot her coun trie s pres erv e for MOTO ROL A cert ain
exclusive rights for copyrighted MOTOROLA software, such as the exclusive
rights to reproduce in copies and di stribute copies of such MOTOROLA
software. MOTOROLA software may be used in only the Product in which the
software was originally embodied and such software in such Product may not be
replaced, copi ed, distributed, mod ified in any way, or used to product any
derivative thereof. No other use including, without limitation, alteration,
modification, r eproduction, distribution, or reverse engineering of such
MOTOROLA software or exercise or rights in such MOTOROLA software is
permitted. No license is granted by implication, estoppel or otherwise under
MOTOROLA patent rights or copyrights.
88
www.mot.com/iDEN
Page 97
Patent & Trademark Information
Patent & Trademark Information
This product is protected under one or mor e of the following patents:
4291475, 4365221, 4369516, 4374370, 4378603, 4390963, 43982 65, 4400584,
4400585, 4434461, 4455534, 4486624, 4491972, 4523155, 45463 29, 4574243,
4581602, 4581749, 4585957, 4593155, 4594657, 4602218, 46059 87, 4616314,
4617520, 4628529, 4629829, 4633141, 4636593, 4636741, 46481 25, 4649543,
4654655, 4680787, 4704588, 4711361, 4715063, 4717884, 47301 95, 4731813,
4736277, 4737976, 4741018, 4742562, 4761621, 4764737, 47759 98, 4791527,
4794489, 4797929, 4797947, 4798975, 4802236, 4803726, 48093 56, 4811377,
4811404, 4817157, 4827507, 4829543, 4831647, 4843621, 48457 72, 4851966,
4852090, 4860336, 4860341, 4868576, 4870686, 4872196, 48736 83, 4876552,
4876656, 4876740, 4879533, 4885553, 4887050, 4890199, 48961 24, 4896361,
4897873, 4903326, 4903327, 4904549, 4904992, 4905288, 49053 01, 4912602,
4916262, 4918431, 4918732, 4922178, 4941203, 4942570, 49455 70, 4956854,
4959851, 4963812, 4964121, 4970475, 4972355, 4972432, 49724 55, 4975808,
4977589, 4977616, 4979207, 4984219, 4984290, 4989230, 49927 53, 4996529,
5008925, 5010309, 5010570, 5014294, 5014346, 5017856, 50181 88, 5020076,
5020091, 5020092, 5020093, 5023580, 5023866, 5023911, 50253 87, 5027388,
5028083, 5028859, 5029233, 5036532, 5038253, 5040127, 50420 71, 5045824,
5053924, 5055800, 5055802, 5055803, 5057762, 5058136, 50598 85, 5060264,
5063340, 5065408, 5067139, 5070310, 5077757, 5077790, 50816 74, 5083304,
5087004, 5093632, 5095503, 5107487, 5109400, 5111162, 51134 00, 5113436,
5117073, 5117441, 5117449, 5117450, 5121047, 5121288, 51214 12, 5122480,
5122722, 5124889, 5127040, 5127042, 5127100, 5128834, 51330 10, 5134717,
5140286, 5140635, 5142551, 5142696, 5144533, 5146620, 51484 71, 5148473,
5150075, 5150359, 5150384, 5151643, 5152006, 5152007, 51535 90, 5157693,
5160898, 5162144, 5163159, 5164652, 5166596, 5166642, 51685 22, 5170173,
5170485, 5170492, 5175729, 5175759, 5175874, 5182749, 51855 66, 5185790,
5187640, 5187809, 5192924, 5193223, 5195106, 5195108, 51988 87, 5200655,
5201069, 5203009, 5203012, 5203013, 5203021, 5204977, 52057 51, 5210793,
5211581, 5212815, 5212826, 5214675, 5214774, 5216389, 52202 90, 5220936,
5222078, 5222104, 5222251, 5230007, 5230093, 5233506, 52336 33, 5235492,
5237257, 5237570, 5239127, 5241545, 5241548, 5241592, 52416 88, 5242767,
5243355, 5247544, 5247565, 5249302, 5251331, 5255292, 52574 14, 5259005,
5260170, 5260988, 5261119, 5262710, 5263052, 5263055, 52652 71, 5267230,
5276588, 5276707, 5276913, 5276915, 5278832, 5278994, 52806 30, 5280637,
5280644, 5285443, 5287013, 5287553, 5287555, 5287556, 52895 05, 5297142,
5299232, 5301365, 5308716, 5321705, 5321737, 5321847, 53234 21, 5325405,
5325429, 5327578, 5327642, 5331123, 5333153, 5336984, 53389 09, 5343213,
5349588, 5351245, 5359696, 5361400, 5363071, 5365549, 53668 26, 5367538,
5367558, 5371791, 5373101, 5375143, 5375258, 5379324, 53811 14, 5384825,
5392000, 5392023, 5392331, 5396654, 5401927, 5402447, 54024 48, 5404580,
5404582, 5406146, 5406562, 5408693, 5410275, 5410741, 54147 11, 5420759,
89
Page 98
5424689, 5428362, 5428820, 5428836, 5430416, 5432017, 543 4947, 5436802,
5438684, 5442680, 5444764, 5446763, 5446766, 5448763, 544 8770, 5448771,
5453997, 5457744, 5459640, 5459774, 5461643, 5463351, 546 3406, 5463628,
5463646, 5463674, 5463688, 5463694, 5465409, 5465412, 546 9177, 5471671,
5475752, 5477192, 5485506, 5485513, 5486843, 5487184, 548 8649, 5490177,
5491739, 5493198, 5493700, 5493714, 5495206, 5495208, 549 7126, 5497382,
5497383, 5499273, 5499394, 5499397, 5502437, 5504494, 550 4812, 5506490,
5508709, 5509048, 5510693, 5511235, 5513078, 5513996, 551 9303, 5519346,
5519506, 5519777, 5524276, 5526398, 5528666, 5530399, 553 0922, 5533119,
5535258, 5535434, 5539360, 5542016, 5542103, 5542106, 554 2116, 5544250,
5546275, 5546380, 5551078, 5551627, 5553137, 5553376, 555 4996, 5555550,
5557743, 5559471, 5559522, 5559806, 5561436, 5561437, 556 1852, 5565881,
5566224, 5568548, 5570453, 5572223, 5572224, 5574976, 557 7267, 5577268,
5583520, 5584054, 5586146, 5588041, 5589796, 5590177, 559 4778, 5594951,
5598129, 5598431, 5600341, 5604050, 5604468, 5604787, 560 6332, 5606560,
5606730, 5613229, 5613863, 5615233, 5615259, 5615260, 562 1763, 5621766,
5625316, 5625683, 5628001, 5628057, 5628089, 5629979, 563 0159, 5630210,
5630213, 5630215, 5631538, 5633484, 5633786, 5634202, 564 0690, 5642368,
5646576, 5649306, 5649309, 5656914, 5656917, 5657418, 565 9601, 5660945,
5661433, 5664973, 5666429, 5668871, 5670912, 5673001, 567 3003, 5673287,
5674326, 5675591, 5675702, 5678201, 5678221, 5678227, 568 0063, 5684384,
5691947, 5692046, 5692101, 5696497, 5696821, 5699070, 569 9389, 5699408,
5701130, 5701244, 5701589, 5703470, 5703539, 5703909, 570 6019, 5706313,
5708445, 5710862, 5710987, 5711001, 5715520, 5715524, 571 7307, 5722052,
5724004, 5726983, 5729221, 5732350, 5737327, 5737685, 573 8954, 5739792,
5740525, 5742894, 5745116, 5745566, 5745848, 5747970, 574 8727, 5754141,
5754455, 5754583, 5754645, 5754956, 5758271, 5760714, 576 1300, 5761610,
5764100, 5764111, 5764730, 5764743, 5766794, 5771182, 577 1471, 5777521,
5777856, 5784368, 5784419, 5784585, 5787128, 5787577, 579 3315, 5793866,
5796822, 5797101, 5798716, 5799011, 5799256, 5801513, 580 1567, 5802111,
5805992, 5807012, 5808585, 5808586, 5809020, 5809419, 580 9421, 5809430,
5809433, 5809544, 5812093, 5812542, 5812590, 5814798, 581 5507, 5815570,
5815804, 5815805, 5815807, 5815820, 5821820, 5822726, 582 6224, 5831826,
5832080, 5832388, 5835006, 5835535, 5835785, 5838202, 584 1851, 5842122,
5844943, 5846094, 5848072, 5848152, 5848356, 5848718, 585 0440, 5854549,
5854785, 5854972, 5856763, 5856766, 5857148, 5857192, 585 9522, 5859567,
5859890, 5861853, 5862460, 5862493, 5864799, 5865487, 586 7063, 5867127,
5867140, 5867510, 5870670, 5872744, 5877633, 5878075, 587 8209, 5878336,
5878353, 5880637, 5880646, 5881377, 5889737, 5889768, 588 9859, 5892410,
5893036, 5894597, 5896054, 5896261, 5898933, 5900829, 590 1347, 5901357,
5903825, 5903852, 5905956, 5907418, 5907615, 5909102, 591 0944, 5912648,
5920549, 5920550, 5923007, 5924044, 5925835, 5925942, 592 6119, 5926503,
5926751, 5930268, 5930288, 5930299, 5933330, 5936516, 593 6972, 5939939,
5940452, 5940746, 5943027, 5945852, 5945964, 5946395, 594 9020, 5950131,
5950139, 5953413, 5954817, 5955700, 5955999, 5956626, 596 3848, 5963876,
5964858, 5966101, 5966667, 5966671, 5969545, 5974042, 597 7916, 5980268,
90
www.mot.com/iDEN
Page 99
Patent & Trademark Information
5982881, 5983082, 5987012, 5988577, 5995050, 5996178, 59991 15, 5999821,
5999832, 6002922, 6002937, 6005498, 6006104, 6008636, 60091 68, 6009309,
6009325, 6009336, 6009552, 6011699, 6011784, 6011959, 60119 61, 6012634,
6014376, 6014552, 6016312, 6016422, 6018584, 6018651, 60186 71, 6020787,
6021332, 6023191, 6023615, 6025753, 6035182, 6035191, 60355 22, 6038457,
6040683, 6040720, 6041241, 6043721, 6043786, 6044153, 60470 66, 6047084,
6049192, 6049233, 6049532, 6049704, 6049725, D284759, D285439, D288432,
D288683, D289156, D 292578, D292920, D295627, D295973, D2 95975, D296187,
D297734, D297735, D 297736, D299136, D299137, D299232, D3 00742, D300827,
D301473, D301476, D 301883, D302015, D303656, D304189, D3 05427, D305717,
D306015, D306163, D 306293, D306299, D306441, D306583, D3 06594, D307271,
D309301, D309451, D 314173, D315330, D315346, D315543, D3 15559, D315565,
D315907, D316417, D 316859, D320780, D322783, D324024, D3 24388, D325028,
D325029, D325032, D 325583, D325915, D327061, D327062, D3 28302, D332261,
D332785, D334746, D 337332, D338012, D338887, D339127, D3 39335, D339336,
D339337, D339564, D 339578, D339581, D339582, D340709, D3 40710, D340711,
D340906, D341589, D 342248, D342663, D342729, D342730, D3 42741, D343173,
D343615, D343616, D 343834, D343835, D343836, D344087, D3 44271, D344444,
D344511, D344512, D 344945, D345977, D346785, D346786, D3 46798, D348071,
D348250, D348427, D 348470, D348665, D348666, D348668, D3 48674, D348880,
D349273, D349701, D 350113, D350348, D350349, D350350, D3 51375, D351840,
D352497, D352503, D 352946, D353131, D353361, D353587, D3 53588, D353591,
D354055, D354062, D 355181, D355895, D356084, D356309, D3 57224, D357249,
D357457, D357680, D 357681, D358148, D359052, D359734, D3 59735, D359959,
D360398, D360632, D 361070, D361763, D362840, D362852, D3 65094, D365817,
D366872, D367640, D 368479, D368696, D369162, D369359, D3 69797, D370016,
D370463, D370672, D 372237, D372481, D372703, D372896, D3 72919, D373585,
D373764, D374013, D 374014, D374227, D374424, D374872, D3 75732, D375733,
D375734, D375932, D 375935, D375952, D376127, D377792, D3 77934, D378366,
D378911, D379558, D 379624, D379981, D379982, D380468, D3 80751, D381021,
D381664, D382537, D 382538, D382872, D383115, D383748, D3 83749, D383759,
D384080, D384662, D 384951, D384952, D385271, D385283, D3 85555, D385873,
D385874, D385875, D 385877, D385888, D386175, D386494, D3 86757, D387054,
D387055, D387199, D 387346, D388078, D388079, D388080, D3 88081, D388082,
D388424, D388429, D 388430, D388775, D388783, D388793, D3 89157, D389476,
D389478, D389488, D 389641, D390221, D390222, D390509, D3 91567, D391955,
D391966, D393470, D 394256, D394423, D394425, D394433, D3 94438, D394439,
D395301, D395302, D 395431, D395642, D395875, D396472, D3 97337, D397689,
D397694, D398926, D 400161, D400165, D400204, D400209, D4 00496, D400526,
D400527, D400874, D 401554, D401929, D403265, D404397, D4 05080, D405782,
D405801, D406098, D 406191, D406586, D406695, D406812, D4 07063, D407685,
D407708, D408401, D 408402, D408418, D408783, D408815, D4 09186, D410459,
D410460, D410929, D 411165, D411196, D411202, D411204, D4 11507, D411535,
D411843, D411844, D 412000, D412487, D412709, D413893, D4 13898, D414159,
D415122, D415499, D 416226, D417224, D417449, D419155, D4 19290, D419565,
D419956, D420008, D 420977, D421005, D421443, D421982, D4 22275, D422595
91
Page 100
Additional patents are pending.
MOTOROLA, the Stylized M Logo and all other trademarks indicated as such
herein are trademarks of Motorola, Inc. ®Reg. U.S. Pat. & Tm. Of f. ©
Copyright 2000 Motorola, Inc. All rights reserved. Manufactured under on e or
more of the U.S. patents listed in the User’s Guide.
T9 is a trademark ow ned by Tegic Commun ications, Inc.
All other product or service names mentioned in this manual are the property of
their respective trademark owners.
92
www.mot.com/iDEN
Loading...