Motorola MBP10 User Manual
MOTOROLA
MOTOROLA
USER’S GUIDE
MBP10
DIGITAL BABY MONITOR
The features described in this user’s guide are subject to
modifications without prior notice.
Welcome...
to your new Motorola Digital Baby Monitor!
Thank you for purchasing the MBP10. This baby monitor uses digitai
communication which ensures that you can hear your baby clearly
without any distracting noise or interference.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola product, you will need to provide a
copy of your dated sales receipt to confirm warranty status.
Registration is not required for warranty coverage.
For product related questions, please call:
This User’s Guide provides you with all the information you need to
get the most from your product.
Before you can use the baby monitor, you’ll need to insert and fully
charge the batteries on the Parent unit. Please read the Safety
Instructions in section 1 “Safety Instructions” before you install the
units.
Got everything?
1 X Parent unit
1 X Baby unit
2 X AAA Rechargeable batteries for the Parent unit
1 X Power adapter for the Parent unit
1 X Power adapter for the Baby unit
0845 218 0890 in the UK
(65) 68412668 in Singapore
On the Web:
www.motoroia.com
Overview of your Parent unit
1.
Link indicator LED
2.
Volume down
button
3.
Power On/Off
button @
4.
Speaker
Volume up
5.
button "¿0
Power (ON / ga'
6.
LED
7.
Volume indicator
LEDs
Power adapter
connector
Overview of your Baby unit
12. Power LED
13. Power On/Off
button
14. Microphone
15. Paging button
16. Power adapter
connector
Table of contents
Safety Instructions
Getting started
2.1 Baby unit power supply
2.2 Parent unit battery installation........................................................7
2.3 Parent unit power supply................................................................9
2.4 Link..................................................................................................9
2.5 Registration...................................................................................10
2.6 Paging...........................................................................................10
3.
Using the WIBP10
3.1 Volume adjustment on the Parent unit
Disposal of the device (environment)
Cleaning................................................................................11
Help.......................................................................................12
General Information
..................................................................
........................................................................
..................................................................
................................................................
..........................................
....................................
..............................................................
10
12
10
6
7
11
i. Safety Instructions
WARNING
This baby monitor is compliant with all relevant standards regarding
electromagnetic fields and is, when handled as described in the User’s
7
Guide, safe to use. Therefore, always read the instructions in this User’s
Guide carefully before using the device.
• Adult assembly is required. Keep small parts away from children
when assembling.
• This product is not a toy. Do not allow children to play with it.
• This baby monitor is not a substitute for responsible adult
supervision.
• Keep this User’s Guide for future reference.
• Do not place the baby unit or cables in the cot or within arm's reach of
the baby (the unit should be at least 1 metre away).
• Keep the cords out of reach of children.
• Do not cover the baby monitor with a towel or blanket.
• Never use extension cords with power adapters. Only use the power
adapters provided.
• Test the baby monitor before use. Become familiar with its functions.
• Do not use the baby monitor near water.
• Do not install the baby monitor near a heat source.
• Only use the chargers and power adapters provided. Do not use
other chargers or power adapters as this may damage the device and
batteries.
• Only insert batteries of the same type. Never use ordinary, nonrechargeable batteries in the parent unit. Insert batteries with the
right polarity (indicated in the battery compartment).
• Do not touch the charger or plug contacts with sharp or metal objects.
2. Getting started
2.1 Baby unit power supply
1. Connect the small plug of the power adapter to the power connector
on the baby unit and the other end of the adapter to the mains
socket (230V/50HZ).
NOTE
Only use the enclosed power adapter (6V DC/300mA).
2. Press The Power LED will illuminate.
3. Press and hold to switch off the baby unit.
2.2 Parent unit battery instaiiation
CAUTION
Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.
The Parent unit can be used with either rechargeable batteries (2 AAA
size, Ni-MH type supplied) or from the mains power via the power
adapter supplied.
WARNING
Never use ordinary, non-rechargeable batteries. The power mains
adapter provides a charging function, and non-rechargeable batteries
may burst and cause damage!
NOTE
The Ni-MH rechargeable batteries must be charged for 15 hours before
using the Parent unit without the mains power.
We recommend the rechargeable batteries are installed, so that the unit
continues to work in the event of a mains power failure.
1. Using a screwdriver, turn the screw of the battery cover on the back
of the parent unit 90 degrees in a counterclockwise direction.
Remove the battery cover.
NOTE
Rotate the belt clip to its hanging position to make it easier to access the
battery compartment.
Do not try to turn the screw further than the OPEN position marked on the cover.
2. Install 2 AAA size Ni-MH rechargeable batteries with the polarity as
shown in the diagram above, and by the "+” and markings in the
battery compartment.
3. Close the battery compartment and turn the screw 90 degrees back
in a clockwise direction.
4. Press @. The Power (ON / LED will illuminate green if it
only has battery power.
5. Press and hold @ to switch off the parent unit.
NOTE
When the battery level is low, the green power LED will flash and the
parent unit will emit a warning beep once every minute. If the baby unit
loses power or goes out of range, the link will be lost and the parent unit
will emit a warning beep every 3 seconds and the green link LED on the
parent unit will continue to flash.
WARNING
Do not mix old batteries with new ones.
Keep batteries away from small children.
Do not short-circuit batteries or dispose of in fire.
Remove the batteries if this device is not going to be used for a long
period of time.
2.3 Parent unit power supply
1. Connect the small plug of the poweradapter to the power connector
on the parent unit and the other end of the adapter to the mains
socket (230V/50HZ).
Only use the enclosed adapter (6V DC / 300mA).
2. Press The Power (ON / ^3) LED will illuminate red if it only
has mains power. It will illuminate orange if it has both the battery
and mains power.
3. Press and hold @ to switch off the parent unit.
2.4 Link
NOTE
Do not place the baby unit or cables in the cot or within arm's reach of
the baby (the unit should be at least 1 metre away).
When using the baby monitor for the first time, it is advised to test the
connection.
• Install the parent unit in the same room as the baby unit, but make
sure there is at least 1 metre between the 2 units.
• When both units are switched on, the parent unit will search for the
baby unit.
• The green link LED on the parent unit will flash until the parent unit is
connected with the baby unit.
Once the link is established, the LED will stop flashing.
• The sound captured by the microphone on the baby unit will be
audible on the parent unit.
The detected sound level is indicated by the LEDs on the front of the
parent unit.
• When the connection is established, move the parent unit to the room
you want to monitor from, but within the operational range.
• When there is no connection or out of range, the parent unit emits a
warning beep every 3 seconds and the green link LED on the parent
unit will flash.
• Move the parent unit closer until the link is re-established.
2.5 Registration
The baby monitor is already pre-registered upon your purchase. You do
not need to re-register it again unless the baby unit loses its link with the
parent unit.
To re-register your baby monitor, follow the procedure below:
1. Switch off the mains power by removing the power supply for both
the baby and parent units, and remove a battery from the parent unit.
2. Press and hold for 3 seconds while the baby unit mains
power is switched back on. The baby unit is in registration mode.
3. Press and hold @ while the parent unit mains power is switched
back on, and keep holding it down until the red sound LEDs flash.
The parent unit is in registration mode.
4. Wait for the 2 units to search and establish the link.
When the registration is complete, the LEDs stop flashing and the parent
unit emits a long beep.
2.6 Paging
If the parent unit is misplaced, press and hold on the baby unit for
2 seconds.
The parent unit will emit a repeated beep tone for 30 seconds so that you
can locate it.
Press any key on the parent unit, or the again on the Baby unit, to
stop paging.
3. Using the MBP10
3.1 Volume adjustment on the Parent unit
There are 5 volume levels on the parent unit.
• Press A to increase the volume level.
Press T to decrease the volume level.
NOTE
When you press A or J a beep is played at the volume level currently
set, but if you try to adjust beyond the maximum or minimum levels it will
output a double beep.
4. Disposal of the device (environment)
At the end of the product lifecycle, you should not dispose of
this product with normal household waste, but take the product
to a collection point for the recycling of electrical and electronic
equipment. The symbol on the product, User's Guide and/or
box indicates this.
Some of the product materials can be re-used if you take them to a
recycling point. By reusing some parts or raw materials from used
products you make an important contribution to the protection of the
environment.
Please contact your local authorities in case you need more information
on the collection points in your area.
Dispose of the batteries in an environmentally-friendly manner according
to your local regulations.
5. Cleaning
Clean the MBP10 with a slightly damp cloth or with an anti-static cloth.
Never use cleaning agents or abrasive solvents.
Cleaning and care
• Do not clean any part of the product with thinners or other solvents
and chemicals — this may cause permanent damage to the product
which is not covered by the warranty. When necessary, clean it with a
damp cloth.
• Keep your MBP10 away from hot, humid areas or strong sunlight,
and do not let it get wet.
• Every effort has been made to ensure high standards of reliability for
yourMBPIO. However, if something does go wrong, please do not try
to repair it yourself — contact Customer Service for assistance.
6. Help
Registration
If the baby unit has lost its link with the parent unit
• Try recharging or replacing the batteries.
• If the baby unit is too far away it may be going out of range, so move
the baby unit closer to the parent unit.
• Reset the units by unplugging the units’ electrical power. Wait for
around 15 seconds and plug it back in again. Allow up to one minute
for the baby unit and the parent unit to synchronise.
• See “2.5 Registration" if there is a need to re-register the units.
Interference
Noise interference on your parent unit
• Your baby and parent units may be too close. Move them further
away from each other.
• Make sure there is at least 1 metre between the 2 units to avoid
feedback howling.
• If the baby unit is too far away it may be going out of range, so move
the baby unit closer to the parent unit.
• Make sure the baby and parent units are not near other electrical
equipment, such as a television, computer or cordless/mobile
telephone.
7. General Information
If your product is not working properiy....
1. Read this User’s Guide or the Quick Start Guide.
2. Visit our website: http://www.motorola.com
3. Contact Customer Service at:
0845 218 0890 in the UK
(65) 68412668 in Singapore
To order replacement batteries, contact customer service or visit our
website.
Consumer Products and Accessories purchased in the
United Kingdom and Singapore
What Does this Warranty Cover?
Subject to the exclusions and limitations contained below, Binatone Electronics
International LTD. warrants the Motorola branded consumer products that it
manufactures (“Products”) and the Motorola branded or certified accessories sold for
use with these Products that it manufactures (“Accessories") to be free from defects
in materials and workmanship under normal consumer usage for the period(s)
outlined below. This limited warranty is a consumer’s exclusive remedy, and only
applies as follows to new Motorola branded Products and Accessories manufactured
by Binatone Electronics International LTD., and purchased by consumers in the
United Kingdom and Singapore, which are accompanied by this written warranty:
Who is covered?
This warranty covers only the first consumer purchaser, and is not transferable.
What will BINATONE ELECTRONICS INTERNATIONAL LTD. do?
BINATONE ELECTRONICS INTERNATIONAL LTD., at its sole option, will at no
charge repair, replace or refund the purchase price of any Products or Accessories
that does not conform to this warranty. Binatone Electronics International LTD. may
use functionally equivalent reconditioned/ refurbished/ pre-owned or new Products,
Accessories or parts in such repair or replacement and any Products, Accessories
or parts removed or being replaced under this warranty become the property of
Binatone Electronics International LTD.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES OR CONDITIONS IRRESPECTIVE OF WHETHER
THEY ARE IMPOSED BY LAW OR OTHERWISE, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND
IS PROVIDED IN LIEU OF ALL WARRANTIES AND MOTOROLA AND
BINATONE ELECTRONICS INTERNATIONAL LTD. MAKES NO OTHER
WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED. IN NO EVENT
SHALL MOTOROLA OR BINATONE ELECTRONICS INTERNATIONAL LTD. BE
LIABLE, WHETHER UNDER THIS LIMITED WARRANTY OR IN CONTRACT OR
TORT (INCLUDING NEGLIGENCE OR STRICT PRODUCT LIABILITY) OR
OTHERWISE FOR DAMAGES OR CLAIMS IN EXCESS OF THE PURCHASE
PRICE OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR
LOSS OF REVENUE, SAVINGS OR PROFITS, LOSS OF BUSINESS, LOSS OF
PROGRAMS DATA INFORMATION (WHETHER CONFIDENTIAL
PROPRIETARY OR PERSONAL IN NATURE OR OTHERWISE) OR OTHER
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY
OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES AND BINATONE
ELECTRONICS INTERNATIONAL LTD. SHALL UNDER NO CIRCUMSTANCES
BE LIABLE FOR ANY CLAIMS OR DEMANDS MADE BY ANY THIRD PARTY OR
MADE BY YOU ON BEHALF OF ANY THIRD PARTY TO THE FULL EXTENT
THESE DAMAGES OR CLAIMS MAY BE DISCLAIMED BY LAW.
Some states, countries or jurisdictions do not ailow the limitation or exciusion of
incidentai or consequentiai damages, or limitation on the length of an implied
warranty, so the above iimitations or exclusions may not appiy to you in such
states, countries or jurisdictions. This warranty gives you specific legai rights, and
you may also have other rights that vary from state to state or from one country/
jurisdiction to another.
Products or Accessories Covered Length of Coverage
Consumer Products
Consumer Accessories Ninety (90) days from the date of
Consumer Products and
Accessories that are Repaired or
Replaced
One (1) year from the date of purchase by
the first consumer purchaser of the
product.
purchase by fhe first consumer purchaser
of the accessory.
The baiance of the originai warranty or
for ninety (90) days from the date
returned to the consumer, whichever is
longer.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and replacement of parts
due to normal wear and tear are excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls below 80% of their rated
capacity and batteries that leak are covered by this limited warranty. Battery life and
the changes in battery capacity with time or use are excluded from this warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper or
unreasonable use, operation, storage, misuse or abuse, accident or neglect or
other external cause, such as physical damage (cracks, scratches, etc.) to the
surface of the product resulting from misuse; (b) your failure to follow or operate
outside the usage parameters stated in the user instructions that came with the
Products or Accessories; (c) contact with liquid, water, rain, extreme humidity or
heavy perspiration, sand, dirt or the like, extreme heat, or food; (d) use of the
Products or Accessories for commercial purposes or subjecting the Product or
Accessory to abnormal usage or conditions; or (e) other acts or omissions which
are not the fault or neglect of Motorola or Binatone Electronics International LTD.,
are excluded from coverage.
Use of Non-Motorola branded Products and Accessories. Defects or damage
that result from the use of Non-Motorola branded or certified Products or
Accessories or other peripheral equipment are excluded from coverage.
Unauthorised Service or Modification. Defects or damages resulting from
service, testing, adjustment, installation, maintenance, alteration, or modification in
any way by someone other than Motorola, Binatone Electronics International LTD.
or its authorised service centres, are excluded from coverage.
Altered Products. Products or Accessories with (a) serial numbers or date tags
that have been removed, altered or obliterated; (b) broken seals or that show
evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming
or non-Motorola branded housings, or parts, are excluded from coverage.
Communication Services. Defects, damages, or the failure of Products or
Accessories due to any communication service or signal you may subscribe to or
use with the Products or Accessories is excluded from coverage.
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
0845 218 0890 in the UK
(65) 68412668 in Singapore
You will receive instructions on howto ship the Products or Accessories, the shipment
of which shall be at your own risk and expense, to a BINATONE ELECTRONICS
INTERNATIONAL LTD. Authorised Repair Centre. To obtain service, you must
include: (a) a copy of your receipt, bill of sale or other comparable proof of purchase
of the Products or Accessories showing the date of purchase; (b) a written description
of the problem; and, most importantly; (c) your address and telephone number.
These terms and conditions constitute the complete warranty agreement between
you and BINATONE ELECTRONICS INTERNATIONAL LTD. regarding the
Products or Accessories purchased by you, and supersede any prior agreement or
representations, including representations made in any literature publications or
promotional materials issued by BINATONE ELECTRONICS INTERNATIONAL
LTD. or representations made by any agent employee or staff of BINATONE
ELECTRONICS INTERNATIONAL LTD., that may have been made in connection
with the said purchase.
Technical Specifications
Frequency range 1.88 to 1.9 GHz
Channel bandwidthl.728 MHz
Operating range Extended range up to 950 feet*
Electrical power Parent and Baby units:
(bandwidth = 20 MHz)
*Based on unobstructed line of sight. Actual range will vary
depending on surroundings.
Input - 100-240VAC, 50/60HZ (UK/EU plug);
Output — 6VDC, 300 mA (Supplier: Kings,
Model: KSS05-060-0300B/KSS05-060-0300G)
Parent unit:
IxAAA 600mAh Ni-MH rechargeable batteries
(Supplier: BYD, Model: H-AAA600A;
Supplier: GPI, Model: GN60A/\AHC)
BINATONE TELECOM PLC
1 Apsley Wiy London NW2 7HF,United Kingdom.
Tel: ^4(0} 20 8955 2700 Fax: ->44(0] 20 8344 8877
e-mal: blnalonaukAtoalonelelecom.co.uk
F.C Declai-atinn of Conformity
We the manufacturer/Importer : Binatone Telecom Pic
Declare under our sole responsibility that the following product
Type of equipment:
Model Name:
Country of Origin:
Brand:
complies with the essential protection requirements of R&l'TB Directive 1999/5/EC on the
approximation of the laws of the Member States relating to Radio Spectrum Matters, the
Council Directive 2004/I08/EC on the approximation of the laws of the Member States
relating to electromagnetic compatibility (EMC) and the European Community Directive
2006/95/EC relating to Electrical Safety.
Assessment of compliance of the product with the requirements relating to the essential
requirements according to Article 3 R&TTE was based on Annex III of the Directive
1999/5/EC and the following standard;
Radio Spectrum;
EMC;
The product is labelled with the European Approval Marking CE as show. Any Unauthorized
modification of the product voids this Declaration.
Manufacturer / Importer
(Signature of authorized person)
Signature: (Paul Tsui, Product Operation Director) Place & Date:
MOTOROLA
Q
Manufactured, distributed or sold by Binatone Electronics International LTD., official licensee
for this product. MOTOROLA and the Stylized M Logo, and other Motorola trademarks and
trade dress are owned by Motorola, Inc. and are used under license from Motorola, Inc.
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office.
All other product or service names are the property of their respective owners.
3 Motorola, Inc. 2010. All rights reserved.
EN 301406; V1.5.1:2003;
EN 301489-1;V1.8.1:2008;
EN30I489-6;V1.3.1;2008;
EN 60950-I;2006
Binatone
1 Apsley Way London
NW2 7HF, United Kingdom.
Diaital Baby Monitor
MBPIO
China
Motorola
London, 15 Jun 2009
Printed in China
Version 1.0
Loading...