Parts List
HT600 Series
110
8/03
Replacement parts may no longer be available
https://www.motorola.com/businessonline
111
8/03
Parts List
HT600 Series
REF
.
NO. PART NO. DESCRIPTION
REF
.
NO. PART NO. DESCRIPTION
1 0105956M63 Assembly, Frame; includes:
*Item 1 Frame
*Item 40
2 0105955N18 Assembly, Housing; includes:
*Item 2 Housing
*Items 56, 58, 59, and 60
3 1505527P01 Cover, Front
5 3305543P01 Nameplate, Front
6 0105951N41 Assembly, Top Control Panel;
includes:
*Item 6 Panel
*Items 17, 28, 29, and 32
7 ---- Carrier, Flex Top
8 ---- Shield, Bottom
9 ---- Assembly, Controller Flex;
includes:
*Item 9 Controller Flex
*Items 10, 80, 84, 89, and
90 (The Controller Flex
Assembly also includes
electrical parts. See Note)
10 See Note *Shield, Center; part of item 9
11 0102706J99 Cover, Dust
12 0105951N79 Assembly, Knob; includes:
*Item 12 Knob
*Item 13
13 4205123Q02 Clip, Push; part of item 12
14 0105950N92 Assembly, Knob; includes:
*Item 14 Knob
*Item 15
15 See Note *Clip, Push; part of item 14
16 1305676R01 Escutcheon (2-Freq. Radios)
or
1305676R02 Escutcheon (6-Freq. Radios)
17 *Pin, Contact (P7); (not field
replaceable, order top
control panel assembly
0105951N41)
18 0405218Q01 Washer
19 0205163Q01 Nut, Spanner
20 0405162Q01 Washer, Flat
21 0205765L02 Nut, Spanner
22 0405216L04 Washer, Flat
23 0300136785 Screw, Phillips Hd., 4-40 x 3⁄16˝
24 0484345A06 Washer, Seal
25 0205629L02 Nut, Hex; 2 req’d
26 0405162Q02 Washer, Flat; 2 req’d
27 3205141Q02 Gasket, “O” Ring
28 See Note *Bushing, Antenna; part of
item 6
29 See Note *Lug, Antenna; part of item 6
30 4805729G24 LED, Bicolor (CR413A/CR413B)
31 3205131S01 Seal, LED
32 ---- Stud, Insert; part of item 6
33 3205082E01 Gasket, “O” Ring
84A See Note *Jack (J2), part of item 9
84B See Note *Jack (J1), part of item 9
85A See Note *Jack (P2), part of item 86
85B See Note *Jack (P1), part of item 88
86 ---- Assembly, Volume Pot Flex;
includes:
*Item 86 Volume Pot Flex
*Items 85A and 106
88 0105956M68 Assembly, Frequency Switch
Flex; includes:
*Item 88 Frequency Switch
Flex
*Item 85B
89A See Note *Jack (J3), part of item 9
89B See Note *Jack (J4), part of item 9
90 See Note *Jack (J5), part of item 9
91 3205141Q01 Gasket, “O” Ring
92 4205140Q01 Clamp, Speaker
93 1405135P01 Insulator, Microphone
94 See Note *Flex, Microphone;
part of item 98
95 5005155Q03 Speaker (LS1)
96 4205139Q01 Retainer, Microphone
97 See Note *Boot, Microphone;
part of item 98
98 0105956M62 Assembly, Microphone;
includes:
*Item 98 Microphone
*Items 78, 94, 97, 98,
and 103
99 ---- Pad, Microphone Boot
101 0300138620 Screw, Flat Phillips Hd.;
2-56 x 7⁄16˝
102 3505143Q04 Felt, Speaker
103 See Note *Plug (P5), part of item 98
105 ---- Not used
106 See Note *Sockets (J7), part of item 86
107 3905509R02 Contact, 3 req’d
108 0405534R01 Washer, Flat
109 5402446J01 Label, Instruction
110 ---- Shield, I-F
111 1405496R01 Insulator, I-F Shield
112 3905130N01 Contact Strip
113 2605573S01 Shield
114 1405299Q01 Insulator, Speaker
115 0300136771 Screw, Phillips; 2-56 x 3⁄16˝
117 7505501R02 Pad, Speaker
118 2605762R01 Shield, Controller Flex
120 0305103S01 Screw, Captive
121 7505501R03 Pad, Front Cover
122 2605123S01 Shield, Back
*111NOTE: Not field replaceable, order parent Assembly.
Cancelled Product HT600:
Aftermarket support criteria has
been met for spare parts. Items
may no longer be available.
REF
.
NO. PART NO. DESCRIPTION
34 0300132342 Screw, Phillips; 2-56 x 1⁄4˝
35 4005148Q05 Switch, Frequency (S2)
36 3205141Q03 Gasket, “O” Ring
37 1805100Q04 Switch/Pot, On-Off/Volume
(S1/R140)
38 4005101Q01 Switch, PL (S3)
39 0300140369 Screw, Flat Hd.; 2-56 x 1⁄8˝
40 See Note *Insert, Frame; part of item 1
41 4605945K05 Contact Stud, Battery
42 3905127Q01 Contact, B+
43 3205082E24 Gasket, “O” Ring
44 0705830C02 Support, Contact
45 3905421C13 Contact, Battery
46 2905124Q01 Lug
47 0400002625 Lockwasher, Split #2
48 4105944K01 Spring, Battery Latch
49 5505536P01 Latch
50 0300139444 Screw, Phillips Hd.; 2-56 x 5⁄32˝
51 3205082E03 Gasket, “O” Ring
52 6505214E05 Fuse (F1)
53 0400009761 Lockwasher, Split #4
54 0305941K01 Screw
55 6405531P02 Plate, Base
56 3805236Q01 *Actuator, PTT part of item 2
57 4505535P01 Lever, PTT
58 4205534P01 *Retainer, PTT part of item 2
59 6405186Q01 *Plate, Actuator Button;
part of item 2
60 3805187Q01 *Button, Actuator;
part of item 2
61 0305137Q04 Screw, Phillips; 4-40 x 1⁄2˝
64 See Note *Seal, Dome (PTT);
part of item 67
65 See Note *Seal, Dome, (Mon);
part of item 67
66 See Note *Contact, Snap Dome;
part of item 67
67 0105951N40 Assembly, B+ PTT Flex;
includes:
*Item 67 Flex
*Items 64, 65, and 66
68 ---- Housing, VCO
70 ---- Screw, Flat – not available
74 2605775R02 Shield, Main Back
75 0300136783 Screw, Phillips Hd.; 2-56 x 5⁄16˝
76 ---- Not used
77B ---- Not used
77C 2605578P02 Heatsink (Low Power Models)
78 See Note *Tubing, Heat Shrink;
part of item 98
79 0300138620 Screw, Phillips; 2-56 x 5⁄16˝
80 See Note *Header, part of item 9
81 1405753R01 Insulator, Front Shield
82 2605711R03 Shield Front
83 ---- Insulator, Flex
112
8/03
Portable
Accessories
HT600 Series
Chargers
Rapid/Regular Rate Desktop Chargers
A variety of chargers are available to fit the charging capabilities of
your batteries. Choose rapid or regular rate, single unit chargers. The
rapid chargers are equipped with red and green lights to indicate
rapid charging or charge complete. All desktop units will accept any
of the three battery sizes, with or without radio attached.
NTN4636A Desktop,
Regular Charge Rate,
220V, 50-60 Hz, (supplied
with 2 prong plug)
NTN4633C Desktop,
Rapid Charge Rate, 117V
NTN4634B Desktop, Rapid Charge Rate, 220V,
50-60 Hz, (supplied with 2 prong plug)
Compact Chargers
The compact charger provides a 16 hour charge rate. The charger’s
small size and weight make it ideal for users who occasionally
charge their radio at home.
NTN4666B Compact, Regular Charge Rate, 117V
NTN4667A Compact, Regular
Charge Rate, 220V, 50-60 Hz,
(supplied with 2 prong plug)
Chargers
Multi-Unit Chargers
NTN4668C Multi-Unit
Desktop, Rapid Rate, 117V
AC, 50-60 Hz
NLN7967A Wall Mount for
6 Unit Charger
Vehicular Chargers
*NTN5438A 12V DC, Vehicular Charger (16 hour charge rate)
PAC-RT compatible
NKN6428A 12V Cable Kit. (Only required if not used with a
PAC-RT/mobile system)
NTN5368A RF Adapter (Utilizes universal
connector, incompatible with audio
accessories)
NKN6408A RF Cable Kit
(Does not include antenna)
*Not compatible with Kits NKN6149A, NKN6150A and NKN6151A.
NTN4633C
NTN4666B
NTN4668C
NLN7967A
NTN5368A
NKN6408A
https://www.motorola.com/businessonline
113
8/03
Portable
Accessories
HT600 Series
Battery Maintenance System
plus
(BMS
plus
)
Using interchangeable battery adapters (sold separately), the BMS
plus
is capable of charging and discharging, analyzing, conditioning and
cycle test on batteries; tracking battery voltage and capacity (mAh).
The BMS
plus
offers a 3 year warranty. Its easy-to-use design supports
hundreds of 2-way, cellular, and camcorder batteries with printer
port* (Serial-RS-232C port – uses female 9-pin to male 25-pin cable).
WPLN4079BR Six-Station, 110V AC, 50/60 Hz
WPLN4080BR Six-Station, 230V AC, 50/60 Hz
BMS
plus
Adapter
TDN9441A Standard Adapter, HT600
*Compatible with the STAR Micronics SP200 series printers, available from any STAR
Micronics distributor, and other printers with STAR emulation.
Battery Optimizing System II (BOS II)
No other battery analyzer
matches the speed,
accuracy, and versatility of
the Battery Optimizing
System II. Ideal for large
fleet, public safety, and all
other users who rely on their
battery performance. Now
with increased power, more
sophisticated programming
options, and easier to use
navigation paths, optimizing
your batteries was never
easier. Key features include:
• Support for NiCd, NiMH, Li-ion, and SLA batteries
• 100 watt power supply and programmable from 100 mAH to
4 amps per station
• Interchangeable adapters accomodate all major brands
• Includes a variety of user programs and allows for
customizable programming
• Proprietary recondition cycle restores NiCd and NiMH batteries
• Increased processing power and testing resolution – including
a three minute Quicktest that measures the batteries State of
Health (SoH)
• Printer output for reports and labels
• Three year warranty
WPLN4124AR BOS II, Four-Station, 100-240V AC (US line cord)
WPLN4125AR BOS II, Four-Station, 100-240V AC (UK/Euro line cords)
BOS II Adapter
RL-71173 Standard Adapter, HT600
WPLN4079BR
WPLN4124AR
114
8/03
Portable
Accessories
HT600 Series
Motorola Conditioning Charger (MCC)
The MCC will help extend
battery life and enhance
battery operation. It will
safely condition and charge
your specified Nickel
Cadmium (NiCd) and Nickel
Metal Hydride (NiMH)
batteries in approximately
an hour.
WPPN4009BR 110V AC
Base Charge Unit with
Adapter Plate
3080384G15 Cigarette Lighter Adapter Cord
RLN4814A Mounting Bracket for Motorola
Conditioning Chargers
MCC Multi-Unit Conditioning Chargers
WPPN4074BR Four-station, 110V with permanent adapter plates
WPPN4075BR Four-station, 220V with permanent adapter plates
Carrying Accessories
Carrying Cases
A variety of carrying accessories are
available for your comfort and convenience.
The carrying cases are made of top quality
leather and are available in sizes designed
to fit your radio and battery. Cases are
available with standard belt loop or swivel
back covers, with a restraining T-strap.
Standard
NTN5460B Leather Carry Case with
T-Strap and Spacer, for High or Medium
Capacity Battery (Snap)
Swivel
NTN5461B Leather Carry Case with T-Strap, Spacer and
2-1⁄2˝ Belt Loop, for High or Medium Capacity Battery (Snap)
NTN5883A Leather Carry Case with T-strap, Spacer, and Belt Loop,
for High or Medium Capacity Battery (Snap), fits 3˝ Belt
NTN5450B Leather DTMF Swivel Carry Case, Long (Snap),
fits 2-1⁄4˝ Belt
NTN5884A Leather DTMF Carry Case, Long (Snap), fits 3˝ Belt
WPPN4009AR
NTN5460B
https://www.motorola.com/businessonline
115
8/03
Portable
Accessories
HT600 Series
Carrying Accessories
Belt Loops
4282421J06 Swivel Belt Loop, 2-1⁄2˝
4205857B01 Swivel Belt Loop, 2˝
Belt Clip
NTN4813B Belt Clip, 1-1⁄2˝
NTN5389B Belt Clip, 2-1⁄4˝
NTN5602A Public Safety Full 3˝ Clip,
Black Aluminum
Belt Clip Carry Holder
NTN4814C Belt Clip Carry Holder,
fits 2-1⁄4˝ Belt
NTN5827A Belt Clip Carry Holder,
fits 3˝ Belt
Portable Radio Hanger
The portable radio hanger slides over and hangs from the door panel
in a vehicle. The radio’s belt clip slides onto the portable hanger
allowing convenient, easy mounting. Two sizes are available to fit
door panels.
TDN9327A Portable Radio Hanger, for
Door Panels up to 2-3⁄4˝
TDN9373A Portable Radio Hanger, for
Door Panels 2-3⁄4˝ to 3-1⁄4˝
Carrying Accessories
Carrying Strap
NTN5243A Carrying Strap, Black
Belt
4200865599 1-3/4˝ Wide Leather
Belt, for all models
T-Straps
4205386S03 T-strap, Nylon for Leather
Carrying Cases (Snap)
4205386S01 T-Strap, Nylon for Leather
Carrying Cases (Velcro)
4205447R03 T-Strap, Urethane, for Carry
Holder (Snap)
Spacer
Enables light capacity battery to fit in a small case and medium
capacity battery to fit in a medium case. Spacer is included in every
carry case.
4305525R02 Spacer (spare)
Button Back Cover
NTN5497A T-Bar Button Back Cover Kit,
Black (order swivel belt loop separately)
NTN4813B
NTN4814C
TDN9327A
4282421J06
NTN5243A
4200865599
4205386S01
4205447R03
NTN5497A
116
8/03
Portable
Accessories
HT600 Series
Carrying Accessories
Universal Carry Accessories
HLN6602A Universal
Chest Pack with Radio
Holder, Pen Holder and
Velcro Secured Pocket
1505596Z02 Replacement
Strap for HLN6602
RLN4815A Universal
RadioPAK™ with Radio
Holder. Worn around waist
with adjustable belt.
Includes attached 6” by 8” zippered pouch for other job necessities
RLN4570A Break-A-Way Chest Pack; all of the same features as the
original chest pack (HLN6602A) plus break-a-way tabs that allow
that allow the entire pack to be pulled off with approximately 10 lbs
of pressure.
4280384F89 Universal RadioPAK™ belt lengthener; fits waists larger
than 40”
Audio Accessories
Remote Speaker
Microphone
This speaker microphone provides
remote talk and listen capability.
By attaching the microphone to the
universal connector, you can use
the remote speaker microphone to
transmit or receive while the radio
remains comfortably on the belt in
the case.
NMN6145B Remote Speaker Microphone with Clip, Coil Cord and
2.5 mm Earphone Jack
NMN6156B Remote Speaker/ Microphone with Clip and Coil Cord
NTN5493A UHF Public Safety Remote Speaker Microphone with
Clip Back and Straight Cord (Order required antenna separately)
Audio Accessories
NTN5050A UHF Public Safety Speaker Microphone with velcro back
and straight cord (order antenna and velcro patch separately)
Antennas for Public Safety Microphones
8505309N09 ...........400-440 MHz
8505309N10 ...........440-470 MHz
8505309N11 ...........470-512 MHz
NLN8410A Velcro pin attachment
Ear Piece
5083693B01 Earphone and volume control (requires NTN4812B)
5083693B04 Earpiece and Volume Control (2.5 mm)
5880378B84 2.5 to 3.5 Jack Adapter
5880380B35 3.5 to 2.5 Jack Adapter
NTN4812B Earphone Jack Adapter
Flexible Ear
Receiver
BDN6717B Ear receiver
with 3.5 mm plug rests on
the outside of the ear, to
be used with adapter
NTN4812
Surveillance
ZMN6031A Three wire
surveillance accessory with
microphone and push-to-talk
separate. Factory Mutual
Approved. Requires
NTN5075B
ZMN6032A Two wire
surveillance accessory with
microphone and push-to-talk
combined. Factory Mutual
Approved. Requires
NTN5075B
NTN5075B Hirose Adapter for Two- and Three-Wire
Surveillance Accessories.
HLN6602A
NMN6156B
NLN8410A
BDN6717B
ZMN6031A
https://www.motorola.com/businessonline
117
8/03
Portable
Accessories
HT600 Series
Audio Accessories
Epaulet Strap
Black leather epaulet straps secure
remote speaker microphones to epaulet
of shirts or jackets and attach around
cord. Allows reliable communications in
hostile environments with Velcro or clip
style strap.
RLN4294A Epaulet Strap, Velcro
RLN4295A Epaulet Strap, Small Clip
Ear Mics
Single unit microphone and speaker worn in the ear. Eliminates the
need for handheld microphones or conventional headsets. Compact,
rugged design allows use under hearing protectors and protective
clothing. Order cable separately.
RMN4001B Ear Mike, EM200
0180359A39 Interface Cable for
HT600
0180359A51 Optional PTT Ring Switch for
RMN4001A only
0180356B97 Optional PTT Ring Switch for
RMN4001B Only
Audio Accessories
Ear Microphone System
This compact unit picks up the voice through bone vibrations in the
ear canal. Ideal for use in high noise environments. Available in PTT
or Voice activated (VOX) capabilities for total hands free
communications. Order Interface Module separately.
*BDN6677A Ear Microphone for
Standard Noise Levels
(up to 95 dB), Black
*BDN6678A Ear Microphone for
Standard Noise Levels
(up to 95 dB), Beige
*BDN6641A Ear Microphone for High
Noise Levels (up to 105 dB), Grey
Interface Modules
*BDN6656B Push-To-Talk
Interface Module
*BDN6657B Voice-Activated
Interface Module
Optional Accessories
0180300E25 Earguard with
Adjustable Loop
*0180358B38 Remote Push-To-Talk
Ring Switch
0180358B32 Earholder, Black, Size Small; Secures microphone in ear
0180358B33 Earholder, Black, Size Medium;
Secures microphone in ear
0180358B34 Earholder, Black, Size Large;
Secures microphone in ear
0180358B35 Earholder, Clear, Size Small;
Secures microphone in ear
0180358B36 Earholder, Clear, Size Medium,
Secures microphone in ear
0180358B37 Earholder, Clear, Size Large; Secures microphone in ear
4280369E44 Replaceable Belt Clip with Screws
5080358B28 Eartips, Black, Size Medium (10 per pack)
5080358B29 Eartips, Black, Size Large (10 per pack)
5080358B30 Eartips, Beige, Size Medium (10 per pack)
5080358B31 Eartips, Beige, Size Large (10 per pack)
* Intrinsically safe
RLN4294A
RLN4295A
RMN4001B
0180359A51
BDN6657B
(shown with BDN6677A)
BDN6677A
0180358B38
0180358B33
118
8/03
Portable
Accessories
HT600 Series
Audio Accessories
Headsets
High noise level headset (up to 125 dB) with noise cancelling
microphone and push-to-talk switch located on ear cup. Vox module
contained within headset on voice activated units. Factory Mutual
Approved. NOTE: Can be worn with or without hard hat or
fire helmet.
BDN6639A Radio Adapter
Cable for BDN6635, BDN6636
and BDN6645
BDN6645A Push-To-Talk
Headset with Boom
Microphone, Requires
Adapter Cable.
BDN6635B Voice-Activated Headset with Boom Microphone,
Requires Adapter Cable, Includes 110V Charger
BDN6636B Voice-Activated
Headset with Throat
Microphone, Requires Adapter
Cable, Includes 110V Charger
RMN4015A Lightweight
Headset with Swivel Boom
Microphone, single speaker and
in-line PTT
0180357B05 Spare Vox Headset Charger
6881126E79 Instruction Manual for BDN6645A
6881126E78 Instruction Manual for BDN6635B and BDN6636B
Audio Accessories
Vehicular Adapter Accessories
The Basic MVA console kits may be ordered separately. These items
allow use of the portable radio in a mobile application. Order
antenna separately.
NSN6054A 12-watt External Speaker
HMN1035C Microphone, Heavy-Duty Palm
HMN1056D Microphone, Compact Palm
HMN3013A Microphone, DTMF
BDN6645A
BDN6636B
HMN1056D
NSN6054A
https://www.motorola.com/businessonline
119
8/03
Antennas,
Batteries
HT600 Series
Portable Batteries
Nickel-Cadmium Premium
Part Number: NTN4564B
Volts: 10
Avg. mAh: 550
Height: 2-7⁄16˝
Intrinsically Safe: Yes
Part Number: NTN4584BR
Volts: 10
Avg. mAh: 630
Height: 2-7⁄16˝
Intrinsically Safe: No
Part Number: NTN5414BR
Volts: 10
Avg. mAh: 1100
Height: 3-5⁄16˝
Intrinsically Safe: No
Part Number: NTN5415B
Volts: 10
Avg. mAh: 1000
Height: 3-5⁄16˝
Intrinsically Safe: Yes
Nickel Metal Hydride Premium
Part Number: NTN7016A
Volts: 10
Avg. mAh: 950
Height: 2-7⁄16˝
Intrinsically Safe: No
NTN7016A
NTN5414BR
NTN4564B
Portable Antennas
Heliflex Antenna
Motorola Heliflex antennas are specifically engineered for maximum
output and greatest communication coverage.
8505816K01
Heliflex Molded, 136-150.8 MHz, 6.5”
8505816K21
Heliflex Molded, 150.8-162 MHz, 6”
8505816K23
Heliflex Molded, 162-174 MHz, 6”
8505816K24
Heliflex Molded, 403-433 MHz, 3”
8505816K25
Heliflex Molded, 440-470 MHz, 3”
8505816K26
Heliflex Molded, 470-512 MHz, 3”
Flexible Whip
Flexible Whip antennas have a one-piece
finish and steel core for optimal radiation
characteristics. Provides more comfort when
radio is worn on the belt.
8505247K06
Flexible Whip, 403-512 MHz, 5.5”
8505816K23
8505247K06
8505816K26
120
8/03
Service Tools,
Aids
HT600 Series
Service Aids
Battery Adapter
Replaces radio housing during
servicing and provides easy
mounting for battery eliminator,
RTL4226B.
1580368B62 Battery Adapter
Cloning Cable
Enables the frequencies, squelch codes, squelch and deviation
settings to be duplicated from one radio to another. Only identical
models and sub-models are compatible for cloning.
NKN6376A
Cloning Cable
Antenna Adapters
NTN5368A Adapter for HT600
NKN6408A Cable Adapter for HT600
Radio Test and
Programming Cable
Used with Portable Radio Test
Set, RTX4005, for transmitter,
receiver alignment and
performance checks. Also used in
programming radio.
RTK4205C
Test and Programming Cable
NKN6376A
1580368B62
RTK4205C
Alignment Tool
6605106N01 Tuning Tool, Adjusts Tunable Coils, Preselector,
Reference Oscillator Frequency and Trimmer Capacitors
Service Tools
RSX4043A Torque Screwdriver,
Order Bits Separately
6680321B86 #0 Phillips Bit for
Radio Screws
6680321B79 #1 Phillips Power
Bit for Radio Screws
6680370B95 Spanner Tool Bit for
Toggle Switch Nut
6680371B34 Spanner Bit for
Antenna Bushing
6680371B03 Nut Driver Bit for
Volume Control and Frequency
Select Switch
Service Aids
Battery Eliminator
The Battery Eliminator acts like a battery
with a cable to access a DC external power
supply. It is ideal to inspect transmitters
and receivers on incoming radios. Reverse
supply polarity protection and input fuse
protection are provided.
RTL4226B Battery Eliminator
6605106N01
RSX4043A
6680371B34
6680321B86
RTL4226B
https://www.motorola.com/businessonline
121
8/03
Service Aids,
Manuals
HT600 Series
Service Aids
Radio Interface Box
Links radio programming cable and
computer interface together. Provides
required voltage shift to enable
communications between radio and
computer. Requires computer
interface cable, radio test and
programming cable, and a 9 volt snap type battery (6082728J01),
order separately.
RLN4008E Radio Interface Box
Computer Interface Cable
Used to connect
computer’s serial adapter
to radio interface box.
3080369B71 Cable, RIB to
25 pin D
3080369B72 Cable, RIB to
9 pin D
Controller Flex Extender
Allows access to all electrical
points on the controller flex and
the interior of the RF board for
troubleshooting purposes.
REN4000A
Controller Flex Extender
Wall Mounted Power Supply
Used to supply power to the radio interface box, RLN4008E
0180357A57 Wall Mounted Power
Supply, 110 Volts
0180358A56 Wall Mounted Power
Supply, 220 Volts
Service Aids
Field Modification Kit
Allows for quick field modification of RTX4005 “A” test sets to
provide operation with the HT600 Radio.
RPX4665A Field Modification, RTX4005A
Programming Aid
Enables programming of the DTMF pad from outside of HT600 DTMF
optioned radios.
0180358A59 Programming Aid
Programming Software
Utilizing your personal computer, this software enables you to add or
reprogram frequencies as your requirements change. Compatible
with IBM, XT, AT, Model 30 50, 60 and 80. Requires Radio Interface
Box and proper cables, order separately.
RVN4005H Programming Software, 3-1⁄2˝ diskettes (includes manual
and software box)
Manuals
6881065C75 Service Manual
0180305J46 Ear Microphone System and Temple
Transducer CD-ROM
RLN4008E
3080369B71
REN4000A
01800357A57
RPX4665A
Loading...