Motorola CP150 User Manual

CP150™/CP200
Commercial Series
Two-Way Radio User Guide
Manuel de l'utilisateur
de la radio bidirectionnelle
CONTENTS
Computer Software Copyrights . . . . . . . . . . 2
Safety and Warranty . . . . . . . . . . . . . . . . . 3
Product Safety and RF Exposure
Compliance. . . . . . . . . . . . . . . . . . . . . . . .3
Battery Information . . . . . . . . . . . . . . . . . . . 3
Charging Batteries . . . . . . . . . . . . . . . . . 3
Limited Warranty. . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . 9
Conventional Radio Systems . . . . . . . . . . . 9
CP150™/CP200™ Radio Features . . . . . .9
Radio Wide Features . . . . . . . . . . . . . . . 9
Signaling Features . . . . . . . . . . . . . . . . . 9
Radio Overview . . . . . . . . . . . . . . . . . . . . 11
Parts of the Radio . . . . . . . . . . . . . . . . . . .11
CP150/CP200 Models . . . . . . . . . . . . . 11
On/Off/Volume Knob . . . . . . . . . . . . . .12
Channel Selector Knob . . . . . . . . . . . . 12
Push-to-Talk (PTT) Button . . . . . . . . . . 12
Microphone . . . . . . . . . . . . . . . . . . . . . 12
LED Indicator . . . . . . . . . . . . . . . . . . . . 12
Programmable Buttons . . . . . . . . . . . . 13
Indicator Tones . . . . . . . . . . . . . . . . . . . . . 15
Audio Indicators for Programmable
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Improved Audio Features . . . . . . . . . . . . . 16
Companding . . . . . . . . . . . . . . . . . . . . 16
Getting Started . . . . . . . . . . . . . . . . . . . . 17
Battery Information . . . . . . . . . . . . . . . . . . 17
Charging Your Battery. . . . . . . . . . . . . 17
Wall Charger. . . . . . . . . . . . . . . . . . . . . . . 17
Desktop Chargers. . . . . . . . . . . . . . . . . . . 18
Rapid Charger . . . . . . . . . . . . . . . . . . . 18
Slow Charger. . . . . . . . . . . . . . . . . . . . 19
Accessory Information . . . . . . . . . . . . . . . 20
Attaching the Battery . . . . . . . . . . . . . . 20
Removing the Battery . . . . . . . . . . . . . 20
Attaching the Antenna . . . . . . . . . . . . . 21
Removing the Antenna . . . . . . . . . . . . 21
Attaching the Belt Clip . . . . . . . . . . . . . 22
Removing the Belt Clip . . . . . . . . . . . . 22
Turning the Radio On or Off . . . . . . . . . . . 23
Adjusting the Volume . . . . . . . . . . . . . . . . 23
Selecting a Radio Channel . . . . . . . . . . . . 23
Receiving . . . . . . . . . . . . . . . . . . . . . . . . . 24
Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . 24
Transmitting . . . . . . . . . . . . . . . . . . . . . . . 24
VOX Operation . . . . . . . . . . . . . . . . . . . . . 25
Connecting a VOX Headset . . . . . . . . 25
Enabling or Disabling VOX . . . . . . . . . 25
Enable/Disable Headset Sidetone . . . . . . 25
VOX Headset. . . . . . . . . . . . . . . . . . . . 25
Non-VOX Headset with In-Line PTT . . 26
CONTENTS
1
English
CONTENTS
Repeater or Talkaround Mode . . . . . . . . . 26
Setting Tight or Normal Squelch. . . . . . . . 26
Setting the Power Level . . . . . . . . . . . . . . 27
Radio Calls . . . . . . . . . . . . . . . . . . . . . . . 29
Receiving a Selective Call . . . . . . . . . . . . 29
Receiving a Call Alert Page . . . . . . . . . . . 29
Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Talkback . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Starting System Scan. . . . . . . . . . . . . . . . 31
Stopping System Scan . . . . . . . . . . . . . . . 31
Starting Auto Scan . . . . . . . . . . . . . . . . . . 31
Stopping Auto Scan . . . . . . . . . . . . . . . . . 31
Deleting a Nuisance Channel . . . . . . . . . . 32
Restoring a Channel to the Scan List . 32
Prioritizing a Scan List Member . . . . . . . . 33
Accessories . . . . . . . . . . . . . . . . . . . . . . 35
Carry Accessories. . . . . . . . . . . . . . . . . . . 35
Chargers. . . . . . . . . . . . . . . . . . . . . . . . . . 35
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Headsets . . . . . . . . . . . . . . . . . . . . . . . . . 36
Surveillance Accessories . . . . . . . . . . . . . 36
Remote Speaker Microphones . . . . . . . . . 37
Ear Microphone Systems . . . . . . . . . . . . . 37
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . 38
Miscellaneous. . . . . . . . . . . . . . . . . . . . . . 38

COMPUTER SOFTWARE COPYRIGHTS

The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, repro du ced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, e xcept for the normal non-exclusive license to use that arises by operation of law in the sale of a product.
English
2

SAFETY AND WARRANTY

!
BATTERY INFORMATION
Charging Batteries

PRODUCT SAFETY AND RF EXPOSURE COMPLIANCE

Before using this product, read the operating instructions for saf e usage contained in the Product
C a u t i o n
This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, rea d
the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 68P81095C98) to ensure compliance with RF energy exposure limits.
For a list of Motorola-approved antennas, batteries, and other accessories, visit the following web site which lists approved accessories: http://www.motorola.com/cgiss/ index.shtml.
Safety and RF Exposure booklet enclosed with your radio.
ATTENTION!
This product is powered by a nickel-cadmium (NICd) or lithium-ion (Lilon) rechargeable battery. Charge the battery before use to ensure optimum capacity and performance. The battery was designed specifically to be used with a Motorola charger . Charging in non­Motorola equipment may lead to battery damage and void the battery warranty.
Note: When charging a battery attached to a
radio, turn the radio off to ensure a full charge.
The battery should be at about 77°F (25°C) (room temperature), whenever possible. Charging a cold battery (bel ow 50° F [10°C] ) may result in leakage of electrolyte and ultimately in failure of the battery. Charging a hot battery (above 95°F [35°C]) results in reduced discharge capacity, affecting the performance of the radio. Motorola rapid-rate battery chargers contain a temperature­sensing circuit to ensure that batteries are charged within the temperature limits stated above.
SAFETY AND
WARRANTY
3
English
SAFETY AND
WARRANTY

LIMITED WARRANTY

MOTOROLA COMMUNICATION
PRODUCTS
I. WHAT THIS WARRANTY COVERS AND
FOR HOW LONG:
MOTOROLA INC. (“MOTOROLA”) warrants the MOTOROLA manufactured Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:
CP150/CP200 Portable Units Two (2) Years Product Accessories One (1) Year
Motorola, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the ter ms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA.
This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product.
MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty.
English
4
II. GENERAL PROVISIONS:
III. STATE LAW RIGHTS:
This warranty sets forth the full extent of
MOTOROLA's responsibilities regarding the
Product. Repair, replacement or refund of the
purchase price, at MOTOROLA’s option, is the
exclusive remedy. THIS WARRANTY IS GIVEN
IN LIEU OF ALL OTHER EXPRESS
WARRANTIES. IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION, IMPLIED
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY. IN NO EVENT SHALL
MOTOROLA BE LIABLE FOR DAMAGES IN
EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT, FOR ANY LOSS OF USE, LOSS OF
TIME, INCONVENIENCE, COMMERCIAL
LOSS, LOST PROFITS OR SAVINGS OR
OTHER INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES ARISING OUT
OF THE USE OR INABILITY TO USE SUCH
PRODUCT, TO THE FULL EXTENT SUCH MAY
BE DISCLAIMED BY LAW.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY.
This warranty gives specific legal rights, and there may be other rights which may vary from state to state.
IV. HOW TO GET WARRANTY SERVICE:
You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by Motorola through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call Motorola at 1-800-927-2744 US/Canada.
SAFETY AND
WARRANTY
5
English
SAFETY AND
WARRANTY
V. WHAT THIS WARRANTY DOES NOT
COVER:
A Defects or damage resulting from use of the
Product in other than its normal and customary manner.
B Defects or damage from misuse, accident,
water, or neglect.
C Defects or damage from improper testing,
operation, maintenance, installation, alteration, modification, or adjustment.
D Breakage or damage to antennas unless
caused directly by defects in material workmanship.
E A Product subjected to unauthorized
Product modifications, disassemblies or repairs (including, without limitation, the addition to the Product of non-Motorola supplied equipment) which adversely affect performance of the Product or interfere with Motorola's normal warranty inspection and testing of the Product to verify any warranty claim.
F Product which has had the serial number
removed or made illegible.
G Freight costs to the repair depot.
H A Product which, due to illega l or
unauthorized alteration of the software/ firmware in the Product, does not function in accordance with MOTOROLA’s published specifications or the FCC type acceptance labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA.
I Scratches or other cosmetic damage to
Product surfaces that does not affect the operation of the Product.
J Normal and customary wear and tear.
VI.PATENT AND SOFTWARE PROVISIONS:
MOT OROLA will def end, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:
A that MOTOROLA will be notified promptly in
writing by such purchaser of any notice of such claim;
English
6
B that MOTOR OLA will hav e sole control of the
defense of such suit and all negotiations for its settlement or compromise; and
C should the Product or parts become, or in
MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA.
MOTOROLA will have no liability with respect to
any claim of patent infringement which is based
upon the combination of the Product or parts
furnished hereunder with software, apparatus or
devices not furnished by MOTOROLA, nor will
MOTOROLA have any liability f or the use of
ancillary equipment or software not furnished by
MOTOROLA which is attached to or used in
connection with the Product. The foregoing
states the entire liability of MOTOROLA with
respect to infringement of patents by the Product or any parts thereof.
Laws in the United States and other countries preserve for MOT OR OLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such Motorola software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative th e reof. No other use includin g, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTORO LA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights.
VII. GOVERNING LAW:
This Warranty is governed by the laws of the State of Illinois, USA.
SAFETY AND
WARRANTY
7
English
SAFETY AND
Notes:
WARRANTY
English
8

INTRODUCTION

CONVENTIONAL RADIO SYSTEMS

Conventional radio systems typically refer to unit-to-unit communications through a single channel. Conventional systems also allow radio users to extend communication coverage by relaying their messages through a repeater. To ensure coordinated use by multiple users, each radio user must monitor the channel or repeater before transmitting to verify that the system is not currently busy.
Monitor and Sticky Monitor
System Scan with Single Priority Scan
Signaling Features
MDC 1200 Signaling (Available for 4W & 5W models only)
- Selective Radio Inhibit Decode
- Radio Check Decode
Quik-Call II Signaling (Available for 4W & 5W models only)
- PTT ID Decode
- PTT ID Encode
- Selective Inhibit Decode

CP150™/CP200™ RADIO FEATURES

Radio Wide Features
4 or 16 Channels
2 Programmable Feature Buttons
Busy Channel Lockout
High/Low Po wer Settings (A v ailable f or 4W & 5W models only)
Repeater/Talkaround
Voice Operated Transmit
Transmit Time-Out Timer
- Call Alert Decode
DTMF Signaling
- DTMF PTT ID Encode
- Selective Call Decode
INTRODUCTION
9
English
Notes:
INTRODUCTION
English
10

RADIO OVERVIEW

PARTS OF THE RADIO

CP150/CP200 Models
On/Off/Volume
Knob
RADIO OVERVIEW
Push-to-Talk
(PTT) Button
Side Button 1
(programmable)
Side Button 2
(programmable)
Channel Selector
Knob
LED Indicator
Microphone
Accessory Connector with a Dust Cover
11
English
RADIO OVERVIEW
On/Off/Volume Knob
Turns the radio on or of f, and adjusts the radio’s volume.
Channel Selector Knob
Switches the radio to different channels.
Push-to-Talk (PTT) Button
Press and hold down this button to t alk (transmit); release it to listen.
Microphone
When sending a message, hold the microphone 1 to 2 inches (2.5 to 5 cm) away from your mouth, and speak clearly into it.
LED Indicator
Indicates power-up, transmit, receive, scan status, Call Alert™, Selective Call, Monitor, and battery status.
Basic Features
LED State/Color Indication
Red Transmitting Flashing Red Receiving
Scan
Flashing Green Scanning for activity
Call Alert
Flashing Yellow Indicates receiving a Call Alert
Selective Call
Flashing Yellow
Sticky Monitor/Open Squelch
Yellow While monitoring
Low Battery
Flashing Red when transmitting
†Available for 4W and 5W models only.
Indicates receiving a Selectiv e Call
Low battery leve l
English
12
Battery Charge Status
You can check battery charge status if your dealer has preprogrammed one of the programmable buttons. Hold down the preprogrammed Battery Indicator button. The charge status is shown by the color of th e radio’s LED indicator.
Battery
Level
Good Green Sufficient Yellow Low Flashing Red Very Low None
LED
Indicator
Programmable Buttons
The two side buttons on your radio can be programmed by your dealer as shortcuts to various radio f eatures.
Check with your dealer for a complete list of functions your radio supports.
Some buttons can access up to two features, depending on the type of button press:
short press — quickly pressing and releas­ing the programmable buttons
long press — pressing and holding the programmable buttons for a period of time (default 1 1/2 seconds or programmed value) before releasing
hold down — pressing and holding down the programmable buttons while checking status or making adjustments
Depending on how your radio has been programmed by your dealer, these functions are activated EITHER through a short press OR a long press, but NOT both.
A summary of programmable radio features and corresponding page references appears beginning on page 14.
In the “Feature” column, ha v e your dealer write down the programmable buttons next to the features that have been programmed to them.
RADIO OVERVIEW
13
English
Feature Short Press/Long Press Hold Down Page Button
RADIO OVERVIEW
Battery Indicator
Sticky Monitor/ Monitor
Volume Set Sounds a tone for adjusting the radio’s volume level. 23
Voice Operated Transmission (VOX)
Power Level
Repeater/ Talkaround
Squelch
†Available for 4W and 5W models only.
A long press of the Monitor button initiates. A short press of the Monitor button cancels.
Toggle VOX on and off. 25
T oggles y our radio’s transmit po wer
level between High and Low power.
Toggles between using a repeater and transmitting directly to another radio.
Toggles your radio’s squelch level between tight and normal squelch.
Checks the battery charge status. 13
Monitors the selected channel for any activity.
—27
—26
—26
24
English
14
Feature Short Press/Long Press Ho ld Down Page Button
Scan Starts or stops the Scan operation. 31
RADIO OVERVIEW
Nuisance Channel Delete
Deletes a nuisance channel while scanning.

INDICATOR TONES

High pitched tone Low pitched tone
Self Test Pass Tone
Self Test Fail Tone
Positive Indicator Tone
Negative Indicator Tone
—31

AUDIO INDICATORS FOR PROGRAMMABLE BUTTONS

Some programmable buttons use tones to indicate one of two modes:
Button
Scan Start scan Stop scan Power Level Squelch Tight squelch Normal squelch
Repeater/ Talkaround
VOX VOX enabled VOX disabled †Available for 4W and 5W models only.
Positive
Indicator Tone
High power
selected
Does not use repeater
Negative
Indicator T one
Low power
selected
Uses repeater
15
English
RADIO OVERVIEW

IMPROVED AUDIO FEATURES

Companding
Companding is a feature that allows further improvement of voice quality. It compresses your voice at transmission, and expands it when receiving while simultaneously reducing extraneous noise. However, to enjoy this benefit, all transmitting and receiving radios must have this feature activated.
English
16

GETTING STARTED

BATTERY INFORMATION

Charging Your Battery
If a battery is new, or its charge level is very low, you will need to charge it before you can use it. When the battery level is low and the radio is in transmit mode you will see the LED indicator flash red. Upon release of the PTT button, you will hear an alert tone.
Note: Batteries are shipped uncharged from
the factory. Always charge a new battery 14 to 16 hours before initial use, regardless of the status ind icated by the charger.
Note: Do not use the wall charger and
desktop charger at the same time when charging.

WALL CHARGER

Note: Do not use the wall charger if using
lithium-ion (Li-Ion) or nickel-metal hyride (NiMH) batteries. The wall charger is for nickel-cadmium (NiCd) batteries only.
To Charge the Battery
1 Turn the radio off. 2 Lift the dust cover to expose the audio
accessory connector.
3 Insert the charging adapter into the
accessory connector.
4 Plug the charging adapter into an electr ical
outlet.
The LED on the charging adapter lights Red while the charger is plugged into an electrical outlet.
Note: Do not leave the charger connected
to the radio when it is not connected to the electrical outlet.
5 Unplug the charger from the electrical outlet
and radio after 10 hours. Note: After the initial charge of 14 to 16
hours, do not charge the battery more than 10 hours.
GETTING STARTED
17
English
GETTING STARTED

DESKTOP CHARGERS

Rapid Charger
1 Turn the radio off. 2 Place the battery, with or without the radio, in
the charger pocket.
The charger LED indicates the charging progress.
LED color Status
No LED Indication Battery inserted incorrectly
or battery not detected.
Single Green Flash Successful charger
power-up.
Flashing Red
Steady Red Battery is in Rapid charge
Flashing Yellow Battery in charger but wait-
*
Battery unchargeable or not making proper contact.
mode.
ing to be charged. The bat­tery temperature may be too hot or too cold. The voltage may be lower than the pre­determined threshold level for charging.
LED color Status
Flashing Green
Green Battery fully charged.
* Remove the battery from the charger and
use a pencil eraser to clean the three metal contacts at the back of the battery. Place the battery back into the charger. If the LED indicator continues to flash red, replace the battery.
† A standard battery may require 90 minutes to
charge to 90% capacity. Even though new batteries might prematurely indicate a full charge (steady green LED), charge the battery for 14 to 16 hours prior to initial use for best performance.
Battery 90% (or more) charged. Trickle charging.
A list of Motorola authorized batteries and battery chargers appears on page 35. The listed chargers will charge only Motorola authorized batteries. Other batteries may not charge.
English
18
Slow Charger
1 Turn the radio off. 2 Place the battery, with or without the radio, in
the charger pocket.
The charger LED indicates the charging progress.
LED color Status
No LED Indication Battery inserted incorrectly
or battery not detected.
Steady Red Battery is in over night
charge mode. The battery is fully charged after 11 hours.
GETTING STARTED
19
English

ACCESSORY INFORMATION

Attaching the Battery
Removing the Battery
Battery Latch
GETTING STARTED
English
1 Align the battery to the battery rails on the
back of the radio (approximately 1/2 in. from the top of the radio.)
2 Press the battery firmly to the radio and slide the
battery upward until the latch snaps into place.
3 Slide the battery latch, located on radio bottom,
into the lock position.
20
1 Turn off the radio if it is turned on (see page 23). 2 Slide the battery latch into the unlock position.
Disengage by pushing downward and holding the latch towards the front of the radio.
3 With the battery latch disengaged, slide the
battery down from the top of the radio about 1/2 in. Once the battery is free from the battery rails, lift it directly away from the radio.
Attaching the Antenna Removing the Antenna
GETTING STARTED
Turn the antenna clockwise to attach it. Turn the antenna counter-clockwise to remove
it.
21
English
GETTING STARTED
Attaching the Belt Clip Removing the Belt Clip
Belt Clip Tab
English
1 Align the grooves of the belt clip with those of
the battery.
2 Press the belt clip downward until you hear a
click.
22
1 Use a key to press the belt clip tab away from
the battery to unlock the belt clip.
2 Slide the belt clip upward to remove it.

TURNING THE RADIO ON OR OFF ADJUSTING THE VOLUME

1 Hold down the Volume Set button (see page
14); you will hear a continuous tone.
2 Turn the On/Off/V olume Co ntr ol knob to the
desired volume level.
ON OFF
Turn the On/Off/ Volume Control
knob clockwise. If power-up is successful, you will hear the Self-Test Pass Tone ( ) and see the LED flash green.
If the radio fails to power up, you will hear the Self Test Fail Tone ().
Turn the On/Off/ Volume Control knob counter-clockwise until you hear a click.
3 Release the Volume Set button.
GETTING STARTED

SELECTING A RADIO CHANNEL

Your radio offers 4 or 16 channels. Note: Due to government regulations, some
channels may not be programmed. Ask your dealer for more information.
To select a channel, turn the Channel Selector knob clockwise or counterclockwise until you reach the desired channel.
23
English

RECEIVING

1 Turn your radio on. 2 Adjust the radio’s volume (see page 23). 3 Switch to the desired channel. To respond,
hold the radio in a vertical position, press the PTT, and talk at a distance of about 1 to 2 inches (2.5 to 5 cm) from the microphone.
A short press of the Monitor button cancels Sticky Monitor mode and returns the radio to normal operation.

TRANSMITTING

1 Turn your radio on. 2 Use the Channel Selector knob to select the
desired channel.
GETTING STARTED
English

MONITORING

It is important to monitor traffic before transmitting to ensure that you do not “talk over” someone wh o is already transmitting.
1 Press and hold the preprogrammed
Monitor button to access channel traffic.
2 Once channel traffice has cleared, proceed
with your call by pressing the PTT butto n.
3 A long press of the preprogrammed Monitor
button places the radio in Sticky Monitor mode.
You hear a high-pitched tone.
24
3 Hold the radio in a vertical position, press the
PTT, and talk at a distance of about 1 to 2
inches (2.5 to 5 cm) from the microphone.
4 Release the PTT to listen.

VOX OPERATION

When hands-free operation is desired, your radio can be activated b y v oice alone usin g the VOX feature when you speak through an accessory that is connected to your radio.
Connecting a VOX Headset
1 Turn off your radio. 2 Connect the VOX accessory to your radio and
turn the radio on.
You can select channels to enable or disable VOX as preprogrammed by your dealer.
1 Select a channel that has been
preprogrammed by your dealer to enable VOX.
Note: Pressing the PTT button disables
VOX.
2 Select a channel that has not been
preprogrammed by your dealer to disable VOX.
GETTING STARTED
Enabling or Disabling VOX
To enable or disable VOX operation, press the preprogrammed VOX button (see page 14).
Note: Pressing the PTT button disables VOX.
– or –

ENABLE/DISABLE HEADSET SIDETONE

Your dealer can program your r adio so you can hear your voice through a headset while you speak.
VOX Headset
1 Turn off your radio. 2 Connect the VOX accessory to your radio. 3 Turn the radio on. During transmit, you will
hear your voice through the headset while you speak.
25
English
4 To disable the headset sidetone, turn off your
radio and turn the radio on again.
Non-VOX Headset with In-Line PTT

REPEATER OR TALKAROUND MODE

Talkaround Mode enables you to commu nicate with another radio when either:
GETTING STARTED
English
1 Turn off your radio. 2 Connect the non-VOX accessory to your
radio.
3 Press and hold the In-line PTT on your
headset.
4 Turn the radio on and release the PTT once
the radio has completed start-up. During transmit, you will hear your voice through the headset while you speak.
5 To disable the headset sidetone, turn off your
radio and turn the radio on again.
26
the repeater is not operating
– or –
your radio is out of the repeater’s range but within communicating distance of another radio.
Press the preprogrammed Repeater/ Ta lkaround button (see page 14) to toggle between Repeater mode and Talkaround Mode.

SETTING TIGHT OR NORMAL SQUELCH

Use this feature to filter out nuisance (unwanted) calls and/or background noise. Howe ver, tightening squelch could cause calls from remote locations to be filtered out as well. In this case, normal squelch may be more desirable.
Press the preprogrammed Squelch button (see page 14) to toggle between tight and normal squelch.

SETTING THE POWER LEVEL

(Available for 4W and 5W models only)
Each channel in your radio has a predef ined transmit power level that can be changed.
High power allows you to reach a radio that is farther away.
Low power conserves the battery’s charge.
Press the preprogrammed Power Level button (see page 14) to toggle between lo w and high power.
GETTING STARTED
27
English
GETTING STARTED
Notes:
English
28

RADIO CALLS

RECEIVING A SELECTIVE CALL

(Available for 4W and 5W models only)
When you receive a Selective Call:
The LE D ind ica to r flas he s yellow, if pro­grammed by your dealer.
You hear two high pitched tones.
1 To acknowledge the call, press and release
the PTT button.
2 Press and hold the PTT button to talk;
release to listen.

RECEIVING A CALL ALERT PAGE

(Available for 4W and 5W models only)
When you receive a Call Alert page:
The LE D ind ica to r flas he s yellow, if pro­grammed by your dealer.
You hear four high pitched tones.
To acknowledge the page, press and release the PTT button; to cancel the page, press any other key.
RADIO CALLS
29
English
Notes:
RADIO CALLS
English
30
SCAN
Your radio is equipped with the Scan feature, which allows you to monitor multiple channels for voice activity. The radio will stop on a channel when it detects activity on it.
Your radio automatically s witches to a channel within the scan list when it detects activity.
The LED indicator blinks green during a scan operation and stops blinking when the radio switches to a channel.
There are two types of Scan available in your radio:
•System Scan
Auto Scan

TALKBACK

The Talkback feature allows you to respond to a transmission while scanning. If a transmission is detected on a channel while scanning, the radio will stop on that channel for a default period of time after activity has ceased. This is referred to ashangtime. During this hangtime you may respond by pressing the PTT button.
Note: The LED scan indicator stops blinking
while the radio is in hangtime. If the PTT button is not pressed during the preprogrammed hangtime, the radio returns to scanning channels.

STARTING SYSTEM SCAN

Press the preprogrammed Scan button (see page 14).

STOPPING SYSTEM SCAN

Press the preprogrammed Scan button.

STARTING AUTO SCAN

Auto Scan automatically starts scanning once a channel with Auto Scan enabled is selected.
Select the channel that your dealer has preprogrammed for Auto Scan.

STOPPING AUTO SCAN

Select a channel that has not been preprogrammed for Auto Scan.

SCAN

31
English

DELETING A NUISANCE CHANNEL

Restoring a Channel to the Scan List
SCAN
Note: Your dealer must preprogram a button
to Nuisance Delete (see page 14) to access this feature.
If a channel continually generates unwanted calls or noise (a “nuisance” channel), you can temporarily remove it from the scan list:
1 While the radio is on the Nuisance Channel,
press the preprogrammed Nuisance
Channel Delete button until you hear a tone.
2 Release the Nuisance Channel Delete
button. The nuisance channel is deleted. Note: You cannot temporarily delete the
channel that has been prepro­grammed as your designated scan channel, a priority channel, or the last remaining channel in the scan list.
1 Power off the radio. Once the radio is powered
on again, the deleted nuisance channels are restored to the scan list.
or
1 Press the preprogrammed Scan button to stop
the scan.
2 Press the preprogrammed Scan button again
to start scanning again. The Deleted Nuisance Channels are restored to the scan list.
or
1 Select a different channel. Once you return to
the original channel, the deleted nuisance channels are restored to the scan list.
English
32

PRIORITIZING A SCAN LIST MEMBER

You may want your radio to scan a specific channel more frequently for calls. Your dealer can prioritize scan list members for you. Check with your dealer for details.
Priority Channel Scanning Sequence
None specified Ch1➠Ch2➠Ch3➠
Ch4➠...Ch1
Channel 2 Ch2Ch1➠Ch2Ch3
Ch2Ch4➠Ch2...Ch1
Even though your radio has switched to a non­priority channel, it will still check for activity on the priority channel. If ac tivity is dete cte d , the radio will switch to the priority channel.
SCAN
33
English
SCAN
Notes:
English
34
35
ACCESSORIES

HEADSETS

RLN5411 Ultra-Lite Breeze Behind the Head
Headset PMMN4001 Ultra-Lite Earset with Mic and PTT HMN9013 Lightweight Headset w/o In-line PTT RMN4016 Lightweight Headset with In-line PTT RLN5238 Lightweight Headset with In-line PTT ,
NFL Style HMN9021 Medium Weight Over the Head Dual
Muff Headset HMN9022 Medium Weight Behind the Head
Dual Muff Headset BDN6647 Medium Weight Single Speaker
Headset BDN6648 Heavy Duty Dual Muff Headset with
Noise Canceling Microphone RMN5015 Heavy Duty Dual Muff Racing
Headset (requires RKN4090
Headset Adapter Cable) RMN4051 2-Way Hard Hat Mount, Black, Noise
Reduction Rating (22 dB) (requires
RKN4094) RMN4054 Receive-Only Hard Hat Mount
Headset w/3.5mm Right Angle Plug RMN4055 Receive-Only Headband Style
Headset w/3.5mm Right Angle Plug
RKN4090 Adapter Cable (for use with headset
RMN5015)
RKN4094 In-Line PTT Adapter (for use with
headset RMN4051)
REX4648 Replacement Foam Ear Pad and
Windscreen Kit (for use with headsets RMN9013 & RMN4016)
7580376E34 Replacement Ear Seals (for use with
headsets HMN9021 & HMN9022)
5080371E66 Replacement Ear Pad (for use with
headset BDN6647)
3580371E59 Replacement Wind Screen (for use
with headset BDN6647)

SURVEILLANCE ACCESSORIES

HMN9752 Earpiece with Volume Control,
1-Wire (plastic earloop) (Beige)
HMN9727 Earpiece without Volume Control,
1-Wire (plastic earloop) (Beige)
RLN4894 Earpiece without Volume Control,
1-Wire (plastic earloop) (Black)
HMN9754 Earpiece with Microphone & PTT
Combined, 2-Wire (Beige)
RLN4895 Earpiece with Microphone & PTT
Combined, 2-Wire (Black)
English
36
RLN5198 Earpiece with Microphone & PTT
Combined, 2-Wire w/Low Noise Kit NTscn(83)-7.3(71 (Beige))]TJ-8.1429 -1.6241 TD0 Tc-0.0524 Tw[(BDN67)-7.9(2)-0.4(0)-3797.4(F)-5.5(le)22.2(xib)22.2(l)-3cne Ear Receiver without Volume
CR
HMN9036 Earbud with Microphone & PTT
Cmbined, 2-Wire (Black)
HLN9132 Earbud Single Wire Receiv
(Black) NT8370 Extrem NT(8371)-3857.5(L)-7.9(o)14.6(w Noise)-7.9( K)5.3(i)-3cnt RLN4760 Small Custom Clear Earp
Right Ear (for use with low noise kit
NTsc3(83)-7.6(71))]TJ-8.1429 -1.6316 TD0.001 Tc-0.0008 Tw[(RLN)-6.3(4763)-3909.2(Small Custom Clear Ear)-34.4(p)0cniece
ACCESSORIES

REMOTE SPEAKER MICROPHONES

Left Ear (fw noise kit NTsc3(83)-7.6(71))]TJ-8.1429 -1.6316 TD0.0002 Tc[(RLN)-7.1(4761)-3910(Me)-7.7(dium C)-7.1(u)-0.2(stom)-8.9( Clea)-7.7(r Ear)-27.7(p)-0.2(iece)14.8(, )]TJ8.1429 -1.2481 TD0 Tc0.0002 Tw[(R)-7.3(i)4(ght)-7.7( E)5.3(a)-7.9(r (f)29.9(or use with lo)14.6(w)-7.3( noise kit)-7.7( )]TJ0 -1.2556 TD0.0003 Tc0 Tw[(N)-.1(Tsc3(83)-7.6(71))]TJ-8.1429 -1.6316 TD0.0002 Tc[(RLN)-7.1(4764)-3910(Me)-7.7(dium C)-7.1(u)-0.2(stom)-8.9( Clea)-7.7(r Ear)-27.7(p)-0.2(iece)14.8(,)]TJ8.1429 -1.2481 TD0.0007 Tc-0.0005 Tw[(L)-7.2(e)0.3(ft Ear (f)30cnor use with lo)15.3(w noise )-7.5(kit )]TJ0 -1.2556 TD-0.0002 Tc0 Tw[(N)-..5(T)1.8((83)-8.1(71) )]TJ-8.1429 -1.6316 TD0.0007 Tc-0.0005 Tw[(RLN)-6.6(4762)-3909.5(L)-7.2(a)0.3(rge Cu)-7.2(stom C)-6.6(l)4..1ear Ear)-27.2(p)0c3iece
Right Ear (for use with low noise kit NTsc3(83)-7.6(71))]TJET136.56 179.4 292.56 -0.48 ref136.08 244.38 293.52 -0.48 ref136.56 388.02 292.56 -0.48 ref136.08 388.02 0.48 -209.1 ref169.08 388.02 0.48 -209.1 ref192.12 388.02 0.48 -209.1 ref215c1 388.02 0.48 -209.1 ref238.08 388.02 0.48 -209.1 ref251.1 388.02 0.48 -209.1 ref264.12 388.02 0.48 -209.1 ref297.12 388.02 0.48 -209.1 ref330.12 388.02 0.48 -209.1 ref363.12 388.02 0.48 -209.1 ref396.12 388.02 0.48 -209.1 ref429.12 388.02 0.48 -209.1 refBT0 7.98 -7.98 0 144.66 403.44 Tm0.0007 Tc-0.0005 Tw[(RLN4)-7.2(765)-3901.9(La)-7.2(rge Cu)-7.2(stom C)-6.6(l)4..1ear Earp
Left Ear (fw noise kit NTsc3(837)-7.6(1))]TJ-8.1353 -1.6241 TD0.0001 Tc-0.03 Tw[(508038)-7.8(4F72)-2511.6(R)-7.2(eplacement Noise A)5.4(t)-0.1(t)-7.6(e)-0.3(n)14.7(u)-0.3(a)-7.8(t)-0.1(ing P)5.4(l)-3c5(ug )]TJ8.1353 -1.2556 TD-0.0004 Tc0.0006 Tw[(f)29.5(o)-8.3(r NT)-5.9(8370)]TJ-8.1353 -1.6316 TD0.0007 Tc-0.0005 Tw[(508037)-7.2(1E73)-2450c8REar Tip (for use with
low noise kit NT(8371) (Beige))]TJ-8.1353 -1.6316 TD[(508037)-7.2(1E75)-2450c8REar Tip (for use with
low noise kit NT(8371) (Blac)19.5(k)4.5())]TJ-8.1353 -1.6241 TD[(758037)-7.2(2E11)-2450c8REar Cushion (f

EAR MICROPHONE SYSTEMS

HMN9030 er Microphone with
37
HKN9094 RCord (f
English
0180358B38 Ring Push-to-Talk Switch (for use
with ear microphone systems BDN6646 & BDN6706)
0180300E83 Body Switch Push-to-Talk (for use
with ear microphone systems
BDN6646 & BDN6706) 0180300E25 Ear Guard with Adjustable Loop 0180358B32 Ear Holder, Black, Small 0180358B33 Ear Holder, Black, Medium 0180358B34 Ear Holder, Black, Large 0180358B35 Ear Holder, Clear, Small 0180358B36 Ear Holder, Clear, Medium 0180358B37 Ear Holder, Clear, Large

ANTENNAS

MISCELLANEOUS

RLN5500 Accessory Retainer Kit (for use with
any audio accessory that needs to be secured to the radio due to demanding customer environments)
TDN9327 Portable Radio Hanger for door
panels up to 2.75 inch (slides over and hangs from the door panel in vehicle, radio belt clip required)
TDN9373 Portable Radio Hanger for door
panels up to 2.75 to 3.25 inch (slides over and hangs from the door panel in vehicle, radio belt clip required)
ACCESSORIES
English
NAD6502_R VHF Heliflex Antenna 14cm,
146-174 MHz HAD9742 VHF Stubby Antenna, 9cm,
146-162 MHz HAD9743 VHF Stubby Antenna, 9cm,
162-174 MHz NAE6522_R UHF Heliflex Stubby Antenna 9cm,
438-470 MHz 8505816K26 UHF Heliflex Stubby Antenna 7.1cm,
470-520 MHz NAE6483_R Flexible Whip Antenna, 403-520 MHz
38
LED Indicators
LED State/Color Indication
Red Flashing Red
Scan
Flashing Green
Low Battery
Flashing Red while transmitting
Call Alert
Flashing Yellow
Selective Call
Flashing Yellow
Sticky Monitor/ Monitor
Yellow
Battery Charge Status
Green Yellow Flashing Red None
†Available for 4W and 5W models only.
Transmitting Receiving
Scanning for activity
Low battery level
Indicates receiving a Call Alert
Indicates receiving a Selective Call
While monitoring.
Good Sufficient Low Very Low
CP150™/CP200™ Quick Reference Card
On/Off/Volume Knob
Channel Selector Knob
PTT
SP:
1
LP:
SP:
2
LP:
NOTE: Enter the functions for your radio’s two
programmable buttons in the box es provided above .
SP represents Short Press, while LP represents Long Press.
LED
Indicator
Microphone
Turning On the Radio
• Turn On/Off/Volume Control knob clockwise. If the radio successfully powers up, you will hear the Self Test Pass tone and see the LED light green. If the radio fails to power up, you will hear the Self Test Fail tone.
Turning Off the Radio
• Turn On/Off/Volume Control knob counter­clockwise until you hear a click.
Adjusting the Radio Volume
1. Press and hold Volume Set button (preprogrammed by your dealer) until you hear a continuous tone.
2. Turn On/Off/Volume Control knob to adjust volume level.
3. Release Volume Set button at desired volume level.
Selecting a Radio Channel
• Turn Channel Selector knob clockwise or counter­clockwise to reach desired channel.
Receiving
1. Turn on the radio.
2. Adjust the volume level.
3. Select the radio channel.
Transmitting
1. With radio on, turn Channel Selector knob to required channel.
2. Press PTT and speak clearly with mouth about 2.5 to 5 cm (1 to 2 inches) away from microphone.
3. Release PTT when call is completed.
Audio Indicators for Programmable Buttons
Programmable
Buttons
Scan
Power Level
Squelch
Repeater/ Talkaround
VOX VOX enabled VOX disabled †Availab le for 4W and 5W models only.
Positive
Indicator
Tone
Start Scan
operation Radio transmits
at high power Radio operates
in tight squelch Radio DOES
NOT use the repeater
Negative Indicator
Tone
Stop Scan
operation Radio transmits
at low power Radio operates
in normal squelch
Radio uses the repeater
Starting or Stopping Scan
1. Press the preprogrammed Scan button to start scan. The LED indictor blinks green during scan operation. Or, select a channel that has been preprogrammed for Auto Scan to start scan.
2. Press the Scan button again to stop scan. Or, select
a channel that has not been preprogrammed for Auto Scan to stop scan.
Deleting a Nuisance Channel
1. With radio on a Nuisance Channel, press and hold the preprogrammed Nuisance Delete button until you hear a tone.
2. Release the Nuisance Delete button.
MOTOROLA, the Stylized M Logo, and Radius are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners. © Motorola, Inc. 2002, 2003. All rights reserved. Printed in U.S.A.
MOTOROLA, le logotype au M stylisé et Radius sont enregistrés auprès du Bureau des marques et brevets des États-Unis. Tous les autres noms de produits et de services sont la propriété de leurs titulaires respectifs. © Motorola, Inc. 2002, 2003. Tous droits réservés. Imprimé aux États-Unis.
*6880309N60*
6880309N60-A
Loading...