Mitutoyo 02AZD730D, 02AZD880D rev manual

！



！



！



U-WAVE-T

Introduction

The U-WAVE-T is a wireless communication tool for transmitting measurement data to the Mitutoyo
U-WAVE-R (option) by connecting to a Digimatic-output interfaced tool with the supplied connecting
cable. The U-WAVE-T is also categorized into two types: IP67 type and buzzer type. To obtain the
highest performance and the longest service life from the U-WAVE-T, carefully read this User’s Manual
thoroughly prior to use. After reading this manual, keep it near the U-WAVE-T for quick reference. The
specifications of the U-WAVE-T and descriptions in this manual are subject to change without prior
notification.

Safety Precautions

Use the U-WAVE-T in conformance with the specifications, functions and precautions for use given in this
manual. If the U-WAVE-T is used in other way, it may jeopardize safety.

WARNING

Notes on Export Regulations

WARNING

Precautions for the Wireless Law
The U-WAVE-T can use in Japan, EU member countries, U.S.A, Canada .

The U-WAVE-T cannot be used in countries other than Japan, EU member countries, U.S.A, Canada

WARNING

• Remove the battery before taking an airplane and do not use the U-WAVE-T

This device complies with Part 15 of the FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.

Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

Notes

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications, However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is

-- Consult the dealer or an experienced radio/TV technician for help.

Precautions on Wireless Communication Environments

Notice that performance of the U-WAVE-T may not be fully delivered depending on the environment
such as a midway obstruction.
For the items of obstruction factors refer to the following table.

1) The U-WAVE-T may not be able to communicate in the case.

Concrete wall

Metallic partition, etc.
Wireless LAN, Bluetooth

ZigBee, microwave oven,
and other communication
devices

Machine tools, etc.

2) The U-WAVE-T may influence on the peripheral equipment in the case

Medical device

• Do not use the U-WAVE-T near a medical device that has a possibility of causing a

malfunction due to radio waves.

• The U-WAVE-T using an electric wave has a possibility that communication is interrupted
under the influence of external noises, etc., even within the distance of communication of the
electric wave. In this case take sufficient failure prevention action (security measures).

• In the event the U-WAVE-T should fail, take sufficient failure prevention action (security
measures).

• Do not disassemble, short, modify, or heat the supplied battery. The leaked contents may get
into your eyes. Also, heat generation or explosion may result.

• The battery used in the U-WAVE-T contains an irritating substance.
Should this liquid substance be applied to your eyes or skin by accident, immediately rinse it
away in clean water.

• Should the battery be swallowed by accident, immediately rinse the mouth out and induce
vomiting the battery while drinking a large amount of water. After then consult a doctor.

The U-WAVE-T falls into the Catch-All-Controlled Goods or Program under the Category 16 of
the Separate Table 1 of the Export Trade Control Order or the Category 16 of the Separate
Table of the Foreign Exchange Control Order, based on the Foreign Exchange and Foreign
Trade Law of Japan.
Further, this User's Manual also falls into the Catch-All-Controlled Technology for use of the
Catch-All-Controlled Goods or Program, under the Category 16 of the Separate Table of the
Foreign Exchange Control Order.
If you intend re-exporting or re-providing the product or technology to any party other than
yourself, please consult with Mitutoyo prior to such re-exporting or re-providing.

・ The U-WAVE-T must follow the corresponding regulation which is specified in the country

to use an electric wave.

• Do not disassemble or modify any part of the U-WAVE-T.

• Do not peel off the certification label stuck on the U-WAVE-T.

The use of any U-WAVE-T without the label is prohibited.

in the airplane. The use of a wireless equipment in the airplane is prohibited.

undesired operation.

connected.

Item Description

Disables communication if the U-WAVE-T is completely enclosed
with a concrete wall.

Have the possibility of reducing the communication speed or
blocking communication.

Have the possibility of reducing the communication speed or
blocking communication. Separate the communication channel
(band ID) and installation site of each device as far as possible
from those of the U-WAVE-T.

In the worksite operated with machine tools such as electrical
discharge Machines, crane for transfer, arc welding etc.,
have the possibility of reducing the communication speed or
blocking communication.

Item Description

Do not use the U-WAVE-T near a medical device such as a laser
surgical knife and a bathroom scale.

User’s Manual

No.99MAL108B5

Precautions for Dust and Water Resistance

To obtain the highest performance from the IP67 type U-WAVE-T, be sure to observe the following
precautions.

IMPORTANT

• The dust and water resistance of the U-WAVE-T is assured under the condition where the connecting
cable is connected and the battery cover is mounted.
If the U-WAVE-T is not used for an extended period, store it with each cover mounted to prevent from
water and oil.

• To deliver the maximum performance of protection against water and dust (IP67), mount the battery
cover tightly with screws after setting the battery. Also, do not remove the packing from the cover.

• If the connecting cable sheath is broken, a liquid will infiltrate into the U-WAVE-T and a Measuring
tool due to capillary phenomenon, resulting in trouble. Immediately replace the cable.

• Use the U-WAVE-T with sufficient care so that the packing on each part may not be damaged with
cutting chips, dirt, etc. Should any packing be damaged, the dust and water resistance will be
impaired. Immediately replace the packing or have the U-WAVE-T repaired by a service center.

• Rubber and other materials used for rubber caps and sealing portions are not fully effective for
diversified coolants, chemicals, etc. If these materials become deteriorated markedly, consult the
nearest Mitutoyo sales office.

• The U-WAVE-T is provided with such a structure that cannot be disassembled by applying seals to
individual parts.
If any sealed part is disassembled, then a predetermined performance will not be delivered.

• Do not use the U-WAVE-T at sites which might be submerged. The U-WAVE-T cannot prevent liquids
such as a coolant from infiltrating.



TIP

IP67 protection level (For details refer to IEC 60529.)

• Protection against foreign matters (Level 6): Protects an object against the ingress of dust and dirt,
and against a full contact with it.

• Protection against water (Level 7): No causing harmful effects when submerged in water for 30
minutes with its bottom end at a depth of 1 m below the surface of water.

Other Precautions

The following deeds and situations will cause a failure or malfunction in the U-WAVE-T.
Care should be exercised.

IMPORTANT

• Do not give a sudden shock such as a drop or apply an excessive force to the U-WAVE-T.

• If the U-WAVE-T is not used more than 3 months, remove the battery from the U-WAVE-T and store it
in a safe place. Otherwise, leaks from the battery may damage the U-WAVE-T.

• Avoid using or storing the U-WAVE-T at sites which are exposed to direct sunlight, excessively high
or low temperature.

• Avoid using or storing the U-WAVE-T at sites where it may be subject to the adhesion of solution
such as acid and alkali or organic solvent.

• If a high-voltage device such as an electro-spark engraving pen is used for the U-WAVE-T, the
internal electronic parts may be damaged.

• Exercise care so as not to apply an undue force or curvature to the connecting cable.

• If the battery voltage has come down, replace the battery ahead of time before the operation
becomes unstable.



Warranty

In the event that the U-WAVE-T should prove defective in workmanship or material, within one year
from the date of original purchase for use, it will be repaired or replaced, at our option, free of charge
upon its prepaid return to us.
This warranty is effective only where the U-WAVE-T is properly installed and operated in conformance
with the instructions in this manual.

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union
and other European countries with separate collection systems)



This symbol on the U-WAVE-T or on its packaging indicates that the U-WAVE-T shall not be treated
as household waste. To reduce the environmental impact of WEEE (Waste Electrical and Electronic
Equipment) and minimize the volume of WEEE entering landfills, please reuse and recycle.
For further information, please contact your local dealer or distributors.



[1] Name of Each Part and External Dimensions (Unit : mm)

1. LED display (green, red, orange) 2. Battery cover             3. Connector cover

4. Device ID label        5. Buzzer holes (for the buzzer type only)  6. Certification label

5. Certification label
(This label is different according to the type.)

2. Battery cover

3. Connector cover

[2] Replacing the Battery

1) Setting the battery

No battery has been set before shipping. After unpacking the U-WAVE-T, set the battery with the
following procedure. When screwing or unscrewing the screws, always use the size 0 screwdriver (No.

05CZA619) of the standard accessory and tighten or loosen them with a torque of 5 to 8 N•cm.
(1) Remove the two mounting screws (M2.5X0.45X3/No. A115-2515C) with the size 0 screwdriver.
(2) Dismount the battery cover.
(3) Orientate the battery plus side toward the cover, slide its one end into the “+” terminal on the

U-WAVE-T, and then insert the other end into the battery retaining claw.
(4) Check that the packing (No. 02AZD734) has been attached correctly to the specified position.
(5) Mount the battery cover.
(6) Tighten the mounting screws with the size 0 screwdriver to fix the cover.
(7) Make sure that no part of the packing is detached.










(1),(6) (3)

2) Removing the battery

To remove the battery, use a small flat-blade screwdriver, etc. Insert the screwdriver between the

battery retaining claw and the battery, and then remove the battery by using the screwdriver as
leverage.

4. Device ID label

6. Buzzer holes
(for the Buzzer type)

1. LED display

0.1 sec interval

0.3 sec interval



3) Low battery alarm

If the battery voltage becomes considerably low, the LED display blinks red and the U-WAVE-T sends
a low battery alarm error to the U-WAVE-R. Immediately replace the battery.
(The buzzer type alarms a low battery voltage with a buzzer sound along with a blinking LED.)
In addition, the battery (CR2032) used as the power supply for the U-WAVE-T has such a property that
the battery voltage is abruptly restored in a period when the battery has been exhausted, if
measurement data is consecutively transmitted at intervals of several seconds. In such cases,
although low battery alarm errors are not output, the LED display becomes dark and the buzzer sound
becomes small gradually. In such cases, replace the battery immediately.

IMPORTANT

• Always use the CR2032 battery (lithium battery).

• The battery supplied at the time of purchase is to check the functions and performance of the
U-WAVE-T. The predetermined length of life may not be met.

• Even for the used CR2032 battery, its voltage may recover in a short time after it is removed from
the U-WAVE-T. However, do not continue to use the old battery. Be sure to replace the battery

with a new one.

• Upon disposal of the battery comply with the related ordinance, regulation, etc.

• When removing or setting the battery, exercises care so as not to break or bend the battery terminal
by applying an undue force to it. Especially, if a broken piece of the battery terminal should enter
the U-WAVE-T, a failure may be caused.

[3] Connect the Connecting cable to U-WAVE-T

• After loaded with the battery, connect the connecting cable (option, details see section 8)

IMPORTANT

When installing the U-WAVE-T using the connecting cable (02AZD790A, B), particularly
pay attention to the cable orientation. If the cable is connected in the reverse orientation,
data cannot be transmitted.

Black-marked side => U-WAVE-T

DATA switch

Gray-marked side => Measuring tool

Black

Measuring tool side

U-WAVE-T side

(The connector shape and color differs depending on the
Measuring tool to be used. )

• Set up the connecting cable with the following procedure.

When screwing or unscrewing the screws, always use the size 0 screwdriver of the

standard accessory and tighten or loosen them with a torque of 5 to 8 N•cm.

(1) Remove the two mounting screws (M1.7X0.35X2.5/No.A115-1712C) of the connector cover with

the size 0 screwdriver.
(2) Dismount the connector cover.
(3) Check that the packing (No. 09GAA374) has been attached correctly to the specified position.
(4) Connect the connecting cable with the U-WAVE-T.
(5) While pressing the connecting cable end with fingers, tighten the cable fixing screws so that no gap

appears between the cable connector and the U-WAVE-T.
(6) Make sure that no part of the packing is detached.

(1)     (5)

IMPORTANT

Do not connect the connecting cable forcibly in a state that the packing (No. 09GAA374) is not in the

correct position on the U-WAVE-T body. Otherwise, the packing may be damaged so that a failure
may be caused.

[4] Register the setting information of U-WAVE-R

After loaded with the battery and connected to a connecting cable, the U-WAVE-T needs to register the
setting information of U-WAVE-R.
Please read the “U-WAVEPAK User’s Manual“ in “PDF_Manual” folder of the CD supplied as a standard
accessory of U-WAVE-R for a detailed registering method and content.
“Adobe Reader” of Adobe Systems INC. is necessary to read.

IMPORTANT

• “Registering the setting information” should be performed by DATA switch of the connecting
cable before connecting to the Measuring tool.

• The registered information is stored after changing battery.

[5] Connecting to Measuring tool

• After registering the setting information, connect the U-WAVE-T to the Measuring tool.

• Clamp the cable leading to a Measuring tool using the supplied cable clamp or a Velcro fastener so
that measurement is not interfered and the LED display of the U-WAVE-T can be easily viewed.

IMPORTANT

• Exercise great caution about the cable routing,
Cable may be disconnected from the instrument or connection part may be damaged
if the excessive force is applied when the cable is snagged to the workpiece, etc..

• Tighten the connecting cable (02AZD790A, B, G) to the Measuring tool with the screw surely.



[6] Functions

1) Data communication

The U-WAVE-T performs data communication with DATA switch as shown below.

Transmits measurement data. t ≤ 2sec None
Transmits the Cancel command. 2 sec < t ≤ 5 sec Orange blinking
Executes U-WAVE-R search. 5 sec < t ≤ 10 sec Orange blinking

NOTE

• The Cancel command is a command to inform a U-WAVE-R of data error when wrong measurement
data is transmitted to the U-WAVE-R due to an operating error. However, the wrong measurement data

is not canceled by the command. It is to inform that the previous data is different from measuring value.

• When the U-WAVE-R search is executed, U-WAVE-T is connected with U-WAVE-R that
can be registered.

• If the DATA switch is held down for more than 10 seconds, the orange LED stops blinking and nothing
will function.



The U-WAVE-T can check whether to have performed normal communication with a U-WAVE-R
by a specific LED display (and buzzer sound).
However, buzzer sounds are available only for the buzzer type U-WAVE-T.

Wireless communication has been properly completed. Green LED blinking

• Wireless communication has failed.

• An error has occurred.

2) Initializing the setting information

If communication is disabled while using the U-WAVE-T, first refer to Troubleshooting
In U-WAVE-R User’s Manual, if communication is still disabled, initialize the setting information
registered in section 4 to default settings, and then retry communication.
Initialize the setting information with the following procedure.
(1) Remove the battery being loaded. For information about how to remove the battery, refer to section 2.
(2) While holding down the DATA switch on the connecting cable connector, reload the battery in

(3) Remount the battery cover, and set up the U-WAVE-T.

IMPORTANT

Once initialization is performed, the setting information used until then is all cleared.

Operations DATA switch push-down time t

Description of state LED Buzzer sound

place. The setting information is initialized.

LED

Short 2 times

Red LED blinking Long 1 time

[7] Specifications

Model IP67 type Buzzer type

Code No. 02AZD730D 02AZD880D

005WWCA0166(Japan)

Certification number

Protection class IP67 -

With/without buzzer Without With

Transmission output Less than 1 mW (0 dBm)

Distance of communication Approx. 20 m (line-of-sight distance under office environments)

A Conformity standard

Wireless communication protocol IEEE802.15.4 compatible

Communication frequency 2.405 to 2.475 GHz

Used band 15 channels (at intervals of 5 MHz)

Modulation method DSSS (Direct Sequence Spread Spectrum)

Wireless communication speed 250 Kbps

LED display Green/orange/red: 3 discrete color display

Battery CR2032 (3V): 1 piece

Battery life 400,000 times

Operating temperature (humidity) 0 to 40°C (20 to 80%RH, with no condensation)

Storage temperature (humidity) -10 to 60°C (20 to 80%RH, with no condensation)

External dimensions 44 X 29.6 X 18.5 (mm)

U-WAVE-T mass Approx. 23 g

VXU-02AZD730D (U.S.A)

4396B-02AZD730D (Canada)

Japan ARIB STD-T66
Europe EN 50371：2002

EN 300 440-1 V1.3.1 and EN 300 440-2 V1.1.2
EN 301 489-01 V1.6.1 and EN 301 489-03 V1.4.1

U.S.A ・47 CFR Part 15.247:(Subpart :C)

・47 CFR Part 15,(Subpart :B)

Canada・RSS-210 (Issue 7) and RSS-Gen (Issue 2)

・ICES 003 (Issue 4)

005WWCA0168(Japan)

VXU-02AZD880D (U.S.A)

4396B-02AZD880D (Canada)

○ Standard accessories

・User’s manual (this manual) No. 99MAL108B ・Precaution for the battery No.99MAL111W
・Size 0 screwdriver No. 05CZA619 ・Lithium battery ・ CR2032C(B)N ・Warranty card

○ Optional accessories No. 02AZD790A to G: Connecting cables (For details see section 8.)

[8] Connecting Cables

As for connecting cables, it is necessary to select a cable compatible with a Measuring tool to be used.
Use an appropriate connecting cable from among those in the following table.

Parts No. Model Series No,
02AZD790A
Water-resistant type
with data out switch type

02AZD790B
Water-resistant type with
data out switch type

02AZD790C
With data out switch type

02AZD790D
 10 pins type

02AZD790E
 6 pins type

02AZD790F
A flat form straight type



02AZD790G
Water-resistant type with
flat form straight type

500
500
571
572
573

293
293

--­329
350

--­468

500
571
572
500

--­178

179
515
518
519
542
543
544
544

572
574

164
227
227
293

--­293

--­339
337
468
515
568
810
810

192
500
511
543
543
550
551
552
570
547
572
574
575
811

543 ABS Digimatic Indicator ID-N/ID-B

ABS Coolant Proof Caliper CD-PMX/PM/GM
Super Caliper CD-SPM
ABS Coolant Proof Depth Gage VDS-PMX
ABS Coolant Proof Digimatic Scale Units SD-G
ABS Coolant Proof Exclusive Caliper NTD-PMX/PM

Coolant Proof Micrometer MDC-MJ/MJT
Coolant Proof Micrometer MDE-MJ
Coolant Proof Exclusive Micrometer （The end of the mark is –MJ）
Depth Micrometer DMC-M
Coolant Proof Digimatic Micrometer Heads MHN-M/MJ/MJN
Digimatic Exclusive Micrometer （The end of the mark is –M/PM）
Digimatic Holtest HTD-R

ABS Digimatic Caliper CD-CX/C
ABS Digimatic Depth Gage VDS-/DCX/DC
ABS Digimatic Scale Units SD-D/SDV-D
ABS Digimatic Caliper CD-SC
ABS Digimatic Exclusive Caliper （The end of the mark is –CX/C）

Surftest SJ-201/301/401/402
Digi-Derm DGE
CERA Height Master HMD-C
QM-Height QMH-S
Digital Mu-Checker M
Display Unit   EB/EC-D
Digimatic Indicator ID-H/ID-F
Laser Scan Micrometer LSM-9506
Laser Scan Micrometer LSM-6200/6900
(It applies when using Digimatic Codeout unit.（02AGC840）)
Difference/Sum Unit SD-U1
Heightmatic HDF
Digimatic Micrometer Heads MHD-M
Digimatic Micrometer Heads CLM-MH
Soft-Touch Micrometer CLM
Quickmike MDQ
Exclusive Quickmike （The end of the mark is –QM）
Digimatic Micrometer MDC-M
Digimatic Exclusive Micrometer （The end of the mark is -DM）
Digimatic Tubular Inside Micrometer IMJ-M
Digimatic Tubular Inside Micrometer IMZ-M
Digimatic Holtest HTD
Digital Height Master HME-DM
ABS Borematic SBM-C
Hardness Testing Machine HM-100/200/HV-100/HH-411
Rockwell Type Hardness Testing Machines HR-500
Digimatic Height Gage HDM-A/HD-A
Digimatic Caliper CD
ABS Digimatic Bore Gage CG-D
ABS Digimatic Indicator ID-S
ABS Digimatic Indicator ID-C
Digimatic Caliper CD
Digimatic Caliper CD
Digimatic Carbon Fiber Caliper CFC
ABS Digimatic Height Gage HDS-HC/C
ABS Digimatic Depth Gage
ABS Digimatic Scale Units SD-E/SDV-E/SD-V/SDV-F
Heightmatic HDF-N
ABS Digimatic Indicator ID-U
Hardness Testing Units HH-300

Product Name



Mitutoyo Corporation

20-1, Sakado 1-Chome, Takatsu-ku, Kawasaki-shi, Kanagawa 213-8533, Japan

ＫＡＷＡＳＡＫＩ,JAPAN