Mitutoyo 02AZD810C Users Manual

02AZD810C User Manual

Product U-WAVE-R
Model 02AZD810C
FCC ID VXU-02AZD810C
IC 4396B-02AZD810C

U-WAVE-R

Introduction

The U-WAVE-R in conjunction with a Mitutoyo U-WAVE-T (available separately) allows
wireless communication of the measurement data from Digimatic-output interfaced tool to load
it to a personal computer for data display.
To obtain the highest performance and the longest service life from the U-WAVE-R, carefully
read this User’s Manual thoroughly prior to use.
After reading this manual, keep it near the U-WAVE-R for quick reference.
The specifications of the U-WAVE-R and descriptions in this manual are subject to change
without prior notification.

Safety Precautions

Use the U-WAVE-R in conformance with the specifications, functions and precautions for use
given in this manual. If the U-WAVE-R is used in other way, it may jeopardize safety.

• Do not use the U-WAVE-R near a medical device that has a possibility of causing a

！

WARNING

Notes on Export Regulation

WARNING

Precautions for the Wireless Law

The country (region) that can use The U-WAVE-R by the code No. and certification number is
different. Please confirm U-WAVE-R must be in the country (region) that uses it in the table
below before it uses it.

Use excluding the country (region) specified by the certification number is prohibited by the law.

WARNING

Precaution for 02AZD810C (U.S.A and Canada type)

malfunction due to radio waves.

• The U-WAVE-R using an electric wave has a possibility that communication is
interrupted under the influence of external noises, etc., even within the distance of
communication of the electric wave. In this case take sufficient failure prevention
action (security measures).

• In the event the U-WAVE-R should fail, take sufficient failure prevention action
(security measures).

The U-WAVE-R falls into the Catch-All-Controlled Goods or Program under the

！

Category 16 of the Separate Table 1 of the Export Trade Control Order or the
Category 16 of the Separate Table of the Foreign Exchange Control Order,
based on the Foreign Exchange and Foreign Trade Law of Japan.
Further, this User's Manual and U-WAVE Quick Manual (No. 99MAL110B) also
falls into the Catch-All-Controlled Technology for use of the Catch-All-Controlled
Goods or Program, under the Category 16 of the Separate Table of the Foreign
Exchange Control Order.
If you intend re-exporting or re-providing the product or technology to any party
other than yourself, please consult with Mitutoyo prior to such re-exporting
or re-providing.

Country Japan , EU U.S.A , Canada

Code No. 02AZD810A 02AZD810C

Certification number

• The U-WAVE-R must follow the corresponding regulation which is specified in the

！

co untry to use an electric wave.

• The U-WAVE-R for Japan and Europe (02AZD810A) cannot be used in countries

other than Japan and Europe.

• The U-WAVE-R for U.S.A and Canada (02AZD810C) cannot be used in countries

other than U.S.A and Canada.

• Do not disassemble or modify any part of the U-WAVE-R.

• Do not peel off the following certification label stuck on the U-WAVE-R.

The use of any U-WAVE-R without the label is prohibited.

• Do not use the U-WAVE-R in an airplane.

The use of a wireless equipment in the airplane is prohibited.

005WWCA0038 （Japan）

Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Notes

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications, However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of
the following measures:

-- Increase the separation between the equipment and receiver.

Precautions on Wireless Communication Environments

Notice that this performance of the U-WAVE-R may not be fully delivered depending on the
environment such as a midway obstruction.
For the items of obstruction factors refer to the following table.

Concrete wall

Metallic partition, etc.
Wireless LAN, Bluetooth,

ZigBee, microwave oven,
and other communication
devices

Medical device

Item Description

VXU-02AZD810C (U.S.A)

4396B-02AZD810C (Canada)

Disables communication if the U-WAVE-R is completely
enclosed with a concrete wall.

Have the possibility of reducing the communication speed
or blocking communication.

Have the possibility of reducing the communication speed
or blocking communication. Separate the communication
channel (band ID) and installation site of each device as far
as possible from those of the U-WAVE-R.

Do not use the U-WAVE-R near a medical device such as a
laser surgical knife and a bathroom scale.

User’s Manual

No.99MAL109B2

Precautions for Use

The following deeds and situations will cause a failure or malfunction in the U-WAVE-R.
Care should be exercised.

IMPORTANT

• The U-WAVE-R operates on the power supply from a personal computer. A personal
computer may generate large noises depending on the manufacturer and model. Be sure to
verify the whole system operation once prior to use.

• Do not give a sudden shock such as a drop or apply an excessive force to the U-WAVE-R.

• If the U-WAVE-R is not used more than 3 months, disconnect the U-WAVE-R from the
personal computer and store it in a safe place.

• Avoid using or storing the U-WAVE-R at sites which are exposed to direct sunlight,
excessively high or low temperature.

• Avoid using or storing the U-WAVE-R at sites where it may be subject to the adhesion of
solution such as acid and alkali or organic solvent.

• If a high-voltage device such as an electro-spark engraving pen is used for the U-WAVE-R,
the internal electronic parts may be damaged.

• Exercise care so as not to apply an undue force or curvature to the USB cable.

Warranty

In the event that the U-WAVE-R should prove defective in workmanship or material, within
one year from the date of original purchase for use, it will be repaired or replaced, at our

option, free of charge upon its prepaid return to us.

This warranty is effective only where the U-WAVE-R is properly installed and operated in
conformance with the instructions in this manual.

Disposal of Old Electrical & Electronic Equipment (Applicable in the European
Union and other European countries with separate collection systems)

This symbol on the U-WAVE-R or on its packaging indicates that the U-WAVE-R shall
not be treated as household waste. To reduce the environmental impact of WEEE
(Waste Electrical and Electronic Equipment) and minimize the volume of WEEE
entering landfills, please reuse and recycle.
For further information, please contact your local dealer or distributors.

[1] Name of Each Part and External Dimensions (Unit : mm)

1. POWER (Green LED) 2. ERROR (Red LED) 3. USB connector

4. INIT. Switch (Initialize switch) 5. Device ID label 6. Certification label

6. Certification label
(This label is different according

to the country (region).)

5. Device ID label

[2] Software Installation

The U-WAVE-R outputs measurement data to a personal computer using the dedicated
software “U-WAVEPAK” included in the CD supplied as a standard accessory.
Before using the U-WAVE-R be sure to read the standard accessory

“U-WAVE QUICK Manual” thoroughly, and then install the “U-WAVEPAK” and “USB Driver”.

IMPORTANT

• Log in to Windows by ‘Administrator’.

• Be sure to install the U-WAVEPAK before connecting the U-WAVE-R to a personal computer.

• When connecting the U-WAVE-R to a USB Hub, always use a self-powered USB Hub.

• The U-WAVE-R does not support the operation in the Standby or Hibernate of a personal
computer. Cancel each setting in the U-WAVE-R prior to use.

• Please read the “U-WAVEPAK User’s Manual“ in “PDF_Manual” folder of the CD supplied as a
standard accessory for a detailed operation method of U-WAVEPAK.

“Adobe Reader” of Adobe Systems INC. is necessary to read.

4. INIT. switch

3. USB connector

1. POWER
(Green LED)

2. ERROR

(Red LED)

[3] Setup

1) Setting the communication information

You need to set various information necessary for communication in the U-WAVE-R using
the U-WAVEPAK. (No information is registered default setting.)
The information required to be set is as shown in the following table.

Item name Description

Group ID

Band ID Number of a radio band to be used

Lack of data
monitoring
level

IMPORTANT

• Please read the “U-WAVE Quick manual “ and “U-WAVEPAK User’s Manual“ in “PDF_Manual”
folder of the CD supplied as a standard accessory for setting the communication information.

• The U-WAVE-R will not function properly if a U-WAVE-R with the same group ID and band
ID settings exists nearby. Be sure to set different information for each ID in the U-WAVE-R.

ID for grouping the U-WAVE-T and the U-WAVE-R.
Communication is possible between the U-WAVE-T and the U-WAVE-R
which have the same ID.

The data transmitted from the U-WAVE-T to the U-WAVE-R includes a value
that is incremented by one each time communication is implemented.
The U-WAVE-R monitors this value and has a function to notify the personal
computer of a data missing error.
A lack of data monitoring level is a value for prescribing how frequently this
error is notified.