MITSUBISHI XL25 User Guide
PLEASE READ
We are in no way responsible for the
contents of the manual. We do not guarantee
its accuracy and we do not make any claim
of copyright. The copyright remains the
property of their respective owners.
Visit the site to read the latest projector
news and reviews, read and comment on
projector specifications, download user
manuals and much more.
LCD
Projector
User Manual
ENGLISH
FRANÇAIS
DEUTSCH
XL30
XL25
ITALIANO
ESPAÑOL
SL25
MODEL XL30U/XL25U/SL25U
EN – 1
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If you
use another power-supply cord, it may cause interference with radio and television reception.
Use the attached RGB cable, RS-232C cable with this
equipment so as to keep interference within the limit
of a FCC Class B device.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS
WHEN PROJECTOR IS IN THE POWER ON
MODE.
When using the projector in Europe
COMPLIANCE NOTICE
This LCD - Video Projector complies with the requirements of the EC Directive 89/336/EEC “EMC
Directive” as amended by Directive 93/68/EEC and
73/23/EEC “Low Voltage Directive” as amended by
Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen
at a level that gains proper operation in residential
areas, on business and light industrial premises and
on small-scale enterprises, inside as well as outside
of the buildings. All places of operation are
characterised by their connection to the public low
voltage power supply system.
WARNING
Use the attached RGB cable or RS-232C cable with
this equipment so as to keep interference within the
limits of a EN55022 Class B. Use the shielded DSUB/5 BNC cable with this equipment so as to keep
interference within the limits of a EN55022 Class B.
Please follow WARNINGS instructions.
EN – 2
Contents
Important safeguards ...........................................................................4
Overview ............................................................................................... 6
Using the remote control ......................................................................8
Battery installation ......................................................................................................... 8
Installation ............................................................................................9
Basic connections ............................................................................... 10
Projector + AV equipment............................................................................................. 10
Projector + DVD player or HDTV decoder ................................................................... 10
Projector + personal computer ...................................................................................... 11
Preparing the projector for operation ............................................... 12
To operate projector power ON.......................................................... 13
Menu operation .................................................................................. 15
Picture adjustment............................................................................. 18
Advanced feature for presentation .................................................... 20
Expand ........................................................................................................................... 20
PinP (Picture in Picture) ............................................................................................... 20
Still ................................................................................................................................. 20
Mouse remote control .................................................................................................... 21
Lamp replacement ............................................................................. 22
Maintenance ....................................................................................... 23
Troubleshooting.................................................................................. 24
ENGLISH
Indicators ............................................................................................ 25
Specifications ...................................................................................... 26
Kensington Lock ............................................................................................................ 26
Connectors ..................................................................................................................... 27
Dimensional drawings .................................................................................................. 27
What’s included in the box............................................................................................ 27
Replacement part .......................................................................................................... 27
Specification of RGB signals in each computer mode of the projector ....................... 28
C
Trademark, Registered trademark
Windows 98 and Windows 95 are registered trademarks of Microsoft in the U.S. and other countries.
Macintosh is registered trademark of Apple Computer Inc.
IBM and PS/2 are trademarks or registered trademarks of International Business Machines Corporation.
MicroSaver and Kensington are registered trademarks of Kensington Technology Group.
Other brand or product names are trademarks or registered trademarks of their respective holders.
EN – 3
Important safeguards
Please read all these instructions regarding your LCD
projector and retain them for future reference. Follow
all warnings and instructions marked on the LCD projector.
1. Read instructions
All the safety and operating instructions should
be read before the appliance is operated.
2. Retain instructions
The safety and operating instructions should be
retained for future reference.
3. Warnings
All warnings on the appliance and in the operating instructions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment
without the approval of the manufacturer as
such additions may result in the risk of fire, electric shock or other personal injury.
7. Water and moisture
Do not use this projector near water or in contact with water.
8. Accessories
Do not place this projector on an unstable cart,
stand, tripod, bracket or table. Use only with a
cart, stand, tripod bracket, or table recommended by the manufacturer or sold with the
projector. Any mounting of the appliance should
follow the manufacturer's instructions and
should use a mounting accessory recommended
by the manufacturer.
An appliance and cart combination should be
moved with care. Quick stops, excessive force and
uneven surfaces may cause the appliance and
cart combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided
for ventilation, ensuring reliable operation of the
projector and to protect it from overheating. Do
not block these openings or allow them to be
blocked by placing the projector on a bed, sofa,
rug, or bookcase. Ensure that there is adequate
ventilation and that the manufacturer's instructions have been adhered to.
10. Power sources
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power,
please consult your appliance dealer or local
power company.
11. Power-cord protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles,
and points where they exit from the appliance. Do
not put the power cord under a carpet.
12. Overloading
Do not overload wall outlets and extension cords
as this can result in a fire or electric shock.
13. Objects and liquids
Never push objects of any kind through openings of this projector as they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the projector.
14. Servicing
Do not attempt to service this projector yourself. Refer all servicing to qualified service personnel.
15. Damage requiring service
Unplug this projector from the wall outlet and
refer servicing to qualified service personnel under the following conditions:
(a) If the power-supply cord or plug is dam-
aged.
(b) If liquid has been spilled, or objects have
fallen into the projector.
(c) If the projector does not operate normally
after you follow the operating instructions.
Adjust only those controls that are covered
by the operating instructions. An improper
adjustment of other controls may result
in damage and may often require extensive work by a qualified technician to restore the projector to its normal operation.
(d) If the projector has been exposed to rain
or water.
(e) If the projector has been dropped or the
cabinet has been damaged.
(f) If the projector exhibits a distinct change
in performance - this indicates a need for
service.
16. Replacement parts
When replacement parts are required, be sure
that the service technician has used replacement
parts specified by the manufacturer or parts
having the same characteristics as the original
part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
17. Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is
in a safe operating condition.
EN – 4
WARNING:
Unplug immediately if there is something
wrong with your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fire or electric
shock. In this case, unplug immediately and contact
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the Owner's
Guide, do not attempt to service this product
yourself. Please contact your dealer when you want
to fix, adjust or inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or
drop it. Unplug the projector and contact your dealer
for inspection. It may lead to fire if you keep using
the equipment.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven
surface.
Place the projection on a leveled and stable surface
only. Please do not place equipment on unstable
surfaces.
Do not look into the lens when it is
operating.
It may hurt your eyes.Never let children look into
the lens when it is on.
Do not turn off the main power abruptly or
unplug the projector during operation.
It can lead to lamp breakage, fire, electric shock or
other trouble. It is best to wait for the fan to turn off
before turning main power off.
Do not touch Air outlet grille and Bottom
plate which becomes hot.
Do not touch them or put other equipment in front of
Air outlet grille. The heated Air outlet grille and Bottom plate may cause injury or damage to other equipment. Also, do not set the projector on the desk which
is easily affected by heat.
Clean the air-filter once a month.
Clean the air-filter frequently. If the filter or ventilation slots become clogged with dirt or dust, the temperature inside of the projector may rise and cause
some troubles, such as damage of inside parts, and
shortening the life of panel.
Do not look into the air outlet grille when
projector is operating.
Heat, dust etc. may blow out of it and hurt your eyes.
Place of installation
For safety’s sake, refrain from setting the projector at
any place subjected to high temperature and high
humidity. Please maintain an operating temperature,
humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C) and
+95°F (+35°C)
• Operating humidity: between 30 and 90%
• Never put any heat-producing device under the pro-
jector so that the projector does not overheat.
• Do not attach the projector to a place that is unstable or subject to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from
installing near the projector any cable carrying a
large current.
• Place the projector on a solid, vibration free surface: otherwise it may fall, causing serious injury
to a child or adult, and serious damage to the product.
• Do not stand the projector: it may fall, causing serious injury and damage to the projector.
• Slanting the projector more than ±15˚(right and left
or front and rear) may cause trouble or explosion of
the lamp.
• Do not place the projector near air-conditioning unit
or heater to avoid hot air to the exhaust and ventilation hole of the projector.
ENGLISH
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.
EN – 5
Overview
12 345 6
1 Remote control sensor (Front)
2 Air outlet grille
3 Zoom
4 Focus
5 Control panel
6 Kensington Security Lock Standard
connector
7 Easy-carry handle
8 Foot adjustment buttons (Left/Right)
9 Lens
10 Air outlet grille
Control panel
1
2
3
4
5
6
7
8
910
87
14
13
12
11
10
1 LAMP indicator
2 TEMP (temperature) indicator
3 AUTO POSITION button
4 ENTER button
5 MENU button
6 COMPUTER button
7 VOLUME (+, –) buttons
8 KEYSTONE (+, –) buttons
9 RIS sensor
10 VIDEO button
1 1 Direction buttons
12 MUTE button (Audio/Video)
13 POWER button
14 POWER indicator
9
Rear panel
12436789511
10
1213141516
1 Remote control sensor (Rear)
2 USB terminal
3 RS-232C (DIN 8P) terminal
4 Reset button
5 Wired remote control (REMOTE) jack
6 COMPUTER / COMPONENT VIDEO IN 1
terminal (D-SUB mini 15P)
7 COMPUTER AUDIO IN jack
8 MONITOR OUT terminal (D-SUB mini 15P)
9 AUDIO OUT jack
10 Main power
I : ON
O : OFF
1 1 Air inlet grille
12 Power jack
13 Ground terminal
14 COMPUTER / COMPONENT VIDEO IN 2
terminal ( R/PR, G/Y, B/PB, H/HV, V )(BNC)
15 Video/audio input terminals
16 Speaker
EN – 6
Bottom side
CAUTION
1
1 Adjustment foot (Left/Right)
2 Lamp cover
3 Air inlet grille/Filter cover
ENGLISH
Remote control
1
2
4
5
6
7
8
9
10
11
12
13
KEYSTONE
EXPAND
–
MENU
MUTE
VOLUME
DVD VIDEO
COMPUTER
1
VIDEO
1
P in P AUTO POSITION
LASER
+
ENTER
R-CLICK
16 : 9
STILL
MEMORY
SELECT
2
Caution:
Do not replace the lamp immediately after using the
projector because the lamp has got extremely hot.
3
1 Laser aperture
2 Transmission window
3 Wired remote control jack
4 Indicator
5 POWER button
3
6 KEYSTONE button
7 EXPAND button
8 + , – (VOLUME) buttons
9 Mouse pointer
10 MENU button
2
2
24
23
22
21
20
1 1 STILL button
12 MUTE button (Audio/Video)
13 Programmable buttons
14 SELECT switch
15 MEMORY button
16 16 : 9 button
17 ENTER button
19
18
17
16
18 R-CLICK button (For mouse)
19
Direction buttons
20 LASER button
21 AUTO POSITION button
22 PinP button
23 VIDEO 1, 2 button
24 COMPUTER 1, 2 button
15
25 Left click button (For mouse)
• The + and - buttons are used in the KEYSTONE
adjustment and the EXPAND mode in addition to the
volume control.
14
• Pressing the LASER button emits a laser beam. Even
when you keep holding down the LASER button, it is
emitted only one minute. To keep emitting it longer,
press the LASER button again.
• You can disable the LASER button to prevent
laser radiation due to misuse of the button.
How to disable the LASER button
While holding the LASER button down, press the }
25
button three times.
• To enable the LASER button, while holding the LASER
button down, press the { button three times.
About the laser beam
AVOID EXPOSURE-LASER
RADIATION IS EMITTED
FROM THIS APERTURE
CAUTION
LASER RADIATION
DO NOT STARE INTO BEAM
WAVE LENGTH: 640-660nm
MAX OUTPUT : 1mW
CLASS 2 LASER PRODUCT
Complies with 21 CFR, 1040.10 AND 1040.11
IEC 60825-1:1993+A1:1997
This remote control is a Class 2 laser product. (Max. output : 1 mW, Wavelength
: 640-660 nm)
Beam Divergence : 6m distance about 10.0mm x 10.0mm (±6.0mm)
CAUTION :
• Pressing the LASER button on the remote control emits a laser beam. Do not
look into the laser beam directly. Do not point the laser beam at anyone.
Looking at the laser beam directly may damage eyesight.
• Use of controls or adjustments or procedures other than those specified herein may
result in hazardous radiation exposure.
EN – 7
Using the remote control
Battery installation
Use two AA size batteries.
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the
arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
3. Replace the back cover.
12 3
Important:
• Do not use a new battery with an old one.
• Load batteries in the correct position.
• Do not heat, take apart, or throw batteries into fire.
• Do not try to recharge batteries. Do not use rechargeable batteries.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes
in contact with your eyes, rinse them with water and then consult your doctor.
Operation area (for wireless control system)
The range for operation is about 10 m (about 32 feet) when the remote control points to the projector. The distance to the screen back to the projector must be less than 7 m (about 23 feet). Depending on the type of the
screen, the distance will be different.
20˚
5˚
20˚
5˚
30˚30˚
20˚
Important:
Avoid the direct sunlight or fluorescent light to the remote control sensor. Also keep the distance of more than 2 m
(6.5") between the remote control sensor and fluorescent lamp on the remote control may not work correctly.
20˚
Using the wired remote control
Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired
remote control is useful for operating in a distance or outside of the operating area.
• When the remote control is connected with remote
control cable, it does not work as a wireless
remote control.
• When you need a longer cable, use a pin-pin cable.
• When using the wired remote control, the laser beam may be darker. It is normal.
EN – 8
Installation
Orientation of the projector
Picture size can be set by changing the distance between the screen and the projector.
Front projection
Height
H
Screen
(between the screen and
L
the head of the projector)
Screen
Width
A
B
A=B
To find the approximate distance
between the projector and screen:
Multiply the width of the screen
x 1.8 (min.) , Multiply the width of
the screen x 2.3 (max.).
• Refer to the chart for recommended distances in maximum
zoom and minimum zoom.
ENGLISH
Screen
Diagonal size Width Height
(inch)
40 "
60 "
80 "
100 "
150 "
200 "
250 "
300 "
• The above numbers are approximate, and may be slightly different from the actual measurements.
Front projection, ceiling mount
For ceiling mount, you need the ceiling mount kit.
Ask a specialist for installation. For more details,
consult your dealer.
• This warranty does not cover damage caused by
the use of any unrecommended ceiling mount kit
and the installation of the ceiling mount kit at an
improper location.
• When using the ceiling mount, set IMAGE REVERSE in the INSTALLATION menu to MIRROR INVERT. See Page 16.
• Projected images may appear darker when the
unit is used as a ceiling installation than when it
is used in the tabletop position. This does not
signify a product malfunction.
Rear projection
Ask a specialist for installation. For more details,
consult your dealer.
(cm)
102
152
203
254
381
508
635
762
(inch)
32 "
48 "
64 "
80 "
120 "
160 "
200 "
240 "
SCREEN
(cm)
81
122
163
203
305
406
508
610
(inch)
24 "
36 "
48 "
60 "
90 "
120 "
150 "
180 "
(cm)
61
91
122
152
229
305
381
457
Distance from screen (L) / (approximate)
Maximum
zoom (WIDE)
(inch)
55 "
84 "
114 "
143 "
215 "
288 "
361 "
434 "
• For rear projection, set IMAGE REVERSE in the
Caution:
• Placing the projector on a carpet reduces ventila-
• Place the projector more than 50 cm (20 in.) from
• Do not use the projector under the following
Important:
• Do not put stress on the lens, as this may cause
(m)
1.4
2.1
2.9
3.6
5.5
7.3
9.2
11.0
INSTALLATION menu to MIRROR. See Page 16.
tion from the fan at the bottom and might cause
problems. Place a hard board or similar item
under the projector to facilitate ventilation of the
unit.
the wall to prevent blocking the intake, exhaust
slots andventilation of this projector because hot
air comes out of it.
circumstances, which may cause fire or electric
shock.
• in a dusty or humid place
• while the projector is lying sideways or upside
down
• near a heater
• in a kitchen or oily, smoky or damp place
• in direct sunlight
• with high temperature, such as a closed car
• where the temperature is lower than 41°F
(+5˚C) or higher than 95°F (35˚C).
damage.
Minimum
zoom (TELE)
(inch)
71 "
107 "
144 "
181 "
272 "
364 "
–
–
(m)
1.8
2.7
3.7
4.6
6.9
9.3
Height projected
(inch)
1.2 "
1.8 "
2.4 "
3.0"
4.5 "
6.0 "
–
–
7.5 "
9.0 "
image (H)
(cm)
3.0
4.6
6.1
7.6
11.4
15.2
19.1
22.9
SCREEN
EN – 9
Basic connections
This projector can be connected with various devices such as a VCR, video camera, videodisc player, and personal
computer that have analog RGB output connectors.
Important:
• Make sure that the connected device is turned off before starting connection.
• Plug in the projector and the connected devices firmly, and unplug them by holding and pulling out their
power plugs, not by pulling the power cords.
• When the projector and the connected devices are located too close to each other, the projected image may be
affected by their interference.
• See the owner’s guide of each device for details about their connections.
Projector + AV device
Important:
• Connect the video and audio plugs of the AV cable to the proper terminals matching their colors respectively.
• The S-video signal takes priority over the video signal. When you input both the S-video signal and the
normal video signal at the same time, the normal video signal is ignored.
• When the connected AV device uses a BNC connector for its video output, connect it to the VIDEO IN2 (BNC)
terminal. When both the VIDEO IN2 (BNC) terminal and the VIDEO IN2 (RCA) terminal are engaged at the
same time, the image supplied to the VIDEO IN2 (RCA) terminal takes priority.
VCR, etc.
To audio output
Connect either
one of these.
To audio input
To video input
To S-video input
To video output
To S-video output
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fitting (Y, CB, CR). When connecting such a DVD player
with this projector, use the COMPUTER/COMPONENT VIDEO 2 IN terminal.
DVD player or HDTV decoder
CB(PB)
Y
C
R(PR
)
B G R
BNC-BNC cable (option)
to AUDIO OUT
BNC - RCA connector
(option)
AUDIO cable
R/P
R
G/Y
B/P
B
To COMPUTER
AUDIO IN
• The terminals’ names Y, PB, and PR are examples of a case where a HDTV decoder is connected.
• The terminals’ names are different depending on the connected devices.
• Use BNC-BNC cables for connection.
• The image may not be projected correctly with some DVD players.
• When connecting a HDTV decoder having RGB output terminals, set the COMPUTER INPUT to RGB in the
SIGNAL menu.
EN – 10
Loading...